An airtight box, having a lid of area 80.0 cm^2, is partially evacuated. Atmospheric pressure is 1.01 Times 10^5 Pa. A force of 108 lb is required to pull the lid off the box. The pressure in the box was:_________.

Answer:

Potential energy is the energy that is stored in an object. ... When you park your car at the top of a hill, your car has potential energy because the gravity is pulling your car to move downward; if your car's parking brake fails, your vehicle may roll down the hill because of the force of gravity.

Answer:

Specific Gravity = 0.378

Explanation:

First, we will find the force exerted by the can on the table. This force will be equal to the weight of the can:

Pressure = Force/Area = Weight/Area

Weight = Pressure*Area

where,

Area = πdiameter²/4 = π[(3.1 in)(0.0254 m/1 in)]²/4 = 4.8 x 10⁻³ m²

Weight = (510 N/m²)(4.8 x 10⁻³ m²)

Weight = 2.48 N

Now, the weight is given as:

Weight = mg

2.48 N = m(9.8 m/s²)

m = (2.48 N)/(9.8 m/s²)

m = 0.25 kg

Now, we calculate volume of can:

Volume = (Area)(Height) = (4.8 x 10⁻³ m²)(5.42 in)(0.0254 m/1 in)

Volume = 6.6 x 10⁻⁴ m³

Hence, the density of can will be:

Density of Can = m/Volume = 0.25 kg/6.6 x 10⁻⁴ m³

Density of Can = 378.32 kg/m³

So, the specific gravity of Can will be:

Specific Gravity = Density of Can/Density of Water

Specific Gravity = (378.32 kg/m³)/(1000 kg/m³)

Specific Gravity = 0.378

Answer:

Explanation:

Given;

initial velocity of the ball, u = 23 m/s

time of motion, t = 2 s

The position of the ball after 2 s is given by;

h = ut - ¹/₂gt²

h = (23 x 2) - ¹/₂ x 9.8 x 2²

h = 46 - 19.6

h = 26.4 m

The velocity of the ball after 2 s is given by;

v² = u² + 2(-g)h

v² = u² - 2gh

v² = 23² - (2 x 9.8 x 26.4)

v² = 529 - 517.44

v² = 11.56

v = √11.56

v = 3.4 m/s

Answer:

451 milliliters equals 15.25 fluid ounces

Explanation:

The rule of three or is a way of solving problems of proportionality between three known values and an unknown value, establishing a relationship of proportionality between all of them. That is, what is intended with it is to find the fourth term of a proportion knowing the other three.

To solve a direct rule of three, the following formula must be followed:

a ⇒ b

c ⇒ x

So: [tex]x=\frac{c*b}{a}[/tex]

The direct rule of three is the rule applied in this case where there is a change of units.

In this case, the rule of three can be applied in the following way: if there are 29.57 milliliters in 1 fluid ounce, in 451 milliliters how many fluid ounces are there?

[tex]fluid ounces=\frac{451 mL*1 fluid ounce}{29.57 mL}[/tex]

fluid ounces= 15.25

451 milliliters equals 15.25 fluid ounces

Acceleration of an object is the force divided by its mass. Hence, acceleration of the 100 Kg box with an applied force of 550 N is 5.5 m/s².

Acceleration is a physical quantity having both magnitude and direction. This vector measures the rate of change of velocity of a moving body. Thus, acceleration has the unit of m/s².

According to Newton's second law of motion, force acting on a body  is the product of its mass and acceleration. Thus, force is directly proportional to the mass and acceleration of the body.

Given the mass of the box = 100 Kg

 Force applied on it = 550 N.

Acceleration = 550 N / 100 Kg

                      = 5.5 m/s² ( 1 N  = 1 Kg m/s²)

Therefore, the acceleration of the box is 5.5 m/s².

To find more on acceleration, refer here:

https://brainly.com/question/2303856

#SPJ2

Answer:

The mass of the catfish is 2.13 kg

Explanation:

Period of oscillation, T = 0.19 s

spring constant, k = 2330 N/m

The period of oscillation of the spring is given by;

[tex]T = 2\pi \sqrt{\frac{m}{k} }\\\\\frac{T}{2\pi} = \sqrt{\frac{m}{k} }\\\\\frac{T^2}{4\pi^2} = \frac{m}{k}\\\\m = \frac{kT^2}{4\pi^2}[/tex]

where;

m is mass of the catfish

substitute the given values and solve for m;

[tex]m = \frac{kT^2}{4\pi^2} \\\\m = \frac{(2330)(0.19)^2}{4\pi^2} \\\\m = 2.13 \ kg[/tex]

Therefore, the mass of the catfish is 2.13 kg

Answer:

describe, explain, predict, and change/control behavior.

Explanation:

describe: What are they doing? -Pavlov noticed that dogs were salivating when they would see his lab assistant before food was presented to them. This observation acted as a description of what was happening to them.

explain: Why are they doing that?- Pavlov started to look into why they were doing it. There was a stimulus, the assistant giving them food in the past to where they started to salivate at the sight of the lab assistant

predict: What would happen if I responded in this way?- Pavlov predicted that he could get the same reaction if he used a bell as a stimulus. Using this he was able to condition dogs to salivate at the ring of the bell.

change/control: What can I do to get them to stop doing that? Because of this discovery we can use conditioning today. For example, in the classroom teachers can use conditioning with their students to make it easier, parents to teach their children right from wrong and to have good behavior. (you do this bad thing you get time out, do a good thing and I will praise you, etc) It can be used when training employees and many other places.

Answer:

0.1875 m/s leftward

Explanation:

Taking rightwards as positive

We are given:

Ball 1:

Mass (m1) = 1.5 kg

velocity (u1) = 2 m/s

Ball 2:

Mass (m2) = 2.5 kg

velocity (u2) = -1.5 m/s          [negative because it is in the opposite direction]

Speed and Direction of Ball 2:

We are told that the balls stick together after the collision

We can say that the balls have the same velocity since they are sticking together

So, Final velocity of Ball 1 (v1) = Final velocity of Ball 2 (v2) = V m/s

According to the law of conservation of momentum

m1u1 + m2u2 = m1v1 + m2v2

replacing the variables

1.5(2) + (2.5)(-1.5) = V (1.5 + 2.5)                     [v1 = v2 = V]

3 + (-3.75) = 4V

-0.75 = 4V

V = -0.75/4                                                    [dividing both sides by 4]

V = -0.1875 m/s

Hence, the balls will move at a velocity of 0.1875 m/s in the Leftward direction

Answer:

Q = PV(In 4)

Explanation:

We are told that the volume expands from V to a state with volume 4V.

Thus, initial volume is V and Final volume is 4V.

We want to find How much heat is added to the expanding gas.

For an isothermal process, the work done is calculated from;

W = nRT(In(V_f/V_i))

Where;

V_f is final volume

V_i is initial volume

Thus;

W = nRT(In(4V/V))

W = nRT(In 4)

Now, from ideal gas equation, we know that;

PV = nRT

Thus;

W = PV(In 4)

Now from first law of thermodynamics, we know that internal energy is zero and thus; Q = W

Where Q is quantity of heat

Thus;

Q = PV(In 4)

Answer:

v = 120 m/s

Explanation:

We are given;

earth's radius; r = 6.37 × 10^(6) m

Angular speed; ω = 2π/(24 × 3600) = 7.27 × 10^(-5) rad/s

Now, we want to find the speed of a point on the earth's surface located at 3/4 of the length of the arc between the equator and the pole, measured from equator.

The angle will be;

θ = ¾ × 90

θ = 67.5

¾ is multiplied by 90° because the angular distance from the pole is 90 degrees.

The speed of a point on the earth's surface located at 3/4 of the length of the arc between the equator and the pole, measured from equator will be:

v = r(cos θ) × ω

v = 6.37 × 10^(6) × cos 67.5 × 7.27 × 10^(-5)

v = 117.22 m/s

Approximation to 2 sig. figures gives;

v = 120 m/s

Explanation:

Perspective- the art of drawing solid objects on a two-dimensional surface so as to give the right impression of their height, width, depth, and position in relation to each other when viewed from a particular point.

Answer:

e. none of these

Explanation:

An object in FREE-FALL on the MOON would experience only acceleration

Answer:

penis

Explanation:

Answer:

For any given projector, the width of the image (W) relative to the throw distance (D) is know as the throw ratio D/W or distance over width. So for example, the most common projector throw ratio is 2.0. This means that for each foot of image width, the projector needs to be 2 feet away or D/W = 2/1 = 2.0.

Answer:

Ek = 196.2 [J]

Explanation:

The question concerns the KE kinetic energy.

That is, we must find the kinetic energy at the moment the cannon is fired and the kinetic energy of when the ball hits the ground after having fallen 20 meters.

At the moment when the ball is fired it is 20 meters above ground level. If the ground level is taken as the reference level of potential energy, where it is equal to zero, in this way when the ball is at the highest (20 meters) you have the maximum potential energy.

In this way, the energy in the initial state is equal to the sum of the kinetic energy plus the potential energy. As the energy is conserved this same energy will be present when the ball hits the ground, where the potential energy is zero and will have only kinetic energy.

[tex]E_{1}=E_{2}\\E_{k1}+E_{p1}=E_{k2}\\\frac{1}{2} *m*v^{2} +m*g*h=E_{k2}\\E_{k2}=0.5*1*(5)^{2} +1*9.81*20\\E_{k2}=208.7[J][/tex]

The kinetic energy in the initial state can be easily calculated by means of the following equation.

[tex]E_{k1}=\frac{1}{2} *m*v^{2}\\E_{k1}=0.5*1*(5)^{2}\\E_{k1}=12.5 [J][/tex]

Therefore the change in KE

[tex]E_{k} = 208.7 - 12.5\\E_{k} = 196.2 [J][/tex]

Answer:

20.0V

SANA MAKATULONG

The voltage drop across the 10.0-ohm resistor would be 20.0 volt.

Resistance is the obstruction of electrons in an electrically conducting material.

The mathematical relation for resistance can be understood with the help of the empirical relation provided by Ohm's law.

V=IR

For calculating equivalent resistance in series combination.

Re = R1  + R2 + R3

For the given problem the total resistance of the circuit would be as all the three resistors are connected in the series combination.

Re= 10+20+30

Re=60 ohm

As given in the figure all the resistance are connected in the series combination therefore the current flowing through them would be the same.

For the given problem we have to design and construct a circuit that has two resistors connected in series.

By using Ohms law

V=IR

120 = 60×I

I = 2 ampere

Given that we have a 120 V battery, that will produce a current of 2 Ampere

By using Ohm's law we can calculate the voltage drop across a 10-ohm resistor

V=IR

  =2×10

  = 20 volt

Thus, the voltage drop across the 10.0-ohm resistor comes out to be 20.0 volt.

Learn more about resistance from here

brainly.com/question/14547003

#SPJ2

Answer:

[tex]\displaystyle x=10\sqrt{3}\ m/s[/tex]

[tex]y=10\ m/s[/tex]

Explanation:

Rectangular coordinates of vectors in 2D

Given a vector with a magnitude v and angle θ with respect to the positive horizontal direction, the x and y components of the vector are given by:

[tex]x=v\cos\theta[/tex]

[tex]y=v\sin\theta[/tex]

The soccer ball is kicked upward at an angle θ = 30° and at a speed v=20 m/s.

The rectangular components of the vector are:

[tex]x=20\cos 30^\circ[/tex]

[tex]\displaystyle x=20\cdot \frac{\sqrt{3}}{2}[/tex]

Operating:

[tex]\mathbf{\displaystyle x=10\sqrt{3}\ m/s}[/tex]

[tex]y=20\sin 30^\circ[/tex]

[tex]\displaystyle y=20\cdot \frac{1}{2}[/tex]

Operating:

[tex]\mathbf{y=10\ m/s}[/tex]

Answer:

Explanation:

step one:

given data

velocity v=34.2m/s

time t= 8.7s

Step two

Required is the distance the cheetah has covered on the condition

we know that speed= distance/time

make distance subject of formula we have

distance= velocity *time

distance= 34.2*8.7

distance = 297.54m

Therefore the displacement the cheetah covered at that velocity

is 297.54m

Answer:

-20°C

Explanation:

The specific heat capacity of ice using the cgs system is 0.5cal/g°C

The enthalpy change is calculated as follows

ΔH=MC∅ where M represents mass C represents specific heat and ∅ represents the temperature change.

10cal = 2g×0.5cal/g°C×∅

∅=10cal/(2g×0.5cal/g°C)

∅=10°C

Final temperature= -30°C+ 10°C= -20°C

Answer:

-20 degrees Celsius

djsksjhdnenhxndjjdjd

Answer:

e. 55.0 m

Explanation:

Given;

diameter of the aluminum wire, d = 0.865 mm

radius of the wire, r = d/2 = 0.4325 mm = 0.4325 x 10⁻³ m

resistivity of the wire, ρ = 2.65 x 10⁻⁸ Ω-m

resistance of the wire, R = 2.48 Ω

The resistance of a wire is given by;

[tex]R = \frac{\rho \ L}{A} \\\\[/tex]

where;

L is length of the wire

A is area of the wire = πr² = π(0.4325 x 10⁻³ )² = 5.877 x 10⁻⁷ m²

Substitute the givens and solve for L,

[tex]L = \frac{RA}{\rho} \\\\L = \frac{(2.48)(5.877*10^{-7})}{2.65*10^{-8}}\\\\L = 55.0 \ m[/tex]

Therefore, the length of the wire is 55.0 m

Answer:

horizontal component=fcostita

=150cos60

use calculator to evaluate it

for vertical=fsintita

=150sin60

Alpha Centauri is 4.4 lightyears away. Traveling at 1/10 speed of light it would take you 44 years.

Answer:

[tex]J = 3~Kg.m/s[/tex]

Explanation:

Impulse and Momentum

The impulse-momentum theorem states that the change in momentum of an object equals the impulse applied to it.

The equation can be written as follows:

[tex]J =\Delta p = p_2-p_1[/tex]

Where:

J    = Impulse

p2 = Final Momentum

p2 = Initial Momentum

The momentum can be calculated as:

p = m.v

Where m is the mass of the object and v is the velocity.

The tennis ball with mass m=60 g = 0.06 Kg was served from rest (v1=0) to v2=50 m/s. The change in momentum is:

[tex]\Delta p = 0.06Kg~50~m/s-0[/tex]

[tex]\Delta p = 3~Kg.m/s[/tex]

Thus the impulse is:

[tex]\marhbf{J = 3~Kg.m/s}[/tex]

Answer:

v₁ = 0.375 m / s ,   x = 0.335 m

Explanation:

Let's analyze this interesting exercise, the block moves and has a friction force with the tile, we assume that the speed of the block is constant, so the friction force opposes the block movement. For the only force that acts (action and reaction) this friction force exerted by the block that is in the direction of movement of the tile.

We can also see that the isolated system formed by the block and the tile will reach a stable speed where friction cannot give the system more energy, this speed can be found by treating the system with the conservation of linear momentum.

initial moment. Right at the start of the movement

       p₀ = m v₀ + 0

final moment. Just when it comes to equilibrium

      [tex]p_{f}[/tex] = (m + M) v₁

how the forces are internal

       p₀ =p_{f}

       m v₀ = (m + M) v₁

       v₁ = m /m+M    v₀

let's calculate

       v₁ = 0.4 /(0.4 + 2.8)  3

       v₁ = 0.375 m / s

Let's apply Newton's second law to the Block, to find the friction force

Y axis

       N - W = 0

       N = W

       N = m g

where m is the mass of the block

the friction force has the formula

      fr = μ N

      fr = μ m g

We apply Newton's second law to slab    

X axis

       fr = M a

where M is the mass of the slab

       μ m g = M a

       a = μ g m / M

let's calculate

       a = 0.15  9.8  0.4 / 2.8

       a = 0.21 m / s²

With kinematics we can find the position

       v²= v₀²+2 a x

as the slab is initially at rest, its initial velocity is zero

       v² = 2 a x

       x = v2 / 2a

let's calculate

        x = 0.375²/2 0.21

        x = 0.335 m

A spring balance measures the weight of an object by opposing the force of gravity acting with force of an extending spring. May be used to determine mass as well as weight by recalibrating the scale. Some spring balances are available in gram or kilogram markings and are used to measure the mass of an object. Spring balances consist of a cylindrical tube with a spring inside. One end (at the top) is fixed to an adjuster which can be used to calibrate the device. The other end is attached to a hook on which you can hang masses etc.

Answer:

[tex]v=\sqrt{26}~m/s[/tex]

Explanation:

Parametric Equation of the Velocity

Given the position of the particle at any time t as

[tex]r(t) = (x(t),y(t))[/tex]

The instantaneous velocity is the first derivative of the position:

[tex]v(t)=(v_x(t),v_y(t))=(x'(t),y'(t))[/tex]

The speed can be calculated as the magnitude of the velocity:

[tex]v=\sqrt{v_x^2+v_y^2}[/tex]

We are given the coordinates of the position of a particle as:

[tex]x=5t-3t^2[/tex]

[tex]y=5t[/tex]

The coordinates of the velocity are:

[tex]v_x(t)=(5t-3t^2)'=5-6t[/tex]

[tex]v_y(t)=(5t)'=5[/tex]

Evaluating at t=1 s:

[tex]v_x(1)=5-6(1)=-1[/tex]

[tex]v_y(1)=5[/tex]

The velocity is:

[tex]v=\sqrt{(-1)^2+5^2}[/tex]

[tex]v=\sqrt{1+25}[/tex]

[tex]\mathbf{v=\sqrt{26}~m/s}[/tex]

Answer:

If the speed of the merry-go-round doubles, the force you will need to exert to hang on is 400 N.

Explanation:

Given;

initial force exerted to hang on, F₁ = 100 N

The force exerted on the merry-go-round in order to hang on must be an inward force known as centripetal force.

Centripetal force is given by;

[tex]F_c = \frac{mv^2}{r} \\\\keeping \ "m" \ and \ "r" \ constant, we \ will \ have \ the \ following \ equation;\\\\\frac{F_c_1}{v_1^2} = \frac{F_c_2}{v_2^2} \\\\F_c_2 = \frac{F_c_1*v_2^2}{v_1^2}\\\\when \ the \ speed\ doubles \ i.e, v_2 = 2v_1\\\\ F_c_2 = \frac{F_c_1*(2v_1)^2}{v_1^2}\\\\ F_c_2 = \frac{F_c_1*4v_1^2}{v_1^2}\\\\F_c_2 = F_c_1 *4\\\\F_c_2 = 4(F_c_1)\\\\F_c_2 = 4 (100 \ N)\\\\F_c_2 = 400 \ N[/tex]

Therefore, If the speed of the merry-go-round doubles, the force you will need to exert to hang on is 400 N.

Answer:

ill get back to this question once i find the answer to it

Answer:

Explanation:

The car’s acceleration can be found by using the formula

[tex]a = \frac{v - u}{t} \\ [/tex]

where

v is the final velocity

u is the initial velocity

t is the time taken

a is the acceleration

From the question we have

[tex]a = \frac{25 - 15}{6} = \frac{10}{6} = \frac{5}{3} \\ = 1.666666...[/tex]

We have the final answer as

Hope this helps you

Answer:

false ..........false

Answer:

FALSE                                            

Explanation: