Answer:
2 metersExplanation:
Wavelength = Speed/Frequency 1000 m/s ÷ 500 hz 2 mhz = sHopes this helps. Mark as brainlest plz!A 240 V circuit has 20 A flowing through it. How much power is it using?
Explanation:
P = IV
V = 240
I = 20
P = ?
P = 240 × 20
P = 4800 watts
Suppose the mass of a fully loaded module in which astronauts take off from the Moon is 2000 kg. The thrust of its engines is 8600 N. Calculate its acceleration in a vertical takeoff from the Moon.
Answer:
The acceleration during the take-off from the moon is 4.3 m/s²
Explanation:
Given;
the mass of the fully-loaded module, m = 2000 kg
The thrust of its engines, F = 8600 N
Apply Newton's second law of motion to determine the acceleration during the take-off from the moon;
F = ma
where;
a is the acceleration
a = F / m
a = 8600/2000
a = 4.3 m/s²
Therefore, the acceleration during the take-off from the moon is 4.3 m/s²
Explain the purpose of a three-valve manifold in closed tank level measurement installations.
Answer:
A three valve manifold serves to protect the capsule from being exposed to pressures above the acceptable range and also enables transmitter isolation from the loop of the process
In closed tank level measurement installations the pressure of the gas if presence of gas on top of the liquid will need to be taken account by the use of a reference connection from the level transmitter to the tank top. The valve used in pressure equalization is kept close when the process system is operating normally.
In the event that the transmitter is removed or put into service, it is necessary to ensure that the gas phase which is at the higher pressure is does not over-range the Differential Pressure DP capsule
Explanation:
In what ways do people use natural resources? What problems does use of those resources cause?
Answer:
The Challenges of Using Natural Resources
Extracting, processing and using natural resources can cause environmental problems such as: air, land and water pollution; disruption or destruction of ecosystems; and a decrease in biodiversity.
17. ____ Objects with more mass have
a. more gravity b. less gravity
c. more acceleration
d. less inerties
a. more gravity
This is the answer.
An acceleration of +3.5 m/s² results when two forces act on an object. The first
force is 100 N to the right and the second force is 40 N to the right. (A) What is
the net force on the object? (B) What is the object's mass?
Answer:
Explanation:
Since the forces oppose each other (direction), the smaller is subtracted from the larger. The net force is
Fn = 100 - 40 = 60
Part B
Fn = m * a
a = 3.5 m/s^2
Fn = 60
60 = m * a
60 = m * 3.5 Divide by 3.5
60/3.5 = m
m = 17.143
Define Velocity.
Ty!
Velocity is rate of change of position wrt frame of reference and time or alternately it's a speed with direction!
Which wave type does interference affect more?
digital
analog
Answer:
interference affects analog more
Explanation:
A hunter stood at about 60 m away from a tree. He used the bow to release the arrow in order to shoot a coconut held by a monkey in the tree. The coconut was at a height of 25 m from the ground. The hunter aimed directly at the coconut and the arrow left the bow at 45 m/s making an angle of 20 degree to the horizontal. At the moment thebhunter released the arrow, the monkey dropped the coconut such that it falls vertically from rest. Neglect air resistance and the arrow's size. What is the time taken for the arrow to hit the coconut?
Answer:
[tex]v = u + at (upward)\\ 0 = 45 \sin(20) - 9.81t \\ t = 1.56s[/tex]
Two boxes are connected by a string. The first box has a mass of 4.2 kg and the
second 2.8 kg. A string attached to the first box pulls horizontally with a force of
7.5 N. Calculate the tension in the second string if the force of friction on the first
box is 2.0 N and the force of friction on the second is 1.6 N.
Answer:
........
Explanation:
A ball rolled 12.0 m [E] in 10.0 s, hit an obstacle, and rolled straight back. After the collision, the ball rolled 8.00 m [W] in 6.00 s. What was the average velocity of the ball?
Answer:
the average velocity of the ball is 5 m/s.
Explanation:
Given;
initial position of the ball, x₁ = 12 m East
final position of the ball, x₂ = 8 m West
initial time of motion, t₁ = 10.0 s
final time of motion, t₂ = 6.0 s
The average velocity is calculated as follows;
[tex]v = \frac{\Delta x}{\Delta t} = \frac{x_1 \ - \ x_2}{t_1 \ - \ t_2}[/tex]
let the Eastward direction be positive
Let the westward direction be negative
[tex]\frac{x_1 \ - \ x_2}{t_1 \ - \ t_2} = \frac{12 \ - \ (-8)}{10 -6}= \frac{20}{4} = 5 \ m/s[/tex]
Therefore, the average velocity of the ball is 5 m/s.
The tools to distinguish the thickness of two objects of thickness of 1.92mm and the other with thickness of 1.93mm is ?
Answer:
the instrument that gives this precision is the micrometer screw
Explanation:
The high precision measurements of small parts are the general vernier and the micrometer screw.
In these two instruments the same principle is used: there is a fixed rule and a mobile one that increases precision.
Let's analyze the absolute error or precision of each instrument
* For the vernier, the precision of the fixed rule is 1 mm and there are 20 divisions (the most common); therefore the precision of the instrument is
Δx = 1 mm / 20
Δx = 0.05 mm
* For the micrometer screw, the precision of the fida rule is 0.5 mm and the number of divisions is 50, therefore the precision of the screw is
Δx = 0.5mm / 50
Δx = 0.01 mm
consequently the instrument that gives this precision is the micrometer screw
I've got a test tomorrow morning help!
A 100.0 W incandescent light bulb emits about 1.6 J of energy as useful, visible light each second. What is its efficiency?
Answer:
The efficiency is just 0.016
Explanation:
The efficiency is given by the useful energy ÷ by the total energy.
1 W is the same that 1 joule per second
If you do the math:
1.6/100=0.016
A woman on a 10-speed bicycle travels at 9m/s relative to the ground as she passes a little boy on a tricycle going in the opposite direction. If the boy is travelling at 1m/s relative to the ground , how fast does the boy appear to be moving relative to the woman
Answer:
23
Explanation:
A middle-A tuning fork vibrates with a frequency f of 440 hertz (cycles per second). You strike a middle-A tuning fork with a force that produces a maximum pressure of 5 pascals. Write a sine model that gives the pressure P as a function of the time t (in seconds).A middle-A tuning fork vibrates with a frequency f of 440 hertz (cycles per second). You strike a middle-A tuning fork with a force that produces a maximum pressure of 5 pascals. Write a sine model that gives the pressure P as a function of the time t (in seconds).
Answer:
P = 5sin(880πt)
Explanation:
We write the pressure in the form P = Asin2πft where A = amplitude of pressure, f = frequency of vibration and t = time.
Now, striking the middle-A tuning fork with a force that produces a maximum pressure of 5 pascals implies A = 5 Pa.
Also, the frequency of vibration is 440 hertz. So, f = 440Hz
Thus, P = Asin2πft
P = 5sin2π(440)t
P = 5sin(880πt)
True or False? The most reactive metals are found in Period 1 of the Periodic Table.
Hydrogen is a very reactive gas, and the alkali metals are even more reactive. In fact, they are the most reactive metals and, along with the elements in group 17, are the most reactive of all elements.
Answer:
Explanation:
true
A measurement of a change
in distance over time
Explanation:
Speed is the rate of change of distance with time.A race car reaches the finish line and the driver slows down to come to a stop. If it takes the car 10 seconds to stop at a constant acceleration of -12mph/s. What was the car's speed at the finish line?
Answer:
53.64 m/s
Explanation:
Applying,
a = (v-u)/t............. Equation 1
Where a = acceleration of the car, v = final velocity of the car, u = initial velocity of the car, t = time.
make u the subject of the equation
u = v-at............. Equation 2
From the question,
Given: a = -12 mph/s = -5.364 m/s², t = 10 seconds, v = 0 m/s (comes to stop)
Substitute these values into equation 2
u = 0-(-5.364×10)
u = 0+53.64
u = 53.64 m/s
Calculate the energy transfered when 3 of copper is heated from 20°C to 220°C
Answer:
Q = 231.6 J
Explanation:
Given that,
Mass, m = 3 g
The temperature rises from 20°C to 220°C.
We know that, the specific heat of copper is, c = 0.386 J/g K
We know that the energy transferred in heating of copper is given by :
[tex]Q=mc\Delta T\\\\Q=3\times 0.386\times (220-20)\\\\Q=231.6\ J[/tex]
So, the required energy is equal to 231.6 J.
what happens to the heat energy when you increase the length of an object
Answer: When the temperature of an object increases, the average kinetic energy of its particles increases. When the average kinetic energy of its particles increases, the object's thermal energy increases. Therefore, the thermal energy of an object increases as its temperature increases.
a simple pendulum is hollow from within and its time period is T. how is the time period of pendulum affected when:
a) ¼ of Bob is filled with mercury
b)¾ of Bob is filled with Mercury
c) the bob is completely filled with Mercury
The period of a pendulum is independent of the mass of the bob so whether it's empty or filled with something, the period remains the same.
[tex]period = 2\pi \sqrt{ \frac{length}{g} } [/tex]
If you were in a pool or ocean, what could you say about the amount of energy in a wave and the amptitude
Answer:
The amount of energy in a wave and the amplitude depends on the force applied.
Explanation:
The amount of energy in a wave is directly related to the amplitude means if the the amount of energy in a wave increases, the amplitude of that wave also increases whereas if the the amount of energy in a wave decreases the amplitude of the wave also decreases. If you jump into the pool from a higher elevation, increase occur in the amount of energy in a wave and also higher the amplitude while on the other hand, slower movement in the pool leads to smaller wave energy and lower amplitude.
What is the current measured by ammeter 4?
Answer:
I dont know
Explanation:I dont know either
Two boulders have masses of 7.5 x 106 kg and 9.2 x 105 kg. After rolling apart, their centers are separated by a distance of 124 m. Find the gravitational attraction FG between them.
Answer:
0.0299 N
Explanation:
Applying,
F = Gmm'/r²................... Equation 1
Where F = gravitational force between the boulders, m = mass of the first boulder, m' = mass of the second boulder, r = distance between the boulders, G = Universal constant.
From the question,
Given: m = 7.5×10⁶ kg, m' = 9.2×10⁵ kg, r = 124 m
Constant: G = 6.67×10⁻¹¹ Nm²/kg²
Substitute these values into equation 1
F = (6.67×10⁻¹¹× 7.5×10⁶ × 9.2×10⁵ )/124²
F = (460.23)/15376
F = 0.0299 N
Answer:
0.3 N
Explanation:
Plug in all your variables:
6.67 ⋅ 10^-11 (7.5 ⋅ 10^6) (9.2 ⋅ 10^5)
--------------------------------
(124)^2
Once you plugin, You start to multiple solving to solve your problem:
460.23
---------- = 0.02993171 N
15376
Now Simplify:
Answer = 0.03 N
can someone please help thank u
(. ^ ᴗ ^. )
3) The answer is (b) -8 m/s (pointing down)
4) The answer is (c) -9.8 m/s^2 (acceleration of a freely falling object is always due to gravity, -9.8 m/s^2, regardless of direction)
A bmw 23 goes from 0 to 60 miles per hour in 5 seconds . It is also used in the second law of motion
Answer:
Acceleration = 5.3645 m/s²
Explanation:
Given the following data;
Initial velocity, u = 0mph
Final velocity, v = 60 mph
Time, t = 5 seconds
To find the acceleration (also used in the second law of motion), we would use the following formula;
A = (v - u)/t
Conversion:
Miles per hour to meters per seconds;
0 mph = 0 mps
1 mph = 0.44704 mps
60 mph = 60 * 0.44704 = 26.8224 mps
Next, we find the acceleration;
Acceleration = (26.8224 - 0)/5
Acceleration = 26.8224/5
Acceleration = 5.3645 m/s²
A ball is initially moving with a velocity 0.5m/s. Its velocity decreases at a rate of 0.05m/s^2. How much time will it take to stop? How much distance will the ball travel before it stops
Answer: t = 10 s , s = 2,5 m
Explanation: (1) Speed v = v0 + at and (2) distance s = v0t + ½at².
Now v0 = 0.5 m/s , v = 0 and a = -0.05 m/s²
Solve from equation (1) t = -v0 / a = - 0.5 m/s / -0.05 m/s² = 10 s
Add t = 10 s to equation (2 ) s = 0.5 m/s · 10 s + 0.5· (-0.05 m/s²)· (10 s)²
= 5 m - 2,5 m = 2,5 m
describe the energy changes in mass-spring system that is oscilating horizontally.
Answer:
Explanation:
l etme y lo saoc apr aotarsy r dealkten dpo
Argon, atomic number 18, has an atomic weight of 39.9. Potassium, atomic number 19, has an atomic weight of 39.1. Which of these statements best explains why potassium has a lower atomic weight than argon?
A.
Potassium is reactive, while argon is typically inert.
B.
Potassium atoms lose electrons more easily than argon atoms.
C.
Potassium is typically a solid, while argon is typically a gas.
D.
Potassium atoms usually have fewer neutrons than argon atoms.
Answer: D
Explanation:
Atomic weight is measured by adding the number of protons and neutrons in an atom's nucleus. Argon's atomic number is 18 while potassium's is 19. This means that Argon will always have 18 protons while potassium will always have 19 protons.
To make the numbers easier to work with, round each atomic weight. We'll say the atomic weight of potassium is 39 and the atomic weight of argon is 40. To see how many neutrons each one has, I can set up a simple equation for each using the following equation:
Atomic weight = protons + neutrons
Potassium:
39 = 19 + N --> N = 20
Argon:
40 = 18 + N --> N = 22
An atom is defined by the number of protons it has, but the number of neutrons can vary. We call these isotopes, or atoms with the same number of protons but a different number of neutrons. As the math shows, argon typically has more neutrons per atom than potassium does.
How many kilowatt hours of energy did you use if you use your 1200 watt hair dryer for 6 minutes a day for a month
Answer:
1Kilowatt =1000watts
Now
Energy =Power x time
We need our power in Kilowatt and Our time in hours
Given
Power = 1200Watt
Divide this by 1000... To get its value in Kilowatt
Power = 1.2kilowatt
Time=6min
Divide by 60 to get its value in hours
Time = 6/60hr = 0.1hrs
Energy = 1.2kilowatt x 0.1hrs
=0.12kilowatt hours