The reading on the 0 to 25 mm micrometer provided is
A. 15.20
B. 15.70
C. 15.45
D. 0.1520

In a p-n junction, option c is accurate because the  is double. the values below change if everything else stays the same and they only indicate a rise or fall in breakdown voltage.

Breakdown voltage It is the voltage at which current in a forward biased PN junction begins to flow or increases. When reverse voltage is present, junctions break down and reverse current increases quickly. The depletion layer's width narrows. The depletion layer becomes wider. A diode's breakdown voltage specifies the highest reverse voltage that can be used without exponentially increasing the leakage current in the diode. A diode won't necessarily be destroyed if its breakdown voltage is exceeded, but it will be if its current capacity is. To create an ionization path through the dielectric, the open gap voltage must increase before current can flow.

Learn more about breakdown voltage here:

https://brainly.com/question/29513692

#SPJ4

Simple switching between response options avoids a choice analysis because the distribution of behavior is constant.

The behavior of multiscale DPG particles in terms of distribution in porous media was observed using core scanning electron microscopy. The following are the precise test procedures: In order to calculate the pore volume and core permeability, the natural cores were taken, dried, and their dried weight was measured.

They were then saturated with water, and their wet weight was determined. The above-mentioned cores were removed and placed in a freeze dryer at -80°C for gelation for 24 hours; 1 PV of DPG particles (size of 2.2 m) were injected at a pump rate of 0.2 mL/min, and then left to stand at 90°C for aging for 5 days;  the frozen dried cores were crushed.

To know more about microscopy click here:

https://brainly.com/question/13504549

#SPJ4

Technician a is correct because he says that due to the cooling effect on pistons, diesel engine oil operates at higher temperatures than spark-ignition engine oil.

The diesel engine modeled after Rudolf Diesel is an example of a compression-ignition internal combustion engine, which ignites fuel by heating the air in the cylinder as a result of mechanical compression. Theoretically, diesel engines operate by compressing air to a high pressure and temperature, then injecting a small amount of fuel into the heated compressed air in cylinder. Due to the high temperature, the small amount of fuel that was injected and vigorously atomized evaporates.Diesel engines come in two different classes: two-stroke and four-stroke. Some bigger diesel engines operate on the two-stroke cycle, while most diesel engines utilize the four-stroke cycle. They generally have four or six in-line, direct-injection cylinders.

Learn more about diesel engine here:

https://brainly.com/question/1381153

#SPJ4

A curve should superelevate at a rate of 6%.A 10% maximum superelevation has been advised for highways with hills that are not snow-bound.

To learn more about Superelevation refer to:

https://brainly.com/question/29357625

#SPJ4

In the diagram shown, the process that is surface runoff is the surface labelled D.

Surface runoff is the flow of water happening on the ground surface when much rainwater, storm water, meltwater, or other sources, will no more sufficiently fast infiltrate in the soil. This is possible when the soil is exhausted by water to its full capacity, and the rain arrives more quickly than the soil can absorb it.

Therefore, the correct answer is as given above. That is, the surface tagged D depict the flow of water on the ground surface which is otherwise known as surface runoff.

learn more about surface runoff: https://brainly.com/question/29478956

#SPJ4

Az = 0, Ay = 8 kN, and MA = 21 kN m CCW are the reactions at a for the cantilever beam subjected to the distributed and concentrated loads.

The bending moment and moment reaction are equivalent at the cantilever beam's wall. The bending moment is 0 at the free end. The associated bending moment reaches its highest value at the point where the shear force crosses the zero axis.

And Kef f=3EI/L3x is the effective spring constant for a point force applied to the cantilever's end. The displacement at the end of the beam is w(x=Lx)=qL48EI, and the restoring force, Keffw, opposes the applied force.

To know more about cantilever visit:-

https://brainly.com/question/13254986

#SPJ4

The stopping distance is 4500 m/s

The distance travelled between the moment the body decides to stop a moving vehicle and the moment the vehicle comes to a complete stop is known as the stopping distance. The stopping distance, indicated by the letter d, is dependent on a number of variables, including as the road's surface and the driver's reflexes.

You must maintain a sufficient distance from the vehicle in front of you so that, if necessary, you can safely stop to avoid colliding with the vehicle.

Given ,

Initial velocity = 7000

That is half of intial velocity = 450

Stopping distance = 450*10

= 4500 m/s

Therefore the stopping distance is 4500 m/s

To learn more about stopping distance refer to :

https://brainly.com/question/24020960

#SPJ4

22  I-beams, 32 feet long and 5 end-plate boards 12 feet long.

The standard distance between deck joists is either 12 inches or 16 inches on center. (On-center refers to the distance between the centers of two joists rather than the distance between their edges.)

Subtract the width of your floor joist from the length of your floor: 32 -28

the total of the floor joists' on-center spacing divided by that difference  16"/4 = 4

To this value, add 1, then round the result to the next whole number:

22  I-beams, 32 feet long and 5 end-plate boards (e.g., 2x12s) 12 feet long.

To learn more about  floor joist refer to:

https://brainly.com/question/9477456

#SPJ1

The time taken is t = 259.04 sec will it take the transformation to go to 90% completion.

Johnson Mehl Avrami developed the Avrami equation, which is used to explain how crystalline solids change from one phase to another while maintaining a constant temperature. At constant temperature, solids change from one phase to another according to the Avrami equation. It can be applied broadly to various phase shifts in materials, such as chemical reaction rates, and can even be useful in assessments of ecological systems. It can particularly characterize the kinetics of crystallization. The Avrami equation gives us Y= 1 - e - Ktn, where Y = 50% T. Time of reaction completion is 148 seconds, and n = 1.8 is obtained by multiplying all values by 1. K \s 0.5=1- e^{-K*148^1.8} \s e^{-K*148^1.8} = 0.5

Taking both sides of the log

-K*148^{1.8} = -0.693 \s

K=8.59 * 10-5,

GIVEN THAT

0.85 = 1 - e

^{- 8.59 * 10^{-5} *t^1.8} \s e^{- 8.59 * 10^{-5} *t^1.8}

= 0.15

Taking the log on both sides: 8.59 x 10-5 t, t

= 259.04 sec,

t = -1.897 s

Learn more about system here-

https://brainly.com/question/19770086

#SPJ4

Apparently, some people claim that every signal may be described as a Fourier series, notably in electrical engineering and musical signal processing.

This prompted me to consider the mathematical justification for such an argument.

However, even after reading through various materials on the Fourier series (which I have little background in but understand the notion of), I was unable to locate a mathematical justification for the claim that every function can be represented by a Fourier series. The need for the function to be periodic was alluded to.

Most functions cannot be expressed as Fourier series, as may be seen by a simple counting argument. A countable family of Fourier coefficients serves as the basis for a Fourier series, and as a result, the set of such series has cardinality c0, as opposed to the set of real valued functions defined on some interval, which has cardinality cc.

To know more about functions click here:

https://brainly.com/question/9171028

#SPJ4

Using the information provided, 19.65 GPa is the maximum specific stiffness of the composite that can be calculated.

We provide;

Copper has a specific gravity of _cu = 8.9.

Tungsten has a specific gravity of 19.3 (_tu).

Copper's elasticity modulus is 110 GPa.

E tu = 407 GPa is the tungsten's elasticity modulus.

Tungsten volume fraction: V tu = 0.7

Copper volume percent, V cu = 0.3

1) The maximum rigidity permitted;

Let's use the formula to determine the modulus of elasticity's maximum value;

E u is equal to (E cu V cu) plus (E tu V tu).

E u = (110 × 0.3) + (407 × 0.7)

E u = 317.9 GPa

The formula yields an upper bound for the specific gravity;

(_cu V cu) + (_tu V tu) = _u

ρ u = (8.9 × 0.3) + (19.3 × 0.7)

ρ u = 16.18

E/u = Specific stiffness

Stiffness specific = 317.9/16.18

Specific stiffness upper limit = 19.65GPa

Learn more about specific here-

https://brainly.com/question/19819958

#SPJ4

Option b is correct. Gas in a cylinder expands against a piston from point a to point b on the p-v plot at the right. in this process the temperature decreases.

Think about a gas that is firmly sealed inside a vessel that has a moveable piston. By depressing the piston downward, we may manipulate the gas, and we can heat the gas by exposing the container to a flame or immersing it in a pot of boiling water. The pressure and volume of the gas can alter when we apply it to certain thermodynamic processes.

Using a PV diagram, also known as a pressure volume diagram, is an easy way to see these changes in the pressure and volume. On a PV diagram, each point represents a distinct gas condition. While the volume is indicated on the horizontal axis, the pressure is given on the vertical axis.

To know more about PV click here:

https://brainly.com/question/9466802

#SPJ4

BCD counters count using BCD numbers from 0000 to 1001 before looping back to 0000 and repeating the process.

Since a decimal digit is represented by a binary code with at least four bits and a MOD-10 count, such a counter must have at least four flip-flops to represent each digit. JK flip flops and a NAND gate are used to build the BCD or decade counter circuit. Since the BCD system is a 4-bit binary counter, its architecture is quite straightforward and only calls for four JK flip flops. The decade counter's design is depicted below. A counter like the one in the circuit above that has three flip-flops will then count from 0 to 7 or 2n-1.

Learn more about system here-

https://brainly.com/question/27162243

#SPJ4

The input resistance at the gate should be 10 M and the maximum signal swing at the drain is -0.8 v. A common-source amplifier's output resistance and common-gate amplifier's input resistance are the same.

The resistance between the input terminals with either input grounded is known as input resistance, or ri. If VP is grounded in Figure 13.3, then ri = RDRN. Depending on the kind of input, ri's value can range from 107 to 1012.

A 40 A change to the base current causes a 2 mA change to the collector current. With a load of 4 k, this transistor serves as a common-emitter amplifier.

To know more about  input resistance visit:-

https://brainly.com/question/29520222

#SPJ4

a) If the pipe rises at a 30° angle, the ranger station's maximum elevation, z, above the lake is 290 feet.

b) As we descend, the lake's pressure always rises. In comparison to point 2, point 3 has higher pressure. Because the rise in pressure is offset by the fall in datum, pump power remains constant for the same height, z=290 feet.

In the physical sciences, pressure is referred to as the stress at a point within a confined fluid or the perpendicular force per unit area. The force divided by the area over which it is exerted, or half a pound per square inch, determines the pressure that a 42-pound box with an area of 84 square inches at the bottom places on a floor.

Atmospheric pressure, which is roughly 15 pounds per square inch at sea level, is the amount of weight that the atmosphere exerts on each unit area of the Earth's surface. In SI units, pressure is expressed in pascals, where one pascal is equal to one newton per square meter. The atmosphere has a pressure of almost 100,000 pascals.

Learn more about pressure

https://brainly.com/question/945436

#SPJ4

Both technician a and technician b are correct that SLI battery' service life is significantly shortened by deeply discharging them, and that the thickness of the plates is the main difference between both batteries.

A lead-acid storage and rechargeable battery known as an SLI battery is primarily utilized in internal combustion engines for vehicles and other internal combustion powered devices. Simply put, SLI stands for starting, lighting, and ignition. It is intended to start, run, and maintain power supply. SLI batteries use thinner lead dioxide-filled plates instead of the thicker ones used in deep cycle batteries. As opposed to the higher current produced by an SLI battery, deep cycle batteries deliver a steady, lower current. Deep cycle batteries are made for repeated discharge and recharge in applications like RVs, golf carts, floor scrubbers, and electric vehicles. Generally speaking, deep cycle batteries shouldn't be discharged below 80% depth of discharge.

Learn more about SLI battery here:

https://brainly.com/question/28146138

#SPJ4

Both are true. Tech A claims that a vacuum gauge can be used to locate tiny vacuum leaks. According to tech B, the catalytic converter is usually placed behind the muffler.

Tailpipe. The catalytic converter has cleaned up the exhaust gases, which are then sent out of the car and into the atmosphere via the tailpipe, the last link in the exhaust system.

Hazardous pollutants from engine exhaust are decreased by the catalytic converter. The converter, which is situated between the exhaust manifold and the muffler, works with heat and metals that serve as catalysts.

To know more about vacuum gauge visit:-

https://brainly.com/question/20989381

#SPJ4

The statement that are fundamental intuitions behind collaborative filtering is Only A. The fundamental intuition behind collaborative filtering are similar users will rate the items similarly.

To point some of the limitations of content-based filtering, collaborative filtering uses similarities between users and items simultaneously to provide recommendations. The example of collaborative filtering is collaborative filtering give the recommendation system as preferences in television programming could analyze about which television show a user should like given a partial list of that user's tastes (likes or dislikes). There are two main kind of Collaborative Filtering:

Learn more about the collaborative filtering here, https://brainly.com/question/14747907

#SPJ4

Steel is the emaerial used because it is stated that the floor is made of steel. Any material, such as wood, steel, or composite, may be used for roof framing.

Primary elements are the main member in floor system which transfer the load coming on to the element from secondary beam elemnts.The main beams will be joined to the building's columns. The two most common shapes are H and W sections. Secondary elements, which span between principal beams, often accept the slab's weight before passing it on to the primary elemnts. The primary components are joined to the secondary beams for load transfer. Secondary elements are seldom ever employed. If employed, they function as a load transfer system from the slab to the secondary element or as a means of strengthening the floor system to lessen deflection. The top chord and bottom tie members are the main components of roof framing. The weight is transferred from the purlins to the columns or wall via these elements. often have a double-angle or channel section. Tie and the chord member between the top are secondary components.Ther are subjected to compression and tension and transfer forces to the primary elements.

Learn more about roof framing here:

https://brainly.com/question/14799449

#SPJ4

Map Reduce refers to a programming model used within Hadoop that performs the two major steps for which it is named: the map step and the reduce step.

To learn more about MapReduce refer :

https://brainly.com/question/14571523

#SPJ4

Freight forwarder is the party that facilitates the movement of cargo to the international destination on behalf of shippers and processes the documentation or performance activities related to those shipments.

A company that specializes in organizing goods on behalf of shippers is known as a freight forwarder.

Freight forwarders typically offer a range of supply chain services, such as: Ocean or air freight transport. from the point of origin to the point of destination by land. A freight forwarder plans shipments for businesses or individuals. The break-bulk and distribution of cargoes are handled by freight forwarders, who also assemble and combine goods. Freight forwarders, as opposed to brokers, take charge of the transportation and sometimes even move the freight themselves. The main distinction is that a freight forwarder will assume responsibility for transportation both to and from ports.

Learn more about Cargoes here-

https://brainly.com/question/14603564

#SPJ4

The calculated answer is 90 L atm, a pure gas made up only of atoms. The noble gases argon, krypton, and xenon are some examples.

Consider a monatomic perfect gas with m-mean particles that don't interact and a resting mass center. An ion with only one atom is referred to as a monatomic ion or simple ion. A polyatomic ion is one that has more than one atom, even if they are all from the same element.

From the information provided:

The first route:

A (1 atm, 20 L), C (3 atm), and D (1 atm, 50 L)

The second route:

A (3 atm, 50 L), B (3 atm, 20 L), and D ( 1 atm, 50 L)

Because one mole equals one mole,

to locate wAB;

The conversion is depicted as A B occurring under constant pressure.

∴

Pressure x Volume Change = wAB

V2 - V1 = wAB

atm = wAB ( 50 L - 20 L)

atm = wAB ( 30 L)

wAB=90 L.atm

Learn more about monoatomic here-

https://brainly.com/question/19865411

#SPJ4

Set up the Windows 2000 workstations' VLAN membership so that they are on their own VLAN.

As the gateway to a wide area network (WAN) or the Internet, the core switch is also regarded as a backbone component that is essential to the smooth operation of a network. We can use it to connect to servers, our Internet service provider (ISP), via a router, and to aggregate all switches. When a client submits a request, a load balancer receives it and distributes it to various servers. Distributing client requests evenly among several servers is one objective of load balancing, which also aims to boost performance.

Learn more about operation here-

https://brainly.com/question/27960749

#SPJ4

Option A is correct. Only a strong magnetic field has the power to magnetize it. But after being magnetized, steel has the capacity to hold onto its magnetic properties.

Steel is suitable for use in permanent magnets thanks to this property. Since paperclips are not magnetic by nature, they cannot be chained together on their own. The paperclips can, however, be momentarily magnetic by employing a magnet. A paper clip's steel can be easily magnetic, but it quickly loses its magnetism. Steel wire is typically used to make paper clips. Steel is an iron and carbon alloy. Magnets are drawn to iron because it is a ferromagnetic material.

Learn more about steel here-

https://brainly.com/question/22573226

#SPJ4

Answer: A

Explanation:

The part's net radiation heat transfer rate, expressed as a rate per unit length, isQ=123.4Kw/m

Given

temperature of 925 K

diameter of 2 m

we know that F11+f12+f13=1

F11+F13=1

so

F11=F13=0.5

A1F13=A3F31

=2L*1*0.5

2*1*1*0.5

A1F13=1

Similary F23 =1

A3F32=2

Therefore

A1F13=1

A3F32=2

T3=925k

T1=T2=300k

Q=1*σ*(925⁴-300⁴)+2*σ*(925⁴-300⁴)

=3*σ*(925⁴-300⁴)

=3*5.67*10⁻⁸*(925⁴-300⁴)

Therefore net radiation heat transfer rate

Q=123.4Kw/m

Learn more about radiation here:

https://brainly.com/question/13934832

#SPJ4

Based on their forms, the 206 bones that make up the adult skeleton are separated into five groups. Each bone's category shape has a certain function due to the relationship between its shapes and functions.

An object with a long bone has a cylindrical shape and is longer than it is wide. But keep in mind that the phrase refers to a bone's form, not its size.

A short bone is one that is roughly equal in length, width, and thickness and has a cube-like shape. The carpals in the wrists and the tarsals in the ankles are the only short bones in the human skeleton.

Although a flat bone is often thin, it is also sometimes curved, so the phrase "flat bone" is somewhat misleading.

A bone is considered irregular if it lacks an obviously identifiable shape and so does not fall under another category.

A sesamoid bone is a tiny, round bone that resembles a sesame seed, as the name implies. These bones develop in tendons, the tissue sheaths that connect bones to muscles, where a lot of joint pressure is produced.

To know more about bone click here:

https://brainly.com/question/14810294

#SPJ4

With a pressure drop of 120 kpa/m, glycerin at 380 c flows through a horizontal pipe with a 9 mm diameter. The Reynolds number is 3.807 after the discharge.

pressure drop=32μVL/D²

120*10³=32*0.95*V*1/(9*10⁻³)²

Velocity V=0.329 m/sec

discharge =AV

=π(9*10⁻³)²/4*0.319

pressure drop=2.02*10⁻⁵ m³

then,

Reynolds number=VD/γ

=δVD/μ

1.26*10³*0.319*9*10⁻³/0.95

=3.807

By measuring the proportion of inertial and viscous forces, the Reynolds number aids in the prediction of flow patterns in various fluid flow scenarios. Laminar flow typically predominates in low Reynolds numbers flows while turbulent flow predominates in high Reynolds numbers flows.

Learn more about Reynolds number here:

https://brainly.com/question/12977616

#SPJ4

It is to be noted that from the code snippet, since the clock changes every 10-time units, has a half cycle of 10 seconds, therefore the period is 20 units.  

A clock with a half cycle of 10 seconds and a period of 20-time units would have a half cycle of 10 seconds and a period of 20-time units. A clock that changes every 10 seconds, for example, would have a half cycle of 10 seconds.

As a result, the accuracy is 1ns and the time unit is 10ns. To retrieve the actual simulation time, multiply the time unit by the delay set with #, which is then rounded down based on accuracy. The first delay statement returns 10ns, whereas the second delay statement returns 14.9, which is rounded to 15ns.

Note that a snippet is a tiny area of reusable source code, machine code, or text in programming. These are often explicitly specified operational units that are included in bigger programming modules. Some text editors, computer source code editors, IDEs, and related tools provide snippet management.

Learn more about code snippets:
https://brainly.com/question/15003151
#SPJ1

Engineers may create diesel engines with higher compression ratios than gasoline engines because diesel has a higher compression resistance and is denser than light distillate fuels.

The thermal efficiency of an engine increases with increasing compression ratio. Shaker, circulation, and spray jet systems are three ways that engine oil is utilized to assist in cooling pistons. the diesel engine. a fuel-burning engine that runs on diesel. Fuel oil is directly injected into the cylinders of a diesel engine. The air itself is hot enough to ignite the diesel fuel without a spark due to the extreme compression. Cycle with four strokes.

Learn more about system here-

https://brainly.com/question/27162243

#SPJ4

Answer:

Inventory Planner

Explanation:

An inventory planner is a specialist that is in charge of developing efficient inventory plans and strategies to enhance an organization's profitability. Inventory planners must create paperwork outlining the quantity specifications of the organization's goods or equipment.