Answer: Parting uses a blade-like cutting tool plunged directly into the workpiece to cut off the workpiece at a specific length. It is normally used to remove the finished end of a workpiece from the bar stock that is clamped in the chuck. Other uses include things such as cutting the head off a bolt.
Explanation:
Which option identifies the next step in the following scenario?
After being chosen to reverse engineer the inside of an older refrigerator, an engineer determines all of the product’s components.
A: The engineer will create a detailed sketch that labels all of the visual components.
B: The engineer will create an enhanced version of the product.
C: The engineer will create an isometric computer analysis of all the components.
D: The engineer will create a prototype of the product.
Answer: The engineer will create a detailed sketch that labels all of the visual components.
Explanation:
It should be noted that the reverse engineering is required for the replacement and the modification of an existing product.
With regards to the question, the correct answer is option A "The engineer will create a detailed sketch that labels all of the visual components".
Answer:
visual engineer
Explanation:
took da class
How much wil molly monthly payment be?
B be should answer The
Determine the tensile design strength for W16x89 and two connected 1/4"x12 in plates, with two lines of 7/8-in diameter bolts in each flange using A 572 Grade steel with Fy=50 ksi and Fu=65 ksi as shown in Figure. There are three bolts in each line 3-in on center. Check block shear for plate only.
Answer:
12
Explanation:
Helpppppp
The location of a vertical section through an object is shown by a(n)
_____ in the top view.
Answer:
Among us is the answer
Explanation:
If you play among is everyday then Among us is always the answer
Help I'm giving 20 points for who ever answers it
Answer:
the product design
Explanation:
i think??
help asap 9) A poorly tied down blimp falls over in a field. If the blimp exerts a downward force of 4000 N over an area
of 250 m2, what pressure is put on the ground by the blimp?
Answer:
[tex]Pressure = 16\ pa[/tex]
Explanation:
Given
[tex]Force = 4000N[/tex]
[tex]Area = 250m^2[/tex]
Required
Determine the pressure
Pressure is calculated using:
[tex]Pressure = \frac{Force}{Area}[/tex]
Substitute values for Force and Area
[tex]Pressure = \frac{4000N}{250m^2}[/tex]
[tex]Pressure = 16N/m^2[/tex]
Change units
[tex]Pressure = 16\ pa[/tex]
Which dimension of wellness focuses on finding enjoyment and satisfaction in daily endeavours?
Answer:
I believe its emotional because it says satisfaction and most of the time that has to deal with emotions running through the body.
Explanation:
help pls
7) A balle dancer does a pirouette on the tip of his toe. If the dancer has a weight of 580N and the tip of his
ballet shoe measures 0.02 mby: 0.01 whar pressure does his toe exert on the stage?
Answer:
Pressure is equal to 2900000 Newton per square m
Explanation:
The correct question is
A Ballat dancer does a pirouette on the tip of his toe if the dancer has a weight of 580 n and the tip of his ballot show measures 0.02 by 0.01 M what pressure does his to exert on the stage?
Solution
The area of the tip of the ballot show is equal to [tex]0.02 * 0.01 = 0.0002[/tex] square meter
Pressure is equal to force applied divided by the area of the contact point.
[tex]P = \frac{Force}{Area}[/tex]
Substituting the give values we get -
[tex]P = \frac{580}{0.0002} \\P = 2900000[/tex] Newton per square meter
9. Cigarette smoking is dangerous to one's health. Which of the following is the
harmful carbon compound found in cigarettes?
a. caffeine
b. morphine
c. nicotine
d. thiamine
could I please get help with this
Answer:
1.[tex]I_{xc}[/tex] = 7.161458[tex]\overline 3[/tex] in.⁴
[tex]I_{yc}[/tex] = 36.661458[tex]\overline 3[/tex] in.⁴
Iₓ = 28.6458[tex]\overline 3[/tex] in.⁴
[tex]I_y[/tex] = 138.6548[tex]\overline 3[/tex] in.⁴
2. [tex]I_{xc}[/tex] = 114.[tex]\overline 3[/tex] in.⁴
[tex]I_{yc}[/tex] = 37.[tex]\overline 3[/tex] in.⁴
Iₓ = 457.[tex]\overline 3[/tex] in.⁴
[tex]I_y[/tex] = 149.[tex]\overline 3[/tex] in.⁴
3. The maximum deflection of the beam is 2.55552 inches
Explanation:
1. The height of the beam having a rectangular cross section is h = 2.5 in.
The breadth of the beam, is = 5.5 in.
The moment of inertia of a rectangular beam through its centroid is given as follows;
[tex]I_{xc}[/tex] = b·h³/12 = 5.5 × 2.5³/12 = 1375/192 = 7.161458[tex]\overline 3[/tex]
[tex]I_{xc}[/tex] = 7.161458[tex]\overline 3[/tex] in.⁴
[tex]I_{yc}[/tex] = h·b³/12 = 2.5 × 5.5³/12 = 6655/192 = 36.661458[tex]\overline 3[/tex]
[tex]I_{yc}[/tex] = 36.661458[tex]\overline 3[/tex] in.⁴
The moment of inertia about the base is given as follows;
Iₓ = b·h³/3 = 5.5 × 2.5³/3 = 625/24 = 28.6458[tex]\overline 3[/tex]
Iₓ = 28.6458[tex]\overline 3[/tex] in.⁴
[tex]I_y[/tex] = h·b³/3 = 2.5 × 5.5³/3 = 6655/48= 138.6548[tex]\overline 3[/tex]
[tex]I_y[/tex] = 138.6548[tex]\overline 3[/tex] in.⁴
2. The height of the beam having a rectangular cross section is h = 7 in.
The breadth of the beam, b = 4 in.
The moment of inertia of a rectangular beam through its centroid is given as follows;
[tex]I_{xc}[/tex] = b·h³/12 = 4 × 7³/12 = 114.[tex]\overline 3[/tex]
[tex]I_{xc}[/tex] = 114.[tex]\overline 3[/tex] in.⁴
[tex]I_{yc}[/tex] = h·b³/12 = 7 × 4³/12 = 37.[tex]\overline 3[/tex]
[tex]I_{yc}[/tex] = 37.[tex]\overline 3[/tex] in.⁴
The moment of inertia about the base is given as follows;
Iₓ = b·h³/3 = 4 × 7³/3 = 457.[tex]\overline 3[/tex]
Iₓ = 457.[tex]\overline 3[/tex] in.⁴
[tex]I_y[/tex] = h·b³/3 = 2.5 × 5.5³/3 = 149.[tex]\overline 3[/tex]
[tex]I_y[/tex] = 149.[tex]\overline 3[/tex] in.⁴
3. The deflection, [tex]\delta _{max}[/tex], of a simply supported beam having a point load at the center is given as follows;
[tex]\delta_{max} = \dfrac{W \times L^3}{48 \times E \times I}[/tex]
The given parameters of the beam are;
The length of the beam, L = 22 ft. = 264 in.
The applied load at the center, W = 750 lbs
The modulus of elasticity for Cedar = 10,000,000 psi
The height of the wood, h = 3 in.
The breadth of the wood, b = 5 in.
The moment of inertia of the wood, [tex]I_{xc}[/tex] = b·h³/12 = 5 × 3³/12 = 11.25 in.⁴
By plugging in the given values, we have;
[tex]\delta_{max} = \dfrac{750 \times 264^3}{48 \times 10,000,000 \times 11.25} = 2.55552[/tex]
The maximum deflection of the beam, [tex]\delta _{max}[/tex] = 2.55552 inches
What does an engineer do? List as many types of engineers as you can.
Answer:
Mechanical Engineering
Chemical Engineering
Civil Engineering
Explanation:
I got it from my old homework And I learn those at school ( Thank You For The Points)
Name two problems that can happen after a phone or gaming system updates
Recall the steps of the engineering design process. Compare and contrast the
similarities and differences between the stages of the web design process and the
engineering design process.
Answer:
hi
Explanation:
hiiiiiiiiiiiiiiiiiiiiiiiii
How many junctions are in a typical house
Explanation:
there are no limits of the number of junction boxes in any particular circuit.
Pls answer ASAP 7. A GOOD SAFETY RULE, WHEN YOU ARE SURE YOU HAVE A LEGAL RIGHT-OF-
WAY, IS:
A. Always take it
B. Never insist on it
C. Always let the other driver have
Answer:
A
Explanation:
I don`t know I need points hope it was correct.
A good safety rule, when you are sure you have a legal right of way is: B. Never insist on it.
What is safety rule?Even if you are certain that you have a legal right-of-way, it is still crucial to put safety first and avoid being overly insistent on it. When driving, safety should always come first, even if you have the right-of-way legally.
Being cautious and courteous while driving are essential components of defensive driving, and this includes letting other drivers go ahead of you if doing so will help you avoid potential collisions or problems.
Therefore the correct option is B.
Learn more about safety rule here:https://brainly.com/question/29789032
#SPJ4