Answer:
Conductivity is the measure of the ease at which an electric charge or heat can pass through a material. A conductor is a material that gives very little resistance to the flow of an electric current or thermal energy.
Explanation:
brainliest plss
A series circuit is set up with an AA battery along with an mystery material and ammeter; however, there’s no current passing through.
A.Insulator
B.Conductor
C.Semiconductor
Answer:
A. Insulator
Explanation:
Since there is no current passing through at all.
I stand 0.72 meters in front of a mirror and look at the person on the other side who looks like me. That person is actually younger than me by a small amount. How much?
Answer:
Younger by nanoseconds
Explanation:
Not entirely sure :O
5. A ball weighing 10 kg rolls 200 m down a frictionless incline with a 50 degree angle to the horizontal. If the ball’s initial velocity was 0 m/s, how much does the mechanical energy of the system change by the time the ball reaches its destination? A) It increased by 12%. B) It increases by 58%. C) It decreases by 12%. D) It does not change.
Answer:
D) It does not change
Explanation:
Since there is no friction in the inclined plane. Therefore, there is no loss in the total mechanical energy of the system. So according to the law of conservation of energy we can write:
Total Mechanical Energy at Start = Total Mechanical Energy at End + Frictional Loss
Total Mechanical Energy at Start = Total Mechanical Energy at End + 0
Total Mechanical Energy at Start = Total Mechanical Energy at End
It means there is no change in the total mechanical energy of the system.
Therefore, the correct option is:
D) It does not change
A 300-g chunk of ice (of density 0.900 g/cm3) is placed in a water bucket. A 20.0-g rock, with a volume of 2.00 cm3, is placed on top of the ice before water is filled to the top. When the ice melts and the rock drops to the bottom of the buckt, how much water spills out or needs to be added to maintain full level? Ignore the possible dependence of the densities of ice and water on temperature.
Answer:
18 cm³ of water
Explanation:
The correct procedure and explanation is in the picture attached. If you have any doubts, feel free to leave in the comments.
Hope this helps
A student pushes a laptop cart down the hallway by applying 20 Newtons force. The student pushes it 10 meters and
then stops at the water fountain with the cart and haves a sip of water. While he drinks from the water fountain, what
type of work is being done to the laptop cart.
Answer:
None.
Explanation:
By definition, work is a process that it happens when an applied forcecauses an object to change its position, i.e. to have a displacement.
Since the laptop cart is at rest while he stops at the water fountain, no
net work done is on the laptop cart.
Describe the formation of galaxies.
Today's cosmologists assume that matter was not uniformly distributed in the universe after the Big Bang. Dense places attract more matter than the surrounding area according to their gravitational forces. Over the course of billions of years, these gas agglomerations eventually led to the formation of the galaxies we see today.
If a body of mass 2 kg is moving with a velocity of 30 m/s, then
on doubling its velocity the momentum becomes
a 30 kgm/s
b 90 kgm/s
C 120 kgm/s
d 60 kgm/s
HALPLPLPPLL
Answer:
d. 60
Explanation:
If a body of mass 2 kg is moving with a velocity of 30 m/s, then
on doubling its velocity the momentum becomes
a 30 kgm/s
b 90 kgm/s
C 120 kgm/s
d 60 kgm/s
HALPLPLPPLL
Answer:
120
Explanation:
A box has base dimensions of 30 cm x 30 cm and a mass of 3 kg. Calculate to what
depth it sinks when placed in a tank of water (assume the sides are sufficiently high,
so that it floats). Density of water = 1000 kgm-3. Assume g=10 ms-2 for this problem.
Answer:
60
Explanation:
A box has base dimensions of 30 cm x 30 cm and a mass of 3 kg. Calculate to what
depth it sinks when placed in a tank of water (assume the sides are sufficiently high,
so that it floats). Density of water = 1000 kgm-3. Assume g=10 ms-2 for this problem.
The center of mass of a uniform disk of radius
Ris located where?
Answer:
At the centre
Explanation:
To prove the position of the centre of mass, usually we take a strip across the circular disc and call it dy; calculate the length of the strip; calculate the mass per unit area of the disc. And then when we carry out some integral operations using R and -R as the boundaries we will arrive at y_cm = 0 which means the centre y_cm is at the centre of mass of this uniform disc.
Write a method which prevents ice from melting quickly.
Answer:
blocks of ice are usually covered with cloth or sawdust while being stored
explain why the lamp does not light when the input to the transformer is directed current
Answer:
Direct current(DC) has no time varying field because current is constant as well as there is no relatively motion between coil and core(magnetic circuit) of the transformer. So there is no induced emf in secondary coil of the transformer. Tom Mounts, field engineer, and electronics technician.
Explanation:
can i have brainly if right
what is the focalength of the combination of two thin renses of power -5D and -2D placeci in contact with each other?
Answer:
f = - 0.143 m = - 14.3 cm
Explanation:
First, we will calculate the power of the combination of lenses:
P = P₁ + P₂
where,
P = Power of Combination = ?
P₁ = Power of first lens = - 5D
P₂ = Power of second lens = - 2D
Therefore,
P = - 5D - 2D
P = - 7D
Now, the focal length can be given as:
[tex]f = \frac{1}{P} \\\\f = \frac{1}{-\ 7\ D} \\\\[/tex]
f = - 0.143 m = - 14.3 cm
Negative focal length indicates that combination will act as diverging lens.
Q: Winding roads and sharp curves are inherently dangerous
because -
A- You can't see far ahead
B- The speed limit is so slow
C- There may be other vehicles traveling in the
opposite direction
D- You may struggle to stay at the same speed
Answer:
A) you can't see far ahead
D. You may struggle to stay at the same speed.
Winding roads and sharp curves are dangerous because of centrifugal forces while taking curves, whose classic formula is described below:
[tex]F = m\cdot \frac{v^{2}}{r}[/tex] (1)
Where:
[tex]F[/tex] - Centrifugal force, in newtons.[tex]v[/tex] - Speed, in meters per second.[tex]r[/tex] - Radius of curvature, in meters per second.Sharps curves are characterized by low radii of curvature. Given that centrifugal force is inversely proportional to the square radius of curvature and it is opposed to friction force between tires and pavement, if centrifugal force is higher than maximum static friction force, then a car accident could if driver does not decelerate.
Therefore, correct choice is D.
We kindly invite to see this question on centrifugal forces: https://brainly.com/question/545816
In a single-slit experiment, the slit width is 150 times the wavelength of the light.
What is the width (in mm) of the central maximum on a screen 2.6 m behind the slit?
I have tried:
y=[(1+1/2)(lambda)(2.6m)] / (150lambda)
to bring me to
y=[(1.5)(2.6)] \ (150)
giving me a y value in mm of 26
Which of the following is a problem with the estimated age of the universe?
There are stars in our galaxy that appear to be over 15 billion years old.
The universe is shrinking, which makes it is impossible to tell how old it is.
There should be more supergiants if the universe is really about ten billion years old.
There are planets in other galaxies that are less than five billion years old.
Answer:
There are stars in our galaxy that appear to be over 15 billion years old.
Explanation:
The age of the universe is the time past since the big ban event as based on observations of the early state of the universe. The comic problem with the universe is that it's estimated to be older since the time of the big bang. It also represents a contrast with objects in the galaxies such as stars, planets that could not have been present.WILL MARK BRAINLIEST PLS HELP. A 3.33 x 10-6 F capacitor stores
8.15 x 10-4 J of energy. What is the
voltage across the capacitor?
(Pic shown)
Answer:
15.64 V
Explanation:
From the question given above, the following data were obtained:
Capacitor (C) = 3.33x10¯⁶ F
Energy (E) = 8.15×10¯⁴ J
Voltage (V) =?
The voltage across the capacitor can be obtained as follow:
E = ½CV²
8.15×10¯⁴ = 3.33x10¯⁶ × V²
Divide both side by 3.33x10¯⁶
V² = 8.15×10¯⁴ / 3.33x10¯⁶
Take the square root of both side
V = √(8.15×10¯⁴ / 3.33x10¯⁶)
V = 15.64 V
Thus, the voltage across the capacitor is 15.64 V
Answer:
22.12
Explanation:
on accellus
A bat emits a sound at a frequency of 30.0 kHz as it approaches a wall. The bat detects beats such that the frequency of the echo is 900 Hz higher than the frequency the bat is emitting. The speed of sound in air is 340 m/s at emits a sound at a frequency of 30.0 kHz
(a) What is the speed of the bat?
(b) What is the wavelength of the sound that the bat hears15?
Answer:
a) the speed of the bat is 5.02 m/s
b) the wavelength of the sound that the bat hears is 0.011 m
Explanation:
Given the data in the question;
Frequency of sound emitted by a bat f = 30.0 kHz = 30000 Hz
detected frequency by the bat δf = 900 Hz
speed of sound in air c = 340 m/s
Let speed of sound and speed of bat be c and [tex]v_s[/tex] respectively;
Now, frequency of the sound that is coming from the bat towards the wall due to DROPPLER EFFET will be;
f₁ = ( c / ( c - [tex]v_s[/tex] ) )f ----- let this be equ 1
Also, frequency does not change after deflection. The bat becomes an observer as the dropper is shifted because the reflected sound wave is coming towards it;
Hence, Doppler shifted frequency will be;
f₂ = ( (c + [tex]v_s[/tex] ) / c )f₁
from equ 1, f₁ = ( c / ( c - [tex]v_s[/tex] ) )f, so we substitute
f₂ = ( (c + [tex]v_s[/tex] ) / c ) × ( c / ( c - [tex]v_s[/tex] ) )f
f₂ = ( (c + [tex]v_s[/tex] ) / ( c - [tex]v_s[/tex] ) )f
∴ beat frequency will be;
δf = f₂ - f = ( (c + [tex]v_s[/tex] ) / ( c - [tex]v_s[/tex] ) )f - f
δf = ( 2[tex]v_s[/tex] / c - [tex]v_s[/tex] )f
δf = ( 2[tex]v_s[/tex] / c - [tex]v_s[/tex] )f
2f/δf = c - [tex]v_s[/tex] / [tex]v_s[/tex]
2f/δf = c/[tex]v_s[/tex] - [tex]v_s[/tex] / [tex]v_s[/tex]
2f/δf = c/[tex]v_s[/tex] - 1
c/[tex]v_s[/tex] = 2f/δf + 1
[tex]v_s[/tex] = c / (2f/δf + 1)
now, we substitute in our values;
[tex]v_s[/tex] = 340 / ((2×30000 / 900 ) + 1)
[tex]v_s[/tex] = 340 / (66.6666 + 1)
[tex]v_s[/tex] = 340 / 67.6666
[tex]v_s[/tex] = 5.02 m/s
Therefore, the speed of the bat is 5.02 m/s
b) the wavelength of the sound that the bat hears
frequency of reflected wave is;
f₂ = f + δf = 30000 + 900 = 30900 Hz
λ₂ = c / f₂
we substitute
λ₂ = 340 / 30900
λ₂ = 0.011 m
Therefore, the wavelength of the sound that the bat hears is 0.011 m
What is the speed of the wave above of the frequency is 7.0 hertz
Answer:
Umm
Explanation:
Explain how newtons first law applies to the image to the left.
A flying stationary kite is acted on by a force of 9.8 N downward. The wind exerts a force of 45 N at an angle of 50.0 degrees above the horizontal. Find the force that the string exerts on the kite.
Answer:
38 N, 40.0° below the horizontal
Explanation:
Force exerted by an object equals mass times acceleration of that object: F = m ⨉ a. To use this formula, you need to use SI units: Newtons for force, kilograms for mass, and meters per second squared for acceleration.
in which reaction is there a transformation of mass into energy
Answer:
There is a transformation of mass into energy un nuclear fusion
A spacecraft is powered by electricity generated by the heat produced when 23894Pu decays with a half-life of 87.75 y. Engineers predict that the spacecraft will have insufficient power to operate its instruments when the amount of 238 94Pu in its power generators drops below 67 % of the amount it had at launch on September 1, 1977
Required:
In what year will its instruments cease to function?
An object of mass 25kg is falling from the height h=10 m. calculate
a. The total energy of an object at h=10m.
b. Potential energy of the object when it is at h= 4m
c. Kinetic energy of the object when it is at h= 4m
d. What will be the speed of the object when it hits the ground?
Answer:
a=2500J,b=1000K,c=1000J,d=14.142m/s
Explanation:
V²=U²+2gh
V²=0 + 2×10×10=200m/s
a).kinetic energy=(1/2)mv²=(1/2)25×200=2500
potential energy=mgh
p.e=25×10×10=2500J
pe+ke=2500+2500=5KJ
b).mgh=25×10×4=1000J
c). V²=U²+2gh
V²=0+2×10×4
V²=80
kinetic energy=(1/2)mv²
=(1/2)25×80
=1KJ
d). From my first paragraph V²=200
V=√200
V=14.142m/s
When 1.5 kg of mass turns into energy, how much energy is released? Find the equation, substitution, and number with units.
Explanation:
[tex]from \: einstein \: equation : \\ E = m {c}^{2} \\ E = 1.5 \times {(3 \times {10}^{8} )}^{2} \\ E = 1.35 \times {10}^{17} \: joules[/tex]
1. How would the forces from a header with such a light soccer ball cause a concussion? Draw
Two free body diagrams showing how the amount of peak force on the head would compare
to the amount of peak force on a soccer ball in a header that causes a collision.
Answer:
soccer when the ball hits an unprepared player in the head. He also gave examples of concussions occurring when players accidentally knock their heads into other players while attempting to head the ball, particularly if they are attempting to flick the ball backwards.
Explanation:
Heading in soccer can increase your risk of concussions. Over time, repeated subconcussive injuries can also accumulate and cause brain damage.
how hot can the desert get
Answer:
134 f
Explanation:
The hottest temperature ever reliably measured in a desert was 134 degrees F, in Death Valley of the Mojave Desert in 1913.
Temperature. During the day, desert temperatures rise to an average of 38°C (a little over 100°F). At night, desert temperatures fall to an average of -3.9°C (about 25°F). At night, desert temperatures fall to an average of -3.9 degrees celsius (about 25 degrees fahrenheit).
Desert surfaces receive a little more than twice the solar radiation received by humid regions and lose almost twice as much heat at night. Many mean annual temperatures range from 20-25 degrees Celsius. The extreme maximum ranges from 43.5-49 degrees Celsius. Minimum temperatures sometimes drop to -18 degrees Celsius.
Magnesium hydroxide is a common ___?
Answer:
Hello There!!
Explanation:
The answer is=> It is a common component of antacids.
hope this helps,have a great day!!
~Pinky~
PLEASE HELP ME ASAP!!!!
For variables control, a circuit voltage will be measured using a sample of five circuits. The past average voltage for samples of 5 units has been 3.4 volts, and the range has been 1.3 volts.
Required:
What would the upper and lower control limits be for the resulting control charts (average and range)?
Answer:
Average :
UCL = 4.15
LCL = 2.65
Range :
UCL = 2.75
LCL = 0
Explanation:
Given :
Sample size, n = 5
Average, X = 3.4
Range, R = 1.3
A2 for n = 5 ; equals 0.577 ( X chart table)
For the average :
Upper Control Limit (UCL) :
X + A2*R
3.4 + 0.577(1.3) = 4.1501
Lower Control Limit (LCL) :
X - A2*R
3.4 - 0.577(1.3) = 2.6499
FOR the range :
Upper Control Limit (UCL) :
UCL = D4*R
D4 for n = 5 ; equals = 2.114
UCL = 2.114*1.3 = 2.7482
Lower Control Limit (LCL) :
LCL = D3*R
D3 for n = 5 ; equals = 0
LCL = 0 * 1.3 = 0
40 points! Will give brainliest!
Which of the following describes an advantage of AC electricity over DC electricity?
A) AC is found in most low voltage operations.
B) AC is provided as strong, short bursts of electricity.
C) AC can be transported over long distances.
D) AC can be used is small electronic devices.