The expression for the kinetic energy of the car at the top of the loop is KE = m * g * (2h - 2r)
To find an expression for the kinetic energy of the car at the top of the loop, we can use the following terms: mass (m), gravitational acceleration (g), height (h), and radius (r). The kinetic energy (KE) can be expressed as:
KE = 1/2 * m * v^2
At the top of the loop, the car has both kinetic and potential energy. The potential energy (PE) is given by:
PE = m * g * (2r - h)
Since the car's total mechanical energy is conserved throughout the loop, we can find the initial potential energy at the bottom of the loop, when the car has no kinetic energy:
PE_initial = m * g * h
Now, we can equate the total mechanical energy at the top and the bottom of the loop:
PE_initial = KE + PE
Solving for the kinetic energy (KE):
KE = m * g * h - m * g * (2r - h)
KE = m * g * (h - 2r + h)
KE = m * g * (2h - 2r)
So the expression for the kinetic energy of the car at the top of the loop is:
KE = m * g * (2h - 2r)
Learn more about "kinetic energy":
https://brainly.com/question/8101588
#SPJ11
A carpet which is 10 meters long is completely rolled up. When x meters have been unrolled, the force required to unroll it further is given by F(x)=900/(x+1)3 Newtons. How much work is done unrolling the entire carpet?
A carpet which is 10 meters long is completely rolled up. When x meters have been unrolled, the force required to unroll it further is given by F(x)=900/(x+1)3 Newtons. The work done unrolling the entire 10-meter carpet is approximately 317.74 joules.
To calculate the work done unrolling the entire carpet, we need to find the integral of the force function F(x) = 900/(x+1)^3 with respect to x over the interval [0, 10]. This will give us the total work done in joules.
The integral is:
∫(900/(x+1)^3) dx from 0 to 10
Using the substitution method, let u = x + 1, then du = dx. The new integral becomes:
∫(900/u^3) du from 1 to 11
Now, integrating this expression, we get:
(-450/u^2) from 1 to 11
Evaluating the integral at the limits, we have:
(-450/121) - (-450/1) ≈ 317.74 joules
Therefore, the work done unrolling the entire 10-meter carpet is approximately 317.74 joules.
Learn more about work here:
https://brainly.com/question/31655489
#SPJ11
A +6.00 -μC point charge is moving at a constant 8.00×106 m/s in the + y-direction, relative to a reference frame. At the instant when the point charge is at the origin of this reference frame, what is the magnetic-field vectorit produces at the following points.
Part A: x = +.5 m, y = 0 m, z = 0 m
Part B: x = 0 m, y = -.5 m, z = 0 m
Part C: x = 0 m, y = 0 m, z = +.5 m
Part D: x = 0 m, y = -.5 m, z = +.5 m
The magnetic field vector at point D will be B = Bx i + By j = (-3.83 × 10⁻⁵ T) i + (1.67 × 10⁻⁵ T) j.
Part A: At point A, the magnetic field vector produced by the moving point charge will be in the z-direction and can be calculated using the formula for the magnetic field of a moving point charge. The magnitude of the magnetic field can be calculated using the formula
B = μ₀qv/4πr²,
where μ₀ is the permeability of free space, q is the charge, v is the velocity, and r is the distance from the charge.
Substituting the given values,
we get
B = (4π × 10⁻⁷ T·m/A)(6.00 × 10⁻⁶ C)(8.00 × 10⁶ m/s)/(4π(0.5 m)²)
= 3.83 × 10⁻⁵ T, directed in the positive z-direction.
Part B: At point B, the magnetic field vector produced by the moving point charge will be in the x-direction and can be calculated using the same formula as in Part A.
Substituting the given values, we get
B = (4π × 10⁻⁷ T·m/A)(6.00 × 10⁻⁶ C)(8.00 × 10⁶ m/s)/(4π(0.5 m)²)
= 3.83 × 10⁻⁵ T,
directed in the negative x-direction.
Part C: At point C, the magnetic field vector produced by the moving point charge will be in the y-direction and can be calculated using the same formula as in Part A. Substituting the given values, we get
B = (4π × 10⁻⁷ T·m/A)(6.00 × 10⁻⁶ C)(8.00 × 10⁶ m/s)/(4π(0.5 m)²)
= 3.83 × 10⁻⁵ T,
directed in the positive y-direction.
Part D: At point D, the magnetic field vector produced by the moving point charge will have both x and y components and can be calculated using vector addition of the individual components. The x-component will be the same as in Part B, i.e., Bx = -3.83 × 10⁻⁵ T.
The y-component can be calculated using the formula
By = μ₀qvz/4πr³,
where vz is the velocity component in the z-direction. Substituting the given values, we get
By = (4π × 10⁻⁷ T·m/A)(6.00 × 10⁻⁶ C)(8.00 × 10⁶ m/s)(0.5 m)/(4π(0.5² + 0.5²)³/2)
= 1.67 × 10⁻⁵ T,
directed in the positive y-direction.
Therefore, the magnetic field vector at point D would be B = Bx i + By j = (-3.83 × 10⁻⁵ T) i + (1.67 × 10⁻⁵ T) j.
To know more about the Point charge, here
https://brainly.com/question/28354110
#SPJ4
A guitar string with mass density μ = 2.3 × 10-4 kg/m is L = 1.07 m long on the guitar. The string is tuned by adjusting the tension to T = 114.7 N.
1. With what speed do waves on the string travel? (m/s)
2. What is the fundamental frequency for this string? (Hz)
3. Someone places a finger a distance 0.169 m from the top end of the guitar. What is the fundamental frequency in this case? (Hz)
4. To "down tune" the guitar (so everything plays at a lower frequency) how should the tension be adjusted? Should you: increase the tension, decrease the tension, or will changing the tension only alter the velocity not the frequency?
(1) speed do waves on the string travel = 503.6 m/s, (2) the fundamental frequency for this string= 235.6 Hz, (3) undamental frequency in this case= 277.7 Hz and (4) To down tune the guitar, the tension should be decreased
1. The speed of waves on the guitar string can be calculated using the formula v = sqrt(T/μ), where T is the tension and μ is the mass density. Substituting the given values, we get v = sqrt(114.7 N / 2.3 × 10-4 kg/m) = 503.6 m/s.
2. The fundamental frequency of the guitar string can be calculated using the formula f = v/2L, where v is the speed of waves and L is the length of the string. Substituting the given values, we get f = 503.6/(2 × 1.07) = 235.6 Hz.
3. When a finger is placed a distance d from the top end of the guitar, the effective length of the string becomes L' = L - d. The fundamental frequency in this case can be calculated using the same formula as before, but with the effective length L'. Substituting the given values, we get f' = 503.6/(2 × (1.07 - 0.169)) = 277.7 Hz.
4. This is because the frequency of the string is inversely proportional to the square root of the tension, i.e., f ∝ sqrt(T). Therefore, decreasing the tension will lower the frequency of the string. Changing the tension will also alter the velocity, but since frequency depends only on tension and density, it will also be affected.
To know more about density visit:
https://brainly.com/question/29775886
#SPJ11
In pushing a 0.024-kg dart into a toy dart gun, you have to exert an increasing force that tops out at 7.0 N when the spring is compressed to a maximum value of 0.16 m .
Part A
What is the launch speed of the dart when fired horizontally?
Part B
Does your answer change if the dart is fired vertically?
Part A: the launch speed of the dart when fired horizontally is 6.67 m/s. Part B: If the dart is fired vertically, the launch speed would be different as the force of gravity would act on the dart in addition to the force from the spring.
To calculate the launch speed of the dart, we can use the principle of conservation of mechanical energy, which states that the initial mechanical energy of the system is equal to the final mechanical energy of the system neglecting any non-conservative forces such as air resistance. At the start of the process, the spring has only potential energy, which is given by:
U = (1/2)kx^2
where k is the spring constant and x is the maximum compression of the spring. At maximum compression, all of the potential energy is converted to kinetic energy of the dart, which is given by:
K = (1/2)mv^2
where m is the mass of the dart and v is its velocity.
Part A:
To calculate the launch speed of the dart when fired horizontally, we need to find the spring constant k. We can do this by using the maximum force exerted on the dart and the maximum compression of the spring:
F = kx
where F = 7.0 N and x = 0.16 m. Solving for k, we get:
k = F/x = 7.0 N/0.16 m = 43.75 N/m
Now we can use this value of k to calculate the launch speed of the dart:
(1/2)kx^2 = (1/2)mv^2
Solving for v, we get:
v = sqrt[(kx^2)/m] = sqrt[(43.75 N/m)(0.16 m)^2/(0.024 kg)] = 6.67 m/s
So, the launch speed of the dart when fired horizontally is 6.67 m/s.
Part B:
The launch speed of the dart would be different if it were fired vertically. This is because the force of gravity would act on the dart in addition to the force from the spring. The force from the spring would act in the opposite direction of gravity, so the dart would not travel as far. To calculate the launch speed in this case, we would need to consider the forces acting on the dart and use the principle of conservation of mechanical energy again.
Therefore, Part A: When the dart is shot horizontally, its launch speed is 6.67 m/s. Part B: The launch speed would change if the dart was fired vertically because gravity's pull on the dart would be added to the spring's force.
To learn more about projectile motion click:
https://brainly.com/question/29545516
#SPJ1
you have constructed a simple linear regression model and are testing whether the assumption of linearity is reasonably satisfied. select the scatter plot that indicates linearity:
A scatter plot that shows a straight-line pattern with tightly clustered points around the trendline and no discernible pattern in the residuals is indicative of linearity and satisfies the assumption of linearity in a simple linear regression model.
To test whether the assumption of linearity is reasonably satisfied in a simple linear regression model, we need to plot the relationship between the independent variable (X) and the dependent variable (Y). A scatter plot is a useful tool to visualize this relationship.
A linear relationship between X and Y implies that as X increases or decreases, Y changes in a constant proportion. Therefore, a scatter plot that shows a straight-line pattern (either upward or downward) is indicative of linearity.
In contrast, a scatter plot that shows a curved pattern or a scattered cluster of points is indicative of non-linearity. In such cases, the simple linear regression model may not be appropriate, and a more complex model may be necessary.
Therefore, the scatter plot that indicates linearity is the one that shows a clear and consistent upward or downward trend. The points should be tightly clustered around the trendline, and there should be no discernible pattern in the residuals (the differences between the actual and predicted values of Y).
To learn more about scatter plots
https://brainly.com/question/29231735
#SPJ4
Parallel light rays cross interfaces from air into two different media, 1 and 2, as shown in the figures below. In which of the media is the light traveling faster and why?
Light travels faster in medium 2 because it has a lower refractive index compared to medium 1.
Light travels at different speeds in different materials, which is determined by their refractive index.
The refractive index is a measure of how much a material can bend light.
When parallel light rays cross interfaces from air into two different media, the angle of refraction changes.
The speed of light in the media is inversely proportional to the refractive index.
Therefore, the medium with the lower refractive index will have a faster speed of light.
In the figures provided, medium 2 has a lower refractive index compared to medium 1.
Hence, light travels faster in medium 2 than in medium 1.
For more such questions on refractive, click on:
https://brainly.com/question/14191704
#SPJ11
Light travels faster in medium 2 because it has a lower refractive index compared to medium 1.
Light travels at different speeds in different materials, which is determined by their refractive index.
The refractive index is a measure of how much a material can bend light.
When parallel light rays cross interfaces from air into two different media, the angle of refraction changes.
The speed of light in the media is inversely proportional to the refractive index.
Therefore, the medium with the lower refractive index will have a faster speed of light.
In the figures provided, medium 2 has a lower refractive index compared to medium 1.
Hence, light travels faster in medium 2 than in medium 1.
Visit to know more about Refractive:-
brainly.com/question/14191704
#SPJ11
Select the correct mechanism responsible for the formation of the Oort cloud and the Kuiper belt. the ejection of planetesimals due to their gravitational interaction with giant planets the ejection of planetesimals due to radiation pressure from the Sun the ejection of planetesimals due to the explosive death of a star that preceded the Sun the formation of planetesimals in their current locations, far from the Sun
The mechanism is the ejection of planetesimals due to gravitational interaction with giant planets.
The formation of the Oort cloud and the Kuiper belt is primarily attributed to the ejection of planetesimals because of their gravitational interaction with giant planets, such as Jupiter and Saturn.
During the early stages of our solar system's formation, these massive planets' gravitational forces caused planetesimals to be scattered and ejected into distant orbits.
This process led to the formation of the Oort cloud and the Kuiper belt, which are now located far from the Sun and consist of numerous icy objects and other small celestial bodies.
For more such questions on gravitational, click on:
https://brainly.com/question/72250
#SPJ11
The correct mechanism responsible for the formation of the Oort Cloud and the Kuiper Belt is the ejection of planetesimals due to their gravitational interaction with giant planets. This mechanism is supported by the widely accepted theory known as the "Nice model."
During the early stages of our solar system, planetesimals were abundant and played a crucial role in the formation of planets. The gravitational interactions between these planetesimals and giant planets, such as Jupiter and Saturn, led to the ejection of some of these smaller bodies into distant orbits. Over time, these ejected planetesimals settled into the regions now known as the Oort Cloud and the Kuiper Belt.
The Oort Cloud is a vast, spherical shell of icy objects surrounding the solar system at a distance of about 50,000 to 100,000 astronomical units (AU) from the Sun. The Kuiper Belt, on the other hand, is a doughnut-shaped region of icy bodies located beyond Neptune's orbit, at a distance of about 30 to 50 AU from the Sun. Both regions contain remnants of the early solar system and are believed to be the source of some comets that periodically visit the inner solar system.
In summary, the gravitational interactions between planetesimals and giant planets led to the formation of the Oort Cloud and the Kuiper Belt, serving as distant reservoirs of primordial material from the early stages of our solar system's development.
learn more about Kuiper Belt here: brainly.com/question/25583240
#SPJ11
check point: what wavelength in angstroms do you measure the line for ngc 2903 at?
The wavelength in angstroms for the line of NGC 2903, more information is needed, such as the specific spectral line you are referring to or the element being observed..
Spectral lines are specific wavelengths of light that are emitted or absorbed by atoms and molecules. The wavelength of a spectral line is determined by the energy levels of the atoms or molecules involved in the transition. Therefore, we need to know which spectral line in NGC 2903 is being observed. Once we have that information, we can look up the corresponding wavelength in angstroms.
NGC 2903 is a barred spiral galaxy, and it can emit various spectral lines depending on the elements present in the galaxy. Spectral lines are unique to each element and can be used to identify the elements in the galaxy. However, without knowing the specific spectral line or element you are referring to, it's not possible to provide the exact wavelength in angstroms.
To know more about wavelength visit:
https://brainly.com/question/13533093
#SPJ11
find the mass m of the counterweight needed to balance a truck with mass m = 1 320 kg truck on an incline of = 45°. assume both pulleys are frictionless and massless.
The mass of the counterweight needed to balance the truck is approximately 935 kg.
To find the mass of the counterweight needed to balance the truck, we need to use the principle of moments, which states that the sum of clockwise moments about a point must be equal to the sum of anticlockwise moments about the same point.
Therefore, the mass of the counterweight needed to balance the truck is 910 kg.
where m_truck is the mass of the truck (1,320 kg), g is the acceleration due to gravity (9.81 m/s^2), theta is the angle of inclination (45°), and m_counterweight is the mass of the counterweight we need to find.
First, convert the angle to radians:
theta = 45° * (pi/180) = 0.7854 radians
Now, calculate the force acting on the truck:
F_truck = m_truck * g * sin(theta) = 1,320 kg * 9.81 m/s^2 * sin(0.7854) ≈ 9,170 N
Since the system is in equilibrium, the force acting on the counterweight must be equal to the force acting on the truck:
F_counterweight = m_counterweight * g = 9,170 N
Finally, find the mass of the counterweight:
m_counterweight = F_counterweight / g = 9,170 N / 9.81 m/s^2 ≈ 935 kg
To know more about mass visit :-
https://brainly.com/question/30337818
#SPJ11
the maximum gauge pressure in a hydraulic lift is 17 atm. if the hydraulic can lift a maximum 8730 kg of mass, what must be the diameter of the output line in (a) meter, b) cm, and c) inch ?
The diameter of the output line of a hydraulic lift that can generate a maximum gauge pressure of 17 atm and lift a maximum mass of 8730 kg is 80.1 cm².
To calculate the diameter of the output line, we use the formula: pressure = force / area
where force is the weight of the mass being lifted, and area is the cross-sectional area of the output line. First, we convert the maximum weight the hydraulic lift can lift from kg to N (newtons): force = mass x gravity
force = 8730 kg x 9.81 m/s² = 85,556.5 N
Now we can calculate the area of the output line using the formula:
area = force / pressure
area = 85,556.5 N / 17 atm = 5,032.2 cm²
To convert the area to cm, we use the formula:
1 cm² = 0.0001 m²
Therefore, the area in cm² is 503.22 cm². Finally, we calculate the diameter of the output line using the formula:area = π x (diameter/2)²
diameter = √(4 x area / π)
diameter = √(4 x 503.22 cm² / π) = 80.1 cm
Therefore, the diameter of the output line is 80.1 cm.
Learn more about gauge pressure here:
https://brainly.com/question/29341536
#SPJ11
.18 the value of p0 in silicon at t 300 k is 2 1016 cm3 . (a) determine ef ev. (b) calculate the value of ec ef. (c) what is the value of n0? (d) determine efi ef
(a) 0.56 eV (b) The value of ec ef is 1.12 eV (c) The value of n0 is [tex]10^{10}[/tex] [tex]cm^{-3[/tex] (d) 0.31 eV above the valence band.
(a) The value of ef - ev can be determined by using the equation Ef = (Ev + Ec)/2 + (kT/2)ln(Nv/Nc), where Ev is the energy of the valence band, Ec is the energy of the conduction band, k is the Boltzmann constant, T is the temperature in Kelvin, and Nv/Nc is the ratio of the effective density of states in the valence band to that in the conduction band. Plugging in the given values, we get Ef - Ev = 0.56 eV.
(b) The value of ec - Ef can be calculated using the equation Ec - Ef = Ef - Ev, which gives us Ec - Ef = 1.12 eV.
(c) The value of n0 can be found using the equation n0 = Nc exp(-(Ec - Ef)/kT), where Nc is the effective density of states in the conduction band. Plugging in the given values, we get n0 = [tex]10^{10} cm^{-3}.[/tex]
(d) The value of efi - Ef can be determined using the equation efi - Ef = kTln(n/ni), where ni is the intrinsic carrier concentration. Plugging in the given values, we get efi - Ef = 0.31 eV above the valence band.
For more such questions on valence band, click on:
https://brainly.com/question/16050766
#SPJ11
what are the potential environmental consequences of using synthetic fertilizers?
Use of synthetic fertilizers can lead to water pollution, soil degradation, and greenhouse gas emissions, which negatively impact ecosystems, biodiversity, and overall environmental health. To mitigate these effects, sustainable agricultural practices such should be considered.
Water pollution can occur when excessive fertilizer use leads to nutrient runoff into water bodies, causing eutrophication. This process stimulates algal blooms, which deplete oxygen levels and harm aquatic life, disrupting ecosystems and biodiversity.
Soil degradation can result from the overuse of synthetic fertilizers, as they can cause a decline in soil organic matter and contribute to soil acidification. This reduces the soil's ability to retain water, leading to decreased fertility and erosion, which in turn affects crop yield and long-term agricultural sustainability.
Greenhouse gas emissions are another concern, as the production and application of synthetic fertilizers can generate significant amounts of nitrous oxide (N2O), a potent greenhouse gas. N2O emissions contribute to climate change and can further exacerbate environmental issues such as sea level rise, extreme weather events, and loss of biodiversity.
Know more about biodiversity here:
https://brainly.com/question/13073382
#SPJ11
true/false. determine whether each statement is true or false. justify each answer. question content area bottom part 1 a. a vector is any element of a vector space.
This statement "a vector is any element of a vector space" is True.
A vector is any element of a vector space, as a vector space is a collection of objects called vectors, which satisfy certain axioms such as closure under addition and scalar multiplication.
A vector can be represented as a directed line segment in Euclidean space with a magnitude and direction, or as an n-tuple of numbers in an abstract vector space. Therefore, a vector is by definition an element of a vector space.
To know more about vector refer here
https://brainly.com/question/29740341#
#SPJ11
A cylindrical capacitor has inner and outer radii at 5 mm and 15 mm, respectively, and the space between the conductors is filled with a dielectric material with relative permittivity of 2.0. The inner conductor is maintained at a potential of 100 V while the outer conductor is grounded. Find: (a) the voltage midway between the conductors, (b) the electric field midway between the conductors, and c) the surface charge density on the inner and outer conductors.
The surface charge density on the outer conductor is zero, since it is grounded and has no net charge.
(a) The voltage midway between the conductors can be calculated using the formula V = V1 - V2, where V1 is the voltage on the inner conductor and V2 is the voltage on the outer conductor. So, V = 100 V - 0 V = 100 V.
(b) The electric field midway between the conductors can be calculated using the formula E = V/d, where V is the voltage and d is the distance between the conductors. Here, the distance is the average of the inner and outer radii, which is (5 mm + 15 mm)/2 = 10 mm = 0.01 m. So, E = 100 V/0.01 m = 10,000 V/m.
(c) The surface charge density on the inner conductor can be calculated using the formula σ = ε0εrE, where ε0 is the permittivity of free space, εr is the relative permittivity, and E is the electric field. Here, σ = ε0εrE(1/r), where r is the radius of the inner conductor. So, σ = (8.85 x 10^-12 F/m)(2.0)(10,000 V/m)(1/0.005 m) = 3.54 x 10^-7 C/m^2.
The surface charge density on the outer conductor is zero, since it is grounded and has no net charge.
To know more about Electric field visit:
https://brainly.com/question/8971780
#SPJ11
Light of wavelength 631 nm passes through a diffraction grating having 299 lines/mm .
Part A
What is the total number of bright spots (indicating complete constructive interference) that will occur on a large distant screen? Solve this problemwithout finding the angles. (Hint: What is the largest that sinθ can be? What does this imply for the largest value of m?)
Express your answer as an integer.
Part B
What is the angle of the bright spot farthest from the center?
The total number of bright spots (indicating complete constructive interference) is 2,The angle of the bright spot farthest from the center is approximately 0.06 degrees
Part A:
The total number of bright spots can be found using the equation:
nλ = d(sinθ + sinθ')
where n is the order of the bright spot, λ is the wavelength of light, d is the distance between adjacent slits on the grating,
θ is the angle between the incident ray and the normal to the grating, and θ' is the angle between the diffracted ray and the normal to the grating.
For maximum constructive interference, sinθ = 1 and sinθ' = 1, which gives:
nλ = d(2)
n = 2d/λ
The largest value of n occurs when sinθ is maximized, which is when θ = 90 degrees. Therefore, the maximum value of n is:
nmax = 2d/λmax
Substituting the given values, we get:
nmax = 2(1/299 mm)/631 nm
nmax ≈ 2
Part B:
The angle of the bright spot farthest from the center can be found using the equation:
dsinθ = mλ
where d is the distance between adjacent slits on the grating, θ is the angle between the incident ray and the normal to the grating, m is the order of the bright spot, and λ is the wavelength of light.
For the bright spot farthest from the center, m = 1. The maximum value of sinθ occurs when θ = 90 degrees. Therefore, we have:
dsinθmax = λ
Substituting the given values, we get:
sinθmax ≈ λ/(d*m) ≈ 0.00105
Taking the inverse sine of this value, we get:
θmax ≈ 0.06 degrees
To know more about interference refer here :-
https://brainly.com/question/31857527#
#SPJ11
U-groove weld is used to butt weld two pieces of 7.0-mm-thick austenitic stainless steel plate in an arc welding operation. The U-groove is prepared using a milling cutter so the radius of the groove is 3.0 mm; however, during welding, the penetration of the weld causes an additional 1.5 mm of metal to be melted. Thus, the final cross-sectional area of the weld can be approximated by a semicircle with radius = 4.5 mm. The length of the weld = 250 mm. The melting factor of the setup = 0.65, and the heat transfer factor = 0.90. Assuming the resulting top surface of the weld bead is flush with the top surface of the plates, determine (a) the amount of heat (in joules) required to melt the volume of metal in this weld (filler metal plus base metal),Enter your answer
To find the heat required, calculate the volume of metal melted, multiply by the melting factor, specific heat, and heat transfer factor.
(a) First, find the volume of the weld:
- Cross-sectional area of the weld = (pi * [tex]4.5^{2}[/tex]) / 2 = 31.81 mm²
- Weld volume = Area * Length = 31.81 * 250 = 7952.5 mm³
Next, calculate the amount of heat required:
- Heat required = Volume * Melting Factor * Specific Heat * Heat Transfer Factor
Assuming a specific heat of austenitic stainless steel as 500 J/kgK and density as 8000 kg/m³:
- Convert volume to mass: Mass = Volume * Density = 7952.5 * [tex]10^{-9}[/tex] * 8000 = 0.06362 kg
- Heat required = 0.06362 * 0.65 * 500 * 0.9 = 16.52 kJ
The heat required to melt the volume of metal in this weld is approximately 16.52 kJ.
For more such questions on melting, click on:
https://brainly.com/question/20534573
#SPJ11
The amount of heat required to melt the metal in the U-groove weld is approximately 35,700 Joules, based on calculations involving volume, specific heat, and mass.
To determine the amount of heat required to melt the volume of metal in the U-groove weld, we can calculate the volume of the weld and then multiply it by the specific heat of the material.
The volume of the weld can be approximated as the volume of a cylinder with a semicircular cross-section. The formula for the volume of a cylinder is:
V = π * r^2 * h,
where V is the volume, r is the radius, and h is the height (length) of the weld.
Given:
Radius (r) = 4.5 mm = 0.0045 m
Length (h) = 250 mm = 0.25 m
Substituting the values into the volume formula:
V = π * [tex](0.0045 m)^2 * 0.25 m.[/tex]
Calculating this expression, we find:
V ≈ [tex]5.026 * 10^{(-6)} m^3.[/tex]
The specific heat (c) of austenitic stainless steel is approximately 500 J/(kg·°C).
To determine the mass of the metal in the weld, we need to consider the thickness and length of the weld.
The thickness of the stainless steel plate is 7.0 mm. Since the weld penetrates an additional 1.5 mm, the effective thickness is 8.5 mm = 0.0085 m.
The cross-sectional area (A) of the weld can be calculated as the area of the semicircle:
A = (π * [tex]r^2[/tex]) / 2.
Substituting the values:
A = (π * [tex](0.0045 m)^2) / 2[/tex].
Calculating this expression, we find:
A ≈ [tex]1.272 * 10^{(-5)} m^2.[/tex]
The mass (m) of the metal in the weld can be calculated by multiplying the density (ρ) of the stainless steel by the volume (V) and the cross-sectional area (A):
m = ρ * V * A.
The density (ρ) of austenitic stainless steel is approximately [tex]8000 kg/m^3.[/tex]
Substituting the values:
m ≈ [tex]8000 kg/m^3 * 5.026 * 10^{(-6)} m^3 * 1.272 * 10^{(-5)} m^2[/tex].
Calculating this expression, we find:
m ≈ 0.051 kg.
Finally, to calculate the amount of heat (Q) required to melt the metal in the weld, we can use the formula:
Q = m * c * ΔT,
where ΔT is the change in temperature, which is the melting point of the stainless steel.
The melting point of austenitic stainless steel is approximately 1400 °C.
Substituting the values:
Q ≈ 0.051 kg * 500 J/(kg·°C) * 1400 °C.
Calculating this expression, we find:
Q ≈ 35,700 J.
Therefore, the amount of heat required to melt the volume of metal in this U-groove weld is approximately 35,700 Joules.
To learn more about mass from the given link
https://brainly.com/question/86444
#SPJ4
a man walks 18m east then 9.5 north. what is the direction of his displacement? 62o 28o 242o 208o
(D) The direction of the displacement is 28.0 degrees
We can use trigonometry to find the direction of the displacement.
The displacement is the straight line distance between the starting point and ending point of the man's walk. To find the displacement, we can use the Pythagorean theorem:
displacement = sqrt(18^2 + 9.5^2) = 20.5 meters
The direction of the displacement is the angle between the displacement vector and the east direction. We can use the inverse tangent function to find this angle:
tan(theta) = opposite/adjacent = 9.5/18
theta = arctan(9.5/18) = 28.0 degrees
Therefore, the direction of the displacement is 28.0 degrees, which is closest to 28 degrees in the options provided.
For more such questions on displacement
https://brainly.com/question/14422259
#SPJ11
We can use the Pythagorean theorem and trigonometry to solve this problem.
The displacement of the man is the straight-line distance from his starting point to his ending point, which forms the hypotenuse of a right triangle with legs of 18 m and 9.5 m. Using the Pythagorean theorem, we find that the magnitude of his displacement is:
d = sqrt((18)^2 + (9.5)^2) = 20.5 m (rounded to one decimal place)
To find the direction of his displacement, we need to determine the angle that the displacement vector makes with respect to the eastward direction (which we can take as the positive x-axis). This angle can be found using trigonometry:
tan(theta) = opposite/adjacent = 9.5/18
theta = arctan(9.5/18) = 28.2 degrees (rounded to one decimal place)
Therefore, the direction of the man's displacement is 28 degrees north of east, which is approximately northeast.
So the answer is 28.
Learn more about Pythagorean theorem, here:
brainly.com/question/343682
#SPJ11
Two sources emit waves that are in phase with each other.What is the largest wavelength that will give constructive interference at an observation point 181 m from one source and 325 m from the other source?
Answer:
The largest wavelength that will give constructive interference at the observation point is 144 meters.
Explanation:
We can start by using the formula for the path difference, which is given by:
Δx = r2 - r1
where r1 and r2 are the distances from the two sources to the observation point.
For constructive interference to occur, the path difference must be an integer multiple of the wavelength λ, i.e., Δx = mλ, where m is an integer.
Substituting the given values, we get:
Δx = 325 m - 181 m = 144 m
For the largest wavelength that gives constructive interference, we want m to be as small as possible, i.e., m = 1. Therefore, we have:
λ = Δx / m = 144 m / 1 = 144 m
Therefore, the largest wavelength that will give constructive interference at the observation point is 144 meters.
To learn more about wavelength refer here:
https://brainly.com/question/13533093#
#SPJ11
how might the hook cause an experimental density that is too high
The hook's mass and volume can contribute to the experimental density, leading to inaccurately high results.
In an experiment measuring the density of an object, it is crucial to account for all factors that might affect the measurement. If a hook is used to suspend the object in a liquid, the hook's mass and volume may be inadvertently included in the calculations. This can lead to an overestimation of the object's actual density.
When calculating density, the formula used is density = mass/volume. If the hook's mass is not subtracted from the total mass measurement, the numerator in this equation will be too high. Similarly, if the hook displaces any of the liquid in the container, the volume measurement might also be affected, potentially increasing the denominator in the density equation. Both of these factors can contribute to an experimental density that is higher than the true value.
To avoid such errors, it is important to properly account for the hook's mass and volume during the experiment. This can be done by measuring the hook's mass separately and subtracting it from the total mass. Additionally, ensuring that the hook does not displace a significant amount of liquid can help prevent errors in volume measurement. By taking these precautions, you can obtain a more accurate experimental density.
To know more about density, click here;
https://brainly.com/question/29775886
#SPJ11
determine the wavelength of an x-ray with a frequency of 4.2 x 1018 hz
The wavelength of an x-ray with a frequency of 4.2 x 10^18 Hz is approximately 7.14 x 10^-11 meters.
To determine the wavelength of an x-ray with a frequency of 4.2 x 10^18 Hz, we can use the following equation:
wavelength = speed of light / frequency
The speed of light in a vacuum is approximately 3.00 x 10^8 meters per second.
Substituting the given frequency value into the equation, we get:
wavelength = (3.00 x 10^8 m/s) / (4.2 x 10^18 Hz)
Simplifying this expression gives:
wavelength = 7.14 x 10^-11 meters
Therefore, the wavelength of an x-ray with a frequency of 4.2 x 10^18 Hz is approximately 7.14 x 10^-11 meters.
Click the below link, to learn more about Wavelength of X-ray:
https://brainly.com/question/31417654
#SPJ11
If we put a charge in a box and enlarge the size of that box... a) the reading of the charge outside of the box will be constant. b) the electric flux, will increase. c) the electric potential will not equal zero inside the box. d) the electric field lines will decrease with distance. e) the electric potential inside of the box will be equal the flux. f) the size of the enclosed box does not matter.
The correct statement is d) the electric field lines will decrease with distance when a charge is placed in an enlarged box.
When a charge is placed inside a box and the size of the box is enlarged, the electric field lines will spread out and decrease in density with increasing distance from the charge. This is because the electric field intensity is inversely proportional to the square of the distance from the charge.
The other statements are incorrect: a) the reading of the charge outside the box depends on the distance and shielding; b) the electric flux remains constant due to Gauss's Law; c) the electric potential can be zero inside the box if it's a Faraday cage; e) the electric potential and flux are not equal; f) the size of the box can affect electric potential and field lines.
Learn more about Gauss's Law here:
https://brainly.com/question/14767569
#SPJ11
what is the minimum hot holding temperature for fried shrimp
The minimum hot holding temperature for fried shrimp is 135°F (57°C), as per the FDA Food Code, to prevent bacterial growth and ensure the food is safe to consume.
According to the FDA Food Code, potentially hazardous foods like shrimp should be hot held at a temperature of 135°F (57°C) or higher to prevent the growth of harmful bacteria. This temperature range ensures that the food remains safe for consumption and does not promote bacterial growth. Hot holding temperatures should be monitored regularly with a thermometer to ensure that the food stays within the safe temperature range. It is important to note that shrimp, like all seafood, is highly perishable and should be consumed within a few hours of cooking or placed in a refrigerator or freezer to prevent spoilage.
learn more about shrimp here:
https://brainly.com/question/28694514
#SPJ11
10-4. calculate the required diameter for certified-capacity liquid rupture discs for the following conditions. assume a liquid specific gravity of 1.2 for all cases. Liquid flow Set pressure Overpressure Backpressure a. 500 gpm b. 100 gpm c. 5 m/s d. 10 m/s 100 psig 50 psig 10 barg 20 barg 10 psig 5 psig 1 barg 2 barg 5 psig 2 psig 0.5 barg 1 barg
The required diameter for certified-capacity liquid rupture discs for the given conditions are 6.08 inches for 500 gpm, 3.07 inches for 100 gpm, 1.29 inches for 5 m/s, and 1.60 inches for 10 m/s.
To calculate the required diameter for certified-capacity liquid rupture discs for the given conditions, we first need to determine the burst pressure for each case. The burst pressure is calculated using the following formula:
Burst Pressure = Set Pressure + Overpressure - Backpressure
Using the specific gravity of 1.2 for all cases, we can calculate the burst pressure for each scenario as follows:
a. 500 gpm: Burst Pressure = 100 psig + 50 psig - 10 psig = 140 psig
b. 100 gpm: Burst Pressure = 100 psig + 50 psig - 5 psig = 145 psig
c. 5 m/s: Burst Pressure = 10 barg + 1 barg - 0.5 barg = 10.5 barg
d. 10 m/s: Burst Pressure = 20 barg + 2 barg - 1 barg = 21 barg
Once we have the burst pressure, we can use the specific gravity and the following formula to calculate the required diameter of the rupture disc:
Diameter = (Flow Rate * 60 * Specific Gravity) / (Burst Pressure * 0.8 * 3.14)
Where:
Flow Rate = Liquid flow in gallons per minute (gpm) or meters per second (m/s)
Specific Gravity = 1.2
Burst Pressure = Calculated burst pressure in psig or barg
Using the above formula, we can calculate the required diameter for each scenario as follows:
a. 500 gpm: Diameter = (500 * 60 * 1.2) / (140 * 0.8 * 3.14) = 6.08 inches
b. 100 gpm: Diameter = (100 * 60 * 1.2) / (145 * 0.8 * 3.14) = 3.07 inches
c. 5 m/s: Diameter = (5 * 60 * 1.2) / (10.5 * 0.8 * 3.14) = 1.29 inches
d. 10 m/s: Diameter = (10 * 60 * 1.2) / (21 * 0.8 * 3.14) = 1.60 inches
Therefore, the required diameter for certified-capacity liquid rupture discs for the given conditions are 6.08 inches for 500 gpm, 3.07 inches for 100 gpm, 1.29 inches for 5 m/s, and 1.60 inches for 10 m/s.
To know more about Specific gravity visit:
https://brainly.com/question/31485690
#SPJ11
Calculate the de Broglie wavelength of (a) a 0.998 keV electron (mass = 9.109 x 10-31 kg), (b) a 0.998 keV photon, and (c) a 0.998 keV neutron (mass = 1.675 x 10-27 kg). (a) Number Units (b) Number Units (c) Number Units
(a) The de Broglie wavelength of a 0.998 keV electron can be calculated using the formula λ = h / p, where λ is the wavelength, h is the Planck constant, and p is the momentum of the electron.
Plugging in the values, we get:
[tex]λ = h / p = h / √(2mE)[/tex]
where m is the mass of the electron, E is its energy, and h is the Planck constant.
Substituting the values, we get:
[tex]λ = 6.626 x 10^-34 J.s / √(2 x 9.109 x 10^-31 kg x 0.998 x 10^3 eV x 1.602 x 10^-19 J/eV)[/tex]
[tex]λ = 3.86 x 10^-11 m[/tex]
Therefore, the de Broglie wavelength of a 0.998 keV electron is 3.86 x 10^-11 meters.
(b) For a photon, the de Broglie wavelength can be calculated using the formula λ = h / p, where p is the momentum of the photon. Since photons have no rest mass, their momentum can be calculated using the formula p = E / c, where E is the energy of the photon and c is the speed of light.
Plugging in the values, we get:
[tex]λ = h / p = h / (E / c)[/tex]
[tex]λ = hc / E[/tex]
Substituting the values, we get:
[tex]λ = (6.626 x 10^-34 J.s x 3 x 10^8 m/s) / (0.998 x 10^3 eV x 1.602 x 10^-19 J/eV)[/tex]
λ = 2.48 x 10^-10 m
Therefore, the de Broglie wavelength of a 0.998 keV photon is 2.48 x 10^-10 meters.
(c) The de Broglie wavelength of a 0.998 keV neutron can be calculated using the same formula as for an electron: λ = h / p, where p is the momentum of the neutron. However, since the mass of the neutron is much larger than that of an electron, its de Broglie wavelength will be much smaller.
Plugging in the values, we get:
[tex]λ = h / p = h / √(2mE)[/tex]
Substituting the values, we get:
[tex]λ = 6.626 x 10^-34 J.s / √(2 x 1.675 x 10^-27 kg x 0.998 x 10^3 eV x 1.602 x 10^-19 J/eV)[/tex]
[tex]λ = 2.20 x 10^-12 m[/tex]
Therefore, the de Broglie wavelength of a 0.998 keV neutron is 2.20 x 10^-12 meters.
In summary, the de Broglie wavelength of a 0.998 keV electron is 3.86 x 10^-11 meters, the de Broglie wavelength of a 0.998 keV photon is 2.48 x 10^-10 meters, and the de Broglie wavelength of a 0.998 keV neutron is 2.20 x 10^-12 meters.
Learn more about Broglie wavelength here:
https://brainly.com/question/17295250
#SPJ11
if 7.052 a current is passing through a straight wire, what would be the magnetic field induced at a point 2 centimeter away from the wire? the answer is
The magnetic field induced at a point 2 centimeters away from the straight wire with a current of 7.052 A is approximately 7.03 × 10⁻⁵ T (Tesla).
To calculate the magnetic field induced at a point 2 centimeters away from a straight wire with a current of 7.052 A, we can use Ampere's Law. The formula for the magnetic field (B) around a straight wire is:
B = (μ₀ * I) / (2 * π * r)
where:
- B is the magnetic field strength
- μ₀ is the permeability of free space, which is approximately 4π × 10⁻⁷ Tm/A
- I is the current, in this case, 7.052 A
- r is the distance from the wire, in this case, 2 cm or 0.02 m
Now we can plug in the values into the formula:
B = (4π × 10⁻⁷ Tm/A * 7.052 A) / (2 * π * 0.02 m)
B = (28.12 × 10⁻⁷ Tm) / (0.04 m)
B = 7.03 × 10⁻⁵ T
So, the magnetic field induced at a point 2 centimeters away from the straight wire with a current of 7.052 A is approximately 7.03 × 10⁻⁵ T (Tesla).
To know more about Magnetic field refer here :
https://brainly.com/question/26051825
#SPJ11
a mineral originally contained 1,000 radioactive parents. after two half-lives have passed the mineral will contain parent atoms and daughter atoms. enter in the correct numerical values.
Answer:
N = N0 / 4
After 2 half-lives 1/4 of the original N0 will be present
250 - number of parent atoms left
750 - number of daughter atoms present
A proton moves along the x-axis with vx=1.0�107m/s.
a)
As it passes the origin, what are the strength and direction of the magnetic field at the (0 cm, 1 cm, 0 cm) position? Give your answer using unit vectors.
Express your answer in terms of the unit vectors i^, j^, and k^. Use the 'unit vector' button to denote unit vectors in your answer.
The magnetic field at the point (0 cm, 1 cm, 0 cm) is B = 0 i^ + 0 j^ + 1.6×10^-7 k^.
A proton moving along the x-axis with a velocity of 1.0×107m/s generates a magnetic field. At the position (0 cm, 1 cm, 0 cm), the strength and direction of the magnetic field can be determined using the right-hand rule. The direction of the magnetic field is perpendicular to both the velocity of the proton and the position vector at the point (0 cm, 1 cm, 0 cm).
Expressing the answer using unit vectors, the magnetic field can be written as B = Bx i^ + By j^ + Bz k^, where i^, j^, and k^ are unit vectors in the x, y, and z directions, respectively. The magnitude of the magnetic field is given by B = μ0qv/4πr2, where μ0 is the permeability of free space, q is the charge of the proton, v is the velocity of the proton, and r is the distance between the proton and the point (0 cm, 1 cm, 0 cm).
Using this formula, the strength of the magnetic field at the point (0 cm, 1 cm, 0 cm) can be calculated. The distance between the proton and the point is r = (1+0+0.01) cm = 0.01005 m. Plugging in the values, we get B = (4π×10^-7 Tm/A)(1.6×10^-19 C)(1.0×10^7 m/s)/(4π(0.01005 m)^2) = 1.6×10^-7 T.
The direction of the magnetic field can be determined using the right-hand rule. Since the velocity of the proton is in the positive x-direction, and the position vector is in the positive y-direction, the magnetic field must be in the positive z-direction.
To know more about the magnetic field, click here;
https://brainly.com/question/14848188
#SPJ11
A square-wave inverter supplies an RL series load with R=25 ohms and L=25mH. The output frequency is 120 Hz. (a) Specify the dc source voltage such that the load current at the fundamental frequency is 2.0 A rms. (b) Determine the THD of the load current (until 9), show all your work. + Vdc
(a) The dc source voltage is 61.2 V.
(b) The THD of the load current is approximately 33.2%.
(a) To calculate the dc source voltage required to produce a load current of 2.0 A rms, we first need to calculate the impedance of the load at the fundamental frequency. The impedance can be calculated as Z = R + jωL, where R is the resistance of the load, L is the inductance of the load, and ω is the angular frequency.
ω = 2πf
ω = 2π x 120 Hz
ω = 753.98 rad/s
Z = 25 + j(753.98 x 0.025)
Z = 25 + j18.85 Ω
The rms value of the load current is given by I = V/Z, where V is the rms value of the voltage supplied by the inverter.
I = 2.0 A rms, Z = 25 + j18.85 Ω
Therefore, V = IZ
V = (2.0 A rms) x (25 + j18.85 Ω)
V = 61.2 + j45.35 V rms
The dc source voltage is the average value of the voltage waveform, which is equal to the rms value multiplied by π/2.
Vdc = (π/2) x 61.2 V rms ≈ 96.2 Vdc
(b) The total harmonic distortion (THD) of the load current is a measure of the distortion of the current waveform from a perfect sinusoid. It is defined as the square root of the sum of the squares of the harmonic components of the current waveform, divided by the rms value of the fundamental component.
THD = √[(I2² + I3² + ... + In²)/I1²] x 100%
where I1 is the rms value of the fundamental component, and I2, I3, ..., In are the rms values of the second, third, ..., nth harmonic components.
For a square-wave inverter, the load current waveform contains only odd harmonic components. The rms value of the nth harmonic component can be calculated as
In = (4Vdc/(nπZ)) x sin(nπ/2)
where n is the harmonic number.
Using this equation, we can calculate the rms values of the first three harmonic components of the load current.
I1 = 2.0 A rms (given)
I3 = (4 x 96.2 Vdc / (3π x 25 Ω)) x sin(3π/2)
I3 ≈ 0.632 A rms
I5 = (4 x 96.2 Vdc / (5π x 25 Ω)) x sin(5π/2)
I5 ≈ 0.254 A rms
The THD can now be calculated as
THD = √[(0.632² + 0.254²)/2.0²] x 100%
THD ≈ 33.2%
To learn more about total harmonic distortion, here
https://brainly.com/question/30198365
#SPJ4
a solid disk of radius 9.00 cm and mass 1.15 kg, which is rolling at a speed of 3.50 m/s, begins rolling without slipping up a 13.0° slope. How long will it take for the disk to come to a stop?
The disk will come to a stop after 9.55 s.
The initial total mechanical energy of the disk is equal to the sum of its translational kinetic energy and its rotational kinetic energy. As the disk rolls up the incline, its gravitational potential energy increases while its mechanical energy decreases. When the disk comes to a stop, all of its mechanical energy has been converted into potential energy. The work-energy theorem can be used to relate the initial and final kinetic energies to the change in potential energy.
First, we need to find the initial mechanical energy of the disk:
Ei = 1/2mv² + 1/2Iω², where I = 1/2mr² for a solid diskEi = 1/2(1.15 kg)(3.50 m/s)² + 1/2(1/2)(1.15 kg)(0.09 m)²(3.50 m/s)/0.09 mEi = 2.542 JAt the top of the incline, the potential energy of the disk is equal to its initial mechanical energy:
mgh = Ei(1.15 kg)(9.81 m/s²)(0.09 m)(sin 13.0°) = 2.542 Jh = 0.196 mThe final kinetic energy of the disk is zero when it comes to a stop at the top of the incline. The work done by friction is equal to the change in kinetic energy:
W = ΔK = -Eiμkmgd = -Ei, where d = h/sin 13.0° is the distance along the inclineμk = -Ei/mgdsin 13.0°μk = -2.542 J/(1.15 kg)(9.81 m/s²)(0.196 m)/(sin 13.0°)μk = 0.291The frictional force is given by:
f = μkmg = (0.291)(1.15 kg)(9.81 m/s²)f = 3.35 NThe torque due to friction is given by:
τ = fr = (3.35 N)(0.09 m)τ = 0.302 N·mThe torque due to the net force (gravitational force minus frictional force) is given by:
τ = Iα = (1/2mr²)αα = (g sin 13.0° - f/r)/(1/2r)α = (9.81 m/s²)(sin 13.0°) - (3.35 N)/(0.09 m)/(1/2)(0.09 m)α = 4.25 rad/s²The angular velocity of the disk at any time t is given by:
ω = ω0 + αtThe linear velocity of the disk at any time t is given by:
v = rωThe distance traveled by the disk at any time t is given by:
d = h + x = h + vt - 1/2at²At the instant the disk comes to a stop, its final velocity is zero. We can use the above equations to solve for the time it takes for the disk to come to a stop:
v = rω = 0ω = 0t = -ω0/αt = -3.50 m/s/(0.09 m)(4.25 rad/s²)t = 9.55 sTo learn more about rolling speed, here
https://brainly.com/question/14212372
#SPJ4
A photon of initial energy 0.1 MeV undergoes Compton scattering at an angle of 60°. Find (a) the energy of the scattered photon, (b) the recoil kinetic energy of the electron, and (c) the recoil angle of the electron.
The energy of the scattered photon is E₁ = E₀ - ΔE = 0.1 MeV - 0.042 MeV = 0.058 MeV. The recoil kinetic energy of the electron is given by: K = (0.042 MeV)/(1 + (0.1 MeV/(0.511 MeV/c²))) = 0.013 MeV. The recoil angle of the electron is φ = cos⁻¹(0.707) = 45°.
The energy of the scattered photon can be calculated using the formula: ΔE = E₀ - E₁ = E₀ * [1 - cos(θ)] where E₀ is the initial energy of the photon, E₁ is the energy of the scattered photon, and θ is the angle of scattering. Substituting the given values, we get ΔE = 0.1 MeV * [1 - cos(60°)] = 0.042 MeV.
The recoil kinetic energy of the electron can be calculated using the formula: K = (ΔE)/(1 + (E₀/m₀c²)), where K is the recoil kinetic energy of the electron, ΔE is the change in energy of the photon, E₀ is the initial energy of the photon, m₀ is the rest mass of the electron, and c is the speed of light. Substituting the given values, we get K = (0.042 MeV)/(1 + (0.1 MeV/(0.511 MeV/c²))) = 0.013 MeV.
The recoil angle of the electron can be calculated using the formula: cos(φ) = [1 + (E₀/m₀c²)]/[(E₀/m₀c²) * (1 - cos(θ)) + 1], where φ is the angle of recoil of the electron. Substituting the given values, we get cos(φ) = [1 + (0.1 MeV/(0.511 MeV/c²))]/[(0.1 MeV/(0.511 MeV/c²)) * (1 - cos(60°)) + 1] = 0.707.
To know more about kinetic energy, refer here:
https://brainly.com/question/30764377#
#SPJ11