Answer:
They would go out
Explanation:
This is because, in a series connection, the same current passes through each light. Since the current is the same, if one light burns out, it cuts off the rest of the other lights and thus, no current flows in the string again.
Whereas, in a parallel connection, each light is attached to its own wire and thus has a different current flowing through it than the rest of the other wires. If one of the lights goes out, current stops flowing through it but, it doesn't affect the other lights.
help meee plisssssssssssssssssssssssssssss
Answer:
Resistance = 0.22 Ohms
Current = 13.63636 A
Explanation:
Total resistance for resistors in parallel is given by:
[tex]\frac{1}{T} =\frac{1}{R1} +\frac{1}{R2} +...+\frac{1}{Rn}[/tex] where n is the number of resistors
[tex]\frac{1}{T} = \frac{1}{1.1} +\frac{1}{1.1} +\frac{1}{1.1} +\frac{1}{1.1} +\frac{1}{1.1}[/tex]
if you solve that you get [tex]\frac{1}{T} = 5/1.1 \\\\T = 1.1/5T = 0.22 Ohms[/tex]
Solve current using V=IR
I=V/R =
I=3/0.22
I = 13.63636 A
A metal pot feels hot to the touch after a short time on the shove. what type of material is the metal pot
Most stars are _____ compared to the sun.
slightly smaller
much bigger
much smaller
slightly bigger
Under the influence of its drive force, a snowmobile is moving at a constant velocity along a horizontal patch of snow. When the drive force is shut off, the snowmobile coasts to a halt. The snowmobile and its rider have a mass of 128 kg. Under the influence of a drive force of 195 N, it is moving at a constant velocity whose magnitude is 5.90 m/s. The drive force is then shut off. Find (a) the distance in which the snowmobile coasts to a halt and (b) the time required to do so.
Answer:
a) Δx = 11.6 m
b) t = 3.9 s
Explanation:
a)
Since the snowmobile is moving at constant speed, and the drive force is 195 N, this means that thereis another force equal and opposite acting on it, according to Newton's 2nd Law, due to there is no acceleration present in the horizontal direction .This force is just the force of kinetic friction, and is equal to -195 N (assuming the positive direction as the direction of the movement).Once the drive force is shut off, the only force acting on the snowmobile remains the friction force.According Newton's 2nd Law, this force is causing a negative acceleration (actually slowing down the snowmobile) that can be found as follows:[tex]a = \frac{F_{fr} }{m} = \frac{-195N}{128kg} = -1.5 m/s2 (1)[/tex]
Assuming the friction force keeps constant, we can use the following kinematic equation in order to find the distance traveled under this acceleration before coming to an stop, as follows:[tex]v_{f} ^{2} -v_{o} ^{2} = 2* a* \Delta x (2)[/tex]
Taking into account that vf=0, replacing by the given (v₀) and a from (1), we can solve for Δx, as follows:[tex]\Delta x =- \frac{v_{o}^{2}}{2*a} =- \frac{(5.90m/s)^{2}}{2*(-1.5m/s2)} = 11.6 m (3)[/tex]
b)
We can find the time needed to come to an stop, applying the definition of acceleration, as follows:[tex]v_{f} = v_{o} + a*\Delta t (4)[/tex]
Since we have already said that the snowmobile comes to an stop, this means that vf = 0.Replacing a and v₀ as we did in (3), we can solve for Δt as follows:[tex]\Delta t = \frac{-v_{o} }{a} = \frac{-5.9m/s}{-1.5m/s2} = 3.9 s (5)[/tex]
Read the following statements. Which statement provides the correct definition of weather? Select your answer from the options below. * 1 point
Atmospheric conditions at a specific time in a specific area
Atmospheric conditions over a period of time in a specific area
Average atmospheric conditions over a period of time in a region
Average atmospheric conditions across the world
Answer:
In one day, a store sells 14 pairs of jeans. The 14 jeans represent 20% of the total number of items sold that day. How many items did the store sell in one day? Explain or show how you got your answer.
plz help with the qsn
Explanation:
Help me with both questions please?
Answer:
1. They all accelerate at the same rate.
2.The object travels at a constant velocity throughout the fall.
Explanation:
Earths gravitational pull is at a constant 9.08 m/s^2. so when objects are free falling, the objects in question can only fall so fast before it would break gravity so to speak.
Which DOES NOT happen during the phase change from liquid to solid?
Kinetic energy decreases
Particles move slower
Freezing occurs
Temperature increases
Answer:
Temperature increases
During the phase transition from liquid to solid, kinetic energy diminishes, particles move slower, and freezing occurs.
Phase change:Extreme heat is more likely to occur as a result of rising temperatures, and it will last longer. Heatwaves can indeed be deadly, resulting in manifestations including heat kinks and heat exhaustion, as well as death.
Warmer temperatures have the potential to trigger a cascade of other changes around the world.The greenhouse effect is worsened by these gas emissions, which cause the earth's crust temperature to rise. Burning fossil fuels has the greatest impact on climate change of any human activity.Since in changement from liquid to solid the temperature will decrease.Therefore, the final answer is "Temperature increases".
Find out more about the phase change here:
brainly.com/question/11490613
he inductance of a tuning circuit of an AM radio is 4 mH. Find the capacitance of the circuit required for reception at 1200 kHz.
Answer:
4.4pF
Explanation:
the capacitance of the circuit required for reception is given:
wL = [tex]\frac{1}{wC}[/tex]
w = 2π [tex]f[/tex]
Using both equation
Capacitance is given
C = 1 - 4π2 f2 L
1- 4×9.8969×144×10 10 ×0.004
=4.4pF
In the “Elastic Collision" part of this activity, what happened to the momentum of the red cart after the collision? What happened to the momentum of the blue cart after the collision?
Explanation:
Elastic collision between balls of equal mass viimis 1.5 mys 1.5m/s 1! mis ... Make a data table for the following: mass, velocity and momentum of each ball before ... Part 2 moving faster. ... Summary: Describe the main ideas learned in this activity regarding initial and ... Collision 2: Blue Cart Moving Slower than the Red Cart.
You are tasked with calibrating the springs for a pinball machine. Your method of testing the springs is by attaching masses onto the end of the springs and measuring the stretch from initial position to final position. You hang a 14kg mass on a spring and notice that it stretches from 50 to 78cm. What is the spring constant for that spring
Answer:
[tex]490.5\ \text{N/m}[/tex]
Explanation:
m = Mass attached to spring = 14 kg
g = Acceleration due to gravity = [tex]9.81\ \text{m/s}^2[/tex]
x = Displacement of spring = [tex]78-50=28\ \text{cm}[/tex]
k = Spring constant
The force balance of the system is given by
[tex]kx=mg\\\Rightarrow k=\dfrac{mg}{x}\\\Rightarrow k=\dfrac{14\times 9.81}{0.28}\\\Rightarrow k=490.5\ \text{N/m}[/tex]
The spring constant for that spring is [tex]490.5\ \text{N/m}[/tex].
The new roller coaster at Carowinds flies along at 80 m/s. How long does it take to
travel 16000 meters of track?
What is one disadvantage of sending information over long distances
wirelessly using digital signals?
O A. The signals become weaker the farther the receiver is from the
source.
B. The farther the signals travel, the more slowly they move.
C. The signals become stronger the farther the receiver is from the
source.
O D. The farther the signals travel, the easier they are to detect.
The disadvantage of sending information over long distances wirelessly using digital signals is "the signals become weaker the farther the receiver is from the source."
Since most of the signal which we use for communication are radio signal Radio signal are basically electromagnetic waves.As the wave moves forward it looses its amplitude.So basically radio signal becomes weaker for long distance.What are radio signals?Radio signals or radio waves are a form of electromagnetic wave. Although this may sound complicated, it is possibly sufficient to say that these waves have both electric and magnetic components. They are the same as light rays, ultra-violet and infra-red. The only difference is in the wavelength of the waves.Thus , The disadvantage of sending information over long distances wirelessly using digital signals is "the signals become weaker the farther the receiver is from the source."
Learn more about Radio waves here -
https://brainly.com/question/69373
#SPJ2
how were the outer planets formed?
Answer:
All planets including the outer larger planets were formed at the same time somewhere around 4.5 Billion years ago.
Explanation:
the young sun drove away most of the gas from the inner solar system, leaving behind the rocky cores also known as the terrestrial planets.
A 100 W engine generates 1000 J of energy. How long did it run for?
A. 1 s
B. 10 s
C. 5 s
D. 100 s
Answer:
B. 10 s
Explanation:
Given the following data;
Power = 100 Watts
Energy = 1000 Joules
To find the time;
Power can be defined as the energy required to do work per unit time.
Mathematically, it is given by the formula;
[tex] Power = \frac {Energy}{time} [/tex]
Making time the subject of formula, we have;
[tex] Time = \frac {Energy}{Power} [/tex]
Substituting into the formula, we have;
[tex] Time = \frac {1000}{100} [/tex]
Time = 10 seconds
PLEASE HELP!
what would the answer be?
Answer:
Tie aluminium foil on each end of the battery using rubber band, then use copper wire to attach the led to the aluminium foil...... probably would work
Select the correct answer.
In general, how does an increase in distance from the Sun affect a planet?
ОА. .
The amount of sunlight the planet receives decreases.
OB.
The gravitational force exerted by the Sun increases.
ОС.
The thickness of a planet's atmosphere increases.
OD. The planet's atmosphere absorbs more heat.
Answer:
a.
gravity decreases by distance
thickness doesn't change
Less heat.
)) What do these two changes have in common?
mixing chocolate syrup into milk
rain forming in a cloud
) Select all that apply.
Both involve chemical bonds breaking.
Both are changes of state.
Both are only physical changes.
Both are chemical changes.
Answer:
Both are only physical changes
Explanation:
A physical change is a change that does not involve or alter the chemical composition of the substances involved. Physical changes form no new substance and can be easily separated into individual constituents. Example of physical changes are change in state, boiling, melting etc.
According to this question, two processes were given as follows:
1. mixing chocolate syrup into milk
2. rain forming in a cloud
These two processes are similar in the sense that they are both examples of physical changes.
A typical laboratory centrifuge rotates at 4000 rpm. Testtubes have to be placed into a centrifuge very carefully because ofthe very large accelerations.
Part A) What is the acceleration at the end of a test tubethat is 10 cm from the axis of rotation?
Part B) For comparison, what is the magnitude of theacceleration a test tube would experience if dropped from a heightof 1.0 m and stopped in a 1.0-ms-long encounter with a hardfloor?
Answer:
A) a_c = 1.75 10⁴ m / s², B) a = 4.43 10³ m / s²
Explanation:
Part A) The relation of the test tube is centripetal
a_c = v² / r
the angular and linear variables are related
v = w r
we substitute
a_c = w² r
let's reduce the magnitudes to the SI system
w = 4000 rpm (2pi rad / 1 rev) (1 min / 60s) = 418.88 rad / s
r = 1 cm (1 m / 100 cm) = 0.10 m
let's calculate
a_c = 418.88² 0.1
a_c = 1.75 10⁴ m / s²
part B) for this part let's use kinematics relations, let's start looking for the velocity just when we hit the floor
as part of rest the initial velocity is zero and on the floor the height is zero
v² = v₀² - 2g (y- y₀)
v² = 0 - 2 9.8 (0 + 1)
v =√19.6
v = -4.427 m / s
now let's look for the applied steel to stop the test tube
v_f = v + a t
0 = v + at
a = -v / t
a = 4.427 / 0.001
a = 4.43 10³ m / s²
Two long, straight wires are parallel and 20 cm apart. One carries a current of 2.2 A, the other a current of 5.9 A. (a) If the two currents flow in opposite directions, what is the magnitude (in N/m) and direction of the force per unit length of one wire on the other
Answer: [tex]1.298\times 10^{-5}\ N/m[/tex]
Explanation:
Given
Current in the first wire [tex]I_1=2.2\ A[/tex]
Current in the second wire [tex]I_2=5.9\ A[/tex]
wires are [tex]20\ cm[/tex] apart
Force per unit length between the current-carrying wires is
[tex]\Rightarrow \dfrac{F}{l}=\dfrac{\mu_oI_1I_2}{2\pi r}[/tex]
Force exerted by the wires is the same
Put the values
[tex]\Rightarrow \frac{F}{l}=f=\dfrac{4\pi \times 10^{-7}\times 2.2\times 5.9}{2\pi \times 0.2}=1.298\times 10^{-5}\ N/m[/tex]
This force will be repulsive in nature as the current is flowing opposite
Evaluate for f(-4)
F(x) =3x2 -5 +7
Answer: -4f=8
Explanation:
A 2000-kg elevator is at rest when its cable breaks. The elevator falls 26 m before it encounters a giant spring at the bottom of the elevator shaft. As the elevator falls, its safety clamp applies a constant frictional force of 17,000 N. 1. List all the forces acting on the elevator after the cable breaks but before it hits the spring. Determine the work done by each force on the elevator. Make sure these work terms have the appropriate signs (positive or negative). 2. Calculate the net work done on the elevator. 3. Use the work-kinetic-energy theorem to determine the speed of the elevator right before it encounters the spring. 4. After the elevator encounters the spring, the spring compresses by 0.6 m before the elevator comes to rest. The safety clamp continues to apply a constant 17,000 N force. List all the forces acting on the elevator while it falls this final 0.6 m. 5. For each force listed in question F4, determine an expression for the work it does on the elevator. Make sure each work term has the appropriate sign (positive or negative). 6. Use the work-kinetic-energy theorem to determine the value of the spring constant k.
Explanation:
work done =force *distance
work done =17000*26
work done=442,000 joules.
A 40.0 kg block of lead is heated from -25°C to 200°C.
How much heat is absorbed by the lead block?
A. 2,354,000 J
B. 1,170,000 J
C. 56,891 J
D. 10,650 J
Answer:
B. 1,170,000 J
Explanation:
Given;
mass of lead block, m = 40 kg
initial temperature, t₁ = -25 ⁰C
final temperature, t₂ = 200 ⁰C
The heat absorbed the lead block is calculated as;
H = mcΔt
where;
c is the specific heat capacity of lead = 130 J/kg⁰C
H = 40 x 130 x (200 - (-25))
H = 40 x 130 x (200 + 25)
H = 40 x 130 x 225
H = 1,170,000 J
Therefore, the heat absorbed the lead block is 1,170,000 J
A continental polar air mass forms in
a. the Pacific Ocean.
b. northern Canada.
c.
the Gulf of Mexico.
the desert Southwest.
d.
Please select the best answer from the choices provided
А
B
ОООО
С
SnnsbblHShhssbx bdBBB B BBDDBDBX Z .
my uq xbbbnxnjjxjxusjhhhwhhhnn he c x. Yes suhsjjdhhehy yes eirui
M I was going ask m
Iqijjm.ndjbh
Answer:
B. Northern Canada
Explanation:
A continental polar air mass can form over the land during the winter months. In the Northern Hemisphere, it originates in northern Canada or Alaska. As it moves southward, it brings dry weather conditions to the United States. Temperature and humidity levels are both low. Hope this helps :)
A researcher plans to release a weather balloon from ground level, to be used for high-altitude atmospheric measurements. The balloon is spherical, with a radius of 2.00 m, and filled with hydrogen. The total mass of the balloon (including the hydrogen within it) and the instruments it carries is 20.0 kg. The density of air at ground level is 1.29 kg/m3. (a) What is the magnitude of the buoyant force (in N) acting on the balloon, just after it is released from ground level
Answer:
B = 423.64 N
Explanation:
The thrust force in a fluid is equal to the weight of the displaced fluid,
B = ρ g V
where the density is that of air ρ=1.29 kg / m³ and the volume of the spherical balloon is
V = [tex]\frac{4}{3} \pi r^3[/tex]
v = 4/3 π 2³
V = 33.51 m³
let's calculate the thrust
B = 1.29 9.8 33.51
B = 423.64 N
explain why radiation is dangerous for humans
Answer:
because it affects the attom in living things
Sound waves rely on matter to transmit their energy. They cannot ravel in a vacuum. True or false
Answer:
false
Explanation:
Hello,
QUESTION)True,Sound travels in a material medium, in space, there is no matter, so sound cannot propagate.
why do the stars rotate
Answer:
Angular momentum
Explanation:
Stars are formed as a result of a collapse of a low-temperature cloud of gas and dust. During the colapse conservation of angular momentum causes any small net rotation of the cloud to increase thus forcing the material into rotating
In terms of their location, what is the difference between subcutaneous fat and visceral fat
1. Is it possible for the ball to move so quickly that the angle between the cable and vertical post stays at ninety degrees?
2. When the ball is moving in a horizontal circle, what vertical force (or component) balances gravity?
3. What happens to the centripetal force as the length of the cord increases?
Answer:
Tetherball is an interesting game in which two players tries to hit the ball hard so that it goes around the
pole.Each time the player hits the ball, it's orbit rises higher off the ground.Let's understand the physics
behind this.The motion of a tetherball is governed by two forces.These two forces combine to generate a
net force, i.e. centripetal force.If the ball is moving more quickly, it requires a greater centripetal force,
which in turn requires a greater tension force.Since the ball's weight hasn't changed, the angle of the
tension force changes until the ball is in vertical equilibrium.
To access this physics simulation visit: http://goo.gl/xVdwgO Page 02Exploration Series www.ck12.org
Ball Mass : This slider controls the mass of the ball. A ball with more mass will have more inertia, requiring
a greater net force to accelerate it. A ball with more mass will ALSO have a greater gravitational force
acting on it. Watch both of these effects occur when you manipulate this slider.
Cable Length : This slider controls the length of the cable. A longer cable is capable of allowing a greater
circular radius of motion for the ball. It is important to remember that the radius of the circular motion is
NOT equal to the length of the cable. Instead, if you want to understand the size of the circle of the ball's
motion, ignore the cable and just imagine the path of the ball.
Ball Speed : This slider controls the speed of the ball - imagine a kid just hit the ball and it sped up. A ball
moving more quickly is also accelerating more quickly because its velocity is changing as it moves in a
circle (remember that changes in DIRECTION of velocity 'count' as changes to velocity).
Force Diagram : This allows you to turn on or off the diagram of the forces acting on the ball. Look for the
ball to be in vertical force balance, which means the vertical component of tension is canceled by the
gravitational force. The ball should NOT be in horizontal force balance - it is accelerating towards the center
of the circle! It is important to note that this free body diagram should really be moving with the ball so that
To access this physics simulation visit: http://goo.gl/xVdwgO Page 03Exploration Series www.ck12.org
the tension force always points along the cord - we are just showing the forces at the moment the ball is at
the furthest-right on this screen.
Centripetal force vs Tetherball speed : This is a plot of centripetal force required to keep the ball in
circular orbit about the pole as a function of its speed. As expected, a more quickly-moving ball is changing
in velocity more often in a given amount of time, and so is accelerating more. This greater (centripetal, or
center-pointing) acceleration requires a greater net force.
Explanation:
HELP PLEASE DUE IN 3 MINUTES
Answer:
Tectonic Plate Movement
Explanation:
Each continent and ocean sits on its own tectonic plate which floats on the Earths upper mantle. They move very little over time.
Answer:
tectonic plates movement