Answer: The angular velocity of the large wheel is 4.26 rad/s.
Angular velocity of the small wheel at the top w = 5 rad/s. mass m1 = 5 kg. radius r1 = 0.2 m.
Angular velocity of the small wheel on the left is w1 = 3 rad/s. mass m1 = 5 kg. radius r1 = 0.2 m.
Angular velocity of the small wheel on the right is w2 = 4 rad/s. mass m1 = 5 kg. radius r1 = 0.2 m.
The large wheel has a mass of m2 = 10 kg. radius of r2 = 0.4 m.
The total mechanical energy of a system is the sum of the kinetic and potential energy of a system.
kinetic energy is K.E = 1/2mv².
Potential energy is P.E = mgh.
In this case, there is no height change so there is no potential energy.
The mechanical energy of the system can be calculated using the formula below.
E = K.E(1) + K.E(2) + K.E(3)
where, K.E(i) = 1/2 m(i) v(i)² = 1/2 m(i) r(i)² ω(i)²
K.E(1) = 1/2 × 5 × (0.2)² × 5² = 1 J
K.E(2) = 1/2 × 5 × (0.2)² × 3² = 0.54 J
K.E(3) = 1/2 × 5 × (0.2)² × 4² = 0.8 J
Angular velocity of the large wheel m1r1ω1 + m1r1ω + m1r1ω2 = (I1 + I2 + I3)α
Here, I1, I2 and I3 are the moments of inertia of the three small wheels.
The moment of inertia of a wheel is given by I = (1/2)mr²
Here, I1 = I2 = I3 = (1/2) (5) (0.2)² = 0.1 kg m².
The moment of inertia of the large wheel: I2 = (1/2) m2 r2² = (1/2) (10) (0.4)²
= 0.8 kg m²
Putting the values in the above equation and solving, we get, α = 2.15 rad/s²ω = 4.26 rad/s
Therefore, the angular velocity of the large wheel is 4.26 rad/s.
Learn more about Angular velocity: https://brainly.com/question/20432894
#SPJ11
Explain each of the following cases of magnification. magnification (M) M>1, M<1 and M=1 explain how you can find the image of a faraway object using a convex lens. Where will the image be formed?
What lens is used in a magnifying lens? Explain the working of a magnifying lens.
Magnification (M) refers to the degree of enlargement or reduction of an image compared to the original object. When M > 1, the image is magnified; when M < 1, the image is reduced; and when M = 1, the image has the same size as the object.
To find the image of a faraway object using a convex lens, a converging lens is typically used. The image will be formed on the opposite side of the lens from the object, and its location can be determined using the lens equation and the magnification formula.
A magnifying lens is a convex lens with a shorter focal length. It works by creating a virtual, magnified image of the object that appears larger when viewed through the lens.
1. M > 1 (Magnification): When the magnification (M) is greater than 1, the image is magnified. This means that the size of the image is larger than the size of the object. It is commonly observed in devices like magnifying glasses or telescopes, where objects appear bigger and closer.
2. M < 1 (Reduction): When the magnification (M) is less than 1, the image is reduced. In this case, the size of the image is smaller than the size of the object. This type of magnification is used in devices like microscopes, where small objects need to be viewed in detail.
3. M = 1 (Unity Magnification): When the magnification (M) is equal to 1, the image has the same size as the object. This occurs when the image and the object are at the same distance from the lens. It is often seen in simple lens systems used in photography or basic optical systems.
To find the image of a faraway object using a convex lens, a converging lens is used. The image will be formed on the opposite side of the lens from the object. The location of the image can be determined using the lens equation:
1/f = 1/d₀ + 1/dᵢ
where f is the focal length of the lens, d₀ is the object distance, and dᵢ is the image distance. By rearranging the equation, we can solve for dᵢ:
1/dᵢ = 1/f - 1/d₀
The magnification (M) can be calculated using the formula:
M = -dᵢ / d₀
A magnifying lens is a convex lens with a shorter focal length. It works by creating a virtual, magnified image of the object that appears larger when viewed through the lens. This is achieved by placing the object closer to the lens than its focal length.
To learn more about Magnification click here brainly.com/question/21370207
#SPJ11
The
speed of a car is found by dividing the distance traveled by the
time required to travel that distance. Consider a car that traveled
18.0 miles in 0.969 hours. What's the speed of car in km / h
(k
The speed of the car is approximately 29.02 km/h, given that it traveled 18.0 miles in 0.969 hours.
To convert the speed of the car from miles per hour to kilometers per hour, we need to use the conversion factor that 1 mile is equal to 1.60934 kilometers.
Given:
Distance traveled = 18.0 milesTime taken = 0.969 hoursTo calculate the speed of the car, we divide the distance traveled by the time taken:
Speed (in miles per hour) = Distance / Time
Speed (in miles per hour) = 18.0 miles / 0.969 hours
Now, we can convert the speed from miles per hour to kilometers per hour by multiplying it by the conversion factor:
Speed (in kilometers per hour) = Speed (in miles per hour) × 1.60934
Let's calculate the speed in kilometers per hour:
Speed (in kilometers per hour) = (18.0 miles / 0.969 hours) × 1.60934
Speed (in kilometers per hour) = 29.02 km/h
Therefore, the speed of the car is approximately 29.02 km/h.
The complete question should be:
The speed of a car is found by dividing the distance traveled by the time required to travel that distance. Consider a car that traveled 18.0 miles in 0.969 hours. What's the speed of car in km / h (kilometer per hour)?
To learn more about speed, Visit:
https://brainly.com/question/13262646
#SPJ11
At the starting gun, a runner accelerates at 1.9 m>s2 for 5.2 s. The runner’s acceleration is zero for the rest of the race. What is the speed of the runner (a) at t = 2.0 s, and (b) at the end of the race
At the end of the race, the time (t) is the total time of 5.2 seconds. To solve this problem, we can use the equations of motion. The equations of motion for uniformly accelerated linear motion are:
v = u + at
s = ut + (1/2)at^2
v^2 = u^2 + 2as
v = final velocity
u = initial velocity
a = acceleration
t = time
s = displacement
Initial velocity (u) = 0 m/s (since the runner starts from rest)
Acceleration (a) = 1.9 m/s^2
Time (t) = 5.2 s
(a) To find the speed at t = 2.0 s:
v = u + at
v = 0 + (1.9)(2.0)
v = 0 + 3.8
v = 3.8 m/s
Therefore, the speed of the runner at t = 2.0 s is 3.8 m/s.
(b) To find the speed at the end of the race:
The runner's acceleration is zero for the rest of the race. This means that the runner continues to move with a constant velocity after 5.2 seconds.
Since the acceleration is zero, we can use the equation:
v = u + at
At the end of the race, the time (t) is the total time of 5.2 seconds.
Learn more about accelerated here : brainly.com/question/32899180
#SPJ11
Please Help
A simple ac circuit is composed of an inductor connected across the terminals of an ac power source. If the frequency of the source is halved, what happens to the reactance of the inductor? It is unch
When the frequency of an AC power source is halved in a simple AC circuit with an inductor, the reactance of the inductor increases.
The reactance of an inductor is directly proportional to the frequency of the AC power source. Reactance is the opposition that an inductor presents to the flow of alternating current. It is determined by the formula Xl = 2πfL, where Xl is the inductive reactance, f is the frequency, and L is the inductance.
When the frequency is halved, the value of f in the formula decreases. As a result, the inductive reactance increases. This means that the inductor offers greater opposition to the flow of current, causing the current to be impeded.
Halving the frequency of the AC power source effectively reduces the rate at which the magnetic field in the inductor changes, leading to an increase in the inductive reactance. It is important to consider this relationship between frequency and reactance when designing and analyzing AC circuits with inductors.
In conclusion, when the frequency of an AC power source is halved in a simple AC circuit with an inductor, the reactance of the inductor increases, resulting in greater opposition to the flow of current.
To know more about Frequency visit-
brainly.com/question/14320803
#SPJ11
A woman is standing on a bathroom scale in an elevator that is not moving. The balance reads 500 N. The elevator then moves downward at a constant speed of 5 m/s. What is the reading on the scale while the elevator is descending at constant speed?
d. 500N
e. 750N
b. 250N
c. 450N
a. 100N
Two point-shaped masses m and M are separated by a distance d. If the separation d remains fixed and the masses are increased to the values 3m and 3M respectively, how will the gravitational force between them change?
d. The force will be nine times greater.
b. The force will be reduced to one ninth.
e. It is impossible to determine without knowing the numerical values of m, M, and d.
c. The force will be three times greater.
a. The force will be reduced to one third.
The reading on the scale while the elevator is descending at a constant speed is 500N (d). The gravitational force between the masses will be nine times greater when the masses are increased to 3m and 3M (d).
When the elevator is not moving, the reading on the scale is 500N, which represents the normal force exerted by the floor of the elevator on the woman. This normal force is equal in magnitude and opposite in direction to the gravitational force acting on the woman due to her weight.
When the elevator moves downward at a constant speed of 5 m/s, it means that the elevator and everything inside it, including the woman, are experiencing the same downward acceleration. In this case, the woman and the scale are still at rest relative to each other because the downward acceleration cancels out the gravitational force.
As a result, the reading on the scale remains the same at 500N. This is because the normal force provided by the scale continues to balance the woman's weight, preventing any change in the scale reading.
Therefore, the reading on the scale while the elevator is descending at a constant speed remains 500N, which corresponds to option d. 500N.
Regarding the gravitational force between the point-shaped masses, according to Newton's law of universal gravitation, the force between two masses is given by:
F = G × (m1 × m2) / r²,
where
F is the gravitational forceG is the gravitational constantm1 and m2 are the massesr is the separation distance between the massesIn this case, the separation distance d remains fixed, but the masses are increased to 3m and 3M. Plugging these values into the equation, we get:
New force (F') = G × (3m × 3M) / d² = 9 × (G × m × M) / d² = 9F,
where F is the original force between the masses.Therefore, the gravitational force between the masses will be nine times greater when the masses are increased to 3m and 3M, which corresponds to option d. The force will be nine times greater.
To learn more about gravitational force, Visit:
https://brainly.com/question/27943482
#SPJ11
1. (1 p) An object has a kinetic energy of 275 J and a linear momentum of 25 kg m/s. Determine the speed and mass of the object.
An object has a kinetic energy of 275 J and a linear momentum of 25 kg m/s. The speed and mass of the object is 1.136 m/s and 22 kg respectively.
To determine the speed and mass of the object, we can use the formulas for kinetic energy and linear momentum.
Kinetic Energy (KE) = (1/2) × mass (m) × velocity squared (v²)
Linear Momentum (p) = mass (m) × velocity (v)
Kinetic Energy (KE) = 275 J
Linear Momentum (p) = 25 kg m/s
From the equation for kinetic energy, we can solve for velocity (v):
KE = (1/2) × m × v²
2 × KE = m × v²
2 × 275 J = m × v²
550 J = m × v²
From the equation for linear momentum, we have:
p = m × v
v = p / m
Plugging in the given values of linear momentum and kinetic energy, we have:
25 kg m/s = m × v
25 kg m/s = m × (550 J / m)
m = 550 J / 25 kg m/s
m = 22 kg
Now that we have the mass, we can substitute it back into the equation for velocity:
v = p / m
v = 25 kg m/s / 22 kg
v = 1.136 m/s
Therefore, the speed of the object is approximately 1.136 m/s, and the mass of the object is 22 kg.
To know more about kinetic energy here
https://brainly.com/question/999862
#SPJ4
A 28 g ball of clay traveling east at 3.2 m/s collides with a 32 g ball of clay traveling north at 2.8 m/s
The two balls will move together at a velocity of 2.987 m/s at an angle between east and north after the collision.
When the 28 g ball of clay traveling east at 3.2 m/s collides with the 32 g ball of clay traveling north at 2.8 m/s, the two balls will stick together due to the conservation of momentum.
To solve this problem, we can use the principle of conservation of momentum, which states that the total momentum before the collision is equal to the total momentum after the collision.
The momentum of an object is given by the product of its mass and velocity. Therefore, the momentum of the 28 g ball of clay before the collision is (28 g) * (3.2 m/s) = 89.6 g·m/s east, and the momentum of the 32 g ball of clay before the collision is (32 g) * (2.8 m/s) = 89.6 g·m/s north.
After the collision, the two balls stick together, so their total mass is 28 g + 32 g = 60 g. The momentum of the combined mass can be calculated by adding the momenta of the individual balls before the collision.
Therefore, the total momentum after the collision is 89.6 g·m/s east + 89.6 g·m/s north = 179.2 g·m/s at an angle between east and north.
To calculate the velocity of the combined balls after the collision, divide the total momentum by the total mass: (179.2 g·m/s) / (60 g) = 2.987 m/s.
To know more about velocity visit:-
https://brainly.com/question/30559316
#SPJ11
As a new electrical technician, you are designing a large solenoid to produce a uniform 0.130 T magnetic field near the center of the solenoid. You have enough wire for 3000 circular turns. This solenoid must be
52.0 cm long and 2.80 cm in diameter.
What current will you need to produce the necessary field?
The magnetic field produced inside a solenoid is given asB=μ₀(n/l)I ,Where,μ₀= 4π×10^-7 T m A^-1is the permeability of free space,n is the number of turns per unit length,l is the length of the solenoid, andI is the current flowing through the wire.The solenoid has 3000 circular turns and is 52.0 cm long and 2.80 cm in diameter, and the magnetic field produced near the center of the solenoid is 0.130 T.Thus,The length of the solenoid,l= 52.0 cm = 0.52 mn= 3000 circular turns/lπd²n = 3000 circular turns/π(0.028 m)²I = ?The magnetic field equation can be rearranged to solve for current asI= (Bμ₀n/l),whereB= 0.130 Tμ₀= 4π×10^-7 T m A^-1n= 3000 circular turns/π(0.028 m)²l= 0.52 mThus,I= (0.130 T×4π×10^-7 T m A^-1×3000 circular turns/π(0.028 m)²)/0.52 m≈ 5.49 ATherefore, the current required to produce the required magnetic field is approximately 5.49 A.
The answer is a current of 386 A will be necessary. We know that the solenoid must produce a magnetic field of 0.130 T and that it has 3000 circular turns. We can determine the number of turns per unit length as follows: n = N/L, where: N is the total number of turns, L is the length
Substituting the given values gives us: n = 3000/(0.52 m) = 5769 turns/m
We can use Ampere's law to determine the current needed to produce the necessary field. According to Ampere's law, the magnetic field inside a solenoid is given by:
B = μ₀nI,where: B is the magnetic field, n is the number of turns per unit length, I is the current passing through the solenoid, μ₀ is the permeability of free space
Solving for the current: I = B/(μ₀n)
Substituting the given values gives us:I = 0.130 T/(4π×10⁻⁷ T·m/A × 5769 turns/m) = 386 A
I will need a current of 386 A to produce the necessary magnetic field.
Learn more about magnetic field: https://brainly.com/question/14411049
#SPJ11
Consider a series RLC circuit having the parameters R=200Ω L=663mH , and C=26.5µF. The applied voltage has an amplitude of 50.0V and a frequency of 60.0Hz. Find (d) the maximum voltage ΔVL across the inductor and its phase relative to the current.
The maximum voltage [tex]ΔVL[/tex]across the inductor is approximately 19.76V, and its phase relative to the current is 90 degrees.
To find the maximum voltage [tex]ΔVL[/tex]across the inductor and its phase relative to the current, we can use the formulas for the impedance of an RLC circuit.
First, we need to calculate the angular frequency ([tex]ω[/tex]) using the given frequency (f):
[tex]ω = 2πf = 2π * 60 Hz = 120π rad/s[/tex]
Next, we can calculate the inductive reactance (XL) and the capacitive reactance (XC) using the formulas:
[tex]XL = ωL = 120π * 663mH = 79.04Ω[/tex]
[tex]XC = 1 / (ωC) = 1 / (120π * 26.5µF) ≈ 0.1Ω[/tex]
Now, we can calculate the total impedance (Z) using the formulas:
[tex]Z = √(R^2 + (XL - XC)^2) ≈ 200Ω[/tex]
The maximum voltage across the inductor can be calculated using Ohm's Law:
[tex]ΔVL = I * XL[/tex]
We need to find the current (I) first. Since the applied voltage has an amplitude of 50.0V, the current amplitude can be calculated using Ohm's Law:
[tex]I = V / Z ≈ 50.0V / 200Ω = 0.25A[/tex]
Substituting the values, we get:
[tex]ΔVL = 0.25A * 79.04Ω ≈ 19.76V[/tex]
The phase difference between the voltage across the inductor and the current can be found by comparing the phase angles of XL and XC. Since XL > XC, the voltage across the inductor leads the current by 90 degrees.
To know more about inductor visit:
https://brainly.com/question/31503384
#SPJ11
Show that the first Covarient derivative of metric tensor th
The first covariant derivative of the metric tensor is a mathematical operation that describes the change of the metric tensor along a given direction. It is denoted as ∇μgνρ and can be calculated using the Christoffel symbols and the partial derivatives of the metric tensor.
The metric tensor in general relativity describes the geometry of spacetime. The first covariant derivative of the metric tensor, denoted as ∇μgνρ, represents the change of the metric tensor components along a particular direction specified by the index μ. It is used in various calculations involving curvature and geodesic equations.
To calculate the first covariant derivative, we can use the Christoffel symbols, which are related to the metric tensor and its partial derivatives. The Christoffel symbols can be expressed as:
Γλμν = (1/2) gλσ (∂μgσν + ∂νgμσ - ∂σgμν)
Then, the first covariant derivative of the metric tensor is given by:
∇μgνρ = ∂μgνρ - Γλμν gλρ - Γλμρ gνλ
By substituting the appropriate Christoffel symbols and metric tensor components into the equation, we can calculate the first covariant derivative. This operation is essential in understanding the curvature of spacetime and solving field equations in general relativity.
To learn more about tensor click here brainly.com/question/31184754
#SPJ11
The dampening material in an ultrasound system is often made of
_________, and its function is to _______the pulses.
The dampening material used in an ultrasound system is often made of rubber or silicone, and its function is to absorb or reduce the intensity of the ultrasound pulses.
In an ultrasound system, the dampening material is an essential component that helps optimize the performance of the device. The material used for dampening is typically rubber or silicone, which have excellent acoustic properties. The primary purpose of the dampening material is to absorb or reduce the intensity of the ultrasound pulses emitted by the transducer.
Ultrasound pulses consist of high-frequency waves that are emitted and received by the transducer. When these pulses travel through the body, they encounter various interfaces between different tissues and organs, leading to reflections and echoes. If the ultrasound pulses were not dampened, they could bounce back and interfere with subsequent pulses, causing artifacts and reducing image quality.
By placing a layer of rubber or silicone as the dampening material in the ultrasound system, the pulses encounter resistance as they pass through the material. This resistance helps absorb or attenuate the energy of the pulses, reducing their intensity before they reach the patient's body. As a result, the echoes and reflections are less likely to interfere with subsequent pulses, allowing for clearer and more accurate imaging.
The choice of rubber or silicone as the dampening material is based on their ability to effectively absorb and attenuate ultrasound waves. These materials have properties that allow them to convert the mechanical energy of the ultrasound pulses into heat, dissipating the energy and minimizing reflection or transmission of the waves. Additionally, rubber and silicone are flexible and easily conform to the shape of the transducer, ensuring good acoustic contact and optimal dampening of the ultrasound pulses.
In conclusion, the dampening material used in an ultrasound system, typically made of rubber or silicone, serves the vital function of absorbing or reducing the intensity of ultrasound pulses. By attenuating the energy of the pulses, the dampening material helps prevent artifacts and interference, leading to improved image quality and more accurate diagnostic results.
Learn more about ultrasound here:
brainly.com/question/31609447
#SPJ11
7. 7. A 1000Kg car moves at 10m/s, determine the momentum of the
car.
The momentum of the car is 10,000 kg·m/s
The momentum of an object is calculated by multiplying its mass by its velocity. In this case, the car has a mass of 1000 kg and is moving at a velocity of 10 m/s.
The momentum (p) of the car can be calculated using the formula:
p = mass × velocity
Substituting the given values, we have:
p = 1000 kg × 10 m/s
p = 10,000 kg·m/s
Therefore, the momentum of the car is 10,000 kg·m/s. Momentum is a vector quantity, meaning it has both magnitude and direction. In this case, the direction of the momentum will be the same as the direction of the car's velocity.
Learn more about momentum here:
https://brainly.com/question/1042017
#SPJ11
Two masses mAmA = 2.3 kg and mBmB = 4.0 kg are on inclines and are connected together by a string as shown in (Figure 1). The coefficient of kinetic friction between each mass and its incline is μk = 0.30.If mA moves up, and mB moves down, determine the magnitude of their acceleration.
In the given problem, two masses, mA = 2.3 kg and mB = 4.0 kg, are connected by a string and placed on inclines. The coefficient of kinetic friction between each mass and its incline is given as μk = 0.30.
The task is to determine the magnitude of the acceleration of the masses when mA moves up and mB moves down. To find the magnitude of the acceleration, we need to consider the forces acting on the masses.
When mA moves up, the force of gravity pulls it downward while the tension in the string pulls it upward. The force of kinetic friction opposes the motion of mA. When mB moves down, the force of gravity pulls it downward, the tension in the string pulls it upward, and the force of kinetic friction opposes the motion of mB. The net force acting on each mass can be determined by considering the forces along the inclines.
Using Newton's second law, we can write the equations of motion for each mass. The net force is equal to the product of mass and acceleration. The tension in the string cancels out in the equations, leaving us with the force of gravity and the force of kinetic friction. By equating the net force to mass times acceleration for each mass, we can solve for the acceleration.
Additionally, the force of kinetic friction can be calculated using the coefficient of kinetic friction and the normal force, which is the component of the force of gravity perpendicular to the incline. The normal force can be determined using the angle of the incline and the force of gravity.
By solving the equations of motion and calculating the force of kinetic friction, we can determine the magnitude of the acceleration of the masses when mA moves up and mB moves down.
Learn more about friction here:
brainly.com/question/28356847
#SPJ11
(a) What do you understand by the terms renewable, non- renewable and sustainable when discussing energy sources? Give examples of each. Discuss how an energy source can be renewable but not sustainable, again with an example. (b) Calculate how much power can be produced from a wind turbine that has a power coefficient of 0.4 and a blade radius of 50 m if the wind speed is 12 m/s. (c) How many of these turbines (rounded up to the nearest whole number) would be needed if wind power could supply 100% of the household energy needs of a UK city of 750,000 homes? (d) If the same amount of power is needed from a hydroelectric power station as can be produced by the single turbine in part (a), calculate the mass of water per second that needs to fall on to the generator from a height of 50 m. Assume in this case the generator is 80% efficient.
a) When discussing energy sources, the terms renewable,
non-renewable, and sustainable have the following meanings:
Renewable Energy Sources: These are energy sources that are naturally replenished and have an essentially unlimited supply. They are derived from sources that are constantly renewed or regenerated within a relatively short period. Examples of renewable energy sources include:
Solar energy: Generated from sunlight using photovoltaic cells or solar thermal systems.
Wind energy: Generated from the kinetic energy of wind using wind turbines.
Hydroelectric power: Generated from the gravitational force of flowing or falling water by utilizing turbines in dams or rivers.
Non-Renewable Energy Sources: These are energy sources that exist in finite quantities and cannot be replenished within a human lifespan. They are formed over geological time scales and are exhaustible. Examples of non-renewable energy sources include:
Fossil fuels: Such as coal, oil, and natural gas, formed from organic matter buried and compressed over millions of years.
Nuclear energy: Derived from the process of nuclear fission, involving the splitting of atomic nuclei.
Sustainable Energy Sources: These are energy sources that are not only renewable but also environmentally friendly and socially and economically viable in the long term. Sustainable energy sources prioritize the well-being of current and future generations by minimizing negative impacts on the environment and promoting social equity. They often involve efficient use of resources and the development of technologies that reduce environmental harm.
An example of a renewable energy source that is not sustainable is biofuel produced from unsustainable agricultural practices. If biofuel production involves clearing vast areas of forests or using large amounts of water, it can lead to deforestation, habitat destruction, water scarcity, or increased greenhouse gas emissions. While the source itself (e.g., crop residue) may be renewable, the overall production process may be unsustainable due to its negative environmental and social consequences.
(b) To calculate the power produced by a wind turbine, we can use the following formula:
Power = 0.5 * (air density) * (blade area) * (wind speed cubed) * (power coefficient)
Given:
Power coefficient (Cp) = 0.4
Blade radius (r) = 50 m
Wind speed (v) = 12 m/s
First, we need to calculate the blade area (A):
Blade area (A) = π * (r^2)
A = π * (50^2) ≈ 7854 m²
Now, we can calculate the power (P):
Power (P) = 0.5 * (air density) * A * (v^3) * Cp
Let's assume the air density is 1.225 kg/m³:
P = 0.5 * 1.225 * 7854 * (12^3) * 0.4
P ≈ 2,657,090 watts or 2.66 MW
Therefore, the wind turbine can produce approximately 2.66 MW of power.
(c) To determine the number of wind turbines needed to supply 100% of the household energy needs of a UK city with 750,000 homes, we need to make some assumptions regarding energy consumption and capacity factors.
Assuming an average household energy consumption of 4,000 kWh per year and a capacity factor of 30% (considering the intermittent nature of wind), we can calculate the total energy demand of the city:
Total energy demand = Number of homes * Energy consumption per home
Total energy demand = 750,000 * 4,000 kWh/year
Total energy demand = 3,000,000,000 kWh/year
Now, let's calculate the total wind power capacity required:
learn more about Energy here:
brainly.com/question/1932868
#SPJ11
Show work when possible! thank you! :)
1. What equation will you use to calculate the acceleration of gravity in your experiment?
2. A ball is dropped from a height of 3.68 m and takes 0.866173 s to reach the floor. Calculate the
free fall acceleration.
3. Two metal balls are dropped from the same height. One ball is two times larger and heavier
than the other ball. How do you expect the free fall acceleration of the larger ball compares to
the acceleration of the smaller one?
1. To calculate the acceleration of gravity in the experiment, the equation used is:
g = 2h / t²
2. The free fall acceleration can be calculated as 8.76 m/s².
3. The free fall acceleration of the larger ball is expected to be the same as the acceleration of the smaller ball.
1. The equation used to calculate the acceleration of gravity in the experiment is derived from the kinematic equation for motion under constant acceleration: h = 0.5gt², where h is the height, g is the acceleration of gravity, and t is the time taken to fall.
By rearranging the equation, we can solve for g: g = 2h / t².
2. - Height (h) = 3.68 m
- Time taken (t) = 0.866173 s
Substituting these values into the equation: g = 2 * 3.68 / (0.866173)².
Simplifying the expression: g = 8.76 m/s².
Therefore, the free fall acceleration is calculated as 8.76 m/s².
3. The acceleration of an object in free fall is solely determined by the gravitational field strength and is independent of the object's mass. Therefore, the larger ball, being two times larger and heavier than the smaller ball, will experience the same acceleration due to gravity.
This principle is known as the equivalence principle, which states that the inertial mass and gravitational mass of an object are equivalent. Consequently, both balls will have the same free fall acceleration, regardless of their size or weight.
To know more about acceleration refer here:
https://brainly.com/question/30660316#
#SPJ11
What must be the electric field between two parallel plates
there is a potential difference of 0.850V when they are placed
1.33m apart?
1.13N/C
0.639N/C
1.56N/C
0.480N/C
The electric field between the two parallel plates when there is a potential difference of 0.850 V and the plates are placed 1.33 m apart is 0.639 N/C.
To calculate the electric field between two parallel plates, we can use the formula:
E=V/d
Where,
E is the electric field,
V is the potential difference between the plates, and
d is the distance between the plates.
According to the question, the potential difference between the two parallel plates is 0.850 V, and the distance between them is 1.33 m. We can substitute these values in the formula above to find the electric field:E = V/d= 0.850 V / 1.33 m= 0.639 N/C
Since the units of the answer are in N/C, we can conclude that the electric field between the two parallel plates when there is a potential difference of 0.850 V and the plates are placed 1.33 m apart is 0.639 N/C. Therefore, the correct option is 0.639N/C.
To know more about electric field:
https://brainly.com/question/12324569
#SPJ11
choose corect one
13. The photoelectric effect is (a) due to the quantum property of light (b) due to the classical theory of light (c) independent of reflecting material (d) due to protons. 14. In quantum theory (a) t
The correct answer for the photoelectric effect is (a) due to the quantum property of light.
The photoelectric effect refers to the phenomenon where electrons are emitted from a material when it is exposed to light or electromagnetic radiation. It was first explained by Albert Einstein in 1905, for which he received the Nobel Prize in Physics
According to the quantum theory of light, light is composed of discrete packets of energy called photons. When photons of sufficient energy interact with a material, they can transfer their energy to the electrons in the material. If the energy of the photons is above a certain threshold, called the work function of the material, the electrons can be completely ejected from the material, resulting in the photoelectric effect.
The classical theory of light, on the other hand, which treats light as a wave, cannot fully explain the observed characteristics of the photoelectric effect. It cannot account for the fact that the emission of electrons depends on the intensity of the light, as well as the frequency of the photons.
The photoelectric effect is also dependent on the properties of the material being illuminated. Different materials have different work functions, which determine the minimum energy required for electron emission. Therefore, the photoelectric effect is not independent of the reflecting material.
So, option A is the correct answer.
To know more about photoelectric effect click on below link :
https://brainly.com/question/9260704#
#SPJ11
An RL circuit is composed of a 12 V battery, a 6.0 H inductor and a 0.050 Ohm resistor. The switch is closed at t=0 The time constant is 2.0 minutes and after the switch has been closed a long time the voltage across the inductor is 12 V. The time constant is 1.2 minutes and after the switch has been closed a long time the voltage across the inductor is zero. The time constant is 2.0 minutes and after the switch has been closed a long time the voltage across the inductor is zero
The time constant is 1.2 minutes and after the switch has been closed a long time the voltage across the inductor is 12 V.
The RL circuit described has a time constant of 1.2 minutes, and after the switch has been closed for a long time, the voltage across the inductor is 12 V.
The time constant (τ) of an RL circuit is determined by the product of the resistance (R) and the inductance (L) and is given by the formula τ = L/R. In this case, the time constant is 1.2 minutes.
When the switch is closed, current begins to flow through the circuit. As time progresses, the current increases and approaches its maximum value, which is determined by the battery voltage and the circuit's total resistance.
In an RL circuit, the voltage across the inductor (V_L) can be calculated using the formula V_L = V_0 * (1 - e^(-t/τ)), where V_0 is the initial voltage across the inductor, t is the time, and e is the base of the natural logarithm.
Given that the voltage across the inductor after a long time is 12 V, we can set V_L equal to 12 V and solve for t to determine the time it takes for the voltage to reach this value. The equation becomes 12 = 12 * (1 - e^(-t/τ)).
By solving this equation, we find that t is equal to approximately 3.57 minutes. Therefore, after the switch has been closed for a long time, the voltage across the inductor in this RL circuit reaches 12 V after approximately 3.57 minutes.
Learn more about resistance from the given link
https://brainly.com/question/29427458
#SPJ11
In a well, water table depth is 500ft, reservoir depth is
4000ft. the average pressure gradient of the formation brine is
0.480psi/ft. what is the reservoir pressure in this well?
The reservoir pressure in the well is approximately 956551.1 psi where the water table depth is 500ft and the reservoir depth is 4000ft.
Given data: Depth of water table = 500 ft
Reservoir depth = 4000 ft
Average pressure gradient of formation brine = 0.480 psi/ft
Formula used: P = Po + ρgh where P = pressure at a certain depth
Po = pressure at the surfaceρ = density of fluid (brine)g = acceleration due to gravity
h = depth of fluid (brine)
Let's calculate the reservoir pressure using the given data and formula.
Pressure at the surface (Po) is equal to atmospheric pressure which is 14.7 psi.ρ = 8.34 lb/gal (density of brine)g = 32.2 ft/s²Using the formula,
P = Po + ρghP = 14.7 + 8.34 × 32.2 × (4000 - 500)P = 14.7 + 8.34 × 32.2 × 3500P = 14.7 + 956536.4P = 956551.1 psi
Therefore, the reservoir pressure in the well is approximately 956551.1 psi.
More on reservoir pressure: https://brainly.com/question/29618842
#SPJ11
A charge and discharge RC circuit is composed of a resistance and a capacitance = 0.1.
d) Identify true or false to the following statements
i) The time constant () of charge and discharge of the capacitor are equal (
ii) The charging and discharging voltage of the capacitor in a time are different (
iii) A capacitor stores electric charge ( )
iv) It is said that the current flows through the capacitor if it is fully charged ( )
i) True. The time constant (τ) of charge and discharge is determined by the product of resistance and capacitance, which is equal in this case.
ii) False. The charging and discharging voltages of the capacitor in an RC circuit are different; during charging, the voltage increases, and during discharging, it decreases.
iii) True. A capacitor stores electric charge by accumulating it on its plates when a voltage is applied.
iv) False. Once a capacitor is fully charged, no current flows through it. It acts as an open circuit, blocking the flow of current.
i) True. The time constant (τ) of a charge and discharge RC circuit is determined by the product of the resistance (R) and capacitance (C), τ = RC. Since the resistance and capacitance values are the same in this case (0.1), the time constant for charging and discharging will be equal.
ii) False. The charging and discharging voltages of the capacitor in a RC circuit are different. During charging, the voltage across the capacitor gradually increases from 0 to the input voltage, while during discharging, the voltage decreases from the initial voltage to 0.
iii) True. A capacitor is an electronic component that stores electric charge. When a voltage is applied across its terminals, the capacitor accumulates charge on its plates, creating an electric field between them.
iv) False. Once a capacitor is fully charged, ideally no current flows through it. In an ideal capacitor, current flows only during the charging and discharging process. Once the capacitor reaches its maximum voltage, the current becomes zero, and the capacitor acts as an open circuit, blocking the flow of current.
Read more on capacitors here: https://brainly.com/question/30529897
#SPJ11
QUESTION 9 The Earth's atmosphere at sea level and under normal conditions has a pressure of 1.01x105 Pa, which is due to the weight of the air above the ground pushing down on it. How much force due to this pressure is exerted on the roof of a building whose dimensions are 196 m long and 17.0m wide? QUESTION 10 Tre gauges for air pressure, as well as most other gauges used in an industrial environment take into account the pressure due to the atmosphere of the Earth. That's why your car gauge reads O before you put it on your tire to check your pressure. This is called gauge pressure The real pressure within a tire or other object containing pressurized stuff would be a combination of what the gauge reads as well at the atmospheric pressure. If a gaugo on a tire reads 24.05 psi, what is the real pressure in the tire in pascals? The atmospheric pressure is 101x105 Pa
The Earth's atmosphere refers to the layer of gases that surrounds the planet. It is a mixture of different gases, including nitrogen (78%), oxygen (21%), argon (0.93%), carbon dioxide, and traces of other gases.
Question 9: To calculate the force exerted on the roof of a building due to atmospheric pressure, we can use the formula:
Force = Pressure x Area
Area of the roof = Length x Width = l x w
Substituting the given values into the formula, we have:
Force = (1.01 x 10^5 Pa) x (196 m x 17.0 m)
Calculating the result:
Force = 1.01 x 10^5 Pa x 3332 m^2
Force ≈ 3.36 x 10^8 N
Therefore, the force exerted on the roof of the building due to atmospheric pressure is approximately 3.36 x 10^8 Newtons.
Question 10: To convert the gauge pressure in psi (pounds per square inch) to Pascals (Pa), we use the following conversion:
1 psi = 6894.76 Pa
To find the real pressure in the tire, we add the gauge pressure to the atmospheric pressure:
Real pressure = Gauge pressure + Atmospheric pressure
Converting the gauge pressure to Pascals:
Gauge pressure in Pa = 24.05 psi x 6894.76 Pa/psi
Calculating the result:
Gauge pressure in Pa ≈ 166110.638 Pa
Now we can find the real pressure:
Real pressure = Gauge pressure in Pa + Atmospheric pressure
Real pressure = 166110.638 Pa + 101 x 10^5 Pa
Calculating the result:
Real pressure ≈ 1026110.638 Pa
Therefore, the real pressure in the tire is approximately 1.03 x 10^6 Pascals.
To know more about Earth's Atmosphere visit:
https://brainly.com/question/32785349
#SPJ11
"Why might a low metalicity environment lead to larger black
holes forming?
In a low metallicity environment, where the abundance of heavy elements like carbon, oxygen, and iron is relatively low, the formation of larger black holes can be influenced by several factors.
First, low metallicity implies that there is less material available to cool and fragment, leading to the formation of massive stars. Massive stars are more likely to undergo core-collapse supernovae, leaving behind massive stellar remnants that can potentially evolve into black holes.Secondly, metal-rich environments can enhance the efficiency of mass loss through stellar winds, reducing the mass available for black hole formation. In contrast, low metallicity environments have weaker winds, allowing more mass to be retained by the stars, contributing to the formation of larger black holes.Furthermore, low metallicity environments also have lower opacity, which facilitates the accretion of mass onto the forming black holes. This increased accretion can lead to the growth of black holes to larger sizes over time. Overall, the combination of these factors in a low metallicity environment can favor the formation and growth of larger black holes.Learn more about the black holes:
brainly.com/question/6037502
#SPJ11
In the figure, two concentric circular loops of wire carrying current in the same direction lie in the same plane. Loop 1 has radius 1.30 cm and carries 4.40 mA. Loop 2 has radius 2.30 cm and carries 6.00 mA. Loop 2 is to be rotated about a diameter while the net magnetic field B→B→ set up by the two loops at their common center is measured. Through what angle must loop 2 be rotated so that the magnitude of the net field is 93.0 nT? >1 2
Loop 2 must be rotated by approximately 10.3 degrees in order to achieve a net magnetic field magnitude of 93.0 nT at the common center of the loops.
To determine the angle of rotation, we need to consider the magnetic fields produced by each loop at their common center. The magnetic field produced by a current-carrying loop at its center is given by the formula:
B = (μ0 * I * A) / (2 * R)
where μ0 is the permeability of free space (4π × 10^-7 T•m/A), I is the current, A is the area of the loop, and R is the radius of the loop.
The net magnetic field at the common center is the vector sum of the magnetic fields produced by each loop. We can calculate the net magnetic field magnitude using the formula:
Bnet = √(B1^2 + B2^2 + 2 * B1 * B2 * cosθ)
where B1 and B2 are the magnitudes of the magnetic fields produced by loops 1 and 2, respectively, and θ is the angle of rotation of loop 2.
Substituting the given values, we have:
Bnet = √((4π × 10^-7 T•m/A * 4.40 × 10^-3 A * π * (0.013 m)^2 / (2 * 0.013 m))^2 + (4π × 10^-7 T•m/A * 6.00 × 10^-3 A * π * (0.023 m)^2 / (2 * 0.023 m))^2 + 2 * 4π × 10^-7 T•m/A * 4.40 × 10^-3 A * 6.00 × 10^-3 A * π * (0.013 m) * π * (0.023 m) * cosθ)
Simplifying the equation and solving for θ, we find:
θ ≈ acos((Bnet^2 - B1^2 - B2^2) / (2 * B1 * B2))
Substituting the given values and the net magnetic field magnitude of 93.0 nT (93.0 × 10^-9 T), we can calculate the angle of rotation:
θ ≈ acos((93.0 × 10^-9 T^2 - (4π × 10^-7 T•m/A * 4.40 × 10^-3 A * π * (0.013 m)^2 / (2 * 0.013 m))^2 - (4π × 10^-7 T•m/A * 6.00 × 10^-3 A * π * (0.023 m)^2 / (2 * 0.023 m))^2) / (2 * (4π × 10^-7 T•m/A * 4.40 × 10^-3 A * π * (0.013 m) * 4π × 10^-7 T•m/A * 6.00 × 10^-3 A * π * (0.023 m)))
Calculating the value, we find:
θ ≈ 10.3 degrees
Therefore, loop 2 must be rotated by approximately 10.3 degrees in order to achieve a net magnetic field magnitude of 93.0 nT at the common center of the loops.
Learn more about magnetic field here; brainly.com/question/30331791
#SPJ11
At a point a distance r=1.10 m from the origin on the positive x-axis, find the magnitude and direction of the magnetic field. (a) magnitude of the magnetic field (in T ) T (b) direction of the magnetic field +x-direction −x-direction +y-direction −y-direction +z-direction -z-direction At a point the same distance from the origin on the negative y-axis, find the magnitude and direction of the magnetic field. (c) magnitude of the magnetic field (in T ) At a point a distance r=1.10 m from the origin on the positive x-axis, find the magnitude and direction of the magnetic field. (a) magnitude of the magnetic field (in T ) T (b) direction of the magnetic field +x-direction −x-direction +y-direction −y-direction +z-direction −z-direction At a point the same distance from the origin on the negative y-axis, find the magnitude and direction of the magnetic field. (c) magnitude of the magnetic field (in T) T (d) direction of the magnetic field +x-direction
(a) The magnitude of the magnetic field at a point a distance r=1.10 m from the origin on the positive x-axis is 0.063 T.
(b) The direction of the magnetic field is +x-direction.
(c) The magnitude of the magnetic field at a point the same distance from the origin on the negative y-axis is 0.063 T.
(d) The direction of the magnetic field is −y-direction.
The magnetic field at a point due to a current-carrying wire is given by the Biot-Savart law:
B = µo I / 2πr sinθ
where µo is the permeability of free space, I is the current in the wire, r is the distance from the wire to the point, and θ is the angle between the wire and the line connecting the wire to the point.
In this case, the current is flowing in the +x-direction, the point is on the positive x-axis, and the distance from the wire to the point is r=1.10 m. Therefore, the angle θ is 0 degrees.
B = µo I / 2πr sinθ = 4π × 10-7 T⋅m/A × 1 A / 2π × 1.10 m × sin(0°) = 0.063 T
Therefore, the magnitude of the magnetic field at the point is 0.063 T. The direction of the magnetic field is +x-direction, because the current is flowing in the +x-direction and the angle θ is 0 degrees.
The same calculation can be done for the point on the negative y-axis. The only difference is that the angle θ is now 90 degrees. Therefore, the magnitude of the magnetic field at the point is still 0.063 T, but the direction is now −y-direction.
To learn more about magnetic field here brainly.com/question/23096032
#SPJ11
Choose the correct statement regarding optical instruments such as eyeglasses. A near-sighted person has trouble focusing on distant objects and wears glasses that are thinner on the edges and thicker in the middle. A person with prescription of -3.1 diopters is far-sighted. A near-sighted person has a near-point point distance that is farther than usual. A person with prescription of -3.1 diopters is near-sighted. A near-sighted person has trouble focusing on distant objects and wears glasses with converging lenses.
The correct statement regarding optical instruments such as eyeglasses is that a near-sighted person has trouble focusing on distant objects and wears glasses with diverging lenses. The correct option is - A near-sighted person has trouble focusing on distant objects and wears glasses with converging lenses.
Nearsightedness is a condition in which the patient is unable to see distant objects clearly but can see nearby objects. In individuals with nearsightedness, light rays entering the eye are focused incorrectly.
The eyeball in nearsighted individuals is somewhat longer than normal or has a cornea that is too steep. As a result, light rays converge in front of the retina rather than on it, causing distant objects to appear blurred.
Eyeglasses are an optical instrument that helps people who have vision problems see more clearly. Eyeglasses have lenses that compensate for refractive errors, which are responsible for a variety of visual problems.
Eyeglasses are essential tools for people with refractive problems like astigmatism, myopia, hyperopia, or presbyopia.
A near-sighted person requires eyeglasses with diverging lenses. Diverging lenses have a negative power and are concave.
As a result, they spread out light rays that enter the eye and allow the image to be focused properly on the retina.
So, the correct statement is - A near-sighted person has trouble focusing on distant objects and wears glasses with converging lenses.
Learn more about eyeglasses here:
https://brainly.com/question/31868298
#SPJ11
In the figure(Figure 1) the coefficient of static friction between mass mA and the table is 0.43, whereas the coefficient of kinetic friction is 0.33.What value of mAmA will keep the system moving at constant speed?
To keep the system moving at a constant speed, the applied force must balance the frictional forces acting on the system.
The maximum static frictional force is given by the equation F_static = μ_static * N, where μ_static is the coefficient of static friction and N is the normal force. The kinetic frictional force is given by F_kinetic = μ_kinetic * N. Since the system is moving at a constant speed, the applied force must equal the kinetic frictional force. Therefore, to find the value of mA that keeps the system moving at a constant speed, we can set the applied force equal to the kinetic frictional force and solve for mass mA.
F_applied = F_kinetic
mA * g = μ_kinetic * (mA + mB) * g
By substituting the given values for μ_kinetic and solving for mass mA, we can find the value that keeps the system moving at a constant speed.
Learn more about speed here:
brainly.com/question/17661499
#SPJ11
What is the dose in rem for each of the following? (a) a 4.39 rad x-ray rem (b) 0.250 rad of fast neutron exposure to the eye rem (c) 0.160 rad of exposure rem
The dose in rem for each of the following is:(a) 4.39 rem(b) 5.0 rem(c) 0.160 rem. The rem is the traditional unit of dose equivalent.
It is the product of the absorbed dose, which is the amount of energy deposited in a tissue or object by radiation, and the quality factor, which accounts for the biological effects of the specific type of radiation.A rem is equal to 0.01 sieverts, the unit of measure in the International System of Units (SI). The relationship between the two is based on the biological effect of radiation on tissue. Therefore:
Rem = rad × quality factor
(a) For a 4.39 rad x-ray, the dose in rem is equal to 4.39 rad × 1 rem/rad = 4.39 rem
(b) For 0.250 rad of fast neutron exposure to the eye, the dose in rem is 0.250 rad × 20 rem/rad = 5.0 rem
(c) For 0.160 rad of exposure, the dose in rem is equal to 0.160 rad × 1 rem/rad = 0.160 rem
The dose in rem for each of the following is:(a) 4.39 rem(b) 5.0 rem(c) 0.160 rem.
To know more about International System of Units visit-
brainly.com/question/30404877
#SPJ11
Example 8 A planet orbits a star in a year of length 4.37 x 10's, in a nearly circular orbit of radius 2.94 x 1011 m. With respect to the star, determine (a) the angular speed of the planet, (b) the tangential speed of the planet, and (c) the magnitude of the planet's centripetal acceleration. (a) Number Units m m (b) Number Units m/s (c) Number Units m/ s2
(a) The angular speed of the planet is approximately 0.144 rad/s.
(b) The tangential speed of the planet is approximately 1.27 x 10⁴ m/s.
(c) The magnitude of the planet's centripetal acceleration is approximately 5.50 x 10⁻³ m/s².
(a) The angular speed of an object moving in a circular path is given by the equation ω = 2π/T, where ω represents the angular speed and T is the time period. In this case, the time period is given as 4.37 x 10⁶ s, so substituting the values, we have ω = 2π/(4.37 x 10⁶) ≈ 0.144 rad/s.
(b) The tangential speed of the planet can be calculated using the formula v = ωr, where v represents the tangential speed and r is the radius of the orbit. Substituting the given values, we get v = (0.144 rad/s) × (2.94 x 10¹¹ m) ≈ 1.27 x 10⁴ m/s.
(c) The centripetal acceleration of an object moving in a circular path is given by the equation a = ω²r. Substituting the values, we get a = (0.144 rad/s)² × (2.94 x 10¹¹ m) ≈ 5.50 x 10⁻³ m/s².
learn more about angular speed here:
https://brainly.com/question/30402548
#SPJ11
An alien pilot of an intergalactic spaceship is traveling at 0.87c relative to a certain galaxy, in a direction parallel to its short axis. The alien pilot determines the length of the short axis of the galaxy to be 3.0 × 10^17 km. What would the length of this axis be as measured by an observer living on a planet within the galaxy?
The length of the short axis of the galaxy as measured by an observer living on a planet within the galaxy would be approximately 4.1 × 10^17 km.
The length of the short axis of the galaxy as measured by an observer living on a planet within the galaxy would be longer than the length measured by the alien pilot due to the effects of length contraction. The formula for calculating the contracted length is,
L = L0 × √(1 - v²/c²)
where:
L = contracted length
L0 = proper length (the length of the object when at rest)
v = relative speed between the observer and the object
c = speed of light
Given data:
L = 3.0 × 10¹⁷ km
v = 0.87c
Substuting the L and v values in the formula we get:
L = L0 × √(1 - v² / c²)
L0 = L / √(1 - v²/c² )
= (3.0 × 10¹⁷ km) / √(1 - (0.87c)²/c²)
= (3.0 × 10¹⁷km) /√(1 - 0.87²)
= 4.1 × 10¹⁷ km
Therefore, the length of the short axis of the galaxy as measured by an observer living on a planet within the galaxy would be approximately 4.1 × 10^17 km.
To learn more about length contraction:
https://brainly.com/question/17407131
#SPJ4
2. Two closeby speakers produce sound waves. One of the speakers vibrates at 400 Hz. What would be the frequency of the other speaker, which produces 10 Hz of beats? A. 10 Hz B. 390 Hz C. 410 Hz
Summary:
The frequency of the other speaker would be 390 Hz. When two closeby speakers produce sound waves, a phenomenon known as beats can occur. Beats are the periodic variations in the intensity or loudness of sound that result from the interference of two waves with slightly different frequencies.
Explanation:
In this case, if one speaker vibrates at 400 Hz and the beats have a frequency of 10 Hz, it means that the frequency of the other speaker is slightly different. The beat frequency is the difference between the frequencies of the two speakers. So, by subtracting the beat frequency of 10 Hz from the frequency of one speaker (400 Hz), we find that the frequency of the other speaker is 390 Hz.
To understand this concept further, let's delve into the explanation. When two sound waves with slightly different frequencies interact, they undergo constructive and destructive interference, resulting in a periodic variation in the amplitude of the resulting wave. This variation is what we perceive as beats. The beat frequency is equal to the absolute difference between the frequencies of the two sound waves. In this case, the given speaker has a frequency of 400 Hz, and the beat frequency is 10 Hz. By subtracting the beat frequency from the frequency of the given speaker (400 Hz - 10 Hz), we find that the frequency of the other speaker is 390 Hz. This frequency creates the interference pattern that produces the 10 Hz beat frequency when combined with the 400 Hz wave. Therefore, the correct answer is B. 390 Hz.
Learn more about Periodic Variations here brainly.com/question/15295474
#SPJ11