The best way to explain the difference is ''Jitter is the up and down variation in latency''.
Explain the difference between latency and jitter ?The main difference between jitter and latency is that jitter is defined as a shift in the amount of latency, whereas latency is defined as a delay caused by the network. It's crucial to frequently check jitter and delay since they have a detrimental effect on network performance.Jitter should ideally be less than 30ms. Network latency shouldn't exceed 150 ms one-way, and packet loss shouldn't be more than 1%.In a nutshell, jitter is an unintentional increase in latency or ping rate. When the rate fluctuates, it shakes the signal and increases the ping rate or latency on the way to and from the server, slowing down signal transmission and possibly leading to data loss. This is known as jitter.Learn more about latency and jitter refer to :
https://brainly.com/question/13010901
#SPJ1
in preparation to use your notebook on the airplane as you travel to a conference, you disconnected the external usb mouse. the cursor drifts consistently to the left side of the screen while using the built-in trackpad and mouse buttons on the notebook. which of the following actions would most likely stop the mouse from drifting? answer buy a new external mouse. update the trackpad drivers. enable airplane mode. disable the trackpad in the control panel.
Access the BIOS/UEFI configuration and disable the USB pointer option.
What is BIOS?
The term "BIOS" stands for "basic input-output system." It is low-level software that is housed in a chip on the motherboard of your computer. When your computer turns on, the BIOS loads and is in charge of waking up the hardware components, checking that they are operating properly before launching the bootloader, which boots Windows or any other operating system you may have installed.
What is the difference between UEFI and BIOS?
Drive sizes up to 9 zettabytes are supported by UEFI, compared to just 2.2 terabytes by BIOS. A quicker boot time is offered by UEFI. While BIOS has drive support stored in its ROM, UEFI has discrete driver support. As a result, updating BIOS firmware can be challenging.
What is mean by a configuration?
A configuration is typically the arrangement of the parts that make up a whole, or the process of doing so.
To know more about UEFI and BIOS, check out:
https://brainly.com/question/28485802
#SPJ1
Disable the USB pointer setting in the BIOS/UEFI configuration.
What is configuration?
The definition of configuration in the context of computers and technology is the organisation of the IT system's hardware and software. You have more control so over devices in your network thanks to management of a components, settings, and other factors that guarantee smooth operation of all IT systems. Two of the main issues surrounding the requirement for a configured properly technology infrastructure are function and performance. Along with the security and safety of your company's data, reliability is a factor. Devices that are initially configured correctly can spare you trouble in future technology audits.
To learn more about configuration
https://brainly.com/question/29415808
#SPJ1
let tree be an arraylist instance and assume that tree.tostring() evaluates to [birch, oak, elm, maple]. what does tree.tostring() evaluate to after the statement tree.remove(2);?
[birch, oak]
[birch, elm, maple]
[birch, oak, maple]
[elm, maple]
The tree.tostring() evaluate to after the statement tree. remove(2); is [birch, oak]. The correct option is A.
What is an Array List instance?Java's Array List is used to hold collections of elements that change in size dynamically. An Array List automatically expands in size when new elements are added to it, unlike Arrays, which have a fixed size. Java's collection foundation includes Array List, which implements the List interface.
A comma-separated set of constant expressions encased in braces () serves as an array's initializer. An equal sign (=) is placed in front of the initializer. Not every element in an array needs to be initialised.
Therefore, the correct option is A, [birch, oak].
To learn more about ArrayList instance, refer to the link:
https://brainly.com/question/20039207
#SPJ1
besides the motherboard's size, what other characteristic determines whether the motherboard will fit well inside a particular case?
Besides the motherboard's size, the Locations of screw holes determines whether the motherboard will fit well inside a particular case.
What is a Motherboard?
It is also known as the mb, mainboard, mboard, mobo, mobd, backplane board, base board, main circuit board, planar board, system board, or a logic board.
The motherboard is the largest board in a computer chassis and is a printed circuit board and the foundation of a computer. It manages power and communicates with the CPU, RAM, and all other computer hardware components.
What is the main function of the motherboard?
The primary function of your motherboard is to support all of the components that comprise your computer. When compared to the human body, the motherboard is the backbone, nervous system, and circulatory system all rolled into one.
It physically supports various components, similar to a backbone, functions as a control center, similar to a nervous system, and moves voltage, similar to a circulatory system. For a more geeky analogy, the motherboard is the black lion from Voltron, serving as the torso that connects all the other parts.
To know more about motherboard, visit: https://brainly.com/question/11179147?referrer=searchResults
#SPJ4
what transition documentation component is meant to assist local service providers in surmounting developing challenges?
Note that the transition documentation component is meant to assist local service providers in surmounting developing challenges is "expected future problems"
What is Transition Documentation?A transition plan details your present tasks and responsibilities to teach your successor how to execute your work properly and to assist you to move out of your position seamlessly.
A transition plan outlines your usual activities and responsibilities, as well as current projects, forthcoming deadlines, and essential contacts.
The goal of transition evaluations is to advise young people and their families about what to expect in the future so that they can prepare for adulthood. Transition evaluations should take place at the appropriate moment for the young person or caregiver to reach their goal.
Learn more about Transition Documentation:
https://brainly.com/question/1862731
#SPJ1
Write a query to display the book number, title, and number of times each book has been checked out. Limit the results to books that have been checked out more than 5 times. Sort the results in descending order by the number of times checked out, and then by title. (Figure P8.57)
Chapter 8 problem 57. Problem taken from Database Systems: Design, Implementation, and Management, 12th edition, by Carlos Coronel and Steven Morris
The query to display the book number, title, and number of times each book has been checked out is Choose "Book Title," "Book Cost," and "Book Year From Book Order";.
A search for information or a question is what a query is. The phrases inquiry, question, quest, request, and query all derive from the Latin verb quaere, which meaning "to ask." When discussing Internet searches, courteous professional conversation, and delicate requests, the word "query" typically fits the bill.
A query might ask your database for data results, a specific action to be taken with the data, or both. A query can add, change, or remove data from a database, perform calculations, combine data from various tables, and answer simple questions.
To know more about database click here:
https://brainly.com/question/29412324
#SPJ4
i. weak passwords ii. inappropriate use of the internet iii. inappropriate use of e-mail iv. divulging confidential information the above items typically constitute employee security violations.
Weak passwords, inappropriate use of the internet, inappropriate use of e-mail, and divulging confidential information, these mention items typically constitute employee security policy violations.
Violation of employee policies can cause harm to the employees themselves. Losses obtained include misuse of employee personal data. The company should be responsible for maintaining the personal data of its employees. As for employees, you should not give the password regarding your personal account to other people, including the company. A policy violation occur when a user records an expense with details violating the company's policies.
Learn more about policy violations, here https://brainly.com/question/11566483
#SPJ4
With respect to iot security, what term is used to describe the digital and physical vulnerabilities of the iot hardware and software environment?.
Option C is correct. Unsecured communications are one of the main hazards posed by the Internet of Things. Data communications between devices are vulnerable to third-party interception.
Threat actors might be able to obtain sensitive data like user passwords or credit card numbers as a result of this. insufficient computing power for effective built-in security. IoT system access control is inadequate. Budget constraints prevent properly testing and enhancing firmware security. Due to IoT device technological restrictions and budgetary constraints, there aren't any regular patches or upgrades. Cybercriminals can use IoT vulnerabilities as a starting point to get over firewalls, access private networks, and steal sensitive data as it moves between linked device environments. Cyberattacks can spread to other networked systems due to the risk associated with these compromised devices.
Learn more about communication here-
https://brainly.com/question/14809617
#SPJ4
Jerry has a problem with a package he just received—two items from his order are missing. Who should he contact to resolve the problem?.
Jerry can contact customer service repsentative in the delivery service that he used. Customer service will help to solve your problem.
Customer service refers to the assistance and advice provided by a company to those people who buy or use its products or services. Customer service has jobdesc to help and handle the complain the customer that used a company product. If you have problem with the package, service or product of company, you can complain it, and the customer service will help you to solve it. It's free as far as the problem of the product is caused by damage of delivery service. You're able to respond quickly and effectively, resulting in a positive customer experience.
Learn more about Customer service, here https://brainly.com/question/13540066
#SPJ4
Selected molecular descriptors from the Dragon chemoinformatics application were used to predict bioconcentration factors for 779 chemicals in order to evaluate QSAR (Quantitative Structure Activity Relationship). This dataset was obtained from the UCI machine learning repository.
The dataset consists of 779 observations of 10 attributes. Below is a brief description of each feature and the response variable (logBCF) in our dataset:
nHM - number of heavy atoms (integer)
piPC09 - molecular multiple path count (numeric)
PCD - difference between multiple path count and path count (numeric)
X2Av - average valence connectivity (numeric)
MLOGP - Moriguchi octanol-water partition coefficient (numeric)
ON1V - overall modified Zagreb index by valence vertex degrees (numeric)
N.072 - Frequency of RCO-N< / >N-X=X fragments (integer)
B02[C-N] - Presence/Absence of C-N atom pairs (binary)
F04[C-O] - Frequency of C-O atom pairs (integer)
logBCF - Bioconcentration Factor in log units (numeric)
Note that all predictors with the exception of B02[C-N] are quantitative. For the purpose of this assignment, DO NOT CONVERT B02[C-N] to factor. Leave the data in its original format - numeric in R.
Please load the dataset "Bio_pred" and then split the dataset into a train and test set in a 80:20 ratio. Use the training set to build the models in Questions 1-6. Use the test set to help evaluate model performance in Question 7. Please make sure that you are using R version 3.6.X or above (i.e. version 4.X is also acceptable).
The coding solution for the given problem is provided below, in which we must select molecular descriptors from the Dragon chemoinformatics application to predict bioconcentration factors for 779 chemicals in order to evaluate QSAR (Quantitative Structure Activity Relationship).
Coding Part:
# Clear variables in memory
rm(list=ls())
# Import the libraries
library(CombMSC)
library(boot)
library(leaps)
library(MASS)
library(glmnet)
# Ensure that the sampling type is correct
RNGkind(sample.kind="Rejection")
# Set a seed for reproducibility
set.seed(100)
# Read data
fullData = read.csv("~/Documents/ISYE6414/Bio_pred.csv",header=TRUE)
# Split data for traIning and testing
testRows = sample(nrow(fullData),0.2*nrow(fullData))
testData = fullData[testRows, ]
trainData = fullData[-testRows, ]
To know more about variables in memory, visit: https://brainly.com/question/29358320
#SPJ4
which type of presentation will likely include many slides created in a program like microsoft powerpoint?
Formal type of presentations are included in Microsoft Powerpoint.
What is Microsoft Powerpoint?It is a presentation-based program that makes a presentation more interactive and interesting by using graphics, videos, and other media. A saved Powerpoint presentation has the file extension ".ppt." PPT is another name for a PowerPoint presentation that includes slides and other features.PowerPoint gives you complete control over the appearance of your slides. You are free to personalize your presentation with your own design. Because the elements provided by this software are simple to modify and play with, you can create the ideal presentation for yourself.PowerPoint's tools include Home, File, Insert, Design, Animations, Transitions, Slide Show, Review, and View.PowerPoint slides can be divided into three categories, each of which can exist in isolation or in combination with others: Text slides. Conceptual slides. Quantitative charts.To learn more about Microsoft Powerpoint refer to :
https://brainly.com/question/23714390
#SPJ4
Formal type of presentations are included in Microsoft PowerPoint.
What is Microsoft Powerpoint?It is a presentation-based program that makes a presentation more interactive and interesting by using graphics, videos, and other media. A saved PowerPoint presentation has the file extension ".ppt." PPT is another name for a PowerPoint presentation that includes slides and other features.PowerPoint gives you complete control over the appearance of your slides. You are free to personalize your presentation with your own design. Because the elements provided by this software are simple to modify and play with, you can create the ideal presentation for yourself.PowerPoint's tools include Home, File, Insert, Design, Animations, Transitions, Slide Show, Review, and View.PowerPoint slides can be divided into three categories, each of which can exist in isolation or in combination with others: Text slides. Conceptual slides. Quantitative charts.To learn more about Microsoft PowerPoint refer to :
https://brainly.com/question/19250114
#SPJ4
imwrite. write a new image that is similar to the image matrix a, % except that the values should be a third as bright. the name of the new % image is stored in the variable img2.
img2 = a/3; By dividing the original image matrix 'a' by a value of 3, we can create a new image matrix 'img2' which is similar to the original but with all of the values a third as bright.
The name of the new % image is stored in the variable img2?img2 = a/3The new image matrix stored in the variable 'img2' is created by taking the original image matrix 'a' and dividing all of the values by a third. This results in a new image matrix which is similar to the original, except that the values are a third as bright. This can be used to create a darker or more subtle version of the original image.
Learn more about Programming: https://brainly.com/question/16397886
#SPJ4
What is the output of this program? Assume the user enters 3, 6, and 11.
numA = 0
for count in range(3):
answer = input ("Enter a number: ")
fltAnswer = float(answer)
numA = numA + fltAnswer
print (numA)
Output:
Answer:
Output: 23.0
Explanation:
1) numA += 3; (3)
2) numA += 9 (12) #3 + 9 = 12
3) numA += 11 (23) #12 + 11 = 23
float(23) = 23.0
Answer: 20
Explanation:
it is a basic python code
fitAnswer intoduses loop into the given variable
==> intial A=[0]
after addind 3
A=[0,3]=0+3=3
A=[0,3,6]=0+3+6=9
A=[0,3,6,11]=0+3+6+11=20
Which two statements describe ways that engineers using the engineering design process can benefit from the use of computer models?
a. computer models can aid engineers in presenting and sharing ideas about ways to solve design problems.
b. computer models can eliminate the need to make prototypes by representing every aspect of the real world.
c. computer models can take the place of the engineering design process by predicting the best possible design.
d. computer models can help engineers simulate designs that are too dangerous or expensive to test in real life.
The two statements that describe ways that engineers using the engineering design process can benefit from the use of computer models are options A and C:
a. Computer models can aid engineers in presenting and sharing ideas about ways to solve design problems.
c. Computer models can take the place of the engineering design process by predicting the best possible design.
What advantages do engineers have when employing the design process?A person can come up with innovative solutions to common problems by using the engineering design process. It asks you to consider which strategy is most likely to be effective. The procedure supports making decisions and addressing problems in a novel way.
Therefore, in the case above, The first step in the engineering design process is problem definition and background investigation. A solution is selected after defining the requirements. The solution is tested after a prototype is constructed. Results can be shared if the solution constructed satisfies the conditions. Thus the two options selected are correct.
Learn more about computer models from
https://brainly.com/question/22946942
#SPJ1
Answer:
Actually its A and D
Explanation:
it staff looks to provide a high level of fault tolerance while implementing a new server. with which systems configuration approach does the staff achieve this goal
The redundant component for the recovery of the system is called elasticity, which has the capacity of the system to use any alteration in the demand for media in real time, It also applies processing and storage power.
Fault toleranceIs to ensure business continuity and high availability by avoiding outages that arise from a single point of failure. The goal of fault-tolerant computing systems is to ensure business persistence and high availability by preventing downtime arising from a single point of failure.
For more about fault tolerance here https://brainly.com/question/26486347
#SPJ4
you have variable data which has the type list. which item correctly sorts the contents of data from smallest to largest?
The data.sort() method is used to sort the elements of a list in ascending order. It modifies the list in place and returns None (meaning no value is returned).
Which item correctly sorts the contents of data from smallest to largest?The sort() method sorts the elements of a given list in a specific order (either ascending or descending). It is the correct item to use to sort the contents of the list data from smallest to largest, as it will arrange the elements of the list in increasing order.
Using the sort() method is the simplest and most efficient way to sort a list in ascending order. It modifies the original list in place, meaning that the changes are made directly to the list itself, so no new list is created. Additionally, it does not return any value, so it is more efficient than other sorting algorithms.
Learn more about Programming: brainly.com/question/23275071
#SPJ4
which of these statements are true? you can select all the items in this section of the menu. in the center section of the menu, only one item can be selected at a time. details is selected. thumbnails, tiles, icons, and list are selected.
All of the statements are true:
The first statement is true because you can select all the items in the menu. The second statement is true because only one item can be selected at a time in the center section of the menu. The last statements are true because details, thumbnails, tiles, icons, and list are all selected.Selecting Menus Items in the Center SectionThe menu allows for all items in the section to be selected at once. However, in the center section of the menu, only one item can be selected at a time. Currently, the details option is selected, as well as the thumbnails, tiles, icons, and list options. All of these selections are valid and can be used to customize the menu.
Learn more about Menus: https://brainly.com/question/16851332
#SPJ4
Answer: B and D
Explanation:
Which of the following is a personal security safeguard?
A) sending valuable data only via email or IM
B) using single password for all the sites
C) removing high-value assets from computers
D) storing browsing history, temporary files, and cookies
The personal security safeguard is s removing high-value assets from computers. The correct option is C.
What is a personal security safeguard?Prescribed safeguards and controls to meet the security needs of an information system. Security features, management limitations, human security, physical structure, area, and device security are all examples of safeguards.
For extremely sensitive personal health information, encrypted storage and transfer are required.
Therefore, the correct option is C) removing high-value assets from computers.
To learn more about personal security safeguards, refer to the link:
https://brainly.com/question/24924687
#SPJ1
you have a small network with three subnets, as shown in the exhibit. ip addresses for each router interface are also indicated in the exhibit. how many ip addresses that you can assign to hosts remain on each subnet?
Subnet A =125, subnetB=0,Subnet C= 13 are the three ip addresses that needs to be assigned to the host respectively
What is a subnet?
A subnet, also known as a subnetwork, is a segmented section of a larger network. Subnets are a logical division of an IP network into multiple, smaller network segments. The Internet Protocol (IP) is a protocol used to send data from one computer to another over the internet.
For example:
A subnet is a network subnetwork that is classified as A, B, or C. For example, 172.16.0.0/16 is a class B network. This network is quite large; it begins with 172.16.A class C network would have a subnet mask of 255.255.255.0, indicating that the network uses 24 bits. This is denoted by a /24 after the IP address in CIDR notation.
Hence to conclude for the given condition Subnet A =125, subnetB=0,Subnet C= 13 are the three ip addresses that needs to be assigned to the host respectively
To know more on subnets follow this link:
https://brainly.com/question/28865562
#SPJ4
Emily is deciding between two cameras. One has a 25-megapixel rating, and the other has a 10-megapixel rating. What is the main difference between the two cameras?
Responses
The 25-megapixel camera has higher image resolution than the 10-megapixel camera.The 25-megapixel camera has higher image resolution than the 10-megapixel camera. , ,
The 10-megapixel camera has a greater depth of field than the 25-megapixel camera.
The 10-megapixel camera has a greater depth of field than the 25-megapixel camera.,
The 10-megapixel camera has a higher shutter speed than the 25-megapixel camera.
The 10-megapixel camera has a higher shutter speed than the 25-megapixel camera.,
The 25-megapixel camera has a larger maximum aperture than the 10-megapixel camera.
Answer:
D
Explanation:
The 25-megapixel camera has higher image resolution than the 10-megapixel camera.
enter your entire script below. do not include statements to drop objects as your script will be executed against a clean schema. you may include select statements in sub queries in your insert statements, but do not include select queries that return records for display. continue to use the purchase 61 and purchase item 61 tables that you created and modified in the previous problems. increase the shippping cost of every purchase from manufacturers in massachusetts ('ma') by 10%. round your calculations to two decimal points. hint: use the in clause. do not use a join
UPDATE purchase61
SET shipping_cost = ROUND(shipping_cost * 1.10, 2)
WHERE manufacturer IN (SELECT manufacturer FROM purchaseitem61 WHERE state = 'MA')
How to update the column?This statement will update the shipping_cost column in the purchase61 table for every purchase where the manufacturer is in the list of manufacturers in Massachusetts, as determined by the subquery. The shipping cost will be increased by 10% by multiplying it by 1.10, and then rounded to two decimal points using the ROUND function.
Note that you should not use a join in this statement, as the IN clause allows you to compare values in the manufacturer column with the results of the subquery without using a join.
This can make the statement more efficient and easier to read.
To Know More About SQL, Check Out
https://brainly.com/question/13068613
#SPJ1
59 which element of the cultural web represents the dress code, logos, and furnishings of an entity?
Answer:
Symbols
Explanation:
which of the following are included in r packages? select all that apply. O tests for checking your code O naming conventions for r variable names O sample datasets
O reusable r functions
The option that are included in R- packages are options:
A Tests for checking your code
C Sample datasets
D Reusable R functions
What purposes serve R packages?Extensions to the R statistical programming language are known as packages. Users of R can install R packages, which are standardized collections of code, data, and documentation, typically through a centralized software repository like CRAN (the Comprehensive R Archive Network).
Therefore, in regards to the case above, one can say that Reusable R functions, sample datasets, and tests to validate your code are all included in R packages. The instructions for using the included functions are also included in R packages.
Learn more about R- packages from
https://brainly.com/question/29414342
#SPJ1
safari uses meditation and visualization to reduce stress and improve overall well-being. what type of medical system is safari using?
Note that safari uses meditation and visualization to reduce stress and improve overall well-being. The type of medical system is safari using is: "mind-body interventions"
What are mind-body interventions?
Mind-body interventions, sometimes known as mind-body training, are health and fitness interventions that aim to improve both physical and mental health, such as yoga, tai chi, and Pilates.
In the United States, mind-body interventions are the most often utilized kind of complementary and alternative medicine, with yoga and meditation being the most popular types.
Relaxation, hypnosis, visual imagery, meditation, biofeedback, cognitive-behavioral therapy, group support, and spirituality are all examples of mind-body approaches, as are expressive arts therapies such as painting, music, or dance.
Learn more about mind-body interventions:
https://brainly.com/question/29356384?
#SPJ1
Match the type of concurrency with its description: executing two or more high-level machine instructions simultaneously executing two or more high-level statements simultaneously executing two or more subprograms simultaneously executing two or more programs simultaneously
1. Multiprocessing: executing two or more programs simultaneously.
Multiprocessing involves the concurrent execution of two or more separate programs. Each program is assigned to a different processor or core, allowing the programs to be executed in parallel.
2. Multithreading: executing two or more high-level statements simultaneously.
Multithreading is the ability of a program or an operating system to execute multiple threads of execution concurrently. Each thread of execution is a sequence of instructions that can be executed independently of other threads, allowing multiple threads to be executed at the same time.
3. Multitasking: executing two or more subprograms simultaneously.
Multitasking is the concurrent execution of multiple subprograms. Each subprogram is assigned to a different processor or core, allowing the subprograms to be executed in parallel
4. Simultaneous Multithreading: executing two or more high-level machine instructions simultaneously.
Simultaneous Multithreading (SMT) is the ability of a processor or an operating system to execute multiple threads of execution simultaneously. SMT allows multiple threads to be executed at the same time, allowing the processor or operating system to execute multiple high-level machine instructions simultaneously.
For more questions like Concurrency click the link below:
https://brainly.com/question/29673355
#SPJ4
consider the network shown in the exhibit. when you run the show interfaces command on switch1, you observe a significant number of runts on the gi0/1 interface. what does this statistic indicate?
There are collisions happening. The arp software will display all hosts on your network segment's resolved MAC to IP addresses.
The standard that enables high-bandwidth data transfer over the current cable TV infrastructure is called DOCSIS, which stands for Data Over Cable Service Interface Specification. It is essentially the technology that gives you cable internet. To find the route between two connections, use the traceroute command. A connection to another device frequently needs to pass via several routers. The names or IP addresses of each router that exists between two devices will be returned by the traceroute command.
Learn more about addresses here-
https://brainly.com/question/29065228
#SPJ4
In Java Script CodeHS, 4.2.5 " Text Message", what is the Message.java answer?
When developing web pages, applications, servers, or even games, web developers frequently use JavaScript, a lightweight programming language, to create more dynamic interactions.
Code
public class TMessage
{
private String message;
private String sender;
private String receiver;
public TMessage(String from, String to, String TheMessage)
{
sender = from;
receiver = to;
message = TheMessage;
}
public String toString()
{
return sender + " texted " + receiver + ": " + message;
}
}
To know more about Java script, check out:
https://brainly.com/question/16698901
#SPJ1
Complete the Team class implementation. For the instance method get_win_percentage(), the formula is:
wins / (wins + losses). Note: Use floating-point division.
For instance method print_standing(), output the win percentage of the team with two digits after the decimal point and whether the team has a winning or losing average. A team has a winning average if the win percentage is 0.5 or greater.
Ex: If the input is:
Ravens
13
3 where Ravens is the team's name, 13 is the number of team wins, and 3 is the number of team losses, the output is:
Win percentage: 0.81
Congratulations, Team Ravens has a winning average!
Ex: If the input is:
Angels
80
82
the output is:
Win percentage: 0.49
Team Angels has a losing average.
The complete implementation for the instance method is given as:
class Team:
def __init__(self):
self.team_name = 'none'
self.team_wins = 0
self.team_losses = 0
# TODO: Define
def get_win_percentage(self):
return self.team_wins / (self.team_wins + self.team_losses)
if __name__ == "__main__":
team = Team()
team_name = input()
team_wins = int(input())
team_losses = int(input())
team.team_name=team_name
team.team_wins=team_wins
team.team_losses=team_losses
if team.get_win_percentage() >= 0.5:
print('Congratulations, Team', team.team_name,'has a winning average!')
else:
print('Team', team.team_name, 'has a losing average.')
Note that
def get_win_percentage(self):
The above defines the function
While
return self.team_wins / (self.team_wins + self.team_losses)
This calculates the win percentage and returns it to the main.
What is a function?A function is essentially a "chunk" of code that you may reuse instead of writing it out several times. Programmers can use functions to break down or breakdown an issue into smaller segments, each of which performs a specific purpose.
Instance methods are methods that require the creation of an object of the class before they may be invoked. To call an instance method, we must first construct an Object of the class that defines the method.
Learn more about the instance method:
https://brainly.com/question/14710147
#SPJ1
What will be the output
int x = 10;
if(x > 10)
System.out.println("Thursday");
if( x < 10 )
System.out.println("Friday");
Answer:
What math is that?
Explanation:
Please show me a picture so I can help you out
if the solution obtained by an approximation algorithm is : 10 the optimal solution is : 5 what will be the value of the approximation ratio?
The value of the approximation ratio will be 2, if the solution obtained by an approximation algorithm is : 10 and the optimal solution is : 5.
What is Algorithm?
An algorithm is a step-by-step procedure that defines a sequence of instructions that must be followed in order to produce the desired result. An algorithm may be implemented in more than one programming language because algorithms are usually developed independently of underlying languages. An algorithm's characteristics include unambiguity, fineness, effectiveness, and language independence. The main factors that contribute to the importance of an algorithm are its scalability and performance.
To know more about Algorithm, visit: https://brainly.com/question/22984934?referrer=searchResults
#SPJ4
This program requires the main function and a custom value-returning function. In the main function, code these steps in this sequence:
use a list comprehension to generate 50 random integers all from -40 to 40, inclusive. These represent Celsius temperatures.
use an f_string to report the lowest and highest Celsius temperature in the list.
determine if 0C is in the list. If it is report the index where it first occurs. If it isn't in the list, report that, too.
use a random module method to create a sublist of 10 unique Celsius temperatures. sort this sublist in ascending order.
pass the Celsius sublist as the sole argument to the custom value-returning function.
In the custom function:
use either a loop or a list comprehension to create a list of 10 Fahrenheit temperatures equivalent to the Celsius temperatures. A bonus of 3 points will be awarded if a list comprehension is employed.
return the Fahrenheit list to main.
Back in main:
use a for loop and the range function to print a table showing the equivalent Celsius and Fahrenheit temperatures in columns with widths that you choose.
include column headings and display the averages as shown below.
Swedish astronomer Andres Celsius invented the centigrade scale, often known as the Celsius scale.
What is Python: Fahrenheit and centigrade temperatures?Create a Python application to translate between fahrenheit and celsius temperatures.Water freezes at 0 degrees on the centigrade scale and boils at 100 degrees. The formula for converting between centigrade and Fahrenheit is:Two temperature scales that are used today are in degrees Fahrenheit and degrees Celsius. German physicist Daniel Gabriel Fahrenheit invented the Fahrenheit scale. Water freezes at 32 degrees Fahrenheit and boils at 212 degrees Fahrenheit.C = (5/9) * (F - 32)
where F is the temperature in degrees Fahrenheit. This website also allows you to convert Fahrenheit temperatures to degrees Celsius. Simply type a Fahrenheit value into the text box below, then click the Convert button.To Learn more About Celsius scale refer To:
https://brainly.com/question/18917557
#SPJ1