Answer:
b) a = 52.26 m / s², a ’= 13.06 m / s², c) N = 2.79 10⁴ N, d) N = 1.89 10³ N
Explanation:
a) In the attached we can see the free body diagrams for the two positions, position A in the lower part of the circle and position B in the upper part of the circle
b) Let's start at point A
Let's use that the acceleration is centripetal
a = v² / r
let's calculate
a = 28² / 15.0
a = 52.26 m / s²
as they relate it is centripetal it is directed towards the center of the circle, therefore for this point it is directed vertically upwards
Point B
a ’= 142/15
a ’= 13.06 m / s²
in this case the acceleration is vertical downwards
c) The values of the normal force
point A
let's use Newton's second law
∑ F = m a
N- W = m a
N = mg + ma
N = m (g + a)
N = 450.0 (9.8 + 52.25)
N = 2.79 10⁴ N
d) Point B
-N -W = m (-a)
N = ma -m g
N = m (a-g)
N = 450.0 (14.0 - 9.8)
N = 1.89 10³ N
What is the acceleration of a car that goes from 0 MS to 60 MS and six seconds
if a car travels 200 m to the east in 8.0 s what is the cars average velocity?
Answer:
25 m/s
Explanation:
200/8 = 25
A soccer ball was kicked over the edge of a wall and traveled 35 m horizontally at a speed of 5.6m/s. Calculate the vertical height of the wall.
Answer:
Are you sure it was soccer ball? Or meine hearts
Explanation:
QUCIK!! SOMEONE PLEASE HELP! I’LL MARK BRAINLIEST!!
Answer:
A. v = √2gh
B. No! The final velocity does not depend on the mass of the car.
C. Yes! the final velocity depends on the steepness of the hill
D. 3.28 m/s
Explanation:
A. Determination of the final velocity.
½mv² = mgh
Cancel out m
½v² = gh
Cross multiply
v² = 2gh
Take the square root of both side
v = √2gh
B. Considering the formula obtained for the final velocity i.e
v = √2gh
We can see that there is no mass (m) in the formula.
Thus, the final velocity does not depend on the mass of the car.
C. Considering the formula obtained for the final velocity i.e
v = √2gh
We can see that there is height (h) in the formula.
Thus, the final velocity depends on the steepness of the hill
D. Determination of the final velocity.
Height (h) = 0.55 m
Acceleration due to gravity (g) = 9.8 m/s²
Velocity (v) =?
v = √2gh
v = √(2 × 9.8 × 0.55)
v = √10.78
v = 3.28 m/s
Please help 25 points!
Three waves with frequencies of 1 Hertz (Hz), 3 Hz, and 9Hz travel at the same speed. Which of the following statements is correct?
A. The 1 Hz wave contains the most energy.
B. The crests of all three waves are of equal height.
C. The wavelength of the 9Hz wave is three times that of the 3 Hz wave.
D. The 1 Hz wave has the longest wavelength.
Answer:
B
Explanation:
The crest of all three waves are of equal height
Given that Carbon-14 has a half-life of 5700 years, determine how long it would take for
this reduction to occur.
Answer:It will take about 3000 years
Explanation:
What two air masses creates hurricanes?
Answer:
The warm seas create a large humid air mass. The warm air rises and forms a low pressure cell, known as a tropical depression.
Explanation:
Hurricanes arise in the tropical latitudes (between 10 degrees and 25 degrees N) in summer and autumn when sea surface temperature are 28 degrees C (82 degrees F) or higher.
Answer:
air
Explanation:
what is the average velocity of a van that moves from 0 to 60 m east and 20 seconds
Explanation:
I have a lot to say it was very nice to meet my parents are u doing well I dont want too its been so much I love you so I was like u know I am not a man but you are the auditions I have been in a long long long life is a triangle and a chair for me and my parents think about the way I
2. Using a giant screw, a crew does 650 J of work to drill a hole into a rock.
The screw does 65 J of work. What is the efficiency of the screw? Show your
work. Hellpppp
Answer:
42,250
Explanation:
It goes inside=
Displacemt
It does work=
Work done
To find efficiency of jule we do=
Dicplacement × Work done
650 × 65
42,250
Please mark me as a brainlist
A particle move in the xy plane so that its position vector r=bcosQi +bsinQj+ ctk, where b, Q and c are constants. show that the partial move with constant speed.
Answer:
The speed of this particle is constantly [tex]c[/tex].
Explanation:
Position vector of this particle at time [tex]t[/tex]:
[tex]\displaystyle \mathbf{r}(t) = b\, \cos(Q)\, \mathbf{i} + b\, \sin(Q) \, \mathbf{j} + c\, t\, \mathbf{k}[/tex].
Write [tex]\mathbf{r}(t)[/tex] as a column vector to distinguish between the components:
[tex]\mathbf{r}(t) = \begin{bmatrix}b\, \cos(Q) \\ b\, \sin(Q) \\ c\, t\end{bmatrix}[/tex].
Both [tex]b[/tex] and [tex]Q[/tex] are constants. Therefore, [tex]b\, \cos(Q)[/tex] and [tex]b \sin (Q)[/tex] would also be constants with respect to [tex]t[/tex]. Hence, [tex]\displaystyle \frac{d}{dt}[b\, \cos(Q)] = 0[/tex] and [tex]\displaystyle \frac{d}{dt}[b\, \sin(Q)] = 0[/tex].
Differentiate [tex]\mathbf{r}(t)[/tex] (component-wise) with respect to time [tex]t[/tex] to find the velocity vector of this particle at time [tex]t\![/tex]:
[tex]\begin{aligned}\mathbf{v}(t) &= \frac{\rm d}{{\rm d} t} [\mathbf{r}(t)] \\ &=\frac{\rm d}{{\rm d} t} \left(\begin{bmatrix}b\, \cos(Q) \\ b\, \sin(Q) \\ c\, t\end{bmatrix}\right) \\ &= \begin{bmatrix}\displaystyle \frac{d}{dt}[b\, \cos(Q)] \\[0.5em] \displaystyle \frac{d}{dt}[b\, \sin(Q)]\\[0.5em]\displaystyle \frac{d}{dt}[c \cdot t]\end{bmatrix} = \begin{bmatrix}0 \\ 0 \\ c\end{bmatrix}\end{aligned}[/tex].
The speed [tex]v[/tex] (a scalar) of a particle is the magnitude of its velocity :
[tex]\begin{aligned}v(t) &= \| \mathbf{v}(t) \| \\ &= \left\|\begin{bmatrix}0 \\ 0 \\ c\end{bmatrix}\right\| \\ &= \sqrt{0^2 + 0^2 + c^2} = c\end{aligned}[/tex].
Therefore, the speed of this particle is constantly [tex]c[/tex] (a constant.)
A garbage truck and a minivan are moving at the same velocity.
Which automobile will have greater momentum and why? Explain your response using Newton’s second law of motion specifically.
If the garbage truck and minivan in Part A get into an accident with each other, how can safety restraints in a car can save a life? Explain your response using one of Newton’s laws.
Which of Newton’s laws of motion act upon the vehicles at the point of impact? Explain your answer.
Answer:
Part A
Newton's second law of motion states that the force applied to an object is directly proportional to the rate of change of momentum that is produced
Mathematically, we have;
F = m·v - m·u/Δt
Where;
m = The mass of the object
v = The final velocity of the object
u = The initial velocity of the object
Δt = The duration of motion of the object during change in velocity
Therefore, given that the mass, 'M', of the truck is larger than the mass, 'm', of the minivan, where the time of change in velocity Δt, and the initial and final velocities of both automobiles are the same such as in a sudden stop, the garbage ruck will exert more force than the minivan, and therefore, the garbage truck has a greater initial momentum before the automobiles are brought to a stop
Part B;
According to Newton's first law of motion, we have;
The use of a seat belt (and airbag for front seated passengers) will prevent dashboard or windscreen for the front passengers or the front seat for the passengers in the back, from being the item that stops the continued forward motion of the passengers in the car, which can lead to injury
Part C; The Newton's law of motion that act on a body at the point of impact is Newton's third law of motion, which states that the action and reaction are equal and opposite
Therefore, the action of the garbage truck on the minivan upon impact is equal to the reaction of the minivan to the force the garbage truck exerts on the minivan
Explanation:
how many pennies can 4 folds of a paper hold?
Which is an example of kinetic energy?
A. The energy stored in
ethanol
B. A ball sitting at the top of a ramp
C. A compressed spring
D. A hockey puck sliding across ice
D. A hockey puck sliding across ice
- .
?
y
(っ◔◡◔)っ ♥ chose the answer with the question marks ♥
Answer:
okay I'm a bit confused but I like the little emoji dudw
Answer:
?
Explanation:
.
is 250 000 miles from the earth to the moon" is a qualitative
Observation
TRUE
Or false
Answer:
True
Explanation:
Two identical conducting spheres are placed with their centers 0.30 m apart. One is given a charge of 12 X10^-9 C and the other is given a charge of -18 X 10^-9 C. a. Find the electric force exerted on one sphere by the other. b. The sphere are connected by a conducting wire. After equilibrium has occurred, find the electric force between the two spheres.
Answer:
Explanation:
Force between two charged conducting sphere
= k x Q₁ x Q₂ / r² , k is a constant Q₁ and Q₂ are charges and r is distance between them .
= 9 x 10⁹ x 12 x 10⁻⁹ x 18 x 10⁻⁹ / .30²
= 21600 x 10⁻⁹
= 2.16 x 10⁻⁵ N .
b )
After the spheres are joined together , there is redistribution of charge and remaining charge will be equally shared by them .
Charge on each sphere = (12 - 18 ) x 10⁻⁹ / 2
= - 3 x 10⁻⁹ C .
Force = 9 x 10⁹ x 3 x 10⁻⁹ x 3 x 10⁻⁹ / .30²
= 900 x 10⁻⁹ N .
Derase
An electric heater Consumes 1.8 MJ When connected to a 250V supply for 30 minutes. Find the power rating of the heater and the current taken from the supply
Answer:
a. Power = 1000 Watts or 1 Kilowatts.
b. Current = 4 Amperes.
Explanation:
Given the following data;
Energy consumed = 1.8MJ = 1.8 × 10^6 = 1800000 Joules
Voltage = 250V
Time = 30 minutes to seconds = 30 * 60 = 1800 seconds
To find the power rating;
Power = energy/time
Substituting into the equation, we have;
Power = 1800000/1800
Power = 1000 Watts or 1 Kilowatts.
b. To find the current taken from the supply;
Power = current * voltage
1000 = current * 250
Current = 1000/250
Current = 4 Amperes.
An accelerometer has a damping ratio of 0.5 and a natural frequency of 18,000 Hz. It is used to sense the relative displacement of a beam to which it is attached. (a)If an impact to the beam imparts a vibration at 4500 Hz, calculate the dynamic error and phase shift in the accelerometer output. (b)Calculateits resonance frequency.(c)What isthe maximumpossiblemagnitude ratio that the system can achieve
Answer:
A) i) Dynamic error ≈ 3.1%
ii) phase shift ≈ -12°
B) 79971.89 rad/s
Explanation:
Given data :
Damping ratio = 0.5
natural frequency = 18,000 Hz
a) Calculate the dynamic error and phase shift in accelerometer output at an impart vibration of 4500 Hz
i) Dynamic error
This can be calculated using magnitude ratio formula attached below is the solution
dynamic error ≈ 3.1%
ii) phase shift
This phase shift can be calculated using frequency dependent phase shift formula
phase shift ≈ -12°
B) Determine resonance frequency
Wr = 2[tex]\pi[/tex] ( 18000 [tex]\sqrt{0.5}[/tex] ) = 79971.89 rad/s
C) The maximum magnitude ratio that the system can achieve
Help plsssssssssss I write it 100 time no one answer
Answer:
1.93×10²⁸ s
Explanation:
From the question given above, the following data were obtained:
Number of electron (e) = 2×10²⁴
Current (I) = 10 A
Time (t) =?
Next, we shall determine the quantity of electricity flowing through pasing through the point. This can be obtained as follow:
1 e = 96500 C
Therefore,
2×10²⁴ e = 2×10²⁴ e × 96500 / 1 e
2×10²⁴ e = 1.93×10²⁹ C
Thus, 1.93×10²⁹ C of electricity is passing through the point.
Finally, we shall determine the time. This can be obtained as follow:
Current (I) = 10 A
Quantity of electricity = 1.93×10²⁹ C
Time (t) =?
Q = it
1.93×10²⁹ = 10 × t
Divide both side by 10
t = 1.93×10²⁹ / 10
t = 1.93×10²⁸ s
Thus, it took 1.93×10²⁸ s for 2×10²⁴ electrons to pass through the point
A storage tank has the shape of an inverted circular cone with height 12 m and base radius of 4 m. It is filled with water to a height of 10 m. Find the work required to empty the tank by pumping all of the water to the top of the tank. (The density of water is 1000 kg/m3. Assume g
Answer:
Work required to empty the tank by pumping all of the water to the top of the tank = 1674700 Kgm/s^2
Explanation:
Volume of Circular cone = V = (1/3)πr2h
where r is the radius in meters
and h is the height in meters
Substituting the given values in above equation, we get -
V = [tex]\frac{1}{3} * 3.14 * 4^2 * 10 = 167.47[/tex] cubic meters.
The force required will be equal to the mass of water in the cone
[tex]= 167.47 * 1000[/tex]
= 167470 Kg
Weight = Mass * g
= 167470 * 10
= 1674700 Kgm/s^2
Explain why two electric charges of the same magnitude, when on a collision course with each other, won't actually collide
(serious answers only)
Answer:
Explanation:
When two charges of equal magnitude and sign approach each other, they interact through Coulomb's law
F = [tex]k \frac{q_ 1q_2}{z^2 }[/tex]k q1 q2 / r2
In you case the house are of equal magnitude and sign
q1 = q2 = q
F = k q2 / r2
Let's analyze this expression, the charge is repulsive on each charge, when they are on a collision course as they approach they feel an electric field opposite to their direction of movement, this field decreases its speed, the closer they get, the greater the repulsive force. , up to the point where this force is equal to or greater than the impulse, therefore the point where the velocity reaches zero, for this reason the particles do not actually touch
An object is dropped from a bridge. A second object is thrown downwards 1.0 s later. They both reach the water 20 m below at the same instant. What was the initial speed of the second object? Neglect air resistance.