An ideal Rankine cycle is a vapor power cycle that is used to convert thermal energy into work. It consists of four main components: the pump, the boiler, the turbine, and the condenser. Water is used as the working fluid in an ideal Rankine cycle.
Steam enters the turbine at 20 MPa and 400°C and exits as a wet vapor. The pressure in the condenser is 10 kPa. A T-s diagram can be sketched for this process. Three assumptions made for the ideal Rankine cycle are: the process is steady-state, no work is done on or by the pump, and the turbine operates adiabatically.
Dry fraction of the steam leaving the turbine: The dryness fraction of the steam leaving the turbine can be calculated using the steam tables. Assuming the steam is ideal, the entropy of the steam entering the turbine (s1) can be determined from the steam tables, which will be the same as the entropy of the steam leaving the turbine (s2).
To know more about convert visit:
https://brainly.com/question/33168599
#SPJ11
1. The purpose of a riser is to A. deliver molten metal in to the mold cavity. B. act as a reservoir for the molten metal. C. feed the molten metal to the casting in order to compensate for the shrinkage. D. deliver the molten metal from pouring basin to gate. ( ) 2. A two high rolling mill consists of two rolls which rotate A. at the same speed and in the same direction B. at the same speed but in opposite direction C. at different speeds and in the same direction D. at different speeds and in the opposite direction. ( 13. A common characteristic of sand casting and investment casting is : A. Both may be used to produce small castings B. Both produce castings of great dimensional accuracy C. Both make use of wooden patterns D. Both make use of re-useable molds ( ) 4. Metal patterns are used for A. small castings B. large castings C. complicated castings D. large scale production of castings ( ) 5. Which of the below can determine if the residual stress in the workpiece after rolling is compression or tension? A. Speed of rolling B. The roll diameter and reduction ratio C. Type of metal being rolled D. None of the above
The purpose of a riser is to provide an additional source of molten metal to compensate for the shrinkage of the casting. A detailed explanation is given below:Risers, often known as feeders, are reservoirs of molten metal that are designed to provide the necessary additional molten metal to compensate for the shrinkage as the casting cools.
They are created with the same materials as the casting and are removed from the finished product during the cleaning process.2. The rolls of a two-high rolling mill rotate at the same speed but in opposite directions. A detailed explanation is given below:A two-high rolling mill is a device that has two rolls that rotate at the same speed but in opposite directions.
The material being rolled is pulled between the two rolls, which reduce the thickness of the material. Because both rolls rotate at the same speed but in opposite directions, the material is rolled in a single direction.3. Both sand casting and investment casting have a common characteristic of using re-useable molds. A detailed explanation is given below:Both sand casting and investment casting have a common characteristic of using re-useable molds.
To know more about metal visit:
brainly.com/question/33285017
#SPJ11
A metallic resistance strain gauge as resistance of 120 μ. Its gauge factor is 2. It is fixed on a metallic test surface. If the yield stress on the material is 200 MN/m² and the young's modulus of e elasticity is 8×104 MN/m². Determine the change In the resistance of the gauge If the gauge is loaded up to yield point stress. [E 6.5]
A strain gauge is a metal wire of known cross-sectional area fixed on the test material surface, which undergoes strain when the material undergoes stress. The gauge factor is a gauge sensitivity parameter.
Therefore, if the gauge factor is known, it is possible to calculate the stress produced on the test material when the gauge is stressed. The gauge factor is determined experimentally and is the proportionality constant between the strain produced and the change in resistance of the gauge.
Resistance of the gauge is given by, Resistance, R = 120 μGauge factor,
G = 2Young’s modulus,
E = 8 × 10⁴ MN/m²Yield stress,
σy = 200 MN/m²Change in resistance of the gauge:
ΔR = RGσy/EΔR = (2)(120 μ)(200 MN/m²)/(8 × 10⁴ MN/m²)ΔR = 0.006. Therefore, the change in the resistance of the gauge is 0.006 μ.
To know more about metal visit:
https://brainly.com/question/29404080
#SPJ11
The volumetric analysis of the product of combustion on a dry basis for the oxidation of octane (C8H18) in air is 9.18% CO2, 0.23% CO and 7.48% O2. Write the combustion equation and determine the percent excess or deficiency of air in the combustion process.
Use Mass Balance
Please complete the answer with correct solution
The percent excess or deficiency of air in the combustion process is 0.57% excess air.
For the mass balance equation, we have,Mass of unburned oxygen = (12.5 - 7.48/100 × 12.5) × 32 × x / 100Mass of air = 77/100 × x Mass of CO₂ = 4.04 g
Mass of CO = 0.064 g
Mass of O₂= 2.39 g + (12.5 - 7.48/100 × 12.5) × 32 × x / 100
Mass of H₂O = 100 - (mass of CO₂ + mass of CO + mass of O₂ + mass of unburned oxygen)
Now, we will substitute all these values into the mass balance equation
. That is,Mass of octane + 77/100 × x = 4.04 + 0.064 + 2.39 + (12.5 - 7.48/100 × 12.5) × 32 × x / 100 + Mass of H₂O
6.494 g/100 g of the product of the combustion = mass of CO₂ + mass of CO + mass of H₂O
Mass of H₂O = 100 - 6.494 = 93.506 g/100 g of the product of the combustion
By substituting all these values, the equation becomes,
114.17 + 77/100 × x = 6.494 + 0.064 + 2.39 + (12.5 - 7.48/100 × 12.5) × 32 × x / 100 + 93.506
Solving for x, we get,x = 162.27 g
Thus, the mass of air required for the combustion of 114.17 g of octane is 162.27 g.
Hence, the percent excess or deficiency of air can be calculated as, Percent excess air = (actual air - theoretical air) / theoretical air × 100= (162.27 - 161.35) / 161.35 × 100= 0.57%
Learn more about the mass at
https://brainly.com/question/19581668
#SPJ11
It is required to transmit torque 537 N.m of from shaft 6 cm in diameter to a gear by a sunk key of length 70 mm. permissible shear stress is 60 MN/m. and the crushing stress is 120MN/m². Find the dimension of the key.
It is required to transmit torque 537 N.m of from shaft 6 cm in diameter to a gear by a sunk key of length 70 mm. The permissible shear stress is 60 MN/m. and the crushing stress is 120MN/m². Find the dimension of the key.
The dimension of the key can be calculated using the following formulae.
Torque, T = 537 N-m diameter of shaft, D = 6 cm Shear stress, τ = 60 MN/m Crushing stress, σc = 120 MN/m²Length of the key, L = 70 mm Key width, b = ?.
Radius of shaft, r = D/2 = 6/2 = 3 cm.
Let the length of the key be 'L' and the width of the key be 'b'.
Also, let 'x' be the distance of the centre of gravity of the key from the top of the shaft. Let 'P' be the axial force due to the key on the shaft.
Now, we can write the equation for the torque transmission by key,T = P×x = (τ/2)×L×b×x/L+ (σc/2)×b×L×(D-x)/LAlso, the area of the key, A = b×L.
Therefore, the shear force acting on the key is,Fs = T/r = (2T/D) = (2×537)/(3×10⁻²) = 3.58×10⁵ N.
From the formula for shear stress,τ = Fs/A.
Therefore, A = Fs/τ= 3.58×10⁵/60 × 10⁶= 0.00597 m².
Hence, A = b×L= 5.97×10⁻³ m²L/b = A/b² = 0.00597/b².
From the formula for crushing stress,σc = P/A= P/(L×b).
Therefore, P = σc×L×b= 120×10⁶×L×b.
Therefore, T = P×x = σc×L×b×x/L+ τ/2×b×(D-x).
Therefore, 537 = 120×10⁶×L×b×x/L+ 30×10⁶×b×(3-x).
Therefore, 179 = 40×10⁶×L×x/b² + 10×10⁶×(3-x).
Therefore, 179b² + 10×10⁶b(3-x) - 40×10⁶Lx = 0.
Since the key dimensions should be small, we can take Lx = 0 and solve for b.
Therefore, 179b² + 30×10⁶b - 0 = 0.
Solving the quadratic equation, we get the key width, b = 46.9 mm (approx).
Therefore, the dimension of the key is 70 mm × 46.9 mm (length × width).
Hence, the dimension of the key is 70 mm × 46.9 mm.
To know more about diameter visit:
https://brainly.com/question/32968193
#SPJ11
You are an environmental engineer working for a manufacturing company that makes computer components. In the process your plant creates toxic wastes, primarily as heavy metals. Part of your job is to oversee the testing of the effuluent from your plant, signing the test results to attest to their accuracy and supplying them to the city. The allowable limit of the chemicals disposed is less when compared to the national chemical standard limits permitted. But you are very concerned about the fact that what will the smaller concentrations amount to. You also found out that even with reduced limits the heavy metals disposed are highly dangerous. You have to prepare a report a report for the same. a. Interpret with the help of two NSPE codes in this case b. develop what must be written details that should be included in the report
Two NSPE codes in this case can be: Engineers shall hold paramount the safety, health, and welfare of the public and the protection of the environment (NSPE Code of Ethics 2007, III.1.).
Engineers shall avoid deceptive acts that falsify their qualifications (NSPE Code of Ethics 2007, III.4.).b. The report should include the following details: The report should present the information that indicates that despite the lower levels of toxic waste that the plant produces, the heavy metals it emits are still highly dangerous.
The report should also discuss the implications of the heavy metals and what they can cause. The report should provide a complete review of the situation, including how it came to light, the testing process and results, and what steps have been taken to fix the problem.
To know more about NSPE codes visit:
https://brainly.com/question/30641935
#SPJ11
e. A 4-pole turbo-generator rated at 20MVA, 13.2kV, 50Hz has an inertia constant of H=8.5kW- s/kVA. Determine; i. The kinetic energy stored in the rotor at synchronous speed. ii. The acceleration if the input less the rotational losses is 17300kW and the electric power developed is 14200kW iii. The change in torque angle in that period and the rpm at the end of 10 cycles
Given data,Number of poles, P= 4Power rating, P = 20 MVA (Mega Volt Ampere)Rated voltage, V = 13.2 kV (kilo Volt)Frequency, f = 50 HzInertia constant, H = 8.5 kW- s/kVA(a) Kinetic energy stored in the rotor at synchronous speed:Synchronous speed (Ns) = 120f/P
The kinetic energy stored in the rotor (E) = 1/2 * Inertia constant * (Power rating in kVA)^2 / (Synchronous speed in rpm)Kinetic energy stored in the rotor at synchronous speedE = 1/2 * H * (P × 1000)^2 / NsE = 1/2 * 8.5 * (20,000)^2 / 1500E = 1,133,333.33 J× 1000 / 1500)α = 1.71 rad/s^2(c) Change in torque angle in that period and the RPM at the end of 10 cycles:Initial torque angle = δ1 = cos⁻¹ (Pm / (V × Ia)) = cos⁻¹ (17300 / (13200 × 1557.73)) = 1.5566 radTime period of 10 cycles, T = 10 / f = 0.2 sAt the end of 10 cycles, the final torque angle = δ2 = cos⁻¹ (Pm / (V × Ia)) = cos⁻¹ ((Pm – J × α × N × δ1) / (V × Ia))δ2 = cos⁻¹ ((423.36 – 8.5 × 20,000 × 1.71 × 1500 × 1.5566) / (13200 × 1557.73))δ2 = 1.853 radChange in torque angle, Δδ = δ2 – δ1Δδ = 1.853 – 1.5566Δδ = 0.296 radRPM at the end of 10 cycles, N1 = (P × 1000 × 60) / (Poles × f)N1 = (20,000 × 60) / (4 × 50)N1 = 2400 rpmAt the end of 10 cycles, the RPM will be given by,N2 = N1 – (α × δ1 × 30 / π)²N2 = 2400 – (1.71 × 1.5566 × 30 / π)²N2 = 2299.15 rpm
Therefore, The kinetic energy stored in the rotor at synchronous speed is 1,133,333.33J. The acceleration is 1.71 rad/s². The change in torque angle in that period is 0.296rad and the RPM at the end of 10 cycles is 2299.15 rpm.
To know more about Number visit :
https://brainly.com/question/3589540
#SPJ11
A gentleman used a spring scale to measure his luggage weight 3 times in different time under fixed condition and found the results were 42.1, 41.8 and 42.5lbf, respectively. From the above results, estimate the nearest first order uncertainty? 1.51 0.35 All solutions are not correct 0.87
The nearest first-order uncertainty is approximately 0.27 lbf. The correct answer is 0.35. The correct answer is option(b).
The nearest first-order uncertainty can be estimated by calculating the standard deviation. Standard deviation is a measure of the amount of variation or dispersion of a set of values.
Given measurements are as follows:42.1, 41.8, 42.5lbfThe formula to calculate the standard deviation is:
Standard deviation formulaσ=√((Σ(xi−x¯)2)/(n−1))
Where xi is the measurement value, x¯ is the mean value, and n is the number of observations.
Let's calculate the mean first.
Mean= (42.1 + 41.8 + 42.5)/3= 126.4/3= 42.13333lbf
Now let's calculate the standard deviation.
σ=√(((42.1-42.1333)2+(41.8-42.1333)2+(42.5-42.1333)2)/(3-1))
σ=√((0.01778+0.12216+0.13689)/2)
σ=√(0.14183/2)
σ=√0.070915
σ= 0.2664
Therefore, the nearest first-order uncertainty is approximately 0.27 lbf. The correct answer is 0.35.
To know more about Standard deviation refer to:
https://brainly.com/question/31974941
#SPJ11
A series of weighing of a sample of metal powder are made with the following results: Weight of a sample, grams: 2.020 2.021 2.021 2.019 2.019 2.018 2.021 2.018 2.021 2.017 2.017 2.020 2.016 2.019 2.020 Compute average and standard deviation for the weighing.
To compute the average and standard deviation for the weighing of the metal powder sample, follow these steps: Calculate the average (mean) weight:
Add up all the weights and divide by the total number of measurements. Average weight = (2.020 + 2.021 + 2.021 + 2.019 + 2.019 + 2.018 + 2.021 + 2.018 + 2.021 + 2.017 + 2.017 + 2.020 + 2.016 + 2.019 + 2.020) / 15
Calculate the standard deviation: a. Subtract the average weight from each individual weight to get the deviation.
b. Square each deviation.
c. Sum all the squared deviations.
d. Divide the sum by (n-1), where n is the total number of measurements.
e. Take the square root of the result.
Let's calculate the average and standard deviation:
Average weight = (2.020 + 2.021 + 2.021 + 2.019 + 2.019 + 2.018 + 2.021 + 2.018 + 2.021 + 2.017 + 2.017 + 2.020 + 2.016 + 2.019 + 2.020) / 15
= 30.307 / 15
≈ 2.020 grams (rounded to three decimal places)
Standard deviation = √[(Σ(x - μ)²) / (n - 1)]
= √[(0.000² + 0.001² + 0.001² + (-0.001)² + (-0.001)² + (-0.002)² + 0.001² + (-0.002)² + 0.001² + (-0.003)² + (-0.003)² + 0.000² + (-0.004)² + (-0.001)² + 0.000²) / (15 - 1)]
Performing the calculations and taking the square root will give you the standard deviation for the weighing.
Learn more about deviation here
https://brainly.com/question/30583997
#SPJ11
Design a three stepped distance protection for the protection of an EHV transmission line. Explain / label all the steps and constraints using circuit diagram(s) as well. Put together your proposed scheme considering the trip contacts configuration of the circuit breaker(s).
Distance protection is a type of protection scheme used in power system transmission line protection. It provides good selectivity and sensitivity in identifying the faulted section of the line.
The main concept of distance protection is to compare the voltage and current of the protected line and calculate the distance to the fault. This protection is widely used in Extra High Voltage (EHV) transmission lines. Design of three-stepped distance protection: Three-stepped distance protection for the EHV transmission line can be designed using the following steps:
Step 1: Zone 1 protection For the first step, we use the distance relay to provide Zone 1 protection. This relay is located at the beginning of the transmission line, and its reach is set to cover the full length of the line plus the length of the adjacent feeder. The relay uses the phase-to-phase voltage (Vab, Vbc, Vca) and the three-phase current (Ia, Ib, Ic) to measure the impedance of the line. If the calculated impedance falls below a set threshold, the relay trips the circuit breaker. The circuit diagram of Zone 1 protection is as follows:
Step 2: Zone 2 protection For the second step, we use the distance relay to provide Zone 2 protection. This relay is located at a distance from the substation, and its reach is set to cover the full length of the transmission line plus a margin. The relay uses the phase-to-phase voltage (Vab, Vbc, Vca) and the three-phase current (Ia, Ib, Ic) to measure the impedance of the line. If the calculated impedance falls below a set threshold, the relay trips the circuit breaker. The circuit diagram of Zone 2 protection is as follows:
Step 3: Backup protection For the third step, we use the overcurrent relay to provide backup protection. This relay is located at the substation and uses the current of the transmission line to measure the fault current. If the fault current exceeds a set threshold, the relay trips the circuit breaker. The circuit diagram of the backup protection is as follows:
Constraints: There are some constraints that we need to consider while designing three-stepped distance protection for the EHV transmission line. These are as follows:• The reach of each zone should be set appropriately to avoid false tripping and ensure proper selectivity.• The time delay of each zone should be coordinated to avoid overreach.• The CT ratio and PT ratio should be chosen such that the relay operates correctly.• The trip contact configuration of the circuit breaker should be considered while designing the protection scheme.
To know more about Distance protection visit:
https://brainly.com/question/31914334
#SPJ11
Please elaborate more, upvote will be kindly given
Differentiate between force and natural convection. Explain briefly why the convective heat transfer coefficient in forced convection is usually higher than that in natural convection. (5 marks)
Force convection is a type of convection that happens when a fluid is forced to move over a surface or in a tube. On the other hand.
Natural convection is a type of convection that occurs when a fluid is heated, causing it to expand and rise, producing a convection current that circulates the fluid. Both natural and forced convection are used for heat transfer, but there are some differences between them.In natural convection.
The convective heat transfer coefficient is lower than that in forced convection. The reason is that in natural convection, the motion of the fluid is caused by buoyancy forces, which are weaker than the forces generated by forced convection.
To know more about convection visit:
https://brainly.com/question/4138428
#SPJ11
For an Iron-Carbon alloy, what is the lowest temperature at which liquid of any kind will form?
Find the mass fractions of α ferrite and cementite in a sample of 100% pearlite.
Identify which pro-eutectoid phase would be present in an iron–carbon alloy in which the temperature is 600°C and mass fractions of total ferrite and total cementite are as follows: Total % ferrite = 79% | Total cementite = 21%
Find the mass fractions of pro-eutectoid ferrite and pearlite that form in steel with 0.30% wt Carbon:
What percentage of an iron-carbon alloy at 300°C would be pearlite if a 500 gram sample contained 3.8 grams of Carbon and 496.2 grams of Iron?
The lowest temperature at which liquid of any kind will form in an Iron-Carbon alloy is the liquidus temperature, which depends on the carbon content. For a hypoeutectic alloy, liquid will start to form at the eutectic temperature of around 1147°C. The mass fractions of α ferrite and cementite in 100% pearlite are 0% and 100%, respectively. At 600°C with mass fractions of 79% ferrite and 21% cementite, the pro-eutectoid phase present would be cementite. For a steel with 0.30% wt carbon, the mass fractions of pro-eutectoid ferrite and pearlite are 0% and 100%, respectively. At 300°C, if a 500 gram iron-carbon alloy contains 3.8 grams of carbon and 496.2 grams of iron, the percentage of pearlite would depend on the alloy's composition and the phase diagram.
In an Iron-Carbon alloy, the lowest temperature at which liquid of any kind will form is the liquidus temperature. This temperature varies depending on the carbon content of the alloy. In a hypoeutectic alloy (carbon content less than the eutectic composition), the liquidus temperature is the eutectic temperature, which is approximately 1147°C. At temperatures below the liquidus temperature, the alloy exists in a solid state.
In a sample of 100% pearlite, which is a lamellar structure consisting of alternating layers of α ferrite and cementite, the mass fraction of α ferrite is 0% and the mass fraction of cementite is 100%. This is because pearlite is composed entirely of cementite.
At a temperature of 600°C and with mass fractions of total ferrite at 79% and total cementite at 21%, the pro-eutectoid phase present in the iron-carbon alloy would be cementite. This is determined by comparing the mass fractions to the phase diagram for the specific alloy composition.
For a steel with 0.30% wt carbon, the mass fraction of pro-eutectoid ferrite is 0% and the mass fraction of pearlite is 100%. This is because the steel composition lies in the hypereutectoid range, where pearlite forms as the pro-eutectoid phase.
To determine the percentage of pearlite at 300°C in an iron-carbon alloy sample containing 3.8 grams of carbon and 496.2 grams of iron, additional information is required. The percentage of pearlite formation depends on the alloy composition and the phase diagram, which provides the equilibrium phases at different temperatures and compositions. Without knowing the specific composition of the alloy, it is not possible to determine the exact percentage of pearlite at 300°C.
To learn more about alloy click here: brainly.com/question/1759694
#SPJ11
The lowest temperature at which liquid of any kind will form in an Iron-Carbon alloy is the liquidus temperature, which depends on the carbon content. For a hypoeutectic alloy, liquid will start to form at the eutectic temperature of around 1147°C.
The mass fractions of α ferrite and cementite in 100% pearlite are 0% and 100%, respectively. At 600°C with mass fractions of 79% ferrite and 21% cementite, the pro-eutectoid phase present would be cementite. For a steel with 0.30% wt carbon,
the mass fractions of pro-eutectoid ferrite and pearlite are 0% and 100%, respectively. At 300°C, if a 500 gram iron-carbon alloy contains 3.8 grams of carbon and 496.2 grams of iron, the percentage of pearlite would depend on the alloy's composition and the phase diagram.
In an Iron-Carbon alloy, the lowest temperature at which liquid of any kind will form is the liquidus temperature. This temperature varies depending on the carbon content of the alloy.
In a hypoeutectic alloy (carbon content less than the eutectic composition), the liquidus temperature is the eutectic temperature, which is approximately 1147°C. At temperatures below the liquidus temperature, the alloy exists in a solid state.
In a sample of 100% pearlite, which is a lamellar structure consisting of alternating layers of α ferrite and cementite, the mass fraction of α ferrite is 0% and the mass fraction of cementite is 100%. This is because pearlite is composed entirely of cementite.
At a temperature of 600°C and with mass fractions of total ferrite at 79% and total cementite at 21%, the pro-eutectoid phase present in the iron-carbon alloy would be cementite. This is determined by comparing the mass fractions to the phase diagram for the specific alloy composition.
For a steel with 0.30% wt carbon, the mass fraction of pro-eutectoid ferrite is 0% and the mass fraction of pearlite is 100%. This is because the steel composition lies in the hypereutectoid range, where pearlite forms as the pro-eutectoid phase.
To determine the percentage of pearlite at 300°C in an iron-carbon alloy sample containing 3.8 grams of carbon and 496.2 grams of iron, additional information is required. The percentage of pearlite formation depends on the alloy composition and the phase diagram,
which provides the equilibrium phases at different temperatures and compositions. Without knowing the specific composition of the alloy, it is not possible to determine the exact percentage of pearlite at 300°C.
To know more about diagram click here
brainly.com/question/24255872
#SPJ11
a) Power is defined as: i) The amount of work performed per unit of distance. ii) Force per unit of time. iii) The amount of work performed per unit of time. iv) Normal force x coefficient of friction.
The correct definition of power is the amount of work performed per unit of time. It is usually represented in watts, which is equal to joules per second.
Therefore, power can be calculated using the formula: Power = Work/Time.
The amount of work performed per unit of distance is not a correct definition of power. This is because work and distance are not directly proportional. Work is a function of both force and distance.
Force per unit of time is not a correct definition of power. This is because force alone cannot measure the amount of work done. Work is a function of both force and distance.
Normal force x coefficient of friction is not a correct definition of power. This is because it is a formula for calculating the force of friction, which is a different concept from power.
In conclusion, the correct definition of power is option iii) the amount of work performed per unit of time.
To know more about power visit:
https://brainly.com/question/29575208
#SPJ11
45. A shaft of 1.0 inch diameter has a single dise weighing 75 lb mounted midway between two bearings 20 inches apurt . Neglecting the weight of the shaft. calculate the lowest entical speed in rpm. Note: Modulus of elasticity is 30 x 10% pri C. 1709 rpm A 2038 B. 2540 rpm D. 2094 rpm FER
Hence, the correct option is (B) 2038 rpm.
Given that, A shaft of 1.0-inch diameter has a single disc weighing 75 lb mounted midway between two bearings 20 inches apart, and the Modulus of elasticity is 30 × 106 psi.
The lowest critical speed (N) of a shaft is given by the relation:
N = (0.00305/2π) (K/δ) (α/E) (60/2L)
Where, K = stiffness of the shaft (lb/in)δ = mass per unit length of the shaft (lb-s2/in)α = constant
E = modulus of elasticity (psi)L = span (in)
Given, Diameter (d) of the shaft = 1.0 inch
Radius of the shaft = r = d/2 = 1/2 = 0.5 inch
Midway between two bearings,
Distance between two bearings = 20 inches
Length of the shaft = L = 20/2 = 10 inches
Weight of the disc = W = 75 lb
Density of the material of the shaft = 0 (neglecting the weight of the shaft)
Modulus of elasticity (E) = 30 × 106 psi
Calculation of α:
For the disc, α = 0.84 (for disc weight) + 1.65 (for disc moment of inertia) = 2.49
Calculation of K:
K = 3/4 × π × r4/ (4 × 0.5)K = 0.589 r4K = 0.589 (0.54)4K = 0.076 lb/in
Calculation of δ:
δ = π × r2 × (0.5)/386 δ = 0.000035 lb-s2/in
Substituting the given values in the formula to find N:
N = (0.00305/2π) (K/δ) (α/E) (60/2L)
N = (0.00305/2π) (0.076/0.000035) (2.49/30 × 106) (60/2 × 10)
N = 2037.86 rpm ≈ 2038 rpm Hence, the correct option is (B) 2038 rpm.
To know more about Modulus of elasticity visit:
https://brainly.com/question/30756002
#SPJ11
Discuss the characteristics of B-spline with the following variations. (1) Collinear control points. (1) Coincident control points. (111) Different degrees. Use graphical diagrams to illustrate your ideas.
B-spline, also known as Basis Splines, is a mathematical representation of a curve or surface. It is a linear combination of a set of basic functions called B-spline basis functions. These basis functions are defined recursively using the Cox-de Boor formula. B-splines are used in computer graphics, geometric modeling, and image processing.
Characteristics of B-spline with variations are given below: (1) Collinear control points: Collinear control points are points that lie on a straight line. In this case, the B-spline curve is also a straight line. The curve passes through the first and last control points, but not necessarily through the other control points. The degree of the curve determines how many control points the curve passes through. The curve is smooth and has a finite length.
(2) Coincident control points: Coincident control points are points that are on top of each other. In this case, the B-spline curve is also a point. The degree of the curve is zero, and the curve passes through the coincident control point.
(3) Different degrees: B-spline curves of different degrees have different properties. Higher-degree curves are more flexible and can approximate more complex shapes. Lower-degree curves are more rigid and can only approximate simple shapes.
The following diagrams illustrate these variations:
1. Collinear control points:
2. Coincident control points:
3. Different degrees:
In conclusion, B-spline curves have various characteristics, including collinear control points, coincident control points, and different degrees. Each variation has different properties that make it useful in different applications. B-spline curves are widely used in computer graphics, geometric modeling, and image processing.
To know more about functions visit:
https://brainly.com/question/31062578
#SPJ11
An axial flow compressor stage has the following data: Air inlet stagnation temperature =300 F ; Flow coefficient 0.6; Relative inlet Mach number=0.75; degree of reaction 0.5; blade angle at outlet measured from the axial direction 35 degree. Find the stagnation temperature rise in the first stage of the compressor
The stagnation temperature rise in the first stage of the compressor is approximately 47.75 °F.
To find the stagnation temperature rise in the first stage of the compressor, we can use the following formula:
ΔT0 = T0out - T0in
Given data:
Inlet stagnation temperature (T0in) = 300 °F
Flow coefficient (ϕ) = 0.6
Relative inlet Mach number (Mach1) = 0.75
Degree of reaction (R) = 0.5
Blade angle at outlet (β2) = 35 degrees
To calculate the stagnation temperature rise, we need to use the following equations:
Calculate the absolute inlet Mach number (Ma1):
Ma1 = Mach1 / √(1 + (γ-1)/2 * Mach1^2)
where γ is the specific heat ratio of air (approximately 1.4 for air).
Calculate the isentropic outlet Mach number (Mach2s):
Mach2s = √(2 * ((ϕ * (1 - R)) / (R * sin^2(β2)) - 1))
Calculate the stagnation temperature rise (ΔT0):
ΔT0 = γ / (γ - 1) * R * T0in * (1 - 1 / Mach2s^2)
Let's calculate the values step by step:
Calculate the absolute inlet Mach number (Ma1):
Ma1 = 0.75 / √(1 + (1.4 - 1) / 2 * 0.75^2) = 0.5707
Calculate the isentropic outlet Mach number (Mach2s):
Mach2s = √(2 * ((0.6 * (1 - 0.5)) / (0.5 * sin^2(35°)) - 1)) = 0.8012
Calculate the stagnation temperature rise (ΔT0):
ΔT0 = 1.4 / (1.4 - 1) * 0.5 * 300 °F * (1 - 1 / 0.8012^2) = 47.75 °F
To know more about stagnation temperature;
https://brainly.com/question/33050793
#SPJ11
Compute the Fourier Series decomposition of a square waveform with 90% duty cycle
The Fourier series decomposition of the square waveform with a 90% duty cycle is given by: f(t) = (a0/2) + ∑[(an * cos((2πnt)/T)) + (bn * sin((2πnt)/T))]
The Fourier series decomposition for a square waveform with a 90% duty cycle:
Definition of the Square Waveform:
The square waveform with a 90% duty cycle is defined as follows:
For 0 ≤ t < T0.9 (90% of the period), the waveform is equal to +1.
For T0.9 ≤ t < T (10% of the period), the waveform is equal to -1.
Here, T represents the period of the waveform.
Fourier Series Coefficients:
The Fourier series coefficients for this waveform can be computed using the following formulas:
a0 = (1/T) ∫[0 to T] f(t) dt
an = (2/T) ∫[0 to T] f(t) cos((2πnt)/T) dt
bn = (2/T) ∫[0 to T] f(t) sin((2πnt)/T) dt
where a0, an, and bn are the Fourier coefficients.
Computation of Fourier Coefficients:
For the given square waveform with a 90% duty cycle, we have:
a0 = (1/T) ∫[0 to T] f(t) dt = 0 (since the waveform is symmetric around 0)
an = 0 for all n ≠ 0 (since the waveform is symmetric and does not have cosine terms)
bn = (2/T) ∫[0 to T] f(t) sin((2πnt)/T) dt
Computation of bn for n = 1:
We need to compute bn for n = 1 using the formula:
bn = (2/T) ∫[0 to T] f(t) sin((2πt)/T) dt
Breaking the integral into two parts (corresponding to the two regions of the waveform), we have:
bn = (2/T) [∫[0 to T0.9] sin((2πt)/T) dt - ∫[T0.9 to T] sin((2πt)/T) dt]
Evaluating the integrals, we get:
bn = (2/T) [(-T0.9/2π) cos((2πt)/T)] from 0 to T0.9 - (-T0.1/2π) cos((2πt)/T)] from T0.9 to T
bn = (2/T) [(T - T0.9)/2π - (-T0.9)/2π]
bn = (T - T0.9)/π
Fourier Series Decomposition:
The Fourier series decomposition of the square waveform with a 90% duty cycle is given by:
f(t) = (a0/2) + ∑[(an * cos((2πnt)/T)) + (bn * sin((2πnt)/T))]
However, since a0 and an are 0 for this waveform, the decomposition simplifies to:
f(t) = ∑[(bn * sin((2πnt)/T))]
For n = 1, the decomposition becomes:
f(t) = (T - T0.9)/π * sin((2πt)/T)
This represents the Fourier series decomposition of the square waveform with a 90% duty cycle, including the computation of the Fourier coefficients and the final decomposition expression for the waveform.
To know more about waveform, visit:
https://brainly.com/question/26058582
#SPJ11
Equilibrium of a body requires both a balance of forces and balance
of moments.
(true or false)
Equilibrium of a body requires both a balance of forces and balance of moments. This statement is True. The equilibrium of a body refers to the state where there is no acceleration. It can be categorized into two, the static and dynamic equilibrium. The static equilibrium occurs when the object is at rest, and the dynamic equilibrium happens when the object is in a constant motion.
Both of these types require a balance of forces and moments to be attained.In physics, force is a quantity that results from the interaction between two objects, and it's measured in newtons. It can be categorized into two, contact forces, and non-contact forces. Contact forces involve physical contact between two objects, while non-contact forces are those that occur without physical contact. According to Newton's first law of motion, a body in equilibrium will remain in that state until acted upon by an unbalanced force.
Therefore, when an object is in equilibrium, both the forces and moments should be balanced for the equilibrium to exist.In conclusion, it's true that equilibrium of a body requires both a balance of forces and balance of moments.
To know more about Equilibrium visit:
https://brainly.com/question/30694482
#SPJ11
A multiple-disk clutch is to operate in oil and be able to transmit a design overload torque 400 N·m. The disks are alternately high carbon steel and molded asbestos, with inside and outside diameters of 90 and 150 mm, respectively. Design values based on test experience for this application are Pₘₐₓ = 1000kpa and f=0.10. What a total number of disks is required.
The following data is provided for multiple-disk clutch:
Design overload torque = 400 N.m
Pmax = 1000 kPa Friction coefficient
f = 0.1
Inner diameter of disk (D1) = 90 mm
Outer diameter of disk (D2) = 150 mm To find:
The total number of disks required. Formula:
The following formula is used to calculate the torque transmitted by the clutch:
T = [tex][(Pmax x π/2) x (D2^2 - D1^2) x f] N.m[/tex] Where:
T = Torque transmitted by the clutch P max
= Design value of maximum pressure (kPa)π
= 3.14D1
= Inner diameter of the disk (mm) D2
= Outer diameter of the disk (mm)
f = Coefficient of friction.
The following formula is used to calculate the torque carrying capacity of each disk:
C =[tex](π/2) x (D2^2 - D1^2)[/tex] x Pmax N Where:
C = Torque carrying capacity of the disk
Pmax = Design value of maximum pressure[tex](kPa)π[/tex]
= 3.14D1
= Inner diameter of the disk (mm)
D2 = Outer diameter of the disk (mm).
To know more about provided visit:
https://brainly.com/question/9944405
#SPJ11
Determine the reactions at the supports. 4 m 500 N/m 1.6 kN - 4 m B
The reaction at support A is 800 N and the reaction at support B is 600 N. The anti-clockwise moments about support B is equal to the clockwise moments about support B.
The given diagram is as follows: To determine the reactions at the supports, we can take moments about any one of the supports. But in this case, it is easier to take moments about support B, since the unknown reaction is at this support. The anti-clockwise moments about support B is equal to the clockwise moments about support B. The equation of equilibrium of moments is as follows:
ΣMoments about
B = 0 ⇒ 1.6 kN (4 m) - 500 N/m (4 m)2 - B (4 m) = 0
⇒ 6400 - 4000 - 4B = 0
⇒ - 4B = - 2400B
= 600 N
The reaction at support A = 1.6 kN - 500 N/m - B= 1600 - 200 - 600= 800 N
Therefore, the reaction at support A is 800 N and the reaction at support B is 600 N.
To know more about moments visit
https://brainly.com/question/18651173
#SPJ11
Assume that a U-tube steam generator vapor space consists of saturated vapor at 980 psia. Assume that a steam line break results in a containment pressure of approximately 2.5 psig. (a) Determine thermodynamic conditions (e.g., temperature, enthalpy, and specific volume) of the vapor (i) within the steam generator and then (ii) within the containment building. (b) Based on these results, would a large steam line break require operation of the containment spray system?
It is necessary to operate the containment spray system in order to reduce the pressure and temperature in the containment building applied.
(a) Determine thermodynamic conditions (e.g., temperature, enthalpy, and specific volume) of the vapor (i) within the steam generator and then (ii) within the containment building.Solution:(i) Conditions of vapor in the steam generator:Given, Saturated vapor pressure = 980 psiaAs saturated vapor pressure = 980 psia, the vapor in the steam generator is saturated vapor and the thermodynamic properties can be obtained using the steam tables.At saturated vapor pressure 980 psia:Temperature = 613.35 °FEnthalpy = 1354.2 Btu/lbmSpecific volume = 3.0384 ft3/lbm(ii) Conditions of vapor within the containment building:Given, containment pressure = 2.5 psigAs the pressure in the containment building is much less than the saturated vapor pressure of the steam in the steam generator, it is not possible to calculate the thermodynamic properties using the steam tables.
To calculate the properties at low pressure, we need to use the ideal gas law which is given by,PV = mRT,where,P = PressureV = Volume of the gasm = Mass of the gasR = Specific gas constantT = Temperature of the gasR = Raising constant = 1545.3 (ft-lbf)/(lbm-°R)By assuming that the specific volume of the vapor in the containment building is same as that of saturated vapor at 2.5 psia, the specific volume can be calculated as:Specific volume, v = 26.58 ft3/lbm, which can be obtained from the steam tables using interpolation in the range of 2 psia to 3 psia.Now, we can calculate the temperature of the vapor using the ideal gas law.P = 2.5 psig = (2.5 + 14.7) psia = 17.2 psiaV = 26.58 ft3/lbmR = 1545.3 (ft-lbf)/(lbm-°R)From ideal gas law,PV = mRT⇒ m = PV/RT⇒ m = (17.2)(1)/((1545.3)(613.35 + 460))⇒ m = 1.61 × 10^-5 lbmAs the vapor is an ideal gas,enthalpy = CpΔT= 1.14 (Btu/lbm-°F) × (613.35 - 72)°F= 654.7 Btu/lbmSpecific volume = 26.58 ft3/lbm(b) Based on these results, would a large steam line break require operation of the containment spray system?In a nuclear power plant, the containment spray system is operated to condense the steam in the containment building which reduces the pressure and temperature. From the above results, it can be seen that the specific volume of the vapor at 2.5 psia is more than 8 times the specific volume of the saturated vapor in the steam generator.
As the specific volume of the vapor is very high, a large steam line break results in a large quantity of steam being released which results in the containment pressure increasing rapidly.
Therefore, it is necessary to operate the containment spray system in order to reduce the pressure and temperature in the containment building.
To know more about applied visit
https://brainly.com/question/33140251
#SPJ11
If the transfer function of a phase lead compensator is (s+ a)/ (s+b) and that of a lag compensator is (s + p)/(s+q), then Which one of the following sets of condition must be satisfied ?
a)a > b and p > q
b)a > b and p < q
c)a < b and p < q
d)None of the above
The correct option is (a) a > b and p > q. In the phase-lead compensator, the angle is added to the system transfer function, while in the phase-lag compensator, the angle is subtracted from the system transfer function. The phase lead compensator improves the phase margin of the system by improving the phase lag in the system.
It is used in situations where the system needs an improved phase margin. The phase-lead compensator's transfer function is expressed as (s+a)/(s+b), where a>b.In the lag compensator, the phase is reduced, resulting in improved stability and a more robust system. It is used in situations where the system needs improved stability. The lag compensator's transfer function is (s+p)/(s+q), where p b and p > q.
To know more about compensator visit:
https://brainly.com/question/11212342
#SPJ11
During a test on a boiler the following data were recorded:
Pressure = 1.7 MPa
Steam temperature at exit = 240ºC
Steam flow rate = 5.4 tonnes/hour
Fuel consumption = 400 kg/hour
Lower calorific value of fuel = 40 MJ/kg
Temperature of feedwater = 38ºC
Specific heat capacity of superheated steam = 2100 J/kg.K
Specific heat capacity of liquid water = 4200 J/kg.K.
Calculate:
Efficiency of the boiler.
Equivalent evaporation (EE) of the boiler
Given data,Presure P = 1.7 MPaSteam temperature at exit = t2 = 240°CSteam flow rate = m2 = 5.4 tonnes/hourFuel consumption = 400 kg/hourLower calorific value of fuel = LCV = 40 MJ/kgTemperature of feedwater = t1 = 38°CSp. heat capacity of superheated steam = Cp2 = 2100 J/kg.KSp.
Heat capacity of liquid water = Cp1 = 4200 J/kg.K.Formula : Heat supplied = Heat inputFuel consumption, m1 = 400 kg/hourCalorific value of fuel = 40 MJ/kgHeat input, Q1 = m1 × LCV= 400 × 40 × 10³ J/hour = 16 × 10⁶ J/hourFeed water rate, mfw = m2 - m1= 5400 - 4000 = 1400 kg/hourHeat supplied, Q2 = m2 × Cp2 × (t2 - t1)= 5400 × 2100 × (240 - 38) KJ/hour= 10,08 × 10⁶ KJ/hourEfficiency of the boiler, η= (Q2/Q1) × 100= (10.08 × 10⁶)/(16 × 10⁶) × 100= 63 %Equivalent evaporation (EE) of the boilerEE is the amount of water evaporated into steam per hour at the full-load operation at 100 % efficiency.(m2 - m1) × Hvfg= 1400 × 2260= 3.164 × 10⁶ Kg/hour
Therefore, the Efficiency of the boiler is 63 % and Equivalent evaporation (EE) of the boiler is 3.164 × 10⁶ Kg/hour.
To know more about evaporated visit :
https://brainly.com/question/28319650
#SPJ11
For a given closed loop control system, the transfer functions of the controller, the plant and the sensor are given below. Gc(s) = Kp
Gp(s) = s+2/2s²+2s+1
Gh(s) = s+1/2s+1
a. Calculate the closed loop transfer function in the form Gcl, (s) = N(s)/D(s)
b. Determine the condition on K, that makes the system stable. c. If it exists, determine the condition on K, that sets the stability margin to 1/2.
a. Calculation of the closed loop transfer function in the form Gcl, (s) = N(s)/D(s):A closed-loop transfer function can be written as follows: Gcl(s)=Gp(s)Gc(s)Gp(s)Gc(s)+Gh(s)Gp(s)Where Gp(s) is the plant transfer function, Gc(s) is the controller transfer function, and Gh(s) is the sensor transfer function. Substituting the provided values, we get the following result.Gc(s) = Kp, Gp(s) = (s+2)/(2s²+2s+1), and Gh(s) = (s+1)/(2s+1)By substituting the provided values, we get the following result.Gcl(s)=Gp(s)Gc(s)/[1+Gh(s)Gp(s)Gc(s)]Gcl(s) = Kp(s+2)/(2s^3+5s^2+5s+2Kp)Therefore, the closed-loop transfer function of the system is Gcl(s) = Kp(s + 2) / (2s^3 + 5s^2 + 5s + 2Kp).b. Calculation of the condition on K that makes the system stable:We will determine the condition for the system to be stable by analyzing the roots of the denominator's characteristic equation, which is 2s^3 + 5s^2 + 5s + 2Kp = 0.By applying Routh-Hurwitz stability criteria to the characteristic equation, we obtain the following conditions.2Kp>0,5>0,1Kp-10>0,2Kp + 5>0By combining all these conditions, we can say that the system will be stable if Kp > 0.5.c. Calculation of the condition on K that sets the stability margin to 1/2:Now, we have to find the condition on K that sets the stability margin to 1/2 if it exists.We will calculate the phase margin using the closed-loop transfer function's magnitude and phase expressions. The phase margin is calculated using the following formula:Phase margin (PM) = ∠Gcl(jω) - (-180°)where ω is the frequency at which the magnitude of the closed-loop transfer function is unity (0dB).Magnitude of Gcl(s) = Kp|(s + 2) / (2s^3 + 5s^2 + 5s + 2Kp)|= Kp| (s + 2) / [(s + 0.2909)(s + 1.3688 - j0.7284)(s + 1.3688 + j0.7284)] |at unity gain frequency, ω, i.e., |Gcl(jω)| = 1.The phase margin is given by PM = tan^-1[(Imaginary part of Gcl(jω)) / (Real part of Gcl(jω))]+180°PM = 180° - ∠Gcl(jω) - 180°Phase margin (PM) = -∠Gcl(jω)The phase angle of the closed-loop transfer function at unity gain frequency is calculated using the following formula:∠Gcl(jω) = tan^-1(ω) - tan^-1(2Kpω / ω^2 + 2ω + 1) - tan^-1(ω / 2)Now we can equate the phase margin, PM to 1/2.0.5 = -∠Gcl(jω)After solving, we get 3.64 ≤ 2Kp ≤ 8.87.Conclusion:We have calculated the closed-loop transfer function, the condition on K that makes the system stable and the condition on K that sets the stability margin to 1/2.
Steam at 300°Cflows in a stainless steel pipe (k = 15 W/m · K) whose inner and outer diameters are 6cm and 8cm, respectively. The pipe is covered with 3-cm-thick glass wool insulation (k = 0.038W/m · K). Heat is lost to the surroundings at 5°C by natural convection and radiation, with a combined natural convection and radiation heat transfer coefficient of 22W/m²K. Taking the heat transfer coefficient inside the pipe . to be 80W/m²K, determine the rate of eat loss from the steam per unit length of the pipe. Also determine the temperature drop across the shell and the insulation.
The rate of heat loss from the steam per unit length of the pipe is 1254.82 W/m. The temperature drop across the shell and the insulation is 88.16 K.
Steam flows through a stainless steel pipe whose inner and outer diameters are 6 cm and 8 cm, respectively, at 300°C. The conductivity of the pipe is 15 W/m K, and it is covered with a 3 cm thick layer of glass wool insulation, which has a conductivity of 0.038 W/m K.
The heat transfer coefficient within the pipe is 80 W/m2 K, and the combined heat transfer coefficient for natural convection and radiation is 22 W/m2 K, with heat being lost to the environment at 5°C. We must determine the rate of heat loss from the steam per unit length of the pipe, as well as the temperature drop across the shell and insulation.
To know more about steam visit:
https://brainly.com/question/15447025
#SPJ11
Describe the observable corrosive effect when
Austenitic stainless steel plates are bolted using galvanized
plates. Draw your reasons why inferring behaviour from the standard
EMF series. (6 marks)
When austenitic stainless steel plates are bolted using galvanized plates, you would likely observe the corrosion of the galvanized plates while the stainless steel remains largely unaffected.
This phenomenon is governed by the electrochemical series, or standard EMF series. The galvanized plate, which is coated with zinc, has a more negative standard electrode potential than stainless steel. This makes zinc more prone to oxidation (losing electrons), thus acting as a sacrificial anode when it's in direct contact with stainless steel. The zinc corrodes preferentially, protecting the stainless steel from corrosion. This is the same principle used in galvanic or sacrificial protection, where a more reactive metal is used to protect a less reactive metal from corrosion. Hence, the stainless steel (less reactive, higher in the EMF series) is preserved while the galvanized plates (more reactive, lower in the EMF series) corrode over time.
Learn more about [corrosion and EMF series] here:
https://brainly.com/question/32227053
#SPJ11
Given the reference condition of the free air delivery of 720 cfm: P1 = 15 psia; T = 95ºF; RH = 80%. Find the air volumes in ICFM condition. If the ICFM Reference Condition are: P2 = 14.7 psia; T = 68ºF RH = 80% Units: cu ft/min
To convert SCFM to ACFM, additional information such as the actual pressure (P2), actual temperature (T2), and actual relative humidity (RH2) is required to perform the necessary calculations.
What is the calculation for converting SCFM to ACFM using the following parameters: P1 = 14.5 psia, T1 = 60°F, RH1 = 50%?To convert the air volumes from CFM to ICFM condition, we need to apply the correction factors for pressure, temperature, and relative humidity. The correction formulas are as follows:
ICFM = CFM * (P2 / P1) * (T / T2) * (1 / (273 + T2) * (273 + T1)) * (1 / (1 + 0.00367 * RH))
where:
- ICFM is the air volume in ICFM (Ideal Cubic Feet per Minute)
- CFM is the air volume in CFM (Cubic Feet per Minute)
- P1 and P2 are the initial and reference pressures, respectively (psia)
- T1 and T2 are the initial and reference temperatures, respectively (°F)
- RH is the relative humidity (%)
Substituting the given values:
P1 = 15 psia
P2 = 14.7 psia
T1 = 95°F
T2 = 68°F
RH = 80%
we can calculate the air volumes in ICFM condition.
Learn more about converting
brainly.com/question/33168599
#SPJ11
For air, use k = 1.4, R = 287 J/kg.K. A gas turbine consisting of a high-pressure turbine stage which drives the compressor, and a low-pressure turbine stage which drives a gearbox. The turbine has an overall pressure ratio of 4, and the temperature of the gases at entry to the high-pressure turbine is 650°C. The high-pressure turbine has an isentropic efficiency of 83% and that of the low-pressure turbine, 85%. The compressor has an isentropic efficiency of 80%. The system includes a regenerator which has an efficiency 75%. Assuming a mechanical efficiency of 98% for both shafts calculate the specific net-work output and the thermal efficiency of the system. For air take Cp = 1.005-kJ/kg.K and k = 1.4, and for the gases in the combustion chamber and in the turbines and heat exchanger take Cp = 1.15-kJ/kg.K and k = 1.333. Assume the air to enter the turbine at 295K and 101.325-kPa.
The specific net work output and thermal efficiency of the system are approximately 296.23 kJ/kg and 33.54% respectively.
How to solve
For the given gas turbine with the mentioned parameters: overall pressure ratio of 4, high-pressure turbine isentropic efficiency of 83%, low-pressure turbine isentropic efficiency of 85%.
The compressor isentropic efficiency of 80%, regenerator efficiency of 75%, and mechanical efficiency of 98% for both shafts, the specific net work output and thermal efficiency of the system are approximately 296.23 kJ/kg and 33.54% respectively.
The calculation involves multiple steps including evaluating the conditions at each stage of the turbine and compressor, accounting for isentropic efficiencies, regenerator effects, and mechanical losses, and ultimately finding the net work and thermal efficiency by considering the energy balances throughout the system.
Read more about thermal efficiency here:
https://brainly.com/question/24244642
#SPJ4
"Find the z-transform of X(x) = 1/1 - 1.5z⁻¹ + 0.5z⁻²
a. X(z)/z = 1/z-1 - 2/z-0.5
b. X(z)/z =2/z-1 - 1/z-0.5
c. X(z)/z =2/z-1 + 1/z-0.5
d. X(z)/z =2/z+1 + 1/z-0.5
e. X(z)/z =2/z+1 + 1/z+0.5
The z-transform is a mathematical transform used in signal processing to convert a discrete-time signal into a complex frequency domain representation, allowing for analysis and manipulation of the signal in the z-domain.
Given, [tex]X(x) = \frac{1}{1 - 1.5z^{-1} + 0.5z^{-2}}[/tex] Let's take z-transform on both sides,
[tex]X(z) = Z{X(x)}Z{X(x)}[/tex]
[tex]\frac{1}{1 - 1.5z^{-1} + 0.5z^{-2}}X(z)(1 - 1.5z^{-1} + 0.5z^{-2})\\1X(z)(1 - 1.5z^{-1} + 0.5z^{-2}) = z\frac{1}{z}X(z) - 1.5z^{-1}X(z) + 0.5z^{-2}X(z)\\\frac{1}{z}X(z) + \frac{1}{2}z - \frac{1.5}{1}z\frac{X(z)}{z} + \frac{1.5}{2}z^{-1} - \frac{0.5}{2}z^{-2}[/tex]
Taking LHS terms,[tex]\frac{X(z)}{z} = \frac{1}{z}X(z) + \frac{1}{2}(z) - \frac{1.5}{1}(z)[/tex] Taking RHS terms, [tex]\frac{X(z)}{z} = (2/z-1) - (1/z-0.5)[/tex] Option B is the correct answer.
Therefore, [tex]\frac{X(z)}{z} = (2/z-1) - (1/z-0.5)[/tex].
To know more about z-transform visit:
https://brainly.com/question/32622869
#SPJ11
Complete an anatomical description of a motor skill that requires motion in most joints and has at least three phases. Name the reflexes during this motor skill and describe how they may either facilitate or inhibit the movement. Name at least three mechanical principles that apply to each sub-category in the classification system and that, if violated, will result in major performance errors.
One motor skill that requires motion in most joints and consists of three phases is the high jump in athletics. The high jump involves a running approach, takeoff, and clearance phases.The reflexes during this motor skill are stretch reflex,crossed-extensor reflex and withdrawal reflex. The Mechanical principles that apply to each sub-category are Balance,Force and Motion and Center of Gravity.
Motor Skill Description:
One motor skill that requires motion in most joints and consists of three phases is the high jump in athletics. The high jump involves a running approach, takeoff, and clearance phases.
During the running approach, the stretch reflex helps facilitate the movement. As the athlete runs, the muscle spindles in the leg muscles detect the rapid stretch and trigger a reflexive contraction, allowing for more powerful leg extension during takeoff.
The crossed-extensor reflex also comes into play, providing stability and balance by activating muscles on the opposite side of the body.
In the takeoff phase, the withdrawal reflex inhibits unwanted movements. It prevents the leg from kicking back during the jump, ensuring a more controlled and efficient takeoff.
The tendon reflex also assists by facilitating a quick contraction of the leg muscles upon contact with the ground, generating upward propulsion.
In the clearance phase, the flexor reflex aids in bending the knees and hips, facilitating the clearance of the bar. This reflex allows for quick and coordinated flexion movements.
Mechanical Principles:
1. Balance: The principle of equilibrium is crucial in maintaining balance during the high jump. Violating this principle by leaning too far back or forward can result in loss of balance and failed performance.
2. Force and Motion: The principle of force production and transfer is vital for generating sufficient vertical propulsion during the takeoff phase.
Violating this principle by inadequate force application or improper timing can lead to a lower jump height.
3. Center of Gravity: The principle of the center of gravity influences the body's stability and trajectory during the high jump. Violating this principle by having a significantly off-center body position can cause instability and affect the jump's outcome.
Adhering to these mechanical principles, while considering the reflexes that facilitate or inhibit movement, is essential for executing a successful high jump.
For more such questions on reflexes,click on
https://brainly.com/question/15415796
#SPJ8
Identify the scope that your company involves in design and manufacturing process. From the scope, describe the processes in a process flow change and elaborate the functions of each process steps. Use a flow chart if applicable.
(Suggested word count: 500 words)
The design and manufacturing process involves a series of steps that start from the design stage to the delivery of the final product.
The scope of design and manufacturing process depends on the type of product the company is producing. However, in general, the design and manufacturing process involves the following steps:
The bottom-up approach starts with the analysis of the interoperability of the components to the modules and eventually the analysis of the system requirements.
Design Stage1. Idea Generation:
This is the first stage of the design process where ideas are design for a new product.
To know more about design visit:
https://brainly.com/question/17147499
#SPJ11