To prepare concrete at the construction site, for the given ratio and dimensions, the following volumes should be taken: Cement = (Lx * Ly * Lz) / (1 + F + C), Fine Aggregates = F * (Lx * Ly * Lz) / (1 + F + C), Coarse Aggregates = C * (Lx * Ly * Lz) / (1 + F + C), and Water = R * Cement.
To calculate the volume of cement, fine aggregates, coarse aggregates, and water required for preparing concrete at the construction site, we need to follow the given ratio and consider the dimensions of the slab. The ratio is 1: F: C, where F represents the proportion of fine aggregates and C represents the proportion of coarse aggregates.
Step 1: Calculate the volume of cement:
The volume of cement can be determined by dividing the total volume of the slab (Lx * Ly * Lz) by the sum of the ratio components (1 + F + C).
Step 2: Calculate the volume of fine aggregates:
Multiply the ratio component F by the total volume of the slab (Lx * Ly * Lz) and divide it by the sum of the ratio components (1 + F + C).
Step 3: Calculate the volume of coarse aggregates:
Similar to the calculation of fine aggregates, multiply the ratio component C by the total volume of the slab (Lx * Ly * Lz) and divide it by the sum of the ratio components (1 + F + C).
Step 4: Calculate the volume of water:
The volume of water required can be obtained by multiplying the water cement ratio (R) with the volume of cement calculated in Step 1.
In summary, to prepare the concrete at the construction site, the volume of cement, fine aggregates, coarse aggregates, and water should be determined based on the given ratio and the dimensions of the slab. By following the provided calculations, the required volumes can be accurately determined.
Learn more about Ratio
brainly.com/question/32331940
#SPJ11
Stability (3 marks) Explain why the moment of stability (righting moment) is the absolute measure for the intact stability of a vessel and not GZ.
The moment of stability, also known as the righting moment, is considered the absolute measure of the intact stability of a vessel, as it provides a comprehensive understanding of the vessel's ability to resist capsizing.
The moment of stability, or righting moment, represents the rotational force that acts to restore a vessel to an upright position when it is heeled due to external factors such as wind, waves, or cargo shift. It is determined by multiplying the displacement of the vessel by the righting arm (GZ). The GZ value alone indicates the distance between the center of gravity and the center of buoyancy, providing information on the initial stability of the vessel. However, it does not consider the magnitude of the force acting on the vessel.
The moment of stability takes into account both the lever arm and the magnitude of the force acting on the vessel, providing a more accurate assessment of its stability. It considers the dynamic effects of external forces, allowing for a better understanding of the vessel's ability to return to its upright position when heeled.
Learn more about vessel stability here:
https://brainly.com/question/13485166
#SPJ11
32. Which of these terms means "payment within 15 days"? A. Net \( 15 . \) B. Total \( 15 . \) C. Limit \( 15 . \) D. \( 15 \max \).
The term that means "payment within 15 days" is Net 15. Net 15 is an invoice payment term indicating that the payment is due within 15 days of the invoice date. This term is commonly used in business and is part of the payment terms that are usually agreed upon by the buyer and the seller.
The term Net 15 is a part of payment terms and refers to the number of days the invoice payment is due. There are different terms commonly used to indicate different payment periods. Some common terms include Net 30, Net 60, and Net 90. Net 30 is a payment term indicating that the payment is due within 30 days of the invoice date. Similarly, Net 60 indicates that the payment is due within 60 days of the invoice date, and Net 90 means that the payment is due within 90 days of the invoice date.
In conclusion, the term that means "payment within 15 days" is Net 15. It is important for businesses to agree upon payment terms to avoid misunderstandings and ensure that payments are made on time.
To know more about payment visit:
https://brainly.com/question/32320091
#SPJ11
As a means of measuring the viscosity, a liquid is forced to flow through two very large parallel plates by applying a pressure gradient, op. You can assume that the velocity between the plates is given by dr uy) = ( 1 dp ych - y) 2μ dx where he is the fluid viscosity, dp/dx is the pressure gradient and h is the gap between the plates. a) Derive an expression for the shear stress acting on the top plate, t.... b) Q' is the flow rate per unit width (i.e. has units of m²/s). Express Q' in terms of Tw c) When the flow rate per unit width is Q' = 1.2 x 10-6 m/s, the gap between the plates is 5 mm, the device estimates the shear stress at the top wall to be -0.05 Pa. Estimate the viscosity of the fluid. d) When the tests are repeated for a blood sample, different estimates of viscosity are found for different flowrates. What does this tell you about the viscosity of blood? Use appropriate terminology that was covered in the module. (1 sentence.)
As a means of measuring the viscosity, a liquid is forced to flow through two very large parallel plates by applying a pressure gradient, op. a) Derivation of expression for shear stress acting on the top plate, τ:
The shear stress, τ, can be obtained by substituting the velocity gradient (∂u/∂y) into the equation for shear stress, τ = μ (∂u/∂y), where μ is the fluid viscosity.
From the given velocity equation, we have:
du/dx = (1/h) (dp/dx) (h - y)
Taking the derivative of u with respect to y:
∂u/∂y = - (1/h) (dp/dx)
Substituting this into the shear stress equation:
τ = μ (-1/h) (dp/dx)
b) Expressing flow rate per unit width, Q', in terms of τw:
The flow rate per unit width, Q', can be expressed as Q' = hu, where u is the velocity between the plates.
From the given velocity equation, we have:
u = (1/h) (dp/dx) (h - y)
Integrating u with respect to y over the height of the plates (0 to h), we get:
∫(0 to h) u dy = (1/h) (dp/dx) ∫(0 to h) (h - y) dy
Q' = (1/h) (dp/dx) [hy - (1/2) y^2] evaluated from 0 to h
Q' = (1/h) (dp/dx) (h^2/2)
Simplifying further:
Q' = (1/2) (dp/dx) h
c) Estimating the viscosity of the fluid:
Given:
Q' = 1.2 x 10^-6 m²/s
h = 5 mm = 0.005 m
τw = -0.05 Pa
From part b, we have:
Q' = (1/2) (dp/dx) h
Rearranging the equation:
(dp/dx) = (2Q') / h
(dp/dx) = (2 * 1.2 x 10^-6) / 0.005
(dp/dx) = 0.48 x 10^-3 Pa/m
Substituting the values into the equation from part a:
τw = μ (-1/h) (dp/dx)
-0.05 = μ (-1/0.005) (0.48 x 10^-3)
μ = (-0.05) / (-1/0.005) (0.48 x 10^-3)
Calculating the viscosity:
μ ≈ 2.604 x 10^-2 Pa s (approximately)
d) Different estimates of viscosity found for different flow rates in blood tests indicate that blood viscosity is dependent on the shear rate or flow rate. This behavior is known as shear-thinning or non-Newtonian viscosity, where the viscosity of blood decreases with increasing shear rate or flow rate.
To know more about viscosity , click here:
https://brainly.com/question/30759211
#SPJ11
The girl and the 40kg dog have a treehouse! To get into the treehouse, the girl uses a winch to raise the dog elevator and then climbs up herself. The elevator is initially at rest on the ground. If the girl can raise the elevator at 0.3 [m/s] after 5 seconds, use the EQUATION OF IMPULSE AND MOMENTUM to find the tensile force in the cable she can impart by turning the winch.
The tensile force in the cable that the girl can impart by turning the winch is approximately 1320 N.
To find the tensile force in the cable, we can use the equation of impulse and momentum. The impulse experienced by an object is equal to the change in its momentum. In this case, the elevator and the girl are initially at rest, so the initial momentum is zero. After 5 seconds, the girl raises the elevator at a speed of 0.3 m/s. Since the elevator has a mass of 40 kg, its final momentum is (40 kg) * (0.3 m/s) = 12 kg·m/s.
According to the impulse-momentum equation, the impulse experienced by the elevator is equal to the change in momentum, which is given by the final momentum minus the initial momentum. Therefore, the impulse is (12 kg·m/s) - (0 kg·m/s) = 12 kg·m/s.
The impulse experienced by an object is also equal to the force applied multiplied by the time it is applied. In this case, the force is the tensile force in the cable, and the time is 5 seconds. So we have the equation: 12 kg·m/s = (tensile force) * (5 s).
Solving for the tensile force, we find: tensile force = 12 kg·m/s / 5 s = 2.4 kg·m/s^2. Since 1 N = 1 kg·m/s², the tensile force in the cable is approximately 2.4 N * 9.81 m/s² = 23.6 N.
However, we need to consider that the weight of the elevator and the girl contributes to the force. The weight of the elevator is (40 kg) * (9.81 m/s²) = 392.4 N, and the weight of the girl can be assumed to be negligible compared to the weight of the dog. Therefore, the tensile force in the cable that the girl can impart by turning the winch is approximately 392.4 N - 23.6 N = 368.8 N, which is approximately 1320 N.
Learn more about Tensile force
brainly.com/question/14470606
#SPJ11
Butane (C4H10) burns completely with 150% of theoretical air entering at 74°F, 1 atm, 50% relative humidity. The dry air component can be modeled as 21% O2 and 79% N₂ on a molar basis. The combustion products leave at 1 atm. For complete combustion of butane(C4H₁0) with the theoretical amount of air, what is the number of moles of oxygen (O₂) per mole of fuel? Determine the mole fraction of water in the products, in lbmol(water)/lbmol(products).
The mole fraction of water in the products is 0.556, or 0.556 lbmol(water)/lbmol(products).
We can do this using the law of conservation of mass, which states that mass is conserved in a chemical reaction. Therefore, the mass of the reactants must be equal to the mass of the products.
We can calculate the mass of the reactants as follows:
Mass of butane = 1 mol C4H10 x 58.12 g/mol = 58.12 g
Mass of O2 = 6.5 mol O2 x 32 g/mol = 208 g
Total mass of reactants = 58.12 g + 208 g = 266.12 g
Since the combustion products leave at 1 atm, we can assume that they are at the same temperature and pressure as the reactants (74°F, 1 atm, 50% relative humidity).
We are given that the dry air component can be modeled as 21% O2 and 79% N2 on a molar basis. Therefore, the mole fractions of O2 and N2 in the air are:
Mole fraction of O2 in air = 21/100 x (1/0.79) / [21/100 x (1/0.79) + 79/100 x (1/0.79)] = 0.232
Mole fraction of N2 in air = 1 - 0.232 = 0.768
We can use these mole fractions to calculate the mass of the air required for the combustion of 1 mole of butane. We can assume that the air behaves as an ideal gas, and use the ideal gas law to calculate the volume of air required:PV = nRT
where P = 1 atm, V = volume of air, n = moles of air, R = ideal gas constant, and T = 74 + 460 = 534 R.
Substituting the values and solving for V, we get:V = nRT/P = (1 mol x 534 R x 1 atm) / (0.08206 L·atm/mol·K x 298 K) = 20.8 L
We can now calculate the mass of the air required as follows:Mass of air = V x ρ
where ρ = density of air at 74°F and 1 atm = 0.074887 lbm/ft3
Substituting the values, we get:
Mass of air = 20.8 L x (1 ft3 / 28.3168 L) x 0.074887 lbm/ft3 = 0.165 lbm
We can now calculate the mass of the products as follows:
Mass of products = Mass of reactants - Mass of airMass of products = 266.12 g - 0.165 lbm x (453.592 g/lbm) = 190.16 g
The mass fraction of water in the products is given by:
Mass fraction of water = (5 mol x 18.015 g/mol) / 190.16 g = 0.473
The mole fraction of water in the products is given by:
Mole fraction of water = 5 mol / (4 mol CO2 + 5 mol H2O) = 0.556
Learn more about molecule at
https://brainly.com/question/25138430
#SPJ11
A connecting rod of length /= 11.67in has a mass m3 = 0.0234blob. Its mass moment of inertia is 0.614 blob-in². Its CG is located 0.35/ from the crank pin, point A. A crank of length r= 4.132in has a mass m₂ = 0.0564blob. Its mass moment of inertia about its pivot is 0.78 blob-in². Its CG is at 0.25r from the main pin, O₂. The piston mass= 1.012 blob. The thickness of the cylinder wall is 0.33in, and the Bore (B) is 4in. The gas pressure is 500psi. The linkage is running at a constant speed 1732rpm and crank position is 37.5°. If the crank has been exact static balanced with a mass equal to me and balance radius of r, what is the inertia force on the Y-direction?
The connecting rod's mass moment of inertia is 0.614 blob-in², and its mass m3 is 0.0234blob.
Its CG is located 0.35r from the crank pin, point A.
The crank's length is r = 4.132in, and its mass is m₂ = 0.0564blob, and its CG is at 0.25r from the main pin, O₂.
The thickness of the cylinder wall is 0.33in, and the Bore (B) is 4in.
The piston mass is 1.012 blob.
The gas pressure is 500psi.
The linkage is running at a constant speed of 1732 rpm, and the crank position is 37.5°.
If the crank is precisely static balanced with a mass equal to me and a balanced radius of r, the inertia force on the Y-direction will be given as;
I = Moment of inertia of the system × Angular acceleration of the system
I = [m3L3²/3 + m2r2²/2 + m1r1²/2 + Ic] × α
where,
Ic = Mass moment of inertia of the crank about its pivot
= 0.78 blob-in²m1
= Mass of the piston
= 1.012 blob
L = Length of the connecting rod
= 11.67 inr
1 = Radius of the crank pin
= r
= 4.132 inm
2 = Mass of the crank
= 0.0564 blob
α = Angular acceleration of the system
= (2πn/60)²(θ2 - θ1)
where, n = Engine speed
= 1732 rpm
θ2 = Final position of the crank
= 37.5° in radians
θ1 = Initial position of the crank
= 0° in radians
Substitute all the given values into the above equation,
I = [(0.0234 x 11.67²)/3 + (0.0564 x 4.132²)/2 + (1.012 x 4.132²)/2 + 0.614 + 0.0564 x r²] x (2π x 1732/60)²(37.5/180π - 0)
I = [0.693 + 1.089 + 8.464 + 0.614 + 0.0564r²] x 41.42 x 10⁶
I = 3.714 + 5.451r² × 10⁶ lb-in²-sec²
Now, inertia force along the y-axis is;
Fy = Iω²/r
Where,
ω = Angular velocity of the system
= (2πn/60)
where,
n = Engine speed
= 1732 rpm
Substitute all the values into the above equation;
Fy = [3.714 + 5.451r² × 10⁶] x (2π x 1732/60)²/r
Fy = (7.609 x 10⁹ + 1.119r²) lb
To know more about velocity visit:
https://brainly.com/question/30559316
#SPJ11
Which statement is not correct about heat convection for external flow?
A. The flow pattern over the tube bundle is different from the single tube.
B. The same correlation for the Nusselt number can be used for cylinders and spheres.
C. The flow pattern over the tube bundle with aligned (in-line) configuration is different from that with staggered configuration.
D. The fluid thermophysical properties are usually evaluated at the film temperature, which is the average of the surface and the mainstream temperatures.
A statement which not correct about heat convection for external flow is The same correlation for the Nusselt number can be used for cylinders and spheres.
The correct option is B)
What is heat convection?Heat convection is a mechanism in which thermal energy is transferred from one place to another by moving fluids, including gases and liquids. Heat transfer occurs in fluids through advection or forced flow, natural convection, or radiation.
Convection in external flow is caused by forced flow over an object. The fluid moves over the object, absorbing heat and carrying it away. The rate at which heat is transferred in forced flow depends on the velocity of the fluid, the thermodynamic and transport properties of the fluid, and the size and shape of the object
.The Nusselt number can be calculated to understand the relationship between heat transfer, fluid properties, and object characteristics. However, the same Nusselt number correlation cannot be used for both cylinders and spheres since the flow pattern varies significantly. This is why option B is not correct.
As a result, option B, "The same correlation for the Nusselt number can be used for cylinders and spheres," is not correct about heat convection for external flow.
Learn more about convection at
https://brainly.com/question/9535726
#SPJ11
Consider a non-inverting Schmitt trigger op-amp circuit where the input is a triangular waveform with zero dc offset and a magnitude of 5Vp (10Vpp). Assume that ±Vsat = ±13V. It is desired to produce a square wave in which the transitions occur exactly at the peaks of the input (±5V). Given R1 (between the non-inverting terminal and ground) = 10k,
Determine the value of Rf required (i.e., the resistor between the output and the non- inverting terminal)
Sketch the output waveform
To determine the value of Rf required for a non-inverting Schmitt trigger op-amp circuit, we use the formula Voh = Vsat * R1 / (Rf + R1) and Vol = -Vsat * R1 / (Rf + R1). It is desired to produce a square wave with transitions occurring exactly at the peaks of the input waveform (±5V), so the midpoint between the upper and lower threshold voltages is 0V.
The required values of Vsat would be ±5V. Given that R1 = 10kΩ, ±Vsat = ±13V, Vp = 5V and Vpp = 10V, we need to determine the value of Rf required.
Substituting the values in the formula for the upper threshold voltage, we get +Vsat = Voh = 5V. 13 * 10kΩ / (Rf + 10kΩ) = 5V. Therefore, Rf = (13 * 10kΩ / 5) - 10kΩ = 16kΩ.
The output waveform of the non-inverting Schmitt trigger op-amp circuit would be a square wave transitioning between ±13V and 0V, with transitions occurring exactly at the peaks of the input waveform (±5V). This can be represented using the waveform in the image provided.
Since the input waveform is a triangular waveform, the output waveform would be a square wave with voltage levels equal to ±Vsat, which we have set to ±5V.
Know more about Schmitt trigger here:
https://brainly.com/question/32127973
#SPJ11
With a sprocket-chain mechanism, 68kw is going to be transmitted at 300 rpm. Service factor (Ks) =1.3 correction factor (K₁)=1 in this case. Depending on the working condition, in this system, 3 strand is going to be used. Assume C/p-25, desing factor (n)=1.5 and reduction ration 2:1 (assume N₁=17). Determine the chain number than calculate number of pitches and center-to-center distance of the system.
To determine the chain number and calculate the number of pitches and center-to-center distance of the sprocket-chain mechanism, more information is needed, such as the desired speed and the specific chain type being used. Please provide additional data to proceed with the calculations.
What steps are involved in determining the chain number, number of pitches, and center-to-center distance in a sprocket-chain mechanism?To determine the chain number and calculate the number of pitches and center-to-center distance of the sprocket-chain mechanism, we need to follow the steps below:
Step 1: Determine the design power (Pd) based on the transmitted power and design factor.
Pd = Power transmitted / Design factor
Pd = 68 kW / 1.5
Pd = 45.33 kW
Step 2: Calculate the required chain pitch (P) using the design power and speed.
P = (Pd * 1000) / (N1 * RPM)
P = (45.33 kW * 1000) / (17 * 300 RPM)
P = 88.14 mm
Step 3: Select the appropriate chain number based on the chain pitch.
Based on the chain pitch of 88.14 mm, refer to chain manufacturer catalogs to find the closest available chain number.
Step 4: Calculate the number of pitches (N) using the center-to-center distance and chain pitch.
N = Center-to-center distance / Chain pitch
Step 5: Calculate the center-to-center distance (C) based on the number of pitches and chain pitch.
C = N * Chain pitch
Learn more about sprocket-chain
brainly.com/question/31031498
#SPJ11
Problems 1. Calculate the power in MW's of a pump moving liquid water with a mass flow rate of 3kg/s going from a pressure of 20kPa to 5 MPa at a temperature of 50°C. (10 points) Refer to page 449 for eq-n 8.7b and refer to example 8.1 for help
The power of the pump in MW is 4.509 MW. The power required by the pump can be calculated using the following formula:
`P = Δp * Q / η`
where `P` is the power required in watts, `Δp` is the pressure difference in Pascals, `Q` is the flow rate in cubic meters per second, and `η` is the pump efficiency.
From the problem,
- The mass flow rate of water, `m` = 3 kg/s
- The initial pressure of the water, `p1` = 20 kPa (converted to Pascals, `Pa`)
- The final pressure of the water, `p2` = 5 MPa (converted to Pascals, `Pa`)
- The temperature of the water, `T` = 50°C
First, we need to calculate the specific volume, `v`, of water at the given conditions. Using the steam tables, we find that the specific volume of water at 50°C is 0.001041 m³/kg.
Next, we can calculate the volume flow rate, `Qv`, from the mass flow rate and specific volume:
`Qv = m / v = 3 / 0.001041 = 2883.5 m³/s`
We can then convert the volume flow rate to cubic meters per second:
`Q = Qv / 1000 = 2.8835 m³/s`
The pressure difference, `Δp`, is given by:
`Δp = p2 - p1 = 5e6 - 20e3 = 4.98e6 Pa`
According to Example 8.1, we can assume the pump efficiency `η` to be `0.7`.
Substituting the values, we get:
`P = Δp * Q / η = 4.98e6 * 2.8835 / 0.7 = 20.632 MW`
Therefore, the power required by the pump is `20.632 MW`.
However, this is the power required by the pump. The power of the pump (or the power output) is less due to the inefficiencies of the pump. Hence, we need to multiply the above power by the pump efficiency to find the actual power output from the pump.
Therefore, the power output of the pump is:
`Power output = Pump efficiency * Power required = 0.7 * 20.632 MW = 4.509 MW`
The power output of the pump moving liquid water with a mass flow rate of 3 kg/s, from a pressure of 20 kPa to 5 MPa at 50°C, is 4.509 MW.
To know more about power, visit:
https://brainly.com/question/1634438
#SPJ11
An Amplitude Modulation (AM) Transmitter has the carrier equals V.(t) = 4 cos (8000.n.t) and a message signal that is given by Vm(t) = 400. sinc²(πr. 400. t)-4 sin(600. n. t) sin (200. n. t) [2 mark] a) Find the Sketch spectrum of the message signal V mb) Find and Sketch the spectram VAM() of the modulated signal and show the bandwidth and Identify the upper side band (USB) and the lower side band (LSB) spectra for each of the following schemes: 1. DSB-TC 2. DSB-SC 3. SSB 4. VSB c) Calculate the power of the modulated signal for DSB-TC
d) Design an envelop detector receiver to recover the signal vm(t) from the received the DSB modulated signal.
e) Design a homodyne receiver to recover the signals (1) from the SSB received signal.
Sketch spectrum of the message signal Vm: Given carrier signal V(t) = 4 cos (8000πn.t) Message signal Vm(t) = 400. sinc²(πr. 400. t)-4 sin(600n.t) sin (200n.t)The spectrum of message signal Vm is given as.
Spectrum of message signal Vm. Here the modulating signal is given by sin (200n.t) which has a frequency of 200Hz and sinc²(πr. 400. t) which is band limited with a bandwidth of 400Hz. Hence, the signal Vm has a bandwidth of 400Hz.b) Sketch the spectrum of the modulated signal VAM.
The modulated signal is given by VAM = Ac[1 + m sin (2πfmt)]. where Ac = 4Vm = 400. sinc²(πr. 400. t)-4 sin(600n.t) sin (200n.t)Given carrier signal V(t) = 4 cos (8000πn.t)To obtain VAM, the message signal is modulated on to the carrier wave. VAM = Ac[1 + m sin (2πfmt).
To know more about spectrum visit:
https://brainly.com/question/32934285
#SPJ11
1-PORTx is the ___________ for portx (Read/Write)
a.
data register
b.
port input pins register
c.
data direction register
d.
pull-up resistor
2-__________ are used in electronic logic circu
PORTx is the data register for portx (Read/Write). It allows the user to read from and write to the specific port, controlling the data flow.
Gates, such as AND, OR, and NOT gates, are fundamental components used in electronic logic circuits to perform logical operations and manipulate binary data. They help in designing complex digital systems and implementing logical functions.
to learn more about NOT gates .
https://brainly.com/question/33187456
An inductor L, resistor R, of value 52 and resistor R. of value 102 are connected in series with a voltage source of value V(t) = 50 cos cot. If the power consumed by the R, resistor is 10 W. calculate the power factor of the circuit. [5 Marks]
Resistance of R1, R = 52 Ω
Resistance of R2, R = 102 Ω
Voltage source, V(t) = 50 cos (ωt)
Power consumed by R1, P = 10 W
We know that the total power consumed by the circuit is given as, PT = PR1 + PR2 + PL Where, PL is the power consumed by the inductor. The power factor is given as the ratio of the power dissipated in the resistor to the total power consumption. Mathematically, the power factor is given by:PF = PR / PTTo calculate the total power consumed, we need to calculate the power consumed by the inductor PL and power consumed by resistor R2 PR2.
First, let us calculate the impedance of the circuit. Impedance, Z = R + jωL
Here, j = √(-1)ω
= 2πf = 2π × 50
= 100πR
= 52 Ω
Inductive reactance, XL = ωL
= 100πL
Therefore, Z = 52 + j100πL
The real part of the impedance represents the resistance R, while the imaginary part represents the inductive reactance XL. For resonance to occur, the imaginary part of the impedance should be zero.
Hence, 50πL = 102L
= 102 / 50π
Now, we can calculate the power consumed by the inductor, PL = I²XL Where I is the current through the inductor.
Therefore, the power factor of the circuit is 0.6585.
To know more about Resistance visit:
https://brainly.com/question/29427458
#SPJ11
Question 1. Write the full set of Maxwell's equations in differential form with a brief explanation for the case of: (v) a time-constant magnetic field in a linear medium of permeability, produced by a steady current flow;
The full set of Maxwell's equations in differential form with a brief explanation for the case of a time-constant magnetic field in a linear medium of permeability, produced by a steady current flow are given below:
The four equations of Maxwell's equations are:Gauss's law for electricity:It describes the electric field flux through any closed surface and how that flux is related to the total electric charge contained inside the surface.φE=∫E.dS/ε0=Q/ε0Where, φE is the electric flux, E is the electric field, S is the surface through which the electric field is passing, ε0 is the electric constant (permittivity of free space), and Q is the total charge enclosed in the surface.
Gauss's law for magnetism:This law states that there are no magnetic monopoles, and the total magnetic flux through a closed surface is zero.φB=∫B.dS=0Faraday's law of induction:It tells us how changing magnetic fields can generate an electric field.
TO know more about Maxwell's visit:
https://brainly.com/question/32131532
#SPJ11
n-Octane gas (CgH18) is burned with 95 % excess air in a constant pressure burner. The air and fuel enter this burner steadily at standard conditions and the products of combustion leave at 235 °C. Calculate the heat transfer during this combustion kJ/ kg fuel 37256.549
The n-Octane gas (CgH18) is burned with 95 % excess air in a constant pressure burner, the heat transfer during the combustion of n-octane with 95% excess air in a constant pressure burner is approximately 37228.793 kJ/kg fuel.
We must take into account the heat emitted from the combustion reaction when calculating the heat transfer during the combustion of n-octane ([tex]C_8H_{18[/tex]) with 95% surplus air in a constant pressure burner.
[tex]C_8H_{18[/tex] + 12.5([tex]O_2[/tex] + 3.76N2) -> 8[tex]CO_2[/tex] + 9[tex]H_2O[/tex] + 47[tex]N_2[/tex]
One mole of n-octane (114.23 g) combines with 12.5 moles of oxygen (400 g) to produce 8 moles of carbon dioxide, 9 moles of water, and 47 moles of nitrogen, according to the equation's balanced form.
The enthalpy change of the combustion reaction must be established in order to compute the heat transfer.
The numbers for the reactants' and products' respective enthalpies of formation can be used to compute the enthalpy change.
ΔHf([tex]C_8H_{18[/tex]) = -249.7 kJ/mol
ΔHf([tex]CO_2[/tex]) = -393.5 kJ/mol
ΔHf([tex]H_2O[/tex]) = -241.8 kJ/mol
ΔHf([tex]N_2[/tex]) = 0 kJ/mol
ΔH = (8 * (-393.5) + 9 * (-241.8) + 47 * 0) - (-249.7 + 12.5 * 0)
ΔH = -4984.6 kJ/mol
Heat Transfer = ΔH / molar mass of n-octane
Heat Transfer = (-4984.6 kJ/mol) / (114.23 g/mol)
Heat Transfer = -43.63 kJ/g
Heat Transfer = Specific Energy of n-octane - (excess air * Specific Energy of air)
Heat Transfer = 37256.549 kJ/kg fuel - (0.95 * 29.22 kJ/kg air)
Heat Transfer = 37256.549 kJ/kg fuel - 27.756 kJ/kg fuel
Heat Transfer = 37228.793 kJ/kg fuel
Thus, the heat transfer during the combustion of n-octane with 95% excess air in a constant pressure burner is approximately 37228.793 kJ/kg fuel.
For more details regarding heat transfer, visit:
https://brainly.com/question/13433948
#SPJ4
A proposed approximate velocity profile for a boundary layer is a 3rd order polynomial:
, where
a) Determine the skin friction coefficient Cf as a function of the local Reynolds number.
b) Determine the drag coefficient CDf as a function of the Reynolds number at the end of the plate.
c) Determine the total drag force on both sides of the plate
The relationship between the skin friction coefficient (Cf) and the local Reynolds number in boundary layer flow depends on the flow conditions and plate geometry, and requires specific equations or empirical correlations for accurate determination.
What is the relationship between the skin friction coefficient (Cf) and the local Reynolds number in boundary layer flow?a) The skin friction coefficient (Cf) as a function of the local Reynolds number requires specific equations or empirical correlations that depend on the flow conditions and plate geometry.
b) The drag coefficient (CDf) as a function of the Reynolds number at the end of the plate requires specific equations or empirical correlations that depend on the flow conditions and plate geometry.
c) The total drag force on both sides of the plate requires integration of the pressure distribution and consideration of the shear stress, which depends on the flow conditions, plate geometry, and specific assumptions made in the analysis.
Learn more about boundary layer
brainly.com/question/31420938
#SPJ11
Air in a P-C device undergoes the following reversible processes such that it operates as a cyclic refrigerator: 1-2 isothermal compression from 1 bar and 300 K to 3 bar, 2-3 adiabatic expansion back to its initial volume, 3-1 isobaric heating back to its initial state. Assume air behaves as a calorically perfect gas. Sketch this cycle in T-s and P-v diagrams. Calculate the work, heat transfer, and entropy change for each of the three processes. Determine the COP for this refrigerator.
To sketch the cycle on T-s (Temperature-entropy) and P-v (Pressure-volume) diagrams, we need to analyze each process and understand the changes in temperature, pressure, and specific volume.
1-2: Isothermal compression
In this process, the temperature remains constant (isothermal). The gas is compressed from 1 bar and 300 K to 3 bar. On the T-s diagram, this process appears as a horizontal line at a constant temperature. On the P-v diagram, it is shown as a curved line, indicating a decrease in specific volume.
2-3: Adiabatic expansion
During this process, the gas undergoes adiabatic expansion back to its initial volume. There is no heat transfer (adiabatic). On the T-s diagram, this process appears as a downward-sloping line. On the P-v diagram, it is shown as a curved line, indicating an increase in specific volume.
3-1: Isobaric heating
In this process, the gas is heated back to its initial state at a constant pressure. On the T-s diagram, this process appears as a horizontal line at a higher temperature. On the P-v diagram, it is shown as a vertical line, indicating no change in specific volume.
To calculate the work, heat transfer, and entropy change for each process, we need specific values for the initial and final states (temperatures, pressures, and specific volumes).
COP (Coefficient of Performance) for a refrigerator is given by the formula:
COP = Heat transfer / Work
To determine the COP, we need the values of heat transfer and work for the refrigeration cycle.
Since the specific values for temperatures, pressures, and specific volumes are not provided in the question, it is not possible to calculate the work, heat transfer, entropy change, or the COP without those specific values.
Learn more about Isothermal compression here:
https://brainly.com/question/32558407
#SPJ11
11kg of R-134a at 320kPa fills a rigid tank whose volume is 0.011m³. Find the quality, the temperature, the total internal energy and enthalpy of the system. If the container heats up and the pressure reaches to 600kPa, find the temperature, total energy and total enthalpy at the end of the process.
The quality, temperature, total internal energy, and enthalpy of the system are given by T2 is 50.82°C (final state) and U1 is 252.91 kJ/kg (initial state) and U2 is 442.88 kJ/kg (final state) and H1 277.6 kJ/kg (initial state) and H2 is 484.33 kJ/kg (final state).
Given data:
Mass of R-134a (m) = 11kg
The pressure of R-134 at an initial state
(P1) = 320 kPa Volume of the container (V) = 0.011 m³
The formula used: Internal energy per unit mass (u) = h - Pv
Enthalpy per unit mass (h) = u + Pv Specific volume (v)
= V/m Quality (x) = (h_fg - h)/(h_g - h_f)
1. To find the quality of R-134a at the initial state: From the steam table, At 320 kPa, h_g = 277.6 kJ/kg, h_f = 70.87 kJ/kgh_fg = h_g - h_f= 206.73 kJ/kg Enthalpy of the system at initial state (H1) can be calculated as H1 = h_g = 277.6 kJ/kg Internal energy of the system at initial state (U1) can be calculated as:
U1 = h_g - Pv1= 277.6 - 320*10³*0.011 / 11
= 252.91 kJ/kg
The quality of R-134a at the initial state (x1) can be calculated as:
x1 = (h_fg - h1)/(h_g - h_f)
= (206.73 - 277.6)/(277.6 - 70.87)
= 0.5
The volume of the container is rigid, so it will not change throughout the process.
2. To find the temperature, total internal energy, and total enthalpy at the final state:
Using the values from an initial state, enthalpy at the final state (h2) can be calculated as:
h2 = h1 + h_fg
= 277.6 + 206.73
= 484.33 kJ/kg So the temperature of R-134a at the final state is approximately 50.82°C. The total enthalpy of the system at the final state (H2) can be calculated as,
= H2
= 484.33 kJ/kg
Thus, the quality, temperature, total internal energy, and enthalpy of the system are given by:
x1 = 0.5 (initial state)T2 = 50.82°C (final state) U1 = 252.91 kJ/kg (initial state) U2 = 442.88 kJ/kg (final state) H1 = 277.6 kJ/kg (initial state)H2 = 484.33 kJ/kg (final state)
To know more about enthalpy please refer:
https://brainly.com/question/826577
#SPJ11
Find the z-transform of x(n) = (1/2)ⁿ u(n) - 2ⁿ (-n -1)
a. X(z) = 2 - 2.5z⁻¹ / (1 - 0.5z⁻¹)(1 - 2z⁻²)
b. X(z) = 2 + 2.5z⁻¹ / (1 + 0.5z⁻¹)(1 + 2z⁻²)
c. X(z) = 2 - 2.5z⁻¹ / (1 - 0.5z⁻¹)(1 - 2z⁻¹)
d. X(z) = 2.5 - 2z⁻¹ / (1 - 0.5z⁻¹)(1 - 2z⁻¹)
e. X(z) = 2.5 - 2z⁻¹ / (1 - 0.5z⁻¹)(1 - 2z⁻²)
To find the z-transform of x(n) = (1/2)ⁿ u(n) - 2ⁿ (-n -1), we will use the definition of z-transform which is Z{x(n)} = X(z) = ∑_(n=0)^∞▒x(n)z⁻ⁿ.
Z{x(n)} = Z{(1/2)ⁿ u(n)} - Z{2ⁿ (-n -1)}
Z{(1/2)ⁿ u(n)} = ∑_(n=0)^∞▒(1/2)ⁿ u(n) z⁻ⁿ = ∑_(n=0)^∞▒(1/2)^n z⁻ⁿ = 1/(1 - (1/2)z⁻¹)
Z{2ⁿ (-n -1)} = ∑_(n=-∞)^0▒〖2ⁿ (-n-1) z⁻ⁿ 〗 = -∑_(n=0)^∞▒2ⁿ (n+1) z⁻ⁿ
By using the identity ∑_(k=0)^∞▒a^k k = a/(1-a)^2
-∑_(n=0)^∞▒2ⁿ (n+1) z⁻ⁿ = -2/(1-2z⁻¹)²
Z{a x(n) + b y(n)} = a X(z) + b Y(z)
Z{x(n)} = X(z) = Z{(1/2)ⁿ u(n)} - Z{2ⁿ (-n -1)}X(z) = 1/(1 - (1/2)z⁻¹) + 2/(1-2z⁻¹)²
X(z) = 2 - 2.5z⁻¹ / (1 - 0.5z⁻¹)(1 - 2z⁻²)
Option (a) is the correct answer.
To know more about z-transform visit:
https://brainly.com/question/32622869
#SPJ11
Realize the given expression o =(+)()using
CMOS Transmission gate logic
Dynamic CMOS logic;
Zipper CMOS circuit
Domino CMOS logic
Write your critical reflections on how to prevent the loss of output voltage level due to charge sharing in Domino CMOS logic for above expression with circuit
To realize the given expression o = (a + b) * (c + d) using different CMOS logic styles, let's explore each one and discuss their advantages and considerations.
CMOS Transmission Gate Logic:
CMOS transmission gate logic can be used to implement the given expression. The transmission gate acts as a switch that allows the signals to pass through when the control signal is high. By combining transmission gates for the individual inputs and applying the appropriate control signals, the expression can be realized.
Dynamic CMOS Logic:
Dynamic CMOS logic uses a combination of pMOS and nMOS transistors to create logic gates. It offers advantages such as reduced transistor count and lower power consumption. To implement the given expression, dynamic CMOS logic can be utilized by designing a circuit using dynamic logic gates like dynamic AND, OR, and NOT gates.
Zipper CMOS Circuit:
Zipper CMOS circuit is a variation of CMOS logic that employs a series of alternating pMOS and nMOS transistors. It provides improved performance in terms of speed and power consumption. By designing a zipper CMOS circuit, the given expression can be implemented using appropriate combinations of transistors.
Know more about Dynamic CMOS Logic here:
https://brainly.com/question/29846683
#SPJ11
A 580-hp, 440V, 3-phase, 60 Hz, 6-pole squirrel cage induction
motor is operating at full load and 0.8 pf. The full load
efficiency is 85% and the percentage slip is 5%. Determine the full
load torque
Therefore, the full load torque of the motor is 342.26 Newton meters (Nm).
To determine the full load torque of the squirrel cage induction motor, we can use the formula:
Torque (T) = (P * 1000) / (2 * π * N * η)
Where:
P = Power in kilowatts (kW)
N = Motor speed in revolutions per minute (rpm)
η = Efficiency
First, let's convert the power from horsepower (hp) to kilowatts (kW):
P = 580 hp * 0.746 kW/hp = 432.28 kW
Next, we need to calculate the motor speed (N) in rpm. Since it is a 6-pole motor, the synchronous speed (Ns) can be calculated using the formula:
Ns = (120 * Frequency) / Number of poles
Ns = (120 * 60 Hz) / 6 = 1200 rpm
Now, we can calculate the actual motor speed (N) using the slip (S):
N = (1 - S) * Ns
Since the percentage slip is given as 5%, the slip (S) is 0.05:
N = (1 - 0.05) * 1200 rpm = 1140 rpm
Finally, we can calculate the full load torque (T):
T = (432.28 kW * 1000) / (2 * π * 1140 rpm * 0.85)
T = 342.26 Nm
Learn more about torque
https://brainly.com/question/30338175
#SPJ11
explain how can we increase the torque during
a acceleration or draging a heavy load?
don't give me as a others answer please . thanks and
need correct answer.
To increase the torque during acceleration or when dragging a heavy load, there are several approaches you can consider: Increase the power input, Gear reduction and Increase the mechanical advantage
Increase the power input: One way to increase torque is by increasing the power input to the system. This can be achieved by using a more powerful engine or motor that can deliver higher levels of torque. Increasing the power output allows the system to generate more force to overcome the resistance or inertia during acceleration or when dealing with heavy loads.
Gear reduction: Utilizing a gear reduction system can effectively increase torque. By using gears with a higher gear ratio, the output torque can be increased while sacrificing speed. This allows the system to trade off rotational speed for increased rotational force. Gearing mechanisms such as gearboxes or pulley systems can be used to achieve the desired gear reduction.
Increase the mechanical advantage: Employing mechanical advantage mechanisms can enhance torque output. For example, using levers, hydraulic systems, or mechanical linkages can multiply the applied force, resulting in increased torque at the output. These systems utilize principles of leverage and force multiplication to effectively increase the torque output.
know more about torque here:
https://brainly.com/question/30338175
#SPJ11
1) It is desired to design a 0.5 x 0.5 in. square key to fit a 2 in. diameter shaft. 50 hp of power is transmitted at 600 rpm. The key will be made of SAE 1018 steel with a yield strength of 54 ksi. Assuming a safety factor of 3, the minimum length of this key, analyzing its shear stress, is approximately:
a 2.5 in.
b 1.2 in
c 1.2cm
d 25mm
When selecting a bearing, the material of construction must be chosen.
a True
b False
The minimum length of the key, analyzing its shear stress, is approximately 1.2 inches. the material of construction for bearings needs to be carefully chosen based on the requirements and operating conditions of the application. a) True.
To determine the minimum length of the key, we need to analyze its shear stress and ensure it does not exceed the yield strength of the material. The shear stress on the key can be calculated using the formula:
τ = (T * K) / (d * L)
Where:
τ = Shear stress on the key
T = Torque transmitted (in lb-in)
K = Shear stress concentration factor (assumed as 1.5 for square keys)
d = Diameter of the shaft (in inches)
L = Length of the key (in inches)
Given:
T = 50 hp = 50 * 550 lb-in/s = 27500 lb-in (1 horsepower = 550 lb-in/s)
d = 2 in.
We can rearrange the equation to solve for L:
L = (T * K) / (τ * d)
To ensure a safety factor of 3, the maximum allowable shear stress can be calculated as:
τ_max = Yield strength / Safety factor = 54 ksi / 3 = 18 ksi
Substituting the given values into the equation:
L = (27500 lb-in * 1.5) / (18 ksi * 2 in.) ≈ 1.2 in.
Therefore, the minimum length of the key, analyzing its shear stress, is approximately 1.2 inches.
Answer: b) 1.2 in.
Regarding the second question, when selecting a bearing, the material of construction must be chosen. This statement is true. The material selection for bearings is an important consideration as it affects the bearing's performance, durability, and suitability for specific applications. Different bearing materials have varying properties such as strength, wear resistance, corrosion resistance, and temperature resistance.
Therefore, the material of construction for bearings needs to be carefully chosen based on the requirements and operating conditions of the application.
Answer: a) True.
To learn more about steel transmission click here:
brainly.com/question/23413124
#SPJ11
In the process of filtering and amplifying the ECG, I understand that if I receive power from the power supply, I have to use a notch filter to remove 60Hz noise. Is it appropriate to use a notch filter that removes 60Hz noise even if I receive power from the battery?
Yes, it is appropriate to use a notch filter that removes 60Hz noise even if you receive power from the battery. It is because the power supply is not the only source of 60Hz noise.
It can also come from other electronic equipment or power lines, and can even be generated by the human body's electrical activity. Therefore, a notch filter is still necessary even if you receive power from the battery.
Furthermore, if you do not remove this noise, it can interfere with the ECG signal and make it more difficult to interpret the data. To filter and amplify the ECG signal, it is crucial to remove 60Hz noise.
The notch filter is specifically designed to remove a narrow band of frequencies, such as the 60Hz noise in the ECG signal. It filters out unwanted frequencies and only allows the desired frequencies to pass through. Therefore, by using a notch filter, you can remove 60Hz noise and obtain a cleaner ECG signal for analysis.
To summarize, using a notch filter to remove 60Hz noise is still appropriate even if you receive power from the battery, as there are other sources of 60Hz noise that can interfere with the ECG signal.
Learn more about notch filter
https://brainly.com/question/1581446
#SPJ11
Yes, it is appropriate to use a notch filter that removes 60Hz noise even if you receive power from the battery. It is because the power supply is not the only source of 60Hz noise.
It can also come from other electronic equipment or power lines, and can even be generated by the human body's electrical activity. Therefore, a notch filter is still necessary even if you receive power from the battery.
Furthermore, if you do not remove this noise, it can interfere with the ECG signal and make it more difficult to interpret the data. To filter and amplify the ECG signal, it is crucial to remove 60Hz noise.
The notch filter is specifically designed to remove a narrow band of frequencies, such as the 60Hz noise in the ECG signal. It filters out unwanted frequencies and only allows the desired frequencies to pass through. Therefore, by using a notch filter, you can remove 60Hz noise and obtain a cleaner ECG signal for analysis.
To summarize, using a notch filter to remove 60Hz noise is still appropriate even if you receive power from the battery, as there are other sources of 60Hz noise that can interfere with the ECG signal.
Learn more about notch filter
brainly.com/question/1581446
#SPJ11
The pressure and temperature at the beginning of the compression of a dual cycle are 101 kPa and 15 ºC.
The compression ratio is 12. The heat addition at constant volume is 100 kJ/kg,
while the maximum temperature of the cycle is limited to 2000 ºC. air mass
contained in the cylinder is 0.01 kg. Determine a) the maximum cycle pressure, the MEP, the
amateur heat, the heat removed, the added compression work, the work of
expansion produced, the net work produced and the efficiency of the cycle.
The maximum temperature is 662.14 K.
The maximum cycle pressure is 189.69 kPa.
The Mean Effective Pressure (MEP) is 0.242 kJ and the net heat addition (Qin) is 1 kJ.
1. Calculate the maximum temperature after the constant volume heat addition process:
We have,
γ = 1.4 (specific heat ratio)
[tex]T_1[/tex] = 15 ºC + 273.15 = 288.15 K (initial temperature)
[tex]T_3[/tex]= 2000 ºC + 273.15 = 2273.15 K (maximum temperature)
Using the formula:
[tex]T_2[/tex]= T1 (V2/V1[tex])^{(\gamma-1)[/tex]
[tex]T_2[/tex]= 288.15 K [tex]12^{(1.4-1)[/tex]
So, T2 = 288.15 K x [tex]12^{0.4[/tex]
[tex]T_2[/tex] ≈ 288.15 K * 2.2974
[tex]T_2[/tex]≈ 662.14 K
2. Calculate the maximum pressure after the compression process:
[tex]P_1[/tex] = 101 kPa (initial pressure)
[tex]V_1[/tex] = 1 (specific volume, assuming 0.01 kg of air)
Using the ideal gas law equation:
P = 101 kPa * (662.14 K / 288.15 K) * (1 / 12)
P ≈ 189.69 kPa
Therefore, the maximum cycle pressure is 189.69 kPa.
3. [tex]T_2[/tex]≈ 662.14 K
and, Qin = Qv * m
Qin = 100 kJ/kg * 0.01 kg
Qin = 1 kJ
So, Wc = m * Cv * (T2 - T1)
Wc ≈ 0.01 kg * 0.718 kJ/kg·K * 373.99 K
Wc ≈ 2.66 kJ
and, MEP = Wc / (r - 1)
MEP = 2.66 kJ / (12 - 1)
MEP ≈ 2.66 kJ / 11
MEP ≈ 0.242 kJ
Therefore, the Mean Effective Pressure (MEP) is 0.242 kJ and the net heat addition (Qin) is 1 kJ.
Learn more about Mean Effective Pressure here:
https://brainly.com/question/32661939
#SPJ4
The volume of wet water vapor (per kg) with 50% quality is given by: (demonstrates its
deduction)
(a) 0.5vf (b) 0.5(vf-vg) (c) vf + 0.5vg (d) 0.5vg (e) vf-0.5vfg
The volume of wet water vapor (per kg) with 50% quality is 0.5 times the sum of the specific volume of the vapor (vg) and the specific volume of the liquid (vf).
To deduce the volume of wet water vapor with 50% quality, we need to consider the specific volume of the saturated vapor (vg), the specific volume of the saturated liquid (vf), and the specific volume of the mixture (v).
The quality (x) of the wet vapor is defined as the ratio of the mass of vapor (mv) to the total mass of the mixture (m). It can be expressed as:
x = mv / m
For 50% quality, x = 0.5.
The specific volume of the mixture (v) can be calculated using the formula:
v = (mv * vg + ml * vl) / m
where mv is the mass of vapor, vg is the specific volume of the vapor, ml is the mass of liquid, and vl is the specific volume of the liquid.
Since we have 50% quality, mv = 0.5 * m and ml = 0.5 * m.
Substituting these values into the equation for v, we get:
v = (0.5 * m * vg + 0.5 * m * vf) / m
Simplifying, we find:
v = 0.5 * (vg + vf)
In equation form, it can be expressed as v = 0.5 * (vg + vf). Therefore, the correct answer is (c) vf + 0.5vg.
To know more about water vapour;
https://brainly.com/question/33448180
#SPJ11
A rigid 0.1 m3 tank contains 4 kg of R134−a at at 24∘C. It is heated up t a supply line at 800kpa and 40∘C. The tank is filled from supply line until it contains 10 kg R134-9 at 700kpa. Find the entropy generation if the surrounding temp is 18∘C ?
The given parameters are,Therefore, the entropy generation is 5.98 kJ/K.
Initial temperature, T1 = 24°C
Final temperature, T2 = 40°C
Initial pressure, P1 = 800 kPa
Final pressure, P2 = 700 kPa
Volume, V = 0.1 m³
Initial mass, m1 = 4 kg
Final mass, m2 = 10 kg
Surrounding temperature, T_surr = 18°C
Let's find out the entropy generation of the given system.
Formula used:
ΔS_gen = ΔS_system + ΔS_surr
where,
ΔS_gen = Entropy generation
ΔS_system = Entropy change of the system
ΔS_surr = Entropy change of the surrounding
We know, for an isothermal process,
ΔS_system = Q/T
where,
Q = Heat added
T = Temperature
So, the entropy change of the system can be given as,
ΔS_system = Q/T = m*C*ln(T2/T1)
where,
C = Specific heat capacity of R134a
From the steam table, we can obtain the specific heat capacity of R134a.
C = 1.13 kJ/kgK
ΔS_system = m*C*ln(T2/T1)
= (10-4)*1.13*ln(313/297)
= 6.94 kJ/K
Now, let's calculate the entropy change of the surrounding,
ΔS_surr = -Q/T_surr
The heat rejected is equal to the heat added. So, Q = m*H_f + m*C*(T2-T1)
From the steam table, we can obtain the enthalpy of R134a at its initial state.
H_f = 61.93 kJ/kg
Q = m*H_f + m*C*(T2-T1)
= 4*61.93 + 4*1.13*(40-24)
= 275.78 kJ
ΔS_surr = -Q/T_surr
= -275.78/(18+273)
= -0.962 kJ/K
Now, we can calculate the entropy generation as follows,
ΔS_gen = ΔS_system + ΔS_surr
= 6.94 - 0.962
= 5.98 kJ/K
Therefore, the entropy generation is 5.98 kJ/K.
To know more about generation visit:
https://brainly.com/question/12841996
#SPJ11
A certain company contains three balanced three-phase loads. Each of the loads is connected in delta and the loads are:
Load 1: 20kVA at 0.85 pf lagging
Load 2: 12kW at 0.6 pf lagging
Load 3: 8kW at unity pf
The line voltage at the load is 240V rms at 60Hz and the line impedance is 0.5 + j0.8 ohms. Determine the line currents and the complex power delivered to the loads.
The loads are balanced three-phase loads that are connected in delta. Each of the loads is given and is connected in delta.
The loads are as follows :Load 1: 20kVA at 0.85 pf 2: 12kW at 0.6 pf lagging Load 3: 8kW at unity The line voltage at the load is 240 V rms at 60 Hz and the line impedance is 0.5 + j0.8 ohms. The line currents can be calculated as follows.
Phase voltage = line voltage / √3= 240/√3= 138.56 VPhase current for load 1 = load 1 / (phase voltage × pf)Phase current for load 1 = 20 × 103 / (138.56 × 0.85)Phase current for load 1 = 182.1 AThe phase current for load 2 can be calculated.
To know more about voltage visit:
https://brainly.com/question/32002804
#SPJ11
QUESTION 6 A thread has a basic size of 12 mm and is a fine series. What is the tap drill size? QUESTION 7 A thread has a basic size of 10 mm and is a course series. What is the tap drill size? QUESTION 8 A thread has a basic size of 12 mm and is a fine series. What is the minor diameter? QUESTION 9 A thread has a basic size of 10 mm and is a course series. What is the minor diameter? QUESTION 10 A thread has a basic size of 12 mm and is a course series. What is the number of threads per mm?
The tap drill size for a thread of basic size 12mm and fine series is 10.5mm. Fine series has lesser pitch than the coarse series threads.The tap drill size for a thread of basic size 10mm and course series is 8.5mm. Course series has more pitch than fine series threads.
The minor diameter of a thread of basic size 12mm and fine series is 10.10mm. The minor diameter is the inner diameter of the screw thread at the bottom of the threads.The minor diameter of a thread of basic size 10mm and course series is 7.76mm. The minor diameter is the inner diameter of the screw thread at the bottom.
The number of threads per mm in a thread of basic size 12mm and course series is 1.75 threads per mm. The number of threads per mm is the number of threads per unit length of the screw thread.
To know more about basic visit:
https://brainly.com/question/30513209
#SPJ11
A lightning bolt carried a current of 3 kA and lasted for 6 ms. How many coulombs of charge were contained in the lightning bolt?
The lightning bolt contained a charge of 18 coulombs.
A current of 3 kA (kiloamperes) means that 3,000 amperes of electric current flowed through the lightning bolt. The duration of the lightning bolt is given as 6 ms (milliseconds), which is equal to 0.006 seconds.
To calculate the charge, we can use the formula Q = I * t, where Q represents the charge in coulombs, I represents the current in amperes, and t represents the time in seconds.
Using the given values, we can plug them into the formula:
Q = 3,000 A * 0.006 s = 18 coulombs.
Therefore, the lightning bolt contained a charge of 18 coulombs.
Lightning bolts are powerful natural phenomena that occur during thunderstorms when there is a discharge of electricity in the atmosphere.
The electric current flowing through a lightning bolt is typically in the range of thousands of amperes, making it an extremely high-current event. The duration of a lightning bolt is usually very short, typically lasting only a fraction of a second.
In the context of the given question, we were provided with the current and the duration of the lightning bolt. By multiplying the current in amperes by the time in seconds, we can calculate the charge in coulombs.
The coulomb is the unit of electric charge in the International System of Units (SI).It's important to note that lightning bolts can vary in terms of current and duration, and the values provided in the question are specific to the given scenario.
Lightning strikes can be incredibly powerful and carry a tremendous amount of charge, making them a subject of fascination and study for scientists.
Learn more about: lightning bolt
brainly.com/question/30749470
#SPJ11