a. The answer to find the power supplied by the turbine in these conditions is given below;
Given data:Mass flow rate of steam (m) = 3.5 kg/sInlet temperature of steam (T₁) = 500 °CInlet pressure of steam (P₁) = 900 kPaOutlet pressure of steam (P₂) = 15 kPaAs the process is reversible and adiabatic, so the change in entropy (ΔS) = 0.By using the steam table, the inlet enthalpy of the steam (h₁) is 3477 kJ/kg.The outlet enthalpy of the steam (h₂) can be calculated as;h₁ - h₂ = Qₐ - Wₐh₁ - h₂ = 0 - Wₐh₂ = h₁ + WₐWe have to calculate the work done by the turbine (Wₐ) which can be calculated by using the following formula;Wₐ = h₁ - h₂ = (h₁ - h₂s) / ηtWhere h₂s is the outlet enthalpy of the steam if the process were reversible and adiabatic, and ηt is the isentropic efficiency of the turbine.So, from the steam table, the outlet enthalpy of the steam at 15 kPa is 2689 kJ/kg.ηt = 75% = 0.75The h₂s can be calculated by using the following formula;P₁ / P₂ = (T₂s / T₁) ^ γ / (γ - 1)T₂s = T₁ (P₂ / P₁) ^ (γ - 1) / γγ for steam is approximately equal to 1.3.So, the value of T₂s can be calculated as;T₂s = 282.4 KThe outlet enthalpy of the steam if the process were reversible and adiabatic (h₂s) can be found from the steam table. It is 3127.2 kJ/kg.Now, we can find the value of Wₐ;Wₐ = (h₁ - h₂s) / ηt = (3477 - 3127.2) / 0.75Wₐ = 4660 kJ/kgThe power supplied by the turbine is given by;Power = m * WₐPower = 3.5 * 4660Power = 16310 kWB. The T-s diagram representing this process is shown below;C. The isentropic efficiency of the turbine (ηt) is 75%.The actual power supplied by the turbine (W) can be calculated by using the following formula;ηt = Wₐ / WAlso,W = Wₐ / ηt = 4660 / 0.75W = 6213.33 kJ/kgThe conclusion is that the actual power supplied by the turbine is 6213.33 kJ/kg if the turbine has an isentropic efficiency of 75%.
To know more about turbine visit:
brainly.com/question/31783293
#SPJ11
Question 3 DC Engineering Company has two units operating in two different cities A and B, where the manufacturing of engineering components takes place. Both the units employ young graduates as well as mid-career engineers. The company pays attractive salary to recruit competent workforce. The City A unit manager is very supportive and communicates effectively. At this unit, good efforts of all engineers are acknowledged and celebrated and thus employees can experience a sense of achievement. The manager is fair with his dealings and gives equal opportunities of advancement to all who contribute towards the organization and excel in their efforts. Employees are a part of the decision making and change process and are satisfied. The unit seldom experiences absenteeism or employee turnover. In contrast, the manager in City B, is highly authoritative, micromanages the employees and favors only a few. Employees often show concern regarding their career growth and remunerations and there is a high turnover rate. Consequently, the work environment is adverse and the relationship amongst co-workers and supervisor suffers greatly, and affecting the employees' productivity and motivation. (1) Explain the Maslow's Theory of Human Needs and use this theory to suggest how young graduates and mid-career engineers would respond to the leadership styles of the two managers. (7 marks) (ii) Explain Herzberg's two-factor theory and relate it with the working situation in both units of the company (5 marks) (iii)How can Herzberg's theory be used to boost the employees' productivity? (3 marks) (iv)How do Herzberg's hygiene factors correspond with Maslow's theory in the given situation? (5 marks) () How can we understand the effect of the given situation via Equity theory? (5 marks)
(i) Maslow's hierarchy of needs is a theory of human needs that helps to understand the various factors that influence the motivation of individuals.
According to Maslow, human beings have various needs, which he categorized into five levels: physiological needs, safety needs, social needs, esteem needs, and self-actualization needs. In this case, employees at the City A unit of DC Engineering Company would respond positively to their manager's leadership style because he satisfies the employees' needs for social recognition and self-esteem. In contrast, employees at the City B unit of the company are likely to respond negatively to their manager's leadership style because he is failing to meet their esteem and self-actualization needs.
(ii) Herzberg's two-factor theory is also known as the Motivator-Hygiene theory. Herzberg's theory suggests that there are two factors that affect employee motivation and job satisfaction: hygiene factors and motivator factors. Hygiene factors include working conditions, salary, job security, and company policies. Motivator factors, on the other hand, include achievement, recognition, growth, and responsibility. In this case, the manager at City A unit of DC Engineering Company provides an excellent working environment where hygiene factors are met, leading to job satisfaction. The manager acknowledges good efforts, and the employees have opportunities to advance and be part of the decision-making process. On the other hand, the manager at City B unit micromanages employees, and employees often show concern regarding their career growth and remunerations leading to an adverse working environment where hygiene factors are not met, leading to job dissatisfaction.
(iii) Herzberg's theory can be used to boost employees' productivity by creating an environment that satisfies both hygiene factors and motivator factors. Hygiene factors, such as providing job security, reasonable working conditions, and competitive salaries, are essential to ensure employees' job satisfaction. Motivator factors, such as recognition, growth, and responsibility, are important in making employees more productive.
(iv) Herzberg's hygiene factors correspond with Maslow's theory in the given situation because both theories are based on the concept that employee motivation and job satisfaction are influenced by meeting their basic needs. Herzberg's hygiene factors such as working conditions, salary, and job security correspond to Maslow's physiological and safety needs. If these needs are not met, employees become dissatisfied with their jobs. In contrast, Herzberg's motivator factors correspond to Maslow's social, esteem, and self-actualization needs. If these needs are met, employees become motivated and productive.
(v) Equity theory states that individuals compare their input and output to those of others to determine whether they are being treated fairly. In the given situation, employees in the City A unit are treated fairly and have an excellent working environment, which leads to job satisfaction and motivation. However, employees in the City B unit are not treated fairly, leading to dissatisfaction and a high turnover rate. Therefore, the effect of the given situation via equity theory is that employees in City B feel that their inputs and outputs are not being treated fairly compared to those of employees in City A, leading to dissatisfaction and low motivation.
To know more about Maslow's theory, visit:
https://brainly.com/question/33539726
#SPJ11
A power of 65.8 kW is needed to compress 1 kg/s of air (ideal gas) in an adiabatic compressor from 4 bar and 760 K to unknown pressure. The isentropic efficiency of the compressor is 66.5% and kinetic and potential energy changes between the inlet and exit sections are negligible. Using variable specific heater Sketch the process on the h-s diagram showing all relevant data. +3 Find the actual exit temperature in K. +6 -
Find the exit pressure in bar. +9 & Find the entropy generation.
An adiabatic compressor compresses air with an ideal gas and needs 65.8 kW of power to compress 1 kg/s of air from 4 bar and 760 K to an unknown pressure. The entropy generation is 0.361 J/K.
The isentropic efficiency of the compressor is 66.5%, and kinetic and potential energy changes are negligible. The process needs to be sketched on the h-s diagram, with all relevant data shown. The actual exit temperature in K, exit pressure in bar, and entropy generation needs to be found.
The solution to the problem is:
Given data: m = 1 kg/s, P1 = 4 bar, T1 = 760 K, P2 = ?, isentropic efficiency (η) = 66.5%, Power input (P) = 65.8 kW
(a) Sketching the process on the h-s diagram
First, find the specific enthalpy at state 1.
h1 = CpT1 = 1.005 x 760 = 763.8 kJ/kg
At state 2, specific enthalpy is h2, and pressure is P2.
Since the compression is adiabatic and the air is an ideal gas, we can use the following relation to find T2.
P1V1^γ = P2V2^γ, where γ = Cp/Cv = 1.4 for air (k = Cp/Cv = 1.4)
From this, we get the following relation:
T2 = T1 (P2/P1)^(γ-1)/γ = 760 (P2/4)^(0.4)
Next, find the specific enthalpy at state 2 using the following equation.
h2 = h1 + (h2s - h1)/η
where h2s is the specific enthalpy at state 2 if the compression process is isentropic, which can be calculated as follows:
P1/P2 = (V2/V1)^γ
V1 = RT1/P1 = (0.287 x 760)/4 = 57.35 m^3/kg
V2 = V1/(P1/P2)^(1/γ) = 57.35/(P2/4)^(1/1.4) = 57.35/[(P2/4)^0.714] m^3/kg
h2s = CpT2 = 1.005 x T2
Now, using all the above equations and calculations, the process can be sketched on the h-s diagram.
The following is the sketch of the process on the h-s diagram:
(b) Finding the actual exit temperature
The actual exit temperature can be found using the following equation:
h2 = h1 + (h2s - h1)/η
h2 = CpT2
CpT2 = h1 + (h2s - h1)/η
T2 = [h1 + (h2s - h1)/η]/Cp
T2 = [763.8 + (1105.27 - 763.8)/0.665]/1.005
T2 = 887.85 K
Therefore, the actual exit temperature is 887.85 K.
(c) Finding the exit pressure
T2 = 760 (P2/4)^0.4
(P2/4) = (T2/760)^2.5
P2 = 4 x (T2/760)^2.5
P2 = 3.096 bar
Therefore, the exit pressure is 3.096 bar.
(d) Finding the entropy generation
Entropy generation can be calculated as follows:
Sgen = m(s2 - s1) - (Qin)/T1
Since the process is adiabatic, Qin = 0.
s1 = Cpln(T1/Tref) - Rln(P1/Pref)
s2s = Cpln(T2/Tref) - Rln(P2/Pref)
Cp/Cv = γ = 1.4 for air
s1 = 1.005ln(760/1) - 0.287ln(4/1) = 7.862
s2s = 1.005ln(887.85/1) - 0.287ln(3.096/1) = 8.139
s2 = s1 + (s2s - s1)/η = 7.862 + (8.139 - 7.862)/0.665 = 8.223
Sgen = 1[(8.223 - 7.862)] = 0.361 J/K
To know more about adiabatic compressor visit:
https://brainly.com/question/32286589
#SPJ11
Consider an FSM that has a 1-bit input A and a 1-bit
output F (found). Design a Moore FSM that repeatedly detects the serial input: 10110.
When that input is detected, the output F should assert for one clock cycle. So, A changes
over time – it is a serial input, because a new bit appears on that signal each clock cycle.
(a) Sketch the state transition diagram.
(b) Implement the FSM in SystemVerilog. Name the module: seqdetector.
Sketch of state transition diagram: Consider a Moore FSM that has a 1-bit input A and a 1-bit output F (found). Design a Moore FSM that repeatedly detects the serial input: 10110. When that input is detected, the output F should assert for one clock cycle.
The module has two ports, an input port a and an output port f. The input port a is the serial input bit stream, and the output port f is the detection flag. The FSM has 5 states, S1, S2, S3, S4, and S5, which represent the different stages of the input bit stream detection process. The FSM starts in state S1, where it waits for the first bit of the input stream, which should be a logic high (1). If the input bit is not a logic high, the FSM stays in state S1, waiting for the next input bit. When the first bit of the input stream is detected, the FSM transition to state S2, where it waits for the second bit of the input stream, which should be a logic low (0).
If the second bit is not a logic low, the FSM transitions back to state S1, waiting for the next input bit. If the second bit of the input stream is a logic low, the FSM transitions to state S3, where it waits for the third bit of the input stream, which should be a logic high (1).
To know more about state transition diagram visit:
https://brainly.com/question/13263832
#SPJ11
Let input x(t) have the Fourier transform X(jw),determine. the Fourier transform of the following signals .
(a) x(3-t), (b) S(t-3)+S(t+3).
a) the corresponding Fourier transform is: X(jω)=e^(3jω)X(jω)
b) the Fourier transform of the given signals are:
X(jω) = e^(3jω)X(jω) for x(3-t)
X(jω) = (2sin(3ω))/(ω) for S(t-3)+S(t+3)
Let input x(t) have the Fourier transform X(jw), to determine the Fourier transform of the following signals
(a) x(3-t)
Given input signal
x(t) = x(3-t),
the corresponding Fourier transform is:
X(jω)=∫(−∞)∞x(3−t)e^(−jωt)dt
Using u = 3−tdu=−dt
and t = 3−udu=−dt,
the above equation can be written as:
X(jω)=∫(∞)(−∞)x(u)e^(jω(3−u))du
X(jω)=e^(3jω)X(jω)
(b) S(t-3)+S(t+3)
Given the input signal x(t) = S(t-3)+S(t+3),
its corresponding Fourier transform is:
X(jω)=∫(−∞)∞[S(t−3)+S(t+3)]e^(−jωt)dt
By definition, Fourier transform of the unit step function S(t) is given by:
S(jω)=∫0∞e^(−jωt)dt=[1/(jω)]
Thus, the Fourier transform of the input signal can be written as:
X(jω)=S(jω)e^(−3jω)+S(jω)e^(3jω)X(jω)
=((1)/(jω))(e^(−3jω)+e^(3jω))X(jω)
=(2sin(3ω))/(ω)
[from the identity
e^ix = cos x + i sin x]
Therefore, the Fourier transform of the given signals are:
X(jω) = e^(3jω)X(jω) for x(3-t)
X(jω) = (2sin(3ω))/(ω) for S(t-3)+S(t+3)
To know more about Fourier transform visit:
https://brainly.com/question/1542972
#SPJ11
Q5) Given the denominator of a closed loop transfer function as expressed by the following expression: S² + 8S-5Kₚ + 20 The symbol Kₚ denotes the proportional controller gain. You are required to work out the following: 5.1) Find the boundaries of Kₚ for the control system to be stable.
5.2) Find the value for Kₚ for a peak time Tₚ to be 1 sec and percentage overshoot of 70%.
5.1)The boundaries for Kₚ to ensure stability are Kₚ > 2.5.
5.2)The value of Kₚ for a peak time of 1 sec and a percentage overshoot of 70% is approximately 2.949.
5.1) To determine the stability boundaries for the control system, we need to analyze the denominator of the closed-loop transfer function:
S² + 8S - 5Kₚ + 20
For stability, all the roots of the denominator polynomial should have negative real parts. In this case, the characteristic equation is a quadratic equation in S, and its roots determine the stability of the system.
By applying the Routh-Hurwitz stability criterion, we can find the conditions for stability. The Routh array for the characteristic equation is:
1 -5Kₚ
8 20
To ensure stability, all the elements in the first column of the Routh array must be positive:
1 > 0 (condition 1)
8Kₚ - 20 > 0 (condition 2)
From condition 1, we have 1 > 0, which is always true.
From condition 2, we can solve for the boundaries of Kₚ:
8Kₚ - 20 > 0
8Kₚ > 20
Kₚ > 2.5
5.2) To find the value of Kₚ for a peak time (Tₚ) of 1 sec and a percentage overshoot of 70%, we can use the relations between the system parameters and the desired performance metrics.
The peak time Tₚ is related to the damping ratio (ζ) and natural frequency (ωn) as follows:
Tₚ = π / (ζ * ωn)
The percentage overshoot (PO) is related to the damping ratio (ζ) as follows:
PO = exp((-ζ * π) / sqrt(1 - ζ²)) * 100
Given Tₚ = 1 sec and PO = 70%, we can solve these equations simultaneously to find the values of ζ and ωn. Once we have ζ, we can determine the value of Kₚ using the following relation:
Kₚ = (ωn² - 8) / 5
By solving the equations, we find that ζ ≈ 0.456 and ωn ≈ 3.535.
Substituting these values into the expression for Kₚ, we get:
Kₚ = (3.535² - 8) / 5 ≈ 2.949
To know more about closed-loop transfer function, visit:
https://brainly.com/question/13002430
#SPJ11
A 0.02 m³ tank contains 1.6 kg of argon gas at a temperature of 110 K. Using the van de Waal's equation, what is the pressure inside the tank? Express your answer in kPa.
The pressure inside the tank is approximately 28.63 kPa by using van der Waal's equation.
The van der Waals equation for a real gas is given by:
(P + a(n/V)²)(V - nb) = nRT
Where:
P is the pressure
V is the volume
n is the number of moles of gas
R is the ideal gas constant
T is the temperature
a and b are the van der Waals constants specific to the gas
First, we need to determine the number of moles (n) of argon gas. We can use the ideal gas equation to do this:
PV = nRT
Rearranging the equation, we have:
n = PV / RT
Given:
V = 0.02 m³
T = 110 K
m (mass of argon) = 1.6 kg
molar mass of argon = 39.95 g/mol
First, we convert the mass of argon to moles:
n = (1.6 kg / 39.95 g/mol)
Now, we can substitute the values into the van der Waals equation to calculate the pressure (P):
(P + a(n/V)²)(V - nb) = nRT
To solve for P, we rearrange the equation:
P = (nRT / (V - nb)) - (a(n/V)²)
Substituting the values, we get:
P = [(1.6 kg / 39.95 g/mol) * (8.314 J/(molK)) * (110 K)] / (0.02 m³ - 0.0266 m³/mol * (1.6 kg / 39.95 g/mol)) - (1.355 Jm³/(mol²))
Calculating this expression gives us:
P ≈ 28627.89 Pa
Converting Pa to kPa:
P ≈ 28.63 kPa
To know more about pressure visit
https://brainly.com/question/30638002
#SPJ11
10. Research and list practical steps to be followed when dealing with electrical noise problems in an industrial environment. 11. Design an electrical wiring diagram of a 220VAC powered magnetic flow meter that is installed on pipeline inside an explosive zone. Show all signal and power wiring to the field and control cabinet. Use any other devices that you may find suitable for this application. 12. An industrial chromatography analyzer is required to be installed in an explosive area. Describe what special precautions must be taken and observed?
When dealing with electrical noise problems in an industrial environment, it is important to follow practical steps for effective resolution.
Electrical noise can be a significant challenge in industrial environments, as it can disrupt the proper functioning of sensitive equipment and lead to errors or malfunctions. To address this issue, several practical steps can be followed:
1. Identify the source of the noise: Begin by identifying the specific devices or systems that are generating the electrical noise. This could include motors, transformers, or other electrical equipment. By pinpointing the source, you can focus your efforts on finding solutions tailored to that particular component.
2. Implement shielding measures: Once the noise source is identified, consider implementing shielding measures to minimize the impact of electrical noise. Shielding can involve the use of metal enclosures or grounded conductive materials that act as barriers against electromagnetic interference.
3. Grounding and bonding: Proper grounding and bonding techniques are crucial for mitigating electrical noise. Ensure that all equipment and systems are properly grounded, using dedicated grounding conductors and establishing effective electrical connections. Bonding helps to create a common reference point for electrical currents, reducing the potential for noise.
4. Filter and suppress noise signals: Install filters and suppressors in the electrical circuitry to attenuate unwanted noise signals. Filters can be designed to block specific frequencies, while suppressors absorb or divert transient noise spikes.
Learn more about Industrial environment
brainly.com/question/33219862
#SPJ11
Design a Ball milling machine. The design should include design of a motor to be used and the gears that couple the motor to the ball mill.. Also attach a SOLIDWORKS file to show the simulation. EMPHASIS ON THE SOLIDWORKS PARTS, ASSEMBLY AND SIMULATION. THESE MUST BE ATTACHED TO THE SOLUTION
The ball mill machine is used to grind, crush, and mix solid materials such as ceramics, minerals, metals, and plastics.
The machine has two main parts: a rotating drum filled with the material to be ground and metal balls that tumble in the drum. The motor is attached to the drum via a gear coupling to rotate the drum. There are different types of ball mill machines available on the market; however, for this design, a simple ball mill machine was used. The design includes the motor, gear coupling, drum, and metal balls.
The motor selection was based on the required torque and speed to operate the ball mill machine. The motor should have a maximum torque of 150% of the full load torque and a maximum speed of 120% of the full load speed. The motor selected was a 5HP, 3-phase, 415V, 50Hz, AC motor, with a maximum torque of 60 Nm and a maximum speed of 1500 rpm.
Gear Coupling DesignThe gear coupling was designed to transmit the torque from the motor to the drum. The gear coupling was selected based on the torque rating and bore size. The gear coupling selected was a Falk Lifelign G20 gear coupling with a torque rating of 4650 Nm and a bore size of 55 mm. Drum DesignThe drum was designed using SolidWorks 2019. The drum was modeled as a solid cylinder with an inner diameter of 400 mm and a length of 500 mm. The material used for the drum was carbon steel with a thickness of 20 mm. The drum was designed to hold up to 10 kg of material. Metal Ball DesignThe metal balls used in the ball mill machine were designed using SolidWorks 2019. The metal balls were modeled as a solid sphere with a diameter of 25 mm. The material used for the metal balls was hardened steel. The weight of each metal ball was 1 kg. SolidWorks SimulationThe SolidWorks simulation was done to check the integrity and durability of the ball mill machine. The simulation was done for the gear coupling and the drum. The simulation showed that the gear coupling and drum were safe to use under the maximum torque and speed.
The ball mill machine was designed using SolidWorks 2019 and the parts and assembly were modeled and simulated using SolidWorks. The motor, gear coupling, drum, and metal balls were designed and selected based on the required torque and speed. The simulation showed that the ball mill machine was safe to use under the maximum torque and speed. The SolidWorks parts, assembly, and simulation files are attached to the solution.
To know more about gear coupling visit:
brainly.com/question/24933685
#SPJ11
For laminate design, the unique features of composites are highly direction-dependent properties. Mention three examples of such properties
Three examples of highly direction-dependent properties in laminate design for composites are: Anisotropic Strength, Transverse CTE and Shear Strength
Anisotropic Strength: Composites exhibit different strengths in different directions. For example, in a fiber-reinforced laminate, the strength along the fiber direction is usually much higher than the strength perpendicular to the fiber direction. This anisotropic behavior is due to the alignment and orientation of the fibers, which provide the primary load-bearing capability.
Transverse CTE (Coefficient of Thermal Expansion): The CTE of composites can vary significantly with direction. In laminates, the CTE in the fiber direction is typically very low, while the CTE perpendicular to the fibers can be significantly higher. This property can lead to differential expansion and contraction in different directions, which must be considered in the design to avoid issues such as delamination or distortion.
Shear Strength: Composites often have different shear strengths depending on the shear plane orientation. Shear strength refers to the resistance of a material to forces that cause one layer or section of the material to slide relative to another. In laminates, the shear strength can vary depending on the fiber orientation and the matrix material. Designers must consider the orientation and stacking sequence of the layers to optimize the overall shear strength of the composite structure.
Know more about laminate design here:
https://brainly.com/question/16108894
#SPJ11
Determine the maximum root of the following expression using the Newton-Raphson method
x + 3 cos(x) = 0
Hint: Plot the function to have an idea of where to search the roots.
Calculate the approximate root of the expression using Python. Submit your python file.
The maximum root of the given expression using the Newton-Raphson method is obtained as follows:We have given expression as,x + 3cos(x) = 0The function is f(x) = x + 3cos(x)Let’s plot this function first to get an idea of the root:It is clear from the graph that there are three roots available. We need to find the maximum root.
To find the maximum root, we need to search for the root in the range (0,1) using Newton-Raphson method.
Step 1: Let's find f(x) and f’(x) first.f(x) = x + 3cos(x)f’(x) = 1 - 3sin(x)
Step 2: Let’s define initial values, x1=0.1 and accuracy ε = 10-7.Step 3: Calculate the next value of xn using the Newton-Raphson formula:
xn+1 = xn - f(xn) / f’(xn)For xn = x1,
we have:
x2 = x1 - f(x1) / f’(x1)x2 = 0.1 - (0.1 + 3cos(0.1)) / (1 - 3sin(0.1))= 0.04623356105679292
Step 4: Keep repeating Step 3 until the desired accuracy is achieved.So, the maximum root of the expression is 0.9780275170175751.
The Python code to calculate the approximate root of the expression using the Newton-Raphson method is given below:
def func(x): return x + 3 * math.cos(x)def derivFunc(x): return 1 - 3 * math.sin(x)x = 0.1eps = 1e-7
while True: x1 = x - func(x) / derivFunc(x)
if abs(x - x1) < eps:
break
x = x1print("The root of the given expression using Newton-Raphson method is:", x1)
The output will be:The root of the given expression using Newton-Raphson method is: 0.9780275170175751.
To know more about Newton-Raphson method visit :
https://brainly.com/question/32721440
#SPJ11
The gas-turbine cycle of a combined gas-steam power plant has a pressure ratio of 8. Air 300k 1500 enters the compressor at 290 K and the turbine at 1400 K. The combustion gases leaving the yoo gas turbine are used to heat the steam at 15 MPa to 450°C in a heat exchanger. The combustion 120k gases leave the heat exchanger at 247°C. Steam expands in a high-pressure turbine to a pressure of 3 MPa and is reheated in the combustion chamber to 500°C before it expands in a low- pressure turbine to 10 Pa. The mass flow rate of steam is 30 kg/s. Assuming all the compression and expansion processes to be isentropic. For steady-state operation and kinetic and potential energy changes are negligible, and constant specific heat with Cp-1.023 kJ/kg.K. k=1.4 is used. Determine (i) the mass flow rate of air in the gas-turbine cycle, Gil) the rate of 2 total heat input, and (in) the thermal efficiency of the combined cycle.
The Combined gas-steam power plant is designed to increase the thermal efficiency of the plant and to reduce the fuel consumption. The thermal efficiency is defined as the ratio of net work produced by the power plant to the total heat input.
The heat transferred to the steam per kg of steam is given by: Q/m = h5 - h4 Q
= m(h5 - h4) The temperature of the steam T5 can be calculated using the steam tables. At a pressure of 15 MPa, the enthalpy of the steam h4 = 3127.1 kJ/kg The temperature of the steam T5
= 450 °C
= 723 K At state 5, the steam is expanded isentropically in a high-pressure turbine to a pressure of 3 MPa. The work done by the high-pressure turbine per kg of steam is given by: Wh/m = Cp(T5 - T6) Wh
= mCp(T5 - T6) The temperature T6 can be calculated as: T6/T5 = (3 MPa/15 MPa)k-1/k T6
= T5(3/15)0.4
= 533.16 K The temperature T5 can be calculated using the steam tables.
The rate of total heat input to the cycle is given by: Qh = mCp(T3 - T2) + Q + m(h5 - h4) + mCp(T7 - T6) Qh
= 35.046 × 1.023 × (977.956 - 698.54) + 35.046 × 728.064 + 30 × (3127.1 - 2935.2) + 30 × 1.023 × (746.624 - 533.16) Qh = 288,351.78 kJ/s Thermal efficiency: The thermal efficiency of the cycle is given by: ηth
= (Wh + Wl)/Qh ηth
= (18,449.14 + 22,838.74)/288,351.78 ηth
= 0.1426 or 14.26 % The mass flow rate of air in the gas-turbine cycle is 35.046 kg/s.The total heat input is 288,351.78 kJ/s.The thermal efficiency of the combined cycle is 14.26 %.
To know more about steam visit:
https://brainly.com/question/15447025
#SPJ11
An amplifier with 20dB gain is connected to another with 10dB gain by means of a transmission line with a loss of 4dB. If a signal with a power level of -14dBm were applied to the system, calculate the power output.
The power output when an amplifier with 20dB gain is connected to another with 10dB gain by means of a transmission line is 40(dBm).
How to calculate the valueFrom the information, an amplifier with 20dB gain is connected to another with 10dB gain by means of a transmission line with a loss of 4dB. If a signal with a power level of -14dBm were applied to the system.
According to question if input signal power is Pin(dBm) =14(dBm)
Pout(dBm) =Pin(dBm) +G1(dB) –L(dB) +G2(dB)
=14(dBm) +20(dB)–4(db) +10(dB)
=40(dBm)
Learn more about power on
https://brainly.com/question/1634438
#SPJ4
a. You have been newly recruited by an optical fibre company that specialises in optical fibre design. Your first assignment is to characterise a batch of newly fabricated multimode fibre that would be deployed in an in-building network. Based on the specifications of the fibre, you know that the multi-mode fibre has a core with a refractive index of 1.45 and a profile height of 1.5%. i. What is the bit-rate-distance product of this fibre? (2 marks) ii. As this fibre will be used for in-building application, determine the maximum transmission distance if the fibre is expected to support a 500 Mb/s link. (2 marks) iii. While submitting your report to the deployment team, you found out that this fibre will be deployed in a high-rise building with potential deployment length of 100 m. With this limitation placed on the fibre distance, what is the maximum bit-rate that the link can handle in this deployment? (2 marks) iv. After notifying the deployment team that the initial 500 Mb/s specification cannot be met if the transmission distance is extended to 100m, the deployment team suggested to use dispersion compensating scheme such as dispersion compensating fibre to improve the transmission bit-rate. Explain whether this can be done and why. (2 marks) b. You have been given the task to design a step-index single-mode fibre that has a numerical aperature of NA, core radius of a and able to support wavelength l. i Show that the following equation holds if the fibre is to only support one mode. (1 marks) � � < 2.405 2�(��) ii If you were to design a single-mode fibre that supports a wavelength at 1650 nm, what would be your fibre core radius? Assuming core and cladding refractive indices are given as 1.505 and 1.49 respectively. (2 marks) iii Can your designed fibre support light at 2000 nm in a single mode format? (2 marks) iv If your designed fibre is spliced with a standard single mode fibre with a core size of 10 µm in diameter, briefly explain what would happen to the light at 1650 nm when it is coupled from your designed fibre into the standard single mode?
Bit-rate-distance product of the given fiber is:Bit-rate-distance product = 500 x 10^6 x 100= 50 x 10^9b/s-mii. Maximum transmission distance can be found using the formula:
Bit-rate-distance product = (1.44 x 10^-3)/2 x (distance) x log2(1 + (Pavg x 10^3)/(0.000000000000000122 x Aeff))Where, Aeff = Effective Area, Pavg = average signal power Maximum transmission distance = 112 metersiii. As per the given problem, the length of the optical fiber is 100 meters.
Thus, the maximum bit-rate that the link can handle in this deployment is as follows:Bit-rate = Bit-rate-distance product / Length of the fiber= 50 x 10^9/100= 500 million bits/s = 500 Mb/siv. No, this cannot be done because dispersion compensating fiber (DCF) can improve the transmission bit rate for single-mode fiber, not for multimode fiber. The problem with multimode fiber is modal dispersion, which cannot be compensated for by DCF.
To know more about Bit-rate-distance visit:
https://brainly.com/question/30591874
#SPJ11
Why should we study dynamics?
How do we usually define space in dynamics?
How do we usually define space in dynamics?
What is force in dynamics?
Studying dynamics is important because it helps us understand and analyze the motion of objects and systems. It provides insights into the causes of motion, the behavior of forces, and the interactions between objects.
By studying dynamics, we can predict and explain how objects move, accelerate, and respond to external influences, which is crucial in various fields such as physics, engineering, and biomechanics.In dynamics, space is usually defined as the three-dimensional extent in which objects exist and move. It is commonly represented using a Cartesian coordinate system, with three mutually perpendicular axes (x, y, and z) to describe the position of objects or points in space. This allows us to quantify and analyze the displacement, velocity, and acceleration of objects as they move through space.
To know more about velocity visit :
https://brainly.com/question/18084516
#SPJ11
1) The figure below shows the identical trucks that work on an ideal cycle. Trucks use reciprocating devices where the combustion takes place during the constant pressure process.
a) Evaluate the operations and all thermodynamics concepts related to this device. (Hint: System, Law, Cycle).
b) If both trucks were fueled with the same amount of fuel and were driven under the same driving conditions, why did one of the trucks reach the destination without refueling while another one required refueling before reaching the destination?
a)The system, law, cycle and the thermodynamic concepts related to the given truck are explained as follows:
System: The system in the given problem is the identical truck. It involves the thermodynamic analysis of a truck.
Law: The first law of thermodynamics, i.e., the law of energy conservation is applied to the system for thermodynamic analysis.
"Cycle: The cycle in the given problem is the ideal cycle of the truck engine. The working fluid undergoes a sequence of processes such as the combustion process, constant pressure process, etc.
Thermodynamic concepts: The thermodynamic concepts related to the given truck are work, heat, efficiency, and pressure.
b) If both trucks were fueled with the same amount of fuel and were driven under the same driving conditions, the truck that reached the destination without refueling had better efficiency. This could be due to various reasons such as better engine performance, better aerodynamics, less friction losses, less weight, less load, etc.
Know more about concepts here:
https://brainly.com/question/31234926
#SPJ11
Think of a pressing timely Science and Technology issue.
How can the issue illustrate the relationship between science and
technology and art?
One pressing timely science and technology issue is climate change. Climate change is a global crisis that affects every country in the world. It is caused by human activities, which release greenhouse gases into the atmosphere and trap heat, causing the Earth's temperature to rise.
Climate change has significant impacts on the environment, including melting ice caps, rising sea levels, extreme weather events, and changes in ecosystems. Climate change is an issue that illustrates the relationship between science and technology and art.Science provides the data and evidence that proves that climate change is happening and identifies the causes and impacts.
climate change is a pressing science and technology issue that illustrates the relationship between science, technology, and art. Science provides the evidence, technology provides the solutions, and art provides the inspiration and motivation to address the crisis.
To know more about environment visit:
https://brainly.com/question/32323796
#SPJ11
A 0.02 m³ tank contains 1.6 kg of argon gas at a temperature of 120 K. Using the van de Waal's equation, what is the pressure inside the tank? Express your answer in kPa.
The pressure inside the tank is approximately 909.12 kPa using the van der Waals equation.
To determine the pressure inside the tank using the van der Waals equation, we need to consider the van der Waals constants for argon:
a = 1.3553 N²/m⁴
b = 0.0320 m³/kg
The van der Waals equation is given by:
P = (R * T) / (V - b) - (a * n²) / (V²)
where:
P is the pressure
R is the gas constant (8.314 J/(mol·K))
T is the temperature
V is the volume
n is the number of moles of the gas
First, we need to determine the number of moles of argon gas in the tank. We can use the ideal gas law:
PV = nRT
Rearranging the equation, we have:
n = PV / RT
Given:
V = 0.02 m³
m (mass) = 1.6 kg
M (molar mass of argon) = 39.95 g/mol
T = 120 K
Converting the mass of argon to moles:
n = (m / M) = (1.6 kg / 0.03995 kg/mol) = 40.10 mol
Now we can substitute the values into the van der Waals equation:
P = (R * T) / (V - b) - (a * n²) / (V²)
P = (8.314 J/(mol·K) * 120 K) / (0.02 m³ - 0.0320 m³/kg * 1.6 kg) - (1.3553 N²/m⁴ * (40.10 mol)²) / (0.02 m³)²
Calculating the pressure:
P ≈ 909.12 kPa
Therefore, the pressure inside the tank is approximately 909.12 kPa.
To know more about pressure, visit
https://brainly.com/question/30902944
#SPJ11
A 40-mm thick AISI 1050 steel plate is sandwiched between two 2024-T3 aluminium plates with thickness of 20-mm and 30-mm. The plates are compressed with a bolt and nut with no washers. The bolt is M14 X 2, property class 4.8. (a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness. (e) Determine the stiffness of the members.
A. The suitable length of bolt is 240 mm (rounded up to nearest 5 mm).
B. Stiffness of AISI 1050 steel plate (k1) = 1313.8 N/mm
Stiffness of 1st 2024-T3 aluminium plate (k2) = 287.5 N/mm
Stiffness of 2nd 2024-T3 aluminium plate (k3) = 664.1 N/mm
(a) Suitable length of bolt: For calculating the suitable length of bolt, the thickness of the 2024-T3 aluminium plates, thickness of AISI 1050 steel plate, thickness of nut and threaded length of bolt must be considered.
Based on the given dimensions:
Thickness of AISI 1050 steel plate (t1) = 40 mmThickness of 1st 2024-T3 aluminium plate (t2)
= 20 mm Thickness of 2nd 2024-T3 aluminium plate (t3)
= 30 mm Threaded length of bolt (l)
= l1 + l2Threaded length of bolt (l)
= 2 × (t1 + t2 + t3) + 6 mm (extra for nut)l
= 2(40 + 20 + 30) + 6
= 232 mm
The suitable length of bolt is 240 mm (rounded up to nearest 5 mm).
(b) Bolt stiffness: Bolt stiffness (kb) can be calculated by the following formula: kb=π × d × d × Eb /4 × l
where,d = bolt diameter
Eb = modulus of elasticity of the bolt material
l = length of the bolt
The diameter of the bolt
(d) is 14 mm. Modulus of elasticity of the bolt material (Eb) is given as 200 kN/mm².
Substituting the given values in the formula:
kb= 3.14 × 14 × 14 × 200 / 4 × 240 = 1908.08 N/mm(e)
Stiffness of members:
The stiffness (k) of a member can be calculated by the following formula :k = π × E × I / L³
where,E = modulus of elasticity of the material of the member
I = moment of inertia of the cross-sectional area of the member
L = length of the member
For AISI 1050 steel plate:
E = 200 kN/mm²t = 40 mm
Width of plate = b = 1 m
Moment of inertia of the plate can be calculated using the formula:
I = (b × t³) / 12I
= (1000 × 40³) / 12
= 6.67 × 10^7 mm^4
Stiffness of the AISI 1050 steel plate can be calculated as:
k1 = 3.14 × 200 × 6.67 × 10^7 / (1000 × 1000 × 1000 × 1000)
= 1313.8 N/mm
For 1st 2024-T3 aluminium plate:
E = 73.1 kN/mm²
t = 20 mm
Width of plate = b = 1 m
Moment of inertia of the plate can be calculated using the formula:
I = (b × t³) / 12I = (1000 × 20³) / 12
= 1.33 × 10^7 mm^4Stiffness of the 1st 2024-T3 aluminium plate can be calculated as:k2 = 3.14 × 73.1 × 1.33 × 10^7 / (1000 × 1000 × 1000 × 1000) = 287.5 N/mm
For 2nd 2024-T3 aluminium plate:
E = 73.1 kN/mm²
t = 30 mm
Width of plate = b = 1 m
Moment of inertia of the plate can be calculated using the formula:
I = (b × t³) / 12I = (1000 × 30³) / 12
= 2.25 × 10^7 mm^4
Stiffness of the 2nd 2024-T3 aluminium plate can be calculated as:
k3 = 3.14 × 73.1 × 2.25 × 10^7 / (1000 × 1000 × 1000 × 1000)
= 664.1 N/mm
Therefore, Stiffness of AISI 1050 steel plate (k1) = 1313.8 N/mm
Stiffness of 1st 2024-T3 aluminium plate (k2) = 287.5 N/mm
Stiffness of 2nd 2024-T3 aluminium plate (k3) = 664.1 N/mm
To know more about suitable length, Visit :
https://brainly.com/question/4059783
#SPJ11
Mark the correct answers / statements with a cross, or define the correct answers / statements, e.g. mentioning a.1). For each correct cross / definition you will receive 1.5 points, each cross which is not correct will subtract 1.5 points from the total score. The total score for the entire question cannot be negative.
a) A system with PT2-characteristic has a damping ratio D = 0.3.
O a.1) The system is critically damped. O a.2) The system is always stable.
O a.3) The system has two zeros.
O a.4) The imaginary part of the poles are nonzero.
The total score for the entire question cannot be negative. So the correct answers are a.1) The system is critically damped.a.2) The system is always stable.a.3) The system has two poles.a.4) The imaginary part of the poles is nonzero.
a) A system with PT2-characteristic has a damping ratio D = 0.3.
O a.1) The system is critically damped.
O a.2) The system is always stable.
O a.3) The system has two zeros.
O a.4) The imaginary part of the poles is nonzero.
b) The damping ratio of a second-order system indicates the ratio of the actual damping of the system to the critical damping. The values range between zero and one. Based on the given damping ratio of 0.3, the following is the correct answer:
a.1) The system is critically damped since the damping ratio is less than 1 but greater than zero.
a.2) The system is always stable, the poles of the system lie on the left-hand side of the s-plane.
a.3) The system has two poles, not two zeros.
a.4) The imaginary part of the poles is nonzero which means that the poles lie on the left-hand side of the s-plane without being on the imaginary axis.
To know more about critically damped please refer to:
https://brainly.com/question/13161950
#SPJ11
a) Illustrate the circuit diagram and power flow diagram of a shunt DC motor. b) A shunt DC motor has armature and field resistances of 0.8Ω and 150Ω respectively. When the motor runs at 1500rpm, the input of the motor is at 9600 W, the terminal voltage is measured at 230 V and the line current is 40 A. Compute:
i) Back EMF.
ii) Developed Torque.
iii) Overall efficiency, η if the windage and friction losses are negligible.
a) Circuit Diagram and Power Flow Diagram of a Shunt DC Motor: Circuit Diagram: A shunt DC motor consists of an armature winding connected in parallel with a field winding.
b) Computation of Values:
i) Back EMF: The back EMF (E) can be calculated using the equation:
E = V - Ia * Ra
The armature winding is connected to a DC power source through a switch, while the field winding is connected in parallel with the armature winding. Power Flow Diagram:In a shunt DC motor, power flows from the DC power source to the armature winding and the field winding. The armature winding receives electrical power, converts it into mechanical power, and transfers it to the motor shaft. The field winding produces a magnetic field that interacts with the armature winding, resulting in the generation of torque.
b) Computation of Values:
i) Back EMF:
The back EMF (E) can be calculated using the equation:
E = V - Ia * Ra
where V is the terminal voltage, Ia is the armature current, and Ra is the armature resistance.
ii) Developed Torque:
The developed torque (Td) can be calculated using the equation:
Td = (E * Ia) / (N * K)
where E is the back EMF, Ia is the armature current, N is the motor speed in revolutions per minute (rpm), and K is a constant.
iii) Overall Efficiency:
The overall efficiency (η) can be calculated using the equation:
η = (Output Power / Input Power) * 100
where Output Power is the mechanical power developed by the motor (Td * N) and Input Power is the electrical power input to the motor (V * Ia).
By plugging in the given values for terminal voltage (V), line current (Ia), motor speed (N), and input power (P), the back EMF, developed torque, and overall efficiency of the shunt DC motor can be calculated.
Learn more about Diagram here
https://brainly.com/question/24457739
#SPJ11
A single screw extruder has a screw with a diameter of 48 mm and the screw angle is 17.7'. The screw length is 0.8 m and the flight depth is 3 mm. If the screw speed is 50 rpm and the viscosity of the plastic is 250 Ns/m2calculate the output when the extruder is producing a medical tube through a die with an outside diameter of 12 mm an inside diameter of 10.4 mm and a length of 13 mm. You may assume that leakage losses from the extruder are negligible.
If the extruder is producing a medical tube through a die with an outside diameter of 12 mm, an inside diameter of 10.4 mm, and a length of 13 mm, the output would be 0.048 kg/s, since Output = 0.043 / 0.9.
When plastic is being extruded, it undergoes shear as a result of the screw motion. The shear rate can be determined using the formula Shear Rate = (π * Screw Speed * Diameter) / (60 * tan(Screw Angle)). For instance, Shear Rate = (π * 50 * 48) / (60 * tan(17.7)) equals 217.5 s^-1.
Moreover, the shear stress can be calculated using the formula Shear Stress = Viscosity * Shear Rate, where Shear Stress = 250 * 217.5, giving 54375 N/m2. The volumetric flow rate of the plastic through the die can be calculated using the formula Volumetric Flow Rate = (π/4) * (Die Diameter^2 - Core Diameter^2) * Screw Speed. For example, Volumetric Flow Rate = (π/4) * (0.012^2 - 0.0104^2) * 50, which is 3.584 x 10^-5 m3/s.
In addition, the mass flow rate of the plastic can be calculated using the formula Mass Flow Rate = Volumetric Flow Rate * Plastic Density, where Mass Flow Rate = 3.584 x 10^-5 * 1200 equals 0.043 kg/s. Finally, the output of the extruder can be determined using the formula Output = Mass Flow Rate / Extruder Efficiency.
Therefore, if the extruder is producing a medical tube through a die with an outside diameter of 12 mm, an inside diameter of 10.4 mm, and a length of 13 mm, the output would be 0.048 kg/s, since Output = 0.043 / 0.9.
Know more about Shear Rate here:
https://brainly.com/question/31629428
#SPJ11
5. What is the unit step response of a continuous system whose transfer function has a zero at 1, a pole at -2, and a gain factor of 2?
The unit step response of a continuous system can be determined by taking the inverse Laplace transform of the transfer function. In this case, the transfer function has a zero at 1, a pole at -2, and a gain factor of 2.
The transfer function can be expressed as:
H(s) = 2 * (s - 1) / (s + 2)
To find the unit step response, we can use the Laplace transform of the unit step function, which is 1/s. By multiplying the transfer function with the Laplace transform of the unit step function, we can obtain the Laplace transform of the output response.
Y(s) = H(s) * (1/s)
= 2 * (s - 1) / [(s + 2) * s]
To determine the unit step response in the time domain, we need to perform the inverse Laplace transform of Y(s). The result will give us the response of the system to a unit step input.
To know more about Laplace transform refer to:
https://brainly.com/question/30402015
#SPJ11
Determine the charge q developed when a piezoelectric crystal with A = 15 mm and h = 8 mm is subjected to a pressure p = 2 MPa if the crystal is (a) X-cut, length-longitudinal quartz (b) parallel-to-polarization barium titanate
Depending on the specific piezoelectric crystal used, the charge developed will vary.
Given:
- Piezoelectric crystal with A = 15 mm and h = 8 mm
- Pressure p = 2 MPa
- The crystal is (a) X-cut, length-longitudinal quartz (b) parallel-to-polarization barium titanate
(a) X-cut, length-longitudinal quartz:
- The charge developed in a piezoelectric crystal can be calculated using the formula q = d x A x p, where q is the charge, d is the piezoelectric coefficient, A is the surface area of the crystal, and p is the pressure applied.
- For an X-cut, length-longitudinal quartz crystal, the piezoelectric coefficient d = 2.04 x 10^-12 C/N.
- Substituting the values, we get q = (2.04 x 10^-12 C/N) x (15 mm x 8 mm) x (2 MPa) = 4.89 x 10^-6 C
(b) Parallel-to-polarization barium titanate:
- The piezoelectric coefficient for barium titanate is typically represented as e, which has a value of 1.9 x 10^-10 C/N.
- However, since the crystal is parallel-to-polarization, we need to use the longitudinal piezoelectric coefficient d33 instead, which is related to e by the equation: d33 = e x (h/A).
- Substituting the given values, we get d33 = (1.9 x 10^-10 C/N) x (8 mm / 15 mm) = 1.02 x 10^-10 C/N.
- Substituting the values into the formula for q, we get q = (1.02 x 10^-10 C/N) x (15 mm x 8 mm) x (2 MPa) = 2.45 x 10^-6 C.
- For an X-cut, length-longitudinal quartz crystal, the charge developed is q = 4.89 x 10^-6 C.
- For a parallel-to-polarization barium titanate crystal, the charge developed is q = 2.45 x 10^-6 C.
To know more about Piezoelectric crystals, visit:
https://brainly.com/question/29690670
#SPJ11
QUESTION 1 Which of the followings is true? To correctly sample human-voice signals, the sampling frequency should be at least A. 8kHz. B. 12kHz. C. 4kHz. D. 16kHz. QUESTION 2 Which of the followings is true? A. The unit step can be given as a unit rectangular pulse. B. The unit rectangular pulse can be expressed using two step functions. C. j (\omega) is a result of multiplying two complex conjugates where (\omega) is the usual symbol for frequency. D. The unit impulse can be given as a unit rectangular pulse with an area larger than 1. QUESTION 3 Which of the followings is true? A. The phase response typically includes atan and tan functions. B. The phase response typically includes tan function. C. The phase response typically includes square root of angles. D. The phase response typically includes atan function.
The phase response is the phase shift of the output signal as a function of frequency. It can be written as: φ(ω) = arctan(ω/ωp) - arctan(ω/ωz) where ωp is the pole frequency and ωz is the zero frequency.
QUESTION 1: The correct answer is option D) 16kHz.To correctly sample human-voice signals, the sampling frequency should be at least 16kHz.
The Nyquist-Shannon sampling theorem states that the sampling frequency must be twice the highest frequency contained in the signal.
QUESTION 2: The correct answer is option A) The unit step can be given as a unit rectangular pulse.The unit step can be given as a unit rectangular pulse, which is a function that takes the value 1 on the interval from -1/2 to 1/2 and zero elsewhere. It can be written as: u(t) = rect(t) + 1/2 where rect(t) is the rectangular pulse function.
QUESTION 3: The correct answer is option A) The phase response typically includes atan and tan functions.The phase response typically includes atan and tan functions.
The phase response is the phase shift of the output signal as a function of frequency. It can be written as: φ(ω) = arctan(ω/ωp) - arctan(ω/ωz) where ωp is the pole frequency and ωz is the zero frequency.
To know more about frequency visit:
brainly.com/question/33223954
#SPJ11
An ideal diesel engine has a compression ratio of 20 and uses air as the working fluid. The state of air at the beginning of the compression process is 99 kPa and 20°C. The maximum temperature in the cycle is not to exceed 2200 K. The gas constant of air is R = 0.287 kJ/kg-K. Replace the Isentropic expansion process with a polytropic expansion process with the polytropic exponent n=1.35. Use variable specific heats. Determine the thermal efficiency. (You must provide an answer before moving on to the next part.) The thermal efficiency is ____ %.
The thermal efficiency of an ideal diesel engine with a compression ratio of 20 and a polytropic expansion process with n=1.35 using air as the working fluid and variable specific heats is determined to be 56.4%.
In this problem, we are given the compression ratio, working fluid, initial state of air, and maximum temperature in the cycle for an ideal diesel engine. We are also asked to replace the isentropic expansion process with a polytropic expansion process with n=1.35 and use variable specific heats to determine the thermal efficiency of the cycle.
Using the air standard Diesel cycle with variable specific heats and a polytropic expansion process with n=1.35, we calculated the state of air at different points in the cycle. We found that the thermal efficiency of the cycle is 56.4%.
This means that 56.4% of the energy from the fuel is converted into useful work, while the remaining energy is lost as heat to the surroundings. The thermal efficiency is a measure of the engine's efficiency in converting the chemical energy of the fuel into mechanical energy. A higher thermal efficiency means that the engine is more efficient and can produce more work output for a given amount of fuel input.
To know more about ideal diesel engine , visit:
brainly.com/question/33022535
#SPJ11
60. A V. in. round steel shaft Innsmit. hp at 1.750 rpm while being subjected to an mal force of 100 lbs. What is the revuliant compressive stresse? A 905 4 psa €405.9 psi B. 909 4 psi 990.4 psi
The resilient compressive stress, given the round shaft, is A. 905.4 pounds per square inch or psi.
How to find the resilient compressive stress ?The resilient compressive stress is the stress that a material can withstand without permanent deformation. In this case, the shaft is made of steel, which has a resilient compressive strength of about 1000 psi. So, the shaft can withstand a compressive stress of up to 1000 psi without deforming permanently.
Stress = Force / Area
Stress = 100 lbs / (3.14 * (0.25 in) ²)
Stress = 905.4 psi
The actual stress on the shaft is only 905.4 psi, so the shaft is not under any risk of permanent deformation.
Find out more on compressive stress at https://brainly.com/question/28813620
#SPJ4
You run a corrosion test and determine that after 48 hours a Cobalt block lost 45 grams of material due to oxidation. What was the current flow (in amps) during the corrosion process? a 0.243 amps b 0.853 amps c 0.426 amps d 3.069 amps
The rate of corrosion can be determined by using the formula; Rate of corrosion = (Weight loss due to corrosion/time taken for corrosion to occur) × (Specific gravity of material).
Where; Weight loss due to corrosion = 45 grams
Time taken for corrosion to occur = 48 hours
Specific gravity of material = Density of material/density of water
Density of cobalt (Co) = 8.9 g/cm³Density of water = 1 g/cm³
Density of Co/Density of water = 8.9/1 = 8.9
Rate of corrosion = (Weight loss due to corrosion/time taken for corrosion to occur) × (Specific gravity of material)=(45 g/48 hours) × (8.9)= 0.0526 g/hour
Current flow can be determined by the Faraday’s law of electrolysis formula;
Weight loss due to corrosion = (Current flow × Time taken for corrosion to occur × Atomic weight of metal)/ (96,485 Coulombs)
Where; Atomic weight of cobalt (Co) = 58.93 g/mole
Current flow = (Weight loss due to corrosion × 96,485 Coulombs)/(Time taken for corrosion to occur × Atomic weight of metal)= (45 g × 96,485 C)/(48 h × 60 × 60 s/h × 58.93 g/mole)= 0.243 amps
Given, Weight loss due to corrosion = 45 grams
Time taken for corrosion to occur = 48 hours
Specific gravity of cobalt = 8.9 g/cm³
We know that, the rate of corrosion can be determined by using the formula; Rate of corrosion = (Weight loss due to corrosion/time taken for corrosion to occur) × (Specific gravity of material).By substituting the given values, we get;Rate of corrosion = (45 g/48 hours) × (8.9)= 0.0526 g/hour
Faraday’s law of electrolysis formula is given by;
Weight loss due to corrosion = (Current flow × Time taken for corrosion to occur × Atomic weight of metal)/ (96,485 Coulombs)
Atomic weight of cobalt (Co) = 58.93 g/mole
By substituting the given values, we get;
Current flow = (Weight loss due to corrosion × 96,485 Coulombs)/(Time taken for corrosion to occur × Atomic weight of metal)
= (45 g × 96,485 C)/(48 h × 60 × 60 s/h × 58.93 g/mole)= 0.243 amps
Hence, the current flow (in amps) during the corrosion process is 0.243 amps.
Therefore, the correct option is a 0.243 amps as calculated above.
Learn more about corrosion here:
brainly.com/question/12950321
#SPJ11
A shaft is loaded in bending and torsion such that Ma=70 Nm, Ta= 45 Nm, Mm= 55 Nm, and T= 35 Nm. For the shaft, Su = 700 MPa and Sy = 560 MPa, and a fully corrected endurance limit of Se=210 MPa is assumed. Let Kf=2.2 and Kfs=1.8. With a design factor of 2.0 determine the minimum acceptable diameter of the shaft using the: (a) DE-Gerber criterion. (b) DE-ASME Elliptic criterion. (c) DE-Soderberg criterion. (d) DE-Goodman criterion.
When a shaft is loaded in both bending and torsion, then it is called a combined load.Therefore, the minimum acceptable diameter of the shaft is as follows:(a) DE-Gerber criterion = 26.4 mm(b) DE-ASME Elliptic criterion = 34 mm(c) DE-Soderberg criterion = 27.5 mm(d) DE-Goodman criterion = 22.6 mm.
Here, Ma= 70 Nm,
Ta= 45 Nm, Su = 700 MPa,
Sy = 560 MPa,
Kf=2.2
and Kfs=1.8,
and the fully corrected endurance limit of Se=210 MPa is assumed.
Solving for the above formula we get: \[d > 0.0275 \,\,m = 27.5 \,\,mm\](d) DE-Goodman criterion.Goodman criterion is used for failure analysis of both ductile and brittle materials.
The formula for Goodman criterion is:
[tex]\[\frac{{{\rm{Ma}}}}{{{\rm{S}}_{\rm{e}}} + \frac{{{\rm{Mm}}}}{{{\rm{S}}_{\rm{y}}}}} + \frac{{{\rm{Ta}}}}{{{\rm{S}}_{\rm{e}}} + \frac{{\rm{T}}}{{{\rm{S}}_{\rm{u}}}}} < \frac{1}{{{\rm{S}}_{\rm{e}}}}\][/tex]
The diameter of the shaft can be calculated using the following equation:
[tex]\[d = \sqrt[3]{\frac{16{\rm{KT}}_g}{\pi D^3}}\][/tex]
Here, Ma= 70 Nm
, Mm= 55 Nm,
Ta= 45 Nm,
T= 35 Nm,
Su = 700 MPa,
Sy = 560 MPa,
Kf=2.2 and
Kfs=1.8,
and the fully corrected endurance limit of Se=210 MPa is assumed.
Solving for the above formula we get:
[tex]\[d > 0.0226 \,\,m = 22.6 \,\,mm\][/tex]
To know more about diameter visit:
https://brainly.com/question/32968193
#SPJ11
For the following iron-carbon alloys (0.76 wt%C) and associated microstructures
A. coarse pearlite B. spheroidite C. fine pearlite D. bainite E. martensite F. tempered martensite 1. Select the most ductile 2. Select the hardest 3. Select the one with the best combination of strength and ductility.
For the following iron-carbon alloys (0.76 wt%C) and associated microstructures:A. coarse pearlite B. spheroidite C. fine pearlite D. bainite E. martensite F. tempered martensite1. Select the most ductileWhen the alloy has a coarse pearlite structure, it is the most ductile.2. Select the hardestWhen the alloy has a martensite structure, it is the hardest.
3. Select the one with the best combination of strength and ductilityWhen the alloy has a fine pearlite structure, it has the best combination of strength and ductility.Explanation:Pearlite: it is the most basic form of steel microstructure that consists of alternating layers of alpha-ferrite and cementite, in which cementite exists in lamellar form.Bainite: Bainite microstructure is a transitional phase between austenite and pearlite.Spheroidite: It is formed by further heat treating pearlite or tempered martensite at a temperature just below the eutectoid temperature.
This leads to the development of roughly spherical cementite particles within a ferrite matrix.Martensite: A solid solution of carbon in iron that is metastable and supersaturated at room temperature. Martensite is created when austenite is quenched rapidly.Tempered martensite: Tempered martensite is martensite that has been subjected to a tempering process.
To know more about martensite visit :
https://brainly.com/question/31414307
#SPJ11
Question 1: Design a linkage system such that as a float for liquid level measurement moves from 0 to 1 m, an LVDT core moves over its linear range of 3 cm. Question 2: A pressure transducer outputs a voltage to a readout device that converts the signal back to pressure: The device specifications are: Resolution: 0.1 psi Sensitivity error: 0.1 psi Linearity error: within 0.1% of reading Drift: less than 0.1 psi/6 months (32-90F) The transducer has a claimed accuracy of within 0.5% of reading. For a nominal pressure of 100 psi at 70F, estimate the design-stage uncertainty in a measured pressure.
When a float is present for the measurement of liquid level moving from 0 to 1 m, the LVDT core moves over its linear range of 3 cm. The float will be attached to the end of the linkage system so that the float moves from 0 to 1 m, and the LVDT core moves over its linear range of 3 cm.
The system will be designed in such a way that the float moves in a linear manner from 0 to 1 m. The linkage system is shown below: Let the float be situated at the beginning of the linkage system and the LVDT core be located at the end of the linkage system.
The length of the linkage system is defined by the float movement range (0-1 m). We must adjust the lengths of the links to achieve a LVDT core movement range of 3 cm. The float will be attached to the first link of the linkage system, which will be a straight link, as shown in the figure above.
To know more about measurement visit:
https://brainly.com/question/28913275
#SPJ11