Answers
resistor in series add so the total resistance is 12 ohms
E=I x R E = voltage, I = amps, R = resistance
12 = I x 12
I=1 is the answer to the question
E=I x R E = voltage, I = amps, R = resistance
12 = I x 12
I=1 is the correct answer is the correct answer to the question
Related Questions
A bouncing belt tensioner indicates what
Answers
Answer:
worn down tensioner
Explanation:
when your belt tensioner is bouncing it is worn out the tensioner belt pulley arm is worn out due to a spring that has gone bad this will cause the tensioner to bounce you will want to replace the belt tensioner
4x+2y=20 -8x-3y=16 what is y
Answers
Answer:
y = 56
Explanation:
We label each of the given equations as follows;
4·x + 2·y = 20...(1)
-8·x - 3·y = 16...(2)
Therefore, we are given a simultaneous equation, question
We make 'x' the subject of both equations and equate the result to find the value of 'y' as follows;
For equation (1)
4·x + 2·y = 20
∴ x = (20 - 2·y)/4 = 5 - y/2
x = 5 - y/2
For equation (2), we have;
-8·x - 3·y = 16
∴ x = (16 + 3·y)/(-8) = -2 - 3·y/8
x = -2 - 3·y/8
Equating the two equations of 'x', gives;
5 - y/2 = -2 - 3·y/8
7 = y/2 - 3·y/8 = (4·y - 3·y)/8 = y/8
∴ 7 = y/8
y = 7 × 8 = 56
y = 56
LEARNING ACTIVITY SHEET
Bantayan National High School
EIM 11- Summative Test for Q2 Week 3&4
Name:
Year and Section :
A. Direction: Select from he given choices the best answer. Write only the corresponding letter as your answer in the blank provided before the
number. Use this paper as your answer sheet.
1. It is used to test/check the continuity of the circuit.
a. Ohmmeter b. Ammeter c. Voltmetdewer d. Wattmeter
2. Is a physical device used to connect electronic test equipment to a device under test.
a. Test probes
b. Plug
c. Pen tester d. None of these
3. A device inserted to a convenience outlet to conduct electric current.
a. Plug b. Continuity tester c. Test light d. None of these
4. Is a stranded wire used to temporary wiring installation and commonly used in extension cord assembly.
a. Duplex cord
b. Plug
c. Bulb guard d. None of these
5. It is a pocket size tool used to test the line wire or circuit if there is a current in it.
a. Test light
b. Plug
c. Continuity tester d. None of these
6. An instrument used to measure the amount of electrical current intensity in a circuit.
a.) voltmeter b.)ammeter c.) micrometer d.) ohmmeter
7. A pocket-sized tool used to test the line wire or circuit if there is current in it.
a.) test light
b.) wire gauge
c.) ruler
d.) pull-push rule
8. A measuring tool used to measure the length of an object in centimeter in it.
a.) test light
b.) wire gauge
c.) ruler
d.) pull-push rule
9. It is used to measure the diameter of wires/ conductors in circular mils. It can measure small and big
sizes of wires and cables.
a.) voltmeter b.)ammeter c.) micrometer d.) ohmmeter
10. It is used to measure the voltage, resistance and current of a circuit. It is connected in parallel or series with the
circuit depending on what to measure.
a.) volt-ohm-milliameter b.) micrometer c.) ohmmeter d.) ammeter
11. It is a measuring tool used to measure length, width and thickness of short flat object and in sketching straight
linae
Answers
Answer:
1. It is used to test/check the continuity of the circuit
a. Ohmmeter
2. Is a physical device used to connect electronic test equipment to a device under test
a. Test probes
3. A device inserted to a convenience outlet to conduct electric current
a. Plug
4. Is a stranded wire used to temporary wiring installation and commonly used in extension cord assembly
a. Duplex cord
5. It is a pocket size tool used to test the line wire or circuit if there is a current in it.
a. Test light
6. An instrument used to measure the amount of electrical current intensity in a circuit
b. Ammeter
7. A pocket sized tool used to test the line wire or circuit if there is current in it.
a. Test light
8. A measuring tool used to measure the length of an object in centimeter in it
b) Ruler
9. It is used to measure the diameter of wires/conductors in circular mills. It can measure small and big sizes of wires
a. Micrometer
10. It is used to measure the voltage, resistance and current of a circuit. It is connected in parallel or series with the circuit depending on what to measure
a) Volt-Ohm-milliammeter
11. It is the measuring tool used to measure length, width and thickness of short object and in sketching straight line
Foot rule/ ruler
Explanation:
1. An Ohmmeter tests resistance of a circuit and therefore, indicates if the circuit has continuity (connectivity) by measuring the resistance to the current it sends through the circuit, while the circuit power is switched off
2. A test probe connects a testing equipment to a Device Under Test (DUT)
3. A plug is used to connect an electric appliance to the mains power supply by fitting it into the mains power outlet
4. A duplex cord is used for temporary wiring to supply power in an extension cord assembly
5. A test light is used to determine if a circuit has electric current flowing in it
6. An ammeter measures the amount of direct or alternating current flowing in a circuit
7. Test light is used to check the presence of an electric current in a circuit
8. A ruler is used to measure length and it is marked in cm or in
9. A micrometer measures the diameter of wires placed in between the anvil and spindle
10. A Volt-Ohm-Milliammeter (VOM), is also known as a multimeter that measures voltage, current, and resistance of a circuit
11. A foot rule/ ruler, measures the dimensions of objects that are flat and short
What type of engineering do you think would help solve this SDG???
Answers
Answer:
Explanation:
Planning engineering
I NEED HELP ASAP
I DONT KNOW THE ANSWER
TO THIS
PLEASE HELP THIS IS IN EDGINUITY IN SOCIAL STUDIES
Answers
Answer:
A is continental polar and B Is maritime polar
Point A : continental polar
Point B : maritime tropical
⚠️I mark BRIANLIST ⚠️The same engineering teams are able to design and develop the different subsystems for an airplane.
O True
O False
Answers
Answer:
False
Explanation:
Are we living in a simulation!
True
False
Answers
i would hope:):):)
I am happy to solve more
25 Points
In no less than one hundred fifty words, explain how microstructures reduce friction within fluid power systems. Mention some of the benefits of designing with microstructures.
Answers
Answer:
The functional surface on the microstructures reduces the friction. Below the functional surface, the layer surface will be there. It also reduces friction. The microstructures on the functional surface act as an oil reservoir and it produces the oil. It is well known that friction between lubricated surfaces is a chief source of energy Now, help is on the way due to research taking place within the Engineering Research Center for Compact and Efficient Fluid speed and lubricant type, and then choose the optimal microstructures.
Explanation: