Thermal energy is released when calcium chloride dissolves in water. It is absorbed when ammonium chloride dissolves in water. Which substance will you use in your design?

Answers

Answer 1

Answer:calcium chloride

i think this is helpful

Explanation:


Related Questions

if this light stays on after the initial startup of the vehicle it signals a warning that there is something wrong with the service brake system. a) vehicle function indicators b) dashboard warning devices c) oil pressure indicator d) coolant temperature indicator e) electrical system indicator f) service brake system indicator

Answers

Service brake system indicator is the warning that there is something wrong with the service brake system.  Hence option f is correct.

What is indicator?

Amber-colored indicator lights can be found at the front, back, and occasionally on the left and right sides of the vehicle. Whether you're turning left, right, or into oncoming traffic, you use your indicators to signal your planned change of direction.

When this light turns on, one of two things will happen. Either the parking brake is engaged or the hydraulic fluid (brake fluid) in the master cylinder is low. Your brakes are made up of a system of hydraulic oil-filled tubes called brake lines.

Thus, service brake system indicator is the warning that there is something wrong with the service brake system.  Hence option f is correct.

To learn more about indicator, refer to the link below:

https://brainly.com/question/28093573

#SPJ1

what is the output frequency of a three-stage binary counter with an input clock frequency of 80 khz?

Answers

The lowest output frequency that can be used with a cascaded counter if a clock frequency is applied is: The output frequency that is lowest will be = [tex]2.5kHz[/tex]

What is the counter's output frequency?No matter whether the counter is synchronous or asynchronous, the output frequency for a binary counter or M mod counter is f/2n, where f is the input frequency and n is the number of flip-flops (but only if the duty cycle is 50%).A counter is a device that stores (and occasionally displays) the number of times a specific event or process has occurred in digital logic and computing, frequently in relation to a clock.The most typical kind is a sequential digital logic circuit, which has several output lines and a clock-input line.A binary three-stage counter counts.[tex]2^{2} = 8[/tex] states.Hence the output frequency is[tex]80/23=80/8=10KHz[/tex]What is a 4-bit binary counter's output frequency for a 160 MHz input clock? A 4-bit counter's final flip flop's output is equal to the input clock/16.Thus, the output frequency is 160MHz/16, or 10MHz.

TO learn more about counter's output frequency refer to:

https://brainly.com/question/26000993

#SPJ4

a steel component is nickel plated to give corrosion protection. to increase the strength of the bond between the steel and the nickel, the component is heated for 4 h at 1000c. if the diffusion parameters for nickel in iron are do ¼ 1.9 104 m2 /s and qd ¼ 284 kj/mol, how far would you expect the nickel to diffuse into the steel in this time?

Answers

Diffusion coefficient, D = 3.77 × 10⁻⁶ m²/s

Thus, approximate depth of diffusion is 2.3 microns.

What is diffusion?

Diffusion is a process that results from molecules moving randomly and that allows matter to move from one area of high concentration to another area of low concentration. A well-known illustration is how quickly a flower's fragrance fills a room's still air.

Thermal energy that is transported or diffused from a temperature that is higher to one that is lower constitutes heat conduction in fluids. Neutrons must diffuse through a medium, where they frequently scatter but very infrequently absorb, in order for a nuclear reactor to operate.

According to research, the gradient in concentration is directly correlated with the rate of flow of the diffusing substance.

Learn more about diffusion

https://brainly.com/question/94094

#SPJ4

a single-threaded 25-mm power screw is 25 mm in diameter with a pitch of 5 mm. a vertical load on the screw reaches a maximum of 5 kn. the coefficients of friction are 0.06 for the collar and 0.09 for the treads. the frictional diameter of the collar is 45 mm. find the overall efficiency and the torque to ""raise"" and ""lower"" the load.

Answers

The torque required to raise the load is 15.75 N-m. The torque required to lower the load is 7.81 N-m.

The overall efficiency is 0.252

What is torque?

Torque is the force that can cause an object to rotate around an axis. In linear kinematics, force is what causes an object to accelerate. Similarly, torque is responsible for angular acceleration.

As a result, torque is defined as the rotational equivalent of linear force. The axis of rotation is the straight line around which the object rotates. Torque is simply the tendency of a force to turn or twist in physics.

Torque is described using a variety of terms, including moment and moment of force. The moment arm or lever arm is the distance between the point of application of force and the axis of rotation.

Learn more about torque

https://brainly.com/question/17512177

#SPJ4

"smart" wifi devices which are equipped with more sensors, tend to use more energy or watts than old fashioned single contact devices.

true or false?

Answers

Answer: true     explanation:Smart home devices like thermostats and appliances are highly efficient because they can automatically adjust to changing energy needs. Plus, they can detect inefficiencies so electricity, water, and gas waste can be minimized. Your energy consumption can be reduced exponentially when smart devices run your home.

technician a says a worn or damaged idler arm can cause front-end shimmy. technician b says a worn or damaged idler arm can cause hard steering. who is correct?

Answers

Insufficient power steering fluid in your system is the most frequent cause of a stiff steering wheel.

What can be a sign that the steering system's parts are damaged?Any noises emanating from the steering wheel could be an indication of a broken steering belt, worn internal gears, or insufficient steering fluid. A new belt must be purchased right away if there is a belt problem. When making a turn, have you noticed a whining or a delayed response? The pump might be about to stop working.Insufficient power steering fluid in your system is the most frequent cause of a stiff steering wheel. This frequently occurs when there is a system leak coming from the pressurized hose location. The majority of the time, the reason for the fluid leak is a fractured or loose hose.  

To learn more about Steering refer to:

https://brainly.com/question/14183688

#SPJ4

a wind turbine rotates at 19 rev/min. if its power output is 4.0 mw, what is the torque produced on the turbine from the wind (in n · m)?

Answers

The torque produced on the turbine from the wind  is 2 000 kN/m². Torque is the rotating equivalent of force in physics and mechanics.

What is torque?

Torque is the rotational equivalent of linear force in physics and mechanics. Depending on the field of study, it is also known as the moment, moment of force, rotational force, or turning effect. It represents a force's ability to cause a change in the rotational motion of the body.

The number of revolution per minute of the turbine = 19 rev/min

The power output of the turbine = 4.0 MW

The power transmitted to a shaft equation is given as follows;

P = 2* N * T * π / 60

Where;

P = The power transmitted to a turbine shaft = 4.0 MW

N = The number or revolutions per minute = 19 rev/min

T = The torque produced on the turbine by the wind

Therefore

Torque T = P *60 / 2 * N * π  = 4.0 * 60 / 2 *  π * 19 = 240 / 38 *  π

= 6.31 /  π

The torque produced on the turbine from the wind = 6.31/π MN·m

≈ 2 MN·m² = 2 000 kN/m² .

To learn more about torque refer :

https://brainly.com/question/20691242

#SPJ4

if a 25 kva transformer had a primary voltage of 4,800 volts and an output voltage of 240 volts, what would the maximum primary and secondary amperage's be before overload?

Answers

The maximum primary and secondary amperage's be before overload :

25 KVA/2400 = 10.4 Amps (Primary)25 KVA/120 = 208.3 Amps (Secondary)50 KVA/4800 = 10.4 Amps (Primary)50 KVA/ 240 = 208.3 Amps (Secondary)

What happens when transformer is overloaded?kVA, voltage, and current should be compared to the transformer's nameplate. There probably is an overload if the power consumption exceeds the information on the nameplate.You may argue that the transformer will be overloaded once the temperature rise brought on by loading exceeds the rated rise as specified by the manufacturer. Temperature rise affects a transformer's insulating life to some extent.If the transformer is repeatedly overloaded, the system will deteriorate faster. A weaker insulating system is the end outcome of gradual, minor changes in loading capacity. Overloading leads to overheating, which finally results in thermal deterioration that affects the insulation through fractures.

Explanation :

A typical household service might be rated 120/240 volts, 100 amperes. This means at full load the customer requires 100 amps at 240 volts. The power needs would be 240 x 100=24,000 volt amps or 25 kVA. A 25 kVA transformer would easily supply this load. Similarly, a service rated 240 volts; 200 amperes would have a power capacity of 240 x 200 = 48,000 volt amps or 48 kVA and would need a 50 kVA transformer.

Learn more about transformer overload refer to :

https://brainly.com/question/12017821

#SPJ4

determine the change in the internal energy of helium, in kj/kg, as it undergoes a change of state from 100 kpa and 20°c to 600 kpa and 300°c using the equation of state

Answers

The change in the internal energy of helium is 873.6 kJ/KG.

What is ideal gas equation ?In this situation, the ideal gas law, often known as an equation of state, governs all gases: The universal (or perfect) gas constant, 8.31446261815324 joules per kelvin per mole, and n, the number of moles of the gas, are the two inputs into the formula PV, which equals nRT.The relationship between a gas's pressure P, volume V, and temperature T in the range of low pressures and high temperatures, when the gas's molecules move virtually independently of one another, is known as the ideal gas law, also known as the perfect gas law.The International System of Units uses the units of joules, cubic meters (m3), newtons (N), pascals (Pa), and newtons per square meter (N/m2) to measure energy, volume, force, and pressure.

Find the attachment answer

Learn more about ideal gas equation refer to :

https://brainly.com/question/1056445

#SPJ4

a 12-bit bipolar dac has a 10.00-v reference. find out: (6 pts) a. what output voltage will be resulted from digital inputs of 4a6h, 02bh, and d5dh?

Answers

A 12-bit bipolar dac has a 10.00-v reference, the output voltage from digital inputs of

4a6h, v₀ = 2.906 v

02bh, v₀ = 0.105 v

d5dh, v₀ = 8.3541 v

What is voltage?

An electrical circuit's power source exerts pressure known as voltage on charged electrons (current), causing them to flow through a conducting loop and perform tasks like lighting a lamp.

Voltage is measured in volts and is simply equal to pressure. It honors Italian physicist Alessandro Volta (1745–1827), who developed the voltaic pile, the predecessor to the modern household battery.

Voltage was first known as electromotive force in the early history of electricity. For this reason, voltage is denoted by the letter E in equations like Ohm's Law.

The difference in electric potential between two points is known as voltage, also spelled as electric pressure, electric tension, or electric potential difference. It is equivalent to the work required to move a test charge between two points in a static electric field.

Learn more about voltage

https://brainly.com/question/2526786

#SPJ4

a 4-ton air conditioner removes 5.06 × 10 7 j 5.06×107 j (48,000 british thermal units) from a cold environment in 1.00 h. (a) what energy input in joules is necessary to do this if the air conditioner has an energy efficiency rating ( e e r ) (eer) of 12.0? (b) what is the cost of doing this if the work costs 10.0 cents per 3.60 × 10 6 j 3.60×106 j (one kilowatt-hour)? (c) discuss whether this cost seems realistic. note that the energy efficiency rating ( e e r ) (eer) of an air conditioner or refrigerator is defined to be the number of british thermal units of heat transfer from a cold environment per hour divided by the watts of power input.

Answers

(a) Energy input in joules that is necessary to do this if the air conditioner has an energy efficiency rating (eer) of 12.0 is, W = 1.44 × 10⁷ Joules.

(b) The cost of doing this if the work costs 10.0 cents per 3.60 × 10⁶ j is, Cost = $0.4 or 40 cents.

What is energy?

In physics, energy is the quantifiable property that is transferred to a body or to a physical system and is observable in the production of work as well as in the form of heat and light. Energy is a conserved resource; according to the law of conservation of energy, energy can only change its form; it cannot be created or destroyed. The joule is the unit of measurement for energy in the International System of Units (SI) (J).

Common types of energy include the kinetic energy of a moving object, the potential energy held by an object, the elastic energy held in a solid object, the chemical energy linked to chemical reactions, the radiant energy carried by electromagnetic radiation, and the internal energy contained within a thermodynamic system.

Learn more about energy

https://brainly.com/question/13881533

#SPJ4

problem 1: (a) design a compound 2-stage reverted gear train as a speed increaser to provide a total speed increase of exactly 48:1. minimize the gearbox size and use 20° pressure angle full depth gears all with the same diametral pitch, and avoid interference. show a simple scaled sketch or drawing of your meshed gears and clearly give the number of teeth on each gear (n2, n3, n4, n5). (b) repeat this with a 22.5° pressure angle. (c) using a diametral pitch of 16, what is the distance between the shafts, d, in cases (a) and (b)?

Answers

The distance between the shafts, d, in cases (a) and (b) Using a diametral pitch of 16 is, D = 29.56m

What is distance?

Distance is a measurement of how far apart two objects or points are, either quantitatively or occasionally qualitatively. Distance in physics or common usage can refer to a physical length or an estimate based on other factors (e.g. "two counties over").

The term is frequently used metaphorically to refer to a measurement of the difference between two similar objects (such as statistical distance between probability distributions or edit distance between strings of text) or a degree of separation since spatial cognition is a rich source of conceptual metaphors in human thought (as exemplified by distance between people in a social network).

The concept of a metric space is used in mathematics to formalize the majority of such notions of distance, both literal and figurative.

Learn more about distance

https://brainly.com/question/2854969

#SPJ4

an 8-bit a/d converter has a reference voltage of 10 v. (5 pts) a. what is the resolution of the a/d converter?

Answers

The smallest incremental voltage that the ADC can detect and recognize without changing the digital output is referred to as the resolution.

A DAC's resolution can be determined in what ways?The formula Resolution = (Range /(2n -1)) is used to calculate resolution for n-bit DACs. which will result in the slightest alteration the DAC can detect. Range, on the other hand, is the maximum value that a DAC can measure.The smallest incremental voltage that the ADC can detect and recognize without changing the digital output is referred to as the resolution. The ADC output bit count is how it is expressed. So an ADC with a resolution of 12 bits is one that converts an analog signal to a 12-bit digital value.      

To learn more about Resolution refer to:

https://brainly.com/question/2267795

#SPJ4

Other Questions
I need help with this If log(4x + 6) = 4, then x = ____You may enter the exact value or round to 4 decimal places. judging from the organization's description, ciea could be best categorized as what kind of interest group? a cone has volume of 98cm the radius of the cone is 5.13 what is the hight of the cone In this project you will build a database for a health clinic and load it with data. The database you build in this project will be used in later assignments. Class attendance on both November 5th and 17th is mandatory to earn full credit for this assignment.Project requirements:1) Write the SQL to build a database schema to support the following business operations:CIS 3050 Health is a health clinic. Doctors of various specialties provide treatments to patients. A nurse is always attending the treatments along with the doctor. Patients schedule appointments for treatment with a receptionist. Doctors, nurses, and receptionists are all employees of the clinic. Each receptionist is assigned to a single doctor. A doctor is supported by multiple receptionists.Use a specialization hierarchy for the various employee types (i.e., create an employee table that is a supertype for the doctor, nurse, and receptionist subtype tables). Also use patient, appointment, and a treatment tables.Complete the schema with all seven of the required tables, all required relationships, and attributes for each table.2) Using the completed health clinic schema from the previous step, load the database with the following data:3 doctors4 nurses4 receptionists4 patients6 appointments3 treatmentsEach student must have their own unique data loaded into the database.Demonstrate your data loads for all tables before the end of class on Tuesday November 17th by querying each table individually. what does the acronym reo mean? relayed electronic opengl real estate owned relayed electric online relayed electronic orb Which segments of the american public knew from the outset of the civil war that the conflict was rooted in slavery?. exercise 10-9a record common stock, treasury stock, and cash dividends (lo10-2, 10-4, 10-5) power drive corporation designs and produces a line of golf equipment and golf apparel. power drive has 100,000 shares of common stock outstanding as of the beginning of 2021. power drive has the following transactions affecting stockholders' equity in 2021. march 1 issues 55,000 additional shares of $1 par value common stock for $52 per share. may 10 purchases 5,000 shares of treasury stock for $55 per share. june 1 declares a cash dividend of $1.50 per share to all stockholders of record on june 15. (hint: dividends are not paid on treasury stock.) july 1 pays the cash dividend declared on june 1. which of the following establishes revised national security adjudicative criteria for determining eligibility for initial or continued access to classified information or eligibility to hold a sensitive position? (select one response) When something heats up, new energy is created, and when something cools down, energy is destroyed. If the required reserve ratio is 10% and the fed conducts an open market purchase of $100, what is the maximum possible change in the money supply?. While religious spaces are often sacred for their community of believers, sacred spaces exist both inside and outside of religion. What are two examples of a sacred space and what imbues those sites with their sacredness. find the maximum flow f and a minimum cut. (b) draw the residual graph gf (along with its edge capacities). in this residual network, mark the vertices reachable from s and the vertices from which t is reachable. (c) an edge of a network is called a bottleneck edge if increasing its capacity results in an increase in the maximum flow. list all bottleneck edges in the above network. (d) give a very simple example (containing at most four nodes) of a network which has no bottleneck edges. (e) give an efficient algorithm to identify all bottleneck edges in a network. (hint: start by running the usual network flow algorithm, and then examine the residual graph.) what do asteroids and comets have in common? question 7 options: they have similar densities. most are unchanged since their formation in the solar nebula. they have nothing in common with each other. they have a similar range of orbital inclinations. they have similar orbital radii. Find the cube roots of i. Round all numbers to 3 decimal places. Enter 0s or 1s in the appropriate boxes to answer 0 + i, 1+0i, etc. 1. How would the Egyptian government ensure that enough people were available to harvest the wheat crop? when groups of workers receive a portion of the financial return from reducing costs and improving productivity, this is called: a 69-year-old male with a history of alcohol abuse presents to the er after a month-long episode of headaches and confusion. based on his alcoholism, a likely cause of his neurologic symptoms is: _____ is the process of generating new and useful ideas concerning new products, services, manufacturing methods, and administrative processes. Hayden has $35 to spend on school supplies. he wants to buy notebooks, pencils, scissors, and a binder. if the total cost of the pencils and notebooks is greater than $16, which inequality represents the dollar amount, d, that Hayden can spend on the binder?(1) d < 19(2) d > 19(3) d < 51(4) d > 51