Answer:
1/4 of its original value
Explanation:
Newton's law of universal gravitation states that when two bodies of masses M₁ and M₂ interact, the force of attraction (F) between these bodies is directly proportional to the product of their masses and inversely proportional to the square of the distance (r) between these bodies. i.e
F ∝ [tex]\frac{M_1 M_2}{r^2}[/tex] ------------(i)
From the equation above, it can be deduced that;
F ∝ [tex]\frac{1}{r^2}[/tex]
=> F = G [tex]\frac{1}{r^2}[/tex] -----------(ii)
Where;
G = constant of proportionality called the gravitational constant
Equation (ii) can be re-written as
Fr² = G
=> F₁r₁² = F₂r₂² -----------(iii)
Where;
F₁ and r₁ are the initial values of the force and distance respectively
F₂ and r₂ are the final values of the force and distance respectively
From the question, if the distance doubles i.e;
r₂ = 2r₁,
Then the final value of the gravitational force F₂ is calculated as follows;
Substitute the value of r₂ = 2r₁ into equation (iii) as follows;
F₁r₁² = F₂(2r₁)²
F₁r₁² = 4F₂r₁² [Divide through by r₁²]
F₁ = 4F₂ [Make F₂ subject of the formula]
F₂ = F₁ / 4 [Re-write this]
F₂ = [tex]\frac{1}{4} F_1[/tex]
Therefore the gravitational force will be 1/4 of its original value when the distance between the bodies doubles.
If, the limits of the visible spectrum are approximately 3000 A.U. and 5000 A.U. respectively. Determine the angular breadth of the first order visible spectrum produced by a plane diffraction grating having 12000 lines per inch when light is incident normally on the grating.
Answer:
θ₁ = 0.04º , θ₂ = 0.00118º
Explanation:
The equation that describes the diffraction pattern of a network is
d sin θ = m λ
where the diffraction order is, in this case they indicate that the order
m = 1
θ = sin⁻¹ (λ / d)
Trfuvsmod ls inrsd fr ll red s SI units
d = 12000 line / inc (1 inc / 2.54cm) = 4724 line / cm
the distance between two lines we can look for it with a direct proportions rule
If there are 4724 lines in a centimeter, the distance for two hundred is
d = 2 lines (1 cm / 4724 line) = 4.2337 10⁻⁴ cm
let's calculate the angles
λ = 300 10-9 m
θ₁ = sin⁻¹ (300 10-9 / 4,2337 10-4)
θ₁ = sin⁻¹ (7.08 10-4)
θ₁ = 0.04º
λ = 5000
θ₂ = sin-1 (500 10-9 / 4,2337 10-4)
θ₂ = 0.00118º
A uniform crate C with mass mC is being transported to the left by a forklift with a constant speed v1. What is the magnitude of the angular momentum of the crate about point A, that is, the point of contact between the front tire of the forklift and the ground
Answer:
The angular momentum of the crate is [tex]M_{C} V_{1} d[/tex]
Explanation:
mass of the crate = [tex]M_{C}[/tex]
speed of forklift = [tex]V_{1}[/tex]
The distance between the center of the mass and the point A = d
Recall that the angular moment is the moment of the momentum.
[tex]L = P*d[/tex] ..... equ 1
where L is the angular momentum,
P is the momentum of the system,
d is the perpendicular distance between the crate and the point on the axis about which the momentum acts. It is equal to d from the image
Also, we know that the momentum P is the product of mass and velocity
P = mv ....equ 2
in this case, the mass = [tex]M_{C}[/tex]
the velocity = [tex]V_{1}[/tex]
therefore, the momentum P = [tex]M_{C}[/tex][tex]V_{1}[/tex]
we substitute equation 2 into equation 1 to give
[tex]L = M_{C} V_{1} d[/tex]
Alternating Current In Europe, the voltage of the alternating current coming through an electrical outlet can be modeled by the function V 230 sin (100t), where tis measured in seconds and Vin volts.What is the frequency of the voltage
Answer:
[tex]\frac{50}{\pi }[/tex]Hz
Explanation:
In alternating current (AC) circuits, voltage (V) oscillates in a sine wave pattern and has a general equation as a function of time (t) as follows;
V(t) = V sin (ωt + Ф) -----------------(i)
Where;
V = amplitude value of the voltage
ω = angular frequency = 2 π f [f = cyclic frequency or simply, frequency]
Ф = phase difference between voltage and current.
Now,
From the question,
V(t) = 230 sin (100t) ---------------(ii)
By comparing equations (i) and (ii) the following holds;
V = 230
ω = 100
Ф = 0
But;
ω = 2 π f = 100
2 π f = 100 [divide both sides by 2]
π f = 50
f = [tex]\frac{50}{\pi }[/tex]Hz
Therefore, the frequency of the voltage is [tex]\frac{50}{\pi }[/tex]Hz
A 1.0-kg ball is attached to the end of a 2.5-m string to form a pendulum. This pendulum is released from rest with the string horizontal. At the lowest point in its swing when it is moving horizontally, the ball collides elastically with a 2.0-kg block initially at rest on a horizontal frictionless surface. What is the speed of the block just after the collision
Answer:
[tex]v_{2}=3.5 m/s[/tex]
Explanation:
Using the conservation of energy we have:
[tex]\frac{1}{2}mv^{2}=mgh[/tex]
Let's solve it for v:
[tex]v=\sqrt{2gh}[/tex]
So the speed at the lowest point is [tex]v=7 m/s[/tex]
Now, using the conservation of momentum we have:
[tex]m_{1}v_{1}=m_{2}v_{2}[/tex]
[tex]v_{2}=\frac{1*7}{2}[/tex]
Therefore the speed of the block after the collision is [tex]v_{2}=3.5 m/s[/tex]
I hope it helps you!
a fly undergoes a displacement of - 5.80 while accelerating at -1.33 m/s^2 for 4.22 s. what was the initial velocity of the fly?
Answer:
[tex]v_i = 1.44\frac{m}{s}[/tex]
Explanation:
The computation of the initial velocity of the fly is shown below:-
But before that we need to do the following calculations
For 4.22 seconds
[tex]\bar v = \frac{-5.80 m}{4.22 s}[/tex]
[tex]= -1.37\frac{m}{s}[/tex]
For uniform acceleration
[tex]\bar v = \frac{v_i +v_f}{2}[/tex]
[tex]= v_i + v_f[/tex]
[tex]= -2.74\frac{m}{s}[/tex]
With initial and final velocities
[tex]= -1.33\frac{m}{s^2}[/tex]
[tex]= \frac{v_i +v_f}{4.22s}[/tex]
[tex]= -v_i + v_f[/tex]
[tex]= -5.61\frac{m}{s}[/tex]
So, the initial velocity is
[tex]v_i = 1.44\frac{m}{s}[/tex]
We simply applied the above steps to reach at the final solution i.e initial velocity
The electric field at the surface of a charged, solid, copper sphere with radius 0.220 mm is 4200 N/CN/C, directed toward the center of the sphere. What is the potential at the center of the sphere, if we take the potential to be zero infinitely far from the sphere?
Answer:
The potential at the center of the sphere is -924 V
Explanation:
Given;
radius of the sphere, R = 0.22 m
electric field at the surface of the sphere, E = 4200 N/C
Since the electric field is directed towards the center of the sphere, the charge is negative.
The Potential is the same at every point in the sphere, and it is given as;
[tex]V = \frac{1}{4 \pi \epsilon_o} \frac{q}{R}[/tex] -------equation (1)
The electric field on the sphere is also given as;
[tex]E = \frac{1}{4 \pi \epsilon _o} \frac{|q|}{R^2}[/tex]
[tex]|q |= 4 \pi \epsilon _o} R^2E[/tex]
Substitute in the value of q in equation (1)
[tex]V = \frac{1}{4 \pi \epsilon_o} \frac{-(4 \pi \epsilon _o R^2E)}{R} \ \ \ \ q \ is \ negative\ because \ E \ is\ directed \ toward \ the \ center\\\\V = -RE\\\\V = -(0.22* 4200)\\\\V = -924 \ V[/tex]
Therefore, the potential at the center of the sphere is -924 V
An elastic band is hung on a hook and a mass is hung on the lower end of the band. When the mass is pulled downward and then released, it vibrates vertically. The equation of motion is s = 9 cos(t) + 9 sin(t), t ≥ 0, where s is measured in centimeters and t in seconds. (Take the positive direction to be downward.) (a) Find the velocity and acceleration at time t.
Answer:
v(t) = s′(t) = −9sin(t)+9cos(t)
a(t) = v′(t) = −9cos(t) −9sin(t)
Explanation:
Given that
s = 9 cos(t) + 9 sin(t), t ≥ 0
Then acceleration and velocity is
v(t) = s′(t) = −9sin(t)+9cos(t)
a(t) = v′(t) = −9cos(t) −9sin(t)
Muons are elementary particles that are formed high in the atmosphere by the interactions of cosmic rays with atomic nuclei. Muons are radioactive and have average lifetimes of about two-millionths of a second. Even though they travel at almost the speed of light, they have so far to travel through the atmosphere that very few should be detected at sea level - at least according to classical physics. Laboratory measurements, however, show that muons in great number do reach the earth's surface. What is the explanation?
Answer:
Muons reach the earth in great amount due to the relativistic time dilation from an earthly frame of reference.
Explanation:
Muons travel at exceedingly high speed; close to the speed of light. At this speed, relativistic effect starts to take effect. The effect of this is that, when viewed from an earthly reference frame, their short half life of about two-millionth of a second is dilated. The dilated time, due to relativistic effects on time for travelling at speed close to the speed of light, gives the muons an extended relative travel time before their complete decay. So in reality, the muon do not have enough half-life to survive the distance from their point of production high up in the atmosphere to sea level, but relativistic effect due to their near-light speed, dilates their half-life; enough for them to be found in sufficient amount at sea level.
Briefly describe the relationship between an equipotential surface and an electric field, and use this to explain why we will plot equipotential lines.
Answer:
E = - dV/dx
Explanation:
Las superficies equipòtenciales son superficie donde el potencial eléctrico es constante por lo cual nos podemos desplazaren ella sin realizar nigun trabajo.
El campo electrico es el campo que existen algún punto en el espacio creado por alguna ddistribucion de carga.
De los antes expuesto las dos magnitudes están relacionadas
E = - dV/dx
por lo cual el potenical es el gradiente del potencial eléctrico.
Como el campo eléctrico sobre un superficie equipotenciales constante, podemos colocar una punta de prueba con un potencial dado y seguir la linea que de una diferencia de potencial constar, lo cual permite visualizar las forma de cada linea equipotencial
a 5.0 charge is placed at the 0 cm mark of a meterstick and a -4.0 charge is placed at the 50 cm mark. what is the electric field at the 30 cm mark
Answer:
-1748*10^N/C
Explanation:
See attached file
A player is positioned 35 m[40 degrees W of S] of the net. He shoot the puck 25 m [E] to a teammate. What second displacement does the puck have to travel in order to make it to the net?
Answer:
x=22.57 m
Explanation:
Given that
35 m in W of S
angle = 40 degrees
25 m in east
From the diagram
The angle
[tex]\theta=90-40=50^o[/tex]
From the triangle OAB
[tex]cos40^o=\frac{35^2+25^2-x^2}{2\times 35\times 25}[/tex]
[tex]1340.57=35^2+25^2-x^2[/tex]
x=22.57 m
Therefore the answer of the above problem will be 22.57 m
g A change in the initial _____ of a projectile changes the range and maximum height of the projectile.
Answer:
Velocity.
Explanation:
Projectile motion is characterized as the motion that an object undergoes when it is thrown into the air and it is only exposed to acceleration due to gravity.
As per the question, 'any change in the initial velocity of the projectile(object having gravity as the only force) would lead to a change in the range as well as the maximum height of the projectile.' To illustrate numerically:
Horizontal range: As per expression:
R= ([tex]u^{2}[/tex]*sin2θ)/g
the range depending on the square of the initial velocity.
Maximum height: As per expression:
H= ([tex]u^{2}[/tex] * [tex]sin^{2}[/tex]θ )/2g
the maximum distance also depends upon square of the initial velocity.
can I get help please?
At t = 0, a battery is connected to a series arrangement of a resistor and an inductor. If the inductive time constant is 36.0 ms, at what time is the rate at which energy is dissipated in the resistor equal to the rate at which energy is stored in the inductor's magnetic field?
Answer:
The rate at which energy is dissipated in the resistor is equal to the rate at which energy is stored in the inductor's magnetic field in 24.95 ms.
Explanation:
The energy stored in the inductor is given as
E₁ = ½LI²
The rate at which energy is stored in the inductor is
(dE₁/dt) = (d/dt) (½LI²)
Since L is a constant
(dE₁/dt) = ½L × 2I (dI/dt) = LI (dI/dt)
(dE₁/dt) = LI (dI/dt)
Rate of Energy dissipated in a resistor = Power = I²R
(dE₂/dt) = I²R
When the rate at which energy is dissipated in the resistor equal to the rate at which energy is stored in the inductor's magnetic field
(dE₁/dt) = (dE₂/dt)
OK (dI/dt) = I²R
L (dI/dt) = IR
Current in a this kind of series setup of inductor and resistor at any time, t, is given as
I = (V/R) (1 - e⁻ᵏᵗ)
k = (1/time constant) = (R/L)
(dI/dt) = (kV/R) e⁻ᵏᵗ = (RV/RL) e⁻ᵏᵗ = (V/L) e⁻ᵏᵗ
L (dI/dt) = IR
L [(V/L) e⁻ᵏᵗ] = R [(V/R) (1 - e⁻ᵏᵗ)
V e⁻ᵏᵗ = V (1 - e⁻ᵏᵗ)
e⁻ᵏᵗ = 1 - e⁻ᵏᵗ
2 e⁻ᵏᵗ = 1
e⁻ᵏᵗ = (1/2) = 0.5
e⁻ᵏᵗ = 0.5
In e⁻ᵏᵗ = In 0.5 = -0.69315
- kt = -0.69315
kt = 0.69315
k = (1/time constant)
Time constant = 36.0 ms = 0.036 s
k = (1/0.036) = 27.78
27.78t = 0.69315
t = (0.69315/27.78) = 0.02495 = 24.95 ms
Hope this Helps!!!
A solid conducting sphere is placed in an external uniform electric field. With regard to the electric field on the sphere's interior, which statement is correct
Complete question:
A solid conducting sphere is placed in an external uniform electric field. With regard to the electric field on the sphere's interior, which statement is correct?
A. the interior field points in a direction parallel to the exterior field
B. There is no electric field on the interior of the conducting sphere.
C. The interior field points in a direction perpendicular to the exterior field.
D. the interior field points in a direction opposite to the exterior field.
Answer:
B. There is no electric field on the interior of the conducting sphere.
Explanation:
Conductors are said to have free charges that move around easily. When the conductor is now placed in a static electric field, the free charges react to attain electrostatic equilibrium (steady state).
Here, a solid conducting sphere is placed in an external uniform electric field. Until the lines of the electric field are perpendicular to the surface, the free charges will move around the spherical conductor, causing polarization. There would be no electric field in the interior of the spherical conductor because there would be movement of free charges in the spherical conductor in response to any field until its neutralization.
Option B is correct.
There is no electric field on the interior of the conducting sphere.
A skater on ice with arms extended and one leg out spins at 3 rev/s. After he draws his arms and the leg in, his moment of inertia is reduced to 1/2. What is his new angular speed
Answer:
The new angular speed is [tex]w = 6 \ rev/s[/tex]
Explanation:
From the question we are told that
The angular velocity of the spin is [tex]w_o = 3 \ rev/s[/tex]
The original moment of inertia is [tex]I_o[/tex]
The new moment of inertia is [tex]I =\frac{I_o}{2}[/tex]
Generally angular momentum is mathematically represented as
[tex]L = I * w[/tex]
Now according to the law of conservation of momentum, the initial momentum is equal to the final momentum hence the angular momentum is constant so
[tex]I * w = constant[/tex]
=> [tex]I_o * w _o = I * w[/tex]
where w is the new angular speed
So
[tex]I_o * 3 = \frac{I_o}{2} * w[/tex]
=> [tex]w = \frac{3 * I_o}{\frac{I_o}{2} }[/tex]
=> [tex]w = 6 \ rev/s[/tex]
2. A pair of narrow, parallel slits sep by 0.25 mm is illuminated by 546 nm green light. The interference pattern is observed on a screen situated at 1.3 m away from the slits. Calculate the distance from the central maximum to the
Answer:
for the first interference m = 1 y = 2,839 10-3 m
for the second interference m = 2 y = 5,678 10-3 m
Explanation:
The double slit interference phenomenon, for constructive interference is described by the expression
d sin θ = m λ
where d is the separation between the slits, λ the wavelength and m an integer that corresponds to the interference we see.
In these experiments in general the observation screen is L >> d, let's use trigonometry to find the angles
tan θ = y / L
with the angle it is small,
tan θ = sin θ / cos θ = sin θ
we substitute
sin θ = y / L
d y / L = m λ
the distance between the central maximum and an interference line is
y = m λ L / d
let's reduce the magnitudes to the SI system
λ = 546 nm = 546 10⁻⁹ m
d = 0.25 mm = 0.25 10⁻³ m
let's substitute the values
y = m 546 10⁻⁹ 1.3 / 0.25 10⁻³
y = m 2,839 10⁻³
the explicit value for a line depends on the value of the integer m, for example
for the first interference m = 1
the distance from the central maximum to the first line is y = 2,839 10-3 m
for the second interference m = 2
the distance from the central maximum to the second line is y = 5,678 10-3 m
A "laser cannon" of a spacecraft has a beam of cross-sectional area A. The maximum electric field in the beam is 2E. The beam is aimed at an asteroid that is initially moving in the direction of the spacecraft. What is the acceleration of the asteroid relative to the spacecraft if the laser beam strikes the asteroid perpendicularly to its surface, and the surface is not reflecting
Answer:
Acceleration of the asteroid relative to the spacecraft = 2ε[tex]E^{2}[/tex]A/m
Explanation:
The maximum electric field in the beam = 2E
cross-sectional area of beam = A
The intensity of an electromagnetic wave with electric field is
I = cε[tex]E_{0} ^{2}[/tex]/2
for [tex]E_{0}[/tex] = 2E
I = 2cε[tex]E^{2}[/tex] ....equ 1
where
I is the intensity
c is the speed of light
ε is the permeability of free space
[tex]E_{0}[/tex] is electric field
Radiation pressure of an electromagnetic wave on an absorbing surface is given as
P = I/c
substituting for I from above equ 1. we have
P = 2cε[tex]E^{2}[/tex]/c = 2ε[tex]E^{2}[/tex] ....equ 2
Also, pressure P = F/A
therefore,
F = PA ....equ 3
where
F is the force
P is pressure
A is cross-sectional area
substitute equ 2 into equ 3, we have
F = 2ε[tex]E^{2}[/tex]A
force on a body = mass x acceleration.
that is
F = ma
therefore,
a = F/m
acceleration of the asteroid will then be
a = 2ε[tex]E^{2}[/tex]A/m
where m is the mass of the asteroid.
A ball is thrown directly downward with an initial speed of 7.95 m/s, from a height of 29.0 m. After what time interval does it strike the ground?
Answer: after 1.75 seconds
Explanation:
The only force acting on the ball is the gravitational force, so the acceleration will be:
a = -9.8 m/s^2
the velocity can be obtained by integrating over time:
v = -9.8m/s^2*t + v0
where v0 is the initial velocity; v0 = -7.95 m/s.
v = -9.8m/s^2*t - 7.95 m/s.
For the position we integrate again:
p = -4.9m/s^2*t^2 - 7.95 m/s*t + p0
where p0 is the initial position: p0 = 29m
p = -4.9m/s^2*t^2 - 7.95 m/s*t + 29m
Now we want to find the time such that the position is equal to zero:
0 = -4.9m/s^2*t^2 - 7.95 m/s*t + 29m
Then we solve the Bhaskara's equation:
[tex]t = \frac{7.95 +- \sqrt{7.95^2 +4*4.9*29} }{-2*4.9} = \frac{7.95 +- 25.1}{9.8}[/tex]
Then the solutions are:
t = (7.95 + 25.1)/(-9.8) = -3.37s
t = (7.95 - 25.1)/(-9.8) = 1.75s
We need the positive time, then the correct answer is 1.75s
Two carts are connected by a loaded spring on a horizontal, frictionless surface. The spring is released and the carts push away from each other. Cart 1 has mass M and Cart 2 has mass M/3.
a) Is the momentum of Cart 1 conserved?
Yes
No
It depends on M
b) Is the momentum of Cart 2 conserved?
Yes
No
It depends on M
c) Is the total momentum of Carts 1 and 2 conserved?
Yes
No
It depends on M
d) Which cart ends up moving faster?
Cart 1
Cart 2
They move at the same speed
e) If M = 6 kg and Cart 1 moves with a speed of 16 m/s, what is the speed of Cart 2?
0 m/s
4.0 m/s
5.3 m/s
16 m/s
48 m/s
64 m/s
Answer:
a) yes
b) no
c) yes
d)Cart 2 with mass [tex]\frac{M}{3}[/tex] is expected to be more faster
e) u₂ = 48 m/s
Explanation:
a) the all out linear momentum of an arrangement of particles of Cart 1 not followed up on by external forces is constant.
b) the linear momentum of Cart 2 will be acted upon by external force by Cart 1 with mass M, thereby it's variable and the momentum is not conserved
c) yes, the momentum is conserved because no external force acted upon it and both Carts share the same velocity after the reaction
note: m₁u₁ + m₂u₂ = (m₁ + m₂)v
d) Cart 2 with mass [tex]\frac{M}{3}[/tex] will be faster than Cart 1 because Cart 2 is three times lighter than Cart 1.
e) Given
m₁= M
u₁ = 16m/s
m₂ =[tex]\frac{M}{3}[/tex]
u₂ = ?
from law of conservation of momentum
m₁u₁= m₂u₂
M× 16 = [tex]\frac{M}{3}[/tex] × u₂(multiply both sides by 3)
therefore, u₂ = [tex]\frac{3(M .16)}{M}[/tex] ("." means multiplication)
∴u₂ = 3×16 = 48 m/s
Calculate the ideal banking angle in degrees for a gentle turn of 1.88 km radius on a highway with a 136.3 km/hr speed limit, assuming everyone travels at the speed limit.
Answer:
Ф = 4.4°Explanation:
given:
radius (r) = 1.88 km
velocity (v) = 136.3 km/hr
required:
banking angle ∡ ?
first:
convert 1.88 km to m = 1.88km * 1000m / 1km
r = 1880 m
convert velocity v = 136.3 km/hr to m/s = 136.3 km/hr * (1000 m/ 3600s)
v = 37.86 m/s
now.. calculate the angle
Ф = inv tan (v² / r * g) we know that gravity = 9.8 m/s²
Ф = inv tan (37.86² / (1880 * 9.8))
Ф = 4.4°
If, instead, the ball is revolved so that its speed is 3.7 m/s, what angle does the cord make with the vertical?
Complete Question:
A 0.50-kg ball that is tied to the end of a 1.5-m light cord is revolved in a horizontal plane, with the cord making a 30° angle with the vertical.
(a) Determine the ball’s speed. (b) If, instead, the ball is revolved so that its
speed is 3.7 m/s, what angle does the cord make with the vertical?
(Check attached image for the diagram.)
Answer:
(a) The ball’s speed, v = 2.06 m/s
(b) The angle the cord makes with the vertical is 50.40⁰
Explanation:
If the ball is revolved in a horizontal plane, it will form a circular trajectory,
the radius of the circle, R = Lsinθ
where;
L is length of the string
The force acting on the ball is given as;
F = mgtanθ
This above is also equal to centripetal force;
[tex]mgTan \theta = \frac{mv^2}{R} \\\\Recall, R = Lsin \theta\\\\mgTan \theta = \frac{mv^2}{Lsin \theta}\\\\v^2 = glTan \theta sin \theta\\\\v = \sqrt{glTan \theta sin \theta} \\\\v = \sqrt{(9.8)(1.5)(Tan30)(sin30)} \\\\v = 2.06 \ m/s[/tex]
(b) when the speed is 3.7 m/s
[tex]v = \sqrt{glTan \theta sin \theta} \ \ \ ;square \ both \ sides\\\\v^2 = glTan \theta sin \theta\\\\v^2 = gl(\frac{sin \theta}{cos \theta}) sin \theta\\\\v^2 = \frac{gl*sin^2 \theta}{cos \theta} \\\\v^2 = \frac{gl*(1- cos^2 \theta)}{cos \theta}\\\\gl*(1- cos^2 \theta) = v^2cos \theta\\\\(9.8*1.5)(1- cos^2 \theta) = (3.7^2)cos \theta\\\\14.7 - 14.7cos^2 \theta = 13.69cos \theta\\\\14.7cos^2 \theta + 13.69cos \theta - 14.7 = 0 \ \ \ ; this \ is \ quadratic \ equation\\\\[/tex]
[tex]Cos\theta = \frac{13.69\sqrt{13.69^2 -(-4*14.7*14.7)} }{14.7} \\\\Cos \theta = 0.6374\\\\\theta = Cos^{-1}(0.6374)\\\\\theta = 50.40 ^o[/tex]
Therefore, the angle the cord makes with the vertical is 50.40⁰
A 10 gauge copper wire carries a current of 23 A. Assuming one free electron per copper atom, calculate the magnitude of the drift velocity of the electrons.
Question:
A 10 gauge copper wire carries a current of 15 A. Assuming one free electron per copper atom, calculate the drift velocity of the electrons. (The cross-sectional area of a 10-gauge wire is 5.261 mm².)
Answer:
3.22 x 10⁻⁴ m/s
Explanation:
The drift velocity (v) of the electrons in a wire (copper wire in this case) carrying current (I) is given by;
v = [tex]\frac{I}{nqA}[/tex]
Where;
n = number of free electrons per cubic meter
q = electron charge
A = cross-sectional area of the wire
First let's calculate the number of free electrons per cubic meter (n)
Known constants:
density of copper, ρ = 8.95 x 10³kg/m³
molar mass of copper, M = 63.5 x 10⁻³kg/mol
Avogadro's number, Nₐ = 6.02 x 10²³ particles/mol
But;
The number of copper atoms, N, per cubic meter is given by;
N = (Nₐ x ρ / M) -------------(ii)
Substitute the values of Nₐ, ρ and M into equation (ii) as follows;
N = (6.02 x 10²³ x 8.95 x 10³) / 63.5 x 10⁻³
N = 8.49 x 10²⁸ atom/m³
Since there is one free electron per copper atom, the number of free electrons per cubic meter is simply;
n = 8.49 x 10²⁸ electrons/m³
Now let's calculate the drift electron
Known values from question:
A = 5.261 mm² = 5.261 x 10⁻⁶m²
I = 23A
q = 1.6 x 10⁻¹⁹C
Substitute these values into equation (i) as follows;
v = [tex]\frac{I}{nqA}[/tex]
v = [tex]\frac{23}{8.49*10^{28} * 1.6 *10^{-19} * 5.261*10^{-6}}[/tex]
v = 3.22 x 10⁻⁴ m/s
Therefore, the drift electron is 3.22 x 10⁻⁴ m/s
What will be the volume and density of stone if mass of stone is 10 gram .please tell the answer fast it's very urgent I will mark as a brain me answer if you will answer it correct.
Answer:
[tex]\large \boxed{\text{3.3 cm}^{3}}[/tex]
Explanation:
Assume the stone consists of basalt, which has a density of 3.0 g/cm³.
[tex]\rho = \text{10 g}\times\dfrac{\text{1 cm}^{3}}{\text{3.0 g}} = \text{3.3 cm}^{3}\\\\\text{The volume of the stone is $\large \boxed{\textbf{3.3 cm}^{3}}$}[/tex]
A 1.5-kg mass attached to spring with a force constant of 20.0 N/m oscillates on a horizontal, frictionless track. At t = 0, the mass is released from rest at x = 10.0 cm. ( That is, the spring is stretched by 10.0 cm.) (a) Determine the frequency of the oscillations. (b) Determine the maximum speed of the mass. Where dos the maximum speed occur? (c) Determine the maximum acceleration of the mass. Where does the maximum acceleration occur? (d) Determine the total energy of teh oscillating system. (e) Express the displacement as a function of time.
Answer:
(a) f = 0.58Hz
(b) vmax = 0.364m/s
(c) amax = 1.32m/s^2
(d) E = 0.1J
(e) [tex]x(t)=0.1m\ cos(2\pi(0.58s^{-1})t)[/tex]
Explanation:
(a) The frequency of the oscillation, in a spring-mass system, is calulated by using the following formula:
[tex]f=\frac{1}{2\pi}\sqrt{\frac{k}{m}}[/tex] (1)
k: spring constant = 20.0N/m
m: mass = 1.5kg
you replace the values of m and k for getting f:
[tex]f=\frac{1}{2\pi}\sqrt{\frac{20.0N/m}{1.5kg}}=0.58s^{-1}=0.58Hz[/tex]
The frequency of the oscillation is 0.58Hz
(b) The maximum speed is given by:
[tex]v_{max}=\omega A=2\pi f A[/tex] (2)
A: amplitude of the oscillations = 10.0cm = 0.10m
[tex]v_{max}=2\pi (0.58s^{-1})(0.10m)=0.364\frac{m}{s}[/tex]
The maximum speed of the mass is 0.364 m/s.
The maximum speed occurs when the mass passes trough the equilibrium point of the oscillation.
(c) The maximum acceleration is given by:
[tex]a_{max}=\omega^2A=(2\pi f)^2 A[/tex]
[tex]a_{max}=(2\pi (0.58s^{-1}))(0.10m)=1.32\frac{m}{s^2}[/tex]
The maximum acceleration is 1.32 m/s^2
The maximum acceleration occurs where the elastic force is a maximum, that is, where the mass is at the maximum distance from the equilibrium point, that is, the acceleration.
(d) The total energy of the system is:
[tex]E=\frac{1}{2}kA^2=\frac{1}{2}(20.0N/m)(0.10m)^2=0.1J[/tex]
The total energy is 0.1J
(e) The displacement as a function of time is:
[tex]x(t)=Acos(\omega t)=Acos(2\pi ft)\\\\x(t)=0.1m\ cos(2\pi(0.58s^{-1})t)[/tex]
what is the preferred method of using percentage data by using a circle divided into sections
Answer:
A pie chart is a type of graph in which a circle is divided into sectors that each represents a proportion of the whole
Explanation:
pie charts are a useful way to organize data in order to see the size of components relative to the whole.
Consider a conducting rod of length 31 cm moving along a pair of rails, and a magnetic field pointing perpendicular to the plane of the rails. At what speed (in m /s) must the sliding rod move to produce an emf of 0.75 V in a 1.75 T field?
Answer:
The speed of the rod is 1.383 m/s
Explanation:
Given;
length of the conducting rod, L = 31 cm = 0.31 m
induced emf on the rod, emf = 0.75V
magnetic field around the rod, B = 1.75 T
Apply the following Faraday's equation for electromagnetic induction in a moving rod to determine the speed of the rod.
emef = BLv
where;
B is the magnetic field
L is length of the rod
v is the speed of the rod
v = emf / BL
v = (0.75) / (1.75 x 0.31)
v = 1.383 m/s
Therefore, the speed of the rod is 1.383 m/s
The Law of Biot-Savart shows that the magnetic field of an infinitesimal current element decreases as 1/r2. Is there anyway you could put together a complete circuit (any closed path of current-carrying wire) whose field exhibits this same 1/r^2 decrease in magnetic field strength? Explain your reasoning.
Answer and Explanation:
There is no probability of obtaining such a circuit of closed track current carrying wire whose field of magnitude displays i.e. [tex]B \alpha \frac{1}{r^2}[/tex]
The magnetic field is a volume of vectors
And [tex]\phi\ bds = 0[/tex]. This ensures isolated magnetic poles or magnetic charges would not exit
Therefore for a closed path, we never received magnetic field that followed the [tex]B \alpha \frac{1}{r^2}[/tex] it is only for the simple current-carrying wire for both finite or infinite length.
_____________ friction is the interlocking of surfaces due to irregularities on the surfaces preventing those surfaces from moving/sliding against each other. For surfaces moving/sliding on each other, ___________ friction overwhelms kinetic friction to that movement/sliding. Kinetic friction is alway larger than ____________ friction. Kinetic friction is alway equal to _________ friction.
Answer:
STATIC, STATIC
KINETIC friction is less than static friction
Explanation:
In this exercise you are asked to complete the sentences with the correct words.
STATIC friction prevents the relative movement of two surfaces in contact.
For moving surfaces the friction is STATIC is greater than the kinetic friction.
For the last two sentences I think they are misspelled, the correct thing is
KINETIC friction is less than static friction
6. Two forces of 50 N and 30 N, respectively, are acting on an object. Find the net force (in
N) on the object if
the forces are acting in the same direction
b. the forces are acting in opposite directions.
Answer:
same direction = 80 (n)
opposite direction = 20 (n) going one direction
Explanation:
same direction means they are added to each other
and opposite means acting on eachother