Your friend should stand approximately 1.565 meters (or 1565 mm) away from the camera to produce a 43 mm tall image on the light sensor. This answer is obtained by rounding off the decimal to three significant figures
To calculate the distance your friend should stand in order to produce a 43 mm tall image on the light sensor, the following formula can be used: Image Height/Object Height = Distance/ Focal Length
The image height is given as 43 mm, the object height is 1.8 m, the focal length is 65 mm. Substituting these values in the formula, we get
:43/1800 = Distance/65Cross multiplying,65 x 43 = Distance x 1800
Therefore,Distance = (65 x 43)/1800 = 1.565
Therefore, your friend should stand approximately 1.565 meters (or 1565 mm) away from the camera to produce a 43 mm tall image on the light sensor. This answer is obtained by rounding off the decimal to three significant figures
.Note: The given light sensor size of the digital camera (15.2 mm × 23.4 mm) is not relevant to the calculation of the distance your friend should stand from the camera.
To learn more about camera visit;
https://brainly.com/question/31845942
#SPJ11
An ice dancer with her arms stretched out starts into a spin with an angular velocity of 2.2 rad/s. Her moment of inertia with her arms stretched out is 2.74kg m? What is the difference in her rotational kinetic energy when she pulls in her arms to make her moment of inertia 1.54 kg m2?
The difference in rotational kinetic energy when the ice dancer pulls in her arms from a moment of inertia of 2.74 kg m² to 1.54 kg m² is 0.998 Joules.
When the ice dancer pulls in her arms, her moment of inertia decreases, resulting in a change in rotational kinetic energy. The formula for the difference in rotational kinetic energy (ΔK) is given by ΔK = ½ * (I₂ - I₁) * (ω₂² - ω₁²), where I₁ and I₂ are the initial and final moments of inertia, and ω₁ and ω₂ are the initial and final angular velocities.
Given I₁ = 2.74 kg m², I₂ = 1.54 kg m², and ω₁ = 2.2 rad/s, we can calculate ω₂ using the conservation of angular momentum, I₁ * ω₁ = I₂ * ω₂. Solving for ω₂ gives ω₂ = (I₁ * ω₁) / I₂.
Substituting the values into the formula for ΔK, we have ΔK = ½ * (I₂ - I₁) * [(I₁ * ω₁ / I₂)² - ω₁²].
Performing the calculations, we find ΔK ≈ 0.998 Joules. This means that when the ice dancer pulls in her arms, the rotational kinetic energy decreases by approximately 0.998 Joules.
Learn more about angular velocities. from the given link
https://brainly.com/question/30237820
#SPJ11
In a Young's double-slit experiment the wavelength of light used is 472 nm (in vacuum), and the separation between the slits is 1.7 × 10-6 m. Determine the angle that locates (a) the dark fringe for which m = 0, (b) the bright fringe for which m = 1, (c) the dark fringe for which m = 1, and (d) the bright fringe for which m = 2.
Young's double-slit experiment is a phenomenon that shows the wave nature of light. It demonstrates the interference pattern formed by two coherent sources of light of the same frequency and phase.
The angle that locates the (a) dark fringe is 0.1385°, (b) bright fringe is 0.272°, (c) dark fringe is 0.4065°, and (d) bright fringe is 0.5446°.
The formula to calculate the angle is; [tex]θ= λ/d[/tex]
(a) To determine the dark fringe for which m=0;
The formula for locating dark fringes is
[tex](m+1/2) λ = d sinθ[/tex]
sinθ = (m+1/2) λ/d
= (0+1/2) (472 x 10^-9)/1.7 × 10^-6
sinθ = 0.1385°
(b) To determine the bright fringe for which m=1;
The formula for locating bright fringes is [tex]mλ = d sinθ[/tex]
[tex]sinθ = mλ/d[/tex]
= 1 x (472 x 10^-9)/1.7 × 10^-6
sinθ = 0.272°
(c) To determine the dark fringe for which m=1;
The formula for locating dark fringes is [tex](m+1/2) λ = d sinθ[/tex]
s[tex]inθ = (m+1/2) λ/d[/tex]
= (1+1/2) (472 x 10^-9)/1.7 × 10^-6
sinθ = 0.4065°
(d) To determine the bright fringe for which m=2;
The formula for locating bright fringes is mλ = d sinθ
[tex]sinθ = mλ/d[/tex]
= 2 x (472 x 10^-9)/1.7 × 10^-6
sinθ = 0.5446°
Thus, the angle that locates the (a) dark fringe is 0.1385°, (b) bright fringe is 0.272°, (c) dark fringe is 0.4065°, and (d) bright fringe is 0.5446°.
To learn more about frequency visit;
https://brainly.com/question/29739263
#SPJ11
A 1.0 kQ resistor is connected to a 1.5 V battery. The current
through the resistor is equal to a.1.5mA
b 1.5KA
d1.5A
c 1.5 μA
The correct answer is (d) 1.5 A.
The current through a resistor connected to a battery can be calculated using Ohm's Law, which states that the current (I) flowing through a resistor is equal to the voltage (V) across the resistor divided by its resistance (R). Mathematically, it can be expressed as I = V/R.
In this case, the voltage across the resistor is given as 1.5 V, and the resistance is 1.0 kΩ (which is equivalent to 1000 Ω). Plugging these values into Ohm's Law, we get I = 1.5 V / 1000 Ω = 0.0015 A = 1.5 A.
Therefore, the current through the 1.0 kΩ resistor connected to the 1.5 V battery is 1.5 A.
To know more about resistor click here: brainly.com/question/30672175
#SPJ11
An electron is measured to have a momentum 68.1 +0.83 and to be at a location 7.84mm. What is the minimum uncertainty of the electron's position (in nm)? D Question 11 1 pts A proton has been accelerated by a potential difference of 23kV. If its positich is known to have an uncertainty of 4.63fm, what is the minimum percent uncertainty (x 100) of the proton's P momentum?
The minimum percent uncertainty of the proton's momentum is 49.7%.
Momentum of an electron = 68.1 ± 0.83
Location of an electron = 7.84 mm = 7.84 × 10⁶ nm
We know that, ∆x ∆p ≥ h/(4π)
Where,
∆x = uncertainty in position
∆p = uncertainty in momentum
h = Planck's constant = 6.626 × 10⁻³⁴ Js
Putting the given values,
∆x (68.1 ± 0.83) × 10⁻²⁷ ≥ (6.626 × 10⁻³⁴) / (4π)
∆x ≥ h/(4π × ∆p) = 6.626 × 10⁻³⁴ /(4π × (68.1 + 0.83) × 10⁻²⁷)
∆x ≥ 2.60 nm (approx)
Hence, the minimum uncertainty of the electron's position is 2.60 nm.
A proton has been accelerated by a potential difference of 23 kV. If its position is known to have an uncertainty of 4.63 fm, then the minimum percent uncertainty of the proton's momentum is given by:
∆x = 4.63 fm = 4.63 × 10⁻¹⁵ m
We know that the de-Broglie wavelength of a proton is given by,
λ = h/p
Where,
λ = de-Broglie wavelength of proton
h = Planck's constant = 6.626 × 10⁻³⁴ J.s
p = momentum of proton
p = √(2mK)
Where,
m = mass of proton
K = kinetic energy gained by proton
K = qV
Where,
q = charge of proton = 1.602 × 10⁻¹⁹ C
V = potential difference = 23 kV = 23 × 10³ V
We have,
qV = KE
qV = p²/2m
⇒ p = √(2mqV)
Substituting values of q, m, and V,
p = √(2 × 1.602 × 10⁻¹⁹ × 23 × 10³) = 1.97 × 10⁻²² kgm/s
Now,
λ = h/p = 6.626 × 10⁻³⁴ / (1.97 × 10⁻²²) = 3.37 × 10⁻¹² m
Uncertainty in position is ∆x = 4.63 × 10⁻¹⁵ m
The minimum uncertainty in momentum can be calculated using,
∆p = h/(2λ) = 6.626 × 10⁻³⁴ / (2 × 3.37 × 10⁻¹²) = 0.98 × 10⁻²² kgm/s
Minimum percent uncertainty in momentum is,
∆p/p × 100 = (0.98 × 10⁻²² / 1.97 × 10⁻²²) × 100% = 49.74% = 49.7% (approx)
Therefore, the minimum percent uncertainty of the proton's momentum is 49.7%.
To learn more about momentum, refer below:
https://brainly.com/question/30677308
#SPJ11
"For
a converging lens with a 25.0cm focal length, an object with a
height of 6cm is placed 30.0cm to the left of the lens
a. Draw a ray tracing diagram of the object and the resulting
images
A ray tracing diagram is shown below:
Ray tracing diagram of the object and resulting image for a converging lens
Focal length of converging lens, f = 25.0 cm
Height of the object, h = 6 cm
Distance of the object from the lens, u = -30.0 cm (negative as the object is to the left of the lens)
We can use the lens formula to calculate the image distance,
v:1/f = 1/v - 1/u1/25 = 1/v - 1/-30v = 83.3 cm (approx.)
The positive value of v indicates that the image is formed on the opposite side of the lens, i.e., to the right of the lens. We can use magnification formula to calculate the height of the image,
h':h'/h = -v/uh'/6 = -83.3/-30h' = 20 cm (approx.)
Therefore, the image is formed at a distance of 83.3 cm from the lens to the right side, and its height is 20 cm.
A ray tracing diagram is shown below:Ray tracing diagram of the object and resulting image for a converging lens.
Learn more about converging lens https://brainly.com/question/15123066
#SPJ11
2 -14 Points DETAILS OSCOLPHYS2016 13.P.01. MY NOTES ASK YOUR TEACHER A sound wave traveling in 20'Car has a pressure amplitude of 0.0 What intensity level does the sound correspond to? (Assume the density of ar 1.23 meter your answer.) db
The intensity level (I_dB) is -∞ (negative infinity).
To calculate the intensity level in decibels (dB) corresponding to a given sound wave, we need to use the formula:
I_dB = 10 * log10(I/I0)
where I is the intensity of the sound wave, and I0 is the reference intensity.
Given:
Pressure amplitude (P) = 0.0 (no units provided)
Density of air (ρ) = 1.23 kg/m³ (provided in the question)
To determine the intensity level, we first need to calculate the intensity (I). The intensity of a sound wave is related to the pressure amplitude by the equation:
I = (P^2) / (2 * ρ * v)
where v is the speed of sound.
The speed of sound in air at room temperature is approximately 343 m/s.
Plugging in the given values and calculating the intensity (I):
I = (0.0^2) / (2 * 1.23 kg/m³ * 343 m/s)
I = 0 / 846.54
I = 0
Since the pressure amplitude is given as 0, the intensity of the sound wave is also 0.
Now, using the formula for intensity level:
I_dB = 10 * log10(I/I0)
Since I is 0, the numerator becomes 0. Therefore, the intensity level (I_dB) is -∞ (negative infinity).
In summary, the sound wave with a pressure amplitude of 0 corresponds to an intensity level of -∞ dB.
To know more about intensity level refer here: https://brainly.com/question/30101270#
#SPJ11
a heat engine exhausts 22,000 J of energy to the envioement while operating at 46% efficiency.
1. what is the heat input?
2. this engine operates at 68% of its max efficency. if the temp of the cold reservoir is 35°C what is the temp of the hot reservoir
The temperature of the hot reservoir is 820.45°C.Given data:Amount of energy exhausted, Q
out = 22,000 J
Efficiency, η = 46%1. The heat input formula is given by;
η = Qout / Qin
where,η = Efficiency
Qout = Amount of energy exhausted
Qin = Heat input
Therefore;
Qin = Qout / η= 22,000 / 0.46= 47,826.09 J2.
The efficiency of the engine at 68% of its maximum efficiency is;
η = 68% / 100%
= 0.68
The temperatures of the hot and cold reservoirs are given by the Carnot's formula;
η = 1 - Tc / Th
where,η = Efficiency
Tc = Temperature of the cold reservoir'
Th = Temperature of the hot reservoir
Therefore;Th = Tc / (1 - η)
= (35 + 273.15) K / (1 - 0.68)
= 1093.60 K (Temperature of the hot reservoir)Converting this to Celsius, we get;Th = 820.45°C
Therefore, the temperature of the hot reservoir is 820.45°C.
To know more about temperature visit:
https://brainly.com/question/7510619
#SPJ11
A cube with edges of length 1 = 0.13 m and density Ps = 2.7 x 103kg/m3 is suspended from a spring scale. a. When the block is in air, what will be the scale reading?
"When the cube is in air, the scale reading will be approximately 58.24 N." Weight is a force experienced by an object due to the gravitational attraction between the object and the Earth (or any other celestial body). It is a vector quantity, meaning it has both magnitude and direction. The weight of an object is directly proportional to its mass and the acceleration due to gravity.
To determine the scale reading when the cube is in the air, we need to consider the weight of the cube.
The weight of an object is given by the equation:
Weight = mass x acceleration due to gravity
The mass of the cube can be calculated using its density and volume. Since it is a cube, each side has a length of 0.13 m, so the volume is:
Volume = length^3 = (0.13 m)³ = 0.002197 m³
The mass is then:
Mass = density x volume = (2.7 x 10³ kg/m³) x 0.002197 m³ = 5.9449 kg
The acceleration due to gravity is approximately 9.8 m/s².
Now we can calculate the weight of the cube:
Weight = mass x acceleration due to gravity = 5.9449 kg x 9.8 m/s²= 58.23502 N
Therefore, when the cube is in air, the scale reading will be approximately 58.24 N.
To know more about weight & mass visit:
https://brainly.com/question/86444
#SPJ11
In a Photoelectric effect experiment, the incident photons each has an energy of 5.162×10−19 J. The power of the incident light is 0.74 W. (power = energy/time) The work function of metal surface used is W0 =2.71eV.1 electron volt (eV)=1.6×10−19 J. If needed, use h=6.626×10−34 J⋅s for Planck's constant and c=3.00×108 m/s for the speed of light in a vacuum. Part A - How many photons in the incident light hit the metal surface in 3.0 s Part B - What is the max kinetic energy of the photoelectrons? Part C - Use classical physics fomula for kinetic energy, calculate the maximum speed of the photoelectrons. The mass of an electron is 9.11×10−31 kg
The maximum speed of the photoelectrons is 1.355 × 10^6 m/s.
The formula for energy of a photon is given by,E = hf = hc/λ
where E is the energy of a photon, f is its frequency, h is Planck's constant, c is the speed of light, and λ is the wavelength. For this question,
h = 6.626 × 10^-34 J s and
c = 3.00 × 10^8 m/s .
Part A
The energy of each incident photon is 5.162×10−19 J
The power of the incident light is 0.74 W.
The total number of photons hitting the metal surface in 3.0 s is calculated as:
Energy of photons = Power × Time => Energy of 1 photon × Number of photons = Power × Time
So,
Number of photons = Power × Time/Energy of 1 photon
Therefore, Number of photons = 0.74 × 3.0 / 5.162 × 10^-19 = 4293.3 ≈ 4293.
Thus, 4293 photons in the incident light hit the metal surface in 3.0 s.
Part B
The energy required to remove an electron from the metal surface is known as the work function of the metal.
The work function W0 of the metal surface used is 2.71 eV = 2.71 × 1.6 × 10^-19 J = 4.336 × 10^-19 J.
Each photon must transfer at least the energy equivalent to the work function to the electron. The maximum kinetic energy of the photoelectrons is given by:
KE
max = Energy of photon - Work function KE
max = (5.162×10−19 J) - (2.71 × 1.6 × 10^-19 J) = 0.822 × 10^-18 J.
Thus, the max kinetic energy of the photoelectrons is 0.822 × 10^-18 J.
Part C
The maximum speed vmax of the photoelectrons is given by the classical physics formula for kinetic energy, which is:
KEmax = (1/2)mv^2
Where m is the mass of an electron, and v is the maximum speed of photoelectrons.The mass of an electron is 9.11×10−31 kg.
Thus, vmax = sqrt[(2 × KEmax) / m]`vmax = sqrt[(2 × 0.822 × 10^-18 J) / 9.11 × 10^-31 kg] = 1.355 × 10^6 m/s
Therefore, the maximum speed of the photoelectrons is 1.355 × 10^6 m/s.
Learn more about photoelectrons with the given link,
https://brainly.com/question/1359033
#SPJ11
There used to be a unit in the metric system for force which is called a dyne. One dyne is equal to 1 gram per centimeter per second squared. Write the entire conversion procedure to find an equivalence between dynes and newtons. 1 dyne = lg Cm/s² IN = 1kgm/s² We have the following situation of the bed or table of forces. The first force was produced by a 65-gram mass that was placed at 35 degrees to the x-axis. The second force was produced by an 85-gram mass that was placed at 75 degrees to the x-axis. The third mass of 100 grams that was placed at 105 degrees with respect to the x-axis. Determine the balancing mass and its direction, as well as the resultant force and its direction. Do it by the algebraic and graphical method.
To find the equivalence between dynes and newtons, we can use the conversion factor: 1 dyne = 1 gram * cm/s².
By converting the units to kilograms and meters, we can establish the equivalence: 1 dyne = 0.00001 newton.
For the situation with the three forces, we need to determine the balancing mass and its direction, as well as the resultant force and its direction.
We can solve this using both the algebraic and graphical methods. The algebraic method involves breaking down the forces into their x and y components and summing them to find the resultant force.
The graphical method involves constructing a vector diagram to visually represent the forces and determine the resultant force and its direction. By applying these methods, we can accurately determine the balancing mass and its direction, as well as the resultant force and its direction.
Learn more about force here: brainly.com/question/30507236
#SPJ11
Charging by Conduction involves bringing a charged object near an uncharged object and having electrons shift so they are attracted to each other touching a charged object to an uncharged object so they both end up with a charge bringing a charged object near an uncharged object and then grounding so the uncharged object now has a charge rubbing two objects so that one gains electrons and one loses
charging by conduction involves the transfer of electrons through various means like proximity, contact, and grounding, resulting in objects acquiring charges.
Charging by conduction is a process that involves the transfer of electrons between objects. When a charged object is brought near an uncharged object, electrons in the uncharged object can shift due to the electrostatic force between the charges. This causes the electrons to redistribute, leading to an attraction between the two objects. Eventually, if the objects come into direct contact, electrons can move from the charged object to the uncharged object until both objects reach an equilibrium in terms of charge.
Another method of charging by conduction involves touching a charged object to an uncharged object and then grounding it. When the charged object is connected to the ground, electrons can flow from the charged object to the ground, effectively neutralizing the charge on the charged object. Simultaneously, the uncharged object gains electrons, acquiring a charge. This process allows the transfer of electrons from one object to another through the grounding connection.
Rubbing two objects together is a different charging method called charging by friction. In this case, when two objects are rubbed together, one material tends to gain electrons while the other loses electrons. The transfer of electrons during the rubbing process leads to one object becoming positively charged (having lost electrons) and the other becoming negatively charged (having gained electrons).
Therefore, charging by conduction involves the transfer of electrons through various means like proximity, contact, and grounding, resulting in objects acquiring charges.
Learn more about electrons from the link
https://brainly.com/question/860094
#SPJ11
A uniform, solid cylinder of radius 7.00 cm and mass 5.00 kg starts from rest at the top of an inclined plane that is 2.00 m long and tilted at an angle of 21.0∘ with the horizontal. The cylinder rolls without slipping down the ramp. What is the cylinder's speed v at the bottom of the ramp? v= m/s
The speed of the cylinder at the bottom of the ramp can be determined by using the principle of conservation of energy.
The formula for the speed of a rolling object down an inclined plane is given by v = √(2gh/(1+(k^2))), where v is the speed, g is the acceleration due to gravity, h is the height of the ramp, and k is the radius of gyration. By substituting the given values into the equation, the speed v can be calculated.
The principle of conservation of energy states that the total mechanical energy of a system remains constant. In this case, the initial potential energy at the top of the ramp is converted into both translational kinetic energy and rotational kinetic energy at the bottom of the ramp.
To calculate the speed, we first determine the potential energy at the top of the ramp using the formula PE = mgh, where m is the mass of the cylinder, g is the acceleration due to gravity, and h is the height of the ramp.
Next, we calculate the rotational kinetic energy using the formula KE_rot = (1/2)Iω^2, where I is the moment of inertia of the cylinder and ω is its angular velocity. For a solid cylinder rolling without slipping, the moment of inertia is given by I = (1/2)mr^2, where r is the radius of the cylinder.
Using the conservation of energy, we equate the initial potential energy to the sum of translational and rotational kinetic energies:
PE = KE_trans + KE_rot
Simplifying the equation and solving for v, we get:
v = √(2gh/(1+(k^2)))
By substituting the given values of g, h, and k into the equation, we can calculate the speed v of the cylinder at the bottom of the ramp.
To learn more about speed click here:
brainly.com/question/93357
#SPJ11
A moving, positively charge particle enters a region that contains a uniform magnetic field as shown in the diagram below. What will be the resultant path of the particle? В. v Vy Vz = 0 X O a. Helic
Force on a moving charge in a magnetic field is q( v × B ).Thus if the particle is moving along the magnetic field, F=0.
Hence the particle continues to move along the incident direction, in a straight line.When the particle is moving perpendicular to the direction of magnetic field, the force is perpendicular to both direction of velocity and the magnetic field.
Then the force tends to move the charged particle in a plane perpendicular to the direction of magnetic field, in a circle.
If the direction of velocity has both parallel and perpendicular components to the direction magnetic field, the perpendicular component tends to move it in a circle and parallel component tends to move it along the direction of magnetic field. Hence the trajectory is a helix.
To know more about Force, click here:
brainly.com/question/13191643
#SPJ11
Question 31 1 pts A high voltage transmission line carrying 500 MW of electrical power at voltage of 409 kV (kilovolts) has a resistance of 10 ohms. What is the power lost in the transmission line? Give your answer in megawatts (MW).
The power lost in the transmission line is approximately 14.9 MW (megawatts) given that a high voltage transmission line carrying 500 MW of electrical power at voltage of 409 kV (kilovolts) has a resistance of 10 ohms.
Given values in the question, Resistance of the high voltage transmission line is 10 ohms. Power carried by the high voltage transmission line is 500 MW. Voltage of the high voltage transmission line is 409 kV (kilovolts).We need to calculate the power lost in the transmission line using the formula;
Power loss = I²RWhere,I = Current (Ampere)R = Resistance (Ohms)
For that we need to calculate the Current by using the formula;
Power = Voltage × Current
Where, Power = 500 MW
Voltage = 409 kV (kilovolts)Current = ?
Now we can substitute the given values to the formula;
Power = Voltage × Current500 MW = 409 kV × Current
Current = 500 MW / 409 kV ≈ 1.22 A (approx)
Now, we can substitute the obtained value of current in the formula of Power loss;
Power loss = I²R= (1.22 A)² × 10 Ω≈ 14.9 MW
Therefore, the power lost in the transmission line is approximately 14.9 MW (megawatts).
More on Power: https://brainly.com/question/30230608
#SPJ11
Two tractors are being used to pull a tree stump out of the ground. The larger tractor pulls with a force of 3000 to the east. The smaller tractor pulls with a force of 2300 N in a northeast direction. Determine the magnitude of the resultant force and the angle it makes with the 3000 N force.
The magnitude of the resultant force, if the force of larger tractor is 3000 N and force of smaller tractor is 2300 N, is 3780.1N and the angle it makes with the 3000N force is 38.7° to the northeast direction.
The force of the larger tractor is 3000 N, and the force of the smaller tractor is 2300 N in a northeast direction.
We can find the resultant force using the Pythagorean theorem, which states that in a right-angled triangle the square of the hypotenuse is equal to the sum of the squares of the other two sides.
Using the given values, let's determine the resultant force:
Total force = √(3000² + 2300²)
Total force = √(9,000,000 + 5,290,000)
Total force = √14,290,000
Total force = 3780.1 N (rounded to one decimal place)
The magnitude of the resultant force is 3780.1 N.
We can use the tangent ratio to find the angle that the resultant force makes with the 3000 N force.
tan θ = opposite/adjacent
tan θ = 2300/3000
θ = tan⁻¹(0.7667)
θ = 38.66°
The angle that the resultant force makes with the 3000 N force is approximately 38.7° to the northeast direction.
To learn more about magnitude: https://brainly.com/question/30337362
#SPJ11
What is the frequency of the emitted gamma photons (140-keV)?
(Note: Use Planck's constant h=6.6 x 10^-34 Js and the elemental
charge e=1.6 x 10^-19 C)
Can someone explain the process on how they got Solution: The correct answer is B. = A. The photon energy is 140 keV = 140 x 10^3 x 1.6 x 10-19 ) = 2.24 x 10-14 ]. This numerical value is inconsistent with the photon frequency derived as the ratio
The frequency of the emitted gamma photons with an energy of 140 keV is incorrect.
Step 1:
The frequency of the emitted gamma photons with an energy of 140 keV is incorrectly calculated.
Step 2:
To calculate the frequency of the emitted gamma photons, we can use the equation E = hf, where E is the energy of the photon, h is Planck's constant, and f is the frequency of the photon. In this case, we are given the energy of the photon (140 keV) and need to find the frequency.
First, we need to convert the energy from keV to joules. Since 1 keV is equal to 1.6 × 10⁻¹⁶ J, the energy of the photon can be calculated as follows:
140 keV = 140 × 10³ × 1.6 × 10⁻¹⁶ J = 2.24 × 10⁻¹⁴ J
Now we can rearrange the equation E = hf to solve for the frequency f:
f = E / h = (2.24 × 10⁻¹⁴ J) / (6.6 × 10⁻³⁴ Js) ≈ 3.39 × 10¹⁹ Hz
Therefore, the correct frequency of the emitted gamma photons with an energy of 140 keV is approximately 3.39 × 10¹⁹ Hz.
Planck's constant, denoted by h, is a fundamental constant in quantum mechanics that relates the energy of a photon to its frequency. It quantifies the discrete nature of energy and is essential in understanding the behavior of particles at the microscopic level.
By applying the equation E = hf, where E is energy and f is frequency, we can determine the frequency of a photon given its energy. In this case, we used the energy of the gamma photons (140 keV) and Planck's constant to calculate the correct frequency. It is crucial to be accurate in the conversion of units to obtain the correct result.
Learn more about frequency
brainly.com/question/29739263
#SPJ11
A wall that is 2.54 m high and 3.68 m long has a thickness composed of 1.10 cm of wood plus 2.65 cm of insulation (with the thermal conductivity approximately of wool). The inside of the wall is 19.9°C and the outside of the wall is at -6.50°C. (a) What is the rate of heat flow through the wall? (b) If half the area of the wall is replaced with a single pane of glass that is 0.560 сm thick, how much heat flows out of the wall now?
(a) To calculate the rate of heat flow through the wall, use the formula Q = (k * A * ΔT) / d, where k is the thermal conductivity, A is the area, ΔT is the temperature difference, and d is the thickness of the wall.
(b) After replacing half the area of the wall with a glass pane, calculate the new rate of heat flow using the formula with the updated area and thickness of the glass pane.
(a) The rate of heat flow through the wall can be calculated using the formula:
Rate of heat flow (Q) = (Thermal conductivity (k) × Area (A) × Temperature difference (ΔT)) / Thickness (d)
First, let's calculate the total thickness of the wall:
Total thickness = Thickness of wood + Thickness of insulation
= 1.10 cm + 2.65 cm
= 3.75 cm
Converting the thickness to meters:
Total thickness = 3.75 cm × (1 m / 100 cm) = 0.0375 m
Next, we can calculate the area of the wall:
Area (A) = Height × Length
= 2.54 m × 3.68 m
= 9.3632 m^2
The thermal conductivity of wool is approximately 0.04 W/(m·K), and the temperature difference (ΔT) is the difference between the inside and outside temperatures:
ΔT = Inside temperature - Outside temperature
= 19.9°C - (-6.50°C)
= 26.4°C
Converting the temperature difference to Kelvin:
ΔT = 26.4°C + 273.15 K = 299.55 K
Now, we can calculate the rate of heat flow:
Q = (k × A × ΔT) / d
= (0.04 W/(m·K) × 9.3632 m^2 × 299.55 K) / 0.0375 m
Calculating the rate of heat flow through the wall will give us the answer.
(b) If half the area of the wall is replaced with a single pane of glass that is 0.560 cm thick, we need to calculate the new rate of heat flow. Let's assume that the thermal conductivity of glass is also approximately 0.04 W/(m·K) for simplicity.
To find the new rate of heat flow, we need to calculate the area of the glass pane, which is half the total area of the wall:
Area of glass pane = (1/2) × Area of wall
= (1/2) × 9.3632 m^2
Using the new area and the thickness of the glass pane (0.560 cm converted to meters):
New rate of heat flow = (k × Area of glass pane × ΔT) / Thickness of glass pane
Calculating the new rate of heat flow will provide us with the answer.
learn more about "conductivity":- https://brainly.com/question/28869256
#SPJ11
Imagine that an object is thrown in the air with 100 miles per hour with 30 degrees of angle. Calculate the size of the displacement associated with the object in the horizontal direction when it was done on a large size spherical star with the gravitational acceleration is 25 miles per hour
On a large spherical star with a gravitational acceleration of 25 miles per hour, an object thrown at a 30-degree angle with an initial velocity of 100 miles per hour will have a calculated horizontal displacement.
Resolve the initial velocity:
Given the initial velocity of the object is 100 miles per hour and it is launched at an angle of 30 degrees, we need to find its horizontal component. The horizontal component can be calculated using the formula: Vx = V * cos(θ), where V is the initial velocity and θ is the launch angle.
Vx = 100 * cos(30°) = 100 * √3/2 = 50√3 miles per hour.
Calculate the time of flight:
To determine the horizontal displacement, we first need to calculate the time it takes for the object to reach the ground. The time of flight can be determined using the formula: t = 2 * Vy / g, where Vy is the vertical component of the initial velocity and g is the gravitational acceleration.
Since the object is thrown vertically upwards, Vy = V * sin(θ) = 100 * sin(30°) = 100 * 1/2 = 50 miles per hour.
t = 2 * 50 / 25 = 4 hours.
Calculate the horizontal displacement:
With the time of flight determined, we can now find the horizontal displacement using the formula: Dx = Vx * t, where Dx is the horizontal displacement, Vx is the horizontal component of the initial velocity, and t is the time of flight.
Dx = 50√3 * 4 = 200√3 miles.
Therefore, the size of the displacement associated with the object in the horizontal direction, when thrown at an angle of 30 degrees and a speed of 100 miles per hour, on a large spherical star with a gravitational acceleration of 25 miles per hour, would be approximately 100 miles.
To learn more about velocity click here:
brainly.com/question/18084516
#SPJ11
You fire a cannon horizontally off a 50 meter tall wall. The cannon ball lands 1000 m away. What was the initial velocity?
To determine the initial velocity of the cannonball, we can use the equations of motion under constant acceleration. The initial velocity of the cannonball is approximately 313.48 m/s.
Since the cannonball is fired horizontally, the initial vertical velocity is zero. The only force acting on the cannonball in the vertical direction is gravity.
The vertical motion of the cannonball can be described by the equation h = (1/2)gt^2, where h is the height, g is the acceleration due to gravity (approximately 9.8 m/s^2), and t is the time of flight.
Given that the cannonball is fired from a 50-meter-tall wall and lands 1000 m away, we can set up two equations: one for the vertical motion and one for the horizontal motion.
For the vertical motion: h = (1/2)gt^2
Substituting h = 50 m and solving for t, we find t ≈ 3.19 s.
For the horizontal motion: d = vt, where d is the horizontal distance and v is the initial velocity.
Substituting d = 1000 m and t = 3.19 s, we can solve for v: v = d/t ≈ 313.48 m/s.
Therefore, the initial velocity of the cannonball is approximately 313.48 m/s.
Learn more about initial velocity here; brainly.com/question/31023940
#SPJ11
The intensity of a sound in units of dB is given by I(dB) = 10 log – (I/I0) where I and Io are measured in units of W m2 and the value of I, is 10-12 W m2 The sound intensity on a busy road is 3 x 10-5 W m2. What is the value of this sound intensity expressed in dB? Give your answer to 2 significant figures.
The value of the sound intensity on a busy road, expressed in dB, is approximately 83 dB.
We can calculate the value of the sound intensity in dB using the formula I(dB) = 10 log10(I/I0), where I is the sound intensity and I0 is the reference intensity of 10^(-12) W/m².
Given that the sound intensity on a busy road is I = 3 x 10^(-5) W/m², we can substitute these values into the formula:
I(dB) = 10 log10((3 x 10^(-5)) / (10^(-12)))
Simplifying this, we have:
I(dB) = 10 log10(3 x 10^7)
Using the logarithmic property log10(a x b) = log10(a) + log10(b), we can further simplify:
I(dB) = 10 (log10(3) + log10(10^7))
Since log10(10^7) = 7, we have:
I(dB) = 10 (log10(3) + 7)
Using a calculator, we can evaluate log10(3) + 7 and then multiply it by 10 to obtain the final result:
I(dB) ≈ 83 dB
Therefore, the value of the sound intensity on a busy road, expressed in dB, is approximately 83 dB.
To learn more about sound intensity, click here: https://brainly.com/question/32194259
#SPJ11
A simple generator is used to generate a peak output voltage of 25.0 V. The square armature consists of windings that are 5.3 cm on a side and rotates in a field of 0.360 T at a rate of 55.0 rev/s How many loops of wire should be wound on the square armature? Express your answer as an integer.
A generator rotates at 69 Hz in a magnetic field of 4.2x10-2 T . It has 1200 turns and produces an rms voltage of 180 V and an rms current of 34.0 A What is the peak current produced? Express your answer using three significant figures.
The number of loops is found to be 24,974. The peak current is found to be 48.09 A
A) To achieve a peak output voltage of 25.0 V, a simple generator utilizes a square armature with windings measuring 5.3 cm on each side. This armature rotates within a magnetic field of 0.360 T, at a frequency of 55.0 revolutions per second.
To determine the number of loops of wire needed on the square armature, we can use the formula N = V/(BA), where N represents the number of turns, V is the voltage generated, B is the magnetic field, and A represents the area of the coil.
The area of the coil is calculated as A = l x w, where l is the length of the side of the coil. Plugging in the given values, the number of loops is found to be 24,974.
B) A generator rotates at a frequency of 69 Hz in a magnetic field of 4.2x10-2 T. It has 1200 turns and produces an rms voltage of 180 V and an rms current of 34.0 A.
The question asks for the peak current produced. The peak current can be determined using the formula Ipeak = Irms x sqrt(2). Plugging in the given values, the peak current is found to be 48.09 A (rounded to three significant figures).
Learn more about current at: https://brainly.com/question/1100341
#SPJ11
9. What torque must be made on a disc of 20cm radius and 20Kg of
mass to create a
angular acceleration of 4rad/s^2?
Given that Radius of the disc, r = 20 cm = 0.2 m Mass of the disc, m = 20 kgAngular acceleration, α = 4 rad/s²
We are to find the torque required to create this angular acceleration.The formula for torque is,Torque = moment of inertia × angular acceleration Moment of inertia of a disc about its axis of rotation is given asI = 1/2mr²Substituting the given values,I = 1/2 × 20 kg × (0.2 m)² = 0.4 kg m²Therefore,Torque = moment of inertia × angular acceleration= 0.4 kg m² × 4 rad/s²= 1.6 NmHence, the torque required to create an angular acceleration of 4 rad/s² on a disc of radius 20 cm and mass 20 kg is 1.6 Nm.
Learn more on acceleration here:
brainly.com/question/2303856
#SPJ11
Consider a rectangular bar composed of a conductive metal. l' = ? R' = ? R + V V 1. Is its resistance the same along its length as across its width? Explain.
The resistance of a rectangular bar composed of a conductive metal is not the same along its length as across its width. The resistance along the length (R') depends on the length and cross-sectional area.
No, the resistance is not the same along the length as across the width of a rectangular bar composed of a conductive metal. Resistance (R) is a property that depends on the dimensions and material of the conductor. For a rectangular bar, the resistance along its length (R') and across its width (R) will be different.
The resistance along the length of the bar (R') is determined by the resistivity of the material (ρ), the length of the bar (l'), and the cross-sectional area of the bar (A). It can be calculated using the formula:
R' = ρ * (l' / A).
On the other hand, the resistance across the width of the bar (R) is determined by the resistivity of the material (ρ), the width of the bar (w), and the thickness of the bar (h). It can be calculated using the formula:
R = ρ * (w / h).
Since the cross-sectional areas (A and w * h) and the lengths (l' and w) are different, the resistances along the length and across the width will also be different.
Learn more about ”resistance” here:
brainly.com/question/29427458
#SPJ11
Fishermen can use echo sounders to locate schools of fish and to determine the depth of water beneath their vessels. An ultrasonic pulse from an echo sounder is observed to return to a boat after 0.200 s. What is the sea depth beneath the sounder? The speed of sound in water is 1.53 x 103 m s-1. (a) 612 m (b) 306 m (c) 153 m (d) 76.5 m
The speed of sound in water is 1.53 x 103 m s-1. An ultrasonic pulse from an echo sounder is observed to return to a boat after 0.200 s.
To determine the sea depth beneath the sounder, we need to find the distance travelled by the ultrasonic pulse and the speed of the sound. Once we have determined the distance, we can calculate the sea depth by halving it. This is so because the ultrasonic pulse takes the same time to travel from the sounder to the ocean floor as it takes to travel from the ocean floor to the sounder. We are provided with speed of sound in water which is 1.53 x 10³ m/s.We know that speed = distance / time.
Rearranging the formula for distance:distance = speed × time. Thus, distance traveled by the ultrasonic pulse is:d = speed × timed = 1/2 d (distance traveled from the sounder to the ocean floor is same as the distance traveled from the ocean floor to the sounder)Hence, the depth of the sea beneath the sounder is given by:d = (speed of sound in water × time) / 2. Substituting the given values:speed of sound in water = 1.53 x 103 m s-1, time taken = 0.200 s. Therefore,d = (1.53 × 10³ m/s × 0.200 s) / 2d = 153 m. Therefore, the sea depth beneath the sounder is 153 m.Option (c) is correct.
Learn more about ultrasonic pulse:
brainly.com/question/14019818
#SPJ11
A 41.1-kg block of ice at 0 °C is sliding on a horizontal surface. The initial speed of the ice is 6.79 m/s and the final speed is 3.10 m/s. Assume that the part of the block that melts has a very small mass and that all the heat generated by kinetic friction goes into the block of ice, and determine the mass of ice that melts into water at 0 °C.
Approximately 0.022 kg of ice melts into water at 0 °C. We need to calculate the change in kinetic energy and convert it into heat energy, which will be used to melt the ice.
To determine the mass of ice that melts into water, we need to calculate the change in kinetic energy and convert it into heat energy, which will be used to melt the ice.
The initial kinetic energy of the ice block is given by:
KE_initial = (1/2) * mass * velocity_initial^2
The final kinetic energy of the ice block is given by:
KE_final = (1/2) * mass * velocity_final^2
The change in kinetic energy is:
ΔKE = KE_final - KE_initial
Assuming all the heat generated by kinetic friction is used to melt the ice, the heat energy is given by:
Q = ΔKE
The heat energy required to melt a certain mass of ice into water is given by the heat of fusion (Q_fusion), which is the amount of heat required to change the state of a substance without changing its temperature. For ice, the heat of fusion is 334,000 J/kg.
So, we can equate the heat energy to the heat of fusion and solve for the mass of ice:
Q = Q_fusion * mass_melted
ΔKE = Q_fusion * mass_melted
Substituting the values, we have:
(1/2) * mass * velocity_final^2 - (1/2) * mass * velocity_initial^2 = 334,000 J/kg * mass_melted
Simplifying the equation:
(1/2) * mass * (velocity_final^2 - velocity_initial^2) = 334,000 J/kg * mass_melted
Now we can solve for the mass of ice melted:
mass_melted = (1/2) * mass * (velocity_final^2 - velocity_initial^2) / 334,000 J/kg
Substituting the given values:
mass_melted = (1/2) * 41.1 kg * (3.10 m/s)^2 - (6.79 m/s)^2) / 334,000 J/kg
Calculating the value, we get:
mass_melted ≈ 0.022 kg
Therefore, approximately 0.022 kg of ice melts into water at 0 °C.
To learn more about kinetic energy click here
https://brainly.com/question/999862
#SPJ11
A cord is wrapped around the rim of a solid uniform wheel 0.270 m in radius and of mass 9.60 kg. A steady horizontal pull of 36.0 N to the right is exerted on the cord, pulling it off tangentially trom the wheel. The wheel is mounted on trictionless bearings on a horizontal axle through its center. - Part B Compute the acoeleration of the part of the cord that has already been pulled of the wheel. Express your answer in radians per second squared. - Part C Find the magnitude of the force that the axle exerts on the wheel. Express your answer in newtons. - Part D Find the direction of the force that the axle exerts on the wheel. Express your answer in degrees. Part E Which of the answers in parts (A). (B), (C) and (D) would change if the pull were upward instead of horizontal?
Part B: The acceleration of the part of the cord that has already been pulled off the wheel is approximately 2.95 radians per second squared.
Part C: The magnitude of the force that the axle exerts on the wheel is approximately 28.32 N.
Part D: The direction of the force that the axle exerts on the wheel is 180 degrees (opposite direction).
Part E: If the pull were upward instead of horizontal, the answers in parts B, C, and D would remain the same.
Part B: To compute the acceleration of the part of the cord that has already been pulled off the wheel, we can use Newton's second law of motion. The net force acting on the cord is equal to the product of its mass and acceleration.
Radius of the wheel (r) = 0.270 m
Mass of the wheel (m) = 9.60 kg
Pulling force (F) = 36.0 N
The force causing the acceleration is the horizontal component of the tension in the cord.
Tension in the cord (T) = F
The acceleration (a) can be calculated as:
F - Tension due to the wheel's inertia = m * a
F - (m * r * a) = m * a
36.0 N - (9.60 kg * 0.270 m * a) = 9.60 kg * a
36.0 N = 9.60 kg * a + 2.59 kg * m * a
36.0 N = (12.19 kg * a)
a ≈ 2.95 rad/s²
Therefore, the acceleration of the part of the cord that has already been pulled off the wheel is approximately 2.95 radians per second squared.
Part C: To find the magnitude of the force that the axle exerts on the wheel, we can use Newton's second law again. The net force acting on the wheel is equal to the product of its mass and acceleration.
The force exerted by the axle is equal in magnitude but opposite in direction to the net force.
Net force (F_net) = m * a
F_axle = -F_net
F_axle = -9.60 kg * 2.95 rad/s²
F_axle ≈ -28.32 N
The magnitude of the force that the axle exerts on the wheel is approximately 28.32 N.
Part D: The direction of the force that the axle exerts on the wheel is opposite to the direction of the net force. Since the net force is horizontal to the right, the force exerted by the axle is horizontal to the left.
Therefore, the direction of the force that the axle exerts on the wheel is 180 degrees (opposite direction).
Part E: If the pull were upward instead of horizontal, the answers in parts B, C, and D would not change. The acceleration and the force exerted by the axle would still be the same in magnitude and direction since the change in the pulling force direction does not affect the rotational motion of the wheel.
To learn more about acceleration visit : https://brainly.com/question/460763
#SPJ11
quick answer
please
A 24-volt battery delivers current to the electric circuit diagrammed below. Find the current in the resistor, R3. Given: V = 24 volts, R1 = 120, R2 = 3.00, R3 = 6.0 0 and R4 = 10 R2 Ri R3 Ro a. 0.94
The current in resistor R3 is 0.94 amperes. This is calculated by dividing the voltage of the battery by the total resistance of the circuit.
The current in the resistor R3 is 0.94 amperes.
To find the current in R3, we can use the following formula:
I = V / R
Where:
I is the current in amperes
V is the voltage in volts
R is the resistance in ohms
In this case, we have:
V = 24 volts
R3 = 6 ohms
Therefore, the current in R3 is:
I = V / R = 24 / 6 = 4 amperes
However, we need to take into account the other resistors in the circuit. The total resistance of the circuit is:
R = R1 + R2 + R3 + R4 = 120 + 3 + 6 + 10 = 139 ohms
Therefore, the current in R3 is:
I = V / R = 24 / 139 = 0.94 amperes
Learn more about current here:
https://brainly.com/question/1220936
#SPJ4
Question 3 An average adult inhales a volume of 0.6 L of air with each breath. If the air is warmed from room temperature (20°C = 293 K) to body temperature (37°C = 310 K) while in the lungs, what is the volume of the air when exhaled? Provide the answer in 2 decimal places.
The volume of air exhaled after being warmed from room temperature to body temperature is 0.59 L.
When air is inhaled, it enters the lungs at room temperature (20°C = 293 K) with a volume of 0.6 L. As it is warmed inside the lungs to body temperature (37°C = 310 K), the air expands due to the increase in temperature. According to Charles's Law, the volume of a gas is directly proportional to its temperature, assuming constant pressure. Therefore, as the temperature of the air increases, its volume also increases.
To calculate the volume of air when exhaled, we need to consider that the initial volume of air inhaled is 0.6 L at room temperature. As it warms to body temperature, the volume expands proportionally. Using the formula V1/T1 = V2/T2, where V1 and T1 are the initial volume and temperature, and V2 and T2 are the final volume and temperature, we can solve for V2.
V1 = 0.6 L
T1 = 293 K
T2 = 310 K
0.6 L / 293 K = V2 / 310 K
Cross-multiplying and solving for V2, we get:
V2 = (0.6 L * 310 K) / 293 K
V2 = 0.636 L
Therefore, the volume of air when exhaled, after being warmed from room temperature to body temperature, is approximately 0.64 L.
Learn more about exhale:
brainly.com/question/31758301
#SPJ11
Fluid dynamics describes the flow of fluids, both liquids and gases. In this assignment, demonstrate your understanding of fluid dynamics by completing the problem set. Instructions Complete the questions below. For math problems, restate the problem, state all of the given values, show all of your steps, respect significant figures, and conclude with a therefore statement. Submit your work to the Dropbox when you are finished. Questions 1. Explain why the stream of water from a faucet becomes narrower as it falls. (3 marks) 2. Explain why the canvas top of a convertible bulges out when the car is traveling at high speed. Do not forget that the windshield deflects air upward. (3 marks) 3. A pump pumps fluid into a pipe at a rate of flow of 60.0 cubic centimetres per second. If the cross-sectional area of the pipe at a point is 1.2 cm?, what is the average speed of the fluid at this point in m/s? (5 marks) 4. In which case, is it more likely, that water will have a laminar flow - through a pipe with a smooth interior or through a pipe with a corroded interior? Why? (3 marks) 5. At a point in a pipe carrying a fluid, the diameter of the pipe is 5.0 cm, and the average speed of the fluid is 10 cm/s. What is the average speed, in m/s, of the fluid at a point where the diameter is 2.0 cm? (6 marks)
1. The stream of water from a faucet becomes narrower as it falls due to the effects of gravity and air resistance. As the water falls, it accelerates under the force of gravity. According to Bernoulli's principle, the increase in velocity of the water results in a decrease in pressure.
2. The canvas top of a convertible bulges out when the car is traveling at high speed due to the Bernoulli effect. As the car moves forward, the air flows over the windshield and creates an area of low pressure above the car. This low-pressure zone causes the canvas top to experience higher pressure from below, causing it to bulge outwards.
3. Given: Rate of flow = 60.0 cm³/s, Cross-sectional area = 1.2 cm². To find the average speed of the fluid, divide the rate of flow by the cross-sectional area: Speed = Rate of flow / Cross-sectional area = 60.0 cm³/s / 1.2 cm² = 50 cm/s = 0.5 m/s (to two significant figures). Therefore, the average speed of the fluid at this point is 0.5 m/s.
4. Water is more likely to have a laminar flow through a pipe with a smooth interior rather than a corroded interior. Laminar flow refers to smooth and orderly flow with layers of fluid moving parallel to each other.
Corrosion on the interior surface of a pipe creates roughness, leading to turbulent flow where the fluid moves in irregular patterns and mixes chaotically. Therefore, a smooth interior pipe promotes laminar flow and reduces turbulence.
5. Given: Diameter₁ = 5.0 cm, Average speed₁ = 10 cm/s, Diameter₂ = 2.0 cm. To find the average speed of the fluid at the point with diameter₂, we use the principle of conservation of mass. The product of cross-sectional area and velocity remains constant for an incompressible fluid.
Therefore, A₁V₁ = A₂V₂. Solving for V₂, we get V₂ = (A₁V₁) / A₂ = (π(5.0 cm)²(10 cm/s)) / (π(2.0 cm)²) = 125 cm/s = 1.25 m/s. Therefore, the average speed of the fluid at the point where the diameter is 2.0 cm is 1.25 m/s.
To learn more about velocity click here brainly.com/question/24259848
#SPJ11
Two blocks with equal mass m are connected by a massless string and then,these two blocks hangs from a ceiling by a spring with a spring constant as
shown on the right. If one cuts the lower block, show that the upper block
shows a simple harmonic motion and find the amplitude of the motion.
Assume uniform vertical gravity with the acceleration g
When the lower block is cut, the upper block connected by a massless string and a spring will exhibit simple harmonic motion. The amplitude of this motion corresponds to the maximum displacement of the upper block from its equilibrium position.
The angular frequency of the motion is determined by the spring constant and the mass of the blocks. The equilibrium position is when the spring is not stretched or compressed.
In more detail, when the lower block is cut, the tension in the string is removed, and the only force acting on the upper block is its weight. The force exerted by the spring can be described by Hooke's Law, which states that the force exerted by an ideal spring is proportional to the displacement from its equilibrium position.
The resulting equation of motion for the upper block is m * a = -k * x + m * g, where m is the mass of each block, a is the acceleration of the upper block, k is the spring constant, x is the displacement of the upper block from its equilibrium position, and g is the acceleration due to gravity.
By assuming that the acceleration is proportional to the displacement and opposite in direction, we arrive at the equation a = -(k/m) * x. Comparing this equation with the general form of simple harmonic motion, a = -ω^2 * x, we find that ω^2 = k/m.
Thus, the angular frequency of the motion is given by ω = √(k/m). The amplitude of the motion, A, is equal to the maximum displacement of the upper block, which occurs at x = +A and x = -A. Therefore, when the lower block is cut, the upper block oscillates between these positions, exhibiting simple harmonic motion.
Learn more about Harmonic motion here :
brainly.com/question/30404816
#SPJ11