TRUE OR FALSE? Alloys are used more than pure metals because they are generally softer and less likely to react with air or water. WILL GIVE BRAINLIEST

If we add water to a concentrated acid, then the solution may boil very violently, splashing concentrated acid. If add acid to water, the solution that forms is very dilute and a small amount of heat is released.

When a strong acid is poured into water, it flows down the flask and mixes much better, so no boiling takes place. The addition of water to acid forms an extremely concentrated solution of acid initially. A large amount of heat is released and the solution may boil very violently, splashing concentrated acid out of the beaker and all this because the reaction is exothermic in nature.

The reason this takes place is due to a large amount of energy liberated in the hydration reaction of concentrated ions. Therefore, we add acid to water dropwise for the dilution with constant stirring and not water to acid directly.

If we add water to acid, then an exothermic reaction occurs and the solution may boil very violently. To form the dilute solution of any strong acid, you should add acid to water and the small amount of heat released is not sufficient to vaporize and spatter it.

Learn more about dilution of acid, here:

https://brainly.com/question/

#SPJ2

Answer:

liquid

Explanation:

correct answer hope it helps

This follows a simple conversion technique. Basically what the question is trying to say here is to convert 29.1 inHg to mmHg. 1 inHg is equal to 25.4 mmHg so 29.1 inHg would be equal to [tex]25.4 * 29.1[/tex] which when evaluated turns out to be: [tex]739.14[/tex]. :D

The pressure will be 739.14 mm Hg.

The SI unit measuring pressure would be the pascal, which measures the force of each unit area of the surface.

Calculation of pressure

It is known that 1inHg = 25.4 mm Hg.

Hence, the pressure = 25.4 × 29.1 = 739.14 mm Hg

Therefore, the pressure will be 739.14 mm Hg.

To know more about pressure

https://brainly.com/question/15175692

#SPJ2

Answer:

Purple light.

Yellow light.

Explanation:

Answer:

The flask has to be closed during the hydrochloric acid and sodium carbonate reaction as the resultant gas got trapped inside the closed flask.

Explanation:

The hydrochloric acid and sodium carbonate reaction was exothermic that caused the pressure to decrease. The flask has to be closed during the hydrochloric acid and sodium carbonate reaction as the resultant gas got trapped inside the closed flask.

In exothermic reactions, energy is produced in the form of heat or light.

Answer:

We can see that the atomic radius decreases across every row.

Explanation:

I will comment more below.

The elements that represent the highest points on the graph are all elements of group 1 and occur at the head of the period to which they belong.

The periodic table is an arrangement of elements in groups and periods. The elements in the same group have the same number of valence electrons while the elements in the same period have the same number of shells.

Looking at the graph, we can see that the high points in the graph all correspond to the group 1 elements; sodium, potassium, rubidium and cesium.The have the highest atomic radii in the period. Atomic radii increases down the group but decreases across the period. Remember that these elements are at the head of the period to which they belong hence they have the highest atomic radii.

Learn more: https://brainly.com/question/9352088

Answer:

349.22°C

Explanation:

Let the final temperature of the two pieces of metal be x.

Now, the warmer metal which is C u reduces from 475°C to x. Thus Δt for C u is; Δt1 = 475 - x.

The cooler metal Cr increases in temperature from 265°C to x. Thus, it's change in temperature is Δt for Cr is; Δt2 = x - 265.

Now from conservation of energy, the amount of energy leaving the C u metal is equal to the amount of energy entering the Cr metal.

Thus;

q_lost = q_gain

Where;

q_lost = m1•c1•Δt1

q_gained = m2•c2•Δt2

Now, c1 & c2 are the specific heat capacity of C u and Cr respectively.

From online tables, c1 = 0.385 J/g°C and c2 = 0.46 J/g°C

We are given;

m1 = 12g and m2 = 15g

Thus;

12 × 0.385 × (475 - x) = 15 × 0.46 × (x - 265)

2194.5 - 4.62x = 6.9x - 1828.5

6.9x + 4.62x = 2194.5 + 1828.5

11.52x = 4023

x = 4023/11.52

x = 349.22°C

Answer: The percent yield of the reaction is 77.0 %

Explanation:

[tex]2Pb+O_2\rightarrow 2PbO[/tex]

[tex]\text{Number of moles}=\frac{\text{Given mass}}{\text{Molar mass}}[/tex]

[tex]\text{Number of moles of lead}=\frac{451.4g}{207.2g/mol}=2.18moles[/tex]

[tex]\text{Number of moles of lead oxide}=\frac{374.7g}{223.2g/mol}=1.68moles[/tex]

According to stoichiometry:

2 moles of [tex]Pb[/tex] produces = 2 moles of [tex]PbO_2[/tex]

2.18 moles of [tex]Pb[/tex] is produced by=[tex]\frac{2}{2}\times 2.18=2.18moles[/tex] of [tex]PbO_2[/tex]

Mass of [tex]PbO_2[/tex] =[tex]moles\times {\text {Molar mass}}=2.18\times 223.2g/mol=486.6[/tex]

percent yield =[tex]\frac{374.7g}{486.6g}\times 100=77.0\%[/tex]

Answer: Spun yarn is made by twisting staple fibers together

To make a cohesive thread Or “single”. Twisting fibers, into yarn in the process called spinning can be dated back to the upper Paleolithic. Yarn spinning was one of the first processes to be industrialized.

Explanation: