advantage of iron meter​

Answer:

When are resistors in series? Resistors are in series whenever the flow of charge, called the current, must flow through devices sequentially. For example, if current flows through a person holding a screwdriver and into the Earth, then  

R

1

 in Figure 1(a) could be the resistance of the screwdriver’s shaft,  

R

2

 the resistance of its handle,  

R

3

 the person’s body resistance, and  

R

4

 the resistance of her shoes.

Figure 2 shows resistors in series connected to a voltage source. It seems reasonable that the total resistance is the sum of the individual resistances, considering that the current has to pass through each resistor in sequence. (This fact would be an advantage to a person wishing to avoid an electrical shock, who could reduce the current by wearing high-resistance rubber-soled shoes. It could be a disadvantage if one of the resistances were a faulty high-resistance cord to an appliance that would reduce the operating current.)

Two electrical circuits are compared. The first one has three resistors, R sub one, R sub two, and R sub three, connected in series with a voltage source V to form a closed circuit. The first circuit is equivalent to the second circuit, which has a single resistor R sub s connected to a voltage source V. Both circuits carry a current I, which starts from the positive end of the voltage source and moves in a clockwise direction around the circuit.

Figure 2. Three resistors connected in series to a battery (left) and the equivalent single or series resistance (right).

To verify that resistances in series do indeed add, let us consider the loss of electrical power, called a voltage drop, in each resistor in Figure 2.

According to Ohm’s law, the voltage drop,  

V

, across a resistor when a current flows through it is calculated using the equation  

V

=

I

R

, where  

I

 equals the current in amps (A) and  

R

 is the resistance in ohms  

(

Ω

)

. Another way to think of this is that  

V

 is the voltage necessary to make a current  

I

 flow through a resistance  

R

.

So the voltage drop across  

R

1

 is  

V

1

=

I

R

1

, that across  

R

2

 is  

V

2

=

I

R

2

, and that across  

R

3

 is  

V

3

=

I

R

3

. The sum of these voltages equals the voltage output of the source; that is,

V

=

V

1

+

V

2

+

V

3

.

This equation is based on the conservation of energy and conservation of charge. Electrical potential energy can be described by the equation  

P

E

=

q

V

, where  

q

 is the electric charge and  

V

 is the voltage. Thus the energy supplied by the source is  

q

V

, while that dissipated by the resistors is

q

V

1

+

q

V

2

+

q

V

3

.

Explanation:

Answer:

false

Explanation:

Answer:

A turbo blade has the best features from both other types of blade. The continuous, serrated edge makes for fast cutting while remaining smooth and clean. They are mostly used to cut a variety of materials, such as tile, stone, marble, granite, masonry, and many other building materials.

Explanation:

Answer:

Masonry Saw

Explanation:

Masonry Saws can be used to cut brick, ceramic, tile and or stone.

Answer:

The ability to read electrical schematics is a really useful skill to have. To start developing your schematic reading abilities, it's important to memorize the most common schematic symbols. ... You should also be able to get a rough idea of how the circuit works, just by looking at the schematic.

Explanation:

Answer:

Without the indispensable advice of the business community, TVET Institutions will be unable to cover the gap in career knowledge required by the business community.  To develop workers who possess the knowledge and skills required by today's business entities, there is always the continual need for the educational institutions (gown) to regularly meet the business community (town).  This meeting provides the necessary ground for the institutions to develop programs that groom the workforce with skills that are needed in the current workplace.  Educational institutions that do not seek this important advice from the business community risk developing workers with outdated skills.

Explanation:

TVET Institutions mean Technical and Vocational Education and Training Institutions.  They play an important role in equipping young people to enter the world of work.  They also continue to develop programs that will improve the employability of workers throughout their careers.  They regularly respond to the changing labor market needs, adopt new training strategies and technologies, and expand the outreach of their training to current workers while grooming the young people for work.

Answer:

CLIMATE CHANGE HAS inexorably stacked the deck in favor of bigger and more intense fires across the American West over the past few decades, science has incontrovertibly shown. Increasing heat, changing rain and snow patterns, shifts in plant communities, and other climate-related changes have vastly increased the likelihood that fires will start more often and burn more intensely and widely than they have in the past.

Explanation:

Answer:

B a cast part

Explanation:

Extrusion is defined as the process of shaping material, such as aluminum, by forcing it to flow through a shaped opening in a die. Extruded material emerges as an elongated piece with the same profile as the die opening.

Forcing a solid piece of heated aluminum through a die forms: a cast part. Hence, option B is correct.

A liquid element is more often filled with concrete that has a hollow chamber in the correct form during the casting manufacturing process, and the item is then let to harden.

A casting, which is the term for the solidified component, is ejected or broken out of the mould to complete the procedure.

Thus, option B is correct.

For more details about cast part, click here:

https://brainly.com/question/13653319

#SPJ2

Answer:

Sound waves are compression waves that cause energy transfer in air molecules

Sound waves have to have a medium to travel through

Loud sounds have high amplitude and vibrate with more energy than soft sounds

Explanation:

Sound waves is a form of energy composed of compression and rare factions. Sound waves are compression waves that cause energy transfer in air molecules.

Sound is an example of a mechanical wave hence it requires a material medium for propagation.

The amplitude of a sound wave determines its loudness or volume. A larger amplitude implies that we will have a louder sound, and a smaller amplitude means that we will have a softer sound.

Answer:a

Ieieksdjd snsnsnsnsksks

Connecting rods undergo a process to alleviate manufacturing stresses from forging, a process known as cold forging.​

Forging is a metalworking process that involves shaping metal with localized compressive forces. A hammer or a die is used to deliver the blows.

Forging is frequently classified according to temperature: cold forging, warm forging, or hot forging.

The goal of forging is to make metal parts. Metal forging produces some of the most durable manufactured parts available when compared to other manufacturing methods.

Minor cracks and empty spaces in the metal are filled as the metal is heated and pressed.

Cold forging is the process of deforming a metal material at room temperature using extremely high pressure. The slug is placed in a die and compressed by a press until it fits into the desired shape.

Thus, the answer is cold forging.

For more details regarding forging, visit:

https://brainly.com/question/14235193

#SPJ2

Answer: Rc = 400 Ω and Rb = 57.2 kΩ

Explanation:

Given that;

VCE = 5V

VCC = 15 V

iC = 25 mA

β = 100

VD₀ = 0.7 V

taking a look at the image; at loop 1

-VCC + (i × Rc) + VCE = 0

we substitute

-15 + ( 25 × Rc) + 5 = 0

25Rc = 10

Rc = 10 / 25

Rc = 0.4 k

Rc = 0.4 × 1000

Rc = 400 Ω

iC = βib

25mA = 100(ib)

ib = 25 mA / 100

ib = 0.25 mA

ib = 0.25 × 1000

ib = 250 μAmp

Now at Loop 2

-Vcc + (ib×Rb) + VD₀ = 0

-15 (250 × Rb) + 0.7 = 0

250Rb = 15 - 0.7

250Rb = 14.3

Rb = 14.3 / 250

Rb = 0.0572 μ

Rb = 0.0572 × 1000

Rb = 57.2 kΩ

Therefore Rc = 400 Ω and Rb = 57.2 kΩ

Answer:

Air speed in the wind-tunnel [tex]v_{2}[/tex] = 27.5 m/s

Explanation:

Given data :

Manometer reading ; p1 - p2 = 45 mm of water

Pressure at section ( I ) p1 = 100 kPa ( abs )

temperature ( T1 ) = 25°C

Pw ( density of water ) = 999 kg/m3

g = 9.81 m/s^2

next we apply Bernoulli equation at section 1 and section 2

p1 - p2 = [tex]\frac{PairV^{2} _{2} }{2}[/tex]     ----------  ( 1 )

considering  ideal gas equation

Pair ( density of air ) = [tex]\frac{P}{RT}[/tex] ------------------- ( 2 )

R ( constant ) = 287 NM/kg.k

T = 25 + 273.15 = 298.15 k

P1 = 100 kN/m^2 = 100 * 10^3 or N/m^2

substitute values into equation ( 2 )

= 100 * 10^3 / (287 * 298.15)

= 1.17 kg/m^3

Also note ; p1 - p2 = PwgΔh  ------- ( 3 )

finally calculate the Air speed in the wind-tunnel test section by equating equation ( 1 ) and ( 3 )

[tex]\frac{PairV^{2} _{2} }{2}[/tex]   =  PwgΔh  

[tex]V^{2} _{2}[/tex] = [tex]\frac{2*999* 9.81* 0.045}{1.17}[/tex]  =  753.86

[tex]v_{2}[/tex] = 27.5 m/s