Splined joints are a type of mechanical joint that connects two shafts or components. Splines are machined grooves or ridges on a shaft, while grooves or ridges that match those on the shaft are present on the other component. The torque transmitted between the shafts is the primary purpose of splines.
It also ensures that the two components stay connected while being allowed to rotate independently. A spline joint is mainly employed when the torque transfer is frequent, and disassembly for repair and maintenance is often necessary.
A.) Safe torque capacity of the splined connection, sliding under load.
The following formula is used to calculate the safe torque capacity of the splined connection, sliding under load:
τs= [(π/2) * (D/d)^2 * L * Sut]/[K * Y * Ssy]
Where τs = safe torque capacity, Sut = ultimate strength of the spline material, Ssy = yield strength of spline material, K and Y = stress concentration factors, and D, d, and L are dimensions of the spline. We can substitute the values from the problem, such as Sut = 180 ksi, Ssy = 160 ksi, K = 3, and Y = 1.5.
When we substitute these values in the above formula, we get:
τs = [(π/2) * (1.31/1.122)^2 * 1 15/16 * 180]/[3 * 1.5 * 160]
τs = 508 lb-ft.
B.) Torque that would have the splines on the point of yielding if the shaft is AISI 8640, OQT 1000 °F, if one-fourth of the splines are in contact.
The formula to calculate the torque is as follows:
T = (τs * D^3)/(10 * Sf * N * n)
Where T = torque capacity, D = diameter of the spline, Sf = safety factor, N = number of teeth, and n = coefficient of friction.
Substituting the given values, we get:
T = (508 * 1.31^3)/(10 * 1.5 * 10 * 0.25)
T = 836 lb-ft.
To know more about torque visit:
https://brainly.com/question/30338175
#SPJ11
Determine the level of service? for six lanes undivided level highway. The width of lane, shoulder on the right side, and shoulder on the left side are 10 ft, 2 ft, and 2 ft respectively. The directional hour volume is 3500 Veh/h. The traffic composition includes 15% trucks and 1% RVs. The peak hour factor is 0.80. Unfamiliar drivers use the road that has 10 access points per mile. The design speed is 55 mi/h. Discuss possible modifications to upgrade the level of service?
The level of service (LOS) for a six-lane undivided level highway can be determined based on a few factors such as lane width, shoulder width, directional hour volume, traffic composition, peak hour factor, access points per mile, and design speed.
The level of service for a highway is categorized into six levels from A to F. Level A is for excellent service, and level F is for the worst service. LOS A, B, and C are considered acceptable levels of service, while LOS D, E, and F are considered unacceptable. The following are the steps to determine the level of service for the given information:
Step 1: Calculate the flow rate (q)
The flow rate is calculated by multiplying the directional hour volume by the peak hour factor.
q = 3500 x 0.80 = 2800 veh/h
Step 2: Calculate the capacity (C)
The capacity of a six-lane undivided highway is calculated using the following formula:
C = 6 x (w/12) x r x f
Where w is the width of each lane, r is the density of traffic, and f is the adjustment factor for lane width and shoulder width.
C = 6 x (10/12) x (2800/60) x 0.89 = 1480 veh/h
Step 3: Calculate the density (k)
The density of traffic is calculated using the following formula:
k = q/v
Where v is the speed of the vehicle.
v = 55 mph = 55 x 1.47 = 80.85 ft/s
k = 2800/3600 x 80.85 = 62.65 veh/mi
Step 4: Calculate the LOS
The LOS is calculated using the Highway Capacity Manual (HCM) method.
LOS = f(k, C)
From the HCM table, it can be determined that the LOS for a six-lane undivided highway with the given information is D.
Possible modifications to upgrade the level of service:
1. Widening the shoulder on the right side and the left side from 2 ft to 4 ft. This can increase the adjustment factor (f) from 0.89 to 0.91, which can improve the capacity (C) and the LOS.
2. Reducing the number of access points per mile from 10 to 6. This can decrease the density of traffic (k), which can improve the LOS.
3. Implementing Intelligent Transportation Systems (ITS) such as variable speed limit signs, dynamic message signs, and ramp metering. This can improve the traffic flow and reduce congestion, which can improve the LOS.
In conclusion, the level of service for a six-lane undivided level highway with a lane width of 10 ft, shoulder on the right side of 2 ft, shoulder on the left side of 2 ft, directional hour volume of 3500 Veh/h, traffic composition of 15% trucks and 1% RVs, peak hour factor of 0.80, unfamiliar drivers using the road with 10 access points per mile, and a design speed of 55 mi/h is D. Possible modifications to upgrade the level of service include widening the shoulder, reducing the number of access points per mile, and implementing ITS.
To learn more about lane width visit:
brainly.com/question/1131879
#SPJ11
Stability (3 marks) Explain why the moment of stability (righting moment) is the absolute measure for the intact stability of a vessel and not GZ.
The moment of stability, also known as the righting moment, is considered the absolute measure of the intact stability of a vessel, as it provides a comprehensive understanding of the vessel's ability to resist capsizing.
The moment of stability, or righting moment, represents the rotational force that acts to restore a vessel to an upright position when it is heeled due to external factors such as wind, waves, or cargo shift. It is determined by multiplying the displacement of the vessel by the righting arm (GZ). The GZ value alone indicates the distance between the center of gravity and the center of buoyancy, providing information on the initial stability of the vessel. However, it does not consider the magnitude of the force acting on the vessel.
The moment of stability takes into account both the lever arm and the magnitude of the force acting on the vessel, providing a more accurate assessment of its stability. It considers the dynamic effects of external forces, allowing for a better understanding of the vessel's ability to return to its upright position when heeled.
Learn more about vessel stability here:
https://brainly.com/question/13485166
#SPJ11
A certain company contains three balanced three-phase loads. Each of the loads is connected in delta and the loads are:
Load 1: 20kVA at 0.85 pf lagging
Load 2: 12kW at 0.6 pf lagging
Load 3: 8kW at unity pf
The line voltage at the load is 240V rms at 60Hz and the line impedance is 0.5 + j0.8 ohms. Determine the line currents and the complex power delivered to the loads.
The loads are balanced three-phase loads that are connected in delta. Each of the loads is given and is connected in delta.
The loads are as follows :Load 1: 20kVA at 0.85 pf 2: 12kW at 0.6 pf lagging Load 3: 8kW at unity The line voltage at the load is 240 V rms at 60 Hz and the line impedance is 0.5 + j0.8 ohms. The line currents can be calculated as follows.
Phase voltage = line voltage / √3= 240/√3= 138.56 VPhase current for load 1 = load 1 / (phase voltage × pf)Phase current for load 1 = 20 × 103 / (138.56 × 0.85)Phase current for load 1 = 182.1 AThe phase current for load 2 can be calculated.
To know more about voltage visit:
https://brainly.com/question/32002804
#SPJ11
Consider a Y-connected AC generator with a number of turns per phase of 600 turns. Find the flux per pole needed to produce the RMS generated line voltage of 4500 Volts at a frequency f-60 Hz. Select one: O a. Flux per pole = 28.2 mWebers O b. Flux per pole = 16.2 mWebers O c. None O d. Flux per pole = 19.85 mWebers O e. Flux per pole = 22.9 mWebers
Given, number of turns per phase, N = 600, RMS generated line voltage, V = 4500 V and frequency, f = 60 Hz. The relationship between RMS generated line voltage, V, frequency, f, and flux per pole, φ is given by the formula,V = 4.44fNφSo, the expression for flux per pole, φ is given by,φ = V / 4.44fNPlugging the given values, we get,φ = 4500 / (4.44 × 60 × 600)φ = 19.85 mWebers Therefore,
the flux per pole needed to produce the RMS generated line voltage of 4500 Volts at a frequency f-60 Hz is 19.85 mWebers.Option (D) is correct.Note: In AC generators, the voltage generated is proportional to the flux per pole, number of turns per phase, and frequency. The above formula is known as the EMF equation of an alternator.
To know more about ac visit:
brainly.com/question/33277960
#SPJ11
During a test on a boiler the following data were recorded:
Pressure = 1.7 MPa
Steam temperature at exit = 240ºC
Steam flow rate = 5.4 tonnes/hour
Fuel consumption = 400 kg/hour
Lower calorific value of fuel = 40 MJ/kg
Temperature of feedwater = 38ºC
Specific heat capacity of superheated steam = 2100 J/kg.K
Specific heat capacity of liquid water = 4200 J/kg.K.
Calculate:
Efficiency of the boiler.
Equivalent evaporation (EE) of the boiler
Given data,Presure P = 1.7 MPaSteam temperature at exit = t2 = 240°CSteam flow rate = m2 = 5.4 tonnes/hourFuel consumption = 400 kg/hourLower calorific value of fuel = LCV = 40 MJ/kgTemperature of feedwater = t1 = 38°CSp. heat capacity of superheated steam = Cp2 = 2100 J/kg.KSp.
Heat capacity of liquid water = Cp1 = 4200 J/kg.K.Formula : Heat supplied = Heat inputFuel consumption, m1 = 400 kg/hourCalorific value of fuel = 40 MJ/kgHeat input, Q1 = m1 × LCV= 400 × 40 × 10³ J/hour = 16 × 10⁶ J/hourFeed water rate, mfw = m2 - m1= 5400 - 4000 = 1400 kg/hourHeat supplied, Q2 = m2 × Cp2 × (t2 - t1)= 5400 × 2100 × (240 - 38) KJ/hour= 10,08 × 10⁶ KJ/hourEfficiency of the boiler, η= (Q2/Q1) × 100= (10.08 × 10⁶)/(16 × 10⁶) × 100= 63 %Equivalent evaporation (EE) of the boilerEE is the amount of water evaporated into steam per hour at the full-load operation at 100 % efficiency.(m2 - m1) × Hvfg= 1400 × 2260= 3.164 × 10⁶ Kg/hour
Therefore, the Efficiency of the boiler is 63 % and Equivalent evaporation (EE) of the boiler is 3.164 × 10⁶ Kg/hour.
To know more about evaporated visit :
https://brainly.com/question/28319650
#SPJ11
Write a function M-file that implements (8) in the interval 0 ≤ t ≤ 55. Note that the initial condition must now be in the form [yo, v0, w0] and the matrix Y, output of ode45, has now three columns (from which y, v and w must be extracted). On the same figure, plot the three time series and, on a separate window, plot the phase plot using figure (2); plot3 (y,v,w); hold on; view ([-40,60]) xlabel('y'); ylabel('vay); zlabel('way''); Do not forget to modify the function defining the ODE. The output is shown in Figure 9. The limits in the vertical axis of the plot on the left were delib- erately set to the same ones as in Figure 8 for comparison purposes, using the MATLAB command ylim ([-2.1,2.1]). You can play around with the 3D phase plot, rotating it by clicking on the circular arrow button in the figure toolbar, but submit the plot with the view value view ([-40, 60]) (that is, azimuth = -40°, elevation = 60°).
The task at hand is to write a function M-file that implements (8) in the interval 0 ≤ t ≤ 55. The initial condition must now be in the form [yo, v0, w0]. The matrix Y, which is the output of ode45, now has three columns. Y(:,1) represents y, Y(:,2) represents v and Y(:,3) represents w. We need to extract these columns.
We also need to plot the three time series on the same figure and, on a separate window, plot the phase plot using figure (2); plot3 (y,v,w); hold on; view ([-40,60]) xlabel('y'); ylabel('vay); zlabel('way'').Here is a function M-file that does what we need:
function [tex]yp = fun(t,y)yp = zeros(3,1);yp(1) = y(2);yp(2) = y(3);yp(3) = -sin(y(1))-0.1*y(3)-0.1*y(2);[/tex]
endWe can now use ode45 to solve the ODE.
The limits in the vertical axis of the plot on the left were deliberately set to the same ones as in Figure 8 for comparison purposes, using the MATLAB command ylim ([-2.1,2.1]). You can play around with the 3D phase plot, rotating it by clicking on the circular arrow button in the figure toolbar, but submit the plot with the view value view ([-40, 60]) (that is, azimuth = -40°, elevation = 60°).
To know more about matrix visit:
https://brainly.com/question/29000721
#SPJ11
Determine the range of K for stability of a unity feedback control system whose open-loop transfer function is K G(s) = K/s(s+ 1)(s + 2)
The range of K for stability of the given control system is $0 < K < 6$. Therefore, the answer is : Range of K for stability of a unity feedback control system whose open-loop transfer function is K G(s) = K/s(s+ 1)(s + 2) is 0 < K < 6.
Given Open loop transfer function: [tex]$$K G(s) = \frac{K}{s(s+ 1)(s + 2)}$$[/tex]
The closed-loop transfer function is given by: [tex]$$\frac{C(s)}{R(s)} = \frac{KG(s)}{1 + KG(s)}$$$$= \frac{K/s(s+ 1)(s + 2)}{1 + K/s(s+ 1)(s + 2)}$$[/tex]
On simplifying, we get: [tex]$$\frac{C(s)}{R(s)} = \frac{K}{s^3 + 3s^2 + 2s + K}$$[/tex]
The characteristic equation of the closed-loop system is: [tex]$$s^3 + 3s^2 + 2s + K = 0$$[/tex]
To obtain a range of values of K for stability, we will apply Routh-Hurwitz criterion. For that we need to form Routh array using the coefficients of s³, s², s and constant in the characteristic equation: $$\begin{array}{|c|c|} \hline s^3 & 1\quad 2 \\ s^2 & 3\quad K \\ s^1 & \frac{6-K}{3} \\ s^0 & K \\ \hline \end{array}$$
For stability, all the coefficients in the first column of the Routh array must be positive: [tex]$$1 > 0$$$$3 > 0$$$$\frac{6-K}{3} > 0$$[/tex]
Hence, [tex]$\frac{6-K}{3} > 0$[/tex] which implies $K < 6$.
So, the range of K for stability of the given control system is $0 < K < 6$.Therefore, the answer is : Range of K for stability of a unity feedback control system whose open-loop transfer function is K G(s) = K/s(s+ 1)(s + 2) is 0 < K < 6.
To know more about closed-loop system, visit:
https://brainly.com/question/11995211
#SPJ11
Which collectors have the highest efficiencies under practical operating conditions?
- Single-glazing
- Double-glazing
- No-glazing
- What is main the idea of using PVT systems?
- What is the maximum temperature obtained in a solar furnace
Double-glazing collectors generally have the highest efficiencies under practical operating conditions.
The main idea of using PVT systems is to harness the combined energy of photovoltaic (PV) and thermal (T) technologies to maximize the overall efficiency and energy output.
The maximum temperature obtained in a solar furnace can reach around 3,000 to 5,000 degrees Celsius.
Double-glazing collectors are known for their superior performance and higher efficiencies compared to single-glazing and no-glazing collectors. This is primarily due to the additional layer of glazing that helps improve thermal insulation and reduce heat losses. The presence of two layers of glass in double-glazing collectors creates an insulating air gap between them, which acts as a barrier to heat transfer. This insulation minimizes thermal losses, allowing the collector to maintain higher temperatures and increase overall efficiency.
The air gap between the glazing layers serves as a buffer, reducing convective heat loss and providing better insulation against external environmental conditions. This feature is especially beneficial in colder climates, where it helps retain the absorbed solar energy within the collector for longer periods. Additionally, the reduced heat loss enhances the collector's ability to generate higher temperatures, making it more effective in various applications, such as space heating, water heating, or power generation.
Compared to single-glazing collectors, the double-glazing design also reduces the direct exposure of the absorber to external elements, such as wind or dust, minimizing the risk of degradation and improving long-term reliability. This design advantage contributes to the overall efficiency and durability of double-glazing collectors.
A solar furnace is a specialized type of furnace that uses concentrated solar power to generate extremely high temperatures. The main idea behind a solar furnace is to harness the power of sunlight and focus it onto a small area to achieve intense heat.
In a solar furnace, sunlight is concentrated using mirrors or lenses to create a highly concentrated beam of light. This concentrated light is then directed onto a target area, typically a small focal point. The intense concentration of sunlight at this focal point results in a significant increase in temperature.
The maximum temperature obtained in a solar furnace can vary depending on several factors, including the size of the furnace, the efficiency of the concentrators, and the materials used in the target area. However, temperatures in a solar furnace can reach several thousand degrees Celsius.
These extremely high temperatures make solar furnaces useful for various applications. They can be used for materials testing, scientific research, and industrial processes that require high heat, such as metallurgy or the production of advanced materials.
A solar furnace is designed to utilize concentrated solar power to generate intense heat. By focusing sunlight onto a small area, solar furnaces can achieve extremely high temperatures. While the exact temperature can vary depending on the specific design and configuration of the furnace, typical solar furnaces can reach temperatures ranging from approximately 3,000 to 5,000 degrees Celsius.
The concentrated sunlight is achieved through the use of mirrors or lenses, which focus the incoming sunlight onto a focal point. This concentrated beam of light creates a highly localized area of intense heat. The temperature at this focal point is determined by the amount of sunlight being concentrated, the efficiency of the concentrators, and the specific materials used in the focal area.
Solar furnaces are employed in various applications that require extreme heat. They are used for materials testing, scientific research, and industrial processes such as the production of advanced materials, chemical reactions, or the study of high-temperature phenomena. The ability of solar furnaces to generate such high temperatures makes them invaluable tools for these purposes.
Learn more about Double-glazing collectors
brainly.com/question/29334038
#SPJ11
i (hydraulic gradient) = 0.0706
D= 3 mm v=0.2345 mis Find Friction factor ? Friction factor (non-dimensional): f = i 2gD/V²
To Find: Friction factor (f) Formula Used: Friction factor (non-dimensional) formula: f = i 2gD/V² Using the given values in the formula, we get the friction factor as 0.3184.
Hydraulic gradient (i) = 0.0706
Diameter of pipe (D) = 3 mm
Velocity of water (V) = 0.2345 m/s
Using the formula for friction factor, f = i 2gD/V²
= (0.0706)2 × 9.81 × 0.003 / (0.2345)²
= 0.01754 / 0.05501
= 0.3184 (approximately)
Therefore, the friction factor (f) is 0.3184. Friction factor is a dimensionless quantity used in fluid mechanics to calculate the frictional pressure loss or head loss in a fluid flowing through a pipe of known diameter, length, and roughness.
Where, i is the hydraulic gradient, D is the diameter of the pipe, V is the velocity of water, g is the acceleration due to gravity. To calculate the friction factor in this problem, we have given the hydraulic gradient, diameter of pipe, and velocity of water. Using the given values in the formula, we get the friction factor as 0.3184.
To know more about visit:
https://brainly.com/question/30168705
#SPJ11
A boundary layer develops with no pressure gradient imposed. The momentum thickness is found to be Θ = δ/4. At some location, the boundary layer thickness is measured to be 8mm. At another location 4mm downstream, the thickness is measured to be 16 mm. Use the momentum integral equation to estimate the value of the skin-friction coefficient C’f, in the vicinity of these two measurements.
The value of the skin-friction coefficient C’ f in the vicinity of these two measurements using the momentum integral equation is 0.0031.
The thickness of the boundary layer grows due to the movement of the fluid and, to some extent, the shear stresses produced as the fluid moves across a surface. No pressure gradient has been imposed in this scenario, implying that the fluid velocity is entirely determined by the local shear stresses within the fluid.
According to the question, Θ = δ/4, where Θ is the momentum thickness. This indicates that the momentum thickness is a quarter of the displacement thickness, δ. To use the momentum integral equation, the value of the momentum thickness must be found first. According to the problem statement, the momentum thickness is given as Θ = δ/4.
To know more coefficient visit:-
https://brainly.com/question/16546282
#SPJ11
A centrifugal pump may be viewed as a vortex, where the 0.4m diameter impeller, rotates within a 1m diameter casing at a speed of 200 rpm.
Determine
The circumferential velocity, in m/s at a radius of 0.45 m
A centrifugal pump may be viewed as a vortex.
It consists of an impeller that rotates within a casing.
The impeller's diameter is 0.4m and rotates within a 1m diameter casing at a speed of 200rpm.
To determine the circumferential velocity, use the formula provided below:
Formula:
Circumferential velocity (v) = 2π x Radius (r) x Rotational Speed (N) / 60
Given:
Radius (r) = 0.45 m
Rotational speed
(N) = 200 rpm
Diameter of impeller = 0.4m
Diameter of casing = 1m
Solution:
Circumference of the impeller= π
diameter= π x 0.4 m
= 1.2566 m
Therefore,
Circumferential velocity (v) = 2π x Radius (r) x Rotational Speed (N) / 60
= (2 x π x 0.45 m x 200 rpm) / 60
= (0.1414 x 200) m/s
= 28.28 m/s
Therefore, the circumferential velocity at a radius of 0.45 m is 28.28 m/s.
To know more about Rotational visit:
https://brainly.com/question/1571997
#SPJ11
11kg of R-134a at 320kPa fills a rigid tank whose volume is 0.011m³. Find the quality, the temperature, the total internal energy and enthalpy of the system. If the container heats up and the pressure reaches to 600kPa, find the temperature, total energy and total enthalpy at the end of the process.
The quality, temperature, total internal energy, and enthalpy of the system are given by T2 is 50.82°C (final state) and U1 is 252.91 kJ/kg (initial state) and U2 is 442.88 kJ/kg (final state) and H1 277.6 kJ/kg (initial state) and H2 is 484.33 kJ/kg (final state).
Given data:
Mass of R-134a (m) = 11kg
The pressure of R-134 at an initial state
(P1) = 320 kPa Volume of the container (V) = 0.011 m³
The formula used: Internal energy per unit mass (u) = h - Pv
Enthalpy per unit mass (h) = u + Pv Specific volume (v)
= V/m Quality (x) = (h_fg - h)/(h_g - h_f)
1. To find the quality of R-134a at the initial state: From the steam table, At 320 kPa, h_g = 277.6 kJ/kg, h_f = 70.87 kJ/kgh_fg = h_g - h_f= 206.73 kJ/kg Enthalpy of the system at initial state (H1) can be calculated as H1 = h_g = 277.6 kJ/kg Internal energy of the system at initial state (U1) can be calculated as:
U1 = h_g - Pv1= 277.6 - 320*10³*0.011 / 11
= 252.91 kJ/kg
The quality of R-134a at the initial state (x1) can be calculated as:
x1 = (h_fg - h1)/(h_g - h_f)
= (206.73 - 277.6)/(277.6 - 70.87)
= 0.5
The volume of the container is rigid, so it will not change throughout the process.
2. To find the temperature, total internal energy, and total enthalpy at the final state:
Using the values from an initial state, enthalpy at the final state (h2) can be calculated as:
h2 = h1 + h_fg
= 277.6 + 206.73
= 484.33 kJ/kg So the temperature of R-134a at the final state is approximately 50.82°C. The total enthalpy of the system at the final state (H2) can be calculated as,
= H2
= 484.33 kJ/kg
Thus, the quality, temperature, total internal energy, and enthalpy of the system are given by:
x1 = 0.5 (initial state)T2 = 50.82°C (final state) U1 = 252.91 kJ/kg (initial state) U2 = 442.88 kJ/kg (final state) H1 = 277.6 kJ/kg (initial state)H2 = 484.33 kJ/kg (final state)
To know more about enthalpy please refer:
https://brainly.com/question/826577
#SPJ11
Design a three stepped distance protection for the protection of an EHV transmission line. Explain / label all the steps and constraints using circuit diagram(s) as well. Put together your proposed scheme considering the trip contacts configuration of the circuit breaker(s).
Distance protection is a type of protection scheme used in power system transmission line protection. It provides good selectivity and sensitivity in identifying the faulted section of the line.
The main concept of distance protection is to compare the voltage and current of the protected line and calculate the distance to the fault. This protection is widely used in Extra High Voltage (EHV) transmission lines. Design of three-stepped distance protection: Three-stepped distance protection for the EHV transmission line can be designed using the following steps:
Step 1: Zone 1 protection For the first step, we use the distance relay to provide Zone 1 protection. This relay is located at the beginning of the transmission line, and its reach is set to cover the full length of the line plus the length of the adjacent feeder. The relay uses the phase-to-phase voltage (Vab, Vbc, Vca) and the three-phase current (Ia, Ib, Ic) to measure the impedance of the line. If the calculated impedance falls below a set threshold, the relay trips the circuit breaker. The circuit diagram of Zone 1 protection is as follows:
Step 2: Zone 2 protection For the second step, we use the distance relay to provide Zone 2 protection. This relay is located at a distance from the substation, and its reach is set to cover the full length of the transmission line plus a margin. The relay uses the phase-to-phase voltage (Vab, Vbc, Vca) and the three-phase current (Ia, Ib, Ic) to measure the impedance of the line. If the calculated impedance falls below a set threshold, the relay trips the circuit breaker. The circuit diagram of Zone 2 protection is as follows:
Step 3: Backup protection For the third step, we use the overcurrent relay to provide backup protection. This relay is located at the substation and uses the current of the transmission line to measure the fault current. If the fault current exceeds a set threshold, the relay trips the circuit breaker. The circuit diagram of the backup protection is as follows:
Constraints: There are some constraints that we need to consider while designing three-stepped distance protection for the EHV transmission line. These are as follows:• The reach of each zone should be set appropriately to avoid false tripping and ensure proper selectivity.• The time delay of each zone should be coordinated to avoid overreach.• The CT ratio and PT ratio should be chosen such that the relay operates correctly.• The trip contact configuration of the circuit breaker should be considered while designing the protection scheme.
To know more about Distance protection visit:
https://brainly.com/question/31914334
#SPJ11
9) Show that a positive logic NAND gate is a negative logic NOR gate and vice versa.
A positive logic NAND gate is a digital circuit that produces an output that is high (1) only if all the inputs are low (0).
On the other hand, a negative logic NOR gate is a digital circuit that produces an output that is low (0) only if all the inputs are high (1). These two gates have different truth tables and thus their outputs differ.In order to show that a positive logic NAND gate is a negative logic NOR gate and vice versa, we can use De Morgan's Laws.
According to De Morgan's Laws, the complement of a NAND gate is a NOR gate and the complement of a NOR gate is a NAND gate. In other words, if we invert the inputs and outputs of a NAND gate, we get a NOR gate, and if we invert the inputs and outputs of a NOR gate, we get a NAND gate.
Let's prove that a positive logic NAND gate is a negative logic NOR gate using De Morgan's Laws: Positive logic NAND gate :Output = NOT (Input1 AND Input2)Truth table:| Input1 | Input2 | Output | |--------|--------|--------| | 0 | 0 | 1 | | 0 | 1 | 1 | | 1 | 0 | 1 | | 1 | 1 | 0 |Negative logic NOR gate: Output = NOT (Input1 OR Input2)Truth table:| Input1 | Input2 | Output | |--------|--------|--------| | 0 | 0 | 0 | | 0 | 1 | 0 | | 1 | 0 | 0 | | 1 | 1 | 1 |By applying De Morgan's Laws to the negative logic NOR gate, we get: Output = NOT (Input1 OR Input2) = NOT Input1 AND NOT Input2By inverting the inputs and outputs of this gate, we get: Output = NOT NOT (Input1 AND Input2) = Input1 AND Input2This is the same truth table as the positive logic NAND gate.
Therefore, a positive logic NAND gate is a negative logic NOR gate. The vice versa is also true.
To know more about positive visit :
https://brainly.com/question/23709550
#SPJ11
Two -in-thick steel plates with a modulus of elasticity of 30(106) psi are clamped by washer-faced -in-diameter UNC SAE grade 5 bolts with a 0.095-in-thick washer under the nut. Find the member spring rate km using the method of conical frusta, and compare the result with the finite element analysis (FEA) curve-fit method of Wileman et al.
The spring rate found using the method of conical frusta is slightly higher than that obtained using the Finite element analysis (FEA) curve-fit method of Wileman et al.
The spring rate using this method is found to be 1.1 x 10⁶ psi.
Given Information:
Thickness of steel plates, t = 2 in
Diameter of UNC SAE grade 5 bolts, d = 0.75 in
Thickness of washer, e = 0.095 in
Modulus of Elasticity, E = 30 × 10⁶ psi
Formula:
Member spring rate km = 2.1 x 10⁶ (d/t)²
Where, Member spring rate km
Method of conical frusta:
=2.1 x 10⁶ (d/t)²
Comparison method
Finite element analysis (FEA) curve-fit method of Wileman et al.
Calculation:
The member spring rate is given by
km = 2.1 x 10⁶ (d/t)²
For given steel plates,t = 2 in
d = 0.75 in
Therefore,
km = 2.1 x 10⁶ (d/t)²
(0.75/2)²= 1.11375 x 10⁶ psi
As per the given formula, the spring rate using the method of conical frusta is 1.11375 x 10⁶ psi.
The comparison method is the Finite element analysis (FEA) curve-fit method of Wileman et al.
The spring rate using this method is found to be 1.1 x 10⁶ psi.
To know more about Modulus of Elasticity, visit:
https://brainly.com/question/30756002
#SPJ11
A cylindrical specimen of some metal alloy 10 mm in diameter is stressed elastically in tension. A force of 10,000 N produces a reduction in specimen diameter of 2 × 10^-3 mm. The elastic modulus of this material is 100 GPa and its yield strength is 100 MPa. What is the Poisson's ratio of this material?
A cylindrical specimen of some metal alloy 10 mm in diameter is stressed elastically in tension.A force of 10,000 N produces a reduction in specimen diameter of 2 × 10^-3 mm.
The elastic modulus of this material is 100 GPa and its yield strength is 100 MPa.Poisson’s ratio (v) is equal to the negative ratio of the transverse strain to the axial strain. Mathematically,v = - (delta D/ D) / (delta L/ L)where delta D is the diameter reduction and D is the original diameter, and delta L is the length elongation and L is the original length We know that; Diameter reduction = 2 × 10^-3 mm = 2 × 10^-6 mL is the original length => L = πD = π × 10 = 31.42 mm.
The axial strain = delta L / L = 0.0032/31.42 = 0.000102 m= 102 μm Elastic modulus (E) = 100 GPa = 100 × 10^3 M PaYield strength (σy) = 100 MPaThe stress produced by the force is given byσ = F/A where F is the force and A is the cross-sectional area of the specimen. A = πD²/4 = π × 10²/4 = 78.54 mm²σ = 10,000/78.54 = 127.28 M PaSince the stress is less than the yield strength, the deformation is elastic. Poisson's ratio can now be calculated.v = - (delta D/ D) / (delta L/ L)= - 2 × 10^-6 / 10 / (102 × 10^-6) = - 0.196Therefore, the Poisson's ratio of this material is -0.196.
To know more about thermal conduction visit:
brainly.com/question/33285621
#SPJ11
A ship, travelling at 12 knots, has an autopilot system with a time and gain constants of 107 s and 0.185 s⁻¹, respectively. The autopilot moves the rudder heading linearly from 0 to 15 degrees over 1 minute. Determine the ships heading, in degrees, after 1 minute.
The ship's heading, in degrees, after 1 minute can be determined by considering the autopilot system's time and gain constants, as well as the rudder heading range. Using the given information and the rate of change in heading, we can calculate the ship's heading after 1 minute.
The autopilot system's time constant of 107 s represents the time it takes for the system's response to reach 63.2% of its final value. The gain constant of 0.185 s⁻¹ determines the rate at which the system responds to changes. Since the autopilot moves the rudder heading linearly from 0 to 15 degrees over 1 minute, we can calculate the ship's heading at the end of 1 minute. Given that the rudder heading changes linearly, we can divide the total change in heading (15 degrees) by the time taken (1 minute) to determine the rate of change in heading.
Learn more about rudder here:
https://brainly.com/question/27274213
#SPJ11
Which statement is not correct about heat convection for external flow?
A. The flow pattern over the tube bundle is different from the single tube.
B. The same correlation for the Nusselt number can be used for cylinders and spheres.
C. The flow pattern over the tube bundle with aligned (in-line) configuration is different from that with staggered configuration.
D. The fluid thermophysical properties are usually evaluated at the film temperature, which is the average of the surface and the mainstream temperatures.
A statement which not correct about heat convection for external flow is The same correlation for the Nusselt number can be used for cylinders and spheres.
The correct option is B)
What is heat convection?Heat convection is a mechanism in which thermal energy is transferred from one place to another by moving fluids, including gases and liquids. Heat transfer occurs in fluids through advection or forced flow, natural convection, or radiation.
Convection in external flow is caused by forced flow over an object. The fluid moves over the object, absorbing heat and carrying it away. The rate at which heat is transferred in forced flow depends on the velocity of the fluid, the thermodynamic and transport properties of the fluid, and the size and shape of the object
.The Nusselt number can be calculated to understand the relationship between heat transfer, fluid properties, and object characteristics. However, the same Nusselt number correlation cannot be used for both cylinders and spheres since the flow pattern varies significantly. This is why option B is not correct.
As a result, option B, "The same correlation for the Nusselt number can be used for cylinders and spheres," is not correct about heat convection for external flow.
Learn more about convection at
https://brainly.com/question/9535726
#SPJ11
A rectangular slit is 200 mm wide and has a height of 1000 mm. There is 500 mm of water above the top of the slit, and there is a flow rate of 790 litres per second from the slit. Calculate the discharge coefficient of the slit.
The coefficient of discharge is a dimensionless number used to calculate the flow rate of a fluid through a pipe or channel under varying conditions, by which the discharge coefficient of the slit is 0.65
How to find?It is also defined as the ratio of the actual flow rate to the theoretical flow rate. A rectangular slit is 200 mm wide and has a height of 1000 mm. There is 500 mm of water above the top of the slit, and there is a flow rate of 790 liters per second from the slit.
We need to determine the discharge coefficient of the slit.
Given:
Width of slit = 200 mm
Height of slit = 1000 mm
Depth of water above the slit = 500 mm
Flow rate = 790 liters/sec
Formula Used:
Coefficient of Discharge = Q / A√2gH
Where, Q = Flow rate
A = Cross-sectional area of the opening
g = Acceleration due to gravity
H = Depth of liquid above the opening√2 = Constant
Substitute the given values, then,
Discharge (Q) = 790 liters/sec
= 0.79 m³/s
Width (b) = 200 mm
= 0.2 m
Height (h) = 1000 mm
= 1 m
Depth of liquid (H) = 500 mm
= 0.5 mA
= bh
= 0.2 × 1
= 0.2 m²g
= 9.81 m/s².
Substituting these values in the above equation, we have;
C = Q/A√2g
HC = (0.79 / 0.2 √2 × 9.81 × 0.5)
C = 0.65:
The discharge coefficient of the slit is 0.65.
To know more on coefficient visit:
https://brainly.com/question/1594145
#SPJ11
Steam enters the high-pressure turbine of a steam power plant that operates on the ideal reheat Rankine cycle at 6 MPa and 500°C and leaves as saturated vapor. Steam is then reheated to 400°C before it expands to a pressure of 10 kPa. Heat is transferred to the steam in the boiler at a rate of 6 × 104 kW. Steam is cooled in the condenser by the cooling water from a nearby river, which enters the condenser at 7°C. Show the cycle on a T-s diagram with respect to saturation lines, and determine (a) the pressure at which reheating takes place, (b) the net power output and thermal efficiency, and (c) the minimum mass flow rate of the cooling water required. mains the same
a) Pressure at which reheating takes place The given steam power plant operates on the ideal reheat Rankine cycle. Steam enters the high-pressure turbine at 6 MPa and 500°C and leaves as saturated vapor.
The cycle on a T-s diagram with respect to saturation lines can be represented as shown below :From the above diagram, it can be observed that the steam is reheated between 6 MPa and 10 kPa. Therefore, the pressure at which reheating takes place is 10 kPa .
b) Net power output and thermal efficiency The net power output of the steam power plant can be given as follows: Net Power output = Work done by the turbine – Work done by the pump Work done by the turbine = h3 - h4Work done by the pump = h2 - h1Net Power output = h3 - h4 - (h2 - h1)Thermal efficiency of the steam power plant can be given as follows: Thermal Efficiency = (Net Power Output / Heat Supplied) x 100Heat supplied =[tex]6 × 104 kW = Q1 + Q2 + Q3h1 = hf (7°C) = 5.204 kJ/kgh2 = hf (10 kPa) = 191.81 kJ/kgh3 = hg (6 MPa) = 3072.2 kJ/kgh4 = hf (400°C) = 2676.3 kJ/kgQ1 = m(h3 - h2) = m(3072.2 - 191.81) = 2880.39m kJ/kgQ2 = m(h4 - h1) = m(26762880.39m - 2671.09m = 209.3m x 100= [209.3m / (2880.39m + 2671.09m)] x 100= 6.4 %c)[/tex]
Minimum mass flow rate of the cooling water required Heat rejected by the steam to the cooling water can be given as follows: Q rejected = mCpΔTwhere m is the mass flow rate of cooling water, Cp is the specific heat capacity of water, and ΔT is the temperature difference .Qrejected = Q1 - Q2 - Q3 = 209.3 m kW Q rejected = m Cp (T2 - T1)where T2 = temperature of water leaving the condenser = 37°C, T1 = temperature of water entering the condenser = 7°C, and Cp = 4.18 kJ/kg K Therefore, m = Qrejected / (Cp (T2 - T1))= 209.3 x 103 / (4.18 x 30)= 1.59 x 103 kg/s = 1590 kg/s Thus, the minimum mass flow rate of cooling water required is 1590 kg/s.
To know more about saturated vapor visit:
brainly.com/question/32499566
#SPJ11
The pressure and temperature at the beginning of the compression of a dual cycle are 101 kPa and 15 ºC.
The compression ratio is 12. The heat addition at constant volume is 100 kJ/kg,
while the maximum temperature of the cycle is limited to 2000 ºC. air mass
contained in the cylinder is 0.01 kg. Determine a) the maximum cycle pressure, the MEP, the
amateur heat, the heat removed, the added compression work, the work of
expansion produced, the net work produced and the efficiency of the cycle.
The maximum temperature is 662.14 K.
The maximum cycle pressure is 189.69 kPa.
The Mean Effective Pressure (MEP) is 0.242 kJ and the net heat addition (Qin) is 1 kJ.
1. Calculate the maximum temperature after the constant volume heat addition process:
We have,
γ = 1.4 (specific heat ratio)
[tex]T_1[/tex] = 15 ºC + 273.15 = 288.15 K (initial temperature)
[tex]T_3[/tex]= 2000 ºC + 273.15 = 2273.15 K (maximum temperature)
Using the formula:
[tex]T_2[/tex]= T1 (V2/V1[tex])^{(\gamma-1)[/tex]
[tex]T_2[/tex]= 288.15 K [tex]12^{(1.4-1)[/tex]
So, T2 = 288.15 K x [tex]12^{0.4[/tex]
[tex]T_2[/tex] ≈ 288.15 K * 2.2974
[tex]T_2[/tex]≈ 662.14 K
2. Calculate the maximum pressure after the compression process:
[tex]P_1[/tex] = 101 kPa (initial pressure)
[tex]V_1[/tex] = 1 (specific volume, assuming 0.01 kg of air)
Using the ideal gas law equation:
P = 101 kPa * (662.14 K / 288.15 K) * (1 / 12)
P ≈ 189.69 kPa
Therefore, the maximum cycle pressure is 189.69 kPa.
3. [tex]T_2[/tex]≈ 662.14 K
and, Qin = Qv * m
Qin = 100 kJ/kg * 0.01 kg
Qin = 1 kJ
So, Wc = m * Cv * (T2 - T1)
Wc ≈ 0.01 kg * 0.718 kJ/kg·K * 373.99 K
Wc ≈ 2.66 kJ
and, MEP = Wc / (r - 1)
MEP = 2.66 kJ / (12 - 1)
MEP ≈ 2.66 kJ / 11
MEP ≈ 0.242 kJ
Therefore, the Mean Effective Pressure (MEP) is 0.242 kJ and the net heat addition (Qin) is 1 kJ.
Learn more about Mean Effective Pressure here:
https://brainly.com/question/32661939
#SPJ4
Compute the Fourier Series decomposition of a square waveform with 90% duty cycle
The Fourier series decomposition of the square waveform with a 90% duty cycle is given by: f(t) = (a0/2) + ∑[(an * cos((2πnt)/T)) + (bn * sin((2πnt)/T))]
The Fourier series decomposition for a square waveform with a 90% duty cycle:
Definition of the Square Waveform:
The square waveform with a 90% duty cycle is defined as follows:
For 0 ≤ t < T0.9 (90% of the period), the waveform is equal to +1.
For T0.9 ≤ t < T (10% of the period), the waveform is equal to -1.
Here, T represents the period of the waveform.
Fourier Series Coefficients:
The Fourier series coefficients for this waveform can be computed using the following formulas:
a0 = (1/T) ∫[0 to T] f(t) dt
an = (2/T) ∫[0 to T] f(t) cos((2πnt)/T) dt
bn = (2/T) ∫[0 to T] f(t) sin((2πnt)/T) dt
where a0, an, and bn are the Fourier coefficients.
Computation of Fourier Coefficients:
For the given square waveform with a 90% duty cycle, we have:
a0 = (1/T) ∫[0 to T] f(t) dt = 0 (since the waveform is symmetric around 0)
an = 0 for all n ≠ 0 (since the waveform is symmetric and does not have cosine terms)
bn = (2/T) ∫[0 to T] f(t) sin((2πnt)/T) dt
Computation of bn for n = 1:
We need to compute bn for n = 1 using the formula:
bn = (2/T) ∫[0 to T] f(t) sin((2πt)/T) dt
Breaking the integral into two parts (corresponding to the two regions of the waveform), we have:
bn = (2/T) [∫[0 to T0.9] sin((2πt)/T) dt - ∫[T0.9 to T] sin((2πt)/T) dt]
Evaluating the integrals, we get:
bn = (2/T) [(-T0.9/2π) cos((2πt)/T)] from 0 to T0.9 - (-T0.1/2π) cos((2πt)/T)] from T0.9 to T
bn = (2/T) [(T - T0.9)/2π - (-T0.9)/2π]
bn = (T - T0.9)/π
Fourier Series Decomposition:
The Fourier series decomposition of the square waveform with a 90% duty cycle is given by:
f(t) = (a0/2) + ∑[(an * cos((2πnt)/T)) + (bn * sin((2πnt)/T))]
However, since a0 and an are 0 for this waveform, the decomposition simplifies to:
f(t) = ∑[(bn * sin((2πnt)/T))]
For n = 1, the decomposition becomes:
f(t) = (T - T0.9)/π * sin((2πt)/T)
This represents the Fourier series decomposition of the square waveform with a 90% duty cycle, including the computation of the Fourier coefficients and the final decomposition expression for the waveform.
To know more about waveform, visit:
https://brainly.com/question/26058582
#SPJ11
Calculate the peak solar hours in the area with
illumination of 5300 (PSH). Watts / day
The peak solar hours in the area with illumination of 5300 watts/day would be 5.3 PSH.
Peak solar hours refer to the amount of solar energy that an area receives per day. It is calculated based on the intensity of sunlight and the length of time that the sun is shining.
In this case, the peak solar hours in an area with an illumination of 5300 watts/day can be calculated as follows:
1. Convert watts to kilowatts by dividing by 1000: 5300/1000 = 5.3 kW2. Divide the total energy generated by the solar panels in a day (5.3 kWh) by the average power generated by the solar panels during the peak solar hours:
5.3 kWh ÷ PSH = Peak Solar Hours (PSH)For example,
if the average power generated by the solar panels during peak solar hours is 1 kW, then the PSH would be:5.3 kWh ÷ 1 kW = 5.3 PSH
To know more about illumination visit:
https://brainly.com/question/29156148
#SPJ11
Explain briefly the advantages" and "disadvantages of the "Non ferrous metals and alloys" in comparison with the "Ferrous alloys (15p). Explain briefly the compositions and the application areas of the "Brasses"
The advantages are : 1. Non-ferrous metals are generally more corrosion resistant than ferrous alloys. 2. They are also more lightweight and have a higher melting point. 3. Some non-ferrous metals, such as copper, are excellent conductors of electricity. The disadvantages are : 1. Non-ferrous metals are typically more expensive than ferrous alloys. 2. They are also more difficult to machine and weld. 3. Some non-ferrous metals, such as lead, are toxic.
Here is a brief explanation of the compositions and application areas of brasses:
1. Brasses are copper-based alloys that contain zinc.
2. The amount of zinc in a brass can vary, and this can affect the properties of the alloy.
3. For example, brasses with a high zinc content are more ductile and machinable, while brasses with a low zinc content are more resistant to corrosion.
4. Brasses are used in a wide variety of applications, including:
Electrical connectors
Plumbing fixtures
Musical instruments
Jewelry
Coins
To learn more about Plumbing fixtures click here : brainly.com/question/30001133
#SPJ11
Suppose an infinitely large plane which is flat. It is positively charged with a uniform surface density ps C/m²
1. Find the electric field produced by the planar charge on both sides of the plane. If you use symmetry argument you may picture the field lines. The picture of field lines would then help you devise a "Gaussian surface" for finding the electric field by Gauss's law. 2. Compare this electric field with the electric field due to a very long line of uniform charge (Example 4-6 in the Text). 3. Now imagine there are two planar sheets with charges. One is charged with a uniform surface density p. and the other -P. The two planes are placed in parallel with a distance d apart. Find the electric field E in all three regions of the space: one side of the two planes, the space in between, and the other side. Superposition principle would be useful for finding the field.
Suppose an infinitely large plane which is flat. It is positively charged with a uniform surface density ps C/m²
As the plane is infinitely large and flat, the electric field produced by it on both sides of the plane will be uniform.
1. Electric field due to the planar charge on both sides of the plane:
The electric field due to an infinite plane of charge is given by the following equation:
E = σ/2ε₀, where E is the electric field, σ is the surface charge density, and ε₀ is the permittivity of free space.
Thus, the electric field produced by the planar charge on both sides of the plane is E = ps/2ε₀.
We can use the symmetry argument to picture the field lines. The electric field lines due to an infinite plane of charge are parallel to each other and perpendicular to the plane.
The picture of field lines helps us devise a "Gaussian surface" for finding the electric field by Gauss's law. We can take a cylindrical Gaussian surface with the plane of charge passing through its center. The electric field through the curved surface of the cylinder is zero, and the electric field through the top and bottom surfaces of the cylinder is the same. Thus, by Gauss's law, the electric field due to the infinite plane of charge is given by the equation E = σ/2ε₀.
2. Comparison between electric fields due to the plane and the long line of uniform charge:
The electric field due to a long line of uniform charge with linear charge density λ is given by the following equation:
E = λ/2πε₀r, where r is the distance from the line of charge.
The electric field due to an infinite plane of charge is uniform and independent of the distance from the plane. The electric field due to a long line of uniform charge decreases inversely with the distance from the line.
Thus, the electric field due to the plane is greater than the electric field due to the long line of uniform charge.
3. Electric field due to two planar sheets with charges:
Let's assume that the positive charge is spread on the plane with a surface density p, and the negative charge is spread on the other plane with a surface density -P.
a. One side of the two planes:
The electric field due to the positive plane is E1 = p/2ε₀, and the electric field due to the negative plane is E2 = -P/2ε₀. Thus, the net electric field on one side of the two planes is E = E1 + E2 = (p - P)/2ε₀.
b. The space in between:
Inside the space in between the two planes, the electric field is zero because there is no charge.
c. The other side of the two planes:
The electric field due to the positive plane is E1 = -p/2ε₀, and the electric field due to the negative plane is E2 = P/2ε₀. Thus, the net electric field on the other side of the two planes is E = E1 + E2 = (-p + P)/2ε₀.
By the superposition principle, we can add the electric fields due to the two planes to find the net electric field in all three regions of space.
Learn more about electric fields: https://brainly.com/question/19878202
#SPJ11
A cantilever beam has length 24 in and a force of 2000 lbf at the free end. The material is A36/. For a factor of safety of 2, find the required cross section dimensions of the beam. The cross section can be assumed as square, rectangular, pipe or I-beam.
The formula for the shear stress in a cantilever beam subjected to a transverse force can be used to find the required cross-section dimensions for the beam.The formula is; τmax = VQ/ItWhere;V = the maximum force (2000 lbs.)Q = the first moment of the area around the neutral axis.
I = the moment of inertia.The maximum shear stress for A36 steel is 20,000 psi. For a factor of safety of 2, this value can be doubled to 40,000 psi.So,τmax = VQ/It = 40000 psi.The dimensions of the beam can be found using the shear stress equation and the bending moment equation.
Mmax = PL/4 = 2000 lbs. × 24 in./4 = 12000 in. lbs.τmax = Mmax*c/I = 40000 psiThe required cross-section dimensions of the beam can be found as follows;For a square beam;a = b ⇒ c = a / √6P = 12000 lbs.
[tex]Q = b × h × h / 2 = a × a × a / 2√3h = a/√3I = a^4/12c = I × τmax / b × h²a = (6 × P / (τmax × h²))^(1/4).[/tex]
For a rectangular beam;
[tex]a < b ⇒ c = a / √6P = 12000 lbs.Q = b × h × h / 2 = a × b × b / 2h = √(2a / 3)I = ab^3/12c = I × τmax / b × h²a = (6 × P / (τmax × h² × b))^(1/3) × b^2/3.[/tex]
For a pipe;a = b and D = 2rP = 12000 lbs.τavg = P/ (2A - a²) = 40000 psiThe diameter of the pipe can be found using the following equation;
[tex]r = (P/2τavg)(D² - d²)/D²d = D - 2ta = πr² - πr²/4A = πr²D = 2r(1 + (4a²/(πr^2))^(1/2)).[/tex]
For an I-beam;the required dimensions can be found by assuming that the beam is an equivalent rectangular beam and then using the above rectangular beam formula. In the equivalent rectangular beam, the width of the flanges is equal to the thickness of the web multiplied by a factor of 1.2 to 1.5. The thickness of the web is taken as the distance between the midpoints of the flanges.
From the above, we can conclude that the cross-section dimensions of a square beam, rectangular beam, pipe, and I-beam can be found.
To know more about shear stress :
brainly.com/question/12910262
#SPJ11
Q5. The stream function for a certain flow field is Y = 2y2 – 2x2 + 5 = - a) Determine the corresponding velocity potential
The velocity potential is given by ϕ = 2y² - 5.
The stream function for a flow field is given by Y = 2y² - 2x² + 5 = -
Now let's differentiate the equation in terms of x to obtain the velocity potential given by the following relation:
∂Ψ/∂x = - ∂ϕ/∂y
where Ψ = stream function
ϕ = velocity potential
∂Ψ/∂x = -4x and ∂ϕ/∂y = 4y
Hence we can integrate ∂ϕ/∂y with respect to y to get the velocity potential.
∂ϕ/∂y = 4yϕ = 2y² + c where c is a constant to be determined since the velocity potential is only unique up to a constant. c can be obtained from the stream function Y = 2y² - 2x² + 5 = -ϕ = 2y² - 5 and the velocity potential
Therefore the velocity potential is given by ϕ = 2y² - 5.
The velocity potential of the given stream function has been obtained.
To know more about velocity visit
brainly.com/question/30559316
#SPJ11
A connecting rod of length /= 11.67in has a mass m3 = 0.0234blob. Its mass moment of inertia is 0.614 blob-in². Its CG is located 0.35/ from the crank pin, point A. A crank of length r= 4.132in has a mass m₂ = 0.0564blob. Its mass moment of inertia about its pivot is 0.78 blob-in². Its CG is at 0.25r from the main pin, O₂. The piston mass= 1.012 blob. The thickness of the cylinder wall is 0.33in, and the Bore (B) is 4in. The gas pressure is 500psi. The linkage is running at a constant speed 1732rpm and crank position is 37.5°. If the crank has been exact static balanced with a mass equal to me and balance radius of r, what is the inertia force on the Y-direction?
The connecting rod's mass moment of inertia is 0.614 blob-in², and its mass m3 is 0.0234blob.
Its CG is located 0.35r from the crank pin, point A.
The crank's length is r = 4.132in, and its mass is m₂ = 0.0564blob, and its CG is at 0.25r from the main pin, O₂.
The thickness of the cylinder wall is 0.33in, and the Bore (B) is 4in.
The piston mass is 1.012 blob.
The gas pressure is 500psi.
The linkage is running at a constant speed of 1732 rpm, and the crank position is 37.5°.
If the crank is precisely static balanced with a mass equal to me and a balanced radius of r, the inertia force on the Y-direction will be given as;
I = Moment of inertia of the system × Angular acceleration of the system
I = [m3L3²/3 + m2r2²/2 + m1r1²/2 + Ic] × α
where,
Ic = Mass moment of inertia of the crank about its pivot
= 0.78 blob-in²m1
= Mass of the piston
= 1.012 blob
L = Length of the connecting rod
= 11.67 inr
1 = Radius of the crank pin
= r
= 4.132 inm
2 = Mass of the crank
= 0.0564 blob
α = Angular acceleration of the system
= (2πn/60)²(θ2 - θ1)
where, n = Engine speed
= 1732 rpm
θ2 = Final position of the crank
= 37.5° in radians
θ1 = Initial position of the crank
= 0° in radians
Substitute all the given values into the above equation,
I = [(0.0234 x 11.67²)/3 + (0.0564 x 4.132²)/2 + (1.012 x 4.132²)/2 + 0.614 + 0.0564 x r²] x (2π x 1732/60)²(37.5/180π - 0)
I = [0.693 + 1.089 + 8.464 + 0.614 + 0.0564r²] x 41.42 x 10⁶
I = 3.714 + 5.451r² × 10⁶ lb-in²-sec²
Now, inertia force along the y-axis is;
Fy = Iω²/r
Where,
ω = Angular velocity of the system
= (2πn/60)
where,
n = Engine speed
= 1732 rpm
Substitute all the values into the above equation;
Fy = [3.714 + 5.451r² × 10⁶] x (2π x 1732/60)²/r
Fy = (7.609 x 10⁹ + 1.119r²) lb
To know more about velocity visit:
https://brainly.com/question/30559316
#SPJ11
ie lbmol of pentane gas (C₅H₁₂) reacts with the theoretical amount of air in a closed, rigid tank. Initially, the reactants are at 77°F, 1 m. After complete combustion, the temperature in the tank is 1900°R. Assume air has a molar analysis of 21% O₂ and 79% N₂. Determine the heat transfer, in Btu. Q = i Btu
The heat transfer, Q, can be calculated using the equation:
Q = ΔHc + ΔHg. To determine the heat transfer in Btu for the given scenario, we need to calculate the heat released during the combustion of pentane and the subsequent increase in temperature of the gases in the tank.
Where ΔHc is the heat released during combustion and ΔHg is the heat gained by the gases in the tank due to the increase in temperature. To calculate ΔHc, we need to determine the moles of pentane reacted and the heat of combustion per mole of pentane. Since pentane reacts with air, we also need to consider the moles of oxygen available in the air. The heat of combustion of pentane can be obtained from reference sources. To calculate ΔHg, we can use the ideal gas law and the given initial and final temperatures, along with the molar analysis of air, to determine the change in enthalpy. By summing up ΔHc and ΔHg, we can obtain the total heat transfer, Q, in Btu. It's important to note that the actual calculations involve several steps and equations, including stoichiometry, enthalpy calculations, and gas laws. The specific values and formulas needed for the calculations are not provided in the question, so an exact numerical result cannot be determined without that information.
Learn more about stoichiometry here:
https://brainly.com/question/28780091
#SPJ11
An inductor L, resistor R, of value 52 and resistor R. of value 102 are connected in series with a voltage source of value V(t) = 50 cos cot. If the power consumed by the R, resistor is 10 W. calculate the power factor of the circuit. [5 Marks]
Resistance of R1, R = 52 Ω
Resistance of R2, R = 102 Ω
Voltage source, V(t) = 50 cos (ωt)
Power consumed by R1, P = 10 W
We know that the total power consumed by the circuit is given as, PT = PR1 + PR2 + PL Where, PL is the power consumed by the inductor. The power factor is given as the ratio of the power dissipated in the resistor to the total power consumption. Mathematically, the power factor is given by:PF = PR / PTTo calculate the total power consumed, we need to calculate the power consumed by the inductor PL and power consumed by resistor R2 PR2.
First, let us calculate the impedance of the circuit. Impedance, Z = R + jωL
Here, j = √(-1)ω
= 2πf = 2π × 50
= 100πR
= 52 Ω
Inductive reactance, XL = ωL
= 100πL
Therefore, Z = 52 + j100πL
The real part of the impedance represents the resistance R, while the imaginary part represents the inductive reactance XL. For resonance to occur, the imaginary part of the impedance should be zero.
Hence, 50πL = 102L
= 102 / 50π
Now, we can calculate the power consumed by the inductor, PL = I²XL Where I is the current through the inductor.
Therefore, the power factor of the circuit is 0.6585.
To know more about Resistance visit:
https://brainly.com/question/29427458
#SPJ11