Help pls. Edge 2021- Motion in space

Answer:

Mass, m = 6.18 kg

Explanation:

Given the following data;

Frequency, F = 10 Hz

Spring constant, k = 250 N/m

We know that pie, π = 22/7

To find the mass, we would use the following formula;

F = 1/2π√(k/m)

Where;

F is the frequency of oscillation.

k is the spring constant.

m is the mass of the spring.

Substituting into the formula, we have;

10 = 1/2 * 22/7 * √250/m

10 = 22/14 * √250/m

Cross-multiplying, we have;

140 = 22 * √250/m

Dividing both sides by 22, we have;

140/22 = √250/m

6.36 = √250/m

Taking the square of both sides, we have;

6.36² = (√250/m)²

40.45 = 250/m

Cross-multiplying, we have;

40.45m = 250

Mass, m = 250/40.45

Mass, m = 6.18 kg

Answer:

If the frequency of a wave is doubled, what happens to its wavelength? If the frequency is doubled, the wavelength is only half as long. 3. ... As the frequency slows down, the wavelength increases.

Explanation:

Answer:

Explanation:

The relation between time period of moon in the orbit around a planet can be given by the following relation .

T² = 4 π² R³ / GM

G is gravitational constant , M is mass of the planet , R is radius of the orbit and T is time period of the moon .

Substituting the values in the equation

(.3189 x 24 x 60 x 60 s)²  = 4 x 3.14² x ( 9380 x 10³)³ / (6.67 x 10⁻¹¹ x M)

759.167 x 10⁶ = 8.25 x 10²⁰ x 39.43 / (6.67 x 10⁻¹¹ x M )

M = .06424  x 10²⁵

= 6.4 x 10²³ kg .

Answer:

9000

Explanation:

f=ma

f= force

m=mass

a=acceleration

f=ma

4500×2.0

9000N

Ray B. isn't possible for a converging lens, because after passing through focus ot would go parallel to the principal axis,

So, Correct option is :

=》Option B.)

Answer:

The answer is C the ball is not in a closed system and experience an impulse.

Explanation:

Answer:

8.24 m/s²

Explanation:

Applying,

T = 2π√(L/g).................... Equation 1

Where T = period of the pendulum, L = Length of the pendulum, g = acceleration due to gravity of the planet, π = pi

From the question, we were asked to  find the value of g,

There we make g the subject of the equation

g = 4π²L/T²..................... Equation 2

Given: L= 48 cm = 0.48 m, T = (141/93) s = 1.516 s

Constant: π = 3.14

Substitute these values into equation 2

g = 4(3.14²)(0.48)/(1.516²)

g = 18.93/2.298

g = 8.24 m/s².

Hence the acceleration of the planet is 8.24 m/s²

Answer:

t = 3.924 s

Explanation:

First, we will calculate the amount of work required to get the astronaut back to the capsule:

[tex]W = Fd\\[/tex]

where,

W = work required = ?

F = Force = Weight = mg = (80 kg)(9.81\ m/s²) = 784.8 N

d = distance = 5 m

Therefore,

[tex]W = (784.8\ N)(5\ m)\\W = 3924 J[/tex]

Now the time can be calculated as:

[tex]Power = \frac{W}{t}\\t = \frac{W}{Power}\\\\t = \frac{3924\ J}{1000\ W}\\\\[/tex]

t = 3.924 s

Answer: I think it’s Global for the 1st one

And free trade for the 2nd one

Explanation:

The correct answer is: "After World War II, political leaders from various countries discussed ways to strengthen individual economies." They began promoting economic policies to boost production and exports.

After World War II, many countries were left with weakened economies and infrastructure, and there was a need for economic recovery and growth. To achieve this, political leaders from different countries came together to discuss ways to strengthen their individual economies and also promote international economic cooperation. One of the ways they did this was by promoting economic policies that aimed to boost production and exports. This involved policies that encouraged businesses to increase their output and create more jobs, as well as policies that made it easier for countries to trade with each other.

Hence, after World War II, political leaders from various countries discussed ways to strengthen their individual economies. They began promoting economic policies to boost production and exports.

Learn more about World War II's aftermath here.

https://brainly.com/question/27327667

#SPJ5

Answer:i

Explanation:

Answer:

+1.46×10¯⁶ C

Explanation:

From the question given above, the following data were obtained:

Charge 1 (q₁) = +26.3 μC = +26.3×10¯⁶ C

Force (F) = 0.615 N

Distance apart (r) = 0.750 m

Electrical constant (K) = 9×10⁹ Nm²/C²

Charge 2 (q₂) =?

The value of the second charge can be obtained as follow:

F = Kq₁q₂ / r²

0.615 = 9×10⁹ × 26.3×10¯⁶ × q₂ / 0.750²

0.615 = 236700 × q₂ / 0.5625

Cross multiply

236700 × q₂ = 0.615 × 0.5625

Divide both side by 236700

q₂ = (0.615 × 0.5625) / 236700

q₂ = +1.46×10¯⁶ C

NOTE: The force between them is repulsive as stated from the question. This means that both charge has the same sign. Since the first charge has a positive sign, the second charge also has a positive sign. Thus, the value of the second charge is +1.46×10¯⁶ C

Answer:

+1.46

Explanation:

acellus

Answer:

D. The particles move more quickly and begin to move from place to place.

Explanation:

Explanation:

answer is that i think???

Answer:

Aerobic exercise is an important component of a healthy lifestyle. Find out more about aerobic equipment that can help keep you fit.

Aerobic equipment simulates the movements of aerobic exercises such as walking, jogging, rowing, skiing, hiking, biking, and climbing. These activities rhythmically and continuously move your large muscles — the key to getting your heart beating fast enough and long enough for aerobic conditioning.

Answer:

c. -288 J

Explanation:

Given;

mass of the block, m = 4 kg

velocity of the block, v = 12 m/s

deceleration of the block, a = 3 m/s²

Apply work-energy theorem;

work done in stopping the block = kinetic energy of the block

W = ¹/₂mv²

where;

W is the magnitude of the work done by the force

W = ¹/₂ x 4 x 12²

W = 288 J

Since the work done by the force is in opposite direction, then the value of the work done by the force is -288 J

Answer:

The answer is B.

Explanation:

مافيني اشرح

Most hair dryers are in the 1800 watt range and lets assume you turned it to the highest speed and heat setting.

It will heat up the air in the box, failry quickly. Rules of thermodynamics says that the heat will increase the temperature according to the rate of heat input minus the rate of heat loss from the box… due to conduction, radiation and convection (in this case none of the latter because the box is sealed).

The loss rate depends in the temperature difference and the thermal resistance. THicker and better insulation increases the resistance; larger area decreases the resistance. Eventually the heat (temperature) will rise and the difference between inside and outside will be so large that the temperature will rise no more. But in the case of a 1800 W hairdryer the temperature will exceed the melting point of plastics and wire insulation and if allowed to come to heat equilibrium will probably short out and catch fire or blow an external fuse.

Most modern hair dryers have a internal thermal fuse that cuts out at temperatures below the melting point and probably this will cut off the dryer before catastrophic meltdown. Its a one time fuse and not readily available, mostly you toss the dryer when the fuse goes

The devices don't "draw" 120v. The 120v comes to your house from the power company. They decide it should be 120v and that's what they send you. It's hypothetically technically possible for you to change that, but if you try it, you'll definitely burn the house down.

The total resistance of those two devices in parallel is 6 and 2/3 ohms. That doesn't depend on what they're plugged into. It would still be 6 and 2/3 ohms if they were connected in parallel, wrapped in tissue, sealed in a jar of chicken soup and stored in a box on a high shelf.

But since they ARE plugged into 120v, they draw 18 Amperes from the socket, and they turn all of that electrical energy into 2160 watts of heat. That's about the same as a good size toaster oven, and you have to figure out a way to get rid of all that heat before you burn the house down.

Force = mass × acceleration

9 = 65 x acceleration

acceleration= 9/65 = 0.318 m/s2

Acceleration Tecle, with a mass of 65.0 kg, is standing on an ice-skating rink. His friend applies a force of 9.0 N to him.  Tecle's resulting acceleration is  0.318 m/s²

The rate at which an item changes its velocity is known as acceleration, a vector quantity. If an object's velocity is changing, it is acceleration.

The net acceleration that objects get as a result of the combined action of gravity and centrifugal force is known as the Earth's gravity, or g. It is a vector quantity whose strength or magnitude is determined by the norm and whose direction correlates with a plumb bob.

Force = mass × acceleration

9 = 65 x acceleration

acceleration= 9/65 = 0.318 m/s²

Acceleration Tecle, with a mass of 65.0 kg, is standing on an ice-skating rink. His friend applies a force of 9.0 N to him.  Tecle's resulting acceleration is  0.318 m/s²

To learn more about acceleration refer to the link:

brainly.com/question/12550364

#SPJ2

Answer:

b. 600,000 J

Explanation:

Applying the law of conservation of energy,

The thermal energy created = Kinetic energy of the suv.

Q' = 1/2(mv²)............... Equation 1

Where Q' = Thermal energy, m = mass of the suv, v = velocity of the suv.

From the question,

Given: m = 3000 kg, v = 20 m/s

Substitute these values into equation 1

Q' = 1/2(3000×20²)

Q' = 600000 J

Hence the right option is b. 600,000 J

Answer:

6.4 cm.

Explanation:

From the question given above, the following data were obtained:

Coefficient of linear expansion (α) = 25×10¯⁶ / °C

Original length (L) = 4850 cm

Initial temperature (T₁) = 2 °C

Final temperature (T₂) = 55 °C

Change in length (ΔL) =?

The change in the length of the wire can be obtained as follow:

α = ΔL / L(T₂ – T₁)

25×10¯⁶ = ΔL / 4850(55 – 2)

25×10¯⁶ = ΔL / 4850 × 53

25×10¯⁶ = ΔL / 257050

Cross multiply

ΔL = 25×10¯⁶ × 257050

ΔL = 6.4 cm

Therefore, the change in the length of the wire is 6.4 cm

Answer:

A,B,C,D,F,G

Explanation:

Edge 2021

The atoms, subatomic particles, particles that are 10^-9m, microtechnology systems, neutrons and particles that are 10^-3m  will displays the effects of quantum mechanics.

Quantum Mechanics is the branch of mechanics deals with the mathematical description of the motion and interaction of subatomic particles, incorporating the concepts of quantization of energy, wave–particle duality, the uncertainty principle, and the correspondence principle is Quantum Mechanics.

It is theory says at subatomic level, energy exists in discrete levels as "quanta" and particles behave as waves.

A Subatomic particles are the particle that are present inside an atom. These particles are electrons, protons, and neutrons.

Thus, atoms, subatomic particles, particles that are 10^-9m, microtechnology systems, neutrons and particles that are 10^-3m  will displays the effects of quantum mechanics.

Learn more about Quantum Mechanics;

brainly.com/question/7221719

#SPJ2

Answer:

Explanation:

No sound is heard , that means there is destructive interference at the place where sound is heard .

Path difference of the source of sound = 1.425 m - 1.230 m

= 0.195 m

Let frequency of sound be n .

wave length = velocity of sound at 0°C / n

λ = 330 / n

for destructive interference ,

path difference = ( 2m+1) λ /2 , where λ is wave length of sound.

0.195 m = ( 2m+1) λ /2

0.195 m = ( 2m+1)330 / 2n

2n = 1692.3 (2m+1)

If m = 0

n = 846 . which is nearest to given frequency of 993 Hz

So 993 Hz is the answer.

Answer:

Explanation:

1/v - 1/u = 1/f

given, f = 0.3 m, u = -0.4m

so, 1/v - 1/-0.4 = 1/0.3

or, 1/v = 1/0.3 - 1/0.4 = 1/1.2

v = 1.2 m

now, differentiating 1/v - 1/u = 1/f with respect to t,

-1/v² dv/dt + 1/u² du/dt = 0

or, dv/dt = (v/u)² du/dt

putting, du/dt = 0.01 m/s , v = 1.2 m and u = -0.4 m

so, dv/dt = (1.2/-0.4)² × 0.01

= 0.09 m/s

hence, speed of image with respect to lens is 0.09 m/s .

from formula of magnification

magnification, m = v/u

differentiating with respect to time both sides,

dm/dt = (u dv/dt - vdu/dt)/u²

= (-0.4 × 0.09 - 1.2 × 0.01)/(-0.4)²

= (-0.036 - 0.012)/0.16

= -0.048/0.16

= -0.3 m/s

hence, magnitude of rate of change of lateral magnification is 0.3 m/s

Answer:

Reaction rate are not sensitive to temperature.

Answer:

1) ngle of incidence and reflection are equal,  light carries does not change

2) the angle of this line with respect to the surface is 90º

3) protractor

4)    n₂  sin θ₂ = n_1 sin θ₁,  light ray must have a greater angle than the incident ray ,

Explanation:

1) When light falls on a reflective surface, the angle of incidence and reflection are equal and as it travels in the same medium, the speed that the light carries does not change

2) The normal is a line perpendicular to the point of incidence of light, so the angle of this line with respect to the surface is 90º

3) Angles are measured with a protractor

4) When light passes from one medium to another, the speed of the ray changes due to the difference in the refractive index in each medium, due to this change in speed the transmitted light ray must have a greater angle than the incident ray , since the speed increases as the density of the medium decreases

           [tex]\frac{sin \theta _2}{ sin \theta_1} = \frac{v_2}{v_1}[/tex]

          [tex]\frac{c}{v_2} \ sin \theta_2 = \frac{c}{v_1} \ sin \theta_1[/tex]

          n₂  sin θ₂ = n_1 sin θ₁