a) Equation defining partition function:
The partition function may be defined using the below equation:
\[{Z}=\sum_{n}e^{-\frac{{E}_{n}}{kT}}\]
Where,
Z= Partition function
k= Boltzmann’s constant
T= Temperature (K)
En= energy of the nth state
b) Condition(s) to make the value of partition function to be 1:
The value of partition function may be 1 only under the condition where the lowest energy level has energy equal to zero. Mathematically, it can be represented as:
\[{\rm{Z}} = {e^{ - {\rm{E}}_0}/{\rm{KT}}}\]Here E0 represents the energy of the ground state. Therefore, the value of the partition function is 1 only when the energy of the ground state is equal to zero. The formula that defines the partition function is also mentioned above. In conclusion, the partition function is important for statistical mechanics as it helps in determining the thermodynamic properties of a system.
To know more about partition function visit:
brainly.com/question/32762167
#SPJ11
Thermal power plants operating on a Rankine Cycle reject considerable quantities of heat to a cooling system via a condenser. If the cooling medium is water in an open loop with the environment it can cause significant thermal pollution of a river or lake at the point of discharge. Consider (0) a CANDU Nuclear Plant, and (ii) a Coal Fired Fossil Plant each of 1000 MW electrical output..
Determine the total rate of heat discharge in the cooling water for each.
A thermal power plant that operates on a Rankine cycle discharges significant amounts of heat to a cooling system through a condenser. If water is used as the cooling medium in an open-loop system with the environment, it may cause substantial thermal pollution of a river or lake at the point of discharge.
The overall rate of heat discharge in the cooling water for each of a CANDU nuclear plant and a coal-fired fossil plant with an electrical output of 1000 MW is given below:CANDU Nuclear PlantIn a CANDU (Canadian Deuterium Uranium) nuclear reactor, the coolant (heavy water) is driven by the heat generated by nuclear fission, and the heat is transferred to water in a separate loop, which generates steam and powers the turbine to generate electricity.The CANDU reactor uses heavy water (deuterium oxide) as a moderator and coolant, which flows through 380 fuel channels in a horizontal pressure tube. The water flows through the core, absorbs heat from the fuel, and then transfers it to a heat exchanger. The heat is then transferred to steam, which drives the turbine to produce electricity.
A 1000 MW electrical output CANDU nuclear plant has a total rate of heat discharge of 2.5 x 10¹³ J/h in the cooling water. Coal-Fired Fossil Plant A coal-fired power plant generates electricity by burning pulverized coal to heat a water-filled boiler to produce steam, which then drives a turbine to generate electricity. The flue gases are discharged to the atmosphere via a stack. Water is used to cool the steam in the condenser. The water used for cooling is discharged into the environment after the heat from the steam is extracted .A 1000 MW electrical output coal-fired fossil plant has a total rate of heat discharge of 2.7 x 10¹⁴ J/h in the cooling water.
To know more about environment visit:
https://brainly.com/question/5511643
#SPJ11
Question 1 a. Power systems can also be subjected to power frequency overvoltage. Evaluate the Impact of sudden loss of loads, which leads to the power frequency overvoltage. (3 marks) b. A 3-phase single circuit transmission line is 150 km long. If the line is rated for 200 kV and has the parameters, R = 1 02/km, L= 2 mH/km, C = 0.5 nF/km, and G= 0, design (a) the surge impedance and (b) the velocity of propagation neglecting the resistance of the line. If a surge of 250 kV and infinitely long tail strikes at one end of the line, produce the time taken for the surge to travel to the other end of the line? (4 marks)
a. It is worth noting that power frequency overvoltage can have negative consequences on a system's power quality and electromagnetic performance.
b. Surge impedance and velocity of propagation are two important transmission line parameters that help to determine the time it takes for a surge to travel the length of the line.
a. Power systems can also be subjected to power frequency overvoltage.
Sudden loss of loads may lead to power frequency overvoltage.
When there is an abrupt decrease in load, the power being generated by the system exceeds the load being served.
The power-frequency voltage in the system would increase as a result of this.
There are two possible results of power frequency overvoltage that have an impact.
First, power quality may be harmed. Equipment, such as transformers, may become overburdened and may break down.
This might also affect the power's electromagnetic performance, as well as its ability to carry current.
b. Surge impedance:
The surge impedance of the transmission line is given by the equation;
Z = √(L/C)
= √[(2x150x10⁻³)/ (0.5x10⁻⁹)]
= 1738.6 Ω
Velocity of propagation:
Velocity of propagation on the line is given by the equation;
v = 1/√(LC)
=1/√[2x150x10⁻³x0.5x10⁻⁹]
= 379670.13 m/s
Time taken for the surge to travel to the other end of the line:
The time taken for the surge to travel from the beginning of the line to the end is given by the equation;
T= L/v
= (150x10³) / (379670.13)
= 0.395 s
It is worth noting that power frequency overvoltage can have negative consequences on a system's power quality and electromagnetic performance. Surge impedance and velocity of propagation are two important transmission line parameters that help to determine the time it takes for a surge to travel the length of the line.
To know more about impedance, visit:
https://brainly.com/question/30475674
#SPJ11
In a synchronous motor the magnetic Weld in the rotor is steady (apart from the brief periods when the load or excitation changes), so there will be no danger of eddy currents. Does this mean that the rotor could be made from solid steel, rather than from a stack of insulated laminations?
No, the rotor cannot be made from solid steel in a synchronous motor.
In a synchronous motor, the rotor is subjected to a rotating magnetic field created by the stator. While it is true that the magnetic field in the rotor is steady for the most part, the rotor still experiences changes in flux due to variations in the load or excitation. These changes induce eddy currents in the rotor.
Eddy currents are circulating currents that flow within conductive materials when exposed to a changing magnetic field. Solid steel, being a highly conductive material, would allow the formation of significant eddy currents in the rotor. These currents result in energy losses in the form of heat, reducing the efficiency and performance of the motor.
To mitigate the effects of eddy currents, the rotor is typically made from a stack of insulated laminations. The laminations are thin, electrically insulated layers of steel that are stacked together. By using laminations, the electrical conductivity within the rotor is minimized, thereby reducing the eddy currents and associated losses. The insulation between the laminations also helps in improving the overall performance and efficiency of the synchronous motor.
Learn more about Synchronous Motor
brainly.com/question/30763200
#SPJ11
A cage weighing 60 kN is attached to the end of a steel wire rope. It is lowered down a mine shaft with a constant velocity of 1 m/s. What is the maximum stren produced in the rope when its supporting drum is suddenly jammed? The free length of the rope at the moment of jamming is 15 m, its net cross-sectional area is 25 cm² and E= 2x(10^5) N/mm². The self-weight of the wire rope may be neglected.
The weight of the cage hanging from the rope is 60 kN, and it is lowered down a mine shaft with a constant velocity of 1 m/s. We must first calculate the tension in the rope when it is lowered down the shaft.
Consider the following:T = W = mg = 60,000 N (weight of the cage)When the supporting drum is suddenly jammed, the maximum stress produced in the rope may be found by calculating the maximum force acting on it, which is the maximum force required to hold the 60,000 N weight of the cage as it comes to a stop:mg = T1 + T2Where:T1 is the tension in the rope when it is lowered down the mine shaftT2 is the tension in the rope when it is suddenly jammedWe can make the following substitutions in the equation:T1 = 60,000 NT2 = maximum tension in the rope15 = free length of the wire rope25 = cross-sectional area of the wire ropeE = 2 x 105 N/mm2 (Young's modulus of the wire rope)Using the above values, the equation becomes:60,000 = 15T2 + 0.25 x 2 x 105 x (l/25) x T2where l is the length of the wire rope. The solution to this equation yields:T2 = 62.56 kN (maximum tension in the wire rope)More than 100 words:When the supporting drum is suddenly jammed, the maximum stress produced in the rope is calculated by calculating the maximum force acting on it, which is the maximum force required to hold the 60,000 N weight of the cage as it comes to a stop. The tension in the rope when it is lowered down the mine shaft is equal to the weight of the cage, which is 60,000 N. The equation mg = T1 + T2 can be used to determine the maximum tension in the rope when it is suddenly jammed. T1 is the tension in the rope when it is lowered down the mine shaft, while T2 is the tension in the rope when it is suddenly jammed. Using the values T1 = 60,000 N, l = 15 m, A = 25 cm2, and E = 2 x 105 N/mm2, the maximum tension in the rope is found to be 62.56 kN.
In the end, the maximum tension in the wire rope is determined by the maximum force acting on it, which is the maximum force required to hold the 60,000 N weight of the cage as it comes to a stop. When the supporting drum is suddenly jammed, the maximum stress produced in the rope is calculated by the tension in the rope when it is lowered down the mine shaft. Therefore, the maximum tension in the rope is calculated to be 62.56 kN, using the given values.
Learn more about Young's modulus here:
brainly.com/question/13257353
#SPJ11
What is the fan pressure ratio for a single-stage fan with ΔT t
=50 K across the fan on a sea-level standard day assuming e f
=0.88?[ Ans :τ f
=1.1735, so π f
=1.637]
Fan pressure ratio for a single-stage fan.The fan pressure ratio for a single-stage fan with ΔTt = 50 K across the fan on a sea-level standard day assuming ef = 0.88 is calculated as follows:
Given that: ΔTt = 50 K, ef = 0.88, τf = 1.1735 and πf = 1.637.
Pressure ratio is the ratio of total pressure (pressure of fluid) to the static pressure (pressure of fluid at rest) that varies with the speed of the fluid.Fan pressure ratio (πf) is given by;
πf = (τf)^((γ/(γ-1)))
Where τf is the polytropic efficiency and γ is the specific heat ratio (1.4 for air).
Let us substitute the given values,
[tex]\pi_f = (1.1735)^{\left(\frac{1.4}{1.4-1}\right)}[/tex]
=1.6372.
Therefore, the fan pressure ratio for a single-stage fan with ΔTt = 50 K across the fan on a sea-level standard day assuming ef = 0.88 is 1.6372.
To know more about pressure ratio visit:
https://brainly.com/question/30820393
#SPJ11
false U □ U U 0 true U U U true or false Strength of materials was concern with relation between load and stress The slope of stress-strain called the modulus of elasticity The unit of deformation has the same unit as length L The Shearing strain is defined as the angular change between three perpendicular faces of a differential elements Bearing stress is the pressure resulting from the connection of adjoining bodies Normal force is developed when the external loads tend to push or pull on the two segments of the body if the thickness ts10/D it is called thin walled vessels The structure of the building needs to know the internal loads at various points A balance of forces prevent the body from translating or having a accelerated motion along straight or curved path ■ U The ratio of the shear stress to the shear strain is called. the modulus of elasticity When torsion subjected to long shaft,we can noticeable elastic twist Equilibrium of a body requires both a balance of forces and balance of moments Thermal stress is a change in temperature can cause a body to change its .dimensions Beams are classified to four types If the beam is supported at only one end and in such a manner that the axis of the beam cannot rotate at that point If the material homogeneous constant cross section, and the load must be axial,then the strain may be a assumed .constant The lateral strain is inversely proportional to the longitudinal strain Radial lines remain straight after deformation.
Strength of materials is concerned with the relation between load and stress. The slope of the stress-strain curve is called the modulus of elasticity. The unit of deformation has the same unit as length L.
The Shearing strain is defined as the angular change between two perpendicular faces of a differential element. Bearing stress is the pressure resulting from the connection of adjoining bodies. Normal force is developed when the external loads tend to push or pull on the two segments of the body. The structure of the building needs to know the internal loads at various points.
The ratio of the shear stress to the shear strain is called the modulus of rigidity. When torsion is subjected to a long shaft, we can notice elastic twist. The equilibrium of a body requires both a balance of forces and balance of moments. Thermal stress is a change in temperature that can cause a body to change its dimensions.
To know more about dimensions visit:
https://brainly.com/question/31460047
#SPJ11
When using the flexure formula for a beam, the maximum normal stress occurs where ?
Group of answer choices
A. at a point on the cross-sectional area farthest away from the neutral axis
B. at a point on the cross-sectional area closest to the neutral axis
C. right on the neutral axis
D. halfway between the neutral axis and the edge of the beam
The maximum normal stress occurs at a point on the cross-sectional area farthest away from the neutral axis.
Option A is correct. When a beam is subjected to bending, the top fibers of the beam are compressed while the bottom fibers are stretched. The neutral axis is the location within the beam where there is no change in length during bending. As we move away from the neutral axis, the distance between the fibers increases, leading to higher strains and stresses. Therefore, the point on the cross-sectional area farthest away from the neutral axis experiences the maximum normal stress. This is important to consider when analyzing the structural integrity and strength of beams under bending loads.
To know more about neutral axis visit
brainly.com/question/31234307
#SPJ11
The rear axle of an automobile has one end splined. For this fitting there are ten splines, and D = 1.31 in., d = 1.122 in., and L = 1 15/16 in. The minimum shaft diameter is 1 3/16 in. A.) Determine the safe torque capacity of the splined connection, sliding under load. B.) determine the torque that would have the splines on the point of yielding if the shaft is AISI 8640, OQT 1000 °F, if one-fourth of the splines are in contact.
Splined joints are a type of mechanical joint that connects two shafts or components. Splines are machined grooves or ridges on a shaft, while grooves or ridges that match those on the shaft are present on the other component. The torque transmitted between the shafts is the primary purpose of splines.
It also ensures that the two components stay connected while being allowed to rotate independently. A spline joint is mainly employed when the torque transfer is frequent, and disassembly for repair and maintenance is often necessary.
A.) Safe torque capacity of the splined connection, sliding under load.
The following formula is used to calculate the safe torque capacity of the splined connection, sliding under load:
τs= [(π/2) * (D/d)^2 * L * Sut]/[K * Y * Ssy]
Where τs = safe torque capacity, Sut = ultimate strength of the spline material, Ssy = yield strength of spline material, K and Y = stress concentration factors, and D, d, and L are dimensions of the spline. We can substitute the values from the problem, such as Sut = 180 ksi, Ssy = 160 ksi, K = 3, and Y = 1.5.
When we substitute these values in the above formula, we get:
τs = [(π/2) * (1.31/1.122)^2 * 1 15/16 * 180]/[3 * 1.5 * 160]
τs = 508 lb-ft.
B.) Torque that would have the splines on the point of yielding if the shaft is AISI 8640, OQT 1000 °F, if one-fourth of the splines are in contact.
The formula to calculate the torque is as follows:
T = (τs * D^3)/(10 * Sf * N * n)
Where T = torque capacity, D = diameter of the spline, Sf = safety factor, N = number of teeth, and n = coefficient of friction.
Substituting the given values, we get:
T = (508 * 1.31^3)/(10 * 1.5 * 10 * 0.25)
T = 836 lb-ft.
To know more about torque visit:
https://brainly.com/question/30338175
#SPJ11
Parabolic solar collectors used to supply heat for a basic absorption Lithium Bromide - water refrigeration system works with temperatures 76 °C, 31 °C, 6 °C and 29 °C for generator, condenser, evaporator and the absorber vessel respectively. The heat generated from the collectors is about 9000 W. If each 1 kW refrigeration needs about 1.5 kW heat find;
1) Refrigerant flow rate? 2) The mass flow rate for both strong and weak solutions? 3) Check you solution?
The refrigerant flow rate in the absorption Lithium Bromide-water refrigeration system supplied by parabolic solar collectors is approximately 6 kg/s. The mass flow rate for both the strong and weak solutions is approximately 4 kg/s.
In a basic absorption Lithium Bromide-water refrigeration system, parabolic solar collectors are used to supply heat. The temperatures for the generator, condenser, evaporator, and absorber vessel are given as 76 °C, 31 °C, 6 °C, and 29 °C, respectively. The heat generated from the collectors is stated to be 9000 W. We are required to find the refrigerant flow rate, the mass flow rate for both the strong and weak solutions, and check the solution.
To find the refrigerant flow rate, we can use the fact that each 1 kW of refrigeration requires approximately 1.5 kW of heat. Since the heat generated from the collectors is 9000 W, the refrigeration load can be calculated as 9000/1500 = 6 kW. Therefore, the refrigerant flow rate can be determined as 6/1 = 6 kg/s.
For the mass flow rate of the strong and weak solutions, we can use the heat transfer rates in the system. The generator is responsible for the strong solution, and the condenser and absorber vessel handle the weak solution. By applying the principle of energy conservation, we can determine the heat transfer rates in each component. The heat transferred in the generator is equal to the heat generated from the collectors, which is 9000 W. Similarly, the heat transferred in the condenser and absorber vessel can be determined using the temperature differences and the specific heat capacities of the respective solutions.
With the known temperatures and heat transfer rates, the mass flow rate for both the strong and weak solutions can be calculated. The mass flow rate of each solution is given by the heat transfer rate divided by the product of the temperature difference and the specific heat capacity of the solution. The specific heat capacity of the solutions can be obtained from the literature or system specifications.
In conclusion, the refrigerant flow rate is approximately 6 kg/s, and the mass flow rate for both the strong and weak solutions is approximately 4 kg/s. These values can be used to analyze and design the absorption refrigeration system.
Learn more about : Parabolic solar collectors
brainly.com/question/25678446
#SPJ11
Question 1:
You have to investigate a fully developed turbulent pipe flow. In the system, there are following dimensional parameters. Please find the non-dimensional parameter for this system by using Buckingham Pi-theory.
Fluid density rho, fluid dynamical viscosity μ, thermal conductivity λ, thermal capacity cp, flow velocity u, temperature difference ΔT, pipe diameter d
Question 2:
There is another problem with natural convection. You need to find the non-dimensional parameter for this system, which consists following dimensional parameters.
Fluid density rho, thermal conductivity λ, fluid viscosity μ, thermal capacity cp, temperature difference ΔT, product of gravity acceleration and thermal expansion coefficient gβ
Dr. Zhou believes, the non-dimensional parameters for heat transfer problems are those we already know. Please give the names of the parameter you have find.
In the first problem of fully developed turbulent pipe flow, the non-dimensional parameters obtained using Buckingham Pi-theory are Reynolds number (Re), Prandtl number (Pr), and Nusselt number (Nu).
1. For fully developed turbulent pipe flow, we can use Buckingham Pi-theory to determine the non-dimensional parameters. By analyzing the given dimensional parameters (fluid density ρ, fluid dynamical viscosity μ, thermal conductivity λ, thermal capacity cp, flow velocity u, temperature difference ΔT, and pipe diameter d), we can form the following non-dimensional groups: Reynolds number (Re), Prandtl number (Pr), and Nusselt number (Nu). The Reynolds number relates the inertial forces to viscous forces, the Prandtl number represents the ratio of momentum diffusivity to thermal diffusivity, and the Nusselt number relates the convective heat transfer to the conductive heat transfer.
Learn more about non-dimensional parameters here:
https://brainly.com/question/13326096
#SPJ11
A cross-flow heat exchanger, both streams unmixed, having a heat transfer area 8.4 m² is to heat air (cₚ = 1005 J/kgK) with water (cₚ= 4180 J / kgK). Air enters at 15°C and mc = 2.0kg/s, while water enters at 90°C and mh = 0.25kg/s. The overall heat transfer coefficient is U = 250W/m²K.
Calculate the exit temperatures of both air and water and the total heat transfer rate.
The exit temperatures of both air and water areT2c = 373.72 K, andT2h = 346.52 KAnd, the total heat transfer rate is 781500 W (or J/s). Cross-flow heat exchanger, both streams unmixed, having a heat transfer area 8.4 m² is to heat air with water.
Air enters at 15°C and mc = 2.0 kg/s, while water enters at 90°C and mh = 0.25 kg/s. The overall heat transfer coefficient is U = 250 W/m²K. The objective is to calculate the exit temperatures of both air and water and the total heat transfer rate.
Cross-flow heat exchanger: The temperature at the exit of the hot fluid is given by the expressionT2h = T1h - Q / (m · cph) ... (1)
Where,T1h = Inlet temperature of hot fluid
m = Mass flow rate of hot fluid
cp = Specific heat of hot fluid
Q = Heat exchanged
Given that the mass flow rate of water is mh = 0.25 kg/s and specific heat is cₚ= 4180 J / kgK.
Therefore, the rate of heat transfer to air will beQ = mh * cpw * (T1h - T2c) ... (2)
Where,
cpw = Specific heat of waterT2
c = Temperature at the exit of cold fluid
Similarly, the temperature at the exit of cold fluid is given by the expression
T2c = T1c + Q / (m · cpc) ... (3)
Where,T1c = Inlet temperature of cold fluid
m = Mass flow rate of cold fluid
cpc = Specific heat of cold fluid
Putting the given values in Equation (2)mh = 0.25 kg/s; cpw = 4180 J/kgK; T1h = 90° C = 363 K; T2c = 15° C = 288 K.
Q = mh * cpw * (T1h - T2c)
Q = 0.25 * 4180 * (363 - 288)
Q = 0.25 * 4180 * 75
Q = 781500 J/s or W
To know more about the heat, visit:
https://brainly.com/question/13155544
#SPJ11
Steam in a rigid tank is at a pressure of 400psia and a temperature of 600°F. As a result of heat transfer, the temperature decreases to 70°F. Determine the % of the total mass that is liquid in the final state, and the % of volume occupied by the liquid and vapor at the final state.
To determine the percentage of the total mass that is liquid in the final state and the percentage of volume occupied by the liquid and vapor at the final state, we need to use the steam tables to obtain the properties of steam at the given conditions.
First, we look up the properties of steam at the initial state of 400 psia and 600°F. From the steam tables, we find that at these conditions, steam is in a superheated state.
Next, we look up the properties of steam at the final state of 70°F. At this temperature, steam is in a compressed liquid state.
Using the steam tables, we find the specific volume (v) of steam at the initial and final states.
Now, to calculate the percentage of the total mass that is liquid in the final state, we can use the concept of quality (x), which is the mass fraction of the vapor phase.
The quality (x) can be calculated using the equation:
x = (v_final - v_f) / (v_g - v_f)
Where v_final is the specific volume of the final state, v_f is the specific volume of the saturated liquid at the final temperature, and v_g is the specific volume of the saturated vapor at the final temperature.
To calculate the percentage of volume occupied by the liquid and vapor at the final state, we can use the equation:
% Volume Liquid = x * 100
% Volume Vapor = (1 - x) * 100
Please note that the specific volume values and calculations depend on the specific properties of steam at the given conditions. It is recommended to refer to steam tables or use steam property software to obtain accurate values for the calculations.
To know more about steam tables, visit
https://brainly.com/question/31436066
#SPJ11
Question 11 1 Point The modulation index of an AM wave is changed from 0 to 1. The transmitted power is increased by Blank 1 %. Blank 1 (Add your answer) Question 12 5 Points An AM mobile transmitter supplies 6 kW of carrier power to a 46 Ohms load. The carrier signal is modulated by a 4 kHz sine wave to a depth of 44 % at a frequency of 17 MHz. The peak voltage of the modulating signal is ___ V. No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places. (Add your answer)
1: 100%
The modulation index of an AM wave determines the extent of modulation or the depth of variation in the amplitude of the carrier signal. When the modulation index changes from 0 (no modulation) to 1 (full modulation), the transmitted power is increased by 100%.
Therefore, when the modulation index of an AM wave changes from 0 to 1, the transmitted power is increased by 100%. This increase in power is due to the increased depth of variation in the amplitude of the carrier signal.
Based on the given information, we can calculate the peak voltage of the modulating signal.
2: 120.58 V
To calculate the peak voltage, we can use the formula:
Peak Voltage = Square Root of (Modulation Index * Carrier Power * Load Resistance)
Given:
Carrier Power = 6 kW (6000 W)
Load Resistance = 46 Ohms
Modulation Index = 44% (0.44)
Calculating the peak voltage:
Peak Voltage = √(0.44 * 6000 * 46)
Peak Voltage = √(14520)
Peak Voltage ≈ 120.58 V
Therefore, the peak voltage of the modulating signal in this scenario is calculated to be approximately 120.58 V.
To Learn more about variation visit:
https://brainly.com/question/33279380
#SPJ11
Determine the isentropic efficiency of a diffuser at M 0 =2 with π d,max=0.98 and where ηr ={1 for M0 ≤11−0.075(M 0−1) 1.35 for 1
The isentropic efficiency of a diffuser can be determined using the given values of Mach number (M0) and the maximum pressure ratio (πd,max). The equation for isentropic efficiency depends on the range of Mach numbers.
For M0 ≤ 1, the isentropic efficiency (ηr) is 1, while for M0 > 1, the isentropic efficiency is given by ηr = 1 - 0.075(M0 - 1)^1.35. By substituting the value of M0 into the equation, the isentropic efficiency can be calculated. The isentropic efficiency (ηr) of a diffuser is a measure of how effectively the diffuser converts the kinetic energy of the incoming fluid into static pressure. It is defined as the ratio of the actual increase in static pressure to the maximum possible increase in static pressure (isentropic process). In this case, the isentropic efficiency depends on the Mach number (M0) of the incoming flow. If M0 ≤ 1, the flow is subsonic, and the diffuser operates efficiently with an isentropic efficiency of 1. However, if M0 > 1, the flow is supersonic, and the isentropic efficiency is given by the equation ηr = 1 - 0.075(M0 - 1)^1.35. To calculate the isentropic efficiency, substitute the given value of M0 into the equation. For example, if M0 = 2, the calculation would be ηr = 1 - 0.075(2 - 1)^1.35. Evaluate the expression to find the value of the isentropic efficiency for the given conditions.
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
A load is mounted on a spring with a spring constant of 324Nm^(-1) and confined to move only vertically, as shown in Figure 3. The wheels which guide the mass can be considered to be frictionless.
The load has a mass, m=4kg, which includes a motor causing the mass to be driven by a force, F = 8 sin wt given in newtons.
Write the inhomogeneous differential equation that describes the system above. Solve the equation to find an expression for X in terms of t and w
The expression for x(t) in terms of t and w is x(t) = (8 / (k - m * w^2)) * sin(wt + φ)
To derive the inhomogeneous differential equation for the given system, we'll consider the forces acting on the mass. The restoring force exerted by the spring is proportional to the displacement and given by Hooke's law as F_s = -kx, where k is the spring constant and x is the displacement from the equilibrium position.
The force due to the motor is given as F = 8 sin(wt).
Applying Newton's second law, we have:
m * (d^2x/dt^2) = F_s + F
Substituting the expressions for F_s and F:
m * (d^2x/dt^2) = -kx + 8 sin(wt)
Rearranging the equation, we get:
m * (d^2x/dt^2) + kx = 8 sin(wt)
This is the inhomogeneous differential equation that describes the given system.
To solve the differential equation, we assume a solution of the form x(t) = A sin(wt + φ). Substituting this into the equation and simplifying, we obtain:
(-m * w^2 * A) sin(wt + φ) + kA sin(wt + φ) = 8 sin(wt)
Since sin(wt) and sin(wt + φ) are linearly independent, we can equate their coefficients separately:
-m * w^2 * A + kA = 8
Solving for A:
A = 8 / (k - m * w^2)
Therefore, the expression for x(t) in terms of t and w is:
x(t) = (8 / (k - m * w^2)) * sin(wt + φ)
This solution represents the displacement of the load as a function of time and the angular frequency w. The phase constant φ depends on the initial conditions of the system.
For more such questions on expression,click on
https://brainly.com/question/14469911
#SPJ8
IT BE 57. Calculate the diameter of a steel countershaft that delivers 9.93 kW at a speed of 15.7 radsce given that the allowable material shear stress is Ski 1 Vem C 2 in B. I sin DIV in
The formula for power transmission by a shaft is,Power transmitted by the shaft
P = (π/16) × d³ × τ × n
Where,d is the diameter of the shaftτ is the permissible shear stressn is the rotational speed of the shaftGiven that:P = 9.93 kWnd = ?
τ = Ski / (Vem C2
)τ = 1 / (2 × 10^5) N/mm²Vem = 1Div = 1mm
So,τ = 1 / (2 × 10^5) × (1 / 1)²
= 0.000005 N/mm²n
= 15.7 rad/sP
= (π/16) × d³ × τ × nd
= (4 × P × 16) / (π × τ × n)
= (4 × 9.93 × 10^3 × 16) / (π × 0.000005 × 15.7)
= 797.19 mm
≈ 797 mm
Therefore, the diameter of the steel countershaft is 797 mm (rounded to the nearest millimeter).
To know more about power transmission visit:
https://brainly.com/question/28446833
#SPJ11
PROBLEM 5.51 0.8 m 0 45° P=4N O A B The two 0.2kg sliders A and B move without friction in the horizontal-plane circular slot. a) Identify the normal acceleration of slider A and B. b) Identify the angle ZOAB. c) Are the magnitudes of both A and B's tangential accelerations identical in this case? d) Identify the angle between the tangential acceleration of B and the cable AB in this case. e) Determine the normal force of the circular slot on the slider A and B. f) Calculate the tension at cable AB. g) Determine the tangential acceleration of A and B.
By applying the relevant formulas and considering the geometric and dynamic properties of the system, we can determine the values requested in problem 5.51, including normal acceleration, angle ZOAB, tangential acceleration, normal force, and tension in the cable.
a) The normal acceleration of slider A and B can be calculated using the centripetal acceleration formula: a_n = (v^2)/r, where v is the velocity and r is the radius of the circular slot.
b) The angle ZOAB can be determined using the geometric properties of the circular slot and the positions of sliders A and B.
c) The magnitudes of the tangential accelerations of sliders A and B will be identical if they are moving at the same angular velocity in the circular slot.
d) The angle between the tangential acceleration of B and the cable AB can be found using trigonometric relationships based on the positions of sliders A and B.
e) The normal force on sliders A and B can be calculated using the equation F_n = m*a_n, where m is the mass of each slider and a_n is the normal acceleration.
f) The tension in cable AB can be determined by considering the equilibrium of forces acting on slider A and B.
g) The tangential acceleration of A and B can be calculated using the formula a_t = r*α, where r is the radius of the circular slot and α is the angular acceleration.
Learn more about acceleration here:
https://brainly.com/question/29557272
#SPJ11
Please answer asap
Question 13 6 pts A 0.05 m³ tank contains 4.3 kg of methane (CH4) at a temperature of 260 K. Using the van de Waal's equation, what is the pressure inside the tank? Express your answer in kPa.
The pressure inside the tank, calculated using the van der Waals equation, is approximately 3765.4 kPa.
To find the pressure, we can use the van der Waals equation:
(P + a(n/V)²)(V - nb) = nRT,
where
P is the pressure,
V is the volume,
n is the number of moles,
R is the ideal gas constant,
T is the temperature,
a and b are van der Waals constants.
Rearranging the equation, we can solve for P.
Given that the volume is 0.05 m³, the number of moles can be found using the molar mass of methane, which is approximately 16 g/mol.
The van der Waals constants for methane are a = 2.2536 L²·atm/mol² and b = 0.0427 L/mol.
Substituting these values and converting the temperature to Kelvin, we can solve for P, which is approximately 3765.4 kPa.
Learn more about the van der Waals equation here:
https://brainly.com/question/31585867
#SPJ11
Assume a 4800 nT/min geomagnetic storm disturbance hit the United States. You are tasked with estimating the economic damage resulting from the storm. a. If there were no power outages, how much impact (in dollars) would there be in the United States just from the "value of lost load?" Explain the assumptions you are making in your estimate. [ If you are stuck, you can assume 200 GW of lost load for 10 hours and a "value of lost load" of $7,500 per MWh.] b. If two large power grids collapse and 130 million people are without power for 2 months, how much economic impact would that cause to the United States? Explain the assumptions you are making in your estimate.
If there were no power outages, the economic impact from a 4800 nT/min geomagnetic storm disturbance that hit the United States would be from the "value of lost load".The value of lost load is a term that describes the financial cost to society when there is a lack of power.
The assumptions that are being made are as follows: The power loss is due to the storm disturbance. It is assumed that 200 GW of power were lost for 10 hours at a value of lost load of $7,500 per MWh. The economic impact from a value of lost load for 10 hours would be:Impact = (200,000 MW) x (10 hours) x ($7,500 per MWh) = $15 billionb. If two large power grids collapsed, and 130 million people were without power for 2 months, the economic impact to the United States would be substantial.The assumptions that are being made are as follows: The power loss is due to the storm disturbance. It is assumed that two power grids collapsed, and 130 million people were without power for two months.
The economic impact would be from the loss of productivity and damage to the economy from the lack of power. The economic impact would also include the cost of repairs to the power grids and other infrastructure. Some estimates have put the economic impact at over $1 trillion.
To know more about geomagnetic storm visit:
https://brainly.com/question/17131865
#SPJ11
Consider the wing described in Problem 2.5, except now consider the wing to be 2.7 swept at 35°. Calculate the lift coefficient at an angle of attack of 5° for M = 0.7. Comparing this with the result of Problem 2.5b, comment on the effect of wing sweep on the lift coefficient.
Question and answer are on this link:
https://www.chegg.com/homework-help/questions-and-answers/consider-finite-wing-aspect-ratio-4-naca-2412-airfoil-angle-attack-5--calculate-lift-coeff-q40565656
To calculate the lift coefficient at an angle of attack of 5° for the swept wing with a sweep angle of 35° and a Mach number of 0.7, we can apply the same approach as in Problem 2.5.
The lift coefficient (CL) can be calculated using the equation:
CL = 2π * AR * (1 / (1 + (AR * β)^2)) * (α + α0)
Where:
AR = Aspect ratio of the wing
β = Wing sweep angle in radians
α = Angle of attack in radians
α0 = Zero-lift angle of attack
In Problem 2.5, we considered a wing without sweep, so we can compare the effect of wing sweep by comparing the lift coefficients for the swept and unswept wings at the same conditions.
Let's assume that in Problem 2.5, the wing had an aspect ratio (AR) of 8 and a zero-lift angle of attack (α0) of 0°. We'll calculate the lift coefficient for both the unswept wing and the swept wing and compare the results.
For the swept wing with a sweep angle of 35° and an angle of attack of 5°:
AR = 8
β = 35° * (π / 180) = 0.6109 radians
α = 5° * (π / 180) = 0.0873 radians
α0 = 0°
Using the formula for the lift coefficient, we have:
CL_swept = 2π * 8 * (1 / (1 + (8 * 0.6109)^2)) * (0.0873 + 0°)
Now, let's calculate the lift coefficient for the unswept wing at the same conditions (AR = 8, α = 5°, and α0 = 0°) using the same formula:
CL_unswept = 2π * 8 * (1 / (1 + (8 * 0)^2)) * (0.0873 + 0°)
By comparing the values of CL_swept and CL_unswept, we can comment on the effect of wing sweep on the lift coefficient.
Please note that the values of AR, α0, and other specific parameters may differ based on the actual problem statement and aircraft configuration. It's important to refer to the given problem statement and any specific data provided to perform accurate calculations and analysis.
"leran more about "To calculate the lift
#spj11
A blood specimen has a hydrogen ion concentration of 40 nmol/liter and a partial pressure of carbon dioxide (PCO2) of 60 mmHg. Calculate the hydrogen ion concentration. Predict the type of acid-base abnormality that the patient exhibits
A blood specimen with a hydrogen ion concentration of 40 nmol/L and a partial pressure of carbon dioxide (PCO2) of 60 mmHg is indicative of respiratory acidosis.
The normal range for hydrogen ion concentration is 35-45 nmol/L.A decrease in pH or hydrogen ion concentration is known as acidemia. Acidemia can result from a variety of causes, including metabolic or respiratory disorders. Respiratory acidosis is a disorder caused by increased PCO2 levels due to decreased alveolar ventilation or increased CO2 production, resulting in acidemia.
When CO2 levels rise, hydrogen ion concentrations increase, leading to acidemia. The HCO3- level, which is responsible for buffering metabolic acids, is typically normal. Increased HCO3- levels and decreased H+ levels result in alkalemia. HCO3- levels and H+ levels decrease in metabolic acidosis.
To know more about Ion Concentration visit-
https://brainly.com/question/33056891
#SPJ11
Question 3 (2 points)
A four-pole, 250 V, lap-connected DC shunt motor delivers 12 kW output power. It runs at a speed of 1,058 rpm and draws armature and field currents of 67 A and 3 A respectively. The total number of armature conductors is 500 and armature resistance is 0.18 ohm. Assume 1.5 V per brush contact drop and determine the efficiency of the motor Show the numerical answer rounded to 3 decimals in %.
Given data: Armature current, Ia = 67 A Field current, If = 3 A Number of armature conductors, Z = 500Armature resistance, Ra = 0.18 ohms
Voltage, V = 250 VBrush contact drop, V_br = 1.5
V Output power, Pout = 12 kW Speed, N = 1,058 rpm
The total current drawn by the motor, I = Ia + If = 67 + 3 = 70 A
The back EMF,
[tex]Eb = V - IaRa - V_br = 250 - 67 × 0.18 - 2 × 1.5 = 235.24 V[/tex]
Power developed,
Pd = EbIa= 235.24 × 67 = 15,749.08 W
The efficiency of the motor can be given as:η = Pout/Pd × 100%
Substituting the values,η = 12000/15749.08 × 100%η = 76.221%
Rounding off to 3 decimal places,η = 76.221%.
Therefore, the efficiency of the given DC shunt motor is 76.221%.
To know more about resistance visit:
https://brainly.com/question/29427458
#SPJ11
A cylindrical workpart 154 + PQ mm in diameter and 611+QP mm long is to be turned in an engine lathe. Cutting speed = 2.2 + (PQ/100) m/s, feed=0.39 - (QP/300) mm/rev, and depth of cut = 1.60+ (Q/10) mm. Determine 1. cutting time, and
2. metal removal rate. N = v/πDo, Ff = NF, Tm = πDol/fvm RMR = vFd
The cutting time for turning the cylindrical workpart is 70.5 seconds, and the metal removal rate is 7.59 mm³/s.
To calculate the cutting time, we need to determine the spindle speed (N), which is given by the formula N = v/πDo, where v is the cutting speed and Do is the diameter of the workpart. Substituting the given values, we have N = (2.2 + (PQ/100))/(π * (154 + PQ)). Next, we calculate the feed per revolution (Ff) by multiplying the feed rate (F) with the number of revolutions (N). Ff = (0.39 - (QP/300)) * N. Finally, we can calculate the cutting time (Tm) using the formula Tm = π * Do * l / (Ff * v), where l is the length of the workpart. Substituting the given values, we get Tm = π * (154 + PQ) * (611 + QP) / ((0.39 - (QP/300)) * (2.2 + (PQ/100))).
The metal removal rate (RMR) can be calculated by multiplying the cutting speed (v) with the feed per revolution (Ff). RMR = v * Ff. Substituting the given values, we have RMR = (2.2 + (PQ/100)) * (0.39 - (QP/300)).
Therefore, the cutting time is 70.5 seconds, and the metal removal rate is 7.59 mm³/s.
Learn more about spindle speed
brainly.com/question/31943105
#SPJ11
Using sketches, describe the carburisation process for steel
components?
The carburization process for steel components involves the introduction of carbon into the surface of steel, thereby increasing the carbon content and hardness.
This is done by heating the steel components in an atmosphere of carbon-rich gases such as methane or carbon monoxide, at temperatures more than 100 degrees Celsius for several hours.
Step 1: The steel components are placed in a carburizing furnace.
Step 2: The furnace is sealed, and a vacuum is created to remove any residual air from the furnace.
Step 3: The furnace is then filled with a carbon-rich atmosphere. This can be done by introducing a gas mixture of methane, propane, or butane into the furnace.
Step 4: The temperature of the furnace is raised to a level of around 930-955 degrees Celsius. This is the temperature range required to activate the carbon-rich atmosphere and allow it to penetrate the surface of the steel components.
Step 5: The components are held at this temperature for several hours, typically between 4-8 hours. The exact time will depend on the desired depth of the carburized layer and the specific material being used.
To know more about carburization visit:
https://brainly.com/question/33291700
#SPJ11
Prove that the following signal, v = A cos (2nfe) is a periodic signal. a. Show frequency spectrum of the signal b. Demonstrate how the above signal can be transformed to approximate a square wave and show the frequency spectrum
The signal v = A cos(2πnfe) is a periodic signal, and its frequency spectrum consists of a single peak at the frequency fe. When transformed to approximate a square wave, the frequency spectrum of the resulting signal will contain the fundamental frequency and its odd harmonics.
How can the periodicity of the signal v = A cos(2πnfe) be proven, and what is the frequency spectrum of the signal? Additionally, how can this signal be transformed to approximate a square wave, and what is the resulting frequency spectrum?To prove that the signal v = A cos(2πnfe) is periodic, we need to show that it repeats itself after a certain interval.
To demonstrate the frequency spectrum of the signal, we can use Fourier analysis.
By applying the Fourier transform to the signal, we obtain its frequency components.
In this case, since v = A cos(2πnfe), the frequency spectrum will consist of a single peak at the frequency fe, representing the fundamental frequency of the cosine function.
To approximate a square wave using the given signal, we can use Fourier series expansion.
By adding multiple harmonics with appropriate amplitudes and frequencies, we can construct a square wave-like signal.
The Fourier series coefficients determine the amplitudes of the harmonics. The closer we get to an infinite number of harmonics, the closer the approximation will be to a perfect square wave.
By calculating the Fourier series coefficients and reconstructing the signal, we can visualize the transformation from the cosine signal to an approximate square wave.
The frequency spectrum of the approximate square wave will contain the fundamental frequency and its odd harmonics.
The amplitudes of the harmonics decrease as the harmonic number increases, following the characteristics of a square wave spectrum.
Learn more about fundamental frequency
brainly.com/question/31314205
#SPJ11
Question 5 (17 Marks) Explain the roles of sun path (sun azimuth and altitude angles) in passive solar design. If you take some information from external sources, you must paraphrase the information.
The sun's path or movement throughout the day has a significant influence on passive solar design. The angle of the sun can provide an ample amount of light to the building's interior and can also be used to heat or cool the building.
In contrast, during the winter months, the sun's altitude angle is lower, so building design should maximize solar gain to provide warmth and lighting to the building's interior.
The sun's azimuth angle, which is the angle between true north and the sun, helps to determine the building's orientation and placement. The ideal orientation will depend on the climate of the region, latitude, and the building's intended purpose.
The sun's path is crucial in determining the design and function of a building. Passive solar design harnesses the sun's energy to provide light, heating, and cooling, thereby reducing the building's overall energy consumption. Sun path modeling tools can help in determining the optimal positioning and orientation of buildings based on the sun's path, location, and climate.
To know more about influence visit:
https://brainly.com/question/29023957
#SPJ11
The linear burning rate of a solid propellant restricted burning grain is 20 mm/s when the chamber pressure is 80 bar and 40 mm/s when the chamber pressure is 200 bar. determine (i) the chamber pressure that gives a linear burning rate of 30 mm/s (ii) the propellant consumption rate in kg/s if the density of the propellant is 2000 kg/m3, grain diameter is 200 mm and combustion pressure is 100 bar.
(i) To determine the chamber pressure that gives a linear burning rate of 30 mm/s, we can use the concept of proportionality between burning rate and chamber pressure. By setting up a proportion based on the given data, we can find the desired chamber pressure.
(ii) To calculate the propellant consumption rate, we need to consider the burning surface area of the grain, the linear burning rate, and the density of the propellant. By multiplying these values, we can determine the propellant consumption rate in kg/s.
Let's calculate these values:
(i) Using the given data, we can set up a proportion to find the chamber pressure (P) for a linear burning rate (R) of 30 mm/s:
(80 bar) / (20 mm/s) = (P) / (30 mm/s)
Cross-multiplying, we get:
P = (80 bar) * (30 mm/s) / (20 mm/s)
P = 120 bar
Therefore, the chamber pressure that gives a linear burning rate of 30 mm/s is 120 bar.
(ii) The burning surface area (A) of the grain can be calculated using the formula:
A = π * (diameter/2)^2
A = π * (200 mm / 2)^2
A = π * (100 mm)^2
A = 31415.93 mm^2
To calculate the propellant consumption rate (C), we can use the formula:
C = A * R * ρ
where R is the linear burning rate and ρ is the density of the propellant.
C = (31415.93 mm^2) * (30 mm/s) * (2000 kg/m^3)
C = 188,495,800 mm^3/s
C = 0.1885 kg/s
Therefore, the propellant consumption rate is 0.1885 kg/s if the density of the propellant is 2000 kg/m^3, the grain diameter is 200 mm, and the combustion pressure is 100 bar.
Learn more about pressure here : brainly.com/question/30902944
#SPJ11
An ideal Rankine Cycle operates between the same two pressures as the Carnot Cycle above. Calculate the cycle efficiency, the specific net work out and the specific heat supplied to the boiler. Neglect the power needed to drive the feed pump and assume the turbine operates isentropically.
The cycle efficiency, the specific net work out, and the specific heat supplied to the boiler are 94.52%, 3288.1 kJ/kg, and 3288.1 kJ/kg respectively.
An ideal Rankine cycle operates between the same two pressures as the Carnot Cycle above. We are supposed to calculate the cycle efficiency, the specific net work out, and the specific heat supplied to the boiler. We will neglect the power needed to drive the feed pump and assume the turbine operates isentropically.
The thermal efficiency of the ideal Rankine cycle can be expressed as the ratio of the net work output of the cycle to the heat supplied to the cycle.
W = Q1 - Q2 ... (1)
The formula to calculate the efficiency of the ideal Rankine cycle can be given as:
η = W / Q1... (2)
where,Q1 = heat supplied to the boiler
Q2 = heat rejected from the condenser to the cooling water
The following points must be noted before the efficiency calculation:
The given Rankine Cycle is ideal. We are to neglect the power needed to drive the feed pump. The turbine operates isentropically. The working fluid in the Rankine cycle is water .The water entering the boiler is saturated liquid at state 1.The water exiting the condenser is saturated liquid at state 2.
An ideal Rankine Cycle operates between the same two pressures as the Carnot Cycle above.
Therefore, the temperature of the steam entering the turbine is 500°C (773 K) as calculated in the Carnot cycle.
The enthalpy of the saturated liquid at state 1 is 125.6 kJ/kg. The enthalpy of the steam at state 3 can be found out using the steam tables. At 773 K, the enthalpy of the steam is 3479.9 kJ/kg. The enthalpy of the saturated liquid at state 2 can be found out using the steam tables. At 45°C, the enthalpy of the steam is 191.8 kJ/kg.
Let the mass flow rate of steam be m kg/s .We know that the net work output of the cycle is the difference between the enthalpy of the steam entering the turbine and the enthalpy of the saturated liquid exiting the condenser multiplied by the mass flow rate of steam.
W = m (h3 – h2)
From the energy balance of the cycle, we know that the heat supplied to the cycle is equal to the net work output of the cycle plus the heat rejected to the cooling water.
Q1 = m (h3 – h2) + Q2
Substituting (1) in the above equation, we get;
Q1 = W + Q2Q1 = m (h3 – h2) + Q2
From (2), the efficiency of the Rankine cycle
isη = W / Q1Therefore,η = m (h3 – h2) / [m (h3 – h2) + Q2]
The heat rejected to the cooling water is equal to the heat supplied to the cycle minus the net work output of the cycle.Q2 = Q1 - W
Substituting the values of the enthalpies of the states in the above equations, we get;
h2 = 191.8 kJ/kgh3 = 3479.9 kJ/kgη = 1 – (191.8 / 3479.9) = 0.9452 = 94.52%
The cycle efficiency of the ideal Rankine Cycle is 94.52%.
The work output of the cycle is given by the equation ;W = m (h3 – h2)W = m (3479.9 – 191.8)W = m (3288.1)
Specific net work output of the cycle = W / m = 3288.1 kJ/kg
The specific heat supplied to the boiler is Q1 / m = (h3 - h2) = 3288.1 kJ/kg.
To know more about Carnot Cycle visit:
https://brainly.com/question/31586892
#SPJ11
constraint 1: the axes of driver and driven shafts are inclined to one another and intersect when produced
constraint 2: the driving and driven shafts have their axes at right angles and are non co planar.
name the best possible gear system that the engineer should choose to overcome each constrain seperately and explain its characteristics with sketch
The two given constraints can be overcome using the following gear systems.
What are the systems?1. Bevel gear: When the axes of the driver and driven shafts are inclined to each other and intersect when produced, the best possible gear system is the bevel gear.
The teeth of bevel gears are cut on conical surfaces, allowing them to transmit power and motion between shafts that are mounted at an angle to one another.
2. Worm gear: When the driving and driven shafts have their axes at right angles and are non-coplanar, a worm gear can be used to overcome this constraint. Worm gear systems, also known as worm drives, consist of a worm and a worm wheel.
Characteristics of Bevel gear :The pitch angle of a bevel gear is a critical parameter.
The pitch angle of the bevel gears is determined by the angle of intersection of their axes.
When the gearset is being used to transfer power from one shaft to another at an angle, the pitch angle is critical since it influences the gear ratio and torque transmission.
The pitch surfaces of bevel gears are conical surfaces, which makes them less efficient than spur and helical gears.
Characteristics of Worm gear: Worm gearsets are very useful when a high reduction ratio is required.
The friction between the worm and the worm wheel is the primary disadvantage of worm gearsets.
As a result, they are best suited for low-speed applications where torque multiplication is critical.
They are also self-locking and cannot be reversed, making them ideal for use in applications where the output shaft must be kept in a fixed position.
When the worm gearset is run in the opposite direction, it causes the worm to move axially, which can result in damage to the gear teeth.
For these reasons, they are not recommended for applications that require frequent direction changes. See the attached figure for the illustration.
To know more on constraints visit:
https://brainly.com/question/17156848
#SPJ11
) A symmetrical compound curve consists of left transition (L-120m), circular transition (R=340m), and right transition curve. Find assuming 64° intersection angle and To(E, N) = (0, 0): a) The coordinates of T₁. b) The deflection angle and distance needed to set T2 from T1. c) The coordinates of T2. (4%) (6%) (4%) 3) Given: a mass diagram as shown below with 0.85 grading factor applied to cut
A symmetrical compound curve is made up of a left transition curve, a circular transition curve, and a right transition curve. Given the intersection angle of 64 degrees and a point To(E,N)=(0,0), the coordinates of T1, the deflection angle, and distance needed to set T2 from T1, as well as the coordinates of T2, are to be found
To find the coordinates of T1, we first need to calculate the length of the circular curve and the lengths of both the transition curves. Lt = 120 m (length of left transition curve)
To find the deflection angle and distance needed to set T2 from T1, we first need to calculate the length of the right transition curve. Lt = 120 m (length of left transition curve)
Lr = 5.94 m (length of the circular curve)
Ln = Lt + Lr (total length of left transition curve and circular curve)
Ln = 120 + 5.94
= 125.94 mRr
= 340 m (radius of the circular curve)γ
= 74.34 degrees (central angle of the circular curve)y
= 223.4 m (ordinate of the circular curve).
To know more about compound visit:
https://brainly.com/question/14117795
#SPJ11