The speed of the wooden bar is changed so that the bar hits the water fewer times each second.
What happens to the frequency of the waves produced?
A. Increases
B. Does not change
C. Decreases
Answer:
c - the frequency of the waves decreases
What happens when stress builds up at faults?
A. Energy is absorbed
B. Rock can bend and break
C. Plates form on the lithosphere
D. earthquakes develop at earths surface
Answer:
The answer is D because when the faults move that is the tectonic plates moving. So earth quakes will be forming when the fault moves.
Explanation:
of the following states of motion, the one which requires balanced forces is:
A: a decrease in speed in a straight line
B: an increase in speed in a straight line
C: constant speed in a straight line
D: a change in the direction of the motion
A balanced force is required for a change in the direction of the motion.
What is a force?According to Newton's second law of motion, the force applied to a body is directly proportional to the product of mass and acceleration of the body.
Balanced forces
Balanced forces are those that are opposite in direction and equal in size. When forces are balanced there is no change in direction.
Thus, when there is change in direction, a balance force can be applied to cancel the change in direction of motion.
Learn more about balanced forces here: https://brainly.com/question/485828
Pls place the words in the right place I'll give brainless and the points!
Explanation:
you measure temperature in degrees celsius using a thermometer. Thermal energy is measured in joules. A larger volume of water will take longer to heat up but will store more energy than the smaller object. However, a smaller object will lose it's heat faster than a larger object. A cup of tea has less thermal energy than a swimming pool.
3. A simple way to state Newton’s first law is:
For every action force, there is a _______A.________ _______B.________ equal in _______C.________ and opposite in _______D.________.
yall just fill in the blanks):
Explanation:
A simple way to state Newton's first law is:
For every action force, there is a reaction force which is equal in magnitude and opposite in direction.
Emily roller skates with a constant speed
of 8 miles per hour. How far can she travel
in 3 hours? D = SxT
Answer:
She can travel 24 miles in 3 hours.
What is the definition of endothermic and exothermic?
pls help on a timer will give brainlist
Answer:
An exothermic process releases heat, causing the temperature of the immediate surroundings to rise. While an endothermic process absorbs heat and cools the surroundings
Explanation:
Answer:
Basically, endothermic feels cooler to touch than exothermic.
Explanation:
Endothermic reactions are just reactions that emit energy (in form of heat) to its surroundings. Exothermic ones, on the other hand, draw energy from its surroundings to occur.
Always think - "Endothermic is cool. Exothermic is not cool."
The force of attraction that holds two atoms together within a molecule is
Answer: Chemical bond
Explanation: This force is of an electric nature, and the attraction between electrons of one atom to the nucleus of another atom contributes to what is known as chemical bonds.
Which part of the electromagnetic spectrum is typically used to make images based on the temperatures of objects?
X-rays
radio waves
infrared light
visible light
Answer:
Which part of the electromagnetic spectrum is typically used to make images based on the temperatures of objects?
X-rays
radio waves
infrared light<<<----- CORRECT
visible light
Explanation:
Edge 2021
Infrared light is typically used to make images based on the temperatures of objects.
What is meant by electromagnetic spectrum?The range of all EM radiation arranged from high to low frequency (short to long wavelength) according to their frequency or wavelength. is known as the electromagnetic spectrum (EM).
Here,
Similar to visible light, X-rays are a type of electromagnetic radiation. X-rays have a higher energy than light, on the other hand, and can penetrate most materials, including the human body.
Images of inside body tissues and structures are produced using medical x-rays.
Electromagnetic energy in the infrared region of the spectrum can be seen by them. There is a relationship between an object's temperature and the electromagnetic radiation it releases since infrared radiation is strongly related to object temperature.
Hence,
Infrared light is typically used to make images based on the temperatures of objects.
To learn more about electromagnetic spectrum, click:
https://brainly.com/question/15576247
#SPJ5
when a material absorbs energy from light the energy causes the material to do what?
Answer:
To change.
Explanation:
The Law of Conservation of energy states that energy cannot be destroyed but can only be transformed or converted from one form to another. For example, light energy to heat energy.
When a material absorbs energy from light the energy causes the material to change.
A car's velocity changes from 40 m/s to 30 m/s in 40 seconds. What is the
acceleration of the car?
Answer:
- 0.25m/s²
Explanation:
Given parameters:
Initial velocity = 40m/s
Final velocity = 30m/s
Time taken = 40s
Unknown:
Acceleration of the car = ?
Solution:
Acceleration is the rate of change of velocity with time.
So;
Acceleration = [tex]\frac{Final velocity - Initial velocity }{time }[/tex]
Acceleration = [tex]\frac{30 - 40}{40}[/tex] = - 0.25m/s²
This implies that the car will decelerate at a rate of 0.25m/s²
A stationary 10 kg object is located on a table near the surface of the earth. The coefficient of kinetic friction between the surfaces is 0.2. A horizontal force of 40 N is applied to the object.
Answer:
2.04m/s²
Explanation:
Complete Question
A stationary 10 kg object is located on a table near the surface of the earth. The coefficient of kinetic friction between the surfaces is 0.2. A horizontal force of 40 N is applied to the object. Find the acceleration of the object.
According to Newtons second law;
\sum F_x = ma_x
F_m - F_f = ma_x
Fm is the applied force
Ff is the frictional force
m is the mass
a is the acceleration
Substitute the given values
40N - nmg = 10a
40 - 0.2(10)(9.8) = 10a
40 - 19.6 = 10a
20.4 = 10a
a = 20.4/10
a = 2.04m/s²
Hence the acceleration of the object is 2.04m/s²
Jeremy walked at an average rate of speed of 5 km/h. how far had Jeremy walked in 15 minutes?
Answer:
1 half kilometer is right answer
When we stretch a spring, which two factors affect how much elastic
potential energy is stored in it
What are all of the physics rules?
Answer:
f this bs
Explanation:
no i will not answer this
Answer: PLEASE GIVE BRIANLIEST
1. Archimedes Principle
2. Avogadro’s Law
3. Ohm's Law
4. Newton’s Laws (1642-1727)
5. Coulomb’s Law (1738-1806)
6. Stefan’s Law (1835-1883)
7. Pascal’s Law (1623-1662)
8. Hooke’s Law (1635-1703)
9. Bernoulli's Principle
10. Boyles's Law
11. Charles's Law
12. Kepler's Law
13. Law of conservation of energy
14. Tyndall effect
15. Graham’s Law
A squirrel starts at rest and accelerates at 2.3 m/s^2 for 5.22 seconds. What is it's final velocity?
Please provide the variable, number, and unit e.g., a= 1.34 m/s^2
Answer:
12.259 m/s
Explanation:
An object starting at rest and accelerating at a constant acceleration a for t seconds has a velocity of
[tex]v=at[/tex]
If we substitute in the values a = 2.3 m/s² and t = 5.22 s, we get a velocity of
[tex]2.3(5.22)=12.259[/tex] m/s
Which of the following scenarios demonstrates a transfer
between kinetic energy and potential energy?
Answer:
what scenarios? but kinetic is energy in motion (like a ball rolling) and potential is stored energy (ball laying on ground)
example (kinetic to potential) : baseball flying and and lands on the ground then stops rolling
roller coaster rolling down a hill then stopping (kinetic to potential)
roller coaster on top of a hill and then going down (potential to kinetic)
Explanation:
The acceleration due to gravity is 9.81 m/s2, towards the Earth. Rain falling from an altitude of 9,000 m would fall for about 1.5 minutes before hitting the ground (ignoring air resistance). What would be the final speed of a raindrop by the time it reaches the ground?
Answer:
the final speed of the rain is 541 m/s.
Explanation:
Given;
acceleration due to gravity, g = 9.81 m/s²
height of fall of the rain, h = 9,000 m
time of the rain fall, t = 1.5 minutes = 90 s
Determine the initial velocity of the rain, as follows;
[tex]h = ut + \frac{1}{2} gt^2\\\\9000 = 90u + \frac{1}{2} (9.8)(90)^2\\\\9000 = 90u + 39690\\\\90u = -30690\\\\u = \frac{-30690}{90} \\\\u = -341 \ m/s[/tex]
The final speed of the rain is calculated as;
[tex]v^2 = u^2 + 2gh\\\\v^2 = (-341)^2 + 2(9.8\times 9000)\\\\v^2 = 292681\\\\v = \sqrt{292681} \\\\v = 541 \ m/s[/tex]
Therefore, the final speed of the rain is 541 m/s.
Answer:
The magnitude of the final speed of a raindrop by the time it reaches the ground will be 541.45 m/s.
Explanation:
The final speed of the raindrop can be found using the following equation:
[tex] v_{f} = v_{0} - gt [/tex]
Where:
[tex]v_{f}[/tex]: is the final speed =?
[tex]v_{0}[/tex]: is the initial speed
g: is the acceleration due to gravity = 9.81 m/s²
t: is the time = 1.5 min
First, we need to find the initial speed:
[tex] y_{f} = y_{0} + v_{0}t - \frac{1}{2}gt^{2} [/tex]
Where:
[tex]y_{f}[/tex]: is the final height = 0
[tex]y_{0}[/tex]: is the initial height = 9000 m
Hence, the initial speed is:
[tex] v_{0} = \frac{y_{f} - y_{0} + \frac{1}{2}gt^{2}}{t} = \frac{0 - 9000 m + \frac{1}{2}9.81 m/s^{2}*(90 s)^{2}}{90 s} = 341.45 m/s [/tex]
Hence, the final speed is:
[tex] v_{f} = v_{0} - gt = 341.45 m/s - 9.81 m/s^{2}*90 s = -541.45 m/s [/tex]
Therefore, the magnitude of the final speed of a raindrop by the time it reaches the ground will be 541.45 m/s.
I hope it helps you!
A hiker walks with an average speed of 2.6 M Square what distance in kilometers does the hiker travel in a time of 2.8 hours
Answer:
The answer is "26.208 km"
Explanation:
Given value:
[tex]\to S= 2.6 \ \frac{m}{s}\\\\\to t= 2.8 \ hours[/tex]
Formula:
[tex]d= st\\\\d= 2.6 \times 2.8 \times \frac{60 \times 60}{1000}\\\\d= 26.208\ km[/tex]
Can anyone please help meee!!!
Answer:
The centripetal acceleration is given by
a = v 2 r = 10 2 25 = 4 m s − 2
Using Newton's Second Law, the centripetal force acting is
F = m a = 900 ⋅ 4 =3600 N
Explanation:
1. Find the momentum of an object of mass 5 kg with a velocity of 2 m/s. *
a. 2.5 kg.m/s
O b. 10 kg.m/s
c. 0.25 kg.m/s
d. 20 kg.m/s
Answer:
10kgm/s
Explanation:
Momentum = Mass * Velocity (both in standard units)
Momentum = 5 * 2 = 10kgm/s
. A hydraulic lift consists of two cylindrical pistons, one with a radius of 1.5 m and
the other with a radius of 8.0 cm. What force must be applied to the smaller piston if
a crate with a mass of 1.5x103 kg is to be raised on the larger piston?
F=42N,
Answer:
The force that must be applied to the smaller piston if the crate is to be raised by the larger piston is approximately 42 N
Explanation:
The given parameters of the hydraulic lift are;
The diameter of one of the pistons = 1.5 m
The diameter of the other pistons = 8.0 cm = 0.08 m
The mass of the crate to be lifted with the larger piston, m = 1.5 × 10³ kg
The weight of the mass to be lifted by the larger piston, W₁ = m × g
Where;
g = The acceleration due to gravity = 9.8 m/s²
Therefore;
W₁ = 1.5 × 10³ kg × 9.8 m/s² = 14,700 N
The area of the surface of the circular piston, A = π × r²
Where;
r = The piston's radius
∴ The area of the larger piston with 1.5 m radius, A₁ = π × (1.5 m)² = 7.06868347058 m² ≈ 7.07 m²
A₁ ≈ 7.07 m²
The area of the smaller piston with 0.08 m (8 cm) radius, A₂ = π × (0.08 m)² = 02010619298 m² ≈ 0.02 m²
A₂ ≈ 0.02 m²
The pressure in the fluid of the hydraulic lift is constant, therefore, we have;
The pressure applied to the larger piston with 1.5 m radius, P₁ = The pressure applied to the smaller piston with 0.08 m radius, P₂
∴ P₁ = P₂
[tex]Pressure = \dfrac{Force}{Area}[/tex]
[tex]P_1 = \dfrac{W_1}{A_1} = \ P_2 = \dfrac{F_2}{A_2}[/tex]
[tex]\therefore \dfrac{W_1}{A_1} = \ \dfrac{F_2}{A_2}[/tex]
Where, F₂, represents the force that must be applied to the smaller piston if the crate is to be raised by the larger piston;
[tex]\therefore F_2 = A_2 \times \dfrac{W_1}{A_1}[/tex]
Given that we have the ratio of two areas which have π as a factor, we have;
[tex]\therefore F_2 = A_2 \times \dfrac{W_1}{A_1} = 0.08^2 \times \pi \times \dfrac{14,700}{1.5^2 \times \pi } = 41.81 \overline 3[/tex]
The force that must be applied to the smaller piston if the crate is to be raised by the larger piston, F₂ = 41.81[tex]\overline 3[/tex] N ≈ 42 N.
What is specific heat?
Answer:
Specific heat is defined by the amount of heat needed to raise the temperature of 1 gram of a substance 1 degree Celsius (°C). Water has a high specific heat capacity which we'll refer to as simply "heat capacity", meaning it takes more energy to increase the temperature of water compared to other substances.
Explanation:
Hope this Helps
Please Mark as Brainliest
:)
Which force is an attractive force that is affected by the masses of objects?
A) tension force
B) magnetic force
C) normal force
D) gravitational force
Class: Physical Science B
Answer:
D) gravitational force
D.
because the time is used up due to irrelevant and unnecessary topics
& Every time your group conducts a meeting, nothing is accomplished
that intervene the discussion.
As the group leader, how will you keep your members focused on the
agenda of the meeting using the restriction strategy?
A. Tell them that they will get kicked out from the group if they will
B. End the meeting immediately as soon
as the group begins to
talk about other things irrelevant to the agenda.
c. Give instructions before the meeting starts to confine and limit
what they can say.
D. Show disappointment.
not cooperate.
Answer:
b because I took the quiz
explain the oscillations or motion of both types of waves
Which best explains how thermal energy is transferred when someone holds a hand above a fire?
a) It is transferred by conduction and radiation.
b) It is transferred by only convection.
c) It is transferred by only conduction.
d) It is transferred by radiation and convection.
Why we need football?
Answer:
bc we play when we are bored and some people use it as a tradition to play on thanksgiving
Three sharks are located at the vertices of an equilateral triangle whose side equals LL. They all start moving simultaneously with a constant speed vv, with the first shark heading constantly toward the second, the second toward the third, and the third toward the first. How soon will the sharks converge at one point
Answer:
They will never meet.
Explanation:
Given that three sharks are located at the vertices of an equilateral triangle whose side equals LL. They all start moving simultaneously with a constant speed vv, with the first shark heading constantly toward the second, the second toward the third, and the third toward the first. How soon will the sharks converge at one point ?
Since the three sharks are located at the vertices of an equilateral triangle whose side equals, and the first shark is moving toward the second, the second is moving toward the third, and the third shark is moving toward the first, the movement of the three shark will form a circular motion.
Since the three sharks are moving at a constant speed, the three sharks will never meet because the distances between them are also the same.
The three sharks will therefore continue to move till infinity.
If a 2 kg spring is compressed by exerting a force of 10 newtons a distance of 50 cm how much work is done?