Answer:
2.528x10⁻³M
Explanation:
Molarity is an unit of concentration used in chemistry. Is defined as the moles of solute per liter of solution.
To find the molarity of the solution we need to determine the moles of ammonium sulfate present in the initial 49.16mL solution and, with total volume, we can find the molarity, thus:
Moles ammonium sulfate:
49.16mL = 0.04916L * (0.0270 moles / L) =
1.327x10⁻³moles ammonium sulfate
These moles are present in 525.0mL = 0.525L. Thus, molarity of the solution will be:
1.327x10⁻³moles ammonium sulfate / 0.525L =
2.528x10⁻³MA liquid has a volume of 62.7 mL and a density of 2.59 g/mL. What is its mass? (show all work)
Answer:
162.4
Explanation:
The formula for mass is density* volume so 62.7 multiplied by 2.59 equals 162.393. then you round so your anwser would be 162.4
which dissolved first in acetone? food coloring or liquid paint?
Answer:
Liquid paint.
Explanation:
Liquid paints are dissolved first in acetone. Most of the food dyes are not soluble in acetone.
What is acetone?Acetone is an organic compound comes under the category of ketones. It contains a carbonyl group and can dissolve most of the organic solvents.
The active ends in acetone easily forms hydrogen bonds with other solvents with polar or nonpolar groups.
Xylene, benzene, toluene, aromatic azo dyes etc. are common components in paint. Which are easily miscible with acetone.
Hence, liquid paints dissolve in acetone and food dyes are hard o dissolve in it.
To learn more about acetone, refer the link below:
https://brainly.com/question/13334667
#SPJ2
Violet light has a wavelength of 4.50 x 10-12 m. What is the frequency?*
3 points
1.5 x10^20 1/s
0.0135 1/s
6.77x10^19 1/5
3x10^8 1/s
Green light has a frequency of 6.73 x 1014 1/s. What is the wavelength?*
3 points
2.24x10^6 m
4.46x10^-7 m
2.02 x 10^23 m.
4.95 x 10^-24 m
3 points
What is the energy (Joules) of violet light with a frequency = 3.43 x 10^14
1/s? *
4.54x10^-19 J
1.99x10^-25 J
1.93 x 10^-48 J
2.27 x 10^-19 J
Answer:
Frequency = 6.67x10¹⁹ s⁻¹
Wavelength = 4.46x10⁻⁷m
e = 2.27x10⁻¹⁹J
Explanation:
To convert frequency to wavelength and vice versa we use the equation:
Wavelength = Speed of light / Frequency
Speed ligth is 3x10⁸m/s
For a wavelength of 4.50x10⁻¹²m:
4.50x10⁻¹²m = 3x10⁸m/s / Frequency
Frequency = 3x10⁸m/s / 4.5x10⁻¹²m
Frequency = 6.67x10¹⁹ s⁻¹For a frequency of 6.73x10¹⁴s⁻¹:
Wavelength = 3x10⁸m/s / 6.73x10¹⁴s⁻¹
Wavelength = 4.46x10⁻⁷mAnd energy, e, from frequency, is obtained as follows:
e = h ₓ frequency
Where h is Planck's constant, 6.626x10⁻³⁴J*s
e = 6.626x10⁻³⁴J*s*3.43x10¹⁴s⁻¹
e = 2.27x10⁻¹⁹JWhich of the following contribute(s) to most of the mass of an atom? Question 5 options: A) Neutrons only B) Protons and electrons C) Protons and neutrons D) Protons only
Answer:
C
Explanation:
Hope this helps :)
Define a function compute_gas_volume that returns the volume of a gas given parameters pressure, temperature, and moles. Use the gas equation PV
Answer:
def compute_volume(pressure,moles,temperature):
volume = (8.314 * moles * temperature)/pressure
print("Volume: "+str(volume))
Explanation:
This line defines the function
def compute_volume(pressure,moles,temperature):
This line calculates the volume
volume = (8.314 * moles * temperature)/pressure
This line prints the calculated volume
print("Volume: "+str(volume))
What is the atomic number of arsenic (As)?
O A. 33
O B. 15
C. 75
D. 4
SUB
Answer:
33
Explanation:
The atoms of which element will gain electrons to form an ion?
oxygen
calcium
lithium
mercury
Explanation:
Oxygen will gain electrons to form ion (O²⁻).
Calcium loses electron to form ion (Ca²⁺)
Lithium loses electron to form ion (Li⁺)
Mercury loses electron to form ion (Hg²⁺)
Here it is stated in question that the element will gain electron it means electron bears negative charge.
Therefore,
Option A is correct ✔.
the coefficient of 02 is needed to balance the equation C3h8+O2+3co2+4H20
Answer:The anwser is 5
Explanation:
Which of the following represents a species with 16 protons and 18 electrons? A) Ar B) S C) S²⁻ D) Si⁴⁻ E) S²⁺ Question 5 of 40
Answer:S²⁻
Explanation:
Sulphur is in group 16. The atomic number of sulphur is 16.
However, sulphur can accept two electrons to form the sulphide ion S²⁻ which contains 18 electrons, hence the answer provided above.
Which is denser a liquid or solid why?
Answer:
Liquids are usually less dense than solids but more dense than air. Temperature can change a liquid's density. For example, increasing the temperature of water causes the molecules to spread farther apart. The farther apart the molecules are, the less dense the water is.
Answer:
Solids are usually much more dense than liquids and gases, but not always.
Explanation:
Mercury, a metallic element that is a liquid at room temperature, is denser than many solids. Aerogel, a very unusual human-made solid, is about 500 times less dense than wate
How many moles would be in 24.23 grams of SrSO4?
Use two digits past the decimal for all values.
Answer:
about 0.13 mol
Explanation:
To find number of mols when given grams you first have to find the molar mass of the compound. This is done by adding up the atomic masses of the element in the compound. So Sr= 88 g/mol S=32 g/mol and O=16 g/mol. Then 88+32+(16x4)=184. Then using this you can convert from grams to mols by dividing the grams by the molar mass. So, 24.23/184 equals about 0.13 mol.
2NH.
N2 + 3H2
Reactants
Product
On the balanced equation above, how many
atoms of each element are in the reactant?
N =
H =
Answer:
N=2
H=6
Explanation:
1.Balance a chemical equation in terms of moles.
2.Use the balanced equation to construct conversion factors in terms of moles.
3.Calculate moles of one substance from moles of another substance using a balanced chemical equation.
The law of conservation of matter says that matter cannot be created or destroyed. In chemical equations, the number of atoms of each element in the reactants must be the same as the number of atoms of each element in the products.
(P.s it could also be where you have to solve it in which you have to simplify it first then solve it.) like adding them all up.
Hope this is the answer. :)
All good experiments should be...
What was one main point of Dalton’s atomic theory?
A. That atoms were made up of positive and negative charges
B. That atoms changed as they formed compounds
C. That atoms has a nucleus at the center
D. That atoms made up the smallest form of matter
The main point of Dalton’s atomic theory is that the atoms are made up the smallest form of matter. Hence Option (D) is Correct
What is Dalton's Atomic Theory ?
The 5 main points of Dalton's Atomic theory was ;
Elements are composed of extremely small particles called atoms that are indivisible and indestructibleAll atoms of a given element are identical; they have the same size, mass, and chemical propertiesAtoms of 1 element are different from the atoms of all other elementsCompounds are composed of atoms of more than 1 element. The relative number of atoms of each element in a given compound is always the same.Chemical reactions only involve the rearrangement of atoms. Atoms are not created or destroyed during chemical reactions.Therefore, The main point of Dalton’s atomic theory is that the atoms are made up the smallest form of matter. Hence Option (D) is Correct
Learn more about Atom here ;
https://brainly.com/question/657632
#SPJ2
Answer:
D is correct
Explanation:
which of the two pure substance consists of different types of Element
Answer:Two Main Types of Pure Substances
Elements and compounds are the two types of pure substances. Examples of common elements include carbon, nitrogen and hydrogen. They consist of one type of atom and cannot break down into something else. Every pure carbon substance, for example, has the same particles in it.
Explanation:I think
The discharge of chromate ions (CrO42-) to sewers or natural waters is of concern because of both its ecological impacts and its effects on human health if the receiving water is later used as a drinking water source. One way in which chromate can be removed from solution is by its reaction with ferrous ions (Fe2+) to form a mixture of chromic hydroxide and ferric hydroxide solids [Cr(OH)3(s) and Fe(OH)3(s), respectively], which can then be filtered out of the water. The overall reaction can be represented as
CrO42- + 3 Fe2+ + 8 H2O --> Cr(OH)3(s) + 3 Fe(OH)3(s) + 4 H+
How much particulate matter would be generated daily by this process at a facility that treats 60 m3/h of a waste stream containing 4.0 mg/L Cr, if the treatment reduces the Cr concentration enough to meet a discharge limit of 0.1 mg/L?
Answer:
45727g
Explanation:
So, have the overall ionic equation given as the following;
CrO42^- + 3 Fe2^+ + 8 H2O ------> Cr(OH)^3(s) + 3 Fe(OH)^3(s) + 4 H^+.
So, we have (from the question) that the amount or quantity of the waste stream daily = 60m^3/h, and the waste stream daily contains waste stream containing = 4.0 mg/L Cr, and the discharge limit = 0.1 mg/L.
Step one: convert m^3/ h to L/h. Therefore, 60 m^3/h × 1000dm^3 = 60000 L/h .
Step two: Determine or calculate the the value of Cr used up.
The value of Car used up ={ 60,000 × ( 4.0 - 0.1) } ÷ 1000 = 234 g.
Step three: Determine or calculate the mass of Cr(OH)3 and the mass of Fe(OH)3.
The number of moles of Cr = 234/52 = 4.5 moles.
Molar mass of Cr(OH)3 = 103 g/mol and the molar mass of Fe(OH)3 = 106.8 g/mol.
Thus, the mass of Cr(OH)3 = 4.5 × 103 = 463.5 g.
And the mass of Fe(OH)3 = 13.5 × 106.8 = 1441.8 g.
Hence, the total = 463.5 g + 1441.8 g = 1905.3 g.
Step four: Determine or calculate the How much particulate matter would be generated daily.
The amount of the particulate that would be generated daily = 24 × 1905.3 = 45727g.
is a renewable resource used for the generation of electricity.
A. Natural gas
B. Coal
C. Petroleum
O D. Biomass
Answer:
its natural gas because i had something like this
Explanation:
The renewable energy sources, such as biomass, geothermal resources, water, wind, etc. are called the natural resources. These can be converted into clean and usable energy. The correct option is D.
What is Renewable energy?The energy which is derived from the natural sources which are replenished at a higher rate than they are consumed is defined as the Renewable energy. The renewable energy generating produce lower emissions than burning the fossil fuels.
The word biomass refers to the organic plant matter which is converted into fuel and used as an energy source. The biomass fuel is considered as an important renewable and sustainable source of energy. It is used for the production of electricity.
The organic materials like wood, agricultural wastes, etc. acts as the excellent sources to produce biomass fuel. It is possible to burn the biomass fuel directly and later converted into methane and ethanol biofuels.
Thus the correct option is D.
To know more about renewable energy, visit;
https://brainly.com/question/13258101
#SPJ7
Which statement best demonstrates how data from a global positioning system (GPS) can be used to lessen the effects of a
wildfire? (1 point)
GPS data can be used by people to quickly evacuate an area because of a wildfire
GPS data can be used by scientists to predict weather patterns that can lead to a wildfire
GPS data can be used by firefighters to identify the boundaries of a wildfire
GPS data can be used by first responders to calculate the safest route to a wildfire
Answer: here is your answer
Explanation: You are visiting your Grandmother and notice that she is eating a balanced diet, taking vitamins, getting the proper amount of sleep and is not overweight. Despite her healthy lifestyle, she appears run down and tired. You realize that it's due to her lack of physical activity. Write a convincing letter to your grandma explaining the benefits of participating in regular physical activity.
Which element is classified as a noble gas?
Answer:
any of the seven chemical elements that make up Group 18 (VIIIa) of the periodic table. The elements are helium (He), neon (Ne), argon (Ar), krypton (Kr), xenon (Xe), radon (Rn), and oganesson (Og). :)
Explanation:
Answer:
For edge, the answer is;
D. Xe
(Xenon)
Explanation:
edg- answers ;p
If equal volumes of a strong base and a weaker acid are mixed together, what would you expect the pH of the resulting salt to be
Answer:
Above 7
Explanation:
The equivalence point of any titration can be read off from the appropriate titration curve.
A titration curve is a plot of the pH of analyte against the volume of titrant added.
For a strong base and weak acid, the equivalence point lies above 7.
The pH of the resulting salt to be pH> 7 .
What does Equivalence point tell?The equivalence point of any titration can be read off from the appropriate titration curve. A titration curve is a plot of the pH of analyte against the volume of titrant added. It is a point in titration at which the amount of titrant added is just enough to completely neutralize the analyte solution. At the equivalence point in an acid-base titration.
For a strong base and weak acid, the equivalence point lies above 7.
Find more information about Equivalence point here:
brainly.com/question/18933025
20
How do you determine the number of barium atoms in the formula below?
4Ba(OH)2
F
# of Ba atoms = coefficient 4 + subscript 1 = 5
G
# of Ba atoms = coefficient 4 X subscript 1 = 4
H
# of Ba atoms = subscript 4 X coefficient 2 = 6
# of Ba atoms coefficient 1 + subscript 1 = 2
J
Answer:
G is correct option:
# of Ba atoms = coefficient 4 × subscript 1= 4
Explanation:
Formula:
4Ba(OH)₂
G is correct option:
# of Ba atoms = coefficient 4 × subscript 1= 4
Because there are only 4 atoms of Ba in given formula.
Ba(OH)₂ contain one atom of Ba while in question there are 4 moles of Ba(OH)₂ present thus total 4×1 = 4 atoms of Ba present.
Other options are incorrect. Because,
F:
# of Ba atoms = coefficient 4 + subscript 1 = 5
This shows given formula contain 5 Ba atoms. So it is incorrect.
H:
# of Ba atoms = subscript 4 × coefficient 2 = 6
This shows that subscript is 4 which is incorrect because coefficient is 4 and subscript is 1.
j:
# of Ba atoms = subscript 1 + coefficient 1 = 2
This option shows that subscript is one which is correct but coefficient is incorrect. The coefficient of Ba is 4 and coefficient is always multiply with subscript not added. So this option is also incorrect.
10. The density of aluminum is 2.70 g/mL. If the mass of a piece of aluminum is 244 grams, what is the volume of the aluminum?
Answer:
The answer is 90.37 mLExplanation:
The volume of a substance when given the density and mass can be found by using the formula
[tex]volume = \frac{mass}{density} \\ [/tex]
From the question we have
[tex]volume = \frac{244}{2.7} \\ = 90.370370...[/tex]
We have the final answer as
90.37 mLHope this helps you
What is the heat gjoules transferred by a chemical reaction to the reservoir of a calorimeter containing 135g of dilute aqueous solution (c=4.184 J/g^ C) the reaction causes the temperature of the reservoir to rise from 23.0 27.0 degrees * C
Answer:
Required heat = 2,259.36 N (approx)
Explanation:
Given:
Mass = 135 g
Specific heat (c) =4.184 J/gC
Change in temperature ΔT = 27-23 = 4 c
Find:
Required heat
Computation:
Q = mcΔT
Q = (135)(4.184)(4)
Required heat = 2,259.36 N (approx)
The heat transferred by the chemical reaction to the reservoir of a calorimeter containing 135 g of dilute aqueous solution is 2259.36 J
To solve this question, we'll begin by calculating the change in the temperature of the reservoir. This can be obtained as follow:
Initial temperature (T₁) = 23 °C
Final temperature (T₂) = 27 °C
Change in temperature (ΔT) =?ΔT = T₂ – T₁
ΔT = 27 – 23
ΔT = 4 °CFinally, we shall determine the heat transferred to the reservoir.
Change in temperature (ΔT) = 4 °C
Mass (M) = 135 g
Specific heat capacity (C) = 4.184 J/gºC
Heat (Q) =?Q = MCΔT
Q = 135 × 4.184 × 4
Q = 2259.36 JTherefore, the heat transferred by the chemical reaction to the reservoir of a calorimeter containing 135 g of dilute aqueous solution is 2259.36 J
Learn more: https://brainly.com/question/10286596
Please help me!!!:)))
Answer:
blocks 1 and 2 the rhdh huff hgfhh5
Forty milliliter of a liquid has a mass of 80 grams. What is the density of this substance?
Answer:
2.00g/ml
Explanation:
If water has a density of 1.00g/ml, and theres
40ml of it, it would weigh 40g
The substance is twice as dense as water, making its density 2.00g/ml
PLEASE PLEAS HELP Which of the following compounds is insoluble in water?
a) ZnSO4
b) K2SO4
c) Na2CO3
d) Ag2CO3
Answer:
Your answer is d
Explanation: silver carbonate Ag2CO3 is insoluble in water
Which element contains one set of paired and three unpaired electrons in its fourth and outer main energy level?
Explanation:
Phosphorus (P) because of the 5 valence electrons total, 3 of them are in the 3p sublevel, and according to Hund's rule, they "single-fill" each orbital first.
Which of the following evidence supports the theory of plate tectonics
Answer:
seafloor spreading
Explanation:
i took the test
A scientist plans to find out the cause of decrease in bird population in a location. He interviews 50 people who work in the local oil mine and 45 of them believe that the mine does not affect the birds. The scientist concludes that 90 percent of people in the location believe that the local oil mine does not cause decrease in bird population. Why is the scientist's conclusion most likely unreliable? (2 points)
Group of answer choices
a. the results of the investigation cannot be repeated
b. the source of information could be biased
c. bird population cannot be measured accurately
d. the investigation is done by only one person
Answer:
Explanation:
noble gas notation for titanium
Answer:
Titanium [Ar] 3d2 4s2
Explanation: