Answer:
Tuning fork frequency
Room temperature
Explanation:
A ball held 2.0 meters above the floor has 59 joules of potential energy the bald mass is about
Answer:
Mass of ball = 3.0102 Kg.
Explanation:
Potential energy at height h is given by
PE = mgh
where m is the mass of the body
g is the the acceleration due to gravity whose value is 9.8 m/s^2
h is the height from surface level
PE is potential energy
In the problem given h = 2 meters
PE = 59 joules
59 = m*9.8*2
=> m = 59/9.8*2 = 3.0102 Kg
Thus, mass of ball is 3.0102 Kg.
Answer:
3
Explanation:
Top person is wrong
just did lesson
In an area of the deep ocean, hot magma emerges from a crack in Earth’s crust. Which statement describes what will happen to the seawater above the crack as a result of convection?
Water molecules will break apart and flow in a circular pattern.
Water molecules will bond together and rise upward.
The water will become more dense and sink downward.
The water will become less dense and rise upward.
Answer: D
Explanation:
Hot magma erupts from a crack in Earth’s crust with a very high temperature that will surely break the bond of water molecules in contact. As a result of this, The water molecules will become less dense and rise upward.
Therefore, "The water will become less dense and rise upward " is the best statement to describes what will happen to the seawater above the crack as a result of convection.
The water will become less dense and rise upward because less denser materials move upward and more denser comes downward.
What will happen to the seawater above the crack as a result of convection?The seawater will become less dense and rise upward above the crack as a result of convection because water is less denser and the magma that erupts from the crack is denser due to its high viscosity.
So we can conclude that the water will become less dense and rise upward because less denser materials move upward and more denser comes downward.
Learn more about convection here: https://brainly.com/question/9382711
#SPJ2
list the three components of effective communication and give an example of each
Answer:
The three components of effective communication are:
Sending CommunicationReceiving CommunicationFeedbackExplanation:
1) Sending CommunicationOne should think about what he is going to say, structure his message and focus clearly on a the purpose of sending a message. For example if an employer wants to communicate an employee to improve his performance, he should focus hid communication on the results rather than on his failures.
2) Receiving CommunicationThe person on the other end of the communication should be a good listener. For example in the example given, even if the employer effectively communicates his side of the communication, but the employee is not paying his full attention to what his boss is saying, he wouldn't be able to make much of a difference.
3) FeedbackAfter sending and receiving communication, feedback should be given to complete the communication effectively. For example the employer may tell his boss about what he understood from his boss's speech, or what will he do to improve his performance.
What is the inverse tangent of 0.9?
O A. 64.2
O B. 90.0
O C. 42.0
O D. 0.016°
Answer:
i think the aswers is C,
Question 1
A 10 N block is at the bottom of a frictionless incline as shown to the right. How much work must be done against gravity to move it to the top of the incline?
A)600j
B)1000j
C)4800j
D)800j
Answer:
W = 600 J
Explanation:
We have,
According to attached figure,
Height of the inclined plane is 60 m
Force acting on the block is 10 N
It is required to find the work must be done against gravity to move it to the top of the incline. The work done is given by :
W = mgh
or
[tex]W=F\times h\\\\W=10\times 60\\\\W=600\ J[/tex]
So, the work done against the gravity is 600 J.
Which changes would result in a decrease in the gravitational force between two objects? Check all that apply
increasing the distance between the objects
decreasing the distance between the objects
increasing the mass of one of the objects
Dincreasing the mass of both objects
decreasing the mass of one of the objects
decreasing the mass of both objects
We need to find how the gravitational force between two object decreases.
The gravitational force between the objects will decrease by
increasing the distance between the objects
decreasing the mass of one of the objects
decreasing the mass of both objects
Gravitational force is given by
[tex]F=\dfrac{Gm_1m_2}{r^2}[/tex]
where
[tex]G[/tex] = Gravitational constant = [tex]6.674\times 10^{-11}\ \text{Nm}^2/\text{kg}^{2}[/tex]
[tex]m_1[/tex] = Mass of one object
[tex]m_2[/tex] = Mass of other object
[tex]r[/tex] = Distance between the two objects
It can be seen that the gravitational force is proportional to the mass of the objects
[tex]F\propto m_1m_2[/tex]
and inversely proportional to the square of the distance between them
[tex]F\propto \dfrac{1}{r^2}[/tex]
So, if mass of one of the objects decreases then the gravitational force will decrease.
Also, if the distance between the objects increases the gravitational force will decrease.
Learn more:
https://brainly.com/question/21500344
https://brainly.com/question/18961003
Answer:
A, E, F
Explanation:
Right on ED2021
Use the following to answer question 46
I . increase the current
II. use a stronger magnet
III. use thicker wire
IV. reverse the battery
V. add more coils of wire inside the magnet
46. To increase the force with which the wire is pushed when the switch is closed, which of
the following things could be done?
a. I and II only
b. II, III, and IV only
C. II and IV only
d. I, II and V only
47. A group of students had built a homemade motor and were in the process of trying to
test it. When they hooked it up to their battery they found that the wires in their coil got hot, but the coil would not turn. Of the following solutions, which would be their best
course of action to make the motor spin?
a. add more wire to the coil
b. use a stronger magnet
C. use a higher voltage battery
d. plug into an AC source
Answer:
46.) A
47.) A
Explanation:
46.) To increase the force with which the wire is pushed when the switch is closed, the current flowing through the wire should be increased and the stronger magnet should be used.
Remember that
F = BIL
The force is directly proportional to magnetic field B and current I
a. I and II only
47.) Since the wires in their coil got hot, and the coil would not turn, this is overheating which may be as a result of to much voltage supply compare to the length of the length of the coil of wire. To correct this, more wire should be added to the coil.
Which of the following is an example of a device that uses a wheel and axle?
Check all that apply
A. frisbee
B. light bulb
C. doorknob
D. bicycle
(multiple answers)
Spaceship 1 and Spaceship 2 have equal masses of 300kg. They collide. Spaceship 1's final speed is 3 m/s, and Spaceship 2's final speed is 2 m/s in the same direction. What is their combined momentum? A. 600 kg-m/s B. 1,500 kg-m/s C. 1,200 kg-m/s D. 900 kg-m/s
Answer:
B. 1500 kg*m/s
Explanation:
Momentum p = m* v
In any type of collision, the total momentum is preserved!
The total momentum before and the total momentum after the collision is the same. We know the mass and speed after the collision so we can calculate the total momentum.
p1 + p2 =
m1*v1 + m2*v2
m1 = me = 300 kg
v1 = 3 m/s
v2 = 2 m/s
Substitute the given numbers:
300*3 + 300+2
900 + 600
1500 kg*m/s, which is answer B.
formular for calculating resistors in parallel
Answer:
Answer is 1/RT=1/RT1+1/RT2+1/RT3
A velocity vs. time graph is shown. A graph titled Velocity versus Time shows time in seconds on the x axis, numbered 0 to 5, velocity in meters per second on the y axis, numbered 0 to 20. A line starts at the origin and ends at (5, 20). What is the acceleration of the object? 0 m/s2 0.25 m/s2 4 m/s2 8 m/s2
Answer:
C
Explanation:
Given that a line starts at the origin ( 0, 0) and ends at (5, 20)
Where
V1 = 0
V2 = 20
T1 =0
T2 = 5
The slope or gradient of a velocity time graph is the acceleration.
Slope = change in V/ change in t
That is,
Slope = ( V2 - V1 )/ ( T2 - T1 )
Substitutes all the values into the formula
Slope = ( 20 - 0 )/( 5 - 0 )
Slope = 20/5
Slope = 4 m/s^2
Therefore, acceleration of the object is 4m/s^2
Answer:
The first answer is -20m/s
Explanation:
On EDGE 2021
Least
C
B
A
Greatest
i dont know if this is the same question as yours lol
A 10 N block is at the bottom of a frictionless incline as shown to the right. How much work must be done against gravity to move it to the top of the incline?
600j
1000j
4800j
800j
Explanation:
We have,
According to attached figure, the height of the inclined plane is 60 m and force acting on the block is 10 N. It is required to find the work must be done against gravity to move it to the top of the incline. The work done is given by :
W = mgh
or
[tex]W=F\times h\\\\W=10\times 60\\\\W=600\ J[/tex]
Hence, the correct option is (A) "600 J".
Which vector is the sum of the vectors shown below?
What is cos(6)?
A. 0.99
B. 0.60
C. 0.10
D. 0.06
Answer:
A. 0.99 :)
Explanation:
Question 14 of 30
1 Point
Which of the following ideas was proposed by the ancient Greeks about 2500
years ago?
O A. Atoms consist of positive and negative charges.
O B. Atoms are indivisible units of matter.
OC. All atoms are alike.
O D. Atoms are composed of protons, neutrons, and electrons.
SUBMIT
Answer: a.
Explanation: i have done this before .. hope this helps (⌐■_■)
Answer:
B
Explanation:
HACE 2500 AÑOS NO SE CONOCÍAN LAS CARGAS ATÓMICAS.
Which is a resource that the National Park Service manages?
A. memorials
B. wildlife refuges
C. ecosystems
D. endangered species
Answer:
Which is a resource that the National Park Service manages?
A. memorials
B. wildlife refuges
Answer:
wildlife refuges
Explanation:
Anyone know the answer to this, would kindly appreciate it
Answer:
The found value of r is:
r = 94.7
Explanation:
We know that
cosθ = Base / Hypotenuse
θ is the always the angle between base and hypotenuse
In this right angles triangle, the angle θ is given 63°.
Which means that the Base is 43 and the hypotenuse is r
Base = 43
Hypotenuse = r
Substitute θ=63°, Base = 43 and hypotenuse = r in the formula of cosθ mentioned above:
cos 63° = 43/r
Rearrange
r = 43/cos63°
r = 43/0.454
r= 94.7
A circuit has a 10 Ω resistor connected to a 1.5 V dry cell. What is the current that can flow in the circuit?
Here is the highly detailed, arcane, complex, technical form of Ohm's Law that is needed in order to answer this question ===> I = V / R .
Current = (voltage) / (resistance)
Current = (1.5 V) / (10 Ω)
Current = 0.15 Ampere
Using ohms law
[tex]\boxed{\sf \dfrac{V}{I}=R}[/tex]
[tex]\\ \sf\longmapsto I=\dfrac{V}{R}[/tex]
[tex]\\ \sf\longmapsto I=\dfrac{1.5}{10}[/tex]
[tex]\\ \sf\longmapsto I=0.15A[/tex]
Circuit questions. Plz help. Only answer is ok
physics question please help
ASAP please! Three positive charges are arranged as shown in the diagram. Three charges at the corners of an isosceles triangle. The two charges at the base are +5 microcoulombs and +9 microcoulombs and are separated by .32 m. The triangle is .42 m tall up to a charge +3 microcoulombs. The other two sides of the triagle are both .45 m. What is the magnitude and direction of the net electrical force acting on the +3 µC charge? magnitude: 1.75 N direction: 6.2° north of east magnitude: 1.75 N direction: 6.2° south of east magnitude: 1.86 N direction: 21° north of east magnitude: 1.86 N direction: 21° south of east
Answer:
Fn = 1,78 [N]
β = 6,4⁰ north-east direction
Explanation:
As all charges are positive, forces between electric charges located in the cornes of the base of the triangle and the charge located in the top of the isoceles triangle, are repulsion forces. The east-west direction will depend on where the biggest charge is located, if Q₁ = 9 microC, is in the left end of the triangle base then force on charge Q₃ = 3 microC will have direction north-east, if the above mention configuration change (that means Q₁ is in the right end of the triangle base) then the force will have north-west direction. As in the answer solution, 1,75 [N] direction north-east is offer, we will choose the first configuration. According to that:
K = 1/4*π*ε₀ K = 8,98*10⁹ [N*m²/C²]
The angles in the base of the triangle are equals (we call it α )
sinα = 0,42/045 = 0,93
α = 69⁰
cosα = 0,356
And Q₃ = 3 mC = 3*10⁻⁶ C
Q₁ = 9 mC = 9*10⁻⁶ C
Q₂ = 5 mC = 5*10⁻⁶ C
F₁ [Q₁,Q₃] = K*Q₁*Q₃/d² ⇒F [Q₁,Q₃] = 8,98*10⁻⁹ * 9*10⁻⁶ * 3*10⁻⁶/(0,45)²[N]
F₁ [Q₁,Q₃] = 1,2 [N] direction along the side of the triangle therefore
its components are:
F₁ₓ = F₁* cosα ⇒ F₁ₓ = 1,2 * 0,356
F₁ₓ = 0,43 [N]
F₁y = F₁ *sinα ⇒ F₁y = 1,2 * 0,93
F₁y = 1,16 [N]
Now
F₂ [Q₂,Q₃] = K*Q₂*Q₃/d² ⇒F [Q₂,Q₃] = 8,98*10⁻⁹ * 5*10⁻⁶ * 3*10⁻⁶/(0,45)²[N]
F₂ = 0,67 [N]
F₂ₓ = F₂* cosα ⇒ F₂ₓ = 0,67*0,356
F₂ₓ = 0,24 [N]
F₂y = F₂*sinα ⇒ F₂y = 0,67*0,93
F₂y = 0,62 [N]
We must remember F₁ and F₂ are repulsion forces, then components over y-axis have the same sense (we must add then) and components over x-axis have to be subtracted, in this case, the sense is determine by major force component (to the right) according to this:
Fy = F₁y * F₂y = 1,16 + 0,62
Fy = 1,78 [N]
And
Fₓ = F₁ₓ - F₂ₓ = 0,43 - 0,24
Fₓ = 0,19
Net force module is:
Fn = √ (1,78)² + (0,19)²
Fn = 1,79 [N]
Having an angle respect the y-axis:
tan β = 0,19/1,78 ⇒ tan β = 0,11 and from tan tables
β = 6,4⁰ north-west direction
Answer: magnitude: 1.75 N ; direction: 6.2° north of east
Explanation:
It's right
Tectonic plates move on which layers of the Earth? a. Crust and upper mantle b. Crust and mantle c. Upper and lower mantle d. Crust, mantle, outer core
Answer:
a. crust and upper mantle
Explanation:
Answer:
a. crust and upper mantle
Explanation:
How does population density differ from population size?
а. Population size takes all organisms into account while population density only takes specific age
groups of the population into account
b. Population size is the total number of organisms, while population density is the total number of
organisms within a given area
C Population size is the total number of organisms within a given area, while population density is the
total number of organisms of a specific age
d. Population size is the total number of organisms of all species, while population density is the total
number of organisms of a specific species
Answer: B
Explanation:
Population size focuses on the size of the population. That is, the total number of organisms in a population.
While population density focuses on the density of the population. That is, mean number of organisms per unit area or volume.
Therefore, Population size is the total number of organisms, while population density is the total number of
organisms within a given area
The formation of a product in the reaction is based on what
Answer:
c
Explanation:
there is formation of products when t reactants react or collied
If for every increase of 1 for x, y increases by 2, x and y have an) -
relationship
O
A. negative
O
B. linear
O
C. inverse
O
D. circular
SUBMIT
Answer:
The correct option is B.
B) Linear
Explanation:
Suppose initially the value of x is 0, for which y is also 0. When x is increased to 1, the value of y becomes 2. If the value of x is increase to 2, the value of y becomes 4. Similarly, if x is increases to 3,4, and 5, the corresponding values of y we get are 6,8 and 10.
From the above data, we can model that the above relation is:
y = 2x
I've attached the graph of this function below. We can clearly see from the graph that the relation between x and y is linear.
Which of the following is not true about centripetal force? Check all that
apply.
A. It's the same as centrifugal force.
B. It's also called an inward force.
C. Centripetal force keeps a car on the road going around a curve.
D. Without centripetal force, an object would continue in a straight
line.
E. Centripetal force is the same as gravity.
multiple answer question
Answer:
A, B Y E
Explanation:
The following is not true about Centripetal Force.
It's the same as centrifugal forceCentripetal force is the same as gravityWhat is Centripetal Force?Centripetal Force is the force that makes a body to move in a curved path. The direction of the force to the motion of the body is orthogonal and it is inward towards the fixed point of the center of rotation.
Therefore, following is not true about Centripetal Force.
It's the same as centrifugal force.Centripetal force is the same as gravity.Learn more about Centripetal Force from the link below.
https://brainly.com/question/20905151
How may the desire for a perfect lawn related to environmental pollution
Answer:
Lawns are extremely costly in many ways, including dollars spent on them, the deadly ... Using lawn equipment also significantly adds to noise pollution. ... to all of the environmental damages, including water pollution, caused by fracking. ... ONE's ambition is to remain unbiased and to provide a good
Explanation:
Answer:
The gases from the lawn mower to mow the grass, weed killer toxicity affects, too much of the seeds to help grow your grass can actually harm your grass, etc.
Explanation:
As hotter material _______, ________material sinks. a. Sinks, colder b. Rises, warmer c. Rises, colder d. Sinks, warmer
Answer:
C
Explanation:
Hot air rises because when you heat air (or any other gas for that matter), it expands. When the air expands, it becomes less dense than the air around it. The less dense hot air then floats in the more dense cold air much like wood floats on water because wood is less dense than water.
As hotter material gets colder it will sinks down. In the hotter state the molecules gets energetic and gets far apart making them free to rise in the air. Thus option a is correct.
What is sinking ?Hot air is less dense than cold air, which is why hot air rises and cold air descends. The earth's weather is controlled by hot and cold air currents. The planet is heated primarily by the sun, which also generates the planet's hot and cold air energy systems.
Since warm air currents originate over oceans, they frequently bring rain. Tropical storms and hurricanes develop at sea and eventually travel near land for this reason.
As hot air from the earth's surface rises, it rapidly turns into cold air as it approaches space. As hot air cools, it descends back to the earth's surface, where it is warmed by the ocean before rising once more. An example of this is a convection current. Thus, option a is correct.
Find more on colder air :
https://brainly.com/question/25341433
#SPJ2
A student is pushing a box across the room. To push the box three times farther, the student needs to do how much work?
Answer:
Removing some of the books reduced the mass of the box, and less force was needed to push it across the floor.
A 4.0 kg block is resting on a rough horizontal table. The coefficient of static friction us is 0.60. The static friction between the block and the table before any attempted motion is to start is N. (round to the nearest integer)
Answer: 24 N
Explanation:
Given that the
Mass m = 4 kg
Coefficient of friction (μ) = 0.60
To calculate the static friction between the block and the table before any attempted motion, you will use the formula; F = (μ)N
Where
F = static friction
N = normal reaction = mg
g = acceleration due to gravity = 9.8 m/^2
Substitutes m, g and (μ) into the formula
F = 0.6 × 4 × 9.8
F = 23.52 N
Therefore, the static friction between the block and the table before any attempted motion is 24 N approximately.
The static friction between the block and the table before any attempted motion is to start equals 23.52 Newton.
Given the following data:
Mass of block = 4.0 kgCoefficient of static friction = 0.60.To determine the static friction between the block and the table before any attempted motion is to start:
Mathematically, the force of static friction is given by the formula;
[tex]F_s = uF_n[/tex] ...equation 1.
Where;
[tex]F_s[/tex] represents the force of static friction.μ represents the coefficient of friction.[tex]F_n[/tex] represents the normal force.But, [tex]F_n = mg[/tex]
[tex]F_s = umg[/tex] ...equation 2.
Substituting the given parameters into eqn. 2, we have;
[tex]F_s = 0.60 \times 4 \times 9.8\\\\F_s = 23.52\; Newton[/tex]
Force of static friction = 23.52 Newton
Read more: https://brainly.com/question/13754413