When a light ray passes from one medium to another, it undergoes refraction, which is the bending of the light ray due to the change in the speed of light in different mediums. The refracted light ray is bent towards or away from the normal depending on the relative speeds of light in the two mediums. If the speed of light decreases as it passes from medium 1 to medium 2, the refracted light ray will bend towards the normal.
Refraction occurs because the speed of light changes when it travels from one medium to another with a different optical density. The refracted light ray is determined by Snell's law, which states that the ratio of the sines of the angles of incidence (θ₁) and refraction (θ₂) is equal to the ratio of the speeds of light in the two mediums (v₁ and v₂):
sin(θ₁)/sin(θ₂) = v₁/v₂
When the speed of light decreases as it passes from medium 1 to medium 2, the refracted light ray bends towards the normal. The angle of refraction (θ₂) will be smaller than the angle of incidence (θ₁), resulting in the light ray bending closer to the perpendicular line to the surface of separation between the two mediums. This behavior is governed by Snell's law and is a fundamental principle of optics.
To learn more about Snell's law - brainly.com/question/31432930
#SPJ11
1. A ball is kicked horizontally at 8 m/s30 degrees above the horizontal. How far does the ball travel before hitting the ground? (2pts) 2. A shell is fired from a cliff horizontally with initial velocity of 800 m/s at a target on the ground 150 m below. How far away is the target? (2 pts) 3. You are standing 50 feet from a building and throw a ball through a window that is 26 feet above the ground. Your release point is 6 feet off of the ground (hint: you are only concerned with Δy ). You throw the ball at 30ft/sec. At what angle from the horizontal should you throw the ball? (hint: this is your launch angle) ( 2 pts) 4. A golfer drives a golf ball from the tee down the fairway in a high arcing shot. When the ball is at the highest point during the flight: ( 1pt) a. The velocity and acceleration are both zero b. The x-velocity is zero and the y-velocity is zero c. The x-velocity is non-zero but the y-velocity is zero d. The velocity is non-zero but the acceleration is zero
1) Distance = 9.23 m ; 2) Horizontal distance = 24,481.7 m ; 3) θ = 33.2 degrees ; 4) When the ball is at the highest point during the flight, a) the velocity and acceleration are both zero and hence option a) is the correct answer.
1. The horizontal component of the ball's velocity is 8cos30, and the vertical component of its velocity is 8sin30. The ball's flight time can be determined using the vertical component of its velocity.
Using the formula v = u + at and assuming that the initial vertical velocity is 8sin30, the acceleration is 9.81 m/s² (acceleration due to gravity), and the final velocity is zero (because the ball is at its maximum height), the time taken to reach the maximum height can be calculated.
The ball will reach its maximum height after half of its flight time has elapsed, so double the time calculated previously to get the total time. Substitute the time calculated previously into the horizontal velocity formula to get the distance the ball travels horizontally before landing.
Distance = 8cos30 x 2 x [8sin30/9.81] = 9.23 m
Answer: 9.23 m
2. Using the formula v = u + gt, the time taken for the shell to hit the ground can be calculated by assuming that the initial vertical velocity is zero (since the shell is fired horizontally) and that the acceleration is 9.81 m/s². The calculated time can then be substituted into the horizontal distance formula to determine the distance the shell travels horizontally before hitting the ground.
Horizontal distance = 800 x [2 x 150/9.81]
= 24,481.7 m
Answer: 24,481.7 m³.
3) To determine the angle at which the ball should be thrown, the vertical displacement of the ball from the release point to the window can be used along with the initial velocity of the ball and the acceleration due to gravity.
Using the formula v² = u² + 2as and assuming that the initial vertical velocity is 30sinθ, the acceleration due to gravity is -32.2 ft/s² (because the acceleration due to gravity is downwards), the final vertical velocity is zero (because the ball reaches its highest point at the window), and the displacement is 20 feet (26-6), the angle θ can be calculated.
Angle θ = arc sin[g x (20/900 + 1/2)]/2, where g = 32.2 ft/s²
Answer: θ = 33.2 degrees
4. A golfer drives a golf ball from the tee down the fairway in a high arcing shot. When the ball is at the highest point during the flight, the velocity and acceleration are both zero. (1pt)
Answer: a. The velocity and acceleration are both zero. Thus, option a) is correct.
To know more about Horizontal distance, refer
https://brainly.com/question/31169277
#SPJ11
(a) Calculate the classical momentum of a proton traveling at 0.979c, neglecting relativistic effects. (Use 1.67 ✕ 10−27 for the mass of the proton.)
(b) Repeat the calculation while including relativistic effects.
(c) Does it make sense to neglect relativity at such speeds?
yes or no
No, it does not make sense to neglect relativistic effects at speeds close to the speed of light. Neglecting relativity would lead to an incorrect estimation of the momentum of a proton traveling at 0.979c. Including relativistic effects is essential to accurately calculate the momentum in such scenarios.
(a) Neglecting relativistic effects:
To calculate the classical momentum of a proton without considering relativity, we can use the formula for classical momentum:
p = mv
where p is the momentum, m is the mass of the proton, and v is its velocity. Substituting the given values, we have:
m = 1.67 × 10^(-27) kg (mass of the proton)
v = 0.979c (velocity of the proton)
p = (1.67 × 10^(-27) kg) × (0.979c)
Calculating the numerical value, we obtain the classical momentum of the proton without considering relativistic effects.
(b) Including relativistic effects:
When speed approach the speed of light, classical physics is inadequate, and we must account for relativistic effects. In relativity, the momentum of a particle is given by:
p = γmv
where γ is the Lorentz factor and is defined as γ = 1 / sqrt(1 - (v^2/c^2)), where c is the speed of light in a vacuum.
Considering the same values as before and using the Lorentz factor, we can calculate the relativistic momentum of the proton.
(c) Does it make sense to neglect relativity at such speeds?
No, it does not make sense to neglect relativity at speeds close to the speed of light. At high velocities, relativistic effects become significant, altering the behavior of particles. Neglecting relativity in calculations would lead to incorrect predictions and inaccurate results. To accurately describe the momentum of particles traveling at relativistic speeds, it is essential to include relativistic effects in the calculations.
Learn more about speed of light here:
brainly.com/question/28224010
#SPJ11
(a) The classical momentum of a proton traveling at 0.979c, neglecting relativistic effects, can be calculated using the formula p = mv. Given the mass of the proton as 1.67 × 10^(-27) kg, the momentum is 3.28 × 10^(-19) kg·m/s.
(b) When including relativistic effects, the momentum calculation requires the relativistic mass of the proton, which increases with velocity. The relativistic mass can be calculated using the formula m_rel = γm, where γ is the Lorentz factor given by γ = 1/sqrt(1 - (v/c)^2). Using the relativistic mass, the momentum is calculated as p_rel = m_rel * v. At 0.979c, the relativistic momentum is 4.03 × 10^(-19) kg·m/s.
(c) No, it does not make sense to neglect relativity at such speeds because relativistic effects become significant as the velocity approaches the speed of light. Neglecting relativistic effects would lead to inaccurate results, as demonstrated by the difference in momentum calculated with and without considering relativity in this example.
Explanation:
(a) The classical momentum of an object is given by the product of its mass and velocity, according to the formula p = mv. In this case, the mass of the proton is given as 1.67 × 10^(-27) kg, and the velocity is 0.979c, where c is the speed of light. Plugging these values into the formula, the classical momentum of the proton is found to be 3.28 × 10^(-19) kg·m/s.
(b) When traveling at relativistic speeds, the mass of an object increases due to relativistic effects. The relativistic mass of an object can be calculated using the formula m_rel = γm, where γ is the Lorentz factor. The Lorentz factor is given by γ = 1/sqrt(1 - (v/c)^2), where v is the velocity and c is the speed of light. In this case, the Lorentz factor is calculated to be 3.08. Multiplying the relativistic mass by the velocity, the relativistic momentum of the proton traveling at 0.979c is found to be 4.03 × 10^(-19) kg·m/s.
(c) It does not make sense to neglect relativity at such speeds because as the velocity approaches the speed of light, relativistic effects become increasingly significant. Neglecting these effects would lead to inaccurate calculations. In this example, we observe a notable difference between the classical momentum and the relativistic momentum of the proton. Neglecting relativity would underestimate the momentum and fail to capture the full picture of the proton's behavior at high velocities. Therefore, it is crucial to consider relativistic effects when dealing with speeds approaching the speed of light.
Learn more about speed of light here:
brainly.com/question/29216893
#SPJ11
if your body temperature is 38°C and you're giving us given off the greatest amount of infrared light at frequency of 4.2x10^13 Hz.
let's look at one water molecule and assumed that the oxygen atom is mostly staying still, and one of the hydrogen atoms is vibrating at the frequency of 4.2x10^13 Hz. we can model this oscillation as a mass on a spring. It hydrogen atom is just a proton and an electron.
1a. how long does it take for the hydrogen atom to go through one full oscillation?
2a. what is the spring constant?
3a. what is the amplitude of the oscillation?
4a. what is the hydrogen atoms maximum speed while it's oscillating?
2.38 × 10−14 s. This time is taken by the hydrogen atom to complete one oscillation.
Given: Body temperature = 38°C
= 311 K;
Frequency = 4.2 × 1013 Hz.
Let's consider a hydrogen atom vibrating at the given frequency.1a. The time period is given by:
T = 1/f
=1/4.2 × 1013
=2.38 × 10−14 s.
This time is taken by the hydrogen atom to complete one oscillation.
2a. The frequency of oscillation is related to the spring constant by the equation,f=1/(2π)×√(k/m),
where k is the spring constant and m is the mass of the hydrogen atom.Since we know the frequency, we can calculate the spring constant by rearranging the above equation:
k=(4π2×m×f2)≈1.43 × 10−2 N/m.
3a. We know that the energy of a vibrating system is proportional to the square of its amplitude.
Mathematically,E ∝ A2.
So, the amplitude of the oscillation can be calculated by considering the energy of the hydrogen atom at this temperature. It is found to be
2.5 × 10−21 J.
4a. The velocity of a vibrating system is given by,
v = A × 2π × f.
Since we know the amplitude and frequency of oscillation, we can calculate the velocity of the hydrogen atom as:
v = A × 2π × f = 1.68 × 10−6 m/s.
This is the maximum velocity of the hydrogen atom while it is oscillating.
To know more about temperature visit;
brainly.com/question/7510619
#SPJ11
: 4. Given that the energy in the world is virtually constant, why do we sometimes have an "energy crisis"? 5a What is the ultimate end result of energy transformations. That is, what is the final form that most energy types eventually transform into? 5b What are the environmental concerns of your answer to 5a?
Energy refers to the capacity or ability to do work or produce a change. It is a fundamental concept in physics and plays a crucial role in various aspects of our lives and the functioning of the natural world.
4. Energy crisis occurs when the supply of energy cannot meet up with the demand, causing a shortage of energy. Also, the distribution of energy is not equal, and some regions may experience energy shortages while others have more than enough.
5a. The ultimate end result of energy transformations is heat. Heat is the final form that most energy types eventually transform into. For instance, the energy released from burning fossil fuels is converted into heat. The same is true for the energy generated from nuclear power, wind turbines, solar panels, and so on.
5b. Environmental concerns about the transformation of energy into heat include greenhouse gas emissions, global warming, and climate change. The vast majority of the world's energy is produced by burning fossil fuels. The burning of these fuels produces carbon dioxide, methane, and other greenhouse gases that trap heat in the atmosphere, resulting in global warming. Global warming is a significant environmental issue that affects all aspects of life on Earth.
To know more about Energy visit:
https://brainly.com/question/30672691
#SPJ11
What If? The two capacitors of Problem 13 (C₁ = 5.00σF and C₂ =12.0 σF ) are now connected in series and to a 9.00-V battery. Find(c) the charge on each capacitor.
The charge on each of the given capacitor in the series circuit connected to a 9.00-V battery is found to be 45 μC for C₁ and 108 μC for C₂.
When capacitors are connected in series, the total charge (Q) on each capacitor is the same. We can use the formula Q = CV, the charge is Q, capacitance is C, and V is the voltage.
Given,
C₁ = 5.00 μF
C₂ = 12.0 μF
V = 9.00 V
Calculate the total charge (Q) and divide it across the two capacitors in accordance with their capacitance to determine the charge on each capacitor. Using the formula Q = CV, we find,
Q = C₁V = (5.00 μF)(9.00 V) = 45.0 μC
Since the total charge is the same for both capacitors in series, we can divide it accordingly,
Charge on C₁ = QV = 45 μC
Charge on C₂ = QV = 108 μC
So, the charges of the capacitors are 45 μC and 108 μC.
To know more about capacitance, visit,
https://brainly.com/question/30529897
#SPJ4
Let's say you have a standing wave on a fixed-open string (same as a closed-open pipe, a clarinet) with length L = 60 cm. The open boundary condition at x = L requires the spatial derivative of the displacement of the standing wave to vanish there. What is the wavelength in meters of this standing wave for the fundamental (lowest frequency) mode?
The wavelength of the standing wave for the fundamental mode on the fixed-open string or closed-open pipe with a length of 60 cm is 1.2 meters.
In a standing wave on a fixed-open string or a closed-open pipe, such as a clarinet, the open boundary condition at the end of the string (or pipe) requires the spatial derivative of the displacement of the standing wave to vanish. In other words, the amplitude of the wave must be zero at that point.
For the fundamental mode of a standing wave, also known as the first harmonic, the wavelength is twice the length of the string or pipe. In this case, the length L is given as 60 cm, which is equivalent to 0.6 meters.
Since the wavelength is twice the length, the wavelength of the fundamental mode in meters would be 2 times 0.6 meters, which equals 1.2 meters.
Therefore, the wavelength of this standing wave for the fundamental mode is 1.2 meters.
To learn more about wavelength
https://brainly.com/question/10750459
#SPJ11
20 At new moon, the Earth, Moon, and Sun are in line, as indicated in figure. Find the direction and the magnitude of the net gravitational force exerted on (a) Earth, (b) the Moon, and the Sun,
At new moon, the Earth, Moon, and Sun are in a straight line, with the Earth in the middle. The gravitational force exerted by the Sun on the Earth is greater than the gravitational force exerted by the Moon on the Earth, so the net gravitational force on the Earth points towards the Sun. The magnitude of the net gravitational force on the Earth is equal to the sum of the gravitational forces exerted by the Sun and the Moon on the Earth.
The gravitational force exerted by the Earth on the Moon is greater than the gravitational force exerted by the Sun on the Moon, so the net gravitational force on the Moon points towards the Earth. The magnitude of the net gravitational force on the Moon is equal to the sum of the gravitational forces exerted by the Earth and the Sun on the Moon.
The gravitational force exerted by the Moon on the Sun is much smaller than the gravitational force exerted by the other planets on the Sun, so the net gravitational force on the Sun is negligible.
The direction and magnitude of the net gravitational force exerted on each object are:
Earth: Points towards the Sun. Magnitude is equal to the sum of the gravitational forces exerted by the Sun and the Moon on the Earth.Moon: Points towards the Earth. Magnitude is equal to the sum of the gravitational forces exerted by the Earth and the Sun on the Moon.Sun: Negligible.To know more about the gravitational force refer here,
https://brainly.com/question/31808913#
#SPJ11
Complete question :
At new moon, the Earth, Moon, and Sun are in a line, as indicated in the figure(Figure 1) . A) Find the magnitude of the net gravitational force exerted on the Earth. B) Find the direction of the net gravitational force exerted on the Earth. Toward or Away from the Sun. C) Find the magnitude of the net gravitational force exerted on the Moon. D) Find the direction of the net gravitational force exerted on the Moon. Toward the Earth or Toward the Sun. E) Find the magnitude of the net gravitational force exerted on the Sun. F) Find the direction of the net gravitational force exerted on the Sun. Toward or away from the earth-moon system.
A uranium nucleus (mass 238 units) at rest decays into a helium nucleus (mass 4.0 units) and a thorium nucleus (mass 234 units). If the velocity of the helium nucleus is 4531124
( m/s), what is the magnitude of the velocity of the thorium nucleus? Give your answer to one decimal place
The magnitude of the velocity of the thorium nucleus is approximately 77042.4 m/s (rounded to one decimal place).
To solve this problem, we can use the principle of conservation of momentum. Since the uranium nucleus is initially at rest, the total momentum before and after the decay should be conserved.
Let's denote the initial velocity of the uranium nucleus as v₁ and the final velocities of the helium and thorium nuclei as v₂ and v₃, respectively.
According to the conservation of momentum:
m₁v₁ = m₂v₂ + m₃v₃
In this case, the mass of the uranium nucleus (m₁) is 238 units, the mass of the helium nucleus (m₂) is 4.0 units, and the mass of the thorium nucleus (m₃) is 234 units.
Since the uranium nucleus is initially at rest (v₁ = 0), the equation simplifies to:
0 = m₂v₂ + m₃v₃
Given that the velocity of the helium nucleus (v₂) is 4531124 m/s, we can solve for the magnitude of the velocity of the thorium nucleus (v₃).
0 = 4.0 × 4531124 + 234 × v₃
Simplifying the equation:
v₃ = - (4.0 × 4531124) / 234
Evaluating the expression:
v₃ = - 77042.4 m/s
To know more about velocity
https://brainly.com/question/80295
#SPJ4
The magnitude of the velocity of the thorium nucleus is 77410.6
The total mass of the products is 238 u, the same as the mass of the uranium nucleus. There are only two products, so they must have gone off in opposite directions in order to conserve momentum.
Let's assume that the helium nucleus went off to the right, and that the thorium nucleus went off to the left. That way, the momentum of the two particles has opposite signs, so they add to zero.
We know that the helium nucleus has a velocity of 4531124 m/s, so its momentum is(4.0 u)(4531124 m/s) = 1.81245e+13 kg m/s. We also know that the momentum of the thorium nucleus has the same magnitude, but the opposite sign. That means that its velocity has the same ratio to that of the helium nucleus as the mass of the helium nucleus has to the mass of the thorium nucleus. That ratio is(4.0 u)/(234.0 u) = 0.017094So the velocity of the thorium nucleus is(0.017094)(4531124 m/s) = 77410 m/s.
Answer: 77410.6
Learn more about magnitude
https://brainly.com/question/31022175
#SPJ11
For a certain p-n junction diode, the saturation current at room temperature (20°C) is 0.950 mA. Pall A What is the resistance of this diode when the voltage across it is 86.0 mV? Express your answer"
The resistance of the diode at a voltage of 86.0 mV is approximately 3.371 Ω.
The resistance (R) of a diode can be approximated using the Shockley diode equation:
I = Is * (exp(V / (n * [tex]V_t[/tex]) - 1)
Where:
I is the diode current,
Is is the saturation current,
V is the voltage across the diode,
n is the ideality factor, typically around 1 for a silicon diode,
[tex]V_t[/tex]is the thermal voltage, approximately 25.85 mV at room temperature (20°C).
In this case, we are given the saturation current (Is) as 0.950 mA and the voltage (V) as 86.0 mV.
Let's calculate the resistance using the given values:
I = 0.950 mA = 0.950 * 10⁻³A
V = 86.0 mV = 86.0 * 10⁻³ V
[tex]V_t[/tex] = 25.85 mV = 25.85 * 10⁻³ V
Using the Shockley diode equation, we can rearrange it to solve for the resistance:
R = V / I = V / (Is * (exp(V / (n * [tex]V_t[/tex])) - 1))
Substituting the given values:
R = (86.0 * 1010⁻³ V) / (0.950 * 10⁻³ A * (exp(86.0 * 10⁻³ V / (1 * 25.85 * 10⁻³ V)) - 1))
Let's simplify it step by step:
R = (86.0 * 10⁻³ V) / (0.950 * 10⁻³ A * (exp(86.0 * 10⁻³ V / (1 * 25.85 * 10⁻³ V)) - 1))
R = (86.0 * 10⁻³ V) / (0.950 * 10⁻³ A * (exp(3.327) - 1))
R = (86.0 * 10⁻³ V) / (0.950 * 10⁻³ A * (27.850 - 1))
R = (86.0 * 10⁻³ V) / (0.950 * 10⁻³ A * 26.850)
Now, we can simplify further:
R = (86.0 / 0.950) * (10⁻³ V / 10⁻³ A) / 26.850
R = 90.526 * 1 / 26.850
R ≈ 3.371 Ω
Therefore, the resistance of the diode at a voltage of 86.0 mV is approximately 3.371 Ω.
Learn more about Diode Current at
brainly.com/question/30548627
#SPJ4
During a certain time interval, the angular position of a swinging door is described by 0 = 4.96 + 10.10 + 2.01t2, where is in radians and t is in seconds. Determine the angular position, angular speed, and angular acceleration of the door at the following times. (a) t = 0 rad w = rad/s Trad/s2 a = (b) t = 2.92 s 0 = rad W= rad/s a = rad/s2
The given times:
(a) t = 0: θ = 4.96 radians, ω = 10.10 rad/s, α = 4.02 rad/s^2
(b) t = 2.92 s: θ ≈ 46.04 radians, ω ≈ 22.80 rad/s, α = 4.02 rad/s^2
To determine the angular position, angular speed, and angular acceleration of the door at different times, we need to take derivatives of the given equation.
The given equation is:
θ = 4.96 + 10.10t + 2.01t^2
Taking the derivative with respect to time (t), we get:
ω = dθ/dt = d/dt(4.96 + 10.10t + 2.01t^2)
Differentiating each term separately, we have:
ω = 0 + 10.10 + 2 * 2.01t
Simplifying, we get:
ω = 10.10 + 4.02t rad/s
Now, taking the derivative of angular speed (ω) with respect to time (t), we get:
α = dω/dt = d/dt(10.10 + 4.02t)
The derivative of a constant term is zero, so we have:
α = 0 + 4.02
Simplifying, we get:
α = 4.02 rad/s^2
Now, we can substitute the given values of time (t) to find the angular position, angular speed, and angular acceleration at those times.
(a) For t = 0:
θ = 4.96 + 10.10(0) + 2.01(0)^2
θ = 4.96 radians
ω = 10.10 + 4.02(0)
ω = 10.10 rad/s
α = 4.02 rad/s^2
(b) For t = 2.92 s:
θ = 4.96 + 10.10(2.92) + 2.01(2.92)^2
Calculating this value gives us:
θ ≈ 46.04 radians
ω = 10.10 + 4.02(2.92)
Calculating this value gives us:
ω ≈ 22.80 rad/s
α = 4.02 rad/s^2
To know more about Angular acceleration:
brainly.com/question/14769426
#SPJ11
An electron has a rest mass m0=9.11×10−31 kg. It moves with a speed v=0.700c. The speed of light in a vacuum c=3.00×108 m/s. An electron has a rest mass m0=9.11×10−31 kg. It moves with a speed v=0.700c. The speed of light in a vacuum c=3.00×108 m/s. Part A - Find its relativistic mass. Part B - What is the total energy E of the electron? ∇ Part C What is the relativistic kinetic energy KE of the electron? Use scientific notations, format 1.234∗10n. Unit is Joules.
The problem involves an electron with a rest mass of m0=9.11×10−31 kg moving with a speed v=0.700c, where c=3.00×108 m/s is the speed of light in a vacuum.
The goal is to calculate the relativistic mass of the electron (Part A), the total energy of the electron (Part B), and the relativistic kinetic energy of the electron (Part C).
Part A: The relativistic mass (m) of an object can be calculated using the formula m = m0 / sqrt(1 - v^2/c^2), where m0 is the rest mass, v is the velocity of the object, and c is the speed of light. Plugging in the given values, we can determine the relativistic mass of the electron.
Part B: The total energy (E) of the electron can be calculated using the relativistic energy equation, E = mc^2, where m is the relativistic mass and c is the speed of light. By substituting the previously calculated relativistic mass, we can find the total energy of the electron.
Part C: The relativistic kinetic energy (KE) of the electron can be determined by subtracting the rest energy (m0c^2) from the total energy (E). The rest energy is given by m0c^2, where m0 is the rest mass and c is the speed of light. Subtracting the rest energy from the total energy yields the relativistic kinetic energy.
Learn more about speed here: brainly.com/question/28224010
#SPJ11
QUESTIONS 1) From the observations of force-acceleration and mass-acceleration, what can you conclude about the validity of Newton's second law of motion, F = ma? Have you verified Newton's second law? What makes one believe that the tensions on the two ends of the string are equal? Is this an instance of Newton's third law of motion? Explain. 4v Previously acceleration was defined as the time rate of change of velocity, a= Δt F Now acceleration is defined as the ratio of force to mass, a = Which is correct? m What is the difference in the two expressions for acceleration?
According to the observations of force-acceleration and mass-acceleration, it can be concluded that Newton's second law of motion, F = ma, is valid.
The experiment verifies that the acceleration of an object is directly proportional to the force applied to it and inversely proportional to its mass. The tensions on both ends of the string are believed to be equal due to Newton's third law of motion, which states that every action has an equal and opposite reaction.
The validity of Newton's second law of motion was verified through the experiment, and it describes the relationship between the force applied to an object, its mass, and its resulting acceleration. The observations of force-acceleration and mass-acceleration indicate that an increase in force or a decrease in mass leads to a corresponding increase in acceleration. The experiment thus confirms the accuracy of F = ma and the proportional relationship between force, mass, and acceleration.
The tensions on the two ends of the string are believed to be equal due to Newton's third law of motion. When a force is applied, an equal and opposite reaction force is produced, which acts in the opposite direction. In the case of the string, the force on one end generates a reactive force on the other end, which balances the tension across the rope. Therefore, the tensions on both ends of the string will be equal.
Lastly, the difference between the two expressions for acceleration lies in their definitions. The previous definition defined acceleration as the time rate of change of velocity, while the recent one defines it as the ratio of force to mass. Both definitions describe the concept of acceleration, but the new definition is more scientific and relates to the broader concept of motion.
To learn more about Newton's second law of motion click brainly.com/question/25545050
#SPJ11
A 1-kg block executes simple harmonic motion with an amplitude A = 15 cm. In 6.8 sec, the block
completes 5-oscillations. Determine the kinetic energy of the oscillator, K =?, at a position where the
potential energy is twice the kinetic energy (U = 2K).
The kinetic energy of the oscillator at a position where the potential energy is twice the kinetic energy is 0.1206 J.
The period of the oscillation is T = 6.8 / 5 = 1.36 seconds.
The angular frequency is ω = 2π / T = 5.23 rad/s.
The potential energy at a position where U = 2K is U = 2 * 0.5 * m * ω² * A² = m * ω² * A².
The kinetic energy at this position is K = m * ω² * A² / 2.
Plugging in the known values, we get K = 1 * 5.23² * (0.15 m)² / 2 = 0.1206 J.
Therefore, the kinetic energy of the oscillator at a position where the potential energy is twice the kinetic energy is 0.1206 J.
Here are the steps in more detail:
We are given that the mass of the block is 1 kg, the amplitude of the oscillation is 15 cm, and the block completes 5 oscillations in 6.8 seconds.We can use these values to calculate the period of the oscillation, T = 6.8 / 5 = 1.36 seconds.We can then use the period to calculate the angular frequency, ω = 2π / T = 5.23 rad/s.We are given that the potential energy at a position where U = 2K is U = 2 * 0.5 * m * ω² * A² = m * ω² * A².We can use this equation to calculate the kinetic energy at this position, K = m * ω² * A² / 2.Plugging in the known values, we get K = 1 * 5.23² * (0.15 m)² / 2 = 0.1206 J.
Therefore, the kinetic energy of the oscillator is 0.1206 J.
To learn more about oscillation :
https://brainly.com/question/12622728
#SPJ11
Two parallel wires are 5.0 cm apart, and each carries a current of 10 A. If the currents are in opposite directions, find the force per unit of length exerted by one of the wires on the other. Are the wires attracted or repelled?
The force per unit length exerted by one wire on the other is 2.0 x 10^-4 N/m. The wires are attracted to each other.
To find the force per unit length exerted by one wire on the other, we can use Ampere's law. According to Ampere's law, the magnetic field produced by a current-carrying wire is directly proportional to the current and inversely proportional to the distance from the wire.
The magnetic field produced by a wire carrying current can be calculated using the formula:
B = (μ₀ * I) / (2π * r)
Where:
B is the magnetic field
μ₀ is the permeability of free space (4π x 10^-7 Tm/A)
I is the current
r is the distance from the wire
In this case, the two wires are parallel and carry currents in opposite directions. The force per unit length (F) between them can be calculated using the formula:
F = (μ₀ * I₁ * I₂) / (2π * d)
Where:
I₁ and I₂ are the currents in the two wires
d is the distance between the wires
Plugging in the values given in the problem, we have:
I₁ = I₂ = 10 A (the currents are the same)
d = 5.0 cm = 0.05 m
Using the formula, we can calculate the force per unit length:
F = (4π x 10^-7 Tm/A * 10 A * 10 A) / (2π * 0.05 m)
= 2 x 10^-4 N/m
The force per unit length exerted by one wire on the other is 2.0 x 10^-4 N/m. Since the currents are in opposite directions, the wires are attracted to each other.
To learn more about force, visit
https://brainly.com/question/18158308
#SPJ11
The magnitude of the orbital angular momentum of an electron in an atom is L=120ħ. How many different values of L, are possible?
The number of different values of orbital angular momentum (L) possible for an electron in an atom is 241.
The orbital angular momentum of an electron is quantized and can only take on specific values given by L = mħ, where m is an integer representing the magnetic quantum number and ħ is the reduced Planck's constant.
In this case, we are given that L = 120ħ. To find the possible values of L, we need to determine the range of values for m that satisfies the equation.
Dividing both sides of the equation by ħ, we have L/ħ = m. Since L is given as 120ħ, we have m = 120.
The possible values of m can range from -120 to +120, inclusive, resulting in 241 different values (-120, -119, ..., 0, ..., 119, 120).
Therefore, there are 241 different values of orbital angular momentum (L) possible for the given magnitude of 120ħ.
learn more about orbital angular momentum here:
https://brainly.com/question/31626716
#SPJ11
cylinder from Heat Transfer) 2. Find the overall resistance per metre length for the following: α i =1500 W/m 2 K, α 0 =12X0 W/m 2 K, and α i =1500 W/m 2 K,α 0 =2YoW/m 2 K. Use 2in. standard type M copper tube dimensions, λ copper =399 W/mK. Compare the results.
The overall resistance per meter length for the given conditions can be calculated as follows:
For the first case (αi = 1500 W/m²K, αo = 120 W/m²K):
Overall resistance, R1 = (1 / αi) + (t / λ) + (1 / αo)
Where t is the thickness of the copper tube.
For the second case (αi = 1500 W/m²K, αo = 20 W/m²K):
Overall resistance, R2 = (1 / αi) + (t / λ) + (1 / αo)
To calculate the overall resistance per meter length, we consider the resistance to heat transfer at the inside surface of the tube, the resistance through the tube wall, and the resistance at the outside surface of the tube.
In both cases, we use the given values of αi (inside surface heat transfer coefficient), αo (outside surface heat transfer coefficient), and λ (thermal conductivity of copper) to calculate the individual resistances. The thickness of the copper tube, denoted as t, is also considered.
The overall resistance is obtained by summing up the individual resistances using the appropriate formula for each case.
By comparing the overall resistance per meter length for the two cases, we can assess the impact of the different values of αo. The comparison will provide insight into how the outside surface heat transfer coefficient affects the overall heat transfer characteristics of the system.
To learn more about resistance ,visit
brainly.com/question/17563681
#SPJ11
. 5. Which of the following is/are correct about a sound wave? A. B. C. Infrasound is visible to the eye. Sound waves can travel in a conductor. Sound wave travels in a vacuum at 3 x 108 m/s.
Among the options provided, the correct statement is "Sound waves can travel in a conductor." Infrasound is not visible to the eye, and sound waves do not travel in a vacuum at 3 x 108 m/s.
A. Infrasound is not visible to the eye. Infrasound refers to sound waves with frequencies below the range of human hearing, typically below 20 Hz. Since our eyes are designed to detect visible light, they cannot directly perceive infrasound waves.
B. Sound waves can travel in a conductor. Yes, this statement is correct. Sound waves are mechanical waves that propagate through a medium by causing particles in the medium to vibrate. While sound waves travel most efficiently through solids, they can also travel through liquids and gases, including conductors like metals.
C. Sound waves do not travel in a vacuum at 3 x 108 m/s. Sound waves require a medium to propagate, and they cannot travel through a vacuum as there are no particles to transmit the mechanical vibrations. In a vacuum, electromagnetic waves, such as light, can travel at a speed of approximately 3 x 108 m/s, but not sound waves.
Learn more about Infrasound here:
https://brainly.com/question/17025745
#SPJ11
An ideal step-down transformer has a primary coil of 710 turns and a secondary coil of 30 turns. Its primary coil is plugged into an outlet with 12 V(AC), from which it draws an rms current of 0.3 A. What is the voltage and rms current in the secondary coil?
- The voltage in the secondary coil is approximately 0.509 V (rms).
- The rms current in the secondary coil is approximately 7 A.
In an ideal step-down transformer, the voltage ratio is inversely proportional to the turns ratio. We can use this relationship to determine the voltage and current in the secondary coil.
Primary coil turns (Np) = 710
Secondary coil turns (Ns) = 30
Primary voltage (Vp) = 12 V (rms)
Primary current (Ip) = 0.3 A (rms)
Using the turns ratio formula:
Voltage ratio (Vp/Vs) = (Np/Ns)
Vs = Vp * (Ns/Np)
Vs = 12 V * (30/710)
Vs ≈ 0.509 V (rms)
Therefore, the voltage in the secondary coil is approximately 0.509 V (rms).
To find the current in the secondary coil, we can use the current ratio formula:
Current ratio (Ip/Is) = (Ns/Np)
Is = Ip * (Np/Ns)
Is = 0.3 A * (710/30)
Is ≈ 7 A (rms)
Therefore, the rms current in the secondary coil is approximately 7 A.
Learn more about step-down transformers at https://brainly.com/question/3767027
#SPJ11
A 1.60-m-long steel piano wire has a diameter of 0.20 cm. How great is the tension in the wire if it stretches 0.25 cm when tightened? Approximately what tension force would break it? The tensile strength of steel is 1.0×10 ^9
N/m ^2
The tension in the wire is about 50.9 N. The tensile strength of the wire is about 1000 N, so the wire would break if the tension were increased to about 1000 N.
The tension in the wire can be calculated using the following formula:
T = F / A
where
* T is the tension in the wire (in N)
* F is the force applied to the wire (in N)
* A is the cross-sectional area of the wire (in m²)
The cross-sectional area of the wire can be calculated using the following formula:
A = πr²
where
* r is the radius of the wire (in m)
In this case, the force applied to the wire is the weight of the wire, which is:
F = mg
where
* m is the mass of the wire (in kg)
* g is the acceleration due to gravity (in m/s²)
The mass of the wire can be calculated using the following formula:
m = ρL
where
* ρ is the density of the wire (in kg/m³)
* L is the length of the wire (in m)
The density of steel is about 7850 kg/m³. The length of the wire is 1.60 m. The radius of the wire is 0.01 m.
Substituting these values into the equations above, we get:
T = F / A = mg / A = ρL / A = (7850 kg/m³)(1.60 m) / π(0.01 m)² = 50.9 N
The tensile strength of steel is about 1000 N. This means that the wire would break if the tension were increased to about 1000 N.
Learn more about tension force here; brainly.com/question/30470948
#SPJ11
If given a 2-D conductor at zero Kelvin temperature, then the electron density will be expressed as:
If given a 2-D conductor at zero Kelvin temperature, then the electron density will be expressed as:
n = (2 / h²) * m_eff * E_F
Where n is the electron density in the conductor, h is the Planck's constant, m_eff is the effective mass of the electron in the conductor, and E_F is the Fermi energy of the conductor.
The Fermi energy of the conductor is a measure of the maximum energy level occupied by the electrons in the conductor at absolute zero temperature.
To learn more about conductor, refer below:
https://brainly.com/question/14405035
#SPJ11
You're in an airplane flying 860 km/hkm/h (240 m/sm/s) horizontally when an engine falls off. Neglecting air resistance, assume it takes 34 s for the engine to hit the ground.
Find the height of airplane.
Find the horizontal distance that the engine moves during its fall.
If the airplane somehow continues to fly as if nothing had happened, what is the distance between the engine and the airplane at the moment the engine hits the ground?
The height of the airplane can be calculated by multiplying the time it takes for the engine to hit the ground by the vertical velocity of the engine.
The horizontal distance traveled by the engine during its fall can be determined by multiplying the horizontal velocity of the airplane by the time it takes for the engine to hit the ground.
To find the height of the airplane, we can use the equation h = v*t, where h represents the height, v is the vertical velocity, and t is the time. The vertical velocity can be determined by converting the horizontal velocity of the airplane to meters per second. Since the airplane is flying at 860 km/h, the vertical velocity is 860 km/h * (1000 m/km) / (3600 s/h) = 238.89 m/s. Multiplying the vertical velocity by the time it takes for the engine to hit the ground (34 s) gives us the height of the airplane: h = 238.89 m/s * 34 s = 8122.26 m.
The horizontal distance traveled by the engine during its fall can be calculated using the equation d = v*t, where d represents the distance and v is the horizontal velocity of the airplane. Given that the airplane is flying at a speed of 860 km/h, the horizontal velocity is 860 km/h * (1000 m/km) / (3600 s/h) = 238.89 m/s. Multiplying the horizontal velocity by the time it takes for the engine to hit the ground (34 s) gives us the horizontal distance traveled by the engine: d = 238.89 m/s * 34 s = 8115.26 m.
To determine the distance between the engine and the airplane at the moment the engine hits the ground, we can use the Pythagorean theorem. The distance between the engine and the airplane forms a right triangle, with the horizontal distance (8115.26 m) as one side and the height of the airplane (8122.26 m) as the other side. Using the theorem, we can calculate the distance as follows: distance = √(8115.26^2 + 8122.26^2) = 11488.91 m.
Therefore, the height of the airplane is 8122.26 m, the horizontal distance traveled by the engine is 8115.26 m, and the distance between the engine and the airplane at the moment the engine hits the ground is 11488.91 m.
Learn more about speed here:
brainly.com/question/17661499
#SPJ11
The figure below shows three charged particles at the corners of an equilateral triangle. Particle A has a charge of 1.30 µC; B has a charge of 5.60 µC; and C has a charge of −5.06 µC. Each side of the triangle is 0.500 m long.
What are the magnitude and direction of the net electric force on A? (Enter the magnitude in N and the direction in degrees below the +x-axis.)
Find magnitude in N
Find direction ° below the +x-axis
The magnitude and direction of the net electric force on particle A with the given charge, distances, and angles. The force on particle.
A due to the charges of particles B and C can be computed using the Coulomb force formula:
[tex]F_AB = k q_A q_B /r_AB^2[/tex]
where, k = 9.0 × 10^9 N · m²/C² is Coulomb's constant,
[tex]q_A = 1.30 µC, q_B = 5.[/tex]
60 µC are the charges of the particles in coulombs, and[tex]r_AB[/tex] = 0.5 m is the distance between A and B particles.
We can also find the force between A and C and between B and C particles. Using the Coulomb force formula:
[tex]F_AC = k q_A q_C /r_AC^2[/tex]
[tex]F_BC = k q_B q_C /r_BC^2[/tex]
where, r_AC = r_BC = 0.5 m and q_C = -5.06 µC are the distances and charges, respectively.
Each force [tex](F_AB, F_AC, F_BC)[/tex]has a direction and a magnitude.
To calculate the net force on A, we need to break each force into x and y components and add up all the components. Then we can calculate the magnitude and direction of the net force.
To know more about particle visit:
https://brainly.com/question/13874021
#SPJ11
An object is located 3cm in front of a concave mirror whose
radius of curvature is 12cm. Find (a) the focal length of the
mirror and (b) position of the image. Describe the image.
The focal length (f) of a concave mirror is the distance between the mirror's center of curvature (C) and its focal point (F). The center of curvature is the center of the sphere from which the mirror is a part, and the focal point is the point at which parallel rays of light, when reflected by the mirror, converge or appear to converge.
To find the focal length of the mirror and the position of the image and to describe the image. The formula for focal length of the mirror is: 1/f = 1/v + 1/u where f is the focal length of the mirror, u is the distance of the object from the mirror, v is the distance of the image from the mirror.
(a) Calculation of focal length: Using the formula of the mirror, we get1/f = 1/v + 1/u = (u + v) / uv...[1]Also given that radius of curvature of mirror, R = - 12 cm where the negative sign indicates that it is a concave mirror. Using the formula of radius of curvature, we get f = R/2 = - 12/2 = - 6 cm (as f is negative for concave mirror)...[2]By substituting the values from equation 1 and 2, we get(u + v) / uv = 1/-6=> -6 (u + v) = uv=> - 6u - 6v = uv=> u (v + 6) = - 6v=> u = 6v / v + 6On substituting the value of u in equation 1, we get1/f = v + 6 / 6v => 6v + 36 = fv=> v = 6f / f + 6On substituting the value of v in equation 2, we getf = - 3 cmTherefore, the focal length of the mirror is -3 cm.
(b) Calculation of image position: By using the formula of magnification, we getmagnification = height of the image / height of the object where we can write height of the image / height of the object = - v / u = - (f / u + f)Also given that the object is located 3 cm in front of the mirror where u = -3 cm and f = - 3 cm Substituting the values in the above formula, we get magnification = - 1/2. It means the size of the image is half of the object. Therefore, the image is real, inverted and located at a distance of 6 cm behind the mirror.
For similar problems on ray optics visit:
https://brainly.com/question/13088184
#SPJ11
Which of the following remain(s) constant for a projectile: it's horizontal velocity component, v, it's vertical velocity component, Vv, or it's vertical acceleration, g? Select one: O a. g and VH O b. g, V and Vv O c..g and v O d. Vv
Out of the given options, the term that remains constant for a projectile is c. g and v.
Over the course of the projectile's motion, the acceleration caused by gravity is constant. This indicates that the vertical acceleration is unchanged. As long as no external forces are exerted on the projectile horizontally, the horizontal velocity component is constant. This is due to the absence of any horizontal acceleration.
Due to the acceleration of gravity, the vertical component of the projectile's velocity varies throughout its motion. It grows as it moves upward, hits zero at its highest point, and then starts to diminish as it moves lower. The gravity-related acceleration (g) and the component of horizontal velocity (v) are thus the only constants for a projectile.
Read more about projectile on:
https://brainly.com/question/30448534
#SPJ4
You place a crate of mass 44.7 kg on a frictionless 2.38-meter-long incline. You release the crate from rest, and it begins to slide down, eventually reaching the bottom 0.97 seconds after you released it. What is the angle of the incline?
The angle of the incline is approximately 24.2 degrees.
To calculate the angle of the incline, we can use the equation of motion for an object sliding down an inclined plane. The equation is given by:
d = (1/2) * g * t^2 * sin(2θ)
where d is the length of the incline, g is the acceleration due to gravity (approximately 9.8 m/s^2), t is the time taken to slide down the incline, and θ is the angle of the incline.
In this case, the length of the incline (d) is given as 2.38 meters, the time taken (t) is 0.97 seconds, and we need to solve for θ. Rearranging the equation and substituting the known values, we can solve for θ:
θ = (1/2) * arcsin((2 * d) / (g * t^2))
Plugging in the values, we get:
θ ≈ (1/2) * arcsin((2 * 2.38) / (9.8 * 0.97^2))
θ ≈ 24.2 degrees
To learn more about motion, click here:
brainly.com/question/12640444
#SPJ11
calculate the rotational inertia of a meter stick, with mass 0.56 kg, about an axis perpendicular to the stick and located at the 20 cm mark. (treat the stick as a thin rod.) (a) 1.1 kgm2 (b) 3.2 kgm2 (c) 4.2 kgm2 (d) 0.097 kgm2
Rounding to two decimal places, the rotational inertia of the meter stick is approximately 0.097 kgm^2. Therefore, the correct answer is (d) 0.097 kgm^2.
To calculate the rotational inertia of the meter stick, we need to use the formula for the rotational inertia of a thin rod. The formula is given by I = (1/3) * m * L^2, where I is the rotational inertia, m is the mass of the rod, and L is the length of the rod.
In this case, the mass of the meter stick is given as 0.56 kg, and the length of the stick is 1 meter. Since the axis of rotation is perpendicular to the stick and located at the 20 cm mark, we need to consider the rotational inertia of two parts: one part from the 0 cm mark to the 20 cm mark, and another part from the 20 cm mark to the 100 cm mark.
For the first part, the length is 0.2 meters and the mass is 0.2 * 0.56 = 0.112 kg. Plugging these values into the formula, we get:
I1 = (1/3) * 0.112 * (0.2)^2 = 0.00149 kgm^2.
For the second part, the length is 0.8 meters and the mass is 0.8 * 0.56 = 0.448 kg. Plugging these values into the formula, we get:
I2 = (1/3) * 0.448 * (0.8)^2 = 0.09504 kgm^2.
Finally, we add the rotational inertias of both parts to get the total rotational inertia:
I_total = I1 + I2 = 0.00149 + 0.09504 = 0.09653 kgm^2.
Rounding to two decimal places, the rotational inertia of the meter stick is approximately 0.097 kgm^2. Therefore, the correct answer is (d) 0.097 kgm^2.
To know more about length visit:
https://brainly.com/question/32060888
#SPJ11
A proton moving at 7.00 106 m/s through a magnetic field of magnitude 1.80 T experiences a magnetic force of magnitude 8.00 10-13 N. What is the angle between the proton's velocity and the field? (Enter both possible answers from smallest to largest. Enter only positive values between 0 and 360.)smaller value °
larger value °
The angle between the proton's speed and the magnetic field is roughly 0.205 degrees.
Magnetic field calculation.To decide angle between the proton's speed and the magnetic field, able to utilize the equation for the attractive constrain on a moving charged molecule:
F = q * v * B * sin(theta)
Where:
F is the greatness of the magnetic force (given as 8.00 * 10³N)
q is the charge of the proton (which is the rudimentary charge, e = 1.60 * 10-³ C)
v is the speed of the proton (given as 7.00 * 10-³ m/s)
B is the greatness of the attractive field (given as 1.80 T)
theta is the point between the velocity and the field (the esteem we have to be discover)
Improving the equation, ready to unravel for theta:
sin(theta) = F / (q * v * B)
Presently, substituting the given values:
sin(theta) = (8.00 * 10-³ N) / ((1.60 * 10^-³C) * (7.00 * 10-³ m/s) * (1.80 T))
Calculating the esteem:
sin(theta) ≈ 3.571428571428571 * 10^-²
Now, to discover the point theta, ready to take the reverse sine (sin of the calculated esteem:
theta = 1/sin (3.571428571428571 * 10-²)
Employing a calculator, the esteem of theta is around 0.205 degrees.
So, the littler esteem of the angle between the proton's speed and the attractive field is roughly 0.205 degrees.
Learn more about magnetic field below.
https://brainly.com/question/26257705
#SPJ4
If c = - 4x + 3y and t = 3x 2y, find the magnitude and direction (angle with respect to +x axis) of the following vectors
a) q = c - 3t
b) p = 3c 3t/2
(a)The magnitude of vector q is approximately 13.34 and its direction is approximately 12.99° with respect to the +x axis. (b)The magnitude of vector p is approximately 11.87 and its direction is approximately -75.96° .
Let's calculate the magnitude and direction of the given vectors:
a) q = c - 3t
Given:
c = -4x + 3y
t = 3x + 2y
Substituting the values into the expression for q:
q = (-4x + 3y) - 3(3x + 2y)
q = -4x + 3y - 9x - 6y
q = -13x - 3y
To find the magnitude of vector q, we use the formula:
|q| = √(qx^2 + qy^2)
Plugging in the values:
|q| = √((-13)^2 + (-3)^2)
|q| = √(169 + 9)
|q| = √178
|q| ≈ 13.34
To find the direction of vector q (angle with respect to the +x axis), we use the formula:
θ = tan^(-1)(qy / qx)
Plugging in the values:
θ = tan^(-1)(-3 / -13)
θ ≈ tan^(-1)(0.23)
θ ≈ 12.99°
Therefore, the magnitude of vector q is approximately 13.34 and its direction is approximately 12.99° with respect to the +x axis.
b) p = 3c + (3/2)t
Given:
c = -4x + 3y
t = 3x + 2y
Substituting the values into the expression for p:
p = 3(-4x + 3y) + (3/2)(3x + 2y)
p = -12x + 9y + (9/2)x + 3y
p = (-12 + 9/2)x + (9 + 3)y
p = (-15/2)x + 12y
To find the magnitude of vector p, we use the formula:
|p| = √(px^2 + py^2)
Plugging in the values:
|p| = √((-15/2)^2 + 12^2)
|p| = √(225/4 + 144)
|p| = √(561/4)
|p| ≈ 11.87
To find the direction of vector p (angle with respect to the +x axis), we use the formula:
θ = tan^(-1)(py / px)
Plugging in the values:
θ = tan^(-1)(12 / (-15/2))
θ ≈ tan^(-1)(-16/5)
θ ≈ -75.96°
To learn more about vector, click here:
https://brainly.com/question/14447709
#SPJ11
Question 2. [6 marks] A system asshown in the figure is used to measure accurately the pressure changes when pressure is increased by AP inside the water pipe. When the height difference reaches Ah = 70 mm, what is the change in pipe pressure? Water Pipe Glycerin, SG= 1.26 D= 30 mm Ah d=3 mm
The change in pipe pressure when the height difference reaches Ah = 70 mm is 17.3 kPa.
To calculate the change in the pipe pressure when the height difference reaches Ah=70mm, we use Bernoulli's theorem, the pressure difference between the two points is given by:
ΔP = (ρ/2)(v₁²-v₂²)
Pressure difference (ΔP) is given by:
ΔP = ρgh
where ρ is the density of the fluid, g is the gravitational acceleration, and h is the height difference.
The velocity of the fluid at each point is determined using the equation of continuity.
A₁v₁ = A₂v₂
The velocity of the fluid at point 1 is given by:
v₁ = Q/πd²/4
where Q is the flow rate.
The velocity of the fluid at point 2 is given by:
v₂ = Q/πD²/4
The pressure difference is given by:
ΔP = ρgh
= (ρ/2)(v₁²-v₂²)
Substitute v₁ = Q/πd²/4 and v₂ = Q/πD²/4
ΔP = (ρ/2)(Q²/π²d⁴ - Q²/π²D⁴)
Simplify the equation,
ΔP = (ρQ²/8π²d⁴)(D⁴-d⁴)
ΔP = (1/8)(ρQ²/πd⁴)(D⁴-d⁴)
Since the flow rate Q is the same at both points, it can be cancelled out.
ΔP = (1/8)(ρ/πd⁴)(D⁴-d⁴)
The change in the pipe pressure when the height difference reaches Ah=70mm is given by:
Δh = Ah - h₂
Where, h₂ = d/2
The height difference is converted to meters.
Δh = 70/1000 - 30/1000 = 0.04 m
Substitute the given values in the above equation to get the change in pipe pressure:
ΔP = (1/8)(ρ/πd⁴)(D⁴-d⁴) * Δh
ΔP = (1/8)(1.26/π(30/1000)⁴)(3/1000)⁴) * 0.04
ΔP = 17.3 kPa
Learn more about change in pipe pressure: https://brainly.com/question/15079200
#SPJ11
An object is 2m away from a convex mirror in a store, its image
is 1 m behind the mirror. What is the focal length of the
mirror?
The focal length of the convex mirror is -2 m. The negative sign indicates that the mirror has a diverging effect, as is characteristic of convex mirrors.
To determine the focal length of a convex mirror, we can use the mirror equation:
1/f = 1/d_o + 1/d_i
Where f is the focal length, d_o is the object distance (distance of the object from the mirror), and d_i is the image distance (distance of the image from the mirror).
In this case, the object distance (d_o) is given as 2 m, and the image distance (d_i) is given as -1 m (since the image is formed behind the mirror, the distance is negative).
Substituting the values into the mirror equation:
1/f = 1/2 + 1/-1
Simplifying the equation:
1/f = 1/2 - 1/1
1/f = -1/2
To find the value of f, we can take the reciprocal of both sides of the equation:
f = -2/1
f = -2 m
Therefore, the focal length of the convex mirror is -2 m. The negative sign indicates that the mirror has a diverging effect, as is characteristic of convex mirrors.
Learn more about a convex mirror:
https://brainly.com/question/32811695
#SPJ11