The air streams over the wings are disturbed when the angle of attack is reached. The air in the lower part of the wing is relatively undisturbed, whereas the air in the upper part is more disturbed. As a result of the separation, the wing produces less lift, and the drag increases.
1. Stall angle of attack: Stall angle of attack refers to the angle of attack where the wing's lift coefficient starts to decrease rapidly. At this angle of attack, the airflow over the wing's upper surface separates from the wing's surface, resulting in a decrease in lift and an increase in drag.
2. Lifting Principle: According to the Coanda effect, a fluid, when flowing over the curved surface of an object, tends to follow the surface rather than continue flowing in a straight line. The curvature of the wing's upper surface causes the airflow to follow the surface.
3. Equal time principle: According to the equal time principle, air flowing over the top of a wing and air flowing over the bottom of a wing must meet at the back of the wing at the same time. This theory is incorrect because it does not account for the wing's curvature and the Coanda effect.
4. Wind Tunnel Experiment: In a wind tunnel experiment to measure lift and drag coefficients versus the angle of attack, a model of the wing is mounted in the wind tunnel and subjected to varying airspeeds at different angles of attack. By measuring the forces generated on the wing, the lift and drag coefficients can be determined.
The plot of the lift coefficient versus the angle of attack is shaped like an elongated S curve, while the plot of the drag coefficient versus the angle of attack is shaped like a U curve.
To know more about produces visit:
https://brainly.com/question/30698459
#SPJ11
The total mass of the table of a planning machine and its attached work piece is 350 kg. The table is traversed by a single-start square thread of external diameter 45 mm and pitch 10 mm. The pressure of the cutting is 600 N and the speed of cutting is 6 meters per minute. The coefficient of friction for the table is 0.1 and for the screw thread is 0.08. Find the power required.
The power required for the planning machine is 1,11,960 N·m/min.
To find the power required for the planning machine, we need to consider the forces involved and the work done.
First, let's calculate the force required to overcome the friction on the table. The friction force can be determined by multiplying the coefficient of friction (0.1) by the weight of the table and the attached workpiece (350 kg * 9.8 m/s^2):
Friction force = 0.1 * 350 kg * 9.8 m/s^2 = 343 N
Next, we need to calculate the force required to move the table due to the screw thread. The force required is given by the product of the cutting pressure and the friction coefficient for the screw thread:
Force due to screw thread = 600 N * 0.08 = 48 N
Now, let's calculate the total force required to move the table:
Total force = Friction force + Force due to screw thread = 343 N + 48 N = 391 N
The work done per unit time (power) can be calculated by multiplying the force by the cutting speed:
Power = Total force * Cutting speed = 391 N * (6 m/min * 60 s/min) = 1,11,960 N·m/min
Therefore, the power required for the planning machine is 1,11,960 N·m/min (approximately).
For more such questions on power,click on
https://brainly.com/question/29898571
#SPJ8
determine the 1st order different equation relating to Vc to the
inputs.
Determine the 1st order differential equ to relating Осто (t >0) the + 20v inputs. 1/2 F 12 201 + vc Зол 1 605 n LA t=0 7V
To determine the 1st order differential equation relating Vc to the inputs, we use the following formula:
[tex]$$RC \frac{dV_c}{dt} + V_c = V_i$$[/tex]
where RC is the time constant of the circuit, Vc is the voltage across the capacitor at time t, Vi is the input voltage, and t is the time.
Since we are given that the inputs are 20V and the capacitor voltage at t = 0 is 7V, we can substitute these values into the formula to obtain:
[tex]$$RC \frac{dV_c}{dt} + V_c = V_i$$$$RC \frac{dV_c}{dt} + V_c = 20V$$[/tex]
Also, at t = 0, the voltage across the capacitor is given as 7V, hence we have:[tex]$$V_c (t=0) = 7V$$[/tex]
Therefore, to obtain the first order differential equation relating Vc to the inputs, we substitute the values into the formula as shown below:
[tex]$$RC \frac{dV_c}{dt} + V_c = 20V$$[/tex]and the initial condition:[tex]$$V_c (t=0) = 7V$$[/tex]where R = 201 ohms, C = 1/2 F and the time constant, RC = 100.5 s
Thus, the 1st order differential equation relating Vc to the inputs is:[tex]$$100.5 \frac{dV_c}{dt} + V_c = 20V$$$$\frac{dV_c}{dt} + \frac{V_c}{100.5} = \frac{20}{100.5}$$$$\frac{dV_c}{dt} + 0.0995V_c = 0.1990$$[/tex]
To know more about differential visit:
https://brainly.com/question/31383100
#SPJ11
Question 3: Explain in your own words what happens with the energy terms for a stone falling from a height into a bucket of water. Assume the water and stone are at the same temperature, which is higher than the surrounding temperature. What would happen if the object was a bouncing ball falling to a hard surface?
When a stone is dropped from a certain height into a bucket of water, it undergoes a potential to kinetic energy conversion. When the stone is lifted, it possesses a certain amount of potential energy due to its position. This energy is converted into kinetic energy as the stone starts falling towards the water.
At the same time, the water exerts an opposing force against the stone, which leads to a decrease in its kinetic energy. When the stone finally hits the water, the kinetic energy gets converted into sound and heat energy, causing a splash and a rise in temperature of the water.
In case a bouncing ball is dropped onto a hard surface, the potential energy is converted into kinetic energy as the ball falls towards the surface. Once it touches the surface, the kinetic energy is converted into potential energy. The ball bounces back up due to the elastic force exerted by the surface, which converts the potential energy into kinetic energy again. The process of conversion of potential to kinetic energy and back continues until the ball stops bouncing, and all its energy is dissipated in the form of heat.
To know more about potential energy visit :-
https://brainly.com/question/24284560
#SPJ11
Two normal stresses of equal magnitude of 5, but of opposite signs, act at an stress element in perpendicular directions x and y. The shear stress acting in the xy-plane at the plane is zero. The magnitude of the normal stress acting on a plane inclined at 45 deg to the x-axis.
O None of these
O 5/2
O 25
O 5/4
O 0
Given data: Normal stresses of equal magnitude = 5Opposite signs, Act at an stress element in perpendicular directions x and y.The shear stress acting in the xy-plane at the plane is zero. The plane is inclined at 45° to the x-axis.
Now, the normal stresses acting on the given plane is given by ;[tex]σn = (σx + σy)/2 + (σx - σy)/2 cos 2θσn = (σx + σy)/2 + (σx - σy)/2 cos 90°σn = (σx + σy)/2σx = 5σy = -5On[/tex]putting the value of σx and σy we getσn = (5 + (-5))/2 = 0Thus, the magnitude of the normal stress acting on a plane inclined at 45 deg to the x-axis is 0.Answer: The correct option is O 0.
To know more about plane visit:
https://brainly.com/question/2400767
#SPJ11
1A) Convert the denary number 47.40625 10
to a binary number. 1B) Convert the denary number 3714 10
to a binary number, via octal. 1C) Convert 1110011011010.0011 2
to a denary number via octal.
1A) The binary representation of 47.40625 is 101111.01110.
1B) The binary representation of 3714 via octal is 11101000010.
1C) The decimal representation of 1110011011010.0011 via octal is 1460.15625.
1A) To convert the decimal number 47.40625 to a binary number:
The whole number part can be converted by successive division by 2:
47 ÷ 2 = 23 remainder 1
23 ÷ 2 = 11 remainder 1
11 ÷ 2 = 5 remainder 1
5 ÷ 2 = 2 remainder 1
2 ÷ 2 = 1 remainder 0
1 ÷ 2 = 0 remainder 1
Reading the remainders from bottom to top, the whole number part in binary is 101111.
For the fractional part, multiply the fractional part by 2 and take the whole number part at each step:
0.40625 × 2 = 0.8125 (whole number part: 0)
0.8125 × 2 = 1.625 (whole number part: 1)
0.625 × 2 = 1.25 (whole number part: 1)
0.25 × 2 = 0.5 (whole number part: 0)
0.5 × 2 = 1 (whole number part: 1)
Reading the whole number parts from top to bottom, the fractional part in binary is 01110.
Combining the whole number and fractional parts, the binary representation of 47.40625 is 101111.01110.
1B) To convert the decimal number 3714 to a binary number via octal:
First, convert the decimal number to octal:
3714 ÷ 8 = 464 remainder 2
464 ÷ 8 = 58 remainder 0
58 ÷ 8 = 7 remainder 2
7 ÷ 8 = 0 remainder 7
Reading the remainders from bottom to top, the octal representation of 3714 is 7202.
Then, convert the octal number to binary:
7 = 111
2 = 010
0 = 000
2 = 010
Combining the binary digits, the binary representation of 3714 via octal is 11101000010.
1C) To convert the binary number 1110011011010.0011 to a decimal number via octal:
First, convert the binary number to octal by grouping the digits in sets of three from the decimal point:
11 100 110 110 100.001 1
Converting each group of three binary digits to octal:
11 = 3
100 = 4
110 = 6
110 = 6
100 = 4
001 = 1
1 = 1
Combining the octal digits, the octal representation of 1110011011010.0011 is 34664.14.
Finally, convert the octal number to decimal:
3 × 8^4 + 4 × 8^3 + 6 × 8^2 + 6 × 8^1 + 4 × 8^0 + 1 × 8^(-1) + 4 × 8^(-2)
= 768 + 256 + 384 + 48 + 4 + 0.125 + 0.03125
= 1460.15625
Therefore, the decimal representation of 1110011011010.0011 via octal is 1460.15625.
To know more about binary number visit:
https://brainly.com/question/13262331
#SPJ11
Question 3 20 Points (20) After inspection, it is found that there is an internal crack inside of an alloy with a full width of 0.4 mm and a curvature radius of 5x10-3 mm, and there is also a surface crack on this alloy with a full width of 0.1 mm and a curvature radius of 1x10-3 mm. Under an applied tensile stress of 50 MPa, • (a) What is the maximum stress around the internal crack and the surface crack? (8 points) • (b) For the surface crack, if the critical stress for its propagation is 900 MPa, will this surface crack propagate? (6 points) • (c) Through a different processing technique, the width of both the internal and surface cracks is decreased. With decreased crack width, how will the fracture toughness and critical stress for crack growth change? (6 points) Use the editor to format your answer
The maximum stress around the internal crack can be determined using the formula for stress concentration factor.
The stress concentration factor for an internal crack can be approximated as Kt = 3(1 + a/w)^(1/2), where a is the crack depth and w is the full width of the crack. Substituting the values, we get Kt = 3(1 + 0.4/5)^(1/2) ≈ 3.33. Therefore, the maximum stress around the internal crack is 3.33 times the applied stress, which is 50 MPa, resulting in approximately 166.5 MPa. Similarly, for the surface crack, the stress concentration factor can be approximated as Kt = 2(1 + a/w)^(1/2). Substituting the values, we get Kt = 2(1 + 0.1/1)^(1/2) = 2.1. Therefore, the maximum stress around the surface crack is 2.1 times the applied stress, which is 50 MPa, resulting in approximately 105 MPa. For the surface crack to propagate, the applied stress must exceed the critical stress for crack propagation. In this case, the critical stress for the surface crack is given as 900 MPa. Since the applied stress is only 50 MPa, which is lower than the critical stress, the surface crack will not propagate under the given conditions. When the width of both the internal and surface cracks is decreased through a different processing technique, the fracture toughness increases. A smaller crack width reduces the stress concentration and allows the material to distribute the applied stress more evenly. As a result, the material becomes more resistant to crack propagation, and the critical stress for crack growth increases. Therefore, by decreasing the crack width, the fracture toughness improves, making the material more resistant to cracking.
Learn more about crack propagation here:
https://brainly.com/question/31393555
#SPJ11
Calculate the volumetric efficiency of the compressor from Q2 if the unswept volume is 6% of the swept volume. Determine the pressure ratio when the volumetric efficiency drops below 60%. Take T1=T, and P1=Pa. [71%, 14.1]
The answer is 14.1. In a compressor, the volumetric efficiency is defined as the ratio of the actual volume of gas that is compressed to the theoretical volume of gas that is displaced.
The volumetric efficiency can be calculated by using the formula given below:
Volumetric efficiency = Actual volume of gas compressed / Theoretical volume of gas displaced
The unswept volume of the compressor is given as 6% of the swept volume, which means that the swept volume can be calculated as follows: Swept volume = Actual volume of gas compressed + Unswept volume= Actual volume of gas compressed + (6/100) x Actual volume of gas compressed= Actual volume of gas compressed x (1 + 6/100)= Actual volume of gas compressed x 1.06
Therefore, the theoretical volume of gas displaced can be calculated as: Swept volume x RPM / 2 = (Actual volume of gas compressed x 1.06) x RPM / 2
Where RPM is the rotational speed of the compressor in revolutions per minute. Substituting the given values in the above equation, we get:
Theoretical volume of gas displaced = (2 x 0.8 x 22/7 x 0.052 x 700) / 2= 1.499 m3/min
The actual volume of gas compressed is given as Q2 = 0.71 m3/min. Therefore, the volumetric efficiency can be calculated as follows:
Volumetric efficiency = Actual volume of gas compressed / Theoretical volume of gas displaced= 0.71 / 1.499= 0.474 or 47.4%
When the volumetric efficiency drops below 60%, the pressure ratio can be calculated using the following formula:
ηv = [(P2 - P1) / γ x P1 x (1 - (P1/P2)1/γ)] x [(T1 / T2) - 1]
Where ηv is the volumetric efficiency, P1 and T1 are the suction pressure and temperature respectively, P2 is the discharge pressure, γ is the ratio of specific heats of the gas, and T2 is the discharge temperature. Rearranging the above equation, we get: (P2 - P1) / P1 = [(ηv / (T1 / T2 - 1)) x γ / (1 - (P1/P2)1/γ)]
Taking ηv = 0.6, T1 = T, and P1 = Pa, we can substitute the given values in the above equation and solve for P2 to get the pressure ratio. The answer is 14.1.
To know more about volumetric efficiency refer to:
https://brainly.com/question/29250379
#SPJ11
The following measurements were made on a resistive two-port network: Condition 1 - create a short circuit at port 2 and apply 20 V to port 1: Measurements: I₁ = 1 A; I₂ = −1 A. Condition 2 - create an open circuit at port 1 and apply 80 V to port 2: Measurements: V₁ = 400 V; I₂ = 3 A. Part A Find the maximum power that this two-port circuit can deliver to a resistive load at port 2 when port 1 is driven by a 6 A dc current source with an internal resistance of 70 Ω Express your answer with the appropriate units. P = __ Submit μA Value Provide Feedback Request Answer Units ? Next >
The short circuit at port 2 and applying 20V at port 1 means that V₁ = 20V and V₂ = 0V.On the other hand, the open circuit at port 1 and applying 80V at port 2 means that V₂ = 80V and V₁ = 0V.
The circuit is a two-port network that is resistive and can deliver maximum power to a resistive load at port 2. The circuit is driven by a 6 A dc current source with an internal resistance of 70 Ω.The values of voltages and currents are used to find the parameters for a two-port network.
Thus the following set of equations can be obtained:$$I_1=I_{10}-V_1/R_i$$ $$I_2=I_{20}+AV_1$$Where I₁₀ and I₂₀ are the currents with no voltage and A is the current gain of the network. To obtain the value of A, the value of V₂ and I₂ when V₁ = 0 is used. So when V₁=0, then V₂=80V, and I₂ = 3A.Hence A = I₂/V₁ = 3/80 = 0.0375 Substituting the values of A and I₁ and solving the equations for V₁ and V₂, we get:$$V_1 = -1000/37$$ $$V_2 = 37000/37$$To find the value of P, we must first find the Thevenin's equivalent circuit of the given network by setting the input voltage source equal to zero.
To know more about circuit visit:-
https://brainly.com/question/33224122
#SPJ11
Equilibrium cooling of a hyper-eutectoid steel to room temperature will form: A. Pro-eutectoid ferrite and pearlite B. Pro-eutectoid ferrite and cementite C. Pro-eutectoid cementite and pearlite Pro-eutectoid cementite and austenite D.
Answer : Option C
Solution : Equilibrium cooling of a hyper-eutectoid steel to room temperature will form pro-eutectoid cementite and pearlite. Hence, the correct option is C.
A steel that contains more than 0.8% of carbon by weight is known as hyper-eutectoid steel. Carbon content in such steel is above the eutectoid point (0.8% by weight) and less than 2.11% by weight.
The pearlite is a form of iron-carbon material. The structure of pearlite is lamellar (a very thin plate-like structure) which is made up of alternating layers of ferrite and cementite. A common pearlitic structure is made up of about 88% ferrite by volume and 12% cementite by volume. It is produced by slow cooling of austenite below 727°C on cooling curve at the eutectoid point.
Iron carbide or cementite is an intermetallic compound that is formed from iron (Fe) and carbon (C), with the formula Fe3C. Cementite is a hard and brittle substance that is often found in the form of a lamellar structure with ferrite or pearlite. Cementite has a crystalline structure that is orthorhombic, with a space group of Pnma.
Know more about cooling here:
https://brainly.com/question/32239921
#SPJ11
Breeze Toothpaste Company has been having a problem with some of the tubes of toothpaste leaking. The tubes are produced in lots of 100 and are subject to 100% visual inspection. The latest 25 lots produced yielded 112 rejected toothpastes. 1) Calculate the central line and control limits to monitor this process? 2) What is the approximate probability of Type 2 error if the mean shifts to 5.2? 3) Use the Poisson Table to find the approximate probability of Type 1 error.
The probability of a Type II error can be calculated as follows:
P(Type II error) = β = P(fail to reject H0 | H1 is true)
We are given that if the true mean shifts to 5.2, then the probability distribution changes to a normal distribution with a mean of 5.2 and a standard deviation of 0.1.
To calculate the probability of a Type II error, we need to find the probability of accepting the null hypothesis (μ = 5) when the true mean is actually 5.2 (i.e., rejecting the alternative hypothesis, μ ≠ 5).P(Type II error) = P(accept H0 | μ = 5.2)P(accept H0 | μ = 5.2) = P(Z < (CL - μ) / (σ/√n)) = P(Z < (8.08 - 5.2) / (0.1/√100)) = P(Z < 28.8) = 1
In this case, we assume that the toothpastes are randomly inspected, so the number of defects in each lot follows a We want to calculate the probability of Type I error, which is the probability of rejecting a null hypothesis that is actually true (i.e., accepting the alternative hypothesis when it is false).
To know more about probability visit:
https://brainly.com/question/31828911
#SPJ11
Q6
Question 6 Other tests: a) Nominate another family of tests which may be required on a completed fabrication? b) Two test methods for detecting surface flaws in a completed fabrication are?
Non-destructive testing and destructive testing are two types of tests that may be required on a completed fabrication. Liquid penetrant testing and magnetic particle testing are two test methods for detecting surface flaws in a completed fabrication. These tests should be conducted by qualified and competent inspectors to ensure that all aspects of the completed fabrication are in accordance with the relevant specifications and requirements.
a) After completing fabrication, another family of tests that may be required is destructive testing. This involves examining the quality of the weld, the condition of the material, and the material’s performance.
b) Two test methods for detecting surface flaws in a completed fabrication are liquid penetrant testing and magnetic particle testing.Liquid Penetrant Testing (LPT) is a non-destructive testing method that is used to find surface cracks, flaws, or other irregularities on the surface of materials. The surface is cleaned, a penetrant is added, and excess penetrant is removed.
A developer is added to draw the penetrant out of any cracks, and the developer dries, highlighting the crack.Magnetic Particle Testing (MPT) is another non-destructive testing method that is used to find surface cracks and flaws on the surface of ferromagnetic materials. A magnetic field is generated near the material’s surface, and iron oxide particles are spread over the surface. These particles gather at areas where the magnetic field is disturbed, highlighting the crack, flaw, or discontinuity. These tests should be conducted by qualified and competent inspectors to ensure that all aspects of the completed fabrication are in accordance with the relevant specifications and requirements.
Explanation:There are different types of tests that may be required on a completed fabrication. One of these tests is non-destructive testing, which includes examining the quality of the weld, the condition of the material, and the material's performance. Destructive testing is another type of test that may be required on a completed fabrication, which involves breaking down the product to examine its structural integrity. Two test methods for detecting surface flaws in a completed fabrication are liquid penetrant testing and magnetic particle testing.
Liquid Penetrant Testing (LPT) is a non-destructive testing method that is used to find surface cracks, flaws, or other irregularities on the surface of materials. Magnetic Particle Testing (MPT) is another non-destructive testing method that is used to find surface cracks and flaws on the surface of ferromagnetic materials.
To know more about magnetic visit:
brainly.com/question/3617233
#SPJ11
Air is expanded in an isentropic turbine from an initial temperature of 1500 K and a pressure of 2MPa to a final pressure of 0.1MPa at a steady flow rate of 20 kg/s. Use the following properties for air to solve the questions below −γ=1.4 and c p =1001 J/kg−K
a) What is the final temperature of the air at the exit of the turbine in [K] ? Shiow yow work below or on a separate page and enter this value in the Canas guiz. b) What is the power produced by this turbine in [kW]? Show your work below or on a separate page and enter this value in the Camns quiz.
c) Draw this process on both a P-v and T-s diagram, labeling both states. Draw your diagram below do not enter arsthing into the Camas quis.
a. Final temperature of air at the exit of turbine: T2 = 858.64 K
b. Power produced by the turbine: 28,283.2 kW
c. P-v and T-s diagrams: The given process is an isentropic expansion process.
T-s diagram: State 1 is the initial state and State 2 is the final state.
Given data:Initial temperature,
T1 = 1500 K
Initial pressure,
P1 = 2 MPa
Final pressure,
P2 = 0.1 MPa
Mass flow rate, m = 20 kg/s
Ratio of specific heat, γ = 1.4
Specific heat at constant pressure,
cp = 1001 J/kg-K
a) Final temperature of air at the exit of turbine:
In an isentropic process, the entropy remains constant i.e
ds = 0.
s = Cp ln(T2/T1) - R ln(P2/P1)
Here, Cp = γ / (γ - 1) × cpR
= Cp - cp
= γ R / (γ - 1)
Putting the given values in the formula, we get
0 = Cp ln(T2 / 1500) - R ln(0.1 / 2)
T2 = 858.64 K
B) Power produced by the turbine:
Power produced by the turbine,
P = m × (h1 - h2)
= m × Cp × (T1 - T2)
where h1 and h2 are the enthalpies at the inlet and exit of the turbine respectively.
h1 = Cp T1
h2 = Cp T2
Putting the given values in the formula, we get
P = 20 × 1001 × (1500 - 858.64)
P = 28,283,200 W
= 28,283.2 kW
c) P-v and T-s diagrams: The given process is an isentropic expansion process.
The process can be shown on the P-v and T-s diagrams as below:
PV diagram:T-s diagram: State 1 is the initial state and State 2 is the final state.
To know more about T-s diagrams visit:
https://brainly.com/question/13327155
#SPJ11
For two given fuzzy sets,
Please calculate the composition operation of R and S. For two given fuzzy sets, R = = [0.2 0.8 0:2 0:1].s = [0.5 0.7 0.1 0 ] Please calculate the composition operation of R and S. (7.0)
The composition operation of two fuzzy relations R and S is given by[tex]R∘S(x,z) = supy(R(x,y) ∧ S(y,z)).[/tex]
To calculate the composition operation of R and S we have the given fuzzy sets R and
S.R
=[tex][0.2 0.8 0.2 0.1]S = [0.5 0.7 0.1 0][/tex]
[tex]R ∘ S(1,1):R(1, y)∧ S(y,1) = [0, 0.7, 0.1, 0][0.2, 0.8, 0.2, 0.1]≤ [0, 0.7, 0.2, 0.1][/tex]
Thus, sup of this subset is 0.7
[tex]R ∘ S(1,1) = 0.7[/tex]
we can find the compositions of R and S as given below:
[tex]R ∘ S(1,2) = 0.8R ∘ S(1,3) = 0.2R ∘ S(1,4) = 0R ∘ S(2,1) = 0.5R ∘ S(2,2) = 0.7R ∘ S(2,3) = 0.1R ∘ S(2,4) = 0R ∘ S(3,1) = 0.2R ∘ S(3,2) = 0.56R ∘ S(3,3) = 0.1R ∘ S(3,4) = 0R ∘ S(4,1) = 0.1R ∘ S(4,2) = 0.28R ∘ S(4,3) = 0R ∘ S(4,4) = 0[/tex]
Thus, the composition operation of R and S is given by:
[tex]R ∘ S = [0.7 0.8 0.2 0; 0.5 0.7 0.1 0; 0.2 0.56 0.1 0; 0.1 0.28 0 0][/tex]
the composition operation of R and S is
[tex][0.7 0.8 0.2 0; 0.5 0.7 0.1 0; 0.2 0.56 0.1 0; 0.1 0.28 0 0].[/tex]
To know more about fuzzy visit:-
https://brainly.com/question/31475345
#SPJ11
knowing that each of the shaft AB, BC, and CD consist
of a solid circular rod, determine the shearing stress in shaft AB,
BD and CD. (final answer in mpa, 3 decimal places)
Given:Shaft AB: diameter = 80 mm, torque = 16 kNmShaft BC: diameter = 60 mm, torque = 24 kNmShaft CD: diameter = 40 mm, torque = 30 kNmSolution:The polar moment of inertia, J = (π/32)d⁴Shaft AB: diameter (d) = 80 mmTorque (T) = 16 kNmSince [tex]τ = (T/J) x r τ = (16 x 10⁶) / [(π/32) x (80)⁴ / 64] x (40)τ = 51.64[/tex] MPa
Therefore, the shearing stress in shaft AB is 51.64 MPa.Shaft BD: diameter (d) = 60 mm and 40 mmTorque (T) = 24 kNm and 30 kNmNow, the distance from the center to shaft AB is equal to the sum of the radius of shaft BC and CD.
So, [tex]r = 20 + 30 = 50 mmτ = (T/J) x r[/tex] for the two shafts
BD:[tex]τ = (24 x 10⁶) / [(π/32) x (60)⁴ / 64] x (50)τ = 70.38[/tex] MPa
CD:[tex]τ = (30 x 10⁶) / [(π/32) x (40)⁴ / 64] x (50)τ = 150.99[/tex] MPa
Therefore, the shearing stress in shaft BD and CD is 70.38 MPa and 150.99 MPa, respectively.The shearing stress in shaft AB, BD, and CD is 51.64 MPa, 70.38 MPa and 150.99 MPa, respectively.
To know more about radius visit:
https://brainly.com/question/13449316
#SPJ11
The resistivity of an Al sample is found to be 2μ0.cm. Calculate the mobility of electrons in Al. Let e=1.6x10⁻¹⁹ C and nAl=1.8 x 10²³ cm⁻³
The mobility of electrons in Al is found to be 1.74 × 10⁻³ cm² V⁻¹ s⁻¹.
Given:
Resistivity of aluminum (Al), ρ = 2 μΩ.cm,
Charge of electron, e = 1.6 × 10⁻¹⁹ C,
Number density of Al,
nAl = 1.8 × 10²³ cm⁻³
Mobility is defined as the ratio of the drift velocity of the charge carrier to the applied electric field.
Mathematically,
mobility = drift velocity / electric field
and drift velocity,
vd = μE
where vd is the drift velocity,
E is the applied electric field and
μ is the mobility of the charge carrier.
So, we can also write,
mobility, μ = vd / E
Let's use the formula of resistivity for aluminum to find the expression for electric field, E.
resistivity, ρ = 1 / σ
where σ is the conductivity of aluminum.
Therefore, conductivity,
σ = 1 / ρ
⇒ σ = 1 / (2 × 10⁻⁶ Ω⁻¹.cm⁻¹)
⇒ σ = 5 × 10⁵ Ω⁻¹.cm⁻¹
Now, the current density,
J = σE,
where
J = nevd is the current density due to electron drift,
n is the number density of electrons in the material,
e is the charge of an electron and vd is the drift velocity.
So, using the formula,
σE = nevd
⇒ E = nevd / σ
And, mobility,
μ = vd / E
⇒ μ = (J / ne) / (E / ne)
⇒ μ = J / E
Here,
J = nevd
= neμE.
So, we can also write,
μ = nevd / neE
⇒ μ = vd / Ew
here vd = μE is the drift velocity of the charge carrier.
Substituting the given values, we get
μ = (nAl e vd) / (nAl e E)
⇒ μ = vd / E = (σ / ne)
= (5 × 10⁵ Ω⁻¹.cm⁻¹) / (1.8 × 10²³ cm⁻³ × 1.6 × 10⁻¹⁹ C)
⇒ μ = 1.74 × 10⁻³ cm² V⁻¹ s⁻¹
Know more about the mobility of electrons
https://brainly.com/question/32257278
#SPJ11
Design a synchronously settable flip-flop using a regular D flip-flop and additional gates. The inputs are Clk, D, and Set, and the output is Q. Sketch your design.
A flip-flop is a digital device that stores a binary state. The term "flip-flop" refers to the ability of the device to switch between two states. A D flip-flop is a type of flip-flop that can store a single bit of information, known as a "data bit." A D flip-flop is a synchronous device, which means that its output changes only on the rising or falling edge of the clock signal.
In this design, we will be using a D flip-flop and some additional gates to create a synchronously settable flip-flop. We will be using an AND gate, an inverter, and a NOR gate.
To design the synchronously settable flip-flop using a regular D flip-flop and additional gates, follow these steps:
1. Start by drawing a regular D flip-flop, which has two inputs, D and Clk, and one output, Q.
2. Draw an AND gate with two inputs, Set and Clk. The output of the AND gate will be connected to the D input of the D flip-flop.
3. Draw an inverter, and connect its input to the output of the AND gate. The output of the inverter will be connected to one input of a NOR gate.
4. Connect the Q output of the D flip-flop to the other input of the NOR gate.
5. The output of the NOR gate will be the output of the synchronously settable flip-flop, Q.
6. Sketch the complete design as shown in the figure below.Sketch of the design:In this design, when the Set input is high and the Clk input is high, the output of the AND gate will be high. This will set the D input of the D flip-flop to high, regardless of the value of the current Q output of the flip-flop.
To know more about synchronous visit:
https://brainly.com/question/27189278
#SPJ11
Water with a velocity of 3.38 m/s flows through a 148 mm
diameter pipe. Solve for the weight flow rate in N/s. Express your
answer in 2 decimal places.
Given that water with a velocity of 3.38 m/s flows through a 148 mm diameter pipe. To determine the weight flow rate in N/s, we need to use the formula for volumetric flow rate.
Volumetric flow rate Q = A x V
where, Q = volumetric flow rate [m³/s]
A = cross-sectional area of pipe [m²]
V = velocity of fluid [m/s]Cross-sectional area of pipe
A = π/4 * d²A = π/4 * (148mm)²A = π/4 * (0.148m)²A = 0.01718 m²
Substituting the given values in the formula we get Volumetric flow rate
Q = A x V= 0.01718 m² × 3.38 m/s= 0.058 s m³/s
To determine the weight flow rate, we can use the formula Weight flow
rate = volumetric flow rate × density Weight flow rate = Q × ρ\
To know more about diameter visit:
https://brainly.com/question/32968193
#SPJ11
13. Give the definition of entropy. Why did we create this quantity? 14. What is the relationship between entropy, heat, and reversibility?
Entropy is a physical quantity that measures the level of disorder or randomness in a system. It is also known as the measure of the degree of disorder in a system.
Entropy has several forms, but the most common is thermodynamic entropy, which is a measure of the heat energy that can no longer be used to do work in a system. The entropy of an isolated system can never decrease, and this is known as the Second Law of Thermodynamics. The creation of entropy was necessary to explain how heat energy moves in a system.
Relationship between entropy, heat, and reversibility Entropy is related to heat in the sense that an increase in heat will increase the entropy of a system. Similarly, a decrease in heat will decrease the entropy of a system.
To know more about Entropy visit-
https://brainly.com/question/20166134
#SPJ11
A balanced 3 phase star connected load draws power from a 430 V supply. Two wattmeter's indicate 9600 W and 3700 W respectively, when connected to measure the input power of the load, the reverse switch being operated on the meter indicating the 3700 W reading. [2.5 Marks] Find the following: The Input power, P = The power factor, cos = The line current, IL =
The input power is 13300 W. The power factor is approximately 0.4436. The line current is approximately 18.39 A.
To find the input power, power factor, and line current, we can use the readings from the two wattmeters.
Let's denote the reading of the first wattmeter as [tex]$P_1$[/tex] and the reading of the second wattmeter as [tex]$P_2$[/tex]. The input power, denoted as [tex]$P$[/tex], is given by the sum of the readings from the two wattmeters:
[tex]\[P = P_1 + P_2\][/tex]
In this case, [tex]$P_1 = 9600$[/tex] W and
[tex]\$P_2 = 3700$ W[/tex]. Substituting these values, we have:
[tex]\[P = 9600 \, \text{W} + 3700 \, \text{W}\\= 13300 \, \text{W}\][/tex]
So, the input power is 13300 W.
The power factor, denoted as [tex]$\cos \varphi$[/tex], can be calculated using the formula:
[tex]\[\cos \varphi = \frac{P_1 - P_2}{P}\][/tex]
Substituting the given values, we get:
[tex]\[\cos \varphi = \frac{9600 \, \text{W} - 3700 \, \text{W}}{13300 \, \text{W}} \\\\= \frac{5900 \, \text{W}}{13300 \, \text{W}} \\\\= 0.4436\][/tex]
So, the power factor is approximately 0.4436.
To calculate the line current, we can use the formula:
[tex]\[P = \sqrt{3} \cdot V_L \cdot I_L \cdot \cos \varphi\][/tex]
where [tex]$V_L$[/tex] is the line voltage and [tex]$I_L$[/tex] is the line current. Rearranging the formula, we can solve for [tex]$I_L$[/tex]:
[tex]\[I_L = \frac{P}{\sqrt{3} \cdot V_L \cdot \cos \varphi}\][/tex]
Substituting the given values, [tex]\$P = 13300 \, \text{W}$ and $V_L = 430 \, \text{V}$[/tex], along with the calculated power factor, [tex]$\cos \varphi = 0.4436$[/tex], we have:
[tex]\[I_L = \frac{13300 \, \text{W}}{\sqrt{3} \cdot 430 \, \text{V} \cdot 0.4436} \approx 18.39 \, \text{A}\][/tex]
So, the line current is approximately 18.39 A.
Know more about power factor:
https://brainly.com/question/31782928
#SPJ4
What are the reasons behind occurance of Escape peak, Internal Fluorocence peak,Sum peak, Spurious peak, Coherent Breamstrahlung peak in EDX spectrum? How to confirm a set of peaks as Coherent Breamstrahlung peaks? Why Be window is used generally with Si(Li) detector in EDXS? While cooling is needed for Si(Li) detector (10+1+2+2)
Escape peaks, internal fluorescence peaks, sum peaks, spurious peaks, and coherent bremsstrahlung peaks can occur in an Energy Dispersive X-ray Spectroscopy (EDX) spectrum.
Escape peaks result from X-rays escaping the detector and undergoing secondary interactions, producing lower-energy peaks. Internal fluorescence peaks occur when the sample emits characteristic X-rays that are reabsorbed and re-emitted within the sample, resulting in additional peaks. Sum peaks arise from the simultaneous detection of two X-rays, leading to a peak at the combined energy. Spurious peaks can emerge due to instrumental artifacts or sample impurities. Coherent bremsstrahlung peaks are produced when high-energy electrons interact with the sample, generating a broad background of X-rays. These peaks can be confirmed by analyzing the spectrum for the presence of a continuous background that increases with energy.
Learn more about X-rays here:
https://brainly.com/question/8611796
#SPJ11
Mr P wishes to develop a single reduction gearbox with 20° full depth spur gears that will transfer 3 kW at 2 500 rpm. There are 20 teeth on the pinion and 50 teeth on the gear. Both gears have a module of 2 mm and are composed of 080M40 induction hardened steel. 2.1 Write a problem statement for Mr P's design. (1) 2.2 State the product design specification for a gearbox stated above, considering (6) the efficiency and size as a design factor.
2.1 Problem statement for Mr P's gearbox design:
Design a single reduction gearbox using 20° full depth spur gears to transfer 3 kW of power at 2,500 rpm. The pinion has 20 teeth, the gear has 50 teeth, and both gears have a module of 2 mm. The gears are made of 080M40 induction hardened steel. Ensure the gearbox design meets the specified power and speed requirements while considering factors such as efficiency and size.
2.2 Product design specification for the gearbox:
1. Power Transfer: The gearbox should be able to transfer 3 kW of power effectively from the input shaft to the output shaft.
2. Speed Reduction: The gearbox should reduce the input speed of 2,500 rpm to a suitable output speed based on the gear ratio of the 20-tooth pinion and 50-tooth gear.
3. Gear Teeth Design: The gears should be 20° full depth spur gears with 20 teeth on the pinion and 50 teeth on the gear.
4. Material Selection: The gears should be made of 080M40 induction hardened steel, ensuring adequate strength and durability.
5. Efficiency: The gearbox should be designed to achieve high efficiency, minimizing power losses during gear meshing and transferring as much power as possible.
6. Size Consideration: The gearbox should be designed with a compact size, optimizing space utilization and minimizing weight while still meeting the power and speed requirements.
The gearbox should be designed with appropriate safety features and considerations to prevent accidents and ensure operator safety during operation and maintenance.
To learn more about Gearbox, click here:
https://brainly.com/question/32201987
#SPJ11
Vector A is represented by 3i - 7j + 2k, while vector B lies in the x/y plane, and has a magnitude of 8 and a (standard) angle of 120⁰. (a) What is the magnitude of A? (2 pt) (b) What is 3A - 2B? (2 pt) (c) What is A x B? (3 pt) (d) What is the angle between A and B?
In conclusion the magnitude of vector A is approximately
[tex]7.874b) 3A - 2B = 25i - 34.856j + 6kc) A x B = -13.856i - 6j - 6.928kd)[/tex] The angle between A and B is approximately 86.8° (to one decimal place).
Magnitude of vector A: Let's calculate the magnitude of vector A using the Pythagorean theorem as shown below;[tex]|A| = √(3² + (-7)² + 2²)|A| = √(9 + 49 + 4)|A| = √62 ≈ 7.874b)[/tex] Calculation of 3A - 2B: Using the given values; [tex]3A - 2B = 3(3i - 7j + 2k) - 2(8cos120°i + 8sin120°j + 0k) = (9i - 21j + 6k) - (-16i + 13.856j + 0k) = 25i - 34.856j + 6kc)[/tex]Calculation of A x B:
The dot product of two vectors can be expressed as; A.B = |A||B|cosθ Let's find A.B from the two vectors;[tex]A.B = (3)(8cos120°) + (-7)(8sin120°) + (2)(0)A.B = 1.195[/tex] ;[tex]1.195 = 7.874(8)cosθcosθ = 1.195/62.992cosθ = 0.01891θ = cos-1(0.01891)θ = 86.8°[/tex] The angle between A and B is 86.8° (to one decimal place).
To know more about vector visit:
https://brainly.com/question/29740341
#SPJ11
For the same velocity field described in question 15. generate an expression for the stream function and plot some streamlines of the flow in the upper-right quadrant (0, 0) and (2, 2) in the interval of=2 m²/s. Clearly state the assumptions and boundary conditions.
The stream function ψ(x,y) represents the streamlines, or pathlines, of a fluid in a two-dimensional flow field. Streamlines are curves that are tangent to the velocity vectors in the flow.
The velocity field is two-dimensional. The velocity field is incompressible. Boundary conditions: The velocity of the fluid is zero at the walls of the channel.
The velocity of the fluid is zero at infinity. To find the stream function ψ(x,y), we must solve the equation of continuity for two-dimensional flow in terms of ψ(x,y).
Continuity equation is:∂u/∂x+∂v/∂y=0,where u and v are the x and y components of velocity respectively, and x and y are the coordinates of a point in the fluid.
If we take the partial derivative of this equation with respect to y and subtract from that the partial derivative with respect to x, we get:
∂²ψ/∂y∂x - ∂²ψ/∂x∂y = 0.
Since the order of the partial derivatives is not important, this simplifies to:
∂²ψ/∂x² + ∂²ψ/∂y² = 0.
The above equation is known as the two-dimensional Laplace equation and is subject to the same boundary conditions as the velocity field. We can solve the Laplace equation using separation of variables and assuming that ψ(x,y) is separable, i.e.
ψ(x,y) = X(x)Y(y).
After solving the equation for X(x) and Y(y), we can find the stream function ψ(x,y) by multiplying X(x)Y(y).
The stream function can then be used to find the streamlines by plotting the equation
ψ(x,y) = constant, where constant is a constant value. The streamlines will be perpendicular to the contours of constant ψ(x,y).Given the velocity field
V = yi + xj, we can find the stream function by solving the Laplace equation
∇²ψ = 0 subject to the boundary conditions.
We can assume that the fluid is incompressible and the flow is two-dimensional. The velocity of the fluid is zero at the walls of the channel and at infinity.
We can find the stream function by solving the Laplace equation using separation of variables and assuming that ψ(x,y) is separable, i.e.
ψ(x,y) = X(x)Y(y).
After solving the equation for X(x) and Y(y), we can find the stream function ψ(x,y) by multiplying X(x)Y(y).
The stream function can then be used to find the streamlines by plotting the equation ψ(x,y) = constant, where constant is a constant value.
The streamlines will be perpendicular to the contours of constant ψ(x,y).
To find the stream function, we assume that
ψ(x,y) = X(x)Y(y).
We can write the Laplace equation in terms of X(x) and Y(y) as:
X''/X + Y''/Y = 0.
We can rewrite this equation as:
X''/X = -Y''/Y = -k²,where k is a constant.
Solving for X(x), we get:
X(x) = A sin(kx) + B cos(kx).
Solving for Y(y), we get:
Y(y) = C sinh(ky) + D cosh(ky).
Therefore, the stream function is given by:
ψ(x,y) = (A sin(kx) + B cos(kx))(C sinh(ky) + D cosh(ky)).
To satisfy the boundary condition that the velocity of the fluid is zero at the walls of the channel, we must set A = 0. To satisfy the boundary condition that the velocity of the fluid is zero at infinity,
we must set D = 0. Therefore, the stream function is given by:
ψ(x,y) = B sinh(ky) cos(kx).
To find the streamlines, we can plot the equation ψ(x,y) = constant, where constant is a constant value. In the upper-right quadrant, the boundary conditions are x = 0, y = 2 and x = 2, y = 0.
Therefore, we can find the value of B using these boundary conditions. If we set
ψ(0,2) = 2Bsinh(2k) = F and ψ(2,0) = 2Bsinh(2k) = G, we get:
B = F/(2sinh(2k)) = G/(2sinh(2k)).
Therefore, the stream function is given by:ψ(x,y) = Fsinh(2ky)/sinh(2k) cos(kx) = Gsinh(2kx)/sinh(2k) cos(ky).We can plot the streamlines by plotting the equation ψ(x,y) = constant.
The streamlines will be perpendicular to the contours of constant ψ(x,y).
To learn more about Laplace equation
https://brainly.com/question/31583797
#SPJ11
Show that the circulation around an infinitesimally small rectangular path of dimensions 8x and Sy in Cartesian coordinates is directly related to the local vorticity multiplied by the area enclosed by the path
The circulation around an infinitesimally small rectangular path of dimensions 8x and Sy in Cartesian coordinates is directly related to the local vorticity multiplied by the area enclosed by the path.
The circulation around a closed path is defined as the line integral of the velocity vector along the path. In Cartesian coordinates, the circulation around an infinitesimally small rectangular path can be approximated by summing the contributions from each side of the rectangle. Consider a rectangular path with dimensions 8x and Sy. Each side of the rectangle can be represented by a line segment. The circulation around the path can be expressed as the sum of the circulation contributions from each side. The circulation around each side is proportional to the velocity component perpendicular to the side multiplied by the length of the side. Since the rectangle is infinitesimally small.
Learn more about infinitesimally small rectangular path here:
https://brainly.com/question/14529499
#SPJ11
Since Auger effect produce electron with chemically specific energy for each elements, Auger electron spectroscopy is a very useful thin film analysis technique for modern day materials science. Can hydrogen or helium be detected by this way? Explain.
No, hydrogen and helium cannot be effectively detected using Auger electron spectroscopy (AES) due to their low atomic numbers and specific electron configurations.
Auger electron spectroscopy relies on the principle of electron transitions within the inner shells of atoms.
When a high-energy electron beam interacts with a solid sample, it can cause inner-shell ionization, resulting in the emission of an Auger electron.
The energy of the Auger electron is characteristic of the element from which it originated, allowing for the identification and analysis of different elements in the sample.
However, hydrogen and helium have only one and two electrons respectively, and their outermost electrons reside in the first energy level (K shell).
Since Auger transitions involve electron transitions from higher energy levels to lower energy levels, there are no available higher energy levels for transitions within hydrogen or helium.
As a result, Auger electron emission is not observed for these elements.
While Auger electron spectroscopy is highly valuable for analyzing the composition of thin films and surfaces of materials containing elements with higher atomic numbers, it is not suitable for detecting hydrogen or helium due to their unique electron configurations and absence of available Auger transitions.
Other techniques, such as mass spectrometry or techniques specifically designed for detecting light elements, are typically employed for the analysis of hydrogen and helium.
to learn more about Auger electron spectroscopy.
https://brainly.com/question/29363677
Given below is a system of two non-linear algebraic equations: f(x, y) = 0
g(x,y)=0 where, f(x,y) = y² + ex g(x, y) = cos(y)-y
If the solution after the 3rd iteration is: x(3)= 1.5 and y(3) = 2, find the normal of the residual (||R||) for this 3rd iteration. Show your steps.
Given the system of equations:[tex]f(x, y) = 0 and g(x, y) = 0,[/tex]
where [tex]f(x, y) = y² + ex[/tex] and
[tex]g(x, y) = cos(y) - y[/tex]. The Newton-Raphson method for solving nonlinear equations is given by the following iterative formula:
[tex]x(n+1) = x(n) - [f(x(n), y(n)) / f'x(x(n), y(n))][/tex]
[tex]y(n+1) = y(n) - [g(x(n), y(n)) / g'y(x(n), y(n))][/tex]
The partial derivatives of f(x, y) and g(x, y) are as follows:
[tex]∂f/∂x = 0, ∂f/∂y = 2y[/tex]
[tex]∂g/∂x = 0, ∂g/∂y = -sin(y)[/tex]
Applying these derivatives, the iterative formula for solving the system of equations becomes:
[tex]x(n+1) = x(n) - (ex + y²) / e[/tex]
[tex]y(n+1) = y(n) - (cos(y(n)) - y(n)) / (-sin(y(n)))[/tex]
To calculate x(3) and y(3), given [tex]x(0) = 0 and y(0) = 1:[/tex]
[tex]x(1) = 0 - (e×1²) / e = -1[/tex]
[tex]y(1) = 1 - [cos(1) - 1] / [-sin(1)] ≈ 1.38177329068[/tex]
[tex]x(2) = -1 - (e×1.38177329068²) / e ≈ -3.6254167073[/tex]
y(2) =[tex]1.38177329068 - [cos(1.38177329068) - 1.38177329068] / [-sin(1.38177329068)] ≈ 2.0706220035[/tex]
x(3) =[tex]-3.6254167073 - [e×2.0706220035²] / e ≈ -7.0177039346[/tex]
y(3) = [tex]2.0706220035 - [cos(2.0706220035) - 2.0706220035] / [-sin(2.0706220035)] ≈ 1.8046187686[/tex]
The matrix equation for the residual (||R||) is given by:
||R|| = [(f(x(n), y(n))² + g(x(n), y(n))²)]^0.5
Calculating ||R|| for the 3rd iteration:
f[tex](-7.0177039346, 1.8046187686) = (1.8046187686)² + e(-7.0177039346) ≈ 68.3994096346[/tex]
g[tex](-7.0177039346, 1.8046187686) = cos(1.8046187686) - (1.8046187686) ≈ -1.2429320348[/tex]
[tex]||R|| = [(f(-7.0177039346, 1.8046187686))² + (g(-7.0177039346, 1.8046187686))²]^0.5[/tex]
[tex]= [68.3994096346² + (-1.2429320348)²]^0.5[/tex]
[tex]≈ 68.441956[/tex]
Therefore, the norm of the residual (||R||) for the 3rd iteration is approximately 68.441956.
To know more about derivatives visit:
https://brainly.com/question/25324584
#SPJ11
hile was olo- cent esti- the 15-88-Octane [CgH₁g()] is burned in an automobile engine with 200 percent excess air. Air enters this engine at 1 atm and 25°C. Liquid fuel at 25°C is mixed with this air before combustion. The exhaust products leave the exhaust system at I atm and 77°C. What is the maximum amount of work, in kJ/ kg fuel, that can be produced by this engine? Take To= 25°C. Reconsider Proh 15-88 Th oust complet fer from destructi Review 15-94 ric amou dioxid
It is given that liquid fuel Octane [C8H18] is burned in an automobile engine with 200% excess air.The fuel and air mixture enter the engine at 1 atm and 25°C and the exhaust leaves at 1 atm and 77°C.
Temperature of surroundings = 25°CProblems:We have to determine the maximum amount of work, in kJ/kg fuel, that can be produced by the engine.Calculation:Given fuel is Octane [C8H18].So, we have molecular weight,
M = 8(12.01) + 18(1.008)
= 114.23 gm/molR
= 8.314 J/ mol KAir is entering at 25°C.
So,
T1 = 25°C + 273.15
= 298.15 Kand P1
= 1 atm
= 1.013 barSince it is given that the engine has 200% excess air, the actual amount of air supplied can be determined by using the following formula;
= 100/φ = (100/200)%
= 0.5 or 1/2 times the stoichiometric amount of air.
To know more about liquid fuel visit:
https://brainly.com/question/30455402
#SPJ11
2) A linear elastic SDOF system is given below with Tn= 1.1 s, m = 1 kg, 5 = 5 %, u(0) = 0, u(0) = 0. Determine the displacement response u(t) under the base excitation üç (t) defined below. Use At = 0.1 s in calculations. 0.6 U m i A oli 0,2 013 014 015 kc -0.4 Time (s)
Given values:Tn = 1.1 s, m = 1 kg, ξ = 5%, u(0) = 0, u'(0) = 0.At = 0.1 s
And base excitation üc(t) is given as below:
0.6 Umi sin (2πti) for 0 ≤ t ≤ 0.2 s0.2 sin (2π(501)(t - 0.2)) for 0.2 ≤ t ≤ 0.3 s-0.4 sin (2π(501)(t - 0.3)) for 0.3 ≤ t ≤ 0.4 sThe undamped natural frequency can be calculated as
ωn = 2π / Tnωn = 2π / 1.1ωn = 5.7 rad/s
The damped natural frequency can be calculated as
ωd = ωn √(1 - ξ²)ωd = 5.7 √(1 - 0.05²)ωd = 5.41 rad/s
The damping coefficient can be calculated as
k = m ξ ωnk = 1 × 0.05 × 5.7k = 0.285 Ns/m
The spring stiffness can be calculated as
k = mωd² - ξ²k = 1 × 5.41² - 0.05²k = 14.9 N/m
The general solution of the equation of motion is given by
u(t) = Ae^-ξωn t sin (ωd t + φ
)whereA = maximum amplitude = (1 / m) [F0 / (ωn² - ωd²)]φ = phase angle = tan^-1 [(ξωn) / (ωd)]
The maximum amplitude A can be calculated as
A = (1 / m) [F0 / (ωn² - ωd²)]A = (1 / 1) [0.6 Um / ((5.7)² - (5.41)²)]A = 0.2219
UmThe phase angle φ can be calculated astanφ = (ξωn) / (ωd)tanφ = (0.05 × 5.7) / (5.41)tanφ = 0.0587φ = 3.3°
Displacement response u(t) can be calculated as:for 0 ≤ t ≤ 0.2 s, the displacement response u(t) isu(t) = 0.2219 Um e^(-0.05 × 5.7t) sin (5.41t + 3.3°)for 0.2 ≤ t ≤ 0.3 s, the displacement response
u(t) isu(t) = 0.2219 Um e^(-0.05 × 5.7t) sin (5.41t - 30.35°)for 0.3 ≤ t ≤ 0.4 s, t
he displacement response
u(t) isu(t) = 0.2219 Um e^(-0.05 × 5.7t) sin (5.41t + 57.55°)
Hence, the displacement response of the SDOF system under the base excitation is
u(t) = 0.2219 Um e^(-0.05 × 5.7t) sin (5.41t + φ) for 0 ≤ t ≤ 0.2 s, 0.2 ≤ t ≤ 0.3 s, and 0.3 ≤ t ≤ 0.4 s, whereφ = 3.3° for 0 ≤ t ≤ 0.2 su(t) = 0.2219 Um e^(-0.05 × 5.7t) sin (5.41t - 30.35°) for 0.2 ≤ t ≤ 0.3 su(t) = 0.2219 Um e^(-0.05 × 5.7t) sin (5.41t + 57.55°) for 0.3 ≤ t ≤ 0.4 s. The response is plotted below.
To know more about frequency visit :
https://brainly.com/question/29739263
#SPJ11
2. The data of fighter during combat: Wing loading W/S = 3500 N/m², Cla = 4.8, H = 8000m (p = 0.5252 Kg/m³), V = 256m/s. The longitudinal characteristic equation is: 0.422s⁴+0.803s³+1.454s²+0.091s +0.02 = 0 (1) Using the Routh's criterion to evaluate the longitudinal dynamic stability; (2) Determine the short-period damping ration (sp and frequency Wsp. (3) Evaluate the flying quality. (20 marks)
Using Routh's criterion, the longitudinal dynamic stability of the fighter aircraft can be evaluated.
The given characteristic equation is 0.422s⁴+0.803s³+1.454s²+0.091s +0.02 = 0. Applying Routh's criterion, we construct the Routh array:
1 | 0.422 1.454
0.803 0.091
0.499 0.02
From the first row of the array, we can determine that all the coefficients are positive, indicating that there are no sign changes. Therefore, all the roots lie in the left-half plane, confirming the longitudinal dynamic stability of the aircraft. To determine the short-period damping ratio (sp) and frequency (Wsp), we need to solve the characteristic equation. The roots of the given equation can be found using numerical methods or software. Once the roots are obtained, we can calculate the damping ratio and frequency. The short-period damping ratio indicates the level of stability, and the frequency represents the oscillation rate. The flying quality of the aircraft can be evaluated based on various factors such as stability, maneuverability, controllability, and pilot workload. The longitudinal dynamic stability, as determined by Routh's criterion, indicates a stable response of the aircraft. However, a comprehensive evaluation of flying quality requires considering other factors like the aircraft's response to control inputs, its ability to perform maneuvers effectively, and the workload imposed on the pilot.
Learn more about Routh's criterion here:
https://brainly.com/question/33183933
#SPJ11
Consider Stokes' first problem, but allow the plate velocity to be an arbitrary function of time, U(t). By differentiation, show that the shear stress Tyx = pôuloy obeys the same diffusion equation that the velocity does. Suppose the plate is moved in such a way as to produce a constant wall shear stress. Determine the plate velocity for this motion. Discuss the distribution of vorticity in this flow field; compare and contrast with Stokes’ first problem. Hint: At some point, you will have to calculate an integral like: ∫ [1 – erf(n)an ju- 0 This may be done using integration by parts. It may be helpful to note that eftc(n) – n*-1exp(-n2) for large n.
Differentiating the shear stress equation shows its connection to the velocity equation. Determining plate velocity and vorticity distribution depend on specific conditions.
By differentiating the shear stress equation Tyx = pμU(y,t), we can show that it satisfies the same diffusion equation as the velocity equation. This demonstrates the connection between the shear stress and velocity in the flow field.
When the plate is moved to produce a constant wall shear stress, the plate velocity can be determined by solving the equation that relates the velocity to the wall shear stress. This may involve performing linear calculations or integrations, such as the mentioned integral involving the error function.
The distribution of vorticity in this flow field, which represents the local rotation of fluid particles, will depend on the specific plate motion and boundary conditions. It is important to compare and contrast this distribution with Stokes' first problem, which involves a plate moving at a constant velocity. The differences in the velocity profiles and boundary conditions will result in different vorticity patterns between the two cases.
Learn more about Linear click here :brainly.com/question/30763902
#SPJ11