The diameter of a cylindrical water tank is Do and its height is H. The tank is filled with water, which is open to the atmosphere. An orifice of diameter D with a smooth entrance (i.e., negligible losses) is open at the bottom. Develop a relation for the time required for the tank (a) to empty halfway (5-point) and (b) to empty completely (5-point).

Answer:

a. The time required for the tank to empty halfway is presented as follows;

[tex]t_1 = \dfrac{D_0^2 }{D^2 } \cdot \sqrt{ \dfrac{H}{g} } \cdot \left (\sqrt{2} -1 \right)[/tex]

b. The time it takes for the tank to empty the remaining half is presented as follows;

[tex]t_2 = { \dfrac{ D_0^2 }{D} \cdot\sqrt{\dfrac{H}{g} }[/tex]

The total time 't', is presented as follows;

[tex]t = \sqrt{2} \cdot \dfrac{D_0^2 }{D^2 } \cdot \sqrt{ \dfrac{H}{g} }[/tex]

Explanation:

a. The diameter of the tank = D₀

The height of the tank = H

The diameter of the orifice at the bottom = D

The equation for the flow through an orifice is given as follows;

v = √(2·g·h)

Therefore, we have;

[tex]\dfrac{P_1}{\gamma} + z_1 + \dfrac{v_1}{2 \cdot g} = \dfrac{P_2}{\gamma} + z_2 + \dfrac{v_2}{2 \cdot g}[/tex]

[tex]\left( \dfrac{P_1}{\gamma} -\dfrac{P_2}{\gamma} \right) + (z_1 - z_2) + \dfrac{v_1}{2 \cdot g} = \dfrac{v_2}{2 \cdot g}[/tex]

Where;

P₁ = P₂ = The atmospheric pressure

z₁ - z₂ = dh (The height of eater in the tank)

A₁·v₁ = A₂·v₂

v₂ = (A₁/A₂)·v₁

A₁ = π·D₀²/4

A₂ = π·D²/4

A₁/A₂ = D₀²/(D²) = v₂/v₁

v₂ = (D₀²/(D²))·v₁ = √(2·g·h)

The time, 'dt', it takes for the water to drop by a level, dh, is given as follows;

dt = dh/v₁ = (v₂/v₁)/v₂·dh = (D₀²/(D²))/v₂·dh = (D₀²/(D²))/√(2·g·h)·dh

We have;

[tex]dt = \dfrac{D_0^2}{D} \cdot\dfrac{1}{\sqrt{2\cdot g \cdot h} } dh[/tex]

The time for the tank to drop halfway is given as follows;

[tex]\int\limits^{t_1}_0 {} \, dt = \int\limits^h_{\frac{h}{2} } { \dfrac{D_0^2}{D} \cdot\dfrac{1}{\sqrt{2\cdot g \cdot h} } } \, dh[/tex]

[tex]t_1 =\left[{ \dfrac{D_0^2}{D\cdot \sqrt{2\cdot g} } \cdot\dfrac{h^{-\frac{1}{2} +1}}{-\frac{1}{2} +1 } \right]_{\frac{H}{2} }^{H} =\left[ { \dfrac{D_0^2 \cdot 2\cdot \sqrt{h} }{D\cdot \sqrt{2\cdot g} } \right]_{\frac{H}{2} }^{H} = { \dfrac{2 \cdot D_0^2 }{D\cdot \sqrt{2\cdot g} } \cdot \left(\sqrt{H} - \sqrt{\dfrac{H}{2} } \right)[/tex]

[tex]t_1 = { \dfrac{2 \cdot D_0^2 }{D^2\cdot \sqrt{2\cdot g} } \cdot \left(\sqrt{H} - \sqrt{\dfrac{H}{2} } \right) = { \dfrac{\sqrt{2} \cdot D_0^2 }{D^2\cdot \sqrt{ g} } \cdot \left(\sqrt{H} - \sqrt{\dfrac{H}{2} } \right)[/tex]

[tex]t_1 = { \dfrac{\sqrt{2} \cdot D_0^2 }{D^2\cdot \sqrt{ g} } \cdot \left(\sqrt{H} - \sqrt{\dfrac{H}{2} } \right) = { \dfrac{D_0^2 }{D^2\cdot \sqrt{ g} } \cdot \left(\sqrt{2 \cdot H} - \sqrt{{H} } \right) =\dfrac{D_0^2 }{D^2 } \cdot \sqrt{ \dfrac{H}{g} } \cdot \left (\sqrt{2} -1 \right)[/tex]The time required for the tank to empty halfway, t₁, is given as follows;

[tex]t_1 = \dfrac{D_0^2 }{D^2 } \cdot \sqrt{ \dfrac{H}{g} } \cdot \left (\sqrt{2} -1 \right)[/tex]

(b) The time it takes for the tank to empty completely, t₂, is given as follows;

[tex]\int\limits^{t_2}_0 {} \, dt = \int\limits^{\frac{h}{2} }_{0 } { \dfrac{D_0^2}{D} \cdot\dfrac{1}{\sqrt{2\cdot g \cdot h} } } \, dh[/tex]

[tex]t_2 =\left[{ \dfrac{D_0^2}{D\cdot \sqrt{2\cdot g} } \cdot\dfrac{h^{-\frac{1}{2} +1}}{-\frac{1}{2} +1 } \right]_{0}^{\frac{H}{2} } =\left[ { \dfrac{D_0^2 \cdot 2\cdot \sqrt{h} }{D\cdot \sqrt{2\cdot g} } \right]_{0 }^{\frac{H}{2} } = { \dfrac{2 \cdot D_0^2 }{D\cdot \sqrt{2\cdot g} } \cdot \left( \sqrt{\dfrac{H}{2} } -0\right)[/tex]

[tex]t_2 = { \dfrac{ D_0^2 }{D} \cdot\sqrt{\dfrac{H}{g} }[/tex]

The time it takes for the tank to empty the remaining half, t₂, is presented as follows;

[tex]t_2 = { \dfrac{ D_0^2 }{D} \cdot\sqrt{\dfrac{H}{g} }[/tex]

The total time, t, to empty the tank is given as follows;

[tex]t = t_1 + t_2 = \dfrac{D_0^2 }{D^2 } \cdot \sqrt{ \dfrac{H}{g} } \cdot \left (\sqrt{2} -1 \right) + t_2 = { \dfrac{ D_0^2 }{D} \cdot\sqrt{\dfrac{H}{g} } = \dfrac{D_0^2 }{D^2 } \cdot \sqrt{ \dfrac{H}{g} } \cdot \sqrt{2}[/tex]

[tex]t = \sqrt{2} \cdot \dfrac{D_0^2 }{D^2 } \cdot \sqrt{ \dfrac{H}{g} }[/tex]

Which option identifies the section of a project charter represented in the following scenario?
Updated POS terminals will be available to the following five departments by July 31, 2015.
O project assumptions
O project deliverables
O project constraints
O project requirements

Match the example to the model type it represents.

1. The client complains about the way the keyboard feels
1.mock-up
2. The engineering team tests how the tire treads on a new SUV perform on 2.various road conditions
preproduction model
3. The engineering team performs tests on the efficiency of the manufacturing process used for a recumbent bicycle
3.presentation model

An infinite cylindrical rod falls down in the middle of an infinite tube filled with fluidat a constant speed V (terminal velocity). The density of the rod and the fluid are different.Assume that the pressure field is hydrostatic.(a)[5pts] Solve for the velocity profileas a function of rin terms of V and the other variables.(b)[2pts] Calculate upward force per unit length of the rod from the fluid wall shear stress on the rod.(c)[2 pts] Calculate upward force per unit length of the rod from bouyancy.(d)[1pts] Calculate V.VR1

Choose two other elements from the periodic table that you predict should react to form something like table salt


Please pleassssss helppp

I give branlistttttt

A utility generates electricity with a 36% efficient coal-fired power plant emitting the legal limit of 0.6 lb of SO2 per million Btus of heat into the plant. Suppose the utility encourages its customers to replace their 75-W incandescents with 18-W compact fluorescent lamps (CFLs) that produce the same amount of light. Over the 10,000-hr lifetime of a single CFL.

Required:
a. How many kilowatt-hours of electricity would be saved?
b. How many 2,000-lb tons of SO2 would not be emitted?
c. If the utility can sell its rights to emit SO2 at $800 per ton, how much money could the utility earn by selling the SO2 saved by a single CFL?

(SI units) Molten metal is poured into the pouring cup of a sand mold at a steady rate of 400 cm3/s. The molten metal overflows the pouring cup and flows into the downsprue. The cross section of the sprue is round, with a diameter at the top = 3.4 cm. If the sprue is 20 cm long, determine the proper diameter at its base so as to main- tain the same volume flow rate.

Shorter lines are faster than longer lines is an example of an algorithm.

Find the minimum stages at total reflux for separating ethanol-acetone mixture to achieve 95 mol% purity of acetone in the distillate and 95 mol% purity of ethanol in the bottoms product. Use equilibrium data from problem 4D7. x y Equilibrium data for acetone (A) and ethanol at 1 atm (Perry et al., 1963, pp. 13-4) are
0.100.150.200.250.300.350.40 0.50 0.60 0.70 0.80 0.90 0.262 0.348 0.417 0.478 0.524 0.566 0.605 0.674 0.739 0.80 20.865 0.929

Write a python program to get the following output. 1-----99 2-----98 3-----97 . . . . . . 98-----2 99-----1

Determine the maximum shear stress in the beam and the minimum yield strength that should be considered to obtain a minimum factor of safety of 2 based on the distortion-energy theory. The maximum shear stress in the beam is 1875 Numeric ResponseEdit Unavailable. 1875 correct.psi. The minimum yield strength based on the distortion-energy theory is

Many households in developing countries prepare food over indoor cook stoves with no ducting system to exhaust the combustion products outside. A woman in a household lights a fire in her cookstove at 4 pm. The fire emits benzo(a)pyrene, a carcinogenic compound, at a rate of 0.01 ng/min. The house has a size of 40 m3 and a ventilation rate of 1 m3/h. The ambient indoor air concentration of benzo(a)pyrene was 0.2 ng/m3 when she started the fire, but no significant concentration of benzo(a)pyrene is found in the outdoor air. What is the indoor benzo(a)pyrene concentration in the household at 6 pm?

A cylindrical specimen of some metal alloy 10 mm in diameter and 150 mm long has a modulus of elasticity of 100 GPa. Does it seem reasonable to expect a tensile stress of 200 MPa to produce a reduction in specimen diameter of 0.08 mm

What's the ampacity of a No. 10 type TW copper Wire in a raceway containing six wires and located in an area where the ambient Temperature is 50 C

A. 15.1 A
B. 8.6 A
C. 13.9 A
D. 10.8 A

A water jet pump involves a jet cross-sectional area of 0.01 m^2, and a jet velocity of 30 m/s. The jet is surrounded by entrained water. The total cross-sectional area associated with the jet and entrained streams is 0.075 m^2. These two fluid streams leave the pump thoroughly mixed with an average velocity of 6 m/s through a cross-sectional area of 0.075 m^2. Determine the pumping rate (i.e., the entrained fluid flowrate) involved in liters/s.

The output of a first order transducer is to be connected to a signal conditioner which also has first order dynamic characteristics. The transducer has known time constant of x milliseconds and static sensitivity of xx V/kPa while the signal conditioner has a time constant of y milliseconds and a static sensitivity of yy V/V. Determine the steady state response of this measurement system to an input signal of the form: P(t)=(A+B*sin(w*t) ) kPa.

Determine the convection heat transfer coefficient, thermal resistance for convection, and the convection heat transfer rate that are associated with air at atmospheric pressure in cross flow over a cylinder of diameter D = 100 mm and length L = 2 m. The cylinder temperature is Ts = ° 70 C while the air velocity and temperature are V = 3 m/s and T[infinity] = 20°C, respectively. Plot the convection heat transfer coefficient and the heat transfer rate from the cylinder over the range 0.05 m ≤ D ≤ 0.5 m.

Kim is working on the cost estimate and feasible design options for a building. Which stage of a construction plan is Kim working on now? A. design development B. schematic design C. mechanical D. structural