Answer:
133225
Explanation:
Suppose the coefficient of static friction is 0.55 rather than 0.61. is the weight of the pail and sand necessary to start the pumpkin moving in this case greater than, less than or equal to 11 N? calculate the required weight.
The weight of the pail and sand necessary to start the pumpkin moving in this case is less than 11 N.
What is the force of friction acting the pumpkin?The force of friction acting on the pumpkin depends on the weight of the pumpkin and the coefficient of static friction.
F = μW
where;
μ is the coefficient of static frictionW is the weight of the pumpkinThe weight of the pumpkin is calculated as follows;
W = mg
where;
m is the mass of the pumpkin = 1.8 kgg is acceleration due to gravityW = 1.8 kg x 9.8 m/s²
W = 17.64 N
The static friction force preventing the pumpkin from moving is calculated as follows;
F = μW
F = 0.55 x 17.64 N
F = 9.7 N
Thus, the minimum force required to move the pumpkin is 9.7 N which is less than 11 N.
Learn more about static friction force here: https://brainly.com/question/13680415
#SPJ1
The complete question is blow:
Suppose the coefficient of static friction is 0.55 rather than 0.61. is the weight of the pail and sand necessary to start the pumpkin moving in this case greater than, less than or equal to 11 N? calculate the required weight. mass of the pumpkin is 1.8 kg.
If you wanted the block to remain in the center of the table what masses of blocks would you add and where? Use the letters going around the table to identify their locations and tell me the mass you would make the block at that location (for example Point B 6000g)
Answer:
The work done is twice as great for block B because it is moved twice the ... Equal forces are used to move blocks A and B across the floor. ... Does the normal force of the floor pushing upward on the block do any work? ... Suppose that the mass is halfway between one of the extreme points of its motion and the center point.
Explanation:
Disadvanlayes and advantager of the and A and B
Answer:
Advantages
If there is a fault in one of the electric appliances, the current is able to pass through different paths of the circuit.
Disadvantages
In parallel circuits, we cannot increase the voltage since the resistance decreases in the parallel circuit.
Explanation:
A 23cm hammer is used to pull a nail. If 42.5 N of force is applied to it at a 45° angle, how much torque is applied?
Answer:6.91 Nm
Explanation:
Calculate the gravitational pull between the Earth and the Moon
Answer:
F = 1.99 10²⁰ N
Explanation:
The gravitational attraction is given by the expression
F = [tex]G \ \frac{m_1m_2}{r^2}[/tex]
where G is the constant of attraction 6.67 10⁻¹¹ N m²/kg²
in this case the bodies are the Earth and the Moon
let's calculate
F = [tex]6.67 \ 10^{-11} \ \frac{ 7.36 \ 10^{22} \ 5.98 \ 10^{24} }{ (3.84 \ 10^8)^2}[/tex].67 10⁻¹¹ 7.36 10 22 5.98 1024 / (3.84 108) 2
F = 1.99 10²⁰ N
A 0.17 kg ball on a 0.70 m string rotates in a circular path in a vertical plane. If the angular speed of the ball at the bottom of the circle is 7.0 rad/s, what is the force that maintains circular motion?
A. 5.6 N
B. 7.5 N
C. 1.7 N
D. 1.2 N
sun *
a.) the hunter
b.) Pole Star
c.) little bear
d.) pattern of stars
e.) nearest star
Plz help :> <3
Answer:
E
Explanation:
How are particles behaving in solid vs gas when it comes to sound?
Answer:
Sound waves have to travel through solids, gases, and liquids. Sound waves vibrate through the air in matter. Molecules in solids are packed tightly. This allows sound to travel faster through a solid than gas.
A cube measures 2.5 cm in height and has a density of 3.0 g/cm³. What is the mass?
Answer: mass: 46.875 g
Explanation:
[tex]density = \frac{mass}{volume}[/tex]
density = 3.0 g/cm^3
volume (lwh are all 2.5 since it is a cube) = 2.5^3 = 15.625
mass = ?
[tex]3 = \frac{mass}{15.625}[/tex]
mass = 3*15.625 = 46.875
What happens when weathering and erosion work together?
A. New mountains are created
B. The climate changes overnight
C. Metal objects become rusty
D. They change the earths surface
Plssss help
Answer:
A. New mountains are created
17. The four points built into the camera to ensure that each exposure can be oriented
to the camera calibration are called?
A.
Nodal points
B.
Focal points
C. Focus
D. Fiducial marks
E. None of the above
O
Rnd
STAT 1
MATRIX
4
CONST
7
RCL
召
STO
SOLVE
DE OLI
CALC
00
SHIFT
ENG
SS
ya
TCMPLX)
2
SVECTOR
NATURAL-V.P.A.M.
fx-991ES PLUS
CASIO
ALPHA
Ran# Ranlnt I
5
)
ANO
8
0999
Bl Abs
i
th
7.
hyp
X1
ГВА.
Solve for x in the diagram below.
(4.2 + 50°
150
T =
Answer:
x = 25
Explanation:
Find the diagram attached
From the diagram,
4x + 50 = 150 (vertically opposite angle)
4x = 150 - 50
4x = 100
x = 100/4
x =25
Hence the value of x is 25
Why do other stars look much dimmer than the sun?
Weight is the amount of matter in an object.
True or False
Answer:
False
Explanation:
The mass of an object is normally known as the weight of the object. but mass is the amount of matter in the object. Weight is the force exerted on an object by gravity
Answer: False
Explanation: mass is the amount of matter in an object
When conducting research,
are unintentional factors that creep into your experiment and have the potential to affect or even spoil your results.
a. confounding variables
b. replication digits
c. extrapolating factors
d. independent variables
Answer:
a. confounding variables.
Explanation:
An experiment can be defined as an investigation which typically involves the process of manipulating an independent variable (the cause) in order to be able to determine or measure the dependent variable (the effect).
This ultimately implies that, an experiment can be used by scientists to show or demonstrate how a condition causes or gives rise to another i.e cause and effect, influence, behavior, etc in a sample.
In an experiment , the variable being manipulated by an experimenter is known as an independent variable while the dependent variable is the event expected to change when the independent variable is manipulated.
A confounding variable can be defined as a variable that generally influences both the independent and dependent variable in an experiment or research study. Thus, it creates an association between the two variables in an experiment.
Hence, when conducting research, confounding variables are unintentional factors that creep into your experiment and have the potential to affect or even spoil your results.
What are three common fossil fuels?
A. coal, oil, natural gas
B. iron, lead, carbon
C. coal, gold, silver
D. solar, wind, water
Answer:
A. coal, oil, natural gas
Explanation:
this is because those three are related to fossil fuels.
Answer:
A:Coal,Oil,Natural gas
Explanation:
that pfp tho
While hammering a nail, you put in 30 Joules of work. The hammer then puts out 10 J of
work on the nail. What is that hammer's efficiency?
A. 300%
B. 40%
С. 33%
D. 33 J
Answer:
C Don't worry if you thought it was D. I almost answered that.
Explanation:
Remark
You can get this just by learning the vocabulary.
Efficiency = Work Out / Work In * 100%
Work in = 30J That's you swinging the hammer.
Work out = 10 J That's how much of the hammer's work gets to the nail.
Efficiency = (10/30)*100
Efficiency = 1/3 * 100
Efficiency = 33%
Answer:
I think its 40%, pls correct me if I am wrong :(
Explanation:
state the particles of matter
Answer:
Matter can exist in one of three main states: solid, liquid, or gas. Solid matter is composed of tightly packed particles. A solid will retain its shape; the particles are not free to move around. Liquid matter is made of more loosely packed particles.
2. The motion of roller coasters depends upon the conversion of potential
and kinetic energy. A 200 kg car starts from rest at the top of a hill with a
height of 30 m.
Which of the following is this car's kinetic energy at the bottom of the hill?
Answer:
58,800 Joules
Explanation:
I used the formula for Potential energy which is PE = mgh
200 kg x 9.8 m/s^2 x 30 m = 58,800 J
At the very tops of the rollercoaster is maximum PE which is 58,800 J and 0 J of KE, but at the very bottom is maximum KE (kinetic energy) which is 58,800 Joules but 0 J of PE. This is because energy can not be destroyed ONLY converted
Which of the following characteristics indicates a high level of adaptability to change over
time?
A. Needs routines that stay the same
OB. Insists on doing things her own way
C. Not easily influenced by peer pressure
OD. Open to new ideas and experiences
convertion of unit 8.28x10^-2ft m
Answer:
yes
Explanation:
no
A 3000-N force gives an object an acceleration of 15 m/s2. The mass of the object is
200 kg
General Formulas and Concepts:Math
Pre-Algebra
Order of Operations: BPEMDAS
Brackets Parenthesis Exponents Multiplication Division Addition Subtraction Left to RightEquality Properties
Multiplication Property of Equality Division Property of Equality Addition Property of Equality Subtraction Property of EqualityPhysics
Newton's Law of Motions
Newton's 1st Law of Motion: An object at rest remains at rest and an object in motion stays in motion
Newton's 2nd Law of Motion: F = ma (Force is equal to [constant] mass times acceleration)
Newton's 3rd Law of Motion: For every action, there is an equal and opposite reaction
Explanation:Step 1: Define
[Given] F = 3000 N
[Given] a = 15 m/s²
[Solve] m = x kg
Step 2: Solve for m
Substitute in variables [Newton's Second Law of Motion]: 3000 N = m(15 m/s²)[Mass] [Division Property of Equality] Isolate m [Cancel out units]: 200 kg = m[Mass] Rewrite: m = 200 kgHow is Newtons second law apply to the egg drop ?
Answer:
Newton's Second Law is applied because of the acceleration caused by natural forces as the egg is plummeting to the earth. And the amount of acceleration the egg has will be largely affected by the amount of force Mr. Baker uses to hurl the egg to the ground.
Explanation:
hope that helps
In some areas, hydroelectric power is not geographically appropriate and a different renewable energy source would be a better option. A conservation group is looking for renewable energy sources other than hydroelectric energy that could be used to generate electricity in grassland ecosystems, such as in the midwestern United States or in a savanna in Africa.
Required:
a. Propose a different renewable resource to use that would be a realistic solution to generating electricity without using fossil fuels or hydroelectric power in a grassland ecosystem.
b. Justify the solution proposed above by explaining a potential advantage of using a different renewable resource to generate electricity.
Answer:
a) wind power system, turbines powered, solar power system
b) the possibility of creating jobs for the local workforce and of maintaining the environment without damaging it.
Explanation:
In a grassland system it may not have great changes in height or mountain system where it is easy to represent a river, therefore a hydroelectric power system is not very feasible.
a) You can have several alternative energy systems.
* If there is a fairly constant air current, a wind power system could be implemented.
* If there is a river with an acceptable flow, a generation system can be implemented with turbines powered by the river flow.
* Another system is a solar power system
b) To select any of the possible systems proposed, the current and future energy requirements of the region must be analyzed.
The amount of energy that each proposal can supply
Analyze the installation costs and the economic benefits of a given system.
Study the possible problems for the maintenance of each system.
A great advantage of these systems is the possibility of creating jobs for the local workforce and of maintaining the environment without damaging it.
The most plausible renewable energy source in a grassland is wind energy.
Renewable energy refers to energy that is obtained from wind, water biomass or underground heat. All of these sources of energy are inexhaustible and hold great prospect to solving the current energy deficit is many parts of the world.
In grasslands, the most plausible renewable source of energy is wind. Winds are abundant in grasslands . It is more plausible than hydroelectric power because it does not create any adverse environmental impact. It is the cleanest energy source.
Learn more about renewable energy: https://brainly.com/question/4038933
On Earth, what can a divergent boundary
cause?
A. An iceberg
B. A plateau
C. A rift valley
Answer: C
Explanation:
Divergent plate boundary is a linear feature that exists between two tectonic plates that are moving away from each other. Divergent boundaries within continents initially produce rifts, which eventually become rift valleys. Most active divergent plate boundaries occur between oceanic plates and exist as mid-oceanic ridges.
did anyone do the, kinetic energy lab report in physics?? plzzz help a girl outttttttt i need answerss????ill give you as much brainlist or points
Answer:
yes
Explanation:
BRAINLEST FOR CORRECT ANSWER
Which has more momentum: a 3 kg sledgehammer swung at 1.5 m/s OR a 4 kg sledgehammer swung at 0.9 m/s? SHOW YOUR WORK FOR BRAINLEST
Answer:
3kg sledgehammer swung at 1.5 m/s
Explanation:
Small Sledgehammer:
Mass:3.0
Velocity:1.5
MASS×VELOCITY=MOMENTUM
3.0×1.5= 4.5 (momentum)
Large Sledgehammer:
Mass:4.0
Velocity:0.9
4.0×0.9=3.6 (momentum)
higher momentum is the smaller Sledgehammer.
A pendulum is swimging. It swings 85 complete swings and this takes 102 seconds. What is the frequency?
Answer:
0.833 Hz
Explanation:
While, there are plenty of ways to calculate frequency, the one formula you should use in this case is:
#times/seconds --> 85/102
= 0.833 Hz
1. A Zambeef delivery track travels 18 km north, 10 km east, and 16 km south. What is its final displacement from the origin?
Answer:
10.2 km
Explanation:
Displacement is the shortest distance from your original position after movement.
Now, the Zambeef delivery truck moves 18 km north and then 10 km east and then 16 km south.
This means that vertically the truck is 2km short of the 18 km he travelled north..
So we can find the displacement using pythagoras theorem..
Let d be the distance from the current position to the initial position.
Thus;
d² = 2² + 10²
d² = 4 + 100
d = √104
d ≈ 10.2 km
I have attached a diagram showing the direction of this displacement
pressure, V is volume , T is temperature of a gas and R is gas constant.
b) Can the sum of two equal vectors be equal to either of the vectors?
Explain