Answer:
a) the inductance of the coil is 6 mH
b) the emf generated in the coil is 18 mV
Explanation:
Given the data in the question;
N = 570 turns
diameter of tube d = 8.10 cm = 0.081 m
length of the wire-wrapped portion l = 35.0 cm = 0.35 m
a) the inductance of the coil (in mH)
inductance of solenoid
L = N²μA / l
A = πd²/4
so
L = N²μ(πd²/4) / l
L = N²μ(πd²) / 4l
we know that μ = 4π × 10⁻⁷ TmA⁻¹
we substitute
L = [(570)² × 4π × 10⁻⁷× ( π × (0.081)² )] / 4(0.35)
L = 0.00841549 / 1.4
L = 6 × 10⁻³ H
L = 6 × 10⁻³ × 1000 mH
L = 6 mH
Therefore, the inductance of the coil is 6 mH
b)
Emf ( ∈ ) = L di/dt
given that; di/dt = 3.00 A/sec
{∴ di = 3 - 0 = 3 and dt = 1 sec}
Emf ( ∈ ) = L di/dt
we substitute
⇒ 6 × 10⁻³ ( 3/1 )
= 18 × 10⁻³ V
= 18 × 10⁻³ × 1000
= 18 mV
Therefore, the emf generated in the coil is 18 mV
How do you explain the application of regulations in locations containing baths, showers and electric floor heating, including the requirements needed?
Answer:
The application of regulations in locations are very important.
Explanation:
The application of regulations in locations are very important in order to gain more benefit from it because people choose those places that are well regulated and having more facilities. If the location has baths, showers, electric floor heaters and other necessities so the people prefer the place over another and increase of clients occurs which give more benefits to the place owners.
The aluminum rod (E1 = 68 GPa) is reinforced with the firmly bonded steel tube (E2 = 201 GPa). The diameter of the aluminum rod is d = 25 mm and the outside diameter of the steel tube is D= 45 mm. The length of the composite column is L = 761 mm. A force P = 88 kN is applied at the top surface, distributed across both the rod and tube.
Required:
Determine the normal stress σ in the steel tube.
Answer:
Explanation:
From the information given:
[tex]E_1 = 68 \ GPa \\ \\ E_2 = 201 \ GPa \\ \\ d = 25 \ mm \ \\ \\ D = 45 \ mm \ \\ \\ L = 761 \ mm \\ \\ P = -88 kN[/tex]
The total load is distributed across both the rod and tube:
[tex]P = P_1+P_2 --- (1)[/tex]
Since this is a composite column; the elongation of both aluminum rod & steel tube is equal.
[tex]\delta_1=\delta_2[/tex]
[tex]\dfrac{P_1L}{A_1E_1}= \dfrac{P_2L}{A_2E_2}[/tex]
[tex]\dfrac{P_1 \times 0.761}{(\dfrac{\pi}{4}\times .0025^2 ) \times 68\times 10^4}= \dfrac{P_2\times 0.761}{(\dfrac{\pi}{4}\times (0.045^2-0.025^2))\times 201 \times 10^9}[/tex]
[tex]P_1(2.27984775\times 10^{-8}) = P_2(3.44326686\times 10^{-9})[/tex]
[tex]P_2 = \dfrac{ (2.27984775\times 10^{-8}) P_1}{(3.44326686\times 10^{-9})}[/tex]
[tex]P_2 = 6.6212 \ P_1[/tex]
Replace [tex]P_2[/tex] into equation (1)
[tex]P= P_1 + 6.6212 \ P_1\\ \\ P= 7.6212\ P_1 \\ \\ -88 = 7.6212 \ P_1 \\ \\ P_1 = \dfrac{-88}{7.6212} \\ \\ P_1 = -11.547 \ kN[/tex]
Finally, to determine the normal stress in aluminum rod:
[tex]\sigma _1 = \dfrac{P_1}{A_1} \\ \\ \sigma _1 = \dfrac{-11.547 \times 10^3}{\dfrac{\pi}{4} \times 25^2}[/tex]
[tex]\sigma_1 = - 23.523 \ MPa}[/tex]
Thus, the normal stress = 23.523 MPa in compression.
Which one of the following answer options are your employers responsibility
Where are your answer options?
Answer:
Implement a hazard communication program
Explanation: i took the quiz
Forces always act in equal and opposite pairs
Construct the plane-stress yield envelopes in a principle stress space for both the Tresca and the von Mises yield theories using your calculated value of the yield strength to scale the envelopes. Indicate the two equivalent load paths corresponding to pure shear on the yield envelopes. Calculate the shear yield strength of Al 6061-T6 aluminum predicted by the above theories.
Answer:
Explanation:
The missing part of the question is attached in the diagram below, the second diagram shows the schematic view of the stress-strain curve and the plane stress.
From the given information:
The elastic modulus is:
[tex]E = \dfrac{\sigma}{\varepsilon} \\ \\ E = \dfrac{150 \ MPa}{0.0217} \\ \\ E = 69.124 \ GPa[/tex]
Hence, suppose 0.2% offset cuts the stress-strain curve at a designated point A from the image attached below, then the yield strength relating to the stress axis from the curve will be [tex]\sigma_y[/tex] = 270 MPa.
The shear yield strength by using von Mises criteria is estimated as;
[tex]\tau_1 = \dfrac{\sqrt{2}}{3}\sigma_y \\ \\ \tau_1 = \dfrac{\sqrt{2}}{3}*270 \\ \\ \tau_1 = 127.28 \ MPa[/tex]
The shear yield strength by using Tresca criteria is:
[tex]\tau_2 = \dfrac{1}{2}\sigma_y \\ \\ \tau_2= \dfrac{1}{2}*270 \\ \\ \tau_2 = 135 \ MPa[/tex]
Where do greywater pipes generally feed into?
-Vent stack
-Water heater
-Waste stack
-Main supply
Answer:
c Waste stack
Explanation:
What two units of measurement are used to classify engine sizes?