Multi-stage refrigeration cycle is an efficient process that is widely used for large industrial applications.
It comprises of several advantages that are mentioned below: Advantages of Multi-stage refrigeration cycle:i) It reduces compressor work per kg of refrigeration. ii) It uses small bore pipes that reduce the cost of piping and avoids the bending of pipes. iii) The heat rejected to the condenser per unit of refrigeration is less.
Hence, the condenser size is also less. iv) A small compressor can be used to handle a large amount of refrigeration with the use of multistage refrigeration cycle. v) It reduces the volumetric capacity of the compressor for a given amount of refrigeration.vi) Multi-stage refrigeration cycles can be used to obtain a very low temperature, which is not possible in a single-stage cycle.
To know more about refrigeration visit:-
https://brainly.com/question/12950674
#SPJ11
A turbine enters steam at 4000 kPa, 500 °C, 200 m/s and an outlet corresponding to saturated steam at 175 kPa and a speed of 120 m/s. If the mass flow is 2000 kg/min, and the power output is 15000 kW. Determine (a) the magnitude of the heat transferred. (b) Draw this process on the P-v diagram. (place the saturation lines)
A turbine enters steam at 4000 kPa, 500°C, 200 m/s and an outlet corresponding to saturated steam at 175 kPa and a speed of 120 m/s. If the mass flow is 2000 kg/min, and the power output is 15000 kW, we can determine
The magnitude of the heat transferred In order to calculate the magnitude of the heat transferred, we need to find the difference in enthalpy at the inlet and outlet of the turbine using the formula: Q = (m × (h2 - h1))WhereQ is the magnitude of heat transferred m is the mass flowh1 is the enthalpy of steam at the turbine inleth2 is the enthalpy of steam at the turbine outlet
We can calculate the enthalpy values using steam tables at the given pressures and temperatures. We get:
[tex]h1 = 3485.7 kJ/kgh2 = 2534.2 kJ/kg[/tex]Now, we can substitute the values to find the magnitude of heat transferred:
[tex]Q = (2000 kg/min × (2534.2 - 3485.7) kJ/kg/min) = -1.903 × 10^7 kJ/min[/tex]
Therefore, the magnitude of heat transferred is -1.903 × 10^7 kJ/min.
Initially, the steam enters the turbine at state 1 and undergoes an adiabatic (isentropic) expansion to state 2, corresponding to saturated steam at 175 kPa. This process is represented by the blue line on the diagram. The area under the curve represents the work output of the turbine, which is equal to 15000 kW in this case.
The saturation lines are represented by the red lines.
To know more about adiabatic visit:-
https://brainly.com/question/13002309
#SPJ11
1- Write about daily, monthly, and yearly loads.
2- Why generated power at electrical stations must equal load power (consumed power).
3- What is " based load", "intermediate load" and "peak load", draw.
4- Why electrical station are built far from cities?
5- On which principles the location of electrical stations is selected.
6- Why mainly A/C synchronous generators are used to generate electrical energy.
7- Why we use high voltage for transmission lines.
8- Compare between A/C and DC transmission lines.
9- What do we mean by "synchronized system"?
10- What is the role of the "preheater" in electrical stations?
11- Why we use low, medium and high-pressure turbines in electrical stations.
12- Discuss electrical stations efficiencies. and losses in electrical stations.
Daily, monthly, as well as yearly loads connote to the extent of electrical power that is taken in by a system or a region over different time frame.
What is load",Daily load means how much electricity is being used at different times of the day, over a 24-hour period. Usually, people use more electricity in the morning and evening when they use appliances and lights.
Monthly load means the total amount of electricity used in a month. This considers changes in how much energy is used each day and includes things like weather, seasons, and how people typically use energy.
Yearly load means the amount of energy used in a whole year. This looks at how much energy people use each month and helps companies plan how much energy they need to make and deliver over a long time.
Read more about based load here:
https://brainly.com/question/1288780
#SPJ4
A thin-walled spherical vessel, of internal diameter 10 m and wall thickness 2 cm, is filled with water. Determine the additional water that is required to be pumped into the vessel to raise its internal pressure by 0.5 MPa. Let: E = 200 GPa; K = 2 GPa; v = 0.3. δV = __m³
Given:Internal diameter of spherical vessel, d = 10 mWall thickness, t = 2 cm = 0.02 mInternal pressure, Δp = 0.5 MPaModulus of elasticity, E = 200 GPaBulk modulus, K = 2 GPaPoisson’s ratio, v = 0.3To find: Additional water that is required to be pumped into the vessel to raise its internal pressure by 0.5 MPaChange in volume, δV = .
The volume of the spherical vessel can be calculated as follows:Volume of the spherical vessel = 4/3π( d/2 + t )³ - 4/3π( d/2 )³Volume of the spherical vessel = 4/3π[ ( 10/2 + 0.02 )³ - ( 10/2 )³ ]Volume of the spherical vessel = 4/3π[ ( 5.01 )³ - ( 5 )³ ]Volume of the spherical vessel = 523.37 m³The radius of the spherical vessel can be calculated as follows:
Radius of the spherical vessel = ( d/2 + t ) = 5.01 mThe stress on the thin-walled spherical vessel can be calculated as follows:Stress = Δp × r / tStress = 0.5 × 5.01 / 0.02Stress = 125.25 MPa.
To know more about diameter visit:
https://brainly.com/question/32968193
#SPJ11
A rubber ball (see figure) is inflated to a pressure of 66kPa. (a) Determine the maximum stress (in MPa) and strain in the ball. (Use the deformation sign convention.) σmax=yPaεmax= (b) If the strain must be limited to 0.417, find the minimum required wall thickness of the ball (in mm). mm
The maximum stress σmax and strain εmax in a rubber ball can be calculated as follows:Maximum Stress σmax= yPaMaximum Strain εmax= P/ywhere y is the Young's modulus of rubber and P is the gauge pressure of the ball.
Here, y is given to be 5.0 × 10^8 Pa and P is given to be 66 kPa (= 66,000 Pa).Therefore,Maximum Stress σmax
= (5.0 × 10^8 Pa) × (66,000 Pa)
= 3.3 × 10^11 Pa
= 330 MPaMaximum Strain εmax
= (66,000 Pa) / (5.0 × 10^8 Pa)
= 0.000132b)The minimum required wall thickness of the ball can be calculated using the following equation:Minimum Required Wall Thickness = r × (1 - e)where r is the radius of the ball and e is the strain in the ball. Here, the strain is given to be 0.417 and the radius can be calculated from the volume of the ball.Volume of the Ball = (4/3)πr³where r is the radius of the ball. Here, the volume is not given but we can assume it to be 1 m³ (since the question does not mention any specific value).
Therefore,1 m³ = (4/3)πr³r³
= (1 m³) / [(4/3)π]r
= 0.6204 m (approx.)Therefore,Minimum Required Wall Thickness
= (0.6204 m) × (1 - 0.417)
= 0.3646 m
= 364.6 mm (approx.)Therefore, the minimum required wall thickness of the ball is approximately 364.6 mm.
To know more about ball visit:
https://brainly.com/question/10151241
#SPJ11
Use the transformation defined by T(v): 12: V3) = (v2 - V1: ,+ v2: 2v1) to find the image of v= (1.4.0) a.(-3, 5, 2) . b.(-3,5,8) O c. (5,3, 2) O d. (3, 5, 2) O e.(3,5,8)
Based on the calculations, the correct answer is d) (3, 5, 2) .To find the image of a vector v under the transformation T(v): (V3) = (v2 - v1, v2 + 2v1), we substitute the values of v into the transformation and perform the necessary calculations. Let's calculate the images for each given vector:
a) v = (-3, 5, 2)
T(-3, 5, 2) = (5 - (-3), 5 + 2(-3), 2(5)) = (8, -1, 10)
b) v = (-3, 5, 8)
T(-3, 5, 8) = (5 - (-3), 5 + 2(-3), 2(5)) = (8, -1, 10)
c) v = (5, 3, 2)
T(5, 3, 2) = (3 - 5, 3 + 2(5), 2(3)) = (-2, 13, 6)
d) v = (3, 5, 2)
T(3, 5, 2) = (5 - 3, 5 + 2(3), 2(5)) = (2, 11, 10)
e) v = (3, 5, 8)
T(3, 5, 8) = (5 - 3, 5 + 2(3), 2(5)) = (2, 11, 10)
Therefore, the images of the given vectors are:
a) (8, -1, 10)
b) (8, -1, 10)
c) (-2, 13, 6)
d) (2, 11, 10)
e) (2, 11, 10)
Based on the calculations, the correct answer is:
d) (3, 5, 2)
Learn more about vector here:
https://brainly.com/question/24256726
#SPJ11
The open-loop transfer function of a unit-negative-feedback system has the form of
G(s)H(s) = 1 / s(s+1).
Please determine the following transient specifications when the reference input is a unit step function:
(1) Percentage overshoot σ%;
(2) Peak time tp;
(3) 2% Settling time t.
For the given open-loop transfer function 1 / (s(s+1)), the transient specifications when the reference input is a unit step function can be determined by calculating the percentage overshoot, peak time, and 2% settling time using appropriate formulas for a second-order system.
What is the percentage overshoot?To determine the transient specifications for the given open-loop transfer function G(s)H(s) = 1 / (s(s+1)) with a unit step reference input, we need to analyze the corresponding closed-loop system.
1) Percentage overshoot (σ%):
The percentage overshoot is a measure of how much the response exceeds the final steady-state value. For a second-order system like this, the percentage overshoot can be approximated using the formula: σ% ≈ exp((-ζπ) / √(1-ζ^2)) * 100, where ζ is the damping ratio. In this case, ζ = 1 / (2√2), so substituting this value into the formula will give the percentage overshoot.
2) Peak time (tp):
The peak time is the time it takes for the response to reach its maximum value. For a second-order system, the peak time can be approximated using the formula: tp ≈ π / (ωd√(1-ζ^2)), where ωd is the undamped natural frequency. In this case, ωd = 1, so substituting this value into the formula will give the peak time.
3) 2% settling time (ts):
The settling time is the time it takes for the response to reach and stay within 2% of the final steady-state value. For a second-order system, the settling time can be approximated using the formula: ts ≈ 4 / (ζωn), where ωn is the natural frequency. In this case, ωn = 1, so substituting this value into the formula will give the 2% settling time.
Learn more on peak time here;
https://brainly.com/question/28195480
#SPJ4
A conical tube is fixed vertically with its smaller end upwards and it forms a part of pipeline. The velocity at the smaller end is 4.5 m/s and at the large end 1.5 m/s. Length of conical tube is 1.5 m. The pressure at the upper end is equivalent to a head of 10 m of water. (i) Neglecting friction, determine the pressure at the lower end of the tube.
Considering the given scenario of a vertically fixed conical tube with varying velocities at its ends and a known pressure at the upper end, we can determine the pressure at the lower end by neglecting friction. The calculated value for the pressure at the lower end is missing.
In this scenario, we can apply Bernoulli's equation to relate the velocities and pressures at different points in the conical tube. Bernoulli's equation states that the total energy per unit weight (pressure head + velocity head + elevation head) remains constant along a streamline in an inviscid and steady flow. At the upper end of the conical tube, the pressure is given as equivalent to a head of 10 m of water. Let's denote this pressure as P1. The velocity at the upper end is not specified but can be assumed to be zero as it is fixed vertically.
At the lower end of the conical tube, the velocity is given as 1.5 m/s. Let's denote this velocity as V2. We need to determine the pressure at this point, denoted as P2. Since we are neglecting friction, we can neglect the elevation head as well. Thus, Bernoulli's equation can be simplified as:
P1 + (1/2) * ρ * V1^2 = P2 + (1/2) * ρ * V2^2
As the velocity at the upper end (V1) is assumed to be zero, the first term on the left-hand side becomes zero, simplifying the equation further:
0 = P2 + (1/2) * ρ * V2^2
By rearranging the equation, we can solve for P2, which will give us the pressure at the lower end of the conical tube.
Learn more about friction here: https://brainly.com/question/4468721
#SPJ11
There is a gear transmission that has a distance between centers of 82.5 mm and a transmission ratio n=1.75, the gears that constitute it have a module of 3 mm. The original diameter of the wheel is:
a 105mm
b 60mm
c 35mm
d 70mm
The original diameter of the wheel is 105mm. The correct option is (a)
Given:
Distance between centers = 82.5 mm.
Transmission ratio, n = 1.75.Module, m = 3 mm.
Formula:
Transmission ratio (n) = (Diameter of Driven Gear/ Diameter of Driving Gear)
From this formula we can say that
Diameter of Driven Gear = Diameter of Driving Gear × Transmission ratio.
Diameter of Driving Gear = Distance between centers/ (m × π).Diameter of Driven Gear = Diameter of Driving Gear × n.
Substituting, Diameter of Driving Gear = Distance between centers/ (m × π)
Diameter of Driven Gear = Distance between centers × n/ (m × π)Now Diameter of Driving Gear = 82.5 mm/ (3 mm × 3.14) = 8.766 mm
Diameter of Driven Gear = Diameter of Driving Gear × n = 8.766 × 1.75 = 15.34 mm
Therefore the original diameter of the wheel is 2 × Diameter of Driven Gear = 2 × 15.34 mm = 30.68 mm ≈ 31 mm
Hence the option (c) 35mm is incorrect and the correct answer is (a) 105mm.
To learn more about Transmission ratio
https://brainly.com/question/13872614
#SPJ11
Fick's first law gives the expression of diffusion flux (l) for a steady concentration gradient (Δc/ Δx) as: J=-D Δc/ Δx
Comparing the diffusion problem with electrical transport analogue; explain why the heat treatment process in materials processing has to be at high temperatures.
Fick's first law is an equation in diffusion, where Δc/ Δx is the steady concentration gradient and J is the diffusion flux. The equation is J=-D Δc/ Δx. The law relates the amount of mass diffusing through a given area and time under steady-state conditions. Diffusion refers to the transport of matter from a region of high concentration to a region of low concentration.
The driving force for diffusion is the concentration gradient. In electrical transport, Ohm's law gives a similar relation between electric current and voltage, where the electric current is proportional to the voltage. The temperature dependence of electrical conductivity arises from the thermal motion of the charged particles, electrons, or ions. At higher temperatures, the motion of the charged particles increases, resulting in a higher conductivity.
Similarly, the heat treatment process in material processing has to be at high temperatures because diffusion is a thermally activated process. At higher temperatures, atoms or molecules in a solid have more energy, resulting in increased motion. The increased motion, in turn, increases the rate of diffusion. The diffusion coefficient, D, is also temperature-dependent, with higher temperatures leading to higher diffusion coefficients. Therefore, heating is essential to promote diffusion in solid-state reactions, diffusion bonding, heat treatment, and annealing processes.
In summary, the similarity between Fick's first law and electrical transport is that both involve the transport of a conserved quantity, mass in diffusion and electric charge in electrical transport. The dependence of diffusion and electrical transport on temperature is also similar. Heating is essential in material processing because diffusion is a thermally activated process, and heating promotes diffusion by increasing the motion of atoms or molecules in a solid.
For more such questions on Fick's first law, click on:
https://brainly.com/question/31958586
#SPJ8
A closed system initially contains 2 kg of air at 40°C and 2 bar. Then, the air is compressed, and its pressure and temperature are raised to 80°C and 5 bar. Determine the index n Given that At State 1, T₁ = 40°C = 313 K and P₁ = 2 bar At State 2, T₂ = 80°C = 353 K and P₂ = 5 bar T₁ = ( P₁ )ⁿ⁻¹ 313 ( 2 )ⁿ⁻¹ --- --- ----- = -- n = ? T₂ P₂ 353 5
Given,Initial state of the system, T1 = 40 °C
= 313 K and
P1 = 2 bar. Final state of the system,
T2 = 80 °C
= 353 K and
P2 = 5 bar.
T1 = P1(n-1) / (P2 / T2)n
= [ T1 * (P2 / P1) ] / [T2 + (n-1) * T1 * (P2 / P1) ]n
= [ 313 * (5 / 2) ] / [ 353 + (n-1) * 313 * (5 / 2)]n
= 2.1884approx n = 2.19 (approximately)
Therefore, the index n of the system is 2.19 (approx). Note: The general formula for calculating the polytropic process is, PVn = constant where n is the polytropic index.
If n = 0, the process is isobaric;
If n = ∞, the process is isochoric.
To know more about Initial visit:
https://brainly.com/question/32209767
#SPJ11
Design a singly reinforced beam (SRB) using WSD and given the following data: fc' = 25 MPa; fy = 276 MPa; fs = 138 MPa ; n = 12. Use 28 mm diameter main bars and 12 mm diameter stirrups. Solve only the following: 1. k, j, (don't round-off) and R (rounded to 3 decimal places) 2. Designing maximum moment due to applied loads.
3. Trial b.d, and t. (Round - off d value to next whole higher number that is divisible by 25.) 4. Weight of the beam (2 decimal places).
5. Maximum moment in addition to weight of the beam. 6. Number of 28 mm diameter main bars. 7. Check for shear 8. Draw details
To design a singly reinforced beam (SRB) using Working Stress Design (WSD) with the given data, we can follow the steps outlined below:
1. Determine k, j, and R:
k is the lever arm factor, given by k = 0.85.j is the depth factor, given by j = 0.90.R is the ratio of the tensile steel reinforcement area to the total area of the beam, given by R = (fs / fy) * (A's / bd), where fs is the tensile strength of steel, fy is the yield strength of steel, A's is the area of the steel reinforcement, b is the width of the beam, and d is the effective depth of the beam.2. Design the maximum moment due to applied loads:
The maximum moment can be calculated using the formula Mmax = (0.85 * fy * A's * (d - 0.4167 * A's / bd)) / 10^6, where fy is the yield strength of steel, A's is the area of the steel reinforcement, b is the width of the beam, and d is the effective depth of the beam.
3. Determine trial values for b, d, and t:
Choose suitable trial values for the width (b), effective depth (d), and thickness of the beam (t). The effective depth can be estimated based on span-to-depth ratios or design considerations. Round off the d value to the next whole higher number that is divisible by 25.
4. Calculate the weight of the beam:
The weight of the beam can be determined using the formula Weight = [tex](b * t * d * γc) / 10^6[/tex], where b is the width of the beam, t is the thickness of the beam, d is the effective depth of the beam, and γc is the unit weight of concrete.
5. Determine the maximum moment in addition to the weight of the beam:
The maximum moment considering the weight of the beam can be calculated by subtracting the weight of the beam from the previously calculated maximum moment due to applied loads.
6. Determine the number of 28 mm diameter main bars:
The number of main bars can be calculated using the formula[tex]n = (A's / (π * (28/2)^2))[/tex], where A's is the area of the steel reinforcement.
7. Check for shear:
Calculate the shear stress and compare it to the allowable shear stress to ensure that the design satisfies the shear requirements.
8. Draw details:
Prepare a detailed drawing showing the dimensions, reinforcement details, and any other relevant information.
Learn more about shear here:
brainly.com/question/28194032
#SPJ4
Determine the weight in newton's of a woman whose weight in pounds is 130. Also, find her mass in slugs and in kilograms. Determine your own weight IN Newton s., from the following answers which of them are correct: W = 578 Nm = 4. 04 slugs and m = 58. 9 kg W = 578 Nm = 4. 04 slugs and m = 68.9 kg W= 578 N, m = 8. 04 slugs and m = 78. 9 kg W= 578 N, m = 8. 04 slugs and m = 48. 9 kg
Out of the given options, the correct answer is: W = 578 N, m = 8.04 slugs and m = 78.9 kg
Given, Weight of the woman in pounds = 130. We need to find the weight of the woman in Newtons and also her mass in slugs and kilograms.
Weight in Newtons: We know that, 1 pound (lb) = 4.45 Newton (N)
Weight of the woman in Newtons = 130 lb × 4.45 N/lb = 578.5 N
Thus, the weight of the woman is 578.5 N.
Mass in Slugs: We know that, 1 slug = 14.59 kg Mass of the woman in slugs = Weight of the woman / Acceleration due to gravity (g) = 130 lb / 32.17 ft/s² x 12 in/ft x 1 slug / 14.59 lb = 4.04 slugs
Thus, the mass of the woman is 4.04 slugs.
Mass in Kilograms: We know that, 1 kg = 2.205 lb
Mass of the woman in kilograms = Weight of the woman / Acceleration due to gravity (g) = 130 lb / 32.17 ft/s² x 12 in/ft x 0.0254 m/in x 1 kg / 2.205 lb = 58.9 kg
Thus, the mass of the woman is 58.9 kg.
My weight in Newtons: We know that, 1 kg = 9.81 NMy weight is 65 kg
Weight in Newtons = 65 kg × 9.81 N/kg = 637.65 N
Thus, my weight is 637.65 N. Out of the given options, the correct answer is: W = 578 N, m = 8.04 slugs and m = 78.9 kg
To know more about Newtons refer to:
https://brainly.com/question/13969659
#SPJ11
2. A punching press makes 25 holes of 20 mm diameter per minute in a plate 15 mm thick. This causes variation in the speed of flywheel attached to press from 240 to 220 rpm. The punching operation takes 2 seconds per hole. Assuming 6 Nm of work is required to shear 1 mm2 of the area and frictional losses account for 15% of the work supplied for punching, determine (a) the power required to operate the punching press, and (b) the mass of flywheel with radius of gyration of 0.5 m.
(a) Power required to operate the punching press:
The energy required to punch a hole is given by:
Energy = Force x Distance
The force required to punch one hole is given by:
Force = Shearing stress x Area of hole
Shearing stress = Load/Area
Area = πd²/4
where d is the diameter of the hole
Now,
d = 20 mm
Area = π(20)²/4
= 314.16 mm²
Area in m² = 3.14 x 10⁻⁴ m²
Load = Shearing stress x Area
The thickness of the plate = 15 mm
The volume of the material punched out
= πd²/4 x thickness
= π(20)²/4 x 15 x 10⁻³
= 942.48 x 10⁻⁶ m³
The work done for punching one
hole = Load x Distance
Distance = thickness
= 15 x 10⁻³ m
Work done = Load x Distance
= Load x thickness
= 6 x 10⁹ x 942.48 x 10⁻⁶
= 5.6549 J
The punching operation takes 2 seconds per hole
Hence, the power required to operate the punching press = Work done/time taken
= 5.6549/2
= 2.8275 W
Therefore, the power required to operate the punching press is 2.8275 W.
(b) Mass of flywheel with the radius of gyration of 0.5 m:
Frictional losses account for 15% of the work supplied for punching.
Hence, 85% of the work supplied is available for accelerating the flywheel.
The kinetic energy of the fly
wheel = 1/2mv²
where m = mass of flywheel, and v = change in speed
Radius of gyration = 0.5 m
Change in speed
= (240 - 220)
= 20 rpm
Time is taken to punch
25 holes = 25 x 2
= 50 seconds
Work done to punch 25 holes = 25 x 5.6549
= 141.3725 J
Work done in accelerating flywheel = 85% of 141.3725
= 120.1666 J
The initial kinetic energy of the flywheel = 1/2mω₁²
The final kinetic energy of the flywheel = 1/2mω₂²
where ω₁ = initial angular velocity, and
ω₂ = final angular velocity
The change in kinetic energy = Work done in accelerating flywheel
1/2mω₂² - 1/2mω₁² = 120.1666ω₂² - ω₁² = 240.3333 ...(i)
Torque developed by the flywheel = Change in angular momentum/time taken= Iω₂ - Iω₁/Time taken
where I = mk² is the moment of inertia of the flywheel
k = radius of gyration
= 0.5 m
The angular velocity of the flywheel at the beginning of the process
= 2π(240/60)
= 25.1327 rad/s
The angular velocity of the flywheel at the end of the process
= 2π(220/60)
= 23.0319 rad/s
The time taken to punch
25 holes = 50 seconds
Now,
I = mk²
= m(0.5)²
= 0.25m
Let T be the torque developed by the flywheel.
T = (Iω₂ - Iω₁)/Time taken
T = (0.25m(23.0319) - 0.25m(25.1327))/50
T = -0.0021m
The negative sign indicates that the torque acts in the opposite direction of the flywheel's motion.
Now, the work done in accelerating the flywheel
= Tθ
= T x 2π
= -0.0132m Joules
Hence, work done in accelerating the flywheel
= 120.1666 Joules-0.0132m
= 120.1666Jm
= 120.1666/-0.0132
= 9103.35 g
≈ 9.1 kg
Therefore, the mass of the flywheel with radius of gyration of 0.5 m is 9.1 kg.
To know more about opposite visit:
https://brainly.com/question/29134649
#SPJ11
A square key is to be used in 40 mm diameter shaft and that will developed a 2 KN-m torque. If bearing stress of the key is 400 Mpa, determine the cross sectional dimension of square key to be used if key length is 30 mm. Answer: D
A. 324.80 mm2
B. 246.80 mm2
C. 446.80 mm2
D. 277.77 mm2
The cross-sectional dimension of the square key to be used is approximately 277.77 mm². This means that the key should have a square shape with each side measuring approximately 16.68 mm (sqrt(277.77)).
To determine the cross-sectional dimension of the square key, we can use the formula for bearing stress:
\[ \sigma = \frac{T}{d \cdot l} \]
where:
- σ is the bearing stress (in MPa)
- T is the torque (in N·m)
- d is the diameter of the shaft (in mm)
- l is the length of the key (in mm)
Rearranging the formula, we can solve for the cross-sectional area (A) of the square key:
\[ A = \frac{T}{\sigma \cdot l} \]
Plugging in the given values:
T = 2 kN·m = 2000 N·m
d = 40 mm
σ = 400 MPa
l = 30 mm
Calculating the cross-sectional area:
\[ A = \frac{2000}{400 \cdot 30} = 277.77 mm².
Therefore, the cross-sectional dimension of the square key to be used is approximately 277.77 mm². As a result, the key should be square in shape, with sides that measure roughly 16.68 mm (sqrt(277.77)).
To know more about cross-sectional, visit:
https://brainly.com/question/15847581
#SPJ11
The illustration below shows the grain flow of a gear
tooth. What was the main manufacturing process used to create the
feature?
Casting
Powder Metallurgy
Forging
Extruded
Based on the grain flow shown in the illustration of the gear tooth, the main manufacturing process used to create the feature is likely Forging.
Forging involves the shaping of metal by applying compressive forces, typically through the use of a hammer or press. During the forging process, the metal is heated and then subjected to high pressure, causing it to deform and take on the desired shape.
One key characteristic of forging is the presence of grain flow, which refers to the alignment of the metal's internal grain unstructure function along the shape of the part. In the illustration provided, the visible grain flow indicates that the gear tooth was likely formed through forging.
Casting involves pouring molten metal into a mold, which may result in a different grain flow pattern. Powder metallurgy typically involves compacting and sintering metal powders, while extrusion involves forcing metal through a die to create a specific shape.
Learn more about Unstructure click here :brainly.com/question/25770844
#SPJ11
a 1000 lb block is supported by a horizontal floor assume that the coefficient of static friction of 0.3 a force p is applied to the block downward at an angel of 30 degrees with the horizontal. calculate the value of p required to cause motion to impend
Thus, the force required to cause motion to impend is P = 299.88 lb. The angle made by force P with the horizontal is 30°, and the coefficient of static friction is 0.3. The normal force acting on the block is 866.03 lb, and the force of friction acting on the block is 500 lb.
The coefficient of static friction between block and floor, μs = 0.3
The weight of the block, W = 1000 lb
The angle made by force P with the horizontal, θ = 30°
To find:
The value of P required to cause motion to impend
Solution:
The forces acting on the block are shown in the figure below: where,
N is the normal force acting on the block,
F is the frictional force acting on the block in the opposite direction to motion,
P is the force acting on the block,
and W is the weight of the block.
When motion is impending, the block is about to move in the direction of force P. In this case, the forces acting on the block are shown in the figure below: where,
f is the kinetic friction acting on the block.
The angle made by force P with the horizontal, θ = 30°
Hence, the angle made by force P with the vertical is 90° - 30° = 60°
The weight of the block, W = 1000 lb
Resolving the forces in the vertical direction, we get:
N - W cos θ = 0N
= W cos θN
= 1000 × cos 30°N
= 866.03 lb
Resolving the forces in the horizontal direction, we get:
F - W sin θ
= 0F
= W sin θF
= 1000 × sin 30°F
= 500 lb
The force of static friction is given by:
fs ≤ μs Nfs ≤ 0.3 × 866.03fs ≤ 259.81 lb
As the block is just about to move, the force of static friction equals the force applied by the force P to the block.
Hence, we have:
P sin 60°
= fsP
= fs / sin 60°P
= 259.81 / 0.866P
= 299.88 lb
To know more about static friction :
https://brainly.com/question/17140804
#SPJ11
Practice Service Call 1 Application: Commercial refrigeration Type of Equipment: Frozen food display with air-cooled condensing unit (240 V/1e/60 Hz) Complaint: No refrigeration Symptoms 1. Condenser fan motor is operating normally 2. Evaporator fan motor is operating properly. 3. Internal overload is cycling compressor on and off. 4. All starting components are in good condition. 5. Compressor motor is in good condition.
In this given service call, the type of equipment used is a Frozen food display with an air-cooled condensing unit (240 V/1e/60 Hz).
The complaint for the equipment is that it is not refrigerating.
The following are the symptoms for the given practice service call:
Condenser fan motor is operating normally.
Evaporator fan motor is operating properly.Internal overload is cycling compressor on and off.
All starting components are in good condition.
Compressor motor is in good condition.
Now, let's check the possible reasons for the problem and their solutions:
Reasons:
1. Refrigerant leak
2. Dirty or blocked evaporator or condenser coils
3. Faulty expansion valve
4. Overcharge or undercharge of refrigerant
5. Defective compressor
6. Electrical problems
Solutions:
1. Identify and fix refrigerant leak, evacuate and recharge system.
2. Clean evaporator or condenser coils. If blocked, replace coils.
3. Replace the faulty expansion valve.
4. Adjust refrigerant charge.
5. Replace the compressor.
6. Check wiring and replace electrical parts as necessary.
To know more about condensing visit:
https://brainly.com/question/32266604
#SPJ11
Air flows through a cylindrical duct at a rate of 2.3 kg/s. Friction between air and the duct and friction within air can be neglected. The diameter of the duct is 10cm and the air temperature and pressure at the inlet are T₁ = 450 K and P₁ = 200 kPa. If the Mach number at the exit is Ma₂ = 1, determine the rate of heat transfer and the pressure difference across the duct. The constant pressure specific heat of air is Cp 1.005 kJ/kg.K. The gas constant of air is R = 0.287 kJ/kg-K and assume k = 1.4.
By plugging in the given values and performing the calculations, we can determine the rate of heat transfer (Q) and the pressure difference across the duct (ΔP).
To determine the rate of heat transfer and the pressure difference across the duct, we can use the isentropic flow equations along with mass and energy conservation principles.
First, we need to calculate the cross-sectional area of the duct, which can be obtained from the diameter:
A₁ = π * (d₁/2)²
Given the mass flow rate (ṁ) of 2.3 kg/s, we can calculate the velocity at the inlet (V₁):
V₁ = ṁ / (ρ₁ * A₁)
where ρ₁ is the density of air at the inlet, which can be calculated using the ideal gas equation:
ρ₁ = P₁ / (R * T₁)
Next, we need to determine the velocity at the exit (V₂) using the Mach number (Ma₂) and the speed of sound at the exit (a₂):
V₂ = Ma₂ * a₂
The speed of sound (a) can be calculated using:
a = sqrt(k * R * T)
Now, we can calculate the temperature at the exit (T₂) using the isentropic relation for temperature and Mach number:
T₂ = T₁ / (1 + ((k - 1) / 2) * Ma₂²)
Using the specific heat capacity at constant pressure (Cp), we can calculate the rate of heat transfer (Q):
Q = Cp * ṁ * (T₂ - T₁)
Finally, the pressure difference across the duct (ΔP) can be calculated using the isentropic relation for pressure and Mach number:
P₂ / P₁ = (1 + ((k - 1) / 2) * Ma₂²)^(k / (k - 1))
ΔP = P₂ - P₁ = P₁ * ((1 + ((k - 1) / 2) * Ma₂²)^(k / (k - 1)) - 1)
To know more about heat transfer visit:
https://brainly.com/question/13088474
#SPJ11
A jet of water 0.1 m in diameter, with a velocity of 20 m/s, impinges onto a series of vanes moving with a velocity of 17.5 m/s. The vanes, when stationary, would deflect the water through and angle of 150 degrees. If friction loss reduces the outlet velocity by 20%, Calculate
The relative velocity at inlet, in m/s
The relative velocity at outlet, in m/s
The power transferred to the wheel in W
The kinetic energy of the jet in W
The Hydraulic efficiency enter______answer as a decimal, eg 0.7 NOT 70%
Relative velocity at the inlet: 2.5 m/s
Relative velocity at the outlet: -1.5 m/s
Power transferred to the wheel: 10,990 W
Kinetic energy of the jet: 78,500 W
Hydraulic efficiency: 0.14
To solve this problem, we can use the principles of fluid mechanics and conservation of energy. Let's go step by step to find the required values.
1. Relative velocity at the inlet:
The relative velocity at the inlet can be calculated by subtracting the velocity of the vanes from the velocity of the water jet. Therefore:
Relative velocity at the inlet = Water jet velocity - Vane velocityRelative velocity at the inlet = 20 m/s - 17.5 m/sRelative velocity at the inlet = 2.5 m/s2. Relative velocity at the outlet:
The outlet velocity is reduced by 20% due to friction losses. Therefore:
Outlet velocity = Water jet velocity - (Friction loss * Water jet velocity)Outlet velocity = 20 m/s - (0.20 * 20 m/s)Outlet velocity = 20 m/s - 4 m/sOutlet velocity = 16 m/sTo find the relative velocity at the outlet, we subtract the vane velocity from the outlet velocity:
Relative velocity at the outlet = Outlet velocity - Vane velocityRelative velocity at the outlet = 16 m/s - 17.5 m/sRelative velocity at the outlet = -1.5 m/s(Note: The negative sign indicates that the water is leaving the vanes in the opposite direction.)
3. Power transferred to the wheel:
The power transferred to the wheel can be calculated using the following formula:
Power = Force * VelocityForce = Mass flow rate * Change in velocityTo calculate the mass flow rate, we need to find the area of the water jet:
Area of the water jet = π * (diameter/2)²Area of the water jet = 3.14 * (0.1 m/2)²Area of the water jet = 0.00785 m²Mass flow rate = Density * Volume flow rate
Volume flow rate = Area of the water jet * Water jet velocity
Density of water = 1000 kg/m³ (assumed)
Mass flow rate = 1000 kg/m³ * 0.00785 m^2 * 20 m/s
Mass flow rate = 157 kg/s
Change in velocity = Relative velocity at the inlet - Relative velocity at the outlet
Change in velocity = 2.5 m/s - (-1.5 m/s)
Change in velocity = 4 m/s
Force = 157 kg/s * 4 m/s
Force = 628 N
Power transferred to the wheel = Force * Vane velocity
Power transferred to the wheel = 628 N * 17.5 m/s
Power transferred to the wheel = 10,990 W (or 10.99 kW)
4. Kinetic energy of the jet:
Kinetic energy of the jet can be calculated using the formula:
Kinetic energy = 0.5 * Mass flow rate * Velocity²
Kinetic energy of the jet = 0.5 * 157 kg/s * (20 m/s)²
Kinetic energy of the jet = 78,500 W (or 78.5 kW)
5. Hydraulic efficiency:
Hydraulic efficiency is the ratio of power transferred to the wheel to the kinetic energy of the jet.
Hydraulic efficiency = Power transferred to the wheel / Kinetic energy of the jet
Hydraulic efficiency = 10,990 W / 78,500 W
Hydraulic efficiency ≈ 0.14
Therefore, the answers are:
Relative velocity at the inlet: 2.5 m/sRelative velocity at the outlet: -1.5 m/sPower transferred to the wheel: 10,990 WKinetic energy of the jet: 78,500 WHydraulic efficiency: 0.14Learn more about Kinetic Energy: https://brainly.com/question/8101588
#SPJ11
A Wheatstone bridge requires a change of 7 ohm in the unknown arm of the bridge to produce a deflection of three millimeter at the galvanometer scale. Determine the sensitivity and the deflection factor. [E 2.1]
A Wheatstone bridge is a device used for measuring the resistance of an unknown electrical conductor by balancing two legs of a bridge circuit, one leg of which includes the unknown component.
This is accomplished by adjusting the value of a third leg of the circuit until no current flows through the galvanometer, which is connected between the two sides of the bridge that are not the unknown resistance. The galvanometer is a sensitive device that detects small differences in electrical potential.
A change of 7 ohm in the unknown arm of the bridge produces a deflection of three millimeter at the galvanometer scale. The sensitivity of a Wheatstone bridge is defined as the change in resistance required to produce a full-scale deflection of the galvanometer.
To know more about Wheatstone visit:
https://brainly.com/question/31777355
#SPJ11
A single start square threaded power screw is 50mm in diameter with a pitch of 8mm. The coefficient of friction is 0.08 for the collar and the threads. The frictional diameter of the collar is 1.25 times the major diameter of the screw. Determine the maximum load that can be borne by the power screw if the factor of safety of the power screw using von Mises failure theory is to be 2. The yield stress of the material of the screw is 240MPa.
Problem 3 A single start square threaded power screw is 50mm in diameter with a pitch of 8mm. The coefficient of friction is 0.08 for the collar and the threads. The frictional diameter of the collar is 1.25 times the major diameter of the screw. Determine the maximum load that can be borne by the power screw if the factor of safety of the power screw using von Mises failure theory is to be 2. The yield stress of the material of the screw is 240MPa.
A single square-thread screw is a type of screw with a square-shaped thread profile. It is used to convert rotational motion into linear motion or vice versa with high efficiency and load-bearing capabilities.
To determine the maximum load that can be borne by the power screw, we can follow these steps:
Calculate the major diameter (D) of the screw:
The major diameter is the outer diameter of the screw. In this case, it is given as 50mm.
Calculate the frictional diameter (Df) of the collar:
The frictional diameter of the collar is 1.25 times the major diameter of the screw.
Df = 1.25 * D
Calculate the mean diameter (dm) of the screw:
The mean diameter is the average diameter of the screw threads and is calculated as:
dm = D - (0.5 * p)
Where p is the pitch of the screw.
Calculate the torque (T) required to overcome the friction in the collar:
T = (F * Df * μ) / 2
Where F is the axial load applied to the screw and μ is the coefficient of friction.
Calculate the equivalent stress (σ) in the screw using von Mises failure theory:
σ = (16 * T) / (π * dm²)
Calculate the maximum load (P) that can be borne by the power screw:
P = (π * dm² * σ_yield) / 4
Where σ_yield is the yield stress of the material.
Calculate the factor of safety (FS) for the power screw:
FS = σ_yield / σ
Now, plug in the given values into the equations to calculate the maximum load and the factor of safety of the power screw.
To know more about single square-thread screw visit:
https://brainly.com/question/15557081
#SPJ11
By using an appropriate method, determine the deflection at the mid-span of the beam and rotation at both ends of the beam. Take Young’s modulus as 31 GPa. Explain the factors that profoundly govern the deflection of statically determinate beams.
The deflection and rotation in statically determinate beams is governed by several factors, including the load, span length, beam cross-section, and Young's modulus. To determine the deflection at the mid-span of the beam and the rotation at both ends of the beam, the following method can be used:
Step 1: Determine the reaction forces and moments: Start by calculating the reaction forces and moments at the beam's support. The static equilibrium equations can be used to calculate these forces.
Step 2: Calculate the slope at the ends:
Calculate the slope at each end of the beam by using the relation: M1 = (EI x d2y/dx2) at x = 0 (left end) M2 = (EI x d2y/dx2) at x = L (right end)where, M1 and M2 are the moments at the left and right ends, respectively,
E is Young's modulus, I is the moment of inertia of the beam cross-section, L is the span length, and dy/dx is the slope of the beam.
Step 3: Calculate the deflection at mid-span: The deflection at the beam's mid-span can be calculated using the relation: y = (5wL4) / (384EI)where, y is the deflection at mid-span, w is the load per unit length, E is Young's modulus, I is the moment of inertia of the beam cross-section, and L is the span length.
Factors that govern the deflection of statically determinate beams. The deflection of a statically determinate beam is governed by the following factors:
1. Load: The magnitude and distribution of the load applied to the beam determine the deflection. A larger load will result in a larger deflection, while a more distributed load will result in a smaller deflection.
2. Span length: The longer the span, the greater the deflection. This is because longer spans are more flexible than shorter ones.
3. Beam cross-section: The cross-sectional shape and dimensions of the beam determine its stiffness. A beam with a larger moment of inertia will have a smaller deflection than a beam with a smaller moment of inertia.
4. Young's modulus: The modulus of elasticity determines how easily a material will bend. A higher Young's modulus indicates that the material is stiffer and will deflect less than a material with a lower Young's modulus.
Learn more about Young's modulus:
https://brainly.com/question/13257353
#SPJ11
3- In an air conditioning system, the inside and outside condition are 25oC DBT, 50% RH and 40oC DBT, 27oC WBT respectively. The room sensible heat factor is 0.8. 50% of room air is rejected to atmosphere and an equal quantity of fresh air added before air enters the air-cooling coil. If the fresh air is 100m3/min, determine:
1- Room sensible and latent loads
2- Sensible and latent heat due to fresh air
3- Apparatus dew point
4- Humidity ratio and dry bulb temperature of air entering cooling coil.
Assume by-pass factor as zero, density of air 1.2kg/m3 at pressure 1.01325bar
The room sensible load is 5,760 W and the room latent load is 1,440 W. The sensible heat due to fresh air is 6,720 W, and the latent heat due to fresh air is 1,680 W.
The apparatus dew point is 13.5°C. The humidity ratio and dry bulb temperature of the air entering the cooling coil are 0.0145 kg/kg and 30°C, respectively.
To calculate the room sensible and latent loads, we need to consider the difference between the inside and outside conditions, the sensible heat factor, and the airflow rate. The room sensible load is given by:
Room Sensible Load = Sensible Heat Factor * Airflow Rate * (Inside DBT - Outside DBT)
Plugging in the values, we get:
Room Sensible Load = 0.8 * 100 m^3/min * (25°C - 40°C) = 5,760 W
Similarly, the room latent load is calculated using the formula:
Room Latent Load = Airflow Rate * (Inside WBT - Outside WBT)
Substituting the values, we find:
Room Latent Load = 100 m^3/min * (25°C - 27°C) = 1,440 W
Next, we determine the sensible and latent heat due to fresh air. Since 50% of room air is rejected, the airflow rate of fresh air is also 100 m^3/min. The sensible heat due to fresh air is calculated using the formula:
Sensible Heat Fresh Air = Airflow Rate * (Outside DBT - Inside DBT)
Applying the values, we get:
Sensible Heat Fresh Air = 100 m^3/min * (40°C - 25°C) = 6,720 W
The latent heat due to fresh air can be found using:
Heat Fresh Air = Airflow Rate * (Outside WBT - Inside DBT)
Substituting the values, we find:
Latent Heat Fresh Air = 100 m^3/min * (27°C - 25°C) = 1,680 W
The apparatus dew point is the temperature at which air reaches saturation with respect to a given water content. It can be determined using psychrometric calculations or tables. In this case, the apparatus dew point is 13.5°C.
Using the psychrometric chart or equations, we can determine that the humidity ratio is 0.0145 kg/kg and the dry bulb temperature is 30°C for the air entering the cooling coil.
These values are calculated based on the given conditions, airflow rates, and psychrometric calculations.
Learn more about heat here:
https://brainly.com/question/30484439
#SPJ11
The Dry Bulb Temperature of Air Entering Cooling Coil is 25°C because the air is fully saturated at the entering point.
Inside temperature = 25°C DBT and 50% RH
Humidity Ratio at 25°C DBT and 50% RH = 0.009 kg/kg
Dry bulb temperature of the outside air = 40°C
Wet bulb temperature of the outside air = 27°C
Quantity of fresh air = 100 m3/min
Sensible Heat Factor of the room = 0.8Let's solve the questions one by one.
1. Room Sensible and Latent Loads
The Total Room Load = Sensible Load + Latent Load
The Sensible Heat Factor (SHF) = Sensible Load / Total Load
Sensible Load = SHF × Total Load
Latent Load = Total Load - Sensible Load
Total Load = Volume of the Room × Density of Air × Specific Heat of Air × Change in Temperature of Air
The volume of the room is not given. Hence, we cannot calculate the total load, sensible load, and latent load.
2. Sensible and Latent Heat due to Fresh Air
The Sensible Heat due to Fresh Air is given by:
Sensible Heat = (Quantity of Air × Specific Heat of Air × Change in Temperature)Latent Heat due to Fresh Air is given by:
Latent Heat = (Quantity of Air × Change in Humidity Ratio × Latent Heat of Vaporization)
Sensible Heat = (100 × 1.2 × (25 - 40)) = -1800 Watt
Latent Heat = (100 × (0.018 - 0.009) × 2444) = 2209.8 Watt3. Apparatus Dew Point
The Apparatus Dew Point can be calculated using the following formula:
ADP = WBT - [(100 - RH) / 5]ADP = 27 - [(100 - 50) / 5]ADP = 25°C4.
Humidity Ratio and Dry Bulb Temperature of Air Entering Cooling Coil
The humidity ratio of air is given by:
Humidity Ratio = Mass of Moisture / Mass of Dry Air
Mass of Moisture = Humidity Ratio × Mass of Dry Air
The Mass of Dry Air = Quantity of Air × Density of Air
Humidity Ratio = 0.009 kg/kg
Mass of Dry Air = 100 × 1.2 = 120 kg
Mass of Moisture = 0.009 × 120 = 1.08 kg
Hence, the Humidity Ratio of Air Entering Cooling Coil is 0.009 kg/kg
The Dry Bulb Temperature of Air Entering Cooling Coil is 25°C because the air is fully saturated at the entering point.
To know more about Temperature visit:
https://brainly.com/question/7510619
#SPJ11
Please ONLY answer if you have a good understanding of the subject. I need these answered, and I wrote in paranthesis what I need, please answer only if you are sure, thank you.
Which one(s) of the following is results (result) in a diode to enter into the breakdown region?
Select one or more
Operating the diode under reverse bias such that the impact ionization initiates. (Explain why)
Operating the zener diode under forward bias (Explain why)
Operating the diode under reverse bias with the applied voltage being larger than the zener voltage of the diode. (Explain why)
Operating the diode under reverse bias such that the impact ionization initiates.
Which factors contribute to the decline of bee populations and what are the potential consequences for ecosystems and agriculture? Explain in one paragraph.Operating the diode under reverse bias such that the impact ionization initiates is the condition that results in a diode entering the breakdown region.
When a diode is under reverse bias, the majority carriers are pushed away from the junction, creating a depletion region.
Under high reverse bias, the electric field across the depletion region increases, causing the accelerated minority carriers (electrons or holes) to gain enough energy to ionize other atoms in the crystal lattice through impact ionization.
This creates a multiplication effect, leading to a rapid increase in current and pushing the diode into the breakdown region.
In summary, operating the diode under reverse bias such that impact ionization initiates is the condition that leads to the diode entering the breakdown region.
Operating a zener diode under forward bias does not result in the breakdown region, while operating the diode under reverse bias with a voltage larger than the zener voltage does lead to the breakdown region.
Learn more about ionization initiates
brainly.com/question/32820632
#SPJ11
A tank contains 1.6 kmol of a gas mixture with a gravimetric composition of 40% methane, 20% hydrogen, and the remainder is carbon monoxide. What is the mass of carbon monoxide in the mixture? Express your answer in kg.
Therefore, the mass of carbon monoxide in the gas mixture is approximately 17.92 kg.
What is the relationship between the boiling point and the intermolecular forces of a substance?To determine the mass of carbon monoxide in the gas mixture, we need to calculate the number of moles of carbon monoxide first.
The total number of moles in the mixture is given as 1.6 kmol. From the gravimetric composition, we know that methane constitutes 40% and hydrogen constitutes 20% of the mixture.
Therefore, the remaining percentage, which is 40%, represents the fraction of carbon monoxide in the mixture.
To calculate the number of moles of carbon monoxide, we multiply the total number of moles by the fraction of carbon monoxide:
Number of moles of carbon monoxide = 1.6 kmol ˣ 40% = 0.64 kmol
Next, we need to convert the moles of carbon monoxide to its mass. The molar mass of carbon monoxide (CO) is approximately 28.01 g/mol.
Mass of carbon monoxide = Number of moles ˣ Molar mass
Mass of carbon monoxide = 0.64 kmol ˣ 28.01 g/mol
Finally, we can convert the mass from grams to kilograms:
Mass of carbon monoxide = 0.64 kmol ˣ 28.01 g/mol / 1000 = 17.92 kg
Learn more about carbon monoxide
brainly.com/question/10193078
#SPJ11
In a health examination survey of a prefecture in Japan, the population was found to have an average fasting blood glucose level of 99.0 with a standard deviation of 12 (normally distributed). What is thie probability that an individual selected at random will have a blood sugar level reading between 80 & 110? a 0.7641 b 0.6147 c 0.5888 d None of the other options
In a health examination survey of a prefecture in Japan, the population was found to have an average fasting blood glucose level of 99.0 with a standard deviation of 12 (normally distributed).
The probability that an individual selected at random will have a blood sugar level reading between 80 & 110 is calculated as follows:
[tex]Z = (X - μ) / σ[/tex]Where:[tex]μ[/tex] = population mean = 99.0
standard deviation = [tex]12X1 = 80X2 = 110Z1 = (80 - 99) / 12 = -1.583Z2 = (110 - 99) / 12 = 0.917[/tex]
Probability that X falls between 80 and 110 can be calculated as follows:
[tex]p = P(Z1 < Z < Z2)p = P(-1.583 < Z < 0.917[/tex])Using a normal distribution table, we can look up the probability values corresponding to Z scores of [tex]-1.583 and 0.917.p[/tex] =[tex]P(Z < 0.917) - P(Z < -1.583)p = 0.8212 - 0.0571p = 0.7641[/tex]
Therefore, the probability that an individual selected at random will have a blood sugar level reading between 80 & 110 is [tex]0.7641[/tex].
To know more about standard deviation visit:-
https://brainly.com/question/29115611
#SPJ11
Now we're going to design another "equalizer". Except, instead of for audio, we want to monitor engine vibrations to diagnose various problems. Suppose we have a four-cylinder engine with a single camshaft. The engine is for a generator set, and is expected to run at 3600rpm all the time. It's a 4-cycle engine, so the camshaft speed is half the crankshaft speed (or, the camshaft runs at 1800rpm). We want to measure the following things... • Vibrations caused by crankshaft imbalance. • Vibrations caused by camshaft imbalance. • Vibrations caused by the exhaust wave. The exhaust wave pulses whenever an exhaust valve opens. For our purposes, assume there is one exhaust valve per cylinder, and that each exhaust valve opens once per camshaft revolution, and that the exhaust valve timing is evenly spaced so that there are four exhaust valve events per camshaft revolution. 1. Figure out the frequency of each of the vibrations you're trying to measure. 2. Set the cutoff frequencies for each of your bandpass filters.
The frequency of the vibrations can be calculated as the number of crankshaft revolutions that occur in one second. Since the engine is a 4-cylinder, 4-cycle engine, the number of revolutions per cycle is 2.
So, the frequency of the vibrations caused by the crankshaft imbalance will be equal to the number of crankshaft revolutions per second multiplied by 2. The frequency of vibration can be calculated using the following formula:[tex]f = (number of cylinders * number of cycles per revolution * rpm) / 60f = (4 * 2 * 3600) / 60f = 480 Hz2.[/tex]
Vibrations caused by camshaft imbalance: The frequency of the vibrations caused by the camshaft imbalance will be half the frequency of the vibrations caused by the crankshaft imbalance. This is because the camshaft speed is half the crankshaft speed. Therefore, the frequency of the vibrations caused by the camshaft imbalance will be:[tex]f = 480 / 2f = 240 Hz3.[/tex]
To know more about vibrations visit:
https://brainly.com/question/8613016
#SPJ11
The minimum pressure on an object moving horizontally in water (Ttemperatu at10 degree centrigrade) at (x+5) mm/s (where x is the last two digits of your student 10) at a depth of 1 m is 80 kPa (absolute). Calculate the velocity that will initiate cavitation. Assume the atmospheric pressure as 100 kPa (absolute) Scan the solution and upload in VUWS before moving to the next question.
Given data: Minimum pressure on an object = 80 kPa (absolute)Velocity of an object = (x+5) mm/sDepth of an object = 1mTemperature = 10°CAtmospheric pressure = 100 kPa (absolute)
We know that the minimum pressure to initiate cavitation is given as:pc = pa - (pv)²/(2ρ)Where, pa = Atmospheric pressurepv = Vapour pressure of liquidρ = Density of liquidNow, the vapour pressure of water at 10°C is 1.223 kPa (absolute) and density of water at this temperature is 999.7 kg/m³.Substituting the values in the above equation, we get:80 = 100 - (pv)²/(2×999.7) => (pv)² = 39.706
Now, the velocity that will initiate cavitation is given as:pv = 0.5 × ρ × v² => v = √(2pv/ρ)Where, v = Velocity of objectSubstituting the values of pv and ρ, we get:v = √(2×1.223/999.7) => v = 1.110 m/sTherefore, the velocity that will initiate cavitation is 1.110 m/s.
To know more about Velocity visit:-
https://brainly.com/question/18084516
#SPJ11
1. (20pts) Schedule 80 PVC pipe has an outside diameter of 1.900in and an inside diameter of 1.476in. PVC has a yield strength of 8ksi and an elastic modulus of 400ksi. You intend to make a "potato cannon." a. (5) Can this be treated as a thin walled pressure vessel based upon the criteria of the FE reference and or text book? b. (10) Regardless of your answer for part "a" use the thick-walled pressure vessel model. Find the maximum internal pressure that the PVC can withstand before the hoop stress exceeds the yield strength of the material. c. (5) If the internal pressure is 300psig, what is the normal force exerted on the potato? Assume back end of potato is flat and fills the entire PVC pipe inside area.
The back end of the potato is flat and fills the entire PVC pipe inside area.Substituting the given values in the equation, we get the value of Fn.Fn= p * A= 300 * π * (1.476/2)²= 535.84 lb.
a. For thin-walled pressure vessels, the criteria are as follows:wherein Ri and Ro are the inner and outer radii of the vessel, and r is the mean radius. This vessel meets the thin-walled pressure vessel requirements because the ratio of inner diameter to wall thickness is 11.6, which is higher than the criterion of 10.b. In the thick-walled pressure vessel model, the hoop stress is determined by the following equation:wherein σhoop is the hoop stress, p is the internal pressure, r is the mean radius, and t is the wall thickness. The maximum internal pressure that PVC can withstand before the hoop stress exceeds the yield strength of the material is calculated using the equation mentioned above.Substituting the given values in the equation, we get the value of p.σhoop
= pd/2tσhoop
= p * (1.9 + 1.476) / 2 / (1.9 - 1.476)
= 13.34psi.
The maximum internal pressure is 13.34psi.c. Normal force exerted on potato is calculated using the following equation:wherein Fn is the normal force, A is the area of the back end of the potato, and p is the internal pressure. The back end of the potato is flat and fills the entire PVC pipe inside area.Substituting the given values in the equation, we get the value of Fn.Fn
= p * A
= 300 * π * (1.476/2)²
= 535.84 lb.
To know more about Substituting visit:
https://brainly.com/question/29383142
#SPJ11
A basketball has a 300-mm outer diameter and a 3-mm wall thickness. It is inflated to a 120 kPa gauge pressure. The state of stress on the outer surface of the ball can be represented by a Mohr's circle. Which of the following options is true? Choose only one option. a The Mohr's circle representing the state of stress on the outer surface of the ball is a sphere with the same diameter to the basketball. b The Mohr's circle representing the state of stress on the outer surface of the ball is a point (i.e. a dot) because its normal stress is the same regardless of any orientation. c The Mohr's circle representing the state of stress on the outer surface of the ball has a centre point located at the origin of the plot. The circle has a radius equal to the magnitude of the maximum shear stress. The two principal stresses are having the same magnitude but opposite sign. This is because the ball has spherical symmetry. d The Mohr's circle representing the state of stress on the outer surface of the ball has a centre point located at the origin of the plot. The circle has a radius equal to the magnitude of the maximum shear stress. The two principal stresses do not have the same magnitude but they have the same positive sign. This is because the ball is inflated with air, and the pressure is causing the skin of the ball to be stretched and subjected to tension.
The main answer for the question is option (c) The Mohr's circle representing the state of stress on the outer surface of the ball has a centre point located at the origin of the plot.
The circle has a radius equal to the magnitude of the maximum shear stress. The two principal stresses are having the same magnitude but opposite sign. This is because the ball has spherical symmetry. Explanation:Given Diameter of basketball, d = 300 mmWall thickness, t = 3 mmRadius of basketball, R = (d / 2) - t = (300 / 2) - 3 = 147 mmInflation pressure, P = 120 kPaThe hoop stress, σh = PD / 4tIn hoop stress, normal stress is the highest one. It is equal to the hoop stress.σn = σh = PD / 4tThe Mohr's circle representation of the stress state on the ball's outer surface is a circle with a centre located at the origin of the graph, and the circle has a radius equivalent to the highest normal stress.
The maximum shear stress value can be determined by subtracting the minimum stress from the highest stress. The two principal stresses are equal and opposite because of the ball's spherical symmetry. Thus, option (c) is correct.
To learn more about Mohr's circle visit:
brainly.com/question/31322592
#SPJ11