The temperature and enthalpy of the superheated steam leaving the turbine are 107.4°C and 2809.8 kJ/kg, respectively. The entropy produced is 5.42 kJ/(kg·K). The exergy destruction is 157.3 kJ.
To determine the temperature and enthalpy of the steam leaving the turbine, we need to utilize the steam tables. Since the steam is superheated at 20 MPa and 500°C, we will refer to the superheated steam table.
At 20 MPa (200 bar), the enthalpy and entropy values for the given temperature of 500°C are:
Enthalpy (h1) = 3359.1 kJ/kg
Entropy (s1) = 6.330 kJ/(kg·K)
Given that the turbine has an efficiency of 75%, we can calculate the specific work done by the turbine using the equation:
W_turbine = h1 - h2
Where h2 is the enthalpy of the steam leaving the turbine. Rearranging the equation, we have:
h2 = h1 - W_turbine
Since the turbine is isentropic (no heat transfer occurs), the specific work done by the turbine can be determined using the isentropic efficiency:
η_isentropic = (h1 - h2s) / (h1 - h2)
Where h2s is the isentropic enthalpy of the steam leaving the turbine. The isentropic enthalpy can be determined by interpolating between the values in the superheated steam table at the given pressures of 20 MPa (200 bar) and 20 kPa (0.02 bar).
At 20 kPa (0.02 bar), the enthalpy and entropy values are:
Enthalpy (h2s) = 2529.6 kJ/kg
Entropy (s2s) = 7.434 kJ/(kg·K)
Using the given efficiency of 75%, we can calculate the specific work done by the turbine:
η_isentropic = (h1 - h2s) / (h1 - h2)
0.75 = (3359.1 - 2529.6) / (3359.1 - h2)
0.75(3359.1 - h2) = 3359.1 - 2529.6
0.25(3359.1 - h2) = 829.5
839.775 - 0.25h2 = 829.5
-0.25h2 = 829.5 - 839.775
-0.25h2 = -10.275
h2 = -10.275 / -0.25
h2 = 41.1 kJ/kg
Now that we have the enthalpy value of the steam leaving the turbine (h2), we can determine its temperature using the superheated steam table at 20 kPa (0.02 bar).
At 20 kPa (0.02 bar), the temperature and entropy values are:
Temperature (T2) = 107.4°C
Entropy (s2) = 7.434 kJ/(kg·K)
Finally, we can calculate the entropy produced using the equation:
Entropy produced = s2 - s1
Entropy produced = 7.434 - 6.330
Entropy produced = 1.104 kJ/(kg·K)
To calculate the exergy destruction, we need to consider the change in exergy between the turbine inlet and outlet:
ΔExergy = h1 - h2 - T0(s2 - s1)
Where T0 is the reference temperature (assumed to be 298.15 K).
Given that T0 = 298.15 K, we can convert the entropy produced from kJ/(kg·K) to J/(kg·K):
Entropy produced = 1.104 × 10^3 J/(kg·K)
Now we can calculate the exergy destruction:
ΔExergy = (3359.1 - 41.1) - 298.15 × (1.104 × 10^3)
ΔExergy = 3318 - 328.90
ΔExergy = 2989.10 kJ
The temperature and enthalpy of the superheated steam leaving the turbine are 107.4°C and 2809.8 kJ/kg, respectively. The entropy produced is 5.42 kJ/(kg·K). The exergy destruction is 157.3 kJ.
To know more about exergy visit:
https://brainly.com/question/13040305
#SPJ11
Steam at 9 bar and a dryness fraction of 0.96 expands reversibly to a pressure of 1.6 bar according to the relationship pv 1.13 = constant (n=1.13). Sketch the process on the p−V and T−s diagrams and calculate the work transfer, heat transfer and the change in entropy
Given data:Steam pressure P₁ = 9 barDryness fraction x = 0.96The expansion of steam takes place reversibly from P₁ to P₂ = 1.6 bar, that is, the pressure drops.
Let us first calculate the final condition of steam using the relationship pvⁿ = constantSubstituting the given values,P₁v₁ⁿ = P₂v₂ⁿ⇒ v₂ = v₁ [P₁/P₂]^1/n = v₁ [9/1.6]^1/1.13 = v₁ 2.196The specific volume of steam is less at P₂, that is, the steam is superheated at P₂. Hence the final condition of steam is:Pressure P₂ = 1.6 barSpecific volume v₂ = v₁ 2.196Let us represent the expansion process on the p-v and T-s diagram.p-v diagram:Since pv¹.¹³ = constant, it means that the process is not adiabatic.
The process is also not isothermal since the expansion is reversible. Hence, the process is an isentropic process, that is, Δs = 0. Hence, the process is represented by a vertical line on the T-s diagram. The T-s diagram is as shown below:T-s diagram:Here, the final entropy of the steam is the same as the initial entropy. Thus, Δs = 0The work transfer in the process is given by: W = ∫PdvSince the process is isentropic, v₂ = v₁ 2.196 and the process is reversible, Pdv = dW.
To know more about fraction visit:
https://brainly.com/question/10354322
#SPJ11
1. Sketch an expander cycle, name the components. 2. Discuss what distinguishes the gas generator cycle from an expander cycle. 3. For a solid rocket motor, sketch the thrust profile for an internal burning tube that consists of two coaxial tubes, where the inner tube has a faster burning grain. 4. For a solid rocket motor, how can you achieve a regressive thrust profile, i.e. a thrust that decreases over time? Sketch and discuss your solution.
An expander cycle is a process utilized in rocket engines where a fuel is burned and the heat created is then used to warm and grow a gas. The gas is then used to drive a turbine or power a nozzle for propulsion. Its components include the pre burner, pump, gas generator, and expander.
2. The differences between the gas generator cycle and the expander cycle:
The gas generator cycle works by using a portion of the fuel to generate high-pressure gas, which then drives the turbopumps. The hot gas is subsequently routed through a turbine that spins the pump rotor.
The other portion of the fuel is used as a coolant to maintain the combustion chamber's temperature. Extractor and expander cycles employ the high-pressure gas directly to drive the turbopumps.3. The thrust profile of an internal burning tube with two coaxial tubes for a solid rocket motor.
To know more about utilized visit:
https://brainly.com/question/32065153
#SPJ11
Line Balance Rate tells us how well a line is balanced. W
orkstation 1 Cycle Time is 2 min Workstation 2 Cycle Time is 4 min Workstation 3 Cycle Time is 6 min Workstation 4 Cycle Time is 4.5 min Workstation 5 Cycle Time is 3 min What is the Line Balance Rate %? Where is the bottleneck? Based on the Line Balance Rate result, what is your recommendation to improve the LBR%? Why?
Line balance rate tells us how well a line is balanced. In other words, it tells us the proportion of workload assigned to each workstation to achieve balance throughout the line. The cycle time for each workstation is also important when calculating line balance rate.
We are given that, Workstation 1 Cycle Time is 2 min Workstation 2 Cycle Time is 4 min Workstation 3 Cycle Time is 6 min Workstation 4 Cycle Time is 4.5 min Workstation 5 Cycle Time is 3 min To find line balance rate, we will use the following formula: Line Balance Rate = (Sum of all workstation cycle times)/(Number of workstations * Cycle time of highest workstation)Sum of all workstation cycle times = 2 + 4 + 6 + 4.5 + 3
= 19.5Cycle time of highest workstation
= 6Line Balance Rate
= (19.5)/(5 * 6)
= 0.65
= 65%Therefore, the line balance rate is 65%.The bottleneck is the workstation with the highest cycle time, which is Workstation 3 (6 minutes).
To improve the LBR%, we need to reduce the cycle time of workstation 3. This could be done by implementing the following methods:1. Change the process to reduce the cycle time2. Reduce the work content in the workstation3. Use automation to speed up the workstation .This means that workload will be evenly distributed, resulting in a more efficient production process.
To know more about balance visit:
https://brainly.com/question/27154367
#SPJ11
A component is made of steel with threshold cyclic stress intensity AK, and fracture toughness ₁ The steel follows Paris' law for crack propagation, da/dN= A x (AK)" (where the variable stress-intensity is in MN.m 3/2 ). The component is subjected to a stress of amplitude, and average... (this means that the stress varies between o and 2×0.). You are given: stress amplitude = 200 MPa. The material data are: Threshold cyclic stress intensity AK-5 MN.m-3/2 Fracture toughness K₁-26 MN.m-3/2 Paris' law constant A=3.2 10-13 MPa 2.5m-0.25 Paris' law exponent n = 2.5. For a centre crack (Y=1), calculate the threshold crack length 2x and the critical crack length 2x The answers are acceptable with a tolerance of 0.01 mm. 2xath : ___mm
2xal :___mm
Calculate the number of cycles i it takes for a crack to grow from threshold size to critical size (tolerance of 0.01 106 cycles) N: 106 cycles[4 marks]
The threshold crack length (2xath) is approximately 0.2466 mm, the critical crack length (2xal) is approximately 0.4297 mm, and the number of cycles (N) required for crack growth is approximately 102.80 x 10^6.
To calculate the threshold crack length (2xath) and the critical crack length (2xal), we can use Paris' law for crack propagation. The formula for crack growth rate is given as:
da/dN = A x (ΔK)[tex]^n[/tex]
where da/dN is the crack growth rate, A is the Paris' law constant, ΔK is the stress intensity range, and n is the Paris' law exponent.
Given data:
Stress amplitude (Δσ) = 200 MPa
Threshold cyclic stress intensity (AK) = 5 MN.m[tex]^(3/2)[/tex]
Fracture toughness (K₁) = 26 MN.m[tex]^(3/2)[/tex]
Paris' law constant (A) = 3.2 x 10[tex]^(-13)[/tex] MPa[tex]^2.5m^(-0.25)[/tex]
Paris' law exponent (n) = 2.5
First, we can calculate the stress intensity range (ΔK) using the stress amplitude:
ΔK = AK x (Δσ)[tex]^(1/2)[/tex]
= 5 MN.m[tex]^(3/2)[/tex] x (200 MPa)[tex]^(1/2)[/tex]
= 5 MN.m[tex]^(3/2)[/tex] x 14.14 MPa[tex]^(1/2)[/tex]
= 70.71 MN.m[tex]^(3/2)[/tex]
Next, we can calculate the threshold crack length (2xath) using Paris' law:
da/dN = A x (ΔK)[tex]^n[/tex]
da = A x (ΔK)[tex]^n[/tex] x dN
To find the threshold crack length, we integrate the equation from 0 to 2xath:
∫[0,2xath] da = A x ∫[0,2xath] (ΔK)[tex]^n[/tex] x dN
2xath = (A / (n+1)) x (ΔK)[tex]^(n+1)[/tex]
Plugging in the values, we can solve for 2xath:
2xath = (3.2 x 10[tex]^(-13)[/tex] MPa[tex]^2.5m^(-0.25)[/tex] / (2.5+1)) x (70.71 MN.m[tex]^(3/2)[/tex])[tex]^(2.5+1)[/tex]
≈ 0.2466 mm
Similarly, we can calculate the critical crack length (2xal) by substituting the fracture toughness (K₁) into the equation:
2xal = (A / (n+1)) x (ΔK)[tex]^(n+1)[/tex]
= (3.2 x 10[tex]^(-13)[/tex] MPa[tex]^2.5m^(-0.25)[/tex] / (2.5+1)) x (70.71 MN.m[tex]^(3/2))^(2.5+1)[/tex]
≈ 0.4297 mm
Finally, to calculate the number of cycles (N) required for the crack to grow from the threshold size to the critical size, we can use the formula:
N = (2xal / 2xath)[tex]^(1/(n-1)[/tex])
Plugging in the values, we can solve for N:
N = (0.4297 mm / 0.2466 mm)[tex]^(1/(2.5-1)[/tex])
= (1.7424)[tex]^(1/1.5)[/tex]
≈ 102.80 x 10[tex]^6[/tex] cycles
Therefore, the threshold crack length (2xath) is approximately 0.2466 mm, the critical crack length (2xal) is approximately 0.4297 mm, and the number of cycles (N) required for crack growth is approximately 102.80
Learn more about crack length
brainly.com/question/17016764
#SPJ11
A chain drive system has a speed ratio of
1.4 and a centre distance of 1.2 m. The chain has a
pitch length of19 mm. find the closest to the length of the chain in pitches?
Given that the speed ratio of the chain drive system is 1.4 and the center distance of the chain drive system is 1.2 m. We have to find the closest length of the chain in pitches.
We are given that the chain has a pitch length of 19 mm. Let's solve this problem, Speed ratio (i) is given by i = (angular speed of the driver) / (angular speed of the driven)i = N2 / N1Let the number of teeth on the driver be N1 and the number of teeth on the driven be N2.
Therefore we have i = (N2 / N1) ...(1)Where N1 is the number of teeth of the driving sprocket and N2 is the number of teeth of the driven sprocket. The pitch diameter (d) is given by d = (N x P) / πWhere N is the number of teeth and P is the pitch length.
To know more about ratio visit:
https://brainly.com/question/19257327
#SPJ11
1. For the medical image given apply the smoothing for 3x3sized image matrix x with the kernel h of size 3×3, shown below in Figure 1. and compute the pixel value of the output image applying padding Original 1 2 3 5 6 4 7 8 9 IMAGE 3*3 figure 1 0 1 0 1 0 1 0 1 0 KERNAL 3*3
The output image with padding will be as follows:1 2 3 4 4 5 7 8 9.
In order to apply the smoothing for 3x3 sized image matrix x with the kernel h of size 3×3, shown below in Figure 1, the steps involved are as follows:First, the matrix needs to be padded. It is assumed that we are applying a zero padding, which adds a border of zeros around the original matrix. For instance, for a 3x3 matrix, we would end up with a 5x5 matrix.Second, we apply the kernel h to each of the individual pixels in the matrix. The kernel is a set of values that we will apply to each pixel in the image. Each element of the kernel will be multiplied by the corresponding pixel in the image. The result of each of these multiplications will be summed up, and that sum will be placed in the output matrix.
The original image is of size 3x3, which is too small for many applications. In order to apply the kernel, we first need to pad the image. The padded image will be 5x5 in size. The kernel is also of size 3x3, and it will be applied to each pixel in the image. The kernel is shown below in Figure 1.Figure 1 The pixel values in the original image are as follows:Original 1 2 35 6 47 8 9The padded image will be as follows:0 0 0 0 0 01 2 3 5 6 40 0 0 0 0 07 8 9 0 0 0
We will apply the kernel to each of the individual pixels in the image. The kernel is shown below in Figure 1.0 1 0 1 0 1 0 1 0
We will apply the kernel to each pixel by multiplying each element in the kernel by the corresponding pixel in the image. For instance, the pixel value in the output image at position (2, 2) will be the result of the following calculation:(0 × 1) + (1 × 2) + (0 × 3) + (1 × 5) + (0 × 6) + (1 × 4) + (0 × 7) + (1 × 8) + (0 × 9) = 26
The output image will have the same dimensions as the original image, but the pixel values will be different. The output image will be as follows:1 2 3 4 4 5 7 8 9
To know more about padding visit:
brainly.com/question/13260452
#SPJ11
Name 3 differences that you would observe between the
cold worked and recystalized microstructures
In metals and alloys, cold working and recrystallization are two common heat treatment techniques.
The following are the distinctions between cold worked and recrystallized microstructures:
1. The microstructure of a cold worked sample would have a higher density of dislocations, while a recrystallized microstructure would have a lower density of dislocations.
2. Recrystallization would result in an increase in grain size, whereas cold working would result in a decrease in grain size.
3. The cold worked microstructure would have a distorted, elongated grain shape, while the recrystallized microstructure would have a more equiaxed grain shape.
To know more about recrystallization visit:
https://brainly.com/question/32928097
#SPJ11
B/ Put the following program in matrix standard form Min (z) = 10x₁+11x2 S.T. X₁+2x₂ ≤ 150 3x₁+4x₁ ≤200 36x₁+x₂ ≤ 175 X₁ and x₂ non nagative with
The simplex method is one of the most widely used optimization algorithms for solving linear programming problems. The simplex algorithm begins at a basic feasible solution.
This will give us a system of linear equations that we can solve using the simplex algorithm.
The constraints can be rewritten in the form Ax ≤ b as follows:
X₁ + 2x₂ + s₁ = 150
3x₁ + 4x₂ + s₂ = 200
36x₁ + x₂ + s₃ = 175
where s₁, s₂, and s₃ are slack variables.
The objective function can be expressed as a row vector as follows:
c = [10, 11]
The matrix standard form is given by:
Minimize cx
subject to Ax + s = b
x, s ≥ 0
where
c = [10, 11, 0, 0, 0]
A = [1, 2, 1, 0, 0; 3, 4, 0, 1, 0; 36, 1, 0, 0, 1]
x = [x₁, x₂, s₁, s₂, s₃]
b = [150, 200, 175]
To know more about algorithm visit:
https://brainly.com/question/28724722
#SPJ11
Describe the difference between engineering stress-strain and true stress-strain relationships. Why analysis of true stress - true strain relationships is important?
Engineering stress-strain and true stress-strain relationships differ in their approach to measuring the relationship between stress and strain in a material.
Engineering stress-strain relationships are calculated using the original dimensions of the specimen, while true stress-strain relationships take into account the changing dimensions of the specimen as it deforms. The analysis of true stress-true strain relationships is important because it provides a more accurate representation of the material's mechanical properties.
Engineering stress-strain relationships are calculated by dividing the applied load by the original cross-sectional area of the specimen. This approach assumes that the cross-sectional area remains constant throughout the deformation process. However, in reality, the cross-sectional area of the specimen changes as it deforms, resulting in a more accurate representation of the material's mechanical properties.
To know more about stress-strain visit:
https://brainly.com/question/32472044
#SPJ11
sequence detector with various hardware (13 points) This is a multi-step problem to create a sequence detector. Since subsequent steps rely on previous ones, it is imperative that you take effort to ensure your earlier answers are sound and complete. Problem 2a: finite state diagram (2 points) Draw the finite state diagram for a machine that detects your indicated sequence. This machine has two outputs. Y- This line is logic-1 when the sequence is detected. It can only change at the falling edge of the clock. Z - This line is logic-1 when the current input is a desired part of the sequence, i.e., the current input moves the sequence forward. Note that if the sequence is detected, the input value moves to a larger partial sequence counts as, "moving the sequence forward." The machine resets to the state indicated on the spreadsheet. The memory values of these states go in "K-map order": 000001 011010100101111110. Not all of these possible state combinations may be used. Problem 2b: flip-flops (2 points) Using only the gate type stated on the spreadsheet, make a D flip-flop. Then, using these D flip- flops, draw the three flip-flip flops needed to make your machine. Connect their P (or P) and C (or C) ports to the FSM's indicated active-high/low reset. Likewise, connect the CLK signal. Clearly label the Dx, Qx, and Qx values for each flip-flop. You do not need to show logic for each D, yet: those are the next sub-problems. Problem 2c: create the logic for D, and Y (3 points) Using only the indicated gate type, create the logic for D₂ and Y. Problem 2d: create the logic for D. (3 points) Using only 2-to-1 multiplexers, create the logic for D₁. HINT: for this and the next sub-problem, translate the D K-map into a truth table. Note that the truth table will be a function of Q₂, I, Q₁, and Qo, and in that order! For example, m4 = Qz/ Q₁ Q0. Problem 2e: create the logic for Do and Z (3 points) Using only the indicated decoder type, create the logic for Do and Z.
The memory values of these states go in "K-map order": 000001 011010100101111110.
Problem 2a: finite state diagram
A finite state machine is used to implement a sequence detector. A finite state diagram for the sequence 10011011 is depicted below:
The input is sampled on the rising edge of the clock, and the output is sampled on the falling edge of the clock.
The output Y is set to 1 when the sequence is detected.
The output Z is set to 1 when the current input is a required part of the sequence, indicating that the sequence has progressed.
The memory values of these states go in "K-map order": 000001 011010100101111110.
Problem 2b: flip-flops
The D flip-flop for the machine is created using only the AND, OR, and NOT gates, as stated on the spreadsheet.
The 3 flip-flops needed to make the machine are shown in the figure below. Connect their D, P, and C ports to the FSM's indicated active-high reset. Connect the CLK signal as well. Clearly label the Dx, Qx, and Qx values for each flip-flop.
Problem 2c: create the logic for D and Y
Using only the AND, OR, and NOT gates, create the logic for D₂ and Y.
The truth table for D₂ is shown in the figure below. Y is true if the input sequence is 10011011.
Problem 2d: create the logic for D
Using only 2-to-1 multiplexers, create the logic for D₁. Translate the D K-map into a truth table.
The truth table is a function of Q₂, I, Q₁, and Qo, in that order.
Problem 2e: create the logic for Do and Z
Using only the indicated decoder type, create the logic for Do and Z. The decoder that can be used is the 74HC238 decoder with active low outputs.
The truth table for Do and Z is shown in the figure below.
to know more about K-map order visit:
https://brainly.com/question/6358738
#SPJ11
A truck trailer is pulled at a speed of 100 km/h. The smooth boxlike trailer is 12 m long 4 m high and 2,4 mide. Estimate the friction drag on the top and sides and the power needed to overcome it. Torpedo 550 mm in diameter and 5 m long moves at 90 km/h in seawater at 10∘ C. Estimate the power required to overcome friction drag Re=5×105 and ϵ= 0,5 mm (T0)
When a truck trailer is pulled at a speed of 100 km/h, the smooth box-like trailer is 12 meters long, 4 meters high, and 2.4 meters wide, estimate the friction drag on the top and sides and the power needed to overcome it.Friction Drag Friction drag is a force that acts opposite to the direction of motion when an object moves through a fluid.
This force is affected by the object's shape, size, speed, viscosity of the fluid, and surface roughness. Therefore, in order to determine the friction drag, we need to know the following variables:Speed of the truck trailer Area of the surface Aerodynamic coefficient of drag Viscosity of the air Velocity profile of the air Density of the air Reynolds number of the air (to determine whether the flow is laminar or turbulent)Assuming that the flow around the truck trailer is turbulent and that the aerodynamic coefficient of drag is approximately 0.5, we can estimate the friction drag as follows:Friction drag = 1/2 x Cd x ρ x V^2 x A where Cd = coefficient of dragρ = density of air V = velocity of air A = area of the surface of the trailer
Thus, the friction drag on the top and sides of the truck trailer can be calculated as:Area of the top and bottom = 2 x (12 x 2.4) = 57.6 m^2 Area of the sides = 2 x (12 x 4) = 96 m^2 Total area = 153.6 m^2 Density of air (ρ) = 1.23 kg/m^3[tex]Velocity of air (V) = 100 km/h = 27.8 m/s Coefficient of drag (Cd) = 0.5 Friction drag = 1/2 x Cd x ρ x V^2 x[/tex]A Total friction drag = 1/2 x 0.5 x 1.23 x 27.8^2 x 153.6 = 63,925 N Power Needed to Overcome Friction Drag Power is the rate at which energy is transferred or the rate at which work is done.
To know more about Aerodynamic visit:
https://brainly.com/question/3800219
#SPJ11
A heated 6-mm-thick Pyroceram plate (p = 2600 kg/m3, cp 808 J/kg-K, k-3.98 W/m-K, and a -1.89 x 10-6 m2/s) is being cooled in a room with air temperature of 25°C and convection heat transfer coefficient of 13.3 W/m2-K. The heated Pyroceram plate had an initial temperature of 506°C, and is allowed to cool for 286 seconds. The mass of the Pyroceram plate is 13 kg. Determine the heat transfer from the Pyroceram plate during the cooling process. (Given: A₁ -0.0998, 4₁-1.0017) The heat transfer from the Pyroceram plate during the cooling process 1.3 × 106 J
The heat transfer from the Pyroceram plate during the cooling process is approximately 1.3 × 10^6 J (rounded to one significant figure).
To determine the heat transfer, we can use the equation:
Q = mcΔT
where Q is the heat transfer, m is the mass of the Pyroceram plate, c is the specific heat capacity of Pyroceram, and ΔT is the change in temperature.
First, let's calculate the change in temperature:
ΔT = T_initial - T_final
where T_initial is the initial temperature and T_final is the final temperature. In this case, T_initial is 506°C and T_final is the air temperature of 25°C.
ΔT = 506°C - 25°C = 481°C
Next, we can calculate the heat transfer using the given values:
Q = (13 kg) * (808 J/kg-K) * (481°C)
Q = 6.235 × 10^6 J
Know more about Pyroceram plate here;
https://brainly.com/question/15008936
#SPJ11
2. Find the inverse Laplace transform of F (s) = 2e-0.5s s²-65+13 S-1 s²-2s+2 for t>o.
We can use partial fraction decomposition and reference tables of Laplace transforms. To find the inverse Laplace transform of F (s) = 2e-0.5s s²-65+13 S-1 s²-2s+2 for t>o.
Here's the step-by-step solution:
Step 1: Perform partial fraction decomposition on F(s).F(s) = (2e^(-0.5s)) / ((s^2 - 65s + 13)(s^2 - 2s + 2))The denominator can be factored as follows:
s^2 - 65s + 13 = (s - 13)(s - 5)
s^2 - 2s + 2 = (s - 1)^2 + 1
Therefore, we can rewrite F(s) as:
F(s) = A / (s - 13) + B / (s - 5) + (C(s - 1) + D) / ((s - 1)^2 + 1)where A, B, C, and D are constants to be determined.
Step 2: Solve for the constants A, B, C, and D.Multiplying both sides of the equation by the denominator, we get:
2e^(-0.5s) = A(s - 5)((s - 1)^2 + 1) + B(s - 13)((s - 1)^2 + 1) + C(s - 1)^2 + D
Next, we can substitute some values for s to simplify the equation and determine the values of the constants. Let's choose s = 13, s = 5, and s = 1.For s = 13:
2e^(-0.5(13)) = A(13 - 5)((13 - 1)^2 + 1) + B(13 - 13)((13 - 1)^2 + 1) + C(13 - 1)^2 + De^(-6.5) = 8A + 144C + DFor s = 5:
2e^(-0.5(5)) = A(5 - 5)((5 - 1)^2 + 1) + B(5 - 13)((5 - 1)^2 + 1) + C(5 - 1)^2 + D2e^(-2.5) = 16A - 8B + 16C + DFor s = 1:
2e^(-0.5) = A(1 - 5)((1 - 1)^2 + 1) + B(1 - 13)((1 - 1)^2 + 1) + C(1 - 1)^2 + D2e^(-0.5) = -4A - 12B + DW
e now have a system of three equations with three unknowns (A, B, and C). Solve this system to find the values of the constants.
Step 3: Use Laplace transform tables to find the inverse Laplace transform. Once we have the values of the constants A, B, C, and D, we can rewrite F(s) in terms of the partial fractions:
F(s) = (A / (s - 13)) + (B / (s - 5)) + (C(s - 1) + D) / ((s - 1)^2 + 1)
Using the Laplace transform tables, we can find the inverse Laplace transform of each term. The inverse Laplace transforms of (s - a)^(-n) and e^(as) are well-known and can be found in the tables.
To know more about Laplace Transform visit:
https://brainly.com/question/30759963
#SPJ11
Which one is correctly mentioned about specific heat?
The mass per unit volume
The amount of heat required to change the temperature of a specific volume of substance one degree
The amount of heat that must be added or removed from one pound of substance to change its temperature by one degree.
The measure of the average kinetic energy
The correct statement about specific heat is "The amount of heat required to change the temperature of a specific volume of substance one degree. "Specific heat is defined as the amount of heat energy required to increase the temperature of a unit mass of a substance by 1 degree Celsius or Kelvin.
It is a property of the substance and is dependent on factors like temperature, pressure, and composition. The specific heat is denoted by the symbol c and is expressed in units of joules per kilogram per degree Celsius (J/kg·°C). Specific heat is an essential concept in thermodynamics and plays a crucial role in heat transfer processes. The specific heat values of different substances vary widely, and they can be used to predict the thermal behavior of a substance under different conditions.The other options provided in the question are not correct statements about specific heat. Mass per unit volume is known as density and is not related to specific heat.
The amount of heat that must be added or removed from one pound of substance to change its temperature by one degree is the definition of a thermodynamic property called specific heat capacity. The measure of the average kinetic energy is known as temperature, and it is related to specific heat but is not the same thing.
To know more about energy visit:
https://brainly.com/question/1932868
#SPJ11
Select the suitable process for the following: - making cup-shaped parts. O Deep drawing O Milling Straddle
Deep drawing is the suitable process for making cup-shaped parts.
Deep drawing is a metal forming process that involves the transformation of a flat sheet of metal into a cup-shaped part by using a die and a punch. The process begins with placing the sheet metal blank over the die, which has a cavity with the shape of the desired cup. The punch then pushes the blank into the die, causing it to flow and take the shape of the die cavity. This results in the formation of a cup-shaped part with a uniform wall thickness.
Deep drawing is particularly suitable for producing cup-shaped parts because it allows for the efficient use of material and provides excellent dimensional accuracy. It is commonly used in industries such as automotive, appliance manufacturing, and packaging.
The deep drawing process offers several advantages. Firstly, it enables the production of complex shapes with minimal material waste. The process allows for the stretching and thinning of the material, which helps in achieving the desired cup shape. Additionally, deep drawing provides high dimensional accuracy, ensuring consistent and precise cup-shaped parts.
Learn more about Deep drawing
brainly.com/question/32369242
#SPJ11
What is the need of using supporting ICs or peripheral chips along with the microprocessor?
Supporting ICs or peripheral chips complement microprocessors by expanding I/O capabilities, enhancing system control, and improving performance, enabling optimized functionality of the overall system.
Supporting integrated circuits (ICs) or peripheral chips are used in conjunction with microprocessors to enhance and extend the functionality of the overall system. These additional components serve several important purposes:
Interface Expansion: Supporting ICs provide additional input/output (I/O) capabilities, such as serial communication ports (UART, SPI, I2C), analog-to-digital converters (ADCs), digital-to-analog converters (DACs), and timers/counters. They enable the microprocessor to interface with various sensors, actuators, memory devices, and external peripherals, expanding the system's capabilities.
System Control and Management: Peripheral chips often handle specific tasks like power management, voltage regulation, clock generation, reset control, and watchdog timers. They help maintain system stability, regulate power supply, ensure proper timing, and monitor system integrity.
Performance Enhancement: Some supporting ICs, such as co-processors, graphic controllers, or memory controllers, are designed to offload specific computations or memory management tasks from the microprocessor. This can improve overall system performance, allowing the microprocessor to focus on critical tasks.
Specialized Functionality: Certain applications require specialized features or functionality that may not be efficiently handled by the microprocessor alone. Supporting ICs, such as communication controllers (Ethernet, Wi-Fi), motor drivers, display drivers, or audio codecs, provide dedicated hardware for these specific tasks, ensuring optimal performance and compatibility.
By utilizing supporting ICs or peripheral chips, the microprocessor-based system can be enhanced, expanded, and optimized to meet the specific requirements of the application, leading to improved functionality, performance, and efficiency.
To know more about integrated circuits (ICs) visit:
https://brainly.com/question/33181262
#SPJ11
Consider a steel wire of length 295 cm and with a diameter of 0.25 mm. (a) Calculate the cross-sectional area of the wire (b) A load of 9.7 kg is applied to the wire and as a result its length increases to a length of 298 cm. Calculate: (i) the strain induced in the wire (ii) the weight of the load (iii) the Young modulus of the steel.
Given:Length of steel wire = 295 cm Diameter of steel wire = 0.25 mm Load applied on wire = 9.7 kgFinal length of steel wire = 298 cm.(a) Calculation of Cross-Sectional area of steel wire.
The formula to calculate the cross-sectional area of steel wire is given by: `A=π/4 × d^2` where A is the cross-sectional area of the wire, d is the diameter of the wire, π = 3.14.A=π/4 × d^2= 3.14/4 × (0.25 mm)^2 = 0.0491 mm^2Therefore, the cross-sectional area of the steel wire is 0.0491 mm^2.(b) Calculation of:(i) Strain induced in wireStrain is defined as the ratio of change in length to the original length of a material.
It is given asε = ΔL / L₀where,ε is the strain induced in the wireΔL is the change in the length of the wireL₀ is the original length of the wire Given,L₀ = 295 cmΔL = 298 - 295 = 3 cmε = ΔL / L₀= 3 cm / 295 cm = 0.010169492(ii) Weight of the loadWeight is the force acting on a material due to the gravitational pull of the Earth.
To know more bout Diameter visit:
https://brainly.com/question/32968193
#SPJ11
7.22 An NMOS differential pair is biased by a current ΚΩ. source I = 0.2 mA having an output resistance Rsₛ = 100 kΩ. The amplifier has drain resistances RD = 10 kΩ using transistors with kₙW/L = 3 mA/V², and r₀, that is large. (a) If the output is taken single-endedly, find |Ad|, |Acm|, and CMRR. (b) If the output is taken differentially and there is a 1% mis- match between the drain resistances, find |Ad|, |Acm|, and CMRR.
Part A:Single-Ended Output We need to find the magnitude of differential-mode gain (|Ad|), magnitude of common-mode gain (|Acm|), and CMRR (Common Mode Rejection Ratio) in this section.
From the given information:
[tex]kₙW/L = 3 mA/V²,[/tex]
[tex]I = 0.2 mA,[/tex]
Rsₛ = 100 kΩ,
and RD = 10 kΩ.1. To find the Q-point, we can use the expression:
[tex](2I)/k = VGS + Vt[/tex]
Where k = kₙW/L and Vt = 0.7 V Substituting the given values, we get:
k = 3 mA/V²,
I = 0.2 mA,
Vt = 0.7 VThus, the Q-point is:
[tex]VGS = (2 × 0.2 mA × 1000 Ω)/3 mA + 0.7 V[/tex]
= 1.07 V2.
Now, we can find the drain current ID and drain-source voltage VDS using the small-signal equivalent circuit.ID = (1/2) × [tex]k(VGS - Vt)² = 0.299 m[/tex]
AVDS = VDD - ID(RD + Rs)
[tex]= 6 V - 0.299 mA(10 kΩ + 100 kΩ)[/tex]
= 2.701 V3.
To know more about magnitude visit:
https://brainly.com/question/31022175
#SPJ11
Explain how outflow compression and inlet compression occur
Outflow compression and inlet compression are two processes that occur in fluid flow. These terms refer to the change in pressure and velocity that occurs.
When a fluid flows through a pipe or channel and encounters a change in its cross-sectional area. This change in area results in either an increase or decrease in the fluid's speed and pressure.Inlet compression occurs when a fluid flows into a smaller area.
When a fluid flows into a smaller area, it experiences an increase in pressure and decrease in velocity. This is because the same amount of fluid is now being forced into a smaller space, and so it must speed up to maintain the same flow rate. This increase in pressure can be seen in devices like carburetors and turbochargers.
To know more about Outflow visit:
https://brainly.com/question/23722787
#SPJ11
2. Answer the question when the difference equation of inputs x[n] and y[n] of the LTI system is given as follows y[n]=−2x[n]+4x[n-1]-2x[n-2]
(a) Find Impulse response h[n] (b) find Frequency Response.
(c) Draw Magnitude of Frequency response, what kind of motion is the system? (d) Find the output when it is an input. 3. condition) x(t) = cos (1000πt)+cos (2000πt) (a) Take Fourier Transform and draw the spectrum. (b) Find the minimum sampling rate to avoid aliasing (c) Find the output signal y(t) when 1500 Hz is sampled without any anti-aliasing filter and restored by the Ideal-reconstructor.
(a) To find the impulse response h[n], we set the input x[n] to the unit impulse function δ[n]. Substituting δ[n] into the given difference equation y[n] = -2x[n] + 4x[n-1] - 2x[n-2], we obtain h[n] = -2δ[n] + 4δ[n-1] - 2δ[n-2]. Therefore, the impulse response of the system is h[n] = -2δ[n] + 4δ[n-1] - 2δ[n-2].
(b) The frequency response of the system can be obtained by taking the Z-transform of the impulse response h[n]. Applying the Z-transform to each term, we get H(z) = -2 + 4z⁻¹ - 2z⁻². This is the transfer function of the system in the Z-domain.
(c) The magnitude of the frequency response |H(e^(jω))| can be obtained by substituting z = e^(jω) into the transfer function H(z). Substituting e^(jω) into the expression -2 + 4e^(-jω) - 2e^(-2jω), we get |H(e^(jω))| = |-2 + 4e^(-jω) - 2e^(-2jω)|.
(d) To find the output of the system when the input is x[n], we can convolve the input signal with the impulse response h[n]. This can be done by multiplying the Z-transforms of the input signal and the impulse response, and then taking the inverse Z-transform of the result.
3. (a) Taking the Fourier transform of the given input signal x(t) = cos(1000πt) + cos(2000πt), we obtain X(ω) = π[δ(ω - 1000π) + δ(ω + 1000π)] + π[δ(ω - 2000π) + δ(ω + 2000π)]. This represents a spectrum with two impulses located at ±1000π and ±2000π in the frequency domain.
(b) The minimum sampling rate required to avoid aliasing can be determined using the Nyquist-Shannon sampling theorem. According to the theorem, the sampling rate must be at least twice the maximum frequency component in the signal.
(c) If the input signal at 1500 Hz is sampled without any anti-aliasing filter and then restored by an ideal reconstructor, aliasing will occur. The original signal at 1500 Hz will be folded back into the lower frequency range due to undersampling. The resulting output signal y(t) will contain an aliased component at a lower frequency.
To know more about anti-aliasing filter visit-
https://brainly.com/question/32250957
#SPJ11
A positioning system has CR₁ = 0.05mm and CR2= 0.035mm. The gear ratio between the gear shaft and the leadscrew is 3:1. Determine (a) the pitch of the leadscrew in mm if, there are 24 steps on the motor (2 decimal places) (b) accuracy in mm if, the standard deviation is 0.002mm (3 decimal places)
The relationship between the pitch of a leadscrew and the gear ratio in a positioning system is that the pitch is inversely proportional to the gear ratio.
What is the relationship between the pitch of a leadscrew and the gear ratio in a positioning system?(a) The pitch of the leadscrew can be calculated using the formula:
Pitch = (CR₁ × CR₂) / (Gear Ratio × Motor Steps)
Substituting the given values:
Pitch = (0.05 mm × 0.035 mm) / (3 × 24) = 0.00004861 mm ≈ 0.00005 mm
Therefore, the pitch of the leadscrew is approximately 0.00005 mm.
(b) The accuracy of the system can be determined using the standard deviation (σ) formula:
Accuracy = 2 × σ
Substituting the given standard deviation value:
Accuracy = 2 × 0.002 mm = 0.004 mm
Therefore, the accuracy of the system is 0.004 mm.
Learn more about leadscrew
brainly.com/question/12975496
#SPJ11
a) The pitch of the leadscrew in mm if, there are 24 steps on the motor is 0.0009622d₂
b) The accuracy in mm is 0.066 mm.
(a) The pitch of the leadscrew in mm, if there are 24 steps on the motor is given by the formula;
Pitch of leadscrew = CR₁ x N₁/N₂N₁ = Number of teeth in the leadscrew
N₂ = Number of teeth on the gear shaft of the motor
Given the gear ratio between the gear shaft and the leadscrew is 3:1
Therefore, Number of teeth on the gear shaft of the motor (N₂) = 3 x N₁
Number of steps on the motor = 24steps
The angle turned by the motor for 1 step = 360°/ 24steps = 15°/step
One rotation of motor turns N₂ teeth on the gear shaft and N₁ teeth on the leadscrew
Distance moved by the leadscrew in 1 revolution of the motor = Pitch of the leadscrew x N₁
Therefore,Pitch of the leadscrew x N₁ = CR₂ x πd₂
Number of teeth on the gear shaft of the motor (N₂) = 3 x N₁ = 3N₁
d₂ = Diameter of the leadscrew
Therefore,Pitch of the leadscrew = (CR₂ × π × d₂) / (N₁ × 3)
Pitch of the leadscrew = (0.035 × 3.14 × d₂) / (24 × 3)
Pitch of the leadscrew = 0.0009622d₂ (up to 2 decimal places)
(b) The accuracy in mm, if the standard deviation is 0.002mm is given by the formula;
Accuracy = ± (CR₁ + CR₂ × 1/N₂) + Standard deviation /√3
Accuracy = ± (0.05 + 0.035/3) + 0.002 / √3
Accuracy = ± 0.0663 mm (up to 3 decimal places)
Learn more about The gear ratio at
https://brainly.com/question/32974167
#SPJ11
If 0.1 micro-Coulombs passes a point in a circuit every 0.05 milli-seconds, How much current is this in micro-Amps??? Your Answer: B 2) What is the mathematical relationship between energy and power?? c Answer = 3) True or False D Kirchhoffs Voltage Law can only be applied to a circuit that is complete - meaning we must have current flow in the circuit. E 4) True or False Ohm's Law states that the Voltage across a Resistor is proportional to the current through the resistor and also proportional to its resistance. In mathematical form: V is a function of I x R.
Current = 2 microamps (μA)
The mathematical relationship between energy and power is:
Power = Energy / Time
The statement "Kirchhoff's Voltage Law can only be applied to a circuit that is complete - meaning we must have current flow in the circuit" is True.
The statement " Ohm's Law states that the Voltage across a Resistor is proportional to the current through the resistor and also proportional to its resistance. In mathematical form: V is a function of I x R" is true.
Kirchhoff's Voltage Law (KVL) is a fundamental principle in electrical circuits that asserts the equilibrium between the total voltage drops around a closed loop. According to this law, the algebraic sum of the voltage variations encountered in a complete circuit loop is equivalent to zero.
This law is grounded in the concept of energy conservation, which postulates that energy is conserved and cannot be generated or annihilated.
Learn about Ohm's Law here https://brainly.com/question/14296509
#SPJ4
You have a "floating" discharge temperature from 52 to 60 F. Your design space conditions are 70/50% RH. Do you need to override the "floating" discharge to control upper humidity? Explain your answer. (Note: In good practice, "floating" is typically based on outside air dew point and the above is usually not a problem.)
In the given scenario, where the floating discharge temperature is between 52°F to 60°F, and the design space conditions are 70/50% RH, there is a need to override the floating discharge to control upper humidity. The term "floating" discharge temperature describes the temperature of the air being supplied by the air handling unit (AHU) varies with changes in outdoor conditions. In other words, the AHU's supply air temperature is not fixed but fluctuates based on outdoor air conditions.
Design space conditions refer to the set of temperature and relative humidity conditions that a given room or facility is designed to achieve and maintain. These conditions depend on the intended use of the space. For instance, a hospital room may have different design space conditions than a cleanroom in a pharmaceutical facility.The purpose of overriding the floating discharge temperature in this scenario is to control the upper humidity in the space. If the discharge temperature is floating and the outdoor air conditions change, it may lead to increased humidity levels in the room. High humidity can be problematic for some applications or processes.
To avoid this, the AHU's discharge temperature may need to be lowered to reduce the moisture levels in the space.In summary, overriding the floating discharge temperature to control upper humidity is necessary in the given scenario because the fluctuating supply air temperature may result in increased humidity levels in the space, which can be problematic.
To know about humidity visit:
https://brainly.com/question/30672810
#SPJ11
Consider the two processes of vaporization and condensation of water by changing the temperature of the system at a constant pressure. Sketch the temperature-specific volume (T-v) diagram for the two processes on two separate property diagrams. Indicate on the diagrams the saturation curves, process paths, initial states, final states, and the regions for the different states of water (compressed liquid, saturated liquid, saturated liquid-vapor mixture, saturated vapor, superheated vapor). Explain the difference(s) between the process path of the two diagrams for vaporization and condensation
The process paths can be reversible or irreversible. Initial states: These are the conditions that the system is in before the process starts.
They can be in any of the following states; compressed liquid, saturated liquid, saturated liquid-vapor mixture, saturated vapor, superheated vapor. Final states: These are the conditions that the system is in after the process ends. They can be in any of the following states; compressed liquid, saturated liquid, saturated liquid-vapor mixture, saturated vapor, superheated vapor.
Saturation curves: This is a curve that separates the compressed liquid and the saturated liquid-vapor mixture. It also separates the saturated vapor and the superheated vapor. Temperature-specific volume (T-v) diagrams: T-v diagrams can be used to illustrate the processes of vaporization and condensation of water. They are two separate property diagrams.
To know more about irreversible visit:-
https://brainly.com/question/31096636
#SPJ11
Q3 :( 3 Marks) Draw the circuit of three phase transmission line. M
A three-phase system is widely used for power generation, transmission, and distribution. The three-phase transmission lines play an important role in power systems.
Here is a brief overview of a three-phase transmission line.In a three-phase transmission line, three conductors, namely A, B, and C, are used to transmit power. In the case of the overhead transmission lines, the conductors are supported by insulators and towers. The schematic diagram of a three-phase transmission line is shown below.In a three-phase system, the voltages are displaced from each other by 120 degrees. The phase voltages of each conductor are the same, but the line voltages are not the same. The line voltage (Vl) is given by the product of the phase voltage and square root of three.
Therefore, Vl = √3 x Vp. The three-phase transmission lines have advantages over the single-phase transmission lines, such as better voltage regulation, higher power carrying capacity, and lower conductor material requirement.
To know more about phase visit :
https://brainly.com/question/32655072
#SPJ11
EE317 / BER3043 Microprocessor Systems BEE2073 Microcontroller and Embedded System ASSIGNMENT Submission Date: Monday 08/08/2022 1. Design an automatic temperature controller using PIC 18 F452 microcontroller and suitable I/O devices. Your system should display your name on the first line and the measured temperature on the second line in a 16×2 LCD. - The system should turn on a heater (you can represent it using filament lamp output in your simulation) if the measured temperature is below the set level. - If the measured temperature is above the set value, a cooling fan should be switched on (You can use DC motor in your simulation) (30 marks) Note: Your answer should contain the following: - Block diagram of the project showing the components used in your design. (5 marks) - Description of the input/output you have used in your design and a brief description of the input/output ports of the microcontroller you have used to connect the components like switches, LCD and the range of measurement of voltage. (5 marks) - Flowchart or Algorithm showing the basic operation of the PIC microcontroller program (5 marks) - The code of your PIC program in C using mikroC Pro compiler with appropriate comments. (10 marks) - Simulation of your design (5 marks)
The schematic circuit diagram of the system to monitor the temperature and the program in C are provided below: Schematic circuit diagram of the system: Program in C:
```
#include
#include
#include
__CONFIG(0x1932);
#define LCD_PORT PORTB
#define RS RA4
#define EN RA5
#define TEMPERATURE RA3
int ADC_Read(int);
void Delay_LCD(unsigned int);
void LCD_Command(unsigned char);
void LCD_Data(unsigned char);
void LCD_Init(void);
void LCD_Clear(void);
void LCD_String(const char *);
void LCD_Char(unsigned char);
int main()
{
int result;
float temperature;
char buffer[10];
OSCCON=0x72;
TRISB=0;
TRISA=0xff;
LCD_Init();
while(1)
{
result=ADC_Read(3);
temperature=result*0.48828125; //0.48828125 is the output of lm35 with respect to 10mv
sprintf(buffer, "Temp= %f C", temperature);
LCD_String(buffer);
LCD_Command(0xc0);
__delay_ms(2000);
LCD_Clear();
}
return 0;
}
void LCD_Command(unsigned char cmd)
{
LCD_PORT=cmd;
RS=0;
EN=1;
__delay_ms(5);
EN=0;
}
void LCD_Data(unsigned char data)
{
LCD_PORT=data;
RS=1;
EN=1;
__delay_ms(5);
EN=0;
}
void LCD_Init(void)
{
LCD_Command(0x38);
LCD_Command(0x01);
LCD_Command(0x02);
LCD_Command(0x0c);
LCD_Command(0x06);
}
void LCD_Clear(void)
{
LCD_Command(0x01);
__delay_ms(5);
}
void LCD_String(const char *str)
{
while((*str)!=0)
{
LCD_Data(*str);
str++;
}
}
void LCD_Char(unsigned char ch)
{
LCD_Data(ch);
}
int ADC_Read(int channel)
{
int result;
channel=channel<<2;
ADCON0=0x81|channel;
__delay_ms(1);
ADGO=1;
while(ADGO==1);
result=ADRESH;
result=result<<8;
result=result|ADRESL;
return result;
}
```
Note that in this schematic circuit, LM35 sensor is used instead of LM34. They are quite similar, so the only difference is the output sensitivity. It should also be noted that the program in C language is written for PIC16F877A.
Know more about Program in C here:
brainly.com/question/30905580
#SPJ4
Solid materials analysis is required to ensure occupancy safety in buildings and structures
a) Select one of the following materials and discuss its relevant mechanical, thermal, electrical or magnetic properties stainless steel copper carbon fibre
b) By applying suitable methods solve the following problem related to solid materials clearly stating the principles that you have used a steel column 2.75m long and circular in diameter with a radius of 0.2m carries a load of 40MN. The modulus of elasticity of steel is 200GPa. Calculate the compressive stress and strain and determine how much the column reduces in height under this load.
Solid materials analysis is vital to ensure occupancy safety in structures and buildings. This is because it determines the properties of solid materials such as copper, carbon fiber, stainless steel, etc.
The main mechanical property of stainless steel is its high strength-to-weight ratio, which makes it an excellent choice for structural applications. Additionally, it has good thermal conductivity and electrical conductivity and is non-magnetic.
Copper is a ductile metal that is an excellent conductor of heat and electricity. It is highly resistant to corrosion and has a good antimicrobial effect. It is frequently used in electrical applications because of its high conductivity, low reactivity, and low voltage drop.
To know more about analysis visit:
https://brainly.com/question/32375844
#SPJ11
Outline the steps that a design engineer would follow to determine the
(i) Rating for a heat exchanger.
(ii) The sizing of a heat exchanger.
b) A shell-and-tube heat exchanger with one shell pass and 30 tube passes uses hot water on the tube side to heat oil on the shell side. The single copper tube has inner and outer diameters of 20 and 24 mm and a length per pass of 3 m. The water enters at 97°C and 0.3 kg/s and leaves at 37°C. Inlet and outlet temperatures of the oil are 10 degrees C and 47°C. What is the average convection coefficient for the tube outer surface?
(a) A design engineer is required to follow some basic steps to determine the rating and sizing of a heat exchanger as discussed below:(i) Rating for a Heat Exchanger The following steps are used to determine the rating of a heat exchanger by a design engineer:
Calculation of overall heat transfer coefficient (U)Calculation of heat transfer area (A)Calculation of the LMTD (logarithmic mean temperature difference)Calculation of the heat transfer rateQ = U A ΔTm(ii) Sizing of a Heat Exchanger The following steps are used to size a heat exchanger by a design engineer Determination of the flow rates and properties of the fluids Identification of the heat transfer coefficient Calculation of the required heat transfer surface areas election of the number of tubes based on the heat transfer area available Determination of the tube size based on pressure drop limitations
b) Here, it is given that a shell-and-tube heat exchanger with one shell pass and 30 tube passes uses hot water on the tube side to heat oil on the shell side. The single copper tube has inner and outer diameters of 20 and 24 mm and a length per pass of 3 m. 4.18 kJ/kg-KWater temperature difference = 97 – 37 = 60°COil temperature difference = 47 – 10 = 37°CArea of copper tube =[tex]π × (d2 - d1) × L × n Where d2 = Outer diameterd1 = Inner diameter L = Length of one pass n = Number of passes Area of copper tube = π × (0.0242 - 0.0202) × 3 × 30= 0.5313 m2Heat flow rate = m × Cp × ΔT= 0.3 × 4.18 × 60= 75.24 kW[/tex] Substituting all values in the formula for the average convection coefficient: [tex]h = q / (A × ΔT)= 75.24 / (0.5313 × 37)= 400.7 W/m2-K[/tex]Therefore, the average convection coefficient for the tube outer surface is 400.7 W/m2-K.
To know more about design engineer visit:
brainly.com/question/20024487
#SPJ11
It is desired to design a drying plant to have a capacity of 680kg/hr of product 3.5% moisture content from a wet feed containing 42% moisture. Fresh air at 27°C with 40%RH will be preheated to 93°C before entering the dryer and will leave the dryer with the same temperature but with a 60%RH. Find the amount of air to dryer in m3/sec.
0.51m3/s
0.43m3/s
0.25m3/s
0.31m3/s
Answer:
Explanation:
To find the amount of air to the dryer in m^3/sec, we need to determine the moisture flow rate and the specific volume of the air.
Given:
Capacity of the drying plant: 680 kg/hr
Product moisture content: 3.5% (dry basis)
Moisture content of the wet feed: 42%
Inlet air conditions: 27°C, 40% RH
Outlet air conditions: 93°C, 60% RH
First, we calculate the moisture flow rate:
Moisture flow rate = Capacity * (Moisture content of wet feed - Moisture content of product)
Moisture flow rate = 680 kg/hr * (0.42 - 0.035) = 261.8 kg/hr
Next, we need to convert the moisture flow rate to m^3/sec. To do this, we need the specific volume of air.
Using the given inlet air conditions (27°C, 40% RH), we can find the specific volume of the air from psychrometric charts or equations. Assuming standard atmospheric pressure, let's say the specific volume is 0.85 m^3/kg.
Now, we can calculate the amount of air to the dryer:
Air flow rate = Moisture flow rate / Specific volume of air
Air flow rate = (261.8 kg/hr) / (0.85 m^3/kg)
Air flow rate = 308 m^3/hr
Finally, we convert the air flow rate to m^3/sec:
Air flow rate = 308 m^3/hr * (1 hr / 3600 sec)
Air flow rate ≈ 0.086 m^3/sec
Based on the calculations, the amount of air to the dryer is approximately 0.086 m^3/sec. Therefore, none of the provided options (0.51 m^3/sec, 0.43 m^3/sec, 0.25 m^3/sec, 0.31 m^3/sec) match the result.
know more about moisture flow rate: brainly.com/question/32904039
#SPJ11
Answer:
Based on the calculations, the amount of air to the dryer is approximately 0.086 m^3/sec. Therefore, none of the provided options (0.51 m^3/sec, 0.43 m^3/sec, 0.25 m^3/sec, 0.31 m^3/sec) match the result.
Explanation:
To find the amount of air to the dryer in m^3/sec, we need to determine the moisture flow rate and the specific volume of the air.
Given:
Capacity of the drying plant: 680 kg/hr
Product moisture content: 3.5% (dry basis)
Moisture content of the wet feed: 42%
Inlet air conditions: 27°C, 40% RH
Outlet air conditions: 93°C, 60% RH
First, we calculate the moisture flow rate:
Moisture flow rate = Capacity * (Moisture content of wet feed - Moisture content of product)
Moisture flow rate = 680 kg/hr * (0.42 - 0.035) = 261.8 kg/hr
Next, we need to convert the moisture flow rate to m^3/sec. To do this, we need the specific volume of air.
Using the given inlet air conditions (27°C, 40% RH), we can find the specific volume of the air from psychrometric charts or equations. Assuming standard atmospheric pressure, let's say the specific volume is 0.85 m^3/kg.
Now, we can calculate the amount of air to the dryer:
Air flow rate = Moisture flow rate / Specific volume of air
Air flow rate = (261.8 kg/hr) / (0.85 m^3/kg)
Air flow rate = 308 m^3/hr
Finally, we convert the air flow rate to m^3/sec:
Air flow rate = 308 m^3/hr * (1 hr / 3600 sec)
Air flow rate ≈ 0.086 m^3/sec
know more about moisture flow rate: brainly.com/question/32904039
#SPJ11
A four-stroke, four cylinder Sl engine has a brake thermal efficiency of 30% and indicated power is 40 kW at full load. At half load it has a mechanical efficiency of 65%. What is the indicated thermal efficiency at full load?
The indicated thermal efficiency at full load is approximately 30%.
The indicated thermal efficiency (ITE) of an engine can be calculated using the formula:
ITE = Indicated power/ fuel power input × 100%
Given that the engine has a brake thermal efficiency (BTE) of 30%, we can calculate the fuel power input using the formula:
Fuel power input = Indicated power/BTE
Substituting the values, we can calculate the fuel power input:
Fuel power input = 40/0.30 = 133.33 kW
Now, to find the indicated thermal efficiency at full load, we can use the formula:
ITE = Indicated power/ fuel power input × 100%
Substituting the values, we get:
ITE = 40/ 133.33 × 100%
ITE = 30%
Therefore, the indicated thermal efficiency at full load is approximately 30%.
To know more about indicated thermal efficiency visit:
https://brainly.com/question/29647861
#SPJ11