Answer:
try this answer out and let see
A golf club with mass 0.5 kg is swung at 23 m/s toward a stationary golf ball on a tee. The club barely slows down to 17 m/s, but the ball flies off the tee at 69 m/s. Calculate the mass of the golf ball in kg. Answer to 4 decimals. Help fast please. Will mark brainliest
Answer:
I gotchu fam. 0.0435 kg
Explanation:
m1v1+m2v2=m1v1f+m2v2f
(0.5)(23)+(m2)(0)=(0.5)(17)+(m2)(69)
11.5=8.5+69m2
3=69m2
0.0435 kg
Calculate the amount of heat needed to convert 0.8 kg of ice at -19 °C into water at 29 °C.
10 pointss
For a two way mirror to work properly, light must be ___ on one side and ____ through the other side
a. reflected - transmitted
b. refracted - absorbed
c. absorbed- reflected
d. absorbed- transmitted
HELP!
Which of the following is true about having too little body fat?
Too little body fat can help increase your metabolism
Too little body fat is a health risk
Too little body fat can cause a heart attack
Too little body fat is good for your overall health
Which of the following is a Myth about fat loss?
Most people who are high in body fat eat too much
Any exercise that burns calories will cause the body's general fat deposit to decrease
You can lose body fat over time with regular physical activity if your calorie intake is less than calories burned in a given day
You can spot-reduce by exercising a specific body part to lose fat in that area
Which of the following statements is true about Metabolism?
Your metabolism speeds up naturally as you get older
Your basal metabolism is the amount of energy (calories) your body uses just to keep you living.
You can never speed up or slow down your body's metabolism
Your metabolism is not affected your heredity, age, and maturation
Answer:
too little body fat is a health risk
Explanation:
IF you do not have enough body fat you can have bad things happen to you
Explain why tissues in multicellular organisms are supplied with nutrients using a circulatory system.
Answer:
The tissues in a multicellular organism requires a circulatory system in other to deliver oxygen and food to the tissues while also removing carbon dioxide and metabolic wastes due the complexity of these activities
Explanation:
Multicellular organisms are organisms that are made of more than one cell. the more cells an organism has the more complex certain activities might be for the organism hence the tissues in a multicellular organism requires a circulatory system in other to deliver oxygen and food to the tissues while also removing carbon dioxide and metabolic wastes
Answer all of these questions and you will get the brain list
Answer:
1. Mechanical energy = 298.4 Joules.
2. Mechanical energy = 2140 Joules.
3. Mechanical energy = 0.2838 Joules.
Explanation:
Kinetic energy can be defined as an energy possessed by an object or body due to its motion.
Mathematically, kinetic energy is given by the formula;
[tex] K.E = \frac{1}{2}MV^{2}[/tex]
Where;
K.E represents kinetic energy measured in Joules.
M represents mass measured in kilograms.
V represents velocity measured in metres per seconds square.
Potential energy can be defined as an energy possessed by an object or body due to its position.
Mathematically, potential energy is given by the formula;
[tex] P.E = mgh[/tex]
Where,
P.E represents potential energy measured in Joules.
m represents the mass of an object.
g represents acceleration due to gravity measured in meters per seconds square.
h represents the height measured in meters.
Given the following data;
1. Kinetic energy = 182.2 J
Potential energy = 116.2 J
To find the mechanical energy;
Mechanical energy = kinetic energy + potential energy
Mechanical energy = 182.2 + 116.2
Mechanical energy = 298.4 Joules.
2. Mass = 40kg
Velocity = 3m/s
Height = 5m
We know that acceleration due to gravity is equal to 9.8m/s²
To find the mechanical energy;
We would determine the kinetic and potential energy respectively.
K.E = ½mv²
K.E = ½*40*3²
K.E = 20*9
K.E = 180 Joules.
P.E = mgh
P.E = 40*9.8*5
P.E = = 1960 Joules
Mechanical energy = K.E + P.E
Mechanical energy = 180 + 1960
Mechanical energy = 2140 Joules.
3. Mass = 0.002kg
Height = 3m
Velocity = 15m/s
To find the mechanical energy;
K.E = ½mv²
K.E = ½*0.002*15²
K.E = 0.001*225
K.E = 0.225 Joules.
P.E = mgh
P.E = 0.002*9.8*3
P.E = = 0.0588 Joules
Mechanical energy = K.E + P.E
Mechanical energy = 0.225 + 0.0588
Mechanical energy = 0.2838 Joules.
An experiment is carried out to measure the extension of a rubber band for different loads.
Complete question is;
An experiment is carried out to measure the extension of a rubber band for different loads.
The results are shown in the image attached.
What figure is missing from the table?
Answer:
17.3 cm
Explanation:
The image attached showed values for load, extension and initial length.
Now, the first length there is 15.2 cm and as such it's corresponding extension is 0 because it has no preceding measured length.
The second measured length is 16.2 cm. Since it's initial measured length is 15.2 cm, then the extension has a formula; final length - initial length.
This gives: 16.2 - 15.2 = 1 cm
This corresponds to what is given in the table.
For the next measured length, it is blank but we are given the extension to be 2.1 cm. Now, since the initial measured length is 15.2 cm.
Thus;
2.1 cm = Final length - 15.2 cm
Final length = 15.2 + 2.1
Final length = 17.3 cm
If the mass of each ball is 12 kg and they experience a gravitational force of magnitude 2.00
x 10-7 N between them, what is the distance between the balls ?
Answer:
[tex] {2 \times 10} - 7 = 12 {}^{2} \div x \\ x = 2 \times 10 - 7 \div 12 {}^{2} [/tex]
I'm just in jss2 but I read physics. this is what I think
Brainliest for correct answer :)
Answer:
B
Explanation:
The answer is b that is the final speed - initial speed divided by the time taken
Please mark as brainliest
A 1,500 kg car is at rest on a level track. The driver gives the engine gas and the car begins to accelerate forward. The car moves from 0 m/s to 27 m/s in 8 sec. What is the acceleration of the car?
Answer:
3.375 m/s²
Explanation:
Using equation of motion:
v = u + at
Here, v = 27m/s & u = 0m/s & t = 8 sec
Let the acceleration be a.
=> 27 = 0 + 8(a)
=> 27/8 = a
=> 3.375 m/s²
Alannah added a strip of zinc to a beaker containing a solution of copper
sulfate, as shown in the photo. She expected to observe the immediate
formation of solid copper in the beaker but saw no evidence of a reaction.
Alannah predicted that the reaction was happening too slowly to observe.
Which statement could best explain this result?
The solution of copper sulfate was too cold
Explanation:
The lack of an observable reaction when adding a zinc strip to a copper sulfate solution could be due to the zinc not being reactive enough, the reaction occurring too slowly, or an experimental error.
What is the lack of an observable reaction?The lack of an observable reaction refers to a situation where no visible or measurable change occurs when two or more substances are mixed or brought into contact with each other, even though a reaction was expected based on the chemical properties of the substances involved.
Here in the Question,
The lack of an observable reaction when Alannah added a strip of zinc to a beaker containing a solution of copper sulfate could be due to the following reasons:
Zinc and copper sulfate do not react: It is possible that the zinc strip and copper sulfate solution do not react with each other, leading to no observable change. This could occur if the zinc strip is not reactive enough to displace the copper in the copper sulfate solution.
Reaction is slow: Another possibility is that the reaction between zinc and copper sulfate is occurring but is happening too slowly to be observed. In this case, the reaction rate may be too low to produce an observable amount of solid copper in the beaker in a short period of time.
Experimental error: It is also possible that an error was made during the experiment that prevented the expected reaction from occurring. For example, the concentration of the copper sulfate solution may have been too low, or the zinc strip may have been coated with a layer of oxide that prevented it from reacting with the solution.
Therefore, Zinc may not be sufficiently reactive, the reaction may proceed too slowly, or there may have been a mistake in the experiment if there was no detectable reaction when a zinc strip was added to a copper sulphate solution.
To learn more about redox reaction click:
brainly.com/question/2671074
#SPJ2
If two monochromatic light waves undergo destructive interference, the amplitude of the resultant wave is
Answer: The amplitude is 0. (assuming that the amplitude ot both initial waves is the same)
Explanation:
When two monochromatic light waves of the same wavelength and same amplitude undergo destructive interference, means that the peak of one of the waves coincides with the trough of the other, so the waves "cancel" each other in that point in space.
Then if two light waves undergo destructive interference, the amplitude of the resultant wave in that particular point is 0.
Answer:
No, the resulting wave in the diagram does not demonstrate destructive interference. The resulting wave in the diagram shows a bigger wave than Wave 1 or Wave 2. If it demonstrated destructive interference, it would be a smaller wave or a horizontal line. With destructive interference, waves break down to form a smaller wave, or cancel each other out, resulting in no wave formation.
Explanation:
edge
A weight - lifter lifts a bell weighing 2 000 N and holds it in the air for 5 seconds. Has he done any work? Explain your answer.
Answer:
No, he hasn't done any work.
Explanation:
In this scenario, the weightlifter hasn't done any work because even though he lifted the bell for a specific period of time, he didn't cover any distance.
Mathematically, work done is given by the formula;
Work done = force * distance
[tex] W = F * d[/tex]
Where,
W is the work done
F represents the force acting on a body.
d represents the distance covered by the body.
Power can be defined as the energy required to do work per unit time.
Mathematically, it is given by the formula;
[tex] Power = \frac {Energy}{time} [/tex]
spheres are not perfect in space. But <> is in the cause of their shape.
Answer:
[tex] \boxed { \tt{gravitational \: pull(force)}}[/tex]
list the factor that affect the speed of sound in gases
A glass window (n = 1.52) has a
uniform layer of ice on it (n = 1.31).
What is the critical angle for a ray
trying to pass from glass to ice?
(Water n = 1.33, Air n = 1.00)
(Unit = deg)
HELP PLSS!!
Answer: 59.5 deg
Explanation: In this problem, we are giving 1.31 as n2 and 1.52 as n1. Using the formula of critical angle= arcsine(n2/n1) we get the equation critical angle=arcsine(1.31/1.52) from there, you divide 1.31 by 1.52, and get 0.862.
On your calculator you then should press 2nd and then the sine button to get sine^-1 (arcsine) and in the parenthesis after arcsine put in 0.862, the answer you get will be 59.5.
What is the equivalent resistance of a circuit that contains four 75.0 resistors connected in parallel with a 100.0 V battery?
Answer:
18.75 ohms.
Explanation:
From the question,
]When four resistors are connected in parallel in a circuit,
The equilvalent resistor is given as
1/R' = 1/R₁+1/R₂+1/R₃+1/R₄............................Equation 1
Where R' = Equivalent resistor.
Given: R₁ = R₂ = R₃ = R₄ = 75.0 ohms.
Substitute these values into equation 1
1/R' = (1/75)+(1/75)+(1/75)+(1/75)
1/R' = 4/75
R' = 75/4
R' = 18.75 ohms.
Hence the equivalent resistance = 18.75 ohms.
Answer:
18.8 ohms
Explanation:
apax
5. You are running at your maximum speed of 6m/s to catch a bus which is
standing at the bus stop. The bus move off with an acceleration of 1m/s when
you are 20 m from it.
A. Can you catch the bus?
B. Show graphically.
Una pelota recorre 20 m hacia la derecha y luego 10 m hacia la izquierda, todo en un lapso de tiempo de 10 s , cual es si velocidad y rapidez?
Answer:
v = 1 i ^ m / s, v = 1 m / s
Explanation:
In this problem we show the difference between vectors and scalars.
The average speed is
v = Δx / Δt
The bold are vectors
Δx = 20-10 = 10 i^ m
v = 10/10
v = 1 i ^ m / s
the unit vector indicates that the velocity is on the x-axis
The average speed is
v =Δx / Δt
v = 10/10
v = 1 m / s
in this case we have a scalar
which describes an object in projectile motion
Answer:
Gravity acts to push the object sideways
Explanation:
projectile motion is a motion that moves along a curved path under the action of gravity only. Hope this helps!
Convection currents will transfer heat throughout a gas until what condition arises?
A.
The gas condenses and forms a liquid.
B.
The gas particles stop moving entirely.
C.
The gas has the same temperature throughout.
D.
The gas has no thermal energy in it.
Answer:
C
Explanation:
pls mark brainlest ty
have a good day
The gas has the same temperature throughout. (C)
To 3 significant digits, what is the period of the pendulum using the equation for the period of a simple pendulum? Hint, the information you need is on the right side of the screen. The equation for the period of a pendulum is: T = 24 V
Answer:
1.42 seconds
Explanation:
T=2*pi*(sqrt length over gravity)
T=2*pi*(sqrt 0.5/9.8)
T=1.4189
Round to 3 significant digits
T=1.42 seconds
mass = 20Kg
velocity = 10m/s
what is the kinetic energy
Answer:
kinetic energy = 1 / 2 mv²
kinetic energy = 1 / 2 × 20 × 10 ²
kinetic energy = 1000 joules
.........
A player prefers to make high passes that lift the puck above the ice. Which stick should the
player choose?
Answer:
i dont know
Explanation:
hello
Which is a disadvantage of using wind as an energy source?
It may be unreliable.
It is not naturally occurring.
It produces a lot of waste.
It generates large amounts of electricity.
Answer:
it produces
Explanation:
a lot of waste
In an ecosystem,disadvantage of using wind as an energy source is that it produces a lot of waste.
What is an ecosystem?Ecosystem is defined as a system which consists of all living organisms and the physical components with which the living beings interact. The abiotic and biotic components are linked to each other through nutrient cycles and flow of energy.
Energy enters the system through the process of photosynthesis .Animals play an important role in transfer of energy as they feed on each other.As a result of this transfer of matter and energy takes place through the system .Living organisms also influence the quantity of biomass present.By decomposition of dead plants and animals by microbes nutrients are released back in to the soil.
Learn more about ecosystem,here:
https://brainly.com/question/13979184
#SPJ7
Brainliest for correct answer :))
Choose the 2nd Option.....
Ocean breezes are due to which method of heat transfer?
A. conduction
B. convection
C. greenhouse gases
D. radiation
E. geothermal energy
Ocean breezes are primarily due to convection, which is the transfer of heat through the movement of fluids or gases. The correct option is B.
What is convection?Convection is a method of heat transfer that occurs in fluids (liquids and gases) and involves the movement of material carrying thermal energy. In convection, heat is transferred by the movement of hot fluid from one place to another, which then causes the transfer of heat from the hot fluid to the cooler fluid or surface it comes into contact with.
Convection can occur in two ways:
Natural convection: It occurs due to the density differences caused by temperature variations within a fluid. When a fluid is heated, its density decreases, making it lighter and causing it to rise. As it rises, it cools, becomes denser and falls back down, creating a cycle that is known as a convection current.
Forced convection: In this type of convection, a fluid is forced to flow over a surface or through a channel, by an external agent like a fan or pump. The forced flow enhances the rate of heat transfer from the surface or through the channel, as compared to natural convection, where the fluid flow is driven only by buoyancy forces.
Convection is a very important process for heat transfer in many natural and industrial applications, including heating and cooling systems, meteorology, oceanography, and more.
Here in the Question,
Ocean breezes are primarily due to convection, which is the transfer of heat through the movement of fluids or gases. As the sun heats up the surface of the ocean, the air above it also heats up and rises. This creates a low pressure area that draws in cooler air from over the land, resulting in a breeze that blows from the ocean towards the shore. This is why sea breezes are generally felt during the day, when the land is warmer than the sea, and why they tend to die down at night, when the opposite occurs.
Therefore, The correct answer is B i.e convection.
To learn about the difference between conduction and convection click:
https://brainly.com/question/13104912
#SPJ7
Which motions are the components of projectile motion? A and B B and C A and C None of these are correct combinations.
Answer:
its A and B
Explanation:
Answer:
A or A and B
Explanation:
correct on edge 2021
what color of colors of light does red glass absorb
Helppppp meeeeee pleaseeeeeeeee