Answer:
5 blocks east. His total distance is 15 feet.
Explanation:
I hope that this helps! Have a good day!
Radio station KBOB broadcasts at a frequency of 85.7 MHz on your dial using radio waves that travel at 3.00 × 108 m/s. Since most of the station's audience is due south of the transmitter, the managers of KBOB don't want to waste any energy broadcasting to the east and west. They decide to build two towers, transmitting in phase at exactly the same frequency, aligned on an east-west axis. For engineering reasons, the two towers must be AT LEAST 10.0 m apart. What is the shortest distance between the towers that will eliminate all broadcast power to the east and west?
Answer:
12.5 m
Explanation:
The first thing we would do is to calculate the wavelength. To do this, we use the formula
v = fλ, where
v = wave speed
f = frequency
λ = wavelength
If we make wavelength the formula, we have
wavelength = speed / frequency
Now, we substitute the values we had been given and we have
wavelength = (3 * 10^8 m/s) / (85.7 * 10^6 Hz) wavelength = 3.50 m
half of this said wavelength will be
= 3.50 / 2
= 1.75 m
As a result of the engineering constraints with the towers being more than 10 m apart, the distance can't be 1.75 m and as such, it has to be a multiple of 1.75m. So we say,
(10 / 1.75) = 5.7
So the separation will have to be 7 half wavelengths
= (7 * 1.75) = 12.5 m
When driving at slower speeds you need to use what type of steering
wheel movements compared to when driving at faster speeds? *
Answer:
slower speeds = larger and faster steering wheel movements
faster speeds = small and slow steering wheel movements
Explanation:
When driving at slower speeds you need to use larger and faster steering wheel movements. This is because at slow speeds the car does not have enough momentum to make certain maneuvers with small steering wheel movements in a given amount of time, therefore making large and faster steering wheel movements gives the car enough time with the momentum it has to make the desired maneuver. At faster speeds only small and slow steering wheel movements are needed and while cause the car to quickly change to the desired direction due to the increased momentum of the car.
for an emitted wavelength of 500 nanometers and a redshift of 0.4 what will be the observed wavelength g
Answer:
The observed wavelength is [tex] \lambda = 700nm[/tex] (color - Red)
Explanation:
From the question we are told that
The wavelength of the emitter is [tex]\lambda_ e = 500 nm = 500 *10^{-9} \ m[/tex]
The redshift is R = 0.4
Generally red shift is mathematically represented as
[tex]R = \frac{ \lambda - \lambda_e }{\lambda_e}[/tex]
=> [tex]0.4 = \frac{ \lambda - 500 *10^{-9} }{500 *10^{-9} }[/tex]
=> [tex] \lambda - 500*10^{-9} = 200*10^{-9} [/tex]
=> [tex] \lambda = 700 *10^{-9}[/tex]
=> [tex] \lambda = 700nm[/tex]
Is it true or false that the displacement always equals the product of the average velocity and the time interval?
Answer:
True.
Explanation:
Applying the definition of average velocity, we know that we can always write the following expression:[tex]v_{avg} = \frac{\Delta x}{\Delta t}[/tex] (1)
By definition, Δx is just the displacement, and Δt is the time interval.So, just rearranging terms in (1), we get:[tex]\Delta x} = v_{avg}* {\Delta t}[/tex]
use the hubble's law to determine the distance to a quasar receding at 75% the speed of light. The speed of light is 300,000 km/sec. assume Hubble's constant is
Complete question:
use the hubble's law to determine the distance to a quasar receding at 75% the speed of light. The speed of light is 300,000 km/sec. assume Hubble's constant is 2.2 x 10⁻⁵ km/s/Lyr
Answer:
The distance to the quasar is 1.02 x 10¹⁰ Lyr
Explanation:
Given;
speed of light, v = 300, 000 km/sec
Hubble's constant, H₀ = 2.2 x 10⁻⁵ km/s/Lyr
percentage of the quasar recession = 75% of speed of light
Hubble's Law is given by;
[tex]v =H_od\\\\d = \frac{v}{H_o}\\\\d= \frac{(0.75*300,000)}{2.2*10^{-5}}.Lyr\\\\d = 1.02*10^{10} \ Lyr[/tex]
Therefore, the distance to the quasar is 1.02 x 10¹⁰ Lyr
A motorcyclist goes around an un-banked (i.e., flat) circular turn of radius 31m, at a constant speed of 110km/hr (convert this to m/s). What is the minimum coefficient of static friction needed to keep the tires from slipping? Explain why the answer is (or is not) plausible.
Answer:
[tex]\mu_{s} = 3.071[/tex]
This result represents an absurd, not plausible, as coefficient of frictions from materials have values between 0 and 1.
Explanation:
From Second Newton's Law we understand that centripetal acceleration experimented by motocyclist is due to force derived from static friction. And normal force of the ground on motocyclist equals weight of motocyclist due to the flatness of circular turn. The equations of equilibrium of the motocyclist is:
[tex]\Sigma F_{x} = \mu_{s}\cdot N = m\cdot \frac{v^{2}}{R}[/tex] (Eq. 1)
[tex]\Sigma F_{y} = N-m\cdot g = 0[/tex] (Eq. 2)
Where:
[tex]\mu_{s}[/tex] - Static coefficient of friction, dimensionless.
[tex]N[/tex] - Normal force, measured in newtons.
[tex]m[/tex] - Mass of the motocyclist, measured in kilograms.
[tex]g[/tex] - Gravitational acceleration, measured in meters per square second.
[tex]v[/tex] - Speed of the motorcyclist, measured in meters per second.
[tex]R[/tex] - Radius of the circular turn, measured in meters.
The static coefficient of friction is cleared in (Eq. 1):
[tex]\mu_{s} = \frac{m\cdot v^{2}}{N\cdot R}[/tex]
From (Eq. 2) we get that normai force is:
[tex]N = m\cdot g[/tex]
And we expand the resulting expression in (Eq. 1):
[tex]\mu_{s} = \frac{m\cdot v^{2}}{m\cdot g\cdot R}[/tex]
[tex]\mu_{s} = \frac{v^{2}}{g\cdot R}[/tex] (Eq. 3)
If we know that [tex]v = 30.556\,\frac{m}{s}[/tex], [tex]g = 9.807\,\frac{m}{s^{2}}[/tex] and [tex]R = 31\,m[/tex], the expected static coefficient of friction is:
[tex]\mu_{s} = \frac{\left(30.556\,\frac{m}{s} \right)^{2}}{\left(9.807\,\frac{m}{s^{2}} \right)\cdot (31\,m)}[/tex]
[tex]\mu_{s} = 3.071[/tex]
This result represents an absurd, not plausible, as coefficient of frictions from materials have values between 0 and 1.
A man with a mass of 86.5 kg stands up in a 61-kg canoe of length 4.00 m floating on water. He walks from a point 0.75 m from the back of the canoe to a point 0.75 m from the front of the canoe. Assume negligible friction between the canoe and the water. How far does the canoe move?
Answer:
The displacement of the canoe is 1.46 m
Explanation:
Given that,
Mass of canoe = 61 kg
Mass of man = 86.5 kg
Length = 4 m
Let the the displacement of the canoe is x'
We need to calculate the displacement of the man
Using formula of displacement
[tex]x=x_{2}-x_{1}[/tex]
Put the value into the formula
[tex]x=4-(0.75+0.75)[/tex]
[tex]x=2.5\ m[/tex]
We need to calculate the displacement of the canoe
Using conservation of momentum
[tex]M_{m}v_{m}=(M_{c}+M_{m})v_{c}[/tex]
[tex]M_{m}\dfrac{x}{t}=(M_{c}+M_{m})\dfrac{x'}{t}[/tex]
[tex]86.5\times2.5=(61+86.5)\times x'[/tex]
[tex]x'=\dfrac{86.5\times2.5}{61+86.5}[/tex]
[tex]x'=1.46\ m[/tex]
Hence, The displacement of the canoe is 1.46 m
A ball of mass m is found to have a weight Wx on Planet X. Which of the following is a correct expression for the gravitational field strength of Planet X?
A. The gravitational field strength of Planet X is mg.
B. The gravitational field strength of Planet X is Wx/m.
C. The gravitational field strength of Planet X is 9.8 N/kg.
D. The gravitational field strength of Planet X is mWx.
Answer: B. The gravitational field strength of Planet X is Wx/m.
Explanation:
Weight is a force, and as we know by the second Newton's law:
F = m*a
Force equals mass times acceleration.
Then if the weight is:
Wx, and the mass is m, we have the equation:
Wx = m*a
Where in this case, a is the gravitational field strength.
Then, isolating a in that equation we get:
Wx/m = a
Then the correct option is:
B. The gravitational field strength of Planet X is Wx/m.
How do compounds differ from mixtures such as lemonade
Answer:
A mixture is a combination of two or more substances in any proportion. This is different from a compound, which consists of substances in fixed proportions. ... The lemonade pictured above is a mixture because it doesn't have fixed proportions of ingredients.
Explanation:
a. In one short sentence, explain why we call the force of gravity an attractive force.
b. Does a force of gravity exist between any two objects
Answer:
Explanation:
(a) The force of gravity is called an attractive force because it is the force (although weak) in which a planetary body or matter uses to attract an object towards itself.
(b) Yes, it does and the formula for force of gravity between any two object is
F = G[tex]\frac{m1m2}{r}[/tex]
where m1 and m2 are masses of the first and second object respectively
r is the distance between the center of the two masses
G is the gravitational constant
An ideal gas increases in temperature from 22°C to 42°C by two different processes. In one process, the temperature increases at constant volume, and in the other process the temperature increases at constant pressure. Which process requires more heat or are the required amount of heat same in both?
Answer:
a- More heat is required for the constant-pressure process than for the constant-volume
Explanation:
we have to solve using the thermodynamic first law. this is the heat applied to the system
dQ = dU + dW
definition of terms:
dU = change in internal energy
dW = work done
we have it that
change in internal energy dU is directly proportional to work done dW
but when we are in constant volume process, work done of the gas is zero
therefore
dQ of constant pressure is > than that of constant volume
so constant pressure process requires more heat
The process that requires more heat is the constant-pressure process than the constant-volume process.
According to the first law of thermodynamics, the heat that's applied to the system will be the addition of the change in internal energy and the work done.
In a constant-volume process, the work done on the gas is equal to zero. More heat will be required for the constant-pressure process than for the constant-volume process.
Also, it should be noted that the change in the thermal energy of the gas will be the same for the constant-pressure process and the constant-volume process.
Read related link on:
https://brainly.com/question/16951562
How many strings of length 10 over the alphabet (a, b, c, d] have at least one b somewhere in the string?
a) 310
b) 410 - 310
c) 10.4
d) 10.39
Complete Question
The complete question is shown on the first uploaded image
Answer:
The correct option is B
Explanation:
The number of alphabet is n= 4 (a , b , c , d )
Generally the total number of string of length 10 over the 4 alphabets is
[tex]N = 4^{10}[/tex]
Gnerally the number of string of length 10 that does not include b is
[tex]T = 3^{10}[/tex]
Generally the number of strings of length 10 over the 4 alphabets that have at least one alphabet b somewhere in the string is
[tex]G = N - T[/tex]
=> [tex]G = 4^{10} - 3^{10}[/tex]
See Conceptual Example 6 to review the concepts involved in this problem. A 12.0-kg monkey is hanging by one arm from a branch and swinging on a vertical circle. As an approximation, assume a radial distance of 86.4 cm is between the branch and the point where the monkey's mass is located. As the monkey swings through the lowest point on the circle, it has a speed of 1.33 m/s. Find (a) the magnitude of the centripetal force acting on the monkey and (b) the magnitude of the tension in the monkey's arm.
Answer:
(a) 24.56 N
(b) 142.28 N
Explanation:
(a)
The designation assigned to something like the net force pointed toward the middle including its circular route seems to be the centripetal force. The net stress only at lowest point constitutes of the strain throughout the arm projecting upward towards the middle as well as the weight pointed downwards either backwards from the center.
The centripetal function is generated from either scenario by Equation:
⇒ [tex]Fc = \frac{mv^2}{r}[/tex]
On putting the values, we get
⇒ [tex]=\frac{12\times 1.33^2}{0.864}[/tex]
⇒ [tex]=24.56 \ N[/tex]
(b)
Use T to denote whatever arm stress we can get at the bottom including its circle:
⇒ [tex]Fc = T - mg =\frac{ mv^2}{r}[/tex]
⇒ [tex]T = mg + Fc[/tex]
⇒ [tex]=12\times 9.81+24.56[/tex]
⇒ [tex]=142.28 \ N[/tex]
6) The magnitude of the force the Sun exerts on Uranus is 1.41 x 1021 newtons. Explain how it is possible for the Sun to exert agreater force on Uranus than Neptune exerts on Uranus.
Answer and Explanation:
TL: DR The Sun is much more massive than Neptune — more than enough to make up for the somewhat smaller distance between the two planets at the closest approach.
[The surprise in this answer (to me, a non-astronomer), is that the gap between the orbits of Neptune and Uranus is large — half the distance from Uranus to the Sun.]
The ratio of gravitational attraction of the Sun on Uranus versus Neptune on Uranus is directly proportional to the ratio of the Sun’s mass to Neptune’s and inversely proportional to the ratio of the square of the distances (let’s use the closest approach of the two planets to one another to calculate a maximum attraction).
Numbers:
Sun’s mass: 2 x 10^30 kg
Neptune’s mass: 1 x 10^26 kg
Distance of Sun to Uranus: 3 x 10^9 km
Closest approach of Uranus and Neptune: 1.5 x 10^9 km
Without doing any arithmetic, we see that even at their closest approach, Uranus and Neptune are separated by about one-half of the Uranus to Sun distance. Squaring that ratio, we see that if the Sun and Neptune had the same mass, the attraction between the Sun and Uranus would only be about 1/4 of that between the Sun and Neptune; however, the Sun has 20000 times the mass of Neptune, so the attraction between Uranus and the Sun is about 5000 times stronger than the maximum attraction between Uranus and Neptune.
The explanation of the possibility of why sun exerts a greater force on Uranus than Neptune exerts on Uranus is; because the force was calculated to be greater.
The formula for calculating the Force of Gravity between two masses is:
F = G*m₁*m₂/r²
Where;
F = force of gravity
G = gravitational constant = 6.674 × 10⁻¹¹ N•m²/kg²
m₁ = mass of the larger object
m₂ = mass of the smaller object
r = the distance between the centers of the two masses
Now, from online values, we have the following;
mass of Neptune; m₁ = 102.413 × 10²⁴ kg
mass of Uranus; m₂ = 86.813 × 10²⁴ kg
average distance between the centers of Neptune and Uranus; r = 1.62745 × 10¹² m
Thus, force exerted by Neptune on Uranus is;
F = (6.674 × 10⁻¹¹ × 102.413 × 10²⁴ × 86.813 × 10²⁴)/(1.62745 × 10¹²)²
F = 2.240 × 10¹⁷ N
We are told that the force the Sun exerts on Uranus is 1.41 the force the Sun exerts on Uranus is 1.41 × 10²¹ N.
That is greater than the force Neptune exerts on Uranus.
Read more about Force of Gravity at; https://brainly.com/question/7281908
A stone is thrown horizontally with an initial speed of 10m/s from the edge of the cliff. A stop watch measures the stone’s trajectory with time from the top of the hill to the bottom to be 6.7s. What is the height of the cliff?
Answer:
Answer and steps in the pic
1 (4 points) A 2-kg ball is moving with a constant speed of 5 m/s in a horizontal circle whose radius is 50 cm. What is the magnitude of the net force on the ball
Answer:
100 N
Explanation:
The following data were obtained from the question:
Mass (m) = 2 Kg
Velocity (v) = 5 m/s
Radius (r) = 50 cm
Force (F) =.?
Next, we shall convert 50 cm to metre (m). This can be obtained as follow:
100 cm = 1 m
Therefore,
50 cm = 50 cm × 1 m / 100 cm
50 cm = 0.5 m
Therefore, 50 cm is equivalent to 0.5 m.
Finally, we shall determine the magnitude of the net force on the ball by using the following formula:
F = mv²/r
Mass (m) = 2 Kg
Velocity (v) = 5 m/s
Radius (r) = 0.5 m
Force (F) =.?
F = mv²/r
F = 2 × 5²/ 0.5
F = 2 × 25/ 0.5
F = 50 / 0.5
F = 100 N
Therefore, the magnitude of the net force on the ball is 100 N.
The magnitude of the net force on the ball will be "100 N".
Force and speedAccording to the question,
Mass, m = 2 kg
Velocity, v = 5 m/s
Radius, r = 50 cm or,
= 50 × [tex]\frac{1}{100}[/tex]
= 0.5 m
We know the relation,
Force, F = [tex]\frac{mv^2}{r}[/tex]
By substituting the values, we get
= [tex]\frac{2\times (25)^2}{0.5}[/tex]
= [tex]\frac{2\times 25}{0.5}[/tex]
= [tex]\frac{50}{0.5}[/tex]
= 100 N
Thus the above response is appropriate.
Find out more information about force here:
https://brainly.com/question/6504879
Given that water at standard pressure freezes at 0∘C, which corresponds to 32∘F, and that it boils at 100∘C, which corresponds to 212∘F, calculate the temperature difference ΔT in degrees Fahrenheit that corresponds to a temperature difference of 1 K on the Kelvin scale. Give your answer to two significant figures.
Answer:
In two significant figure 360K
Explanation:
The temperature difference (ΔT) can be calculated as the boiling temperature minus the freezing temperature in Fahrenheit.
Hence,
ΔT = 212 - 32
ΔT = 180°F
To convert to °F to kelvin, we use the formula below
= (°F - 32) × 5/9 + 273.15
= (180°F - 32) × 5/9 + 273.15
= 355.37K ⇔ 360K
Plz help me fast WITH EXTRA POINTS AFTER SUBMITTING
Answer:
4 bobux
Explanation:
one bobux
two bobux
three bobux
four bobux
Compare the amount of thermal energy required to MELT a solid with the amount of thermal energy released when the same liquid becomes a solid.
Which is a belief held by sociologists who work from a social-conflict
perspective?
O A. The best approach for a study is from a micro-level orientation.
O B. Personal background has little impact on how individuals react
with one another.
C. Some social patterns are helpful, while others are harmful.
D. Data are irrelevant to the study of sociology.
SUBMIT
Answer:
C. Some social patterns are helpful, while others are harmful.
Explanation:
Hope this was helpful, Have an amazing,spooky Halloween!!
my heart strike him to dead.what figure of speech is that?
Answer:
Hyperbole
Explanation:
this is an extreme exaggeration or overstatement/ magnification
A cart with an unknown mass is at rest on one side of a track. A student must find the mass of the cart by using Newton’s second law. The student attaches a force probe to the cart and pulls it while keeping the force constant. A motion detector rests on the opposite end of the track to record the acceleration of the cart as it is pulled. The student uses the measured force and acceleration values and determines that the cart’s mass is 0.4kg . When placed on a balance, the cart’s mass is found to be 0.5kg . Which of the following could explain the difference in mass?
Answer choices:
A) The track was not level and was tilted slightly downward.
B) The student did not pull the cart with a force parallel to the track.
C) The wheels contain bearings that were rough and caused a significant amount of friction.
D) The motion sensor setting was incorrect. The student set it up so that motion away from the sensor would be the negative direction.
Answer: The correct answer is A) The track was not level and was tilted slightly downward.
Explanation: This is because of the two values: 0.4 kg and 0.5 kg. I won't go into much detail but due to this difference of mass, we know that the track was not level.
"The track was not level and was tilted slightly downward" could explain the difference in the mass.
Mostly because the university student or learners calculates a mass of just over the spring quantity, the vehicle speed seems to have been higher than there would have had to be.Option B, as well as Option C, are wrong because the acceleration would've been smaller in each of these 2 circumstances, so that computed mass would've been larger.
Thus Option A is appropriate.
Learn more:
https://brainly.com/question/11839345
Hollywood and video games often depict the bad guys being "blown away" when they’re shot by a bullet (i.e. once hit, their feet leave the ground and they fly backwards). Assuming that even if a handgun cartridge did generate enough momentum for the bullet to do this, why is it still nonsense on-screen?
Answer:
Taking a look at Newton's third law of motion which states "for every force exerted, their is an opposite force equal in magnitude and opposite in direction on the first force".
Similarly if a bullet had enough forces behind it to hurl someone through the air when they were hit, a similar force would act on the person holding the gun that fired the bullet.
What we load into the gun is called a 'cartridge' Each piece is composed of four basic substance the casing, the bullet, the primer, and the powder.
The primer explodes lighting the powder which causes a buildup of pressure behind the bullet. This powder can be used in rifle cartages because the bullet chamber is designed to withstand greater pressures.
It is difficult in practice to measure the forces within a gun bagel, but the one easily measured parameter is the velocity with which the bullet exits muzzle velocity, therefore assuming that even if a handgun cartridge which generate enough momentum for the bullet to do this, it is still nonsense on screen in Hollywood and video.
What is the car’s average velocity (in m/s) in interval between t=1.0s to t=1.5s?
Answer:
This question is incomplete
Explanation:
This question is incomplete. However, the formula for velocity is;
Velocity (in m/s) = distance/time
The distance the car covered in the completed question is divided by the difference in the time interval
The difference in the time interval will be = 1.5s - 1.0s = 0.5s
NOTE: the distance must be in meters or be converted to meters
The word acid comes from the Latin word
A 126 N force is applied at an angle of 25.00 to a 8.50 kg block pressed against a rough vertical wall and the block slides down the wall at constant velocity. Calculate the coefficient of kinetic friction between the block and the wall.
Answer:
μk = 0.58
Explanation:
If the block is sliding down at constant speed, this means that no net force is acting upon it in the vertical direction.As the block is pressed on the wall, this means that it doesnt accelerate in the horizontal direction either, so no net force acts upon it in this direction also.In this direction, we have only two forces acting, equal and opposite each other, one is the normal force (exerted by the wall) and the other is the horizontal component of the applied force.If the applied force forms an angle of 25º with the wall (which is vertical), this means that we can get its projection along the horizontal direction, using simple trigonometry , as follows:[tex]F_{apph} = F_{app} * sin\theta = 126 N * sin 25 = 53.3 N[/tex]
⇒ [tex]F_{n} = - F_{apph} = -53.3 N[/tex]
In the vertical direction, we have three forces acting on the block: the weight pointing downward, the kinetic friction force (as we know that the block is sliding), and the vertical component of the applied force, in the same direction as the friction one.As we have already said, the sum of these forces must be 0.[tex]F_{g} + F_{appv} + F_{ff} = 0 (1)[/tex] where Fg is the weight of the block, Fappv is the vertical component of the applied force, and Fff is the kinetic friction force.Replacing these forces by their mathematical expressions, we have:[tex]F_{g} = m_{b} * g = 8.5 Kg * (-9.8 m/s2) = -83.3 N[/tex]
[tex]F_{appv} = F_{app}* cos\theta = 126 N * cos 25 = 114.2 N[/tex]
[tex]F_{ff} = \mu_{k}* F_{n} =\mu_{k} * (-53.3 N)[/tex]
Replacing in (1), and solving for μk, we finally get:μk = 0.58
An electric drill starts from rest and rotates with a constant angular acceleration. After the drill has rotated through a certain angle, the magnitude of the centripetal acceleration of a point on the drill is 7.9 times the magnitude of the tangential acceleration. What is the angle
Answer:
The angle is 3.95 rad.
Explanation:
The angle can be calculated as follows:
[tex] \omega_{f}^{2} = \omega_{0}^{2} + 2\alpha \theta [/tex]
Where:
[tex]\omega_{f}[/tex]: is the final angular speed
ω₀: is the initial angular speed = 0 (it starts from rest)
α: is the angular acceleration
θ: is the angle=?
The centripetal acceleration is:
[tex]a_{c} = \omega_{f}^{2}*r[/tex]
And the tangential acceleration is:
[tex] a_{T} = \alpha*r [/tex]
Since the magnitude of the centripetal acceleration is 7.9 times the magnitude of the tangential acceleration:
[tex]a_{c} = 7.9a_{T}[/tex]
[tex]\omega_{f}^{2}*r = 7.9*\alpha*r \rightarrow \alpha = \frac{\omega_{f}^{2}}{7.9}[/tex]
Now, the angle is:
[tex]\omega_{f}^{2} = 2(\frac{\omega_{f}^{2}}{7.9})\theta[/tex]
[tex] \theta = \frac{7.9}{2} = 3.95 rad [/tex]
Therefore, the angle is 3.95 rad.
I hope it helps you!
The angular distance traveled by the electric drill is 3.95 radians.
The given parameters;
initial angular speed, [tex]\omega_i[/tex] = 0centripetal acceleration, [tex]a_c[/tex] = 7.9aThe angular distance traveled by the electric drill is calculated as follows;
[tex]\omega_f^2 = \omega_i^2 + 2\alpha \theta[/tex]
The relationship between centripetal acceleration, tangential acceleration and angular speed is given as;
[tex]a_c = \omega ^2 r\\\\a = \alpha r\\\\a_c = 7.9a= 7.9\alpha r\\\\7.9\alpha r = \omega^2 r\\\\\alpha = \frac{\omega ^2}{7.9}[/tex]
Substitute the value of angular acceleration into the first equation;
[tex]\omega _f^2 = 0 + 2(\a (\frac{\omega _f^2}{7.9})\theta\\\\2\theta \omega_f^2 = 7.9\omega_f ^2\\\\\theta = \frac{7.9}{2} \\\\\theta = 3.95 \ rad[/tex]
Thus, the angular distance traveled by the electric drill is 3.95 radians.
Learn more about angular distance here: https://brainly.com/question/12680957
Metals that have shine and luster?
Answer:
luster
Explanation:
Consider a 50-turn circular loop with a radius of 1.55 cm in a 0.35-T magnetic field. This coil is going to be used in a galvanometer that reads 45 μA for a full-scale deflection. Such devices use spiral springs which obey an angular form of Hooke's law, where the restoring torque is:
τs = -κ θ.
Here κ is the torque constant and θ is the angular displacement, in radians, of the spiral spring from equilibrium, where the magnetic field and the normal to the loop are parallel.
Required:
a. Calculate the maximum torque, in newton meters, on the loop when the full-scale current flows in it.
b. What is the torque constant of the spring, in newton meters per radian, that must be used in this device?
Complete Question
Consider a 50-turn circular loop with a radius of 1.55 cm in a 0.35-T magnetic field. This coil is going to be used in a galvanometer that reads 45 μA for a full-scale deflection. Such devices use spiral springs which obey an angular form of Hooke's law, where the restoring torque is:
τs = -κ θ.
Here κ is the torque constant and θ is the angular displacement, in radians, of the spiral spring from equilibrium, where the magnetic field and the normal to the loop are parallel.
Required:
a. Calculate the maximum torque, in newton meters, on the loop when the full-scale current flows in it.
b. What is the torque constant of the spring, in newton meters per radian, that must be used in this device? Assume the full scale deflection is 60° from the spring's equilibrium position
Answer:
a
[tex]\tau_{m} = 5.95 *10^{-7} \ N \cdot m[/tex]
b
[tex]\beta = 2.83 *10^{-7} \ N \cdot m / rad [/tex]
Explanation:
From the question we are told that
The number of turns is N = 50
The radius is r = 1.55 cm = 0.0155 m
The magnetic field is B = 0.35 T
The induced current is [tex]I = 45 \mu A = 45 *10^{-6} \ A[/tex]
Generally the area of loop is mathematically represented as
[tex]A = \pi r^2[/tex]
=> [tex]A =3.142 * 0.0155^2[/tex]
=> [tex]A =0.000755\ m^2[/tex]
Generally the maximum torque is mathematically represented as
[tex]\tau_{m} = N * B * I * A[/tex]
=> [tex]\tau_{m} = 50 * 0.35 * 45 *10^{-6} * 0.000755[/tex]
=> [tex]\tau_{m} = 5.95 *10^{-7} \ N \cdot m[/tex]
Generally the torque 60° from the spring's equilibrium position is mathematically represented as
[tex]\tau = N * B * I * A * sin (60)[/tex]
=> [tex]\tau = 50 * 0.35 * 45 *10^{-6} * 0.000755 * sin (60)[/tex]
=> [tex]\tau = 2.973 *10^{-7} \ N \cdot m [/tex]
Generally the toque constant of the spring is mathematically represented as
[tex]\beta = \frac{\tau}{60}[/tex]
=> [tex]\beta = \frac{\tau}{\frac{\pi}{3}}[/tex]
=> [tex]\beta = \frac{2.973 *10^{-7}}{\frac{\pi}{3}}[/tex]
=> [tex]\beta = 2.83 *10^{-7} \ N \cdot m / rad [/tex]
A 50 kg bicyclist starts his ride down the road with an acceleration of 1m/s2 in air with a density of 1.2 kg/m3. If his velocity at a given moment is 2m/s, how much force is he exerting? Assume the area of his body is 0.5m^2.
a. The bicyclist is exerting 1.1 N of force.
b. The bicyclist is exerting 49 N of force.
c. The bicyclist is exerting 50 N of force.
d. The bicyclist is exerting 51 N of force.
Answer:
b. The bicyclist is exerting 49 N of force
Explanation:
Given;
mass of bicyclist start, m = 50 kg
acceleration, a = 1 m/s²
density of air, ρ = 1.2 kg/m³
velocity, v = 2 m/s
Area of the bicyclist body, A = 0.5 m²
The drag force on the bicyclist is given by ;
Fd = 0.5CρAv²
where;
C is drag coefficient = 0.9 for bicycle
Fd = 0.5 x 0.9 x 1.2 x 0.5 x 2²
Fd = 1.1 N
The force of the bicyclist is given by;
F = ma
F = 50 x 1
F = 50 N
The effective force exerted by the bicyclist is given by;
Fe = F - Fd = 50 N - 1.1 N
Fe = 49 N
Therefore, the force exerted by the bicyclist is 49 N