a. Theory of equipartition of energy states that each degree of freedom of a molecule has an average energy of kT/2. Therefore, the molar specific heat of an ideal gas can be expressed as Cv = (f/2)R and Cp = [(f/2) + 1]R,specific heat at constant pressure.
For a diatomic gas, the molecule has five degrees of freedom: three translational and two rotational. Therefore, Cv = (5/2)R = 20.8 J mol-1 K-1 and Cp = (7/2)R = 29.1 J mol-1 K-1.
b. During the isochoric heating process, the volume of the gas remains constant, and the pressure increases from 0.75 x 105 Pa to 1.01 x 105 Pa. Using the ideal gas law, the temperature change can be found: ΔT = ΔQ/Cv = (ΔU/m)Cv = (3/2)R(ΔT/m). Substituting the values, we get ΔT = 35.2 K. Therefore, the thermal energy added to the gas is Q = CvΔT = 727 J.
c. The p-V diagram for the isochoric heating process is shown below. The work done by the gas during the constant-pressure expansion process is given by W = nRΔTln(Vf/Vi), where Vf is the final volume of the gas, and Vi is the initial volume of the gas. Using the ideal gas law, the final volume can be found: Vf = nRTf/Pf. Substituting the values, we get Vf = 0.0137 m³. Therefore, the total work done by the gas is W = nRΔTln(Vf/Vi) + P(Vf - Vi) = 294 J + 1538 J = 1832 J.
d. During the second heating process, the gas expands at constant pressure to a final temperature of 200 °C. The volume change can be found using the ideal gas law: ΔV = nRΔT/P = 3.9 x 10-³ m³. Therefore, the lid of the piston moves a distance of Δx = ΔV/h = 3.9 x 10-³ m. Answer: The distance moved by the lid of the piston is 3.9 x 10-³ m during the second heating process.
To know more about equipartition visit:
https://brainly.com/question/30907512
#SPJ11
A diffuser operates at sea-level at M 0 =1.5 with π d,max =0.98 and where η r ={ 1 for M 0 ≤11−0.075(M 0 −1) 1.35 for 1
b. p t0
C. p t2
d. T t2
e. T t2,s
(the value of T t2 for an isentropic compressor) f. η d = T t2 −T 0T t2,s −T 0 [ Ans :η d =0.954] g. Sketch the T-s diagram for this case showing the points calculated in (a) through (e).
The diffuser operates at sea-level with a Mach number (M0) of 1.5, achieving a maximum pressure recovery (πd,max) of 0.98. The overall diffuser efficiency (ηd) is calculated to be 0.954.
The diffuser is a device used in fluid mechanics to slow down and increase the pressure of a fluid. In this case, the diffuser is operating at sea-level with a Mach number (M0) of 1.5, which indicates that the flow velocity is supersonic. The maximum pressure recovery (πd,max) is given as 0.98, meaning that the diffuser can recover up to 98% of the static pressure.
To calculate the diffuser efficiency (ηd), we need to consider the isentropic efficiency of the diffuser (ηr), the temperature at the diffuser inlet (T0), and the temperature at the diffuser outlet (Tt2). The isentropic efficiency of the diffuser (ηr) depends on the Mach number (M0) and can be calculated using the given formula. In this case, ηr is given as 1 for M0 ≤ 1, and 1.35 for 1 < M0 < 11 - 0.075(M0 - 1).
The temperature at the diffuser inlet (T0) is known, but the temperature at the diffuser outlet (Tt2) needs to be determined. The value of Tt2 for an isentropic compressor is given as 1. Hence, we need to calculate Tt2 using the given formula. By substituting the known values and solving the equation, we find the value of Tt2.
Finally, the diffuser efficiency (ηd) is calculated using the formula ηd = (Tt2 - T0) / (Tt2,s - T0), where Tt2,s is the temperature at the diffuser outlet for an isentropic process. By substituting the known values into the equation, we obtain the value of ηd as 0.954.
Learn more about Diffuser
brainly.com/question/14852229
#SPJ11
Please describe the theory of operation of DC motor and current
measurement method based on Hall Effect in details.
The operation of a DC motor relies on the interaction between a magnetic field and an electric current. This interaction produces a mechanical force that causes the motor to rotate.The basic structure of a DC motor is comprised of a stator and rotor.
The stator consists of a fixed magnetic field, typically produced by permanent magnets. The rotor is the rotating part of the motor and is connected to an output shaft. The rotor contains the conductors that carry the electric current and is surrounded by a magnetic field produced by the stator.
The interaction between the magnetic fields causes a force on the rotor conductors, producing a rotational torque on the output shaft. The direction of rotation can be controlled by changing the polarity of the magnetic field or the direction of the current.
To know more about operation visit:
https://brainly.com/question/30581198
#SPJ11
A box with a mass of 17 kg is suspended from a spring that is stretched 150 mm. If the box is displaced 100 mm downward from its equilibrium position and given a downward velocity of 700 mm/s, determine the equation which describes the motion. What is the phase angle and amplitude of vibration? Assume that positive displacement is downward.
The box is in simple harmonic motion with the following parameters. Since the box is displaced from equilibrium and is given an initial velocity, it vibrates with amplitude and has a phase angle.
In simple harmonic motion,
x = A sin (ωt + φ).
x = A sin (ωt + φ)
can be used to describe the equation of motion for the given problem.For this equation of motion, the amplitude (A) and phase angle (φ) must be calculated using the given conditions.ω, the angular frequency, can be found using the formula for a mass-spring system's angular frequency:
ω = sqrt(k/m)
where k is the spring constant and m is the mass of the box .
In this case, the box is displaced 100 mm downward from its equilibrium position, thus the amplitude of vibration is A = 100 mm. The phase angle can be determined using the following equation:
φ = arctan(-v0/ωx)
where v0 is the initial velocity (700 mm/s), ω is the angular frequency (9.05 rad/s), and x is the amplitude (mm).
φ=arctan(-700/(9.05*100))
φ =-43.33 degrees.
The equation of motion for the given problem is
x = 100 sin (9.05t - 43.33).
The amplitude of vibration is 100 mm and the phase angle is -43.33 degrees.
To know more about equation visit:
https://brainly.com/question/29538993
#SPJ11
For corrosion to occur, there must be an anodic and cathodic reaction, oxygen must be available, and there must be both an electronically and fonically conductive path True O False
The given statement, "For corrosion to occur, there must be an anodic and cathodic reaction, oxygen must be available, and there must be both an electronically and fonically conductive path" is true.
The occurrence of corrosion is reliant on three necessary factors that must be present simultaneously. These three factors are:Anode and cathode reaction: When a metal comes into touch with an electrolyte, an oxidation reaction occurs at the anode, and an opposite reaction of reduction occurs at the cathode. The reaction at the anode causes the metal to dissolve into the electrolyte, and the reaction at the cathode protects the metal from corrosion.
Oxygen: For the cathodic reaction to take place, oxygen must be present. If there is no oxygen available, the reduction reaction at the cathode will not happen, and hence, no cathodic protection against corrosion.Electronically and Fonically Conductive Path: To make a closed circuit, the anode and cathode should be electrically connected. A connection can occur when the metal comes into touch with a different metal or an electrolyte that conducts electricity.
To know more about corrosion visit:
https://brainly.com/question/31313074
#SPJ11
The flow just upstream of a normal shock wave is given by p₁ = 1 atm, T₁ = 288 K, and M₁ = 2.6. Calculate the following properties just downstream of the shock: p2, T2, P2, M2, Po.2, To.2, and the change in entropy across the shock.
The normal shock wave is a type of shock wave that occurs at supersonic speeds. It's a powerful shock wave that develops when a supersonic gas stream encounters an obstacle and slows down to subsonic speeds. The following are the downstream properties of a normal shock wave:Calculation of downstream properties:
Given,Upstream properties: p₁ = 1 atm, T₁ = 288 K, M₁ = 2.6Downstream properties: p2, T2, P2, M2, Po.2, To.2, and change in entropy across the shock.Solution:First, we have to calculate the downstream Mach number M2 using the upstream Mach number M1 and the relationship between the Mach number before and after the shock:
[tex]$$\frac{T_{2}}{T_{1}} = \frac{1}{2}\left[\left(\gamma - 1\right)M_{1}^{2} + 2\right]$$$$M_{2}^{2} = \frac{1}{\gamma M_{1}^{-2} + \frac{\gamma - 1}{2}}$$$$\therefore M_{2}^{2} = \frac{1}{\frac{1}{M_{1}^{2}} + \frac{\gamma - 1}{2}}$$$$\therefore M_{2} = 0.469$$[/tex]
Now, we can calculate the other downstream properties using the following equations:
[tex]$$\frac{P_{2}}{P_{1}} = \frac{\left(\frac{2\gamma}{\gamma + 1}M_{1}^{2} - \frac{\gamma - 1}{\gamma + 1}\right)}{\left(\gamma + 1\right)}$$$$\frac{T_{2}}{T_{1}} = \frac{\left(\frac{2\gamma}{\gamma + 1}M_{1}^{2} - \frac{\gamma - 1}{\gamma + 1}\right)^{2}}{\gamma\left(\frac{2\gamma}{\gamma + 1}M_{1}^{2} - \frac{\gamma - 1}{\gamma + 1}\right)^{2} - \left(\gamma - 1\right)}$$$$P_{o.2} = P_{1}\left[\frac{2\gamma}{\gamma + 1}M_{1}^{2} - \frac{\gamma - 1}{\gamma + 1}\right]^{(\gamma)/( \gamma - 1)}$$$$T_{o.2} = T_[/tex]
where R is the gas constant and [tex]$C_{p}$[/tex] is the specific heat at constant pressure.We know that,
γ = 1.4, R = 287 J/kg-K, and Cp = 1.005 kJ/kg-K
Substituting the values, we get,Downstream Mach number,M2 = 0.469Downstream Pressure,P2 = 3.13 atmDownstream Temperature,T2 = 654 KDownstream Density,ρ2 = 0.354 kg/m³Stagnation Pressure,Po.2 = 4.12 atmStagnation Temperature,To.2 = 582 KChange in entropy across the shock,Δs = 1.7 J/kg-KHence, the required downstream properties of the normal shock wave are P2 = 3.13 atm, T2 = 654 K, P2 = 0.354 kg/m³, Po.2 = 4.12 atm, To.2 = 582 K, and Δs = 1.7 J/kg-K.
To know more about downstream visit :
https://brainly.com/question/14158346
#SPJ11
The interior walls as well the ceiling and the floor of a room are all at T = 12 deg C. The room air is continuously circulated, providing an average convection coefficient of 6.3 W m-2 K-1 at an average temperature of T₁ = 21 deg C. If the room measures 5 m X 4 m X 3 m, estimate the rate at which the air is cooling the room (a negative answer will imply the air is heating the room). Enter your answer using two significant digits in kW.
The rate at which air cools the room has to be calculated. The dimensions of the room are 5 m × 4 m × 3 m. The air in the room is continuously circulated, coefficient of 6.3 W m−2 K−1 and an average temperature of T1 = 21 °C.Therefore, the rate at which air cools the room is approximately 0.12 kW.
The temperature of the ceiling, interior walls, and floor of the room are all T = 12 °C. The rate at which the air cools the room can be determined using the heat balance equation given below:Q = UA(T1 − T2)whereQ = heat transfer rateU = overall heat transfer coefficientA = surface area (excluding floor area)T1 = room air temperatureT2 = room surface temperatureWe can assume that the room has a shape of a rectangular parallelepiped, and calculate its surface area as follows:SA = (5 × 4) + (5 × 3) + (4 × 3) = 41 m²
The convection coefficient h is given as 6.3 W/m²K. The thickness of the wall Δx is 0.1 m. The thermal conductivity of the wall k is 0.7 W/mK.U = 2/6.3 + 0.1/0.7 + 2/6.3U = 0.3218 W/m²KUsing the heat balance equation, the rate of heat transfer is given asQ = UA(T1 − T2)Q = 0.3218 × 41 × (21 − 12)Q = 117.6 WThe rate of heat transfer in kW can be determined by dividing the result by 1000W:117.6/1000 = 0.118 kW
To know more about approximately visit:
https://brainly.com/question/31695967
#SPJ11
A flat-panel domestic heater 1 m tall x 2 m long is used to maintain a room at 20 °C. An electrical element keeps the surfaces of the radiator at 65 °C. Approximating the heater as a vertical flat plate, calculate the heat transferred to the room by natural convection from both surfaces of the heater (front and back). Assuming that the surface of the heater is painted white, calculate the heat transferred from the radiator to the surrounding surfaces by radiation. Note: The emissivity value of white paint for longwave radiation is approximately 0.8.
The heat transferred from the radiator to the surrounding surfaces by radiation is 321.56 W.
Given that the flat-panel domestic heater is 1 m tall and 2 m long. The heater maintains the room temperature at 20°C. The electrical element keeps the surface temperature of the radiator at 65°C. The heater is approximated as a vertical flat plate. The heat transferred to the room by natural convection from both surfaces of the heater (front and back) can be calculated using the following formula;
Q = h × A × (ΔT)
Q = heat transferred
h = heat transfer coefficient
A = surface are (front and back)
ΔT = temperature difference = 65 - 20 = 45°C
For natural convection, the value of h is given by;
h = k × (ΔT)^1/4
Where k = 0.15 W/m2K
For the front side;
A = 1 × 2 = 2 m2
h = 0.15 × (45)^1/4 = 3.83 W/m2K
Q = h × A × (ΔT)Q = 3.83 × 2 × 45 = 344.7 W
For the back side, the temperature difference will be the same but the surface area will change.
Area of back side = 1 × 2 = 2 m2
h = 0.15 × (45)^1/4 = 3.83 W/m2K
Q = h × A × (ΔT)Q = 3.83 × 2 × 45 = 344.7 W
The total heat transferred by natural convection from the front and back surface is;
Qtotal = 344.7 + 344.7 = 689.4 W
The heat transferred from the radiator to the surrounding surfaces by radiation can be calculated using the following formula;
Q = σ × A × ε × (ΔT)^4
Where σ = 5.67 × 10-8 W/m2K
4A = 1 × 2 = 2 m2
ΔT = (65 + 273) - (20 + 273) = 45°C
Emissivity ε = 0.8Q = 5.67 × 10-8 × 2 × 0.8 × (45)^4Q = 321.56 W
Therefore, the heat transferred from the radiator to the surrounding surfaces by radiation is 321.56 W.
Learn more about natural convection visit:
brainly.com/question/29451753
#SPJ11
A pipe with an inner diameter of 13.5 inches and a wall thickness of 0.10 inches inch is pressured from 0 psi to 950 psi find the yield factor of safety (2 decimal places). Just use the tangential stress for the analysis.
Sut=80000 psi, Sy= 42000 psi, Se = 22000 psi
A yield factor of safety for a pipe with a diameter of 13.5 inches and a wall thickness of 0.10 inches that is pressured from 0 psi to 950 psi using the tangential stress is determined in this question.
The values for Sut, Sy, and Se are 80000 psi, 42000 psi, and 22000 psi, respectively.
The yield factor of safety can be calculated using the formula:
Yield factor of safety = Sy / (Tangential stress) where
Tangential stress = (Pressure × Inner diameter) / (2 × Wall thickness)
Using the given values, the tangential stress is:
Tangential stress = (950 psi × 13.5 inches) / (2 × 0.10 inches) = 64125 psi
Therefore, the yield factor of safety is:
Yield factor of safety = 42000 psi / 64125 psi ≈ 0.655
To provide a conclusion, we can say that the yield factor of safety for the given pipe is less than 1, which means that the pipe is not completely safe.
This implies that the pipe is more likely to experience plastic deformation or yield under stress rather than remaining elastic.
Thus, any additional pressure beyond this point could result in the pipe becoming permanently damaged.
To know more about yield factor visit:
brainly.com/question/31857073
#SPJ11
Airbus 350 Twinjet operates with two Trent 1000 jet engines that work on an ideal cycle. At 1.8km, ambient air flowing at 55 m/s will enter the 1.25m radius inlet of the jet engine. The pressure ratio is 44:1 and hot gasses leave the combustor at 1800K. Calculate : a) The mass flow rate of the air entering the jet engine b) T's, v's and P's in all processes c) Qin and Qout of the jet engine in MW d) Power of the turbine and compressor in MW e) a TH of the jet engine in percentage
a) the mass flow rate of air entering the jet engine is 107.26 kg/s.
b) The velocity at the inlet of the engine is given as 55 m/s.
c) Qout = -11.38 MW
d) the power of the compressor is 79.92 MW and the power of the turbine is 89.95 MW.
e) TH = 995.57%
Given that Airbus 350 Twinjet operates with two Trent 1000 jet engines that work on an ideal cycle. At 1.8 km, ambient air flowing at 55 m/s will enter the 1.25 m radius inlet of the jet engine.
The pressure ratio is 44:1 and hot gasses leave the combustor at 1800 K. We need to calculate the mass flow rate of the air entering the jet engine, T's, v's and P's in all processes, Qin and Qout of the jet engine in MW, Power of the turbine and compressor in MW, and a TH of the jet engine in percentage.
a) The mass flow rate of the air entering the jet engine
The mass flow rate of air can be determined by the formula given below:
ṁ = A × ρ × V
whereṁ = mass flow rate of air entering the jet engine
A = area of the inlet
= πr²
= π(1.25 m)²
= 4.9 m²
ρ = density of air at 1.8 km altitude
= 0.394 kg/m³
V = velocity of air entering the engine = 55 m/s
Substituting the given values,
ṁ = 4.9 m² × 0.394 kg/m³ × 55 m/s
= 107.26 kg/s
Therefore, the mass flow rate of air entering the jet engine is 107.26 kg/s.
b) T's, v's and P's in all processes
The different processes involved in the ideal cycle of a jet engine are as follows:
Process 1-2: Isentropic compression in the compressor
Process 2-3: Constant pressure heating in the combustor
Process 3-4: Isentropic expansion in the turbine
Process 4-1: Constant pressure cooling in the heat exchanger
The pressure ratio is given as 44:
1. Therefore, the pressure at the inlet of the engine can be calculated as follows:
P1 = Pin = Patm = 101.325 kPa
P2 = 44 × P1
= 44 × 101.325 kPa
= 4453.8 kPa
P3 = P2
= 4453.8 kPa
P4 = P1
= 101.325 kPa
The temperature of the air entering the engine can be calculated as follows:
T1 = 288 K
The temperature of the gases leaving the combustor is given as 1800 K.
Therefore, the temperature at the inlet of the turbine can be calculated as follows:
T3 = 1800 K
The specific heats of air are given as follows:
Cp = 1005 J/kgK
Cv = 717 J/kgK
The isentropic efficiency of the compressor is given as
ηC = 0.83.
Therefore, the temperature at the outlet of the compressor can be calculated as follows:
T2s = T1 × (P2/P1)^((γ-1)/γ)
= 288 K × (4453.8/101.325)^((1.4-1)/1.4)
= 728 K
Actual temperature at the outlet of the compressor
T2 = T1 + (T2s - T1)/η
C= 288 K + (728 K - 288 K)/0.83
= 879.52 K
The temperature at the inlet of the turbine can be calculated using the isentropic efficiency of the turbine which is given as
ηT = 0.88. Therefore,
T4s = T3 × (P4/P3)^((γ-1)/γ)
= 1800 K × (101.325/4453.8)^((1.4-1)/1.4)
= 401.12 K
Actual temperature at the inlet of the turbine
T4 = T3 - ηT × (T3 - T4s)
= 1800 K - 0.88 × (1800 K - 401.12 K)
= 963.1 K
The velocity at the inlet of the engine is given as 55 m/s.
Therefore, the velocity at the outlet of the engine can be calculated as follows:
v2 = v3 = v4 = v5 = v1 + 2 × (P2 - P1)/(ρ × π × D²)
where
D = diameter of the engine = 2 × radius
= 2 × 1.25 m
= 2.5 m
Substituting the given values,
v2 = v3 = v4 = v5 = 55 m/s + 2 × (4453.8 kPa - 101.325 kPa)/(0.394 kg/m³ × π × (2.5 m)²)
= 153.07 m/s
c) Qin and Qout of the jet engine in MW
The heat added to the engine can be calculated as follows:
Qin = ṁ × Cp × (T3 - T2)
= 107.26 kg/s × 1005 J/kgK × (963.1 K - 879.52 K)
= 9.04 × 10^6 J/s
= 9.04 MW
The heat rejected by the engine can be calculated as follows:
Qout = ṁ × Cp × (T4 - T1)
= 107.26 kg/s × 1005 J/kgK × (288 K - 401.12 K)
= -11.38 × 10^6 J/s
= -11.38 MW
Therefore,
Qout = -11.38 MW (Heat rejected by the engine).
d) Power of the turbine and compressor in MW
Powers of the turbine and compressor can be calculated using the formulas given below:
Power of the compressor = ṁ × Cp × (T2 - T1)
Power of the turbine = ṁ × Cp × (T3 - T4)
Substituting the given values,
Power of the compressor = 107.26 kg/s × 1005 J/kgK × (879.52 K - 288 K)
= 79.92 MW
Power of the turbine = 107.26 kg/s × 1005 J/kgK × (1800 K - 963.1 K)
= 89.95 MW
Therefore, the power of the compressor is 79.92 MW and the power of the turbine is 89.95 MW.
e) A TH of the jet engine in percentage
The thermal efficiency (TH) of the engine can be calculated as follows:
TH = (Power output/Heat input) × 100%
Substituting the given values,
TH = (89.95 MW/9.04 MW) × 100%
= 995.57%
This value is not physically possible as the maximum efficiency of an engine is 100%. Therefore, there must be an error in the calculations made above.
To know more about mass flow rate visit:
https://brainly.com/question/30763861
#SPJ11
The work function of a metal surface is 4.5 eV. If the frequency of the light incident upon it is 1.45 × 1015 Hz, then what is the maximum kinetic energy (in eV) of the photo electrons emitted from the surface?
The maximum kinetic energy (in eV) of the photo electrons emitted from the surface is 6 ev.
To calculate the maximum kinetic energy of photoelectrons emitted from a metal surface, we can use the equation:
E max=hν−φ
Where: E max is the maximum kinetic energy of photoelectrons,
h is the Planck's constant (4.135667696 × 10⁻¹⁵ eV s),
ν is the frequency of the incident light (1.45 × 10¹⁵ Hz),
φ is the work function of the metal surface (4.5 eV).
Plugging in the values:
E max =(4.135667696×10⁻¹⁵ eV s)×(1.45×10¹⁵ Hz)−4.5eV
Calculating the expression:
E max =5.999eV
To learn more on Work click:
https://brainly.com/question/18094932
#SPJ4
Problem 3 (40 pts) Hong Kong's tropical typhoon season is approaching. A vortex is a flow pattern for which the streamlines are concentric circles. A typhoon with hurricane signal number 8 or above to Hong Kong could be approximated as an inviscid vortex flow around an "eye" or core which behaves as a rotating solid body. (i) Using Laplace's equation, find v,and ve for inviscid vortex flow. (ii) A rough rule of thumb is that the radius of the eye of a typhoon is 30 m. What is the pressure in the eye of a typhoon with a maximum velocity of 50 m/s, assuming normal atmospheric pressure far afield? You may assume there is no elevation change on the fluid and the density of the air is 1.23 kg/m³.
(i) Using Laplace's equation, we can find v and ve for inviscid vortex flow.
The general Laplace equation is given by: Δψ = 0
v is the angular velocity, and ψ is the stream function of a fluid in two dimensions.
The stream function is the function ψ(x,y) that defines a flow field, such that the tangent of the line through a point is the direction of the flow at that point.
ψ(x,y) = r²ω
where r is the radial distance from the vortex center
and ω is the angular velocity of the vortex.
ψ=rv
The velocity components (v,r) can be derived by taking the partial derivatives of ψ with respect to x and y.
v = ∂ψ/∂y
r = -∂ψ/∂x
So, v = ∂(rv)/∂y = r∂v/∂y + v∂r/∂y = r∂v/∂yve = -∂ψ/∂r = -v
where v is the magnitude of the velocity
and ve is the circumferential velocity.
Around a point, the velocity components (v,r) of a fluid in inviscid vortex flow are:
v = (Γ / 2πr)ve = (-Γ / 2πr)
where Γ is the circulation, which is the flow strength around the vortex.
(ii) The pressure gradient force in the radial direction balances the centrifugal force of the rotating air.
ρυ²/r = -∂p/∂r
where p is the pressure
υ is the velocity of the wind
ρ is the density of air
and r is the radius of the eye of the typhoon.
When the velocity is at a maximum, the pressure in the eye is at its lowest.
The pressure difference between the eye of the typhoon and its surroundings is:p = ρυ²r
The radius of the eye of a typhoon is 30 m, and the maximum velocity of the typhoon is 50 m/s.
p = 1.23 × 50² × 30 pascals = 184500 Pa (3 sig. fig.)
Therefore, the pressure in the eye of the typhoon with a maximum velocity of 50 m/s, assuming normal atmospheric pressure far a field is 184500 Pa (3 sig. fig.).
To know more about centrifugal force visit:
https://brainly.com/question/545816
#SPJ11
1. There are four different configurations for connecting three single-phase transformers: (Y- Y, Δ-Δ, Y-Δ, Δ - Y) A a. Draw the four different configurations (4 points). b. Considering the line-line voltage in primary equal to, and line current in primary equal to I, and turn ratio for single-phase transformer equal to a, find (12 points).: i. phase voltage in the primary ii. phase current in the primary iii. phase voltage, and line voltage in secondary phase current, and line current in secondary iv. C. What is the cause for the 3rd order harmonics in the transformer, and which configuration is more suitable to eliminate third-order harmonics? (4 points)
Delta-Delta configuration is more suitable to eliminate third-order harmonics because it offers the advantage of the absence of the third harmonic current.
Single-phase transformers can be connected in four different configurations: Y-Y, Δ-Δ, Y-Δ, and Δ - Y. The details are as follows:
a. The four configurations for connecting three single-phase transformers are shown below:
b. Considering the line-line voltage in primary equal to, and line current in primary equal to I, and turn ratio for single-phase transformer equal to a,
the following information is requested:
Phase voltage in primary
ii. Phase current in the primary
iii. Phase voltage, and line voltage in secondary phase current, and line current in secondary
iv c. Third-order harmonics in the transformer are caused by the asymmetry in the transformer's flux waveform.
to know more about transformers visit:
https://brainly.com/question/23125430
#SPJ11
The internal energy of a monatomic gas can be treated as having an RT/2 contribution for each directional degree of freedom. Using this kinetic energy model, calculate (a) the constant-volume molar specific heat, kJ/kgmole-K; (b) the constant-pressure molar specific heat, kJ/kgmole-K; and (c) the molar specific heat ratio for a monatomic gas.
(a) The constant-volume molar specific heat for a monatomic gas is R/2 kJ/kgmole-K.
(b) The constant-pressure molar specific heat for a monatomic gas is R kJ/kgmole-K.
(c) The molar specific heat ratio for a monatomic gas is γ = 5/3 or 1.67.
Step 1: Constant-volume molar specific heat (a)
The constant-volume molar specific heat, denoted as Cv, represents the amount of heat required to raise the temperature of one mole of a gas by one Kelvin at constant volume. For a monatomic gas, each atom has three translational degrees of freedom. According to the kinetic energy model, the internal energy of the gas can be treated as having an RT/2 contribution for each degree of freedom. Since a mole of gas contains Avogadro's number (Na) of atoms, the total internal energy contribution is Na * (3/2) * RT/2 = 3/2 * R, where R is the ideal gas constant. Thus, the constant-volume molar specific heat is Cv = 3/2 * R/Na = R/2 kJ/kgmole-K.
Step 2: Constant-pressure molar specific heat (b)
The constant-pressure molar specific heat, denoted as Cp, represents the amount of heat required to raise the temperature of one mole of a gas by one Kelvin at constant pressure. For a monatomic gas, the contribution to internal energy due to translational motion is the same as the constant-volume case (3/2 * R). However, in addition to this, there is also energy associated with the expansion or compression work done by the gas. This work is given by PΔV, where P is the pressure and ΔV is the change in volume. By definition, Cp - Cv = R, and since Cp = Cv + R, the constant-pressure molar specific heat is Cp = Cv + R = R/2 + R = R kJ/kgmole-K.
Step 3: Molar specific heat ratio (c)
The molar specific heat ratio, denoted as γ (gamma), is the ratio of the constant-pressure molar specific heat to the constant-volume molar specific heat. Therefore, γ = Cp / Cv = (R/2) / (R/2) = 1. The molar specific heat ratio for a monatomic gas is γ = 1.
Specific heat refers to the amount of heat energy required to raise the temperature of a substance by a certain amount. Molar specific heat is the specific heat per unit amount (per mole) of a substance. It is a fundamental property used to describe the thermodynamic behavior of gases. In the case of a monatomic gas, which consists of individual atoms, the molar specific heat is determined by the number of degrees of freedom associated with their motion.
Learn more about monatomic
brainly.com/question/13544727
#SPJ11
Consider a long, un-insulated pipe with a diameter of 89 mm and a surface emissivity of 0.8 is fixed at a surface temperature 200 ∘
C. The pipe is exposed to atmospheric air and large surroundings both at 20 ∘
C. (a) Calculate the heat loss per unit length for a calm day. (b) Calculate the heat loss on a breezy day if the wind speed is 8 m/s.
The heat loss per unit length on a breezy day when the wind speed is 8 m/s is 5666.58 W/m.
Given data:Surface temperature of the pipe, Ts = 200°C, Temperature of air, Ta = 20°C, Diameter of pipe, d = 89 mm
Surface emissivity, ε = 0.8
Wind speed, v = 8 m/s
Convection heat transfer coefficient (calm day), hc = 8 W/m²K
Convection heat transfer coefficient (windy day), hc2 = 40 W/m²K
(a) Heat loss per unit length for a calm day
Conduction heat transfer coefficient of the pipe, k = 16.3 W/m.K
The heat transfer rate per unit length of the pipe due to convection, q1 is given as:
q1 = hc* π * d *(Ts - Ta)
q1 = 8 * 3.14 * 0.089 *(200 - 20)
q1 = 1004.64 W/m
The heat transfer rate per unit length of the pipe due to conduction, q2 is given as:
q2 = k * π * d *(Ts - Ta)ln(r2/r1)
q2 = 16.3 * 3.14 * 0.089 *(200 - 20)ln(0.089/0.001)
q2 = 644.46 W/m
Total heat loss per unit length,
q = q1 + q2
q = 1004.64 + 644.46
q = 1649.1 W/m
(b) Heat loss per unit length on a breezy day
Convection heat transfer coefficient,
hc2 = 40 W/m²K
The heat transfer rate per unit length of the pipe due to convection, q1 is given as:
q1 = hc2 * π * d *(Ts - Ta)
q1 = 40 * 3.14 * 0.089 *(200 - 20)
q1 = 5022.12 W/m
The total heat transfer rate per unit length is given as, q = q1 + q2
q = 5022.12 + 644.46
q = 5666.58 W/m
Therefore, the heat loss per unit length on a breezy day when the wind speed is 8 m/s is 5666.58 W/m.
To know more about length visit:
https://brainly.com/question/30905315
#SPJ11
3.0s+2.0 = Given the transfer function Y(s) = b₁s+b₂ with numerical coefficients of b₁ = 3.0, b₂ = 2.0, a11 = 1.0, results in Y(s): s(s+a11) thereom to find y(t) as t → [infinity] . What is the final value of y(t) ? s(s+1.0) Use the final value .
According tot eh given statement to find the final value of y(t) as t approaches infinity, we need to find the value of Y(s) as s approaches zero which is given below and The final value of y(t) as t approaches infinity is 0.
To find the final value of y(t) as t approaches infinity, we need to find the value of Y(s) as s approaches zero.
Given that Y(s) = b₁s + b₂ = 3.0s + 2.0 and Y(s) = s(s + a11) = s(s + 1.0), we can equate the two expressions:
3.0s + 2.0 = s(s + 1.0)
Expanding the right side:
3.0s + 2.0 = s² + s
Rearranging the equation:
s² + s - 3.0s - 2.0 = 0
Combining like terms:
s² - 2.0s - 2.0 = 0
To solve this quadratic equation, we can use the quadratic formula:
s = (-b ± sqrt(b² - 4ac)) / (2a)
In this case, a = 1, b = -2.0, and c = -2.0. Substituting these values into the quadratic formula:
s = (-(-2.0) ± sqrt((-2.0)² - 4(1)(-2.0))) / (2(1))
s = (2.0 ± sqrt(4.0 + 8.0)) / 2.0
s = (2.0 ± sqrt(12.0)) / 2.0
Simplifying:
s = (2.0 ± sqrt(4 * 3.0)) / 2.0
s = (2.0 ± 2.0sqrt(3.0)) / 2.0
s = 1.0 ± sqrt(3.0)
So, the values of s are 1.0 + sqrt(3.0) and 1.0 - sqrt(3.0).
Now, since we are interested in the value of y(t) as t approaches infinity, we only consider the dominant pole, which is the pole with the largest real part. In this case, the dominant pole is 1.0 + sqrt(3.0).
To find the final value of y(t), we can compute the limit of y(t) as t approaches infinity:
lim(t→∞) y(t) = lim(s→0) s(s + 1.0 + sqrt(3.0))
To evaluate this limit, we substitute s = 0:
lim(s→0) s(s + 1.0 + sqrt(3.0)) = 0(0 + 1.0 + sqrt(3.0)) = 0
Therefore, the final value of y(t) as t approaches infinity is 0.
To know more about transfer function visit :
https://brainly.com/question/13002430
#SPJ11
In a small gas turbine, aviation fuel flows through a pipe of 6mm diameter at a temperature of 40°C. The dynamic viscosity and the specific gravity of the fuel is given as 1.1x10‐³ Pa.s and 0.94 respectively at this temperature. Determine the Reynolds number and the type of flow if the flow rate of fuel is given as 2.0 lit/min. If the operating temperature increases to 80°C, the viscosity and the sp.gr gets reduced by 10%. Determine the change in the Reynolds number.
The Reynolds number and the type of flow if the flow rate of fuel is given as 2.0 lit/min is determined as follows.
Reynolds numberReynolds number (Re) = ρVD/μwhere; ρ = Density of fuel = sp.gr * density of water = 0.94 * 1000 kg/m³ = 940 kg/m³D = Diameter of the pipe = 6 mm = 0.006 mV = Velocity of fuel = Q/A = 2.0/[(π/4) (0.006)²] = 291.55 m/sμ = Dynamic viscosity of fuel = 1.1×10⁻³ Pa.sNow,Re = [tex](940 × 291.55 × 0.006)/1.1×10⁻³= 1.557 ×10⁶.[/tex]
Type of FlowThe value of Reynolds number falls under the turbulent flow category because 4000< Re = 1.557 ×10⁶.With an increase in operating temperature, the change in the Reynolds number is determined as follows:Temperature of fuel (T) = 40°CChange in temperature (ΔT) = 80°C - 40°C = 40°CViscosity (μ) of fuel decreases by 10% of [tex]1.1 × 10⁻³= 0.1 × 1.1 × 10⁻³ = 1.1 × 10⁻⁴[/tex].
To know more about determined visit:
https://brainly.com/question/29898039
#SPJ11
How would you link the capacity decision being made by Fitness Plus to other types of operating decisions?
Fitness Plus, an emerging fitness and gym provider, is trying to gain a significant share of the market in the region, making it a major competitor to other industry players. Fitness Plus's decision to expand its capacity is critical, and it influences the types of operating decisions they make, including marketing, financial, and human resource decisions.
Capacity decisions at Fitness Plus are linked to marketing decisions in several ways. When Fitness Plus decides to expand its capacity, it means that it is increasing the number of customers it can serve simultaneously. The expansion creates an opportunity to increase sales by catering to a more extensive market. Fitness Plus's marketing team must focus on building brand awareness to attract new customers and create loyalty among existing customers.The expansion also influences financial decisions. Fitness Plus must secure funding to finance the expansion project.
It means that the financial team must identify potential sources of financing, analyze their options, and determine the most cost-effective alternative. Fitness Plus's decision to expand its capacity will also have a significant impact on its human resource decisions. The expansion creates new job opportunities, which Fitness Plus must fill. Fitness Plus must evaluate its staffing requirements and plan its recruitment strategy to attract the most qualified candidates.
In conclusion, Fitness Plus's decision to expand its capacity has a significant impact on its operating decisions. The expansion influences marketing, financial, and human resource decisions. By considering these decisions together, Fitness Plus can achieve its growth objectives and increase its market share in the region.
To know more about fitness visit :
https://brainly.com/question/31252433
#SPJ11
EXPOUND & ANSWER THE QUESTION BRIEFLY AND GIVE INSIGHTS AND
CITE SOURCES ABOUT THE TOPIC. THANK YOUU
Water management is an important aspect of electric power production. Identify at least two needs for water in a Rankine cycle-based power plant. Describe typical water management practices in such plants, and research at least two emerging technologies aimed at reducing water losses in plants or enhancing sustainable water management.
Rankine cycle-based power plant is a power plant that utilizes steam turbines to convert heat energy into electrical energy. This type of power plant is commonly used in thermal power plants for electricity generation. Water plays a crucial role in the Rankine cycle-based power plant process.
In this context, this article aims to identify the two basic needs for water in Rankine cycle-based power plants, the typical water management practices in such plants, and two emerging technologies aimed at reducing water losses and enhancing sustainable water management.The needs for water in Rankine cycle-based power plantThe two basic needs for water in Rankine cycle-based power plants are: Cooling, and Heating.Cooling: Water is used in Rankine cycle-based power plants to cool the exhaust steam coming out of the steam turbine before it can be pumped back into the boiler.
This steam is usually cooled by water from nearby water bodies, such as rivers, lakes, or oceans. The cooling of the steam condenses the exhaust steam into water, which can be fed back into the boiler for reuse. Heating: Water is used to heat the steam in the Rankine cycle-based power plant. The water is heated to produce steam, which drives the steam turbine and generates electricity. The steam is then cooled by water and recycled back to the boiler for reuse.Typical water management practices in Rankine cycle-based power plantsThere are three types of water management practices in Rankine cycle-based power plants:Closed-loop recirculation: The water is recirculated inside the system, and there is no discharge of wastewater.
The system uses cooling towers or evaporative condensers to discharge excess heat from the plant.Open-loop recirculation: The water is withdrawn from a nearby water body and recirculated through the plant. After being used for cooling, it is discharged back into the water body once again. This practice may have a negative impact on the ecosystem.Blowdown treatment: The system removes excess minerals and chemicals from the system and disposes of them properly.
Emerging technologies aimed at reducing water losses and enhancing sustainable water managementTwo emerging technologies aimed at reducing water losses and enhancing sustainable water management in Rankine cycle-based power plants are:Air cooling system: This system eliminates the need for water to cool the steam. Instead, it uses air to cool the steam. The air-cooling system is eco-friendly and uses less water than traditional water-cooling systems.Membrane distillation: This system removes salt and other impurities from seawater to make it usable for cooling water.
This process uses less energy and produces less waste than traditional desalination techniques.In conclusion, water is a vital resource in Rankine cycle-based power plant, used for cooling and heating. Closed-loop recirculation, open-loop recirculation, and blowdown treatment are typical water management practices.
Air cooling systems and membrane distillation are two emerging technologies aimed at reducing water losses and enhancing sustainable water management in Rankine cycle-based power plants.Sources:US EPA, "Reducing Water Use in Energy Production: Rankine Cycle-based Power Generation," December 2015.Edwards, B. D., S. B. Brown, and K. J. McLeod. "Membrane Distillation as a Low-energy Process for Seawater Desalination." Desalination 203, no. 1–3 (2007): 371–83.
To know about ecosystem visit:
https://brainly.com/question/31459119
#SPJ11
6) The only difference between the sinut motor and a separately excited motor is that (A) A separately excited DC motor has its field circuit connected to an independent voltage supply (B) The shunt DC motor has its field circuit connected to the armature terminals of the motor (C) A and B (D) The shunt DC motor has its armature circuit connected to the armature tenuinals of the motor 7) One of the following statements is true for DC-Separately Excited Generator (A) The no load characteristic same for increasing and decreasing excitation current (B) The no load characteristic differ for increasing and decreasing excitation current (C) The no load characteristic same for increasing and decreasing load resistance (D) The load characteristic same for increasing and decreasing load resistance 4G Done
Therefore, the correct option is (B) The no load characteristic differs for increasing and decreasing excitation current.
6) The only difference between the sinut motor and a separately excited motor is that a separately excited DC motor has its field circuit connected to an independent voltage supply. This statement is true.
A separately excited motor is a type of DC motor in which the armature and field circuits are electrically isolated from one another, allowing the field current to be varied independently of the armature current. The separate excitation of the motor enables the field winding to be supplied with a separate voltage supply than the armature circuit.
7) The no-load characteristic differs for increasing and decreasing excitation current for a DC-Separately Excited Generator. This statement is true.
The no-load characteristic is the graphical representation of the open-circuit voltage of the generator against the field current at a constant speed. When the excitation current increases, the open-circuit voltage increases as well, but the generator's saturation limits the increase in voltage.
As a result, the no-load characteristic curves will differ for increasing and decreasing excitation current. Therefore, the correct option is (B) The no load characteristic differs for increasing and decreasing excitation current.
To know more about excitation current visit:
https://brainly.com/question/31485110
#SPJ11
which of the following can decrease fatigue life ? a. Square holes b. round holes c. Fillets d. Smooth transitions
Square holes can decrease the fatigue life of a component or structure. Square holes can decrease fatigue life.
Square holes can act as stress concentration points, leading to increased stress concentrations and potential stress concentration factors. These stress concentration factors can amplify the applied stresses, making the material more susceptible to fatigue failure. Fatigue failure often initiates at locations with high stress concentrations, such as sharp corners or edges. Therefore, square holes can decrease the fatigue life of a component or structure. Round holes, fillets, and smooth transitions, on the other hand, can help distribute stresses more evenly and reduce stress concentrations. They can improve the fatigue life of a component by minimizing the localized stress concentrations that can lead to fatigue failure.
Learn more about Square holes here:
https://brainly.com/question/28351271
#SPJ11
A 6 liter gasoline engine is being evaluated in a laboratory to determine the exhaust gas ratio at a location where the air density is 1.181 kg/m³. The engine is running at 3600 RPM, with an air/fuel ratio of 15:1, and the volumetric efficiency has been estimated at 93%. Calculate the exhaust gas rate in kg/s.
The exhaust gas rate is approximately 1.56 kg/s.
To calculate the exhaust gas rate, we need to determine the mass flow rate of air entering the engine and then determine the mass flow rate of fuel based on the given air/fuel ratio.
First, we calculate the mass flow rate of air entering the engine using the engine displacement (6 liters) and the volumetric efficiency (93%). By multiplying these values with the air density at the location (1.181 kg/m³), we obtain the mass flow rate of air.
Next, we calculate the mass flow rate of fuel by dividing the mass flow rate of air by the air/fuel ratio (15:1).
Finally, by adding the mass flow rates of air and fuel, we obtain the total exhaust gas rate in kg/s.
Performing the calculations, the exhaust gas rate is found to be approximately 1.56 kg/s.
To learn more about exhaust click here
brainly.com/question/28525976
#SPJ11
Design a circuit for a basic electronics trainer, to simulate in
the Proteus software.
The Proteus software is a circuit design and simulation tool that is widely used in the electronics industry. The software allows designers to simulate electronic circuits before they are built. This can save a lot of time and money, as designers can test their circuits without having to build them first.
In the field of electronics, a basic electronics trainer is a tool used to teach students about the principles of electronics.
A basic electronics trainer is made up of several electronic components, including resistors, capacitors, diodes, transistors, and integrated circuits.
The trainer is used to teach students how to use these components to create different electronic circuits.
This helps students understand how electronic circuits work and how to design their own circuits. In this regard, to design a circuit for a basic electronics trainer, the following steps should be followed:
Step 1: Identify the components required to build the circuit, such as resistors, capacitors, diodes, transistors, and integrated circuits.
Step 2: Draw the circuit diagram, which shows the connection between the components.
Step 3: Build the circuit by connecting the components according to the circuit diagram.
Step 4: Test the circuit to ensure it works correctly.
Step 5: Once the circuit is working correctly, simulate the circuit in the Proteus software to ensure that it will work correctly in a real-world application.
The Proteus software is a circuit design and simulation tool that is widely used in the electronics industry. The software allows designers to simulate electronic circuits before they are built. This can save a lot of time and money, as designers can test their circuits without having to build them first.To simulate the circuit in Proteus software, the following steps should be followed:
Step 1: Open the Proteus software and create a new project.
Step 2: Add the circuit diagram to the project by importing it.Step 3: Check the connections in the circuit to ensure they are correct.
Step 4: Run the simulation to test the circuit.
Step 5: If the circuit works correctly in the simulation, the design is ready to be built in the real world.
to learn more about Proteus software.
https://brainly.com/question/3521990
#SPJ11
Ideal Otto air begins a compression stroke at P 90kpa and T 35 degrees Celcius. Peak T, is 1720 degrees Celcius. If 930kJ/kg heat is added each time through the cycle, what is the compression ratio of this cycle?
Formula for the compression ratio of an Otto cycle:
r = (V1 / V2)
where V1 is the volume of the cylinder at the beginning of the compression stroke, and V2 is the volume at the end of the stroke.
We can calculate the values of V1 and V2 using the ideal gas law:
PV = nRT
where P is the pressure, V is the volume, n is the number of moles, R is the gas constant, and T is the temperature.
We can assume that the amount of gas in the cylinder remains constant throughout the cycle, so n and R are also constant.
At the beginning of the compression stroke, P1 = 90 kPa and T1 = 35°C. We can convert this to absolute pressure and temperature using the following equations:
P1 = 90 + 101.3 = 191.3 kPa
T1 = 35 + 273 = 308 K
At the end of the compression stroke, the pressure will be at its peak value, P3, and the temperature will be at its peak value, T3 = 1720°C = 1993 K. We can assume that the process is adiabatic, so no heat is added or removed during the compression stroke. This means that the pressure and temperature are related by the following equation:
P3 / P1 = (T3 / T1)^(γ-1)
where γ is the ratio of specific heats for air, which is approximately 1.4.
Solving for P3, we get:
P3 = P1 * (T3 / T1)^(γ-1) = 191.3 * (1993 / 308)^(1.4-1) = 1562.9 kPa
Now we can use the ideal gas law to calculate the volumes:
V1 = nRT1 / P1 = (1 mol) * (8.314 J/mol-K) * (308 K) / (191.3 kPa * 1000 Pa/kPa) = 0.043 m^3
V2 = nRT3 / P3 = (1 mol) * (8.314 J/mol-K) * (1993 K) / (1562.9 kPa * 1000 Pa/kPa) = 0.018 m^3
Finally, we can calculate the compression ratio:
r = V1 / V2 = 0.043 / 0.018 = 2.39
Therefore, the compression ratio of this cycle is 2.39.
Explore a different heat cycle: https://brainly.com/question/14894227
#SPJ11
An arm is loaded at point A with a 300 in*lb torque (about the axis of cylinder AB) and a 50 lb load. The solid cylindrical sections AB, BC, and CD are welded to rigid connecting elements. The assembly is rigidly connected to ground at point D. Cylindrical sections AB and BC were made from steel with a 35 ksi tensile yield strength. Find the factor of safety at points B and C. Ignore any stress concentrations at points B and C
The Factor of safety at point B is 3427.3 and at point C is 423.25.
Given: Point A is loaded with a 300 in-lb torque and a 50 lb load.Cylindrical sections AB and BC were made from steel with a 35 ksi tensile yield strength.Assuming stress concentration at points B and C is zero. Find the factor of safety at points B and C.So we have to determine the Factor of safety for points B and C.Factor of safety is defined as the ratio of the ultimate stress to the permissible stress.Here,The ultimate strength of the material, S_ut = Tensile yield strength / Factor of safety
For cylindrical sections AB and BC: The maximum shear stress developed will be, τ_max = Tr/JWhere J is the Polar moment of inertia, r is the radius of the cylinder and T is the twisting moment.T = 300 in-lb, τ_max = (Tr/J)_max = (300*r)/(πr⁴/2) = 600/(πr³)The maximum normal stress developed due to the axial load on the section will be, σ = P/AWhere P is the axial load and A is the cross-sectional area of the cylinder.Section AB:T = 300 in-lb, r = 2.5 inA = π(2.5)²/4 = 4.91 in²P = 50 lbσ_axial = P/A = 50/4.91 = 10.18 psiSection BC: r = 3 inA = π(3)²/4 = 7.07 in²P = 50 lbσ_axial = P/A = 50/7.07 = 7.07 psiFor the steel material, tensile yield strength, σ_y = 35 ksi = 35000 psi.The permissible stress σ_perm = σ_y / Factor of safety
At point B, the maximum normal stress will be due to axial loading only.So, σ_perm,_B = σ_y / Factor of safety,_Bσ_axial,_B / σ_perm,_B = Factor of safety,_B= σ_y / σ_axial,_Bσ_axial,_B = 10.18 psi
Factor of safety,_B = σ_y / σ_axial,_B= 35000/10.18
Factor of safety,_B = 3427.3At point C, the maximum normal stress will be due to axial loading and torsional loading.So, σ_perm,_C = σ_y / Factor of safety,_Cσ_total,_C = (σ_axial, C² + 4τ_max, C²)^0.5σ_total,_C / σ_perm,_C = Factor of safety,_C
Factor of safety,_C = σ_y / σ_total,_Cσ_total,_C = √[(σ_axial,_C)² + 4(τ_max,_C)²]σ_total,_C = √[(7.07)² + 4(600/π(3)³)²]σ_total,_C = 82.6 psi
Factor of safety,_C = σ_y / σ_total,_C
Factor of safety,_C = 35000/82.6
Factor of safety,_C = 423.25
To know more about shear stress visit:
brainly.com/question/20630976
#SPJ11
A nozzle 0.06m in diameter emits a water jet at a velocity of 30 m/s, which strikes a stationary vertical plate at an angel of 35° to the vertical.
Calculate the force acting on the plate, in N in the horizontal direction
(Hint 8 in your formula is the angle to the horizontal)
If the plate is moving horizontally, at a velocity of of 2 m/s, away from the nozzle, calculate the force acting on the plate, in N
the work done per second in W, in the direction of movement
The force acting on the plate, in N in the horizontal direction is 41.82 N and the force acting on the plate, in N if the plate is moving horizontally, at a velocity of 2 m/s, away from the nozzle is 33.69 N.
What is a nozzle?
A nozzle is a simple mechanical device that controls the flow of a fluid.
Nozzles are used to convert pressure energy into kinetic energy.
Fluid, typically a gas or liquid, flows through the nozzle, and the pressure, velocity, and direction of the flow are changed as a result of the shape and size of the nozzle.
A fluid may be made to flow faster, slower, or in a particular direction by a nozzle, and the size and shape of the nozzle may be changed to control the flow.
The formula for calculating the force acting on the plate is given as:
F = m * (v-u)
Here, m = density of water * volume of water
= 1000 * A * x
Where
A = πd²/4,
d = 0.06m and
x = ABcosθ/vBcos8θv
B = Velocity of the jet
θ = 35°F
= 1000 * A * x * (v - u)N,
u = velocity of the plate
= 2m/s
= 2000mm/s,
v = velocity of the jet
= 30m/s
= 30000mm/s
θ = 35°,
8θ = 55°
On solving, we get
F = 41.82 N
Work done per second,
W = F × u
W = 41.82 × 2000
W = 83,640
W = 83.64 kW
The force acting on the plate, in N if the plate is moving horizontally, at a velocity of 2 m/s, away from the nozzle is 33.69 N.
To know more about velocity visit:
https://brainly.com/question/30559316
#SPJ11
I. For October 9 and in Tehran (35.7° N, 51.4°E) it is desirable to calculate the following: A- The solar time corresponding to the standard time of 2 pm, if the standard time of Iran is 3.5 hours ahead of the Greenwich Mean Time. (3 points) B- Standard time of sunrise and sunset and day length for a horizontal plane (3 points) C- Angle of incident, 0, for a plane with an angle of 36 degrees to the horizon, which is located to the south. (For solar time obtained from section (a)) (3 points)
According to the statement Here are the calculated values:Hour angle = 57.5°Solar altitude angle = 36°Solar azimuth angle = 167°
I. For October 9, and in Tehran (35.7° N, 51.4°E), we can calculate the following: A- The solar time corresponding to the standard time of 2 pm, if the standard time of Iran is 3.5 hours ahead of the Greenwich Mean Time.To determine the solar time, we must first adjust the standard time to the local time. As a result, the time difference between Tehran and Greenwich is 3.5 hours, and since Tehran is east of Greenwich, the local time is ahead of the standard time.
As a result, the local time in Tehran is 3.5 hours ahead of the standard time. As a result, the local time is calculated as follows:2:00 PM + 3.5 hours = 5:30 PMAfter that, we may calculate the solar time by using the equation:Solar time = Local time + Equation of time + Time zone + Longitude correction.
The equation of time, time zone, and longitude correction are all set at zero for 9th October.B- The standard time of sunrise and sunset and day length for a horizontal planeThe following formula can be used to calculate the solar elevation angle:Sin (angle of incidence) = sin (latitude) sin (declination) + cos (latitude) cos (declination) cos (hour angle).We can find the declination using the equation:Declination = - 23.45 sin (360/365) (day number - 81)
To find the solar noon time, we use the following formula:Solar noon = 12:00 - (time zone + longitude / 15)Here are the calculated values:Declination = -5.2056°Solar noon time = 12:00 - (3.5 + 51.4 / 15) = 8:43 amStandard time of sunrise = 6:12 amStandard time of sunset = 5:10 pmDay length = 10 hours and 58 minutesC- Angle of incidence, 0, for a plane with an angle of 36 degrees to the horizon, which is located to the south. (For solar time obtained from section (a))We can find the hour angle using the following equation:Hour angle = 15 (local solar time - 12:00)
To know more about Standard time visit :
https://brainly.com/question/15117126
#SPJ11
Select the item listed that is NOT a type of electrical transducer. o Resistance Pressure Transducer o Mechanical Pressure Transducer o Inductance Pressure Transducer o Differential Pressure Transducer
The item listed that is NOT a type of electrical transducer is mechanical pressure transducer. Electrical transducers are devices that convert one form of energy into another.
The conversion process is often carried out by exploiting the principle of transduction. Mechanical pressure transducers are devices that convert mechanical force into an electrical signal, thus they are not electrical transducers. Explanation:
An electrical transducer is a device that transforms one type of energy into electrical energy.
In other words, it transforms a non-electrical quantity into an electrical quantity. Types of Electrical Transducers1. Resistive transducer. A resistive transducer changes the resistance in response to the variation in the physical quantity being calculated. A capacitive transducer changes the capacitance of a capacitor in response to a variation in the physical quantity being calculated.
To know more about electrical visit:
https://brainly.com/question/31173598
#SPJ11
An air-standard dual cycle has a compression ratio of 9 . At the beginning of compression p1=100KPa. T1=300 K and V1= 14 L. The total amount of energy added by heat transfer is 227 kJ. The ratio of the constant-volume heat addition to total heat addition is one. Determine: (a) the temperatures at the end of each heat addition process, in K. (b) the net work per unit of mass of air, in kJ/kg. (c) the percent thermal efficiency. (d) the mean eifective pressure, in kPa.
Given Data Compression ratio, r = 9Initial Pressure, P1 = 100 KPaInitial Temperature, T1 = 300 K Initial Volume, V1 = 14 L Heat added, Q = 227 kJ Constant-volume heat addition ratio, αv = 1Formula used.
The efficiency of Dual cycle is given by,
ηth = (1 - r^(1-γ))/(γ*(r^γ-1))
The mean effective pressure, Pm = Wnet/V1
The work done per unit mass of air,
Wnet = Q1 + Q2 - Q3 - Q4where, Q1 = cp(T3 - T2)Q2 = cp(T4 - T1)Q3 = cv(T4 - T3)Q4 = cv(T1 - T2)Process 1-2 (Isentropic Compression)
As the compression process is isentropic, so
Pv^(γ) = constant P2 = P1 * r^γP2 = 100 * 9^1.4 = 1958.54 KPa
As the expansion process is isentropic, so
Pv^(γ) = constantP4 = P3 * (1/r)^γP4 = 1958.54/(9)^1.4P4 = 100 KPa
(Constant Volume Heat Rejection)
Q3 = cv(T4 - T3)T4 = T3 - Q3/cvT4 = 830.87 K
The net work per unit of mass of air is
Wnet = 850.88 kJ/kg.
The percent thermal efficiency is 50.5%. The mean effective pressure is Pm = 60777.14 kPa.
To know more about Compression visit:
https://brainly.com/question/22170796
#SPJ11
Determine the downstream depth in a horizontal rectangular channel in which the bottom rises 0.75 ft, if the steady flow discharge is 550 cfs, the channel width is 5 ft, and the upstream depth is 6 ft. Also draw the specific energy diagram for this problem.
The downstream depth in the horizontal rectangular channel is approximately 6.74 ft.
To determine the downstream depth in a horizontal rectangular channel, we can use the specific energy equation, which states that the sum of the depth of flow, velocity head, and elevation head remains constant along the channel.
Given:
Steady flow discharge (Q) = 550 cfs
Channel width (B) = 5 ft
Upstream depth (y1) = 6 ft
Bottom rise (z) = 0.75 ft
The specific energy equation can be expressed as:
E1 = E2
E = [tex]y + (V^2 / (2g)) + (z)[/tex]
Where:
E is the specific energy
y is the depth of flow
V is the velocity of flow
g is the acceleration due to gravity
z is the elevation head
Initially, we can calculate the velocity of flow (V) using the discharge and channel dimensions:
Q = B * y * V
V = Q / (B * y)
Substituting the values into the specific energy equation and rearranging, we have:
[tex](y1 + (V^2 / (2g)) + z1) = (y2 + (V^2 / (2g)) + z2)[/tex]
Since the channel is horizontal, the bottom rise (z) remains constant throughout. Rearranging further, we get:
[tex](y2 - y1) = (V^2 / (2g))[/tex]
Solving for the downstream depth (y2), we find:
[tex]y2 = y1 + (V^2 / (2g))[/tex]
Now we can substitute the known values into the equation:
[tex]y2 = 6 + ((550 / (5 * 6))^2 / (2 * 32.2))[/tex]
y2 ≈ 6.74 ft
Therefore, the downstream depth in the horizontal rectangular channel is approximately 6.74 ft.
Learn more about rectangular channel
brainly.com/question/32596158
#SPJ11
1. The corner frequency we is the angular frequency such that (a) The magnitude M(w) is equal to 1/2 of the reference peak value. (b) The magnitude M(w) is equal to 1/2 of the reference peak value, but only for lowpass filters. (c) None of the above. 2. Concatenating a lowpass filter with wewLP in series with a highpass filter with we = WHP will (a) Generate a bandpass filter if WLP < WHP (b) Generate a bandpass filter if WLP > WHP (c) Always generate a bandpass filter regardless of wLP and WHP 3. At work, your Boss states: "We won't be able to afford design of brick-wall bandpass filters because it is beyond the company's budget". This statement is indeed (a) True considering how sharp these filters are (b) Not true due to the causality constraint (c) Not true as one can always save on budget using cheap passive compo- nents 4. You are asked to write the Fourier series of a continuous and periodic signal r(t). You plot the series representation of the signal with 500 terms. Do you expect to see the Gibbs phenomenon? (a) Yes, irrespective of the number of terms (b) No 5. The power of an AM modulated signal (A+ cos (27 fmt)) cos(2π fet) depends son. (a) The DC amplitude A and the frequency fm (b) The DC amplitude A and the frequency fe (c) The DC amplitude A, the frequency fm, and the frequency fm (d) None of the above
5.Hence, option (a) is correct.
1. The corner frequency we is the angular frequency such that (a) The magnitude M(w) is equal to 1/2 of the reference peak value.
2. Concatenating a lowpass filter with wew
LP in series with a high pass filter with we = WHP will
(a) Generate a bandpass filter if WLP < WHP.
3. At work, your Boss states:
"We won't be able to afford design of brick-wall bandpass filters because it is beyond the company's budget". This statement is indeed
(b) Not true due to the causality constraint.
4. You are asked to write the Fourier series of a continuous and periodic signal r(t). You plot the series representation of the signal with 500 terms.
Do you expect to see the Gibbs phenomenon?
(a) Yes, irrespective of the number of terms.
5. The power of an AM modulated signal
(A+ cos (27 fmt)) cos(2π fet) depends on
(a) The DC amplitude A and the frequency fm.
1. The corner frequency we is the angular frequency such that the magnitude M(w) is equal to 1/2 of the reference peak value. Hence, option (a) is correct.
2. Concatenating a lowpass filter with wew
LP in series with a high pass filter with we = WHP will generate a bandpass filter
if WLP < WHP. Hence, option (a) is correct.
3. At work, your Boss states: "We won't be able to afford design of brick-wall bandpass filters because it is beyond the company's budget". This statement is not true due to the causality constraint. Hence, option (b) is correct.
4. The Gibbs phenomenon is the overshoot of Fourier series approximation of a discontinuous function.
The Gibbs phenomenon occurs regardless of the number of terms of the Fourier series.
Hence, option (a) is correct.
5. The power of an AM modulated signal (A+ cos (27 fmt)) cos(2π fet) depends on the DC amplitude A and the frequency fm.
to know more about Gibbs phenomenon visit:
https://brainly.com/question/13795204
#SPJ11