Answer: True
Explanation:
flhsmv lesson 6 circle the road way user who must yield the right of way
Answer:
entering drivers
Explanation:
Drivers entering a traffic circle must yield the right-of-way to those already in the traffic circle. (Among other things, this rule helps avoid gridlock.)
Answer:
entering driversthe road way user who must yield the right of way(HVAC) PLEASE HELP neeed helpp
# derive is a kind of which dependency
Switching to first order kinetics, enzymes are immobilized in 6 mm radius (R) beads. Beads are immersed in a solution containing substrate at a concentration (CAs) of 22 gmol/m3. The observed reaction rate (rA,obs) of the heterogeneous reaction is 4.3 x 10-6 gmol/sec. The first order rate constant (k1) is 0.24 /sec. Calculate the hypothetical rate, r*As of the reaction in this system.
Air enters the combustor of a jet engine at Pressure=10 atm, T=1000R and M=0.2. Fuel is injected and burned with fuel-air ratio (by mass) of 0.06. The heat released during the combustion is 4.50000000 ft-lb per slug of fuel. Assuming one-dimensional frictionless flow with r=1.4 for the fuel-air mixture, calculate M2, p2 and T2 at the exit of combustor?
180 kg/h of a liquid feed enters an extraction column with 98% paraffin oil and 2% ethyl alcohol at room temperature and pressure. Liquid absorbent is 100% water. Required recovery (extraction) of ethyl alcohol from paraffin oil is 97%. Given that paraffin oil and water are immiscible with each other and the extraction column operates in a counter current fashion. Assume isothermal and isobaric conditions and that only ethyl alcohol is absorbed. Equilibrium relation between mass fractions of ethyl alcohol in water and paraffin oil is given by Xwater = 1.7544 * Xparaffin oil (a) Find minimum amount of water required (Answer – 97.5 kg/hr) (b) If you have 1.5 times minimum water amount, how many equilibrium stages are required? (Answer ~ 6)
Iman wanted to find out at what temperature butter melts. She placed a cube of solid butter in a beaker. She put the beaker on a hot plate. She turned up the temperature dial one degree every two minutes. Then she recorded the temperature at which the butter started to melt.
Iman wanted to determine if her results were reliable. She decided to repeat the experiment. Which statement describes the main purpose of repeating the experiment?
to test a different substance
to see if the results are similar
to practice completing experiments
to determine if butter will melt twice
Answer:
Ans: To see if the results are similar
Air at 1.00 atm is passed through a horizontal 1.5-in. Schedule 40 (steam-jacketed) steel pipe at a velocity of 2.10 ft/s and an inlet and outlet temperature of 25.0 °C and 95.5 °C, respectively. The pipe wall temperature is maintained at 121.1 °C. (HINT: You may neglect the viscosity correction in your calculations.) a) Assuming only heat transfer by forced convection, how long must
Answer:
missing question; How long must the heated section be
answer : 5.898 meters
Explanation:
Given parameters:
Diameter of steel pipe = 1.5 inches = 0.0381 m
velocity of air = 2.10 ft/s = 0.64 m/s
Inlet temperature = 25°C
Outlet temperature = 95.5°C
pipe wall temperature = 121.1°C
Average temperature = ( 25 + 95.5 ) / 2 = 60.25°
determine Reynolds number of air at 60.25°
= VD / v = ( 0.64 * 0.0381 ) / ( 1.83 * 10^-5 )
= 1332.46 this means the flow is laminar
hence mass flow rate ( m ) = eAv = 1.08 * πd^2 * velocity
= 1.08 * 0.0046 * 0.64 = 0.0032 g/s
attached below is the remaining part of the solution
(TCO 3) Below is the frequency response of the IIR realization of an analog band-pass filter. What type of filter is this?
Answer:
Hello the frequency response is missing attached below is the missing image
answer : Elliptic Filter
Explanation:
The filter with such frequency response that is an analog band-pass filter as well is called an Elliptic filter.
And this is because an Elliptic filter posses a constant ripple in the stop band and a unity gain is seen in the pass band
How do Geothermal plowerplants relate to engineering?
Una cuerda fuertemente estirada tiene sus puntos extremos fijos en x=0 y x=L. Si se le da un desplazamiento inicial F(x)=ax(L-x) desde la posición de equilibrio. Donde a es una constante y luego se suelta, encuentre el desplazamiento en cualquier tiempo t>0. Donde c=1/π.
Answer is in a photo. I couldn't attach it here, but I uploaded it to a file hosting. link below! Good Luck!
bit.[tex]^{}[/tex]ly/3a8Nt8n
In order to be a Mechanical Engineer, you need to:
1. Have a Bachelor's Degree
2. Have a Master's Degree
3. Have a Ph.D.
Answer:
3
Explanation:
it is compulsory to have a bachelor's degree
If we want to create a single function for insertion and deletion in the linked list, Suggest any approach by which this task can be carried out. Just verbally explain how we can accomplish this, no need to write the code
Answer:
Explanation:
One approach to this would be to create the function with two parameters. One would be the element to be added or deleted while the other would be a char variable that would indicate the process to be completed (adding or deleting). This char can have a value of '+' or '-' accordingly. Then within the function, we would use an IF/Else statement to detect whether the char variable had a value of '+' or '-'. If the value was '+' we would execute the insertion process of the code but if the value was '-' we would only execute the deletion process of the code. Therefore, allowing both processes to be available within a single function.
name the process by which mild steel can be converted into high carbon steel and explain it briefly ?
Answer:
please give me brainlist and follow
Explanation:
Mild steel can be converted into high carbons steel by which of the following heat treatment process? Explanation: Case hardening, also referred as carburizing increases carbon content of steel, thus, imparting hardness to steel.