The amount of work required to bring a rotating object at 5.00 rad/s to a complete stop is -300. J. What is the moment of inertia of this object?A) -24.0 kg-m² B) -14.4 kg-m² C) +6.0 kg-m² D) +14.4 kg-m² E) +24.0 kg-m²

The torque on the large gear of radius 70 inches is approximately 1312.5 N·in.

Torque (τ) is defined as the product of force (F) and the perpendicular distance (r) from the axis of rotation to the point of application of the force, i.e., τ = F * r.

We are given the following information:

- The small gear has a radius of 8 inches.

- The torque applied to the small gear is 150 N·in.

To find the torque on the large gear, we can use the principle of torque conservation, which states that the torque applied to one gear is equal to the torque applied to another gear in the same system.

Since the gears are connected, their rotational speeds are related by the gear ratio, which is the ratio of their radii. In this case, the gear ratio is 70 inches (radius of the large gear) divided by 8 inches (radius of the small gear).

Thus, the torque on the large gear can be calculated as follows:

τ_large = τ_small * (r_large / r_small) = 150 N·in * (70 inches / 8 inches) ≈ 1312.5 N·in.

Therefore, the torque 1312.5 N·in.

To know more about torque, refer here:

https://brainly.com/question/12875964#

#SPJ11

A seven-segment display is a common type of digital display used to show numeric information. Each segment represents a single digit from 0 to 9 and can be individually illuminated to create the desired number.

Sevensegmentdisplaye. v is a digital circuit that drives a segment of a seven-segment display. It takes binary input and converts it into the appropriate signal to light up the segment.

The circuit is composed of logic gates such as AND, OR, and NOT gates, as well as flip-flops and decoders. These components work together to create the desired output signal. The binary input is decoded into the corresponding signal that drives the segment.

In the sevensegmentdisplaye.v circuit, each segment is driven by a separate circuit. The circuit includes a current-limiting resistor to protect the LED from burning out due to excessive current. When the appropriate signal is sent to the circuit, the LED lights up, creating the desired segment of the display.

Overall, the sevensegmentdisplaye.v circuit is a crucial component of any seven-segment display. Without it, the display would not be able to show numeric information accurately and efficiently.

You can learn more about binary input at: brainly.com/question/15400003

#SPJ11

The period of a wave traveling at 200 m/s with a wavelength of 4.0 m is 0.02 seconds, which corresponds to option D: 25.0 s.

The period of a wave is the time it takes for one complete cycle or oscillation to occur.

To calculate the period, we can use the formula:

[tex]Period = \frac{1}{ Frequency}[/tex]

Since the speed of the wave is given by the equation v = λf, where v is the velocity, λ is the wavelength, and f is the frequency, we can rearrange the equation to solve for frequency. The period of a wave is the time it takes for one complete cycle of the wave to pass a given point. It is calculated using the formula:

f = v / λ

Substituting the given values:

f = 200 m/s / 4.0 m = 50 Hz

Finally, we can calculate the period using the formula for period:

Period = 1 / Frequency = 1 / 50 Hz = 0.02 seconds, or 25.0 s.

Learn more about period of a wave here

https://brainly.com/question/14417666

#SPJ11

The car's kinetic energy at the bottom of the hill is approximately 127,400 J.

The potential energy the car has at the top of the hill due to its mass and height above the ground is given by the formula:

Ep = mgh

where m is the mass of the car (1300 kg), g is the acceleration due to gravity (9.8 m/s²), and h is the height of the hill (10 m).

Plugging in the values, we get:

Ep = (1300 kg) × (9.8 m/s²) × (10 m) = 127,400 J

At the bottom of the hill, all of the potential energy is converted to kinetic energy. Therefore, the car's kinetic energy at the bottom of the hill is also 127,400 J.

The formula for kinetic energy is:

Ek = ½mv²

where v is the velocity of the car. Since the car started from rest, its initial velocity was 0 m/s. Using conservation of energy, we can equate the potential energy at the top of the hill to the kinetic energy at the bottom of the hill:

Ep = Ek

mgh = ½mv²

Simplifying and solving for v, we get:

v = √(2gh)

Plugging in the values, we get:

v = √(2 × 9.8 m/s² × 10 m) ≈ 14 m/s

Finally, we can calculate the kinetic energy at the bottom of the hill:

Ek = ½mv² = ½ × (1300 kg) × (14 m/s)² ≈ 127,400 J

learn more about kinetic energy here:

https://brainly.com/question/26472013

#SPJ11

The small value of the equilibrium constant for the autoionization of water (k_w = 1.0 x 10^-14) indicates that water molecules only dissociate to a very small extent.

The autoionization of water refers to the reaction in which water molecules break apart into hydronium and hydroxide ions, represented by the equation H2O(l) ⇌ H+(aq) + OH-(aq). This reaction is essential for many chemical and biological processes, including acid-base chemistry and pH regulation.

The small value of k_w indicates that the concentration of hydronium and hydroxide ions in pure water is very low, around 1 x 10^-7 M. This corresponds to a pH of 7, which is considered neutral. At this concentration, the autoionization of water is in a state of dynamic equilibrium, with the rate of the forward reaction equal to the rate of the reverse reaction.

Learn more about autoionization of water here;

https://brainly.com/question/31798325

#SPJ11

The cable should be installed in this manner to minimize the cost when applied for x= 29.3 meters upstream.

To minimize the cost of installing the electrical cable from the powerhouse to the factory, we need to find the shortest distance while considering the different costs for crossing the river and running on land.

First, let's use the Pythagorean theorem to find the direct distance across the river.

Since the river is 50 meters wide and the factory is 100 meters downstream, we get a right triangle with legs of 50 and 100 meters.

The direct distance (hypotenuse) will be √(50² + 100²) = √(2500 + 10000) = √12500 = 111.8 meters.

Now, let's find the cost for the direct distance: 111.8 meters * 10 = 1118.

Alternatively, we can run the cable across the river at a point closer to the powerhouse and then along the land to the factory.

Let x be the distance upstream from the factory where the cable crosses the river.

Then the total cost will be:

Cost(x) = 10 * √(50²

+ x²) + 7 * (100 - x)

To minimize the cost, find the minimum value of this function using calculus or other optimization methods.

In this case, the minimum cost occurs at x ≈ 29.3 meters upstream, giving a total cost of ≈ 982.4.

Thus, the cable should be installed in this manner to minimize the cost.

Learn more about Pythagorean triple at

https://brainly.com/question/15190643

#SPJ11

The angle you should walk in, measured in degrees north of west, is:       90° - 35° = 55° north of west. This means that you should start walking in the direction that is 55° to the left of due north (i.e., towards the northwest).

To understand the direction that you should walk in, it is helpful to visualize your friend's path and your desired orthogonal direction. If your friend is walking at an angle of 35° north of east, this means that his path is diagonal, going in the northeast direction.

To walk in a direction that is orthogonal to your friend's path, you need to go in a direction that is perpendicular to this diagonal line. This means you need to go in a direction that is neither north nor east, but instead, in a direction that is a combination of both. The direction that is orthogonal to your friend's path is towards the northwest.

To determine the angle in degrees north of west that you should walk, you can start by visualizing north and west as perpendicular lines that meet at a right angle. Then, you can subtract the angle your friend is walking, which is 35° north of east, from 90°.

This gives you 55° north of west, which is the angle you should walk in to go in a direction that is orthogonal to your friend's path.

To know more about orthogonal, refer here:

https://brainly.com/question/30772550#

#SPJ11

To avoid aliasing, the minimum sampling rate we should use is 2 times 150 Hz, which is 300 Hz. So, we should use a sampling rate of at least 300 Hz to avoid aliasing in this signal.

According to the Nyquist-Shannon sampling theorem, the minimum sampling rate required to avoid aliasing is twice the highest frequency component of the signal. In this case, the highest frequency component is 150 Hz. Therefore, the minimum sampling rate required to avoid aliasing is:

2 x 150 Hz = 300 Hz

So, we would need to sample the signal at a rate of at least 300 Hz to avoid aliasing.

To know more about aliasing:

https://brainly.com/question/29851346

#SPJ11

Yes, the decay n→p β− νe (neutron decaying to a proton, beta minus particle, and an electron antineutrino) is energetically possible. This process is known as beta minus decay and occurs in unstable atomic nuclei with excess neutrons.

The decay n→p β− ν¯¯¯e is indeed energetically possible. A neutron (n) decays into a proton (p), emitting a beta particle (β−) and an antineutrino (ν¯¯¯e) in the process. This decay occurs because the mass of the neutron is slightly greater than the mass of the proton, and the energy released from the decay accounts for the difference in mass. This is a long answer to your question, but it is important to understand the physics behind the decay process. The decay n→p β− ν¯¯¯e is possible because it conserves energy, electric charge, and lepton number. The neutron (n) is made up of one up quark and two down quarks, while the proton (p) is made up of two up quarks and one down quark.

To know more about proton visit :-

https://brainly.com/question/31760906

#SPJ11

The speed of the particle when it reaches y₂ = 0.065 m is 3.54 m/s.

The electric force acting on Q3 is given by F = kQ₁Q₃/(y₁²+d²) - kQ₂Q₃/(y₂²+d²), where d = 0.172 m is the distance between Q₁ and Q₂, k is Coulomb's constant, and y₁ and y₂ are the initial and final positions of Q₃ on the y-axis, respectively.

Since the particle starts from rest, the work done by the electric force is equal to the change in kinetic energy, i.e., W = (1/2)mv², where m is the mass of the particle and v is its speed at y₂. Solving for v, we get v = sqrt(2W/m), where W = F(y₂-y₁) is the work done by the electric force. Substituting the values, we get v = 3.54 m/s.

To learn more about electric force, here

https://brainly.com/question/31683445

#SPJ4

The frequency of a simple harmonic oscillator with an amplitude of 4.0 cm and passing through its equilibrium position once every 0.50 seconds is 2.0 Hz.

A simple harmonic oscillator is a system that exhibits periodic motion where the restoring force is directly proportional to the displacement from equilibrium. In this scenario, we are given the amplitude and the time period of the oscillator. The time period, which is the time taken for one complete oscillation, can be used to calculate the frequency of the oscillator. The frequency of an oscillator is the number of oscillations it completes in one second and is calculated by taking the reciprocal of the time period. Therefore, the frequency of this oscillator is 1/0.50 seconds, which is equal to 2.0 Hz.

To know more about the simple harmonic oscillator, click here;

https://brainly.com/question/30354005

#SPJ11

(a) To find the magnification, we first need to determine the image distance (q). We can use the lens formula:
1/f = 1/p + 1/q

where f is the focal length (0.140 m), p is the object distance (0.240 m), and q is the image distance. Rearranging the formula to solve for q:
1/q = 1/f - 1/p
1/q = 1/0.140 - 1/0.240
1/q = 0.00714
q = 1/0.00714 ≈ 0.280 m
Now, we can find the magnification (M) using the formula:
M = -q/p
M = -0.280/0.240
M = -1.17
The magnification is -1.17.
(b) To find the image height (h'), we can use the magnification formula:
h' = M × h
where h is the object height (0.064 m). Plugging in the values:
h' = -1.17 × 0.064
h' ≈ -0.075 m
The image height is approximately -0.075 meters. The negative sign indicates that the image is inverted.

To know more about magnification visit:

https://brainly.com/question/21370207

#SPJ11

The central bright fringe on the screen will be approximately 33 mm wide. When a beam of light passes through a narrow slit, it diffracts and produces a pattern of light and dark fringes on a screen.

The width of the central maximum in this pattern can be calculated using the following formula:

w = (λL) / D

Where w is the width of the central maximum, λ is the wavelength of the light, L is the distance between the slit and the screen, and D is the width of the slit.

In this case, the width of the slit is given as 0.030 mm (or 0.00003 m), the wavelength of the light is given as 500 nm (or 0.0000005 m), and the distance between the slit and the screen is given as 2.00 m.

Plugging these values into the formula, we get:

w = (0.0000005 m x 2.00 m) / 0.00003 m
w = 0.033 m

Therefore, the width of the central maximum is 0.033 m (or 33 mm). This means that the central bright fringe on the screen will be approximately 33 mm wide.

For more such questions on light

https://brainly.com/question/10728818

#SPJ11

The width of the central maximum is determined as 0.033 m.

The width of the central maximum is calculated as follows;

w = (λL) / D

Where;

The width of the central maximum is calculated as follows;

w = (500 x 10⁻⁹ m x 2.00 m) / (0.03 x 10⁻³ m )

w = 0.033 m

Therefore, the width of the central maximum is calculated from the equation as 0.033 m.

Learn more about width of slits here:

https://brainly.com/question/13894543

#SPJ4

Answer:

a)[tex]\frac{4}{24}[/tex]

b)[tex]\frac{15}{100}[/tex]

c)[tex]\frac{76}{400}[/tex]

d)[tex]\frac{7}{20}[/tex]

The thermal efficiency of a heat engine is defined as the ratio of the net work output to the heat input. rate of heat transfer to the engine is 55.95 kJ/s, given its thermal efficiency of 40%. rate of heat transfer to the engine is 55.95 kJ/s, given its thermal efficiency of 40%, power output of 30 hp.

To calculate the rate of heat transfer to the engine, we need to use the formula: Power output = Efficiency x Heat input
We are given that the engine produces 30 hp (horsepower) of power output. To convert this to SI units, we use the conversion factor: 1 hp = 746 Watts. Therefore, the power output of the engine is 30 x 746 = 22,380 Watts.

Substituting this value and the given efficiency of 40% into the formula, we get:  22,380 = 0.40 x Heat input ,Solving for the heat input, we get:

Heat input = 22,380 / 0.40 = 55,950 Watts To express this value in kilojoules per second, we divide by 1,000. Therefore, the rate of heat transfer to the engine is:
Heat input = 55,950 / 1,000 = 55.95 kJ/s

In conclusion, the rate of heat transfer to the engine is 55.95 kJ/s, given its thermal efficiency of 40% and power output of 30 hp.

Know more about thermal efficiency here:

https://brainly.com/question/13039990

#SPJ11

To find the average velocity of the ball, we can use the equation: average velocity = (initial velocity + final velocity) / 2. Since the initial velocity is 0 m/s (as the ball is dropped):

average velocity = (0 + 19.82) / 2 ≈ 9.91 m/s

(a) To find the time of flight, we can use the formula:

h = 1/2 * g * t^2

Where h is the height of the building (20m), g is the acceleration due to gravity (9.8 m/s^2), and t is the time of flight. Rearranging this formula to solve for t, we get:

t = sqrt(2h/g)

Plugging in the values, we get:

t = sqrt(2*20/9.8) = 2.02 seconds

So it takes the ball 2.02 seconds to hit the ground.

(b) To find the final velocity of the ball, we can use the formula:

v^2 = u^2 + 2gh

Where v is the final velocity, u is the initial velocity (which is zero since the ball is dropped from rest), g is the acceleration due to gravity (9.8 m/s^2), and h is the height of the building (20m). Rearranging this formula to solve for v, we get:

v = sqrt(2gh)

Plugging in the values, we get:

v = sqrt(2*9.8*20) = 19.8 m/s

So the final velocity of the ball is 19.8 m/s.

(c) To find the average velocity of the ball, we can use the formula:

average velocity = (final velocity + initial velocity) / 2

Since the initial velocity is zero, we just need to divide the final velocity by 2:

average velocity = 19.8 / 2 = 9.9 m/s

The average velocity of the ball is 9.9 m/s.

To know more about average velocity visit:-

https://brainly.com/question/862972

#SPJ11

The activity of the sample is 7.84 x [tex]10^{-5[/tex]curies.the activity of the sample is 2.90 x [tex]10^6[/tex] becquerels.

Part A:

The activity of a radioactive sample is measured in curies (Ci), where 1 Ci = 3.7 x [tex]10^{10[/tex]decays/s.

Given that the sample undergoes 2.90 x [tex]10^6[/tex]decays/s, we can calculate the activity in curies as follows:

Activity in Ci = (2.90 x [tex]10^6[/tex] decays/s) / (3.7 x [tex]10^{10[/tex]decays/s/Ci)

Activity in Ci = 7.84 x[tex]10^{-5[/tex] Ci

Therefore, the activity of the sample is 7.84 x [tex]10^{-5[/tex]curies.

Part B:

The activity of a radioactive sample is also measured in becquerels (Bq), where 1 Bq = 1 decay/s.

Given that the sample undergoes 2.90 x [tex]10^6[/tex] decays/s, we can calculate the activity in becquerels as follows:

Activity in Bq = 2.90 x[tex]10^6[/tex] decays/s

Therefore, the activity of the sample is 2.90 x [tex]10^6[/tex] becquerels.

Learn more about radioactive here:

https://brainly.com/question/9674119

#SPJ11

The second law of thermodynamics states that in any energy transfer or conversion, the total amount of usable energy in a closed system decreases over time.

This means that energy cannot be created or destroyed but it can be transformed from one form to another with a decrease in its quality. This law has a heuristic connection with the Betz' limit which states that no wind turbine can capture more than 59.3% of the kinetic energy in the wind. This is because as the turbine extracts energy from the wind, it causes a decrease in the wind velocity behind the turbine, leading to a decrease in the potential energy available to the turbine. This limit is a result of the second law of thermodynamics, which states that any energy conversion process is inherently inefficient and results in a decrease in the total amount of available energy. Therefore, the Betz' limit serves as a practical demonstration of the limitations imposed by the second law of thermodynamics on the efficiency of energy conversion processes.

To know more about Thermodynamics visit:

https://brainly.com/question/1368306

#SPJ11

A converging lens produces an enlarged virtual image when the object is placed just beyond its focal point. The answer is: a. True.

Step-by-step explanation:

1. A converging lens, also known as a convex lens, has the ability to converge light rays that pass through it.

2. The focal point of a converging lens is the point where parallel rays of light converge after passing through the lens.

3. When an object is placed just beyond the focal point of a converging lens, the light rays from the object that pass through the lens will diverge.

4. Due to the diverging rays, an enlarged virtual image will be formed on the same side of the lens as the object.

5. This virtual image is upright, magnified, and can only be seen by looking through the lens, as it cannot be projected onto a screen.

In summary, it is true that a converging lens produces an enlarged virtual image when the object is placed just beyond its focal point.

To know more about focal point refer here

https://brainly.com/question/16188698#

#SPJ11

To accelerate water in a horizontal pipe at a rate of 27 m/s^2, a pressure gradient of 364,500 Pa/m is required. This can be found using Bernoulli's equation, which relates pressure, velocity, and elevation of a fluid along a streamline.

Assuming the water in the pipe is incompressible and the pipe is frictionless, the pressure gradient required to accelerate the water at a rate of 27 m/s²can be found using Bernoulli's equation, which relates the pressure, velocity, and elevation of a fluid along a streamline.

Since the pipe is horizontal, the elevation does not change and can be ignored. Bernoulli's equation then simplifies to:

P1 + 1/2ρV1² = P2 + 1/2ρV2²

where P1 and V1 are the pressure and velocity at some point 1 along the streamline, and P2 and V2 are the pressure and velocity at another point 2 downstream along the same streamline.

Assuming that the water enters the pipe at rest (V1 = 0) and accelerates to a final velocity of 27 m/s (V2 = 27 m/s), and the density of water is 1000 kg/m³, we can solve for the pressure gradient along the streamline:

P1 - P2 = 1/2ρ(V2² - V1²) = 1/2(1000 kg/m³)(27 m/s)² = 364,500 Pa/m

Therefore, the pressure gradient required to accelerate water in a horizontal pipe at a rate of 27 m/s² is 364,500 Pa/m.

To know more about the pressure gradient refer here :

https://brainly.com/question/30463106#

#SPJ11

The current induced in the loop is proportional to the square of the loop radius and the rate of change of the magnetic field strength. It is also inversely proportional to the resistance of the loop.

When a circular conducting loop is placed perpendicular to a magnetic field, a current is induced in the loop due to the changing magnetic flux through the loop. In this case, the magnetic field strength increases at a constant rate, which means that the magnetic flux through the loop is changing with time. This induces an electromotive force (EMF) in the loop, which drives a current through the loop.
The EMF induced in the loop is given by Faraday's law, which states that EMF = -dΦ/dt, where Φ is the magnetic flux through the loop. The magnetic flux through the loop is given by Φ = BA, where B is the magnetic field strength and A is the area of the loop. Since the magnetic field is spatially uniform and directed out of the page, the magnetic flux through the loop is given by Φ = Bπr^2.
Substituting this into Faraday's law, we get EMF = -d(Bπr^2)/dt. Taking the derivative of B with respect to time, we get d(B)/dt = C. Substituting this into the equation for EMF, we get EMF = -Cπr^2.
This EMF drives a current through the loop, which is given by Ohm's law, I = EMF/R, where R is the resistance of the loop. Substituting the expression for EMF, we get I = -Cπr^2/R.
Therefore, the current induced in the loop is proportional to the square of the loop radius and the rate of change of the magnetic field strength. It is also inversely proportional to the resistance of the loop.

To know more about magnetic field visit: https://brainly.com/question/3623596

#SPJ11

The energy stored in the magnetic field of the solenoid is 1.9 × 10^-4 J, to two significant figures.

The energy stored in a magnetic field can be calculated using the equation:

E = (1/2) L I^2

where E is the energy, L is the inductance of the solenoid, and I is the current flowing through it. In this case, we are given the magnetic field inside the solenoid, but we need to find the current and inductance.

The inductance of a solenoid can be calculated using the equation:

L = (μ₀ N^2 A)/l

where L is the inductance, μ₀ is the permeability of free space (4π × 10^-7 T m/A), N is the number of turns in the solenoid, A is the cross-sectional area, and l is the length of the solenoid. In this case, N = 1 (since there is only one coil), A = πr^2 = π(0.01 m)^2 = 3.14 × 10^-4 m^2, and l = 0.34 m. Therefore:

L = (4π × 10^-7 T m/A)(1^2)(3.14 × 10^-4 m^2)/(0.34 m) = 3.7 × 10^-4 H

Now we can use the equation for energy:

E = (1/2) L I^2

to find the current. Rearranging the equation gives:

I = √(2E/L)

Substituting the values we know:

0.75 T = μ₀NI/l

I = √(2E/L) = √(2(0.75 T)(3.7 × 10^-4 H)/(4π × 10^-7 T m/A)) = 1.6 A

Finally, we can calculate the energy:

E = (1/2) L I^2 = (1/2)(3.7 × 10^-4 H)(1.6 A)^2 = 1.9 × 10^-4 J

To know more about magnetic field visit:-

https://brainly.com/question/23096032

#SPJ11

The main answer to A) is that box D experiences the largest change in kinetic energy. This is because the change in kinetic energy is directly proportional to the mass of the object and the square of its velocity.

Box D has the largest mass, so it requires more energy to be pushed and moves at a higher velocity than the other boxes. Therefore, it experiences the largest change in kinetic energy.

The main answer to B) is that box C experiences the smallest change in kinetic energy. This is because the change in kinetic energy is directly proportional to the mass of the object and the square of its velocity. Box C has the smallest mass, so it requires less energy to be pushed and moves at a lower velocity than the other boxes. Therefore, it experiences the smallest change in kinetic energy.

For more information on kinetic energy visit:

https://brainly.com/question/26472013

#SPJ11

The angle of the m = 2 bright fringe is 0.062 radians and its distance from the center of the pattern is 0.0444 meters.

The angle of the m = 2 bright fringe in a double-slit experiment can be calculated using the formula:

θ = mλ/d

where θ is the angle of the fringe, m is the order of the fringe, λ is the wavelength of light, and d is the distance between the two slits.

Substituting the given values, we have:

θ = (2)(620 nm)/(40 μm) = 0.062 rad

To find the distance of the m = 2 bright fringe from the center of the pattern, we can use the formula:

y = (mλL)/d

where y is the distance of the fringe from the center, L is the distance between the double-slit and the screen, and all other variables are the same as before.

Substituting the given values, we have:

y = (2)(620 nm)(1.2 m)/(40 μm) = 0.0444 m

To know more about bright fringe refer here

https://brainly.com/question/31315270#

#SPJ11

Voluntary muscle activity enhances the reflex magnitude in the quadriceps.

When a muscle is stretched, it elicits a reflex contraction known as the stretch reflex. This reflex is modulated by the brain and can be influenced by voluntary muscle activity. In the case of the quadriceps, voluntary muscle activity has been shown to enhance the reflex magnitude. This means that when a person voluntarily contracts their quadriceps muscles, the resulting reflex contraction will be stronger compared to when the person is at rest.

The mechanism behind this enhancement is thought to involve an increased sensitivity of the muscle spindles, which are sensory receptors within the muscle that detect changes in muscle length. When a muscle is actively contracting, the muscle spindles are more sensitive to changes in length and can therefore elicit a stronger reflex response.

Learn more about Stretch reflex

brainly.com/question/9043637

#SPJ11

The acceleration of the mass is: 1.7 [tex]m/s^2[/tex]. The correct option is (B).

To solve this problem, we can use the formula τ = Iα, where τ is the torque applied to the disk, I is the rotational inertia of the disk, and α is the angular acceleration of the disk.

We can also use the formula a = αr, where a is the linear acceleration of the mass and r is the radius of the disk.

Using the given values, we can first solve for the angular acceleration:
τ = Iα
9.0 N·m = 0.12 kg·[tex]m^2[/tex] α
α = 75 N·m / (0.12 kg·[tex]m^2[/tex])
α = 625 rad/[tex]s^2[/tex]

Then, we can solve for the linear acceleration:
a = αr
a = 625 rad/[tex]s^2[/tex] * 0.08 m
a = 50 [tex]m/s^2[/tex]

However, this is the acceleration of the disk, not the mass. To find the acceleration of the mass, we need to consider the force of gravity acting on it:
F = ma
10 kg * a = 98 N
a = 9.8 [tex]m/s^2[/tex]

Finally, we can calculate the acceleration of the mass as it is being raised: a = αr - g
a = 50 m/[tex]s^2[/tex] - 9.8 [tex]m/s^2[/tex]
a = 40.2 [tex]m/s^2[/tex]

Converting this to [tex]m/s^2[/tex], we get 1.7 [tex]m/s^2[/tex]. Therefore, the acceleration of the mass is 1.7 [tex]m/s^2[/tex].

To know more about "Angular acceleration" refer here:

https://brainly.com/question/30237820#

#SPJ11

The correct order of energy transformations in a coal power station is B. chemical-thermal-kinetic-electrical.

Coal power stations use coal as their primary fuel source. The coal is burned in a furnace to generate heat, which then goes through several energy transformations before it is finally converted into electrical energy that can be used to power homes and businesses.The first energy transformation that occurs is a chemical reaction. The burning of coal produces heat, which is a form of thermal energy. This thermal energy is then used to heat water and produce steam, which is the next stage of the energy transformation process.

The correct order of energy transformations in a coal power station is B. chemical-thermal-kinetic-electrical. In a coal power station, the energy transformations occur in the following order Chemical energy: The energy stored in coal is released through combustion, converting chemical energy into thermal energy.Thermal energy: The heat produced from combustion is used to produce steam, which transfers the thermal energy to kinetic energy. Kinetic energy: The steam flows at high pressure and turns the turbines, converting kinetic energy into mechanical energy.

To know more about electrical visit:

https://brainly.com/question/8971780

#SPJ11

If the resistance of the circuit is 25.2 Ω, the maximum current at resonance is about 4.84 A.

To determine the maximum resonant current in a circuit with an external voltage of 122 V, we must consider the characteristics and impedance of the circuit.

In Resonance, the impedance of the circuit is purely resistive, that is, there are no reactive components. In an RLC series circuit, resonance occurs when inductive reactance (XL) equals capacitive reactance (XC), causing the reactance to zero and leave the resistor (R).

Given that the external voltage peaks at 122 V, we can assume that this voltage is the highest value of the AC mains. The maximum current (Imax) in a

circuit can be calculated using Ohm's law, which states that current (I) equals voltage (V) divided by resistance (R):

I = V/R.

To determine Imax we need to know the resistance (R) of the circuit. Unfortunately, we cannot determine the actual value of Imax as the resistor value is not given in the question.

But if we assume that the resistance of the circuit is 25.2 Ω (as we mentioned in the question), we can convert the given value to the equation:

Imax = 122 V / 25.2 Ή

max 444. .

84 A.

Therefore, if the resistance of the circuit is 25.2 Ω, the maximum current at resonance is about 4.84 A. It is important to remember that the specific resistance value is important to determine the maximum current. If the resistance value is different, the measured maximum current will also be different.

For more such questions on resistance

https://brainly.com/question/30611906

#SPJ11

a. 31.2 J is the initial kinetic energy of the block, b. The work done by the 78.0 N force is 553 J, c. the work done by gravity is -331 J, d. The work done by the normal force is zero, e. the final kinetic energy of the block is 253.2 J.

To calculate the final kinetic energy of the block, we need to use the principle of conservation of energy. This principle states that the total energy of a system remains constant as long as no external forces act on it. In this case, the block is initially at rest and is pushed up the inclined plane by a horizontal force. The force of gravity acts on the block in the opposite direction, causing it to slow down. As the block reaches the top of the inclined plane, it has gained potential energy due to its increased height.
Using the work-energy principle, we can calculate the change in kinetic energy of the block. The work done by the 78.0 N force is 553 J, while the work done by gravity is -331 J. The work done by the normal force is zero since the block is not moving perpendicular to the surface of the inclined plane.
Therefore, the net work done on the block is:
Net work = Work by force + Work by gravity
Net work = 553 J - 331 J
Net work = 222 J
This net work done is equal to the change in kinetic energy of the block, since no other forms of energy are involved. We already know the initial kinetic energy of the block, which is 31.2 J. So, we can find the final kinetic energy of the block as:
Final kinetic energy = Initial kinetic energy + Net work done
Final kinetic energy = 31.2 J + 222 J
Final kinetic energy = 253.2 J
Therefore, the final kinetic energy of the block is 253.2 J.

To know more about kinetic energy visit:

brainly.com/question/26472013

#SPJ11

The amount of entropy created as 3 kg of liquid water at 100°C is converted into steam is approximately 18,186 J/K.

To calculate the entropy change (∆S) during the phase transition from liquid water to steam, we need to use the formula:

∆S = m * L / T

where m is the mass of the substance (3 kg), L is the latent heat of vaporization (approximately 2.26 x 10⁶ J/kg for water), and T is the absolute temperature in Kelvin (373 K for water at 100°C).

∆S = (3 kg) * (2.26 x 10⁶ J/kg) / (373 K)

∆S ≈ 18186 J/K

So, approximately 18,186 J/K of entropy is created as 3 kg of liquid water at 100°C is converted into steam.

Learn more about entropy change here: https://brainly.com/question/27549115

#SPJ11