Discuss the nature of materials causing turbidity in

(a) River water during flash flood ​​​​​

(b) Polluted river water ​​​​​

(c) Domestic wastewater

Answers

Answer 1

Answer:

a

Explanation:

Answer 2
A if not B i believe

Related Questions

QUESTION 6
Which of the following is NOT a resume format?
01. Chronological
O2. Portfolio
3. Functional
04. Combination

Answers

It would be 2 Portfolio

Construct the plane-stress yield envelopes in a principle stress space for both the Tresca and the von Mises yield theories using your calculated value of the yield strength to scale the envelopes. Indicate the two equivalent load paths corresponding to pure shear on the yield envelopes. Calculate the shear yield strength of Al 6061-T6 aluminum predicted by the above theories.

Answers

Answer:

Explanation:

The missing part of the question is attached in the diagram below, the second diagram shows the schematic view of the stress-strain curve and the plane stress.

From the given information:

The elastic modulus is:

[tex]E = \dfrac{\sigma}{\varepsilon} \\ \\ E = \dfrac{150 \ MPa}{0.0217} \\ \\ E = 69.124 \ GPa[/tex]

Hence, suppose 0.2% offset cuts the stress-strain curve at a designated point A from the image attached below, then the yield strength relating to the stress axis from the curve will be [tex]\sigma_y[/tex] = 270 MPa.

The shear yield strength by using von Mises criteria is estimated as;

[tex]\tau_1 = \dfrac{\sqrt{2}}{3}\sigma_y \\ \\ \tau_1 = \dfrac{\sqrt{2}}{3}*270 \\ \\ \tau_1 = 127.28 \ MPa[/tex]

The shear yield strength by using Tresca criteria is:

[tex]\tau_2 = \dfrac{1}{2}\sigma_y \\ \\ \tau_2= \dfrac{1}{2}*270 \\ \\ \tau_2 = 135 \ MPa[/tex]

A cylindrical 1045 steel bar is subjected to repeated compression-tension stress cycling along its axis. If the load amplitude is 22,000 N (4950 lbf), compute the minimum allowable bar diameter to ensure that fatigue failure will not occur. Assume a factor of safety of 2.0

Answers

Answer:

13.4 mm

Explanation:

Given data :

Load amplitude ( F )  = 22,000 N

factor of safety ( N )= 2.0

Take ( Fatigue limit stress amplitude for this alloy ) б = 310 MPa

calculate the minimum allowable bar diameter to ensure that fatigue failure will not occur

minimum allowable bar diameter = 13.4 * 10^-3 m ≈ 13.4 mm

attached below is a detailed solution

How does distribution add value to goods and services being sold,
including intellectual property?

Answers

Answer:

Distribution (or its more sophisticated counterpart, supply chain management) can add value to goods and services by making them more easily and conveniently available to consumers. ... This means that you need good wholesalers and good transportation systems to get your products to the retailers.

Explanation:

Distribution (or its more sophisticated counterpart, supply chain management) can add value to goods and services by making them more easily and conveniently available to consumers. ... This means that you need good wholesalers and good transportation systems to get your products to the retailers.

Answer:

Distribution (or its more sophisticated counterpart, supply chain management) can add value to goods and services by making them more easily and conveniently available to consumers.

Explanation:

hope it helps <33

You are working as an electrical technician. One day, out in the field, you need an inductor but cannot find one. Looking in your wire supply cabinet, you find a cardboard tube with single-conductor wire wrapped uniformly around it to form a solenoid. You carefully count the turns of wire and find that there are 570 turns. The diameter of the tube is 8.10 cm, and the length of the wire-wrapped portion is 35.0 cm. You pull out your calculator to determine the following.

a. the inductance of the coil (in mH)
b. the emf generated in the coil if the current in the wire increases at the rate of 3.00 A/s (Enter the magnitude in mV.)

Answers

Answer:

a) the inductance of the coil is 6 mH

b) the emf generated in the coil is 18 mV  

Explanation:

Given the data in the question;

N = 570 turns

diameter of tube d = 8.10 cm = 0.081 m

length of the wire-wrapped portion l =  35.0 cm = 0.35 m

a) the inductance of the coil (in mH)

inductance of solenoid

L = N²μA / l

A = πd²/4  

so

L = N²μ(πd²/4) / l

L = N²μ(πd²) / 4l

we know that μ = 4π × 10⁻⁷ TmA⁻¹

we substitute

L = [(570)² × 4π × 10⁻⁷× ( π × (0.081)² )] / 4(0.35)

L =  0.00841549 / 1.4

L = 6 × 10⁻³ H    

L = 6 × 10⁻³ × 1000 mH

L = 6 mH

Therefore, the inductance of the coil is 6 mH

b)

Emf ( ∈ ) = L di/dt

given that; di/dt = 3.00 A/sec

{∴ di = 3 - 0 = 3 and dt = 1 sec}

Emf ( ∈ ) = L di/dt

we substitute

⇒ 6 × 10⁻³ ( 3/1 )

= 18 × 10⁻³ V

= 18 × 10⁻³ × 1000

= 18 mV  

Therefore, the emf generated in the coil is 18 mV  

Which one of the following answer options are your employers responsibility

Answers

Where are your answer options?

Answer:

Implement a hazard communication program

Explanation: i took the quiz

The yield stress of a steel is 250Mpa. A steel rod used for implant in a femurneeds to withstand 29KN. What should the diameter of the rod be not to deform

Answers

Answer:

r = 1.922 mm

Explanation:

We are given;

Yield stress; σ = 250 MPa = 250 N/mm²

Force; F = 29 KN = 29000 N

Now, formula for yield stress is;

σ = F/A

A = F/σ

Where A is area = πr²

Thus;

r² = 2900/250π

r² = 3.6924

r = √3.6924

r = 1.922 mm

4. What element is missing from construction drawings?
A. Physical arrangement of specific electrical equipment
B. Electrical layout
C. Electrical connections
D. Side elevation views

Answers

Answer:

C Electrical Connections

Explanation:

In reading says . However, electrical

connections aren’t shown in construction drawings.

An array of eight aluminum alloy long fins, each 3 mm wide, 0.4 mm thick, and 40 mm long, is used to cool a transistor. When the base is at 340 K and the ambient air is at 300 K, how much power do they dissipate if the combined convection and radiation heat transient coefficient is estimated to be 8 W/m2K? The alloy has a conductivity of 175 W/mKand the heat transfer from the tip is negligible.

Answers

Answer:

0.08704 W

Explanation:

converting the mm to m (1000mm = 1m)

cross-sectional area of the fins, Ac = (0.003) (0.0004) = 0.0000012‬m^2

The wetted perimeter of the cross-section, P = 2 (0.003 + 0.0004) = 0.0068‬m

Thickness of solid in direction of heat flow, B^2 = (heat transient coefficient, h) (The wetted perimeter of the cross-section, P) ÷ (Thermal conductivity, k) (cross-sectional area of the fins, Ac)

B^2 = (8 W/m2K)(0.0068‬m) ÷ (175 W/mK)(0.0000012‬m^2)

=259.0476m^-2

B= square root of the result

B = 16.09m^-1

we now look for:

The Coordinate, x = B, multiplied by Length, L

x = (16.09m^-1) (0.04m) = 0.6436‬

 finding the side area of a fin =  P multiplied by Length, L

= 0.0068‬m X 0.04m = 0.000272m^2

Neglecting inefficiency, assuming the fins are all 100% efficient, the power they would dissipate =

h, Heat-transfer coefficient (PL) (temperature of at the base - temperature at the ambient air)

= (8) (0.000272m^2)(340 K- 300k)

= 0.08704 W

A 4 stroke over-square single cylinder engine with an over square ratio of 1.1,the displacement volume of the engine is 245cc .The clearance volume is 27.2cc the bore of this engine is ?

Answers

Answer:

10.007

Explanation:

Assuming we have to find out the compression ratio of the engine

Given information

Cubic capacity of the engine, V = 245 cc

Clearance volume, V_c = 27.2 cc

over square-ratio = 1.1

thus,

D/L = 1.1

where,

D is the bore

L is the stroke

Now,

Volume of the engine V =[tex]\frac{\pi}{4} D^2L[/tex]

plugging values we get

245 = [tex]\frac{\pi}{4} D^3/1.1[/tex]

Solving we get D =7 cm

therefore,  L= 7/1.1 =6.36 cm

Now,

the compression ratio is given as:

r =(V+V_c)/V_c

on substituting the values, we get

r = (245+27.2)/27.2 =10.007

Hence, Compression ratio = 10.007

what's nested piezometer? ​

Answers

Explanation:

Nested piezometers indicate an upward flow if the elevation of the top of the water in the piezometer tube that penetrates the aquifer to the deeper point is greater than the elevation of the water in the shallower tube

Leland wants to work in a Production career operating heavy machinery. Which type of education or training should Leland seek?

a bachelor’s degree then a master’s degree
vocational school certificate or master’s degree
on-the-job training or vocational school certificate
associate’s degree then a bachelor’s degree

Answers

Answer:

it is indeed C

Explanation:

Answer:

c

Explanation:

A 5-m-long, 4-m-high tank contains 2.5-m-deep water when not in motion and is open to the atmosphere through a vent in the middle. The tank is now accelerated to the right on a level surface at 2 m/s2. Determine the maximum gage pressure in the tank. Mark that point at the interior bottom of the tank. Draw the free surface at this acceleration.

Answers

Answer: hello your question lacks the required diagram attached below is the diagram

answer :  29528.1  N/m^2

Explanation:

Given data :

dimensions of tank :

Length = 5-m

Width = 4-m

Depth = 2.5-m

acceleration of tank = 2m/s^2

Determine the maximum gage pressure in the tank

Pa ( pressure at point A )  = s*g*h1

    = 10^3 * 9.81 * 3.01

    = 29528.1  N/m^2

attached below is the remaining part of the solution

How do you explain the application of regulations in locations containing baths, showers and electric floor heating, including the requirements needed?

Answers

Answer:

The application of regulations in locations are very important.

Explanation:

The application of regulations in locations are very important in order to gain more benefit from it because people choose those places that are well regulated and having more facilities. If the location has baths, showers, electric floor heaters and other necessities so the people prefer the place over another and increase of clients occurs which give more benefits to the place owners.

The aluminum rod (E1 = 68 GPa) is reinforced with the firmly bonded steel tube (E2 = 201 GPa). The diameter of the aluminum rod is d = 25 mm and the outside diameter of the steel tube is D= 45 mm. The length of the composite column is L = 761 mm. A force P = 88 kN is applied at the top surface, distributed across both the rod and tube.


Required:
Determine the normal stress σ in the steel tube.

Answers

Answer:

Explanation:

From the information given:

[tex]E_1 = 68 \ GPa \\ \\ E_2 = 201 \ GPa \\ \\ d = 25 \ mm \ \\ \\ D = 45 \ mm \ \\ \\ L = 761 \ mm \\ \\ P = -88 kN[/tex]

The total load is distributed across both the rod and tube:

[tex]P = P_1+P_2 --- (1)[/tex]

Since this is a composite column; the elongation of both aluminum rod & steel tube is equal.

[tex]\delta_1=\delta_2[/tex]

[tex]\dfrac{P_1L}{A_1E_1}= \dfrac{P_2L}{A_2E_2}[/tex]

[tex]\dfrac{P_1 \times 0.761}{(\dfrac{\pi}{4}\times .0025^2 ) \times 68\times 10^4}= \dfrac{P_2\times 0.761}{(\dfrac{\pi}{4}\times (0.045^2-0.025^2))\times 201 \times 10^9}[/tex]

[tex]P_1(2.27984775\times 10^{-8}) = P_2(3.44326686\times 10^{-9})[/tex]

[tex]P_2 = \dfrac{ (2.27984775\times 10^{-8}) P_1}{(3.44326686\times 10^{-9})}[/tex]

[tex]P_2 = 6.6212 \ P_1[/tex]

Replace [tex]P_2[/tex] into equation (1)

[tex]P= P_1 + 6.6212 \ P_1\\ \\ P= 7.6212\ P_1 \\ \\ -88 = 7.6212 \ P_1 \\ \\ P_1 = \dfrac{-88}{7.6212} \\ \\ P_1 = -11.547 \ kN[/tex]

Finally, to determine the normal stress in aluminum rod:

[tex]\sigma _1 = \dfrac{P_1}{A_1} \\ \\ \sigma _1 = \dfrac{-11.547 \times 10^3}{\dfrac{\pi}{4} \times 25^2}[/tex]

[tex]\sigma_1 = - 23.523 \ MPa}[/tex]

Thus, the normal stress = 23.523 MPa in compression.


Forces always act in equal and opposite pairs

Answers

You are correct forces always act in the equal of opposite pairs

Air at 25 m/s and 15°C is used to cool a square hot molded plastic plate 0.5 m to a side having a surface temperature of 140°C. To increase the throughput of the production process, it is proposed to cool the plate using an array of slotted nozzles with width and pitch of 4 mm and 56 mm, respectively, and a nozzle-to-plate separation of 40 mm. The air exits the nozzle at a temperature of 15°C and a velocity of 10 m/s.

Required:
a. Determine the improvement in cooling rate that can be achieved using the slotted nozzle arrangement in lieu of turbulated air at 10 m/s and 15°C in parallel flow over the plate.
b. Would the heat rates for both arrangements change significantly if the air velocities were increased by a factor of 2?
c. What is the air mass rate requirement for the slotted nozzle arrangement?

Answers

Answer:

a. 2.30

b. decreases with increasing velocity.

c. 0.179 kg/s.

Explanation:

Without mincing let's dive straight into the solution to the question above.

                                                         [a].

The improvement in cooling rate that can be achieved using the slotted nozzle arrangement in lieu of turbulated air at 10 m/s and 15°C in parallel flow over the plate can be determined by calculating turbulent flow:

The turbulent flow over the plate= 10 × 0.5/ 20.92 × 10⁻6 = 2.39 × 10⁵.

While the turbulent flow correlation = 0.037( 2.39 × 10⁵)^[tex]\frac{4}{5}[/tex] (0.7)^[tex]\frac{1}{3}[/tex] = 659.6.

Array of slot noozle = [10 × (2  × 0.004)]/ 20.92  × 10^-6] = 3824.

where A = 4/56 =0.714.

And Ar = [ 60 + 4 (40/2  × 4) - 2 ]^2 ]-1/2 = 0.1021.

N = 2/3 (0.1021)^3/4 [ 2  ×  3824/ ( 0.0714 / 0.1021) + (.1021/0.0714)] (0.700)^0.42 =24.3.

h = 24.3  ×  0.030/0.004 = 91.1 W/m^2k.

Therefore; 659.6  × 0.030/0.5 = 39.0 W/m²k.

The turbulent flow = 0.5 × 39.6 × 0.5( 140 -15) = 1237.5 W.

The slot noozle = 91.1  ×  0.5  ×  0.5 [ 140 -15] = 2846.87W.

The improvement in cooling rate = 2846.87/ 1237.5 = 2.30.

                                                     [b].

2.3 [ (2^2/3)/ 2^4/5] = 2.1

Thus, it decreases with increasing velocity

                                                      [c].

The  air mass rate requirement for the slotted nozzle arrangement = 9 × 0.995 (0.5 × 0.004)10 = 0.179 kg/s.

Poly(cis-1,4-isoprene), or natural rubber (NR), has a tendency crystallize. The Tm of this polymer is slightly below room temperature, although lightly-crosslinked NR can partially crystallize at room temperature when stretched. Apparently, Tm is elevated upon stretching which allows for crystallization above the Tm of the unstretched polymer. Explain.

Answers

Answer:

Explanation:

Crystalline melting temperature (Tm) is termed as the temperature required for a  crystalline polymer to change to a fluid or glasslike crystalline spaces of a semi-crystalline polymer liquefy (expanded sub-atomic movement).  

Crystallization of polymers is an interaction related with incomplete arrangement of their atomic and molecular chains. These chains crease together and structure requested districts called lamellae, which form bigger spheroidal designs named spherulites. Polymers can solidify after cooling from melting, mechanical extending, or dissolvable dissipation. Crystallization influences the optical, mechanical, and synthetic chemical properties of the polymer.  

For a crystalline polymer, a required polymer chain is present in or goes along a few crystalline and amorphous zones. The crystalline zones are comprised of intermolecular & intramolecular arrangements or deliberate and thus firmly stuffed plan of atoms or chain fragments, and an absence of it brings about the development of amorphous zones.  

The mechanical property boundary, for example, shear modulus expansions in the temperature of perception for polymer material framework.  

The temperature reaction of direct linear polymers might be seen as partitioned into three particularly separate fragments:  

1. Above Tm: The polymer stays as fluid whose consistency & viscosity would rely upon atomic molecular weight and temperature.  

2. Between Tm and Tg: This area may go between close to 100% crystalline & 100% amorphous chain atomic bunches relying upon the polymer underlying consistency. The amorphous part carries on similar to supercooled fluid in this section. The generally actual conduct of the polymer in this moderate portion is similar to an elastic rubber.  

3.Below Tg: The polymer material saw as glass is hard and inflexible, showing and emanating a predetermined coefficient of thermal extension. The glass is more like a crystalline strong than the fluid in personal conduct standard regarding mechanical property boundaries. In regard to the molecular atomic request, in any case, the glass all the more intently takes after the fluid. There is little contrast between the direct linear and cross-connected polymer beneath Tg.

electrical engineering​

Answers

Answer:

Electrical engineering is an engineering discipline concerned with the study, design and application of equipment, devices and systems which use electricity, electronics, and electromagnetism.

Explanation:

What two units of measurement are used to classify engine sizes?

Answers

liters or cubic inches
metric units of cubic centimetres or litres

Where do greywater pipes generally feed into?
-Vent stack
-Water heater
-Waste stack
-Main supply

Answers

Answer:

c   Waste stack

Explanation:

Other Questions
What is the mean for this list of numbers? 19, 22, 24, 45 A blood sample has 50,000 bacteria present. a drug fights the bacteria such that every hour the number of bacteria remaining, r(n), decreases by half. If r(n) is an exponential function of the number, n, of hours since the drug was taken, find the bacteria present four hours after administering the drug. A CBC shows the numbers of each type of blood cell. Why would this test not be able to detect carbon monoxide poisoning? Francisco, Valeria y yo a Chicago el sbado. need help pls pls pls pls Which of the following best describes a population?A. All of the seagulls that live along the coastB. All of the seagulls that live along the coast, the fish they eat, and the waterC. All of the seagulls that live along the coast and the fish they eatD. All of the seagulls that live along the coast, as well as the sand and the water Bailey stood in line for hours and purchased the new game system the day it became available for $600. Knowing that there was a high demand for the game system and a limited supply, she decided to put the item on E-bay rather than keep it. She sold it for $950. She also sold her five-year old car for $5,000. She had purchased the car for $13,000. What is the taxable nature of these transactions? Multiple choice question. Bailey has a taxable short-term capital gain of $350 and a deductible long-term capital loss. Bailey has no tax consequences for these transactions because the assets sold were "personal use" assets. Bailey has a taxable short-term capital gain of $350, but no deductible loss for the car. Bailey does not have to pay tax on the game system, but she deductible long-term capital loss. Find(1) The total surface area of a closed cylindrical petrol storage tank whose diameter4.2 m. and height 4.5 m.(i) How much steel sheet was actually used, if 1/12of the steel was wasted in makingof the tank. (anewer quickly and steps in order ) what was one way in which Portuguese and Spanish colonies similar Write the unit rate for the following. a) kate sews 100 dresses In a 20 day month.b) Kim runs 5km in 30 minutes. Inspired by zoom, you want to determine whether there are significant differences in the satisfaction of couples that had their first date in person vs. couples who had their first date virtually. Based on the following satisfaction data (larger values indicate greater satisfaction), conduct an independent samples t-test using (alpha=.01) and an pooled variance. Is there a significant difference?Virtual Date In person date X= 23.76 X= 34.54 s2 = 123.43 s2 = 105.65 n = 5 n = 20A) Write the null and alternative hypotheses in symbolsB) What is your critical value?C) What's your pooled variance?D) What's your standard error?E) What's your obtained t? Halp ;-;I'll mark brainliestWhat are some of the achievements of the Gupta Empire that still affect society today? Discuss contributions made in mathematics, science, and medicine. Can someone help? Please? Help me y'all i really need help Which of the following describes positive feedback?Select one:A. A loss of output from the bodys receptors.B. The response of the body to increased temperatures.C. An event that reduces the effects of a stimulus.D. An event that enhances the original stimulus. Find the unknown length x in the right triangle, to the nearest tenth.D26F55E What is the length for x define futures contract. A form of government in which the citizens elect leaders and rule by majority.PLSS I NEED THIS ANSWERED NOW!! What is the percent change from 35 to 63? Indicate whether it is a percent increase or decrease. Explain hoy slanters can be negative ?