The actual length of the line 469.449 ft, if one assumes the modulus of elasticity of steel to be 29,000,000 psi.
What is elasticity of metal?A metal's elasticity is defined as the rate at which a specific metal sample can change in size and shape in response to a variety of stress and strain forces as well as other externally varying factors. The measured level of ductility of a metal can also be referred to as elasticity.
Due to the increased surface area that is exposed when elongated, metals that are subjected to repeated applications of force to cause elastic expansion are more vulnerable to stress corrosion, cracking, and crevice corrosion.
When a metal deforms elastically, the process is reversible, allowing the metal to revert to its initial shape.
Learn more about elasticity
https://brainly.com/question/14017540
#SPJ4
ipcc not incorporating the impact of climate change on hazards such as heat waves and flooding will potentially significantly underestimate the risks presented by these hazards
The most important thing humans can do to assist nature in battling climate change is to safeguard the world's natural environments, which hold billions of tons of this "living carbon."
However, the conclusion is that regional climate changes, particularly temperature rises, are having an impact on natural systems all over the world, and that these temperature increases are very likely caused by anthropogenic emissions of greenhouse gases. By the end of this century, extreme sea level occurrences that formerly happened once every 100 years could occur annually. The loss of seasonal snow cover, glacier and ice sheet melting, and summer Arctic Sea ice will all be accelerated by further warming.
Learn more about system here-
https://brainly.com/question/27162243
#SPJ4
determine the 0.2% offset yield strength from the stress-strain data. the sample is cylindrical with a radius of 1.25 mm.
By building a parallel line offset from the linear stress-strain line by 0.002 strain, the 0.2% offset yield strength is computed.
Because the yield strength of steel, according to ASTM, is 0.2% permanent strain (offset). This definition serves as a good "rule of thumb" for the majority of steels and typically equates to a 0.5% total strain. The predetermined amount of permanent strain is set along the strain axis of the graph, to the right of the origin, in order to determine yield strength. Figure 5 designates it as Point. Point (D) is crossed by a straight line that has the same slope as the first part of the stress-strain curve.
Learn more about stress here-
https://brainly.com/question/17252580
#SPJ4
the technician connects one test lead to the chassis ground and the other to the door chime negative connection. then, the technician performs a voltage drop test on the ground side circuit to the door chime module and finds that the ground side circuit voltage has a 3v drop reading. what is the next step?
The next step of technician is to take a look at the ground wire that runs from the door chime module connector to the chassis ground.
An electrical connection between various metallic components of a machine is ensured by a chassis ground, which connects them all. A couple such examples include automobiles and electrical devices. As with lightning protection for high voltage power systems, chassis grounding provides the same function for electronics. To avoid damaging or interrupting circuit functionality, it is specifically necessary to direct undesired and potentially harmful current away from system parts and components. An electrical device's metal housing serves as the chassis ground, which is a site where ground is collected. To prevent electrical shock, a chassis ground can be utilized for grounding and shielding. Using a strong ground wire or cable, ground the engine block to the frame, ensuring sure that the connections are metal to metal, clean, and secure.
Learn more about chassis ground here:
https://brainly.com/question/4244425
#SPJ4
technician a says that a transaxle first-gear ratio of 3.5:1 means input torque is increased by 3.5 times. technician b says that a transaxle first-gear ratio of 3.5:1 means input speed is increased by 3.5 times. which technician is correct?
The technician A is right. When the transaxle's first gear is 3.5:1, the input torque is multiplied by 3.5. The output torque is thus 3.5 times greater than the input torque. The first-gear ratio of the transaxle has no impact on the input speed.
What is a torque?
The force that can force an object to spin along an axis is measured as torque. In linear kinematics, force is what drives an object's acceleration. Similar to this, an angular acceleration is brought on by torque. As a result, torque can be thought of as the rotational counterpart to force.
To know more about torque
https://brainly.com/question/17512177
#SPJ4
Which statement about the filtering result of the following ACL is true?
Router(config-ext-nacl)# permit tcp 192.168.1.0 0.0.0.255 host 192.168.100.1 eq 80
Router(config-ext-nacl)# deny tcp any host 192.168.100.1 eq 80
If you want to prevent traffic from entering the internal server network, use the command ip access-list 6 deny 192.168.1.00.0.0.255.
How does the router's ACL filter work?A set of rules known as a "Access Control List" (ACL) governs how any traffic passing through routers is allowed, permitted, or denied. By filtering and managing the traffic flow between routers, it functions at layer 3 to ensure security.According to the source IP address, destination IP address, and port numbers, packet filtering occurs in the Extended access list. Services will either be allowed or blocked according to an extended access list. From 100 to 199, and 2000 to 2699, are the extended ACL ranges that are produced.If you want to prevent traffic from entering the internal server network, use the command ip access-list 6 deny 192.168.1.00.0.0.255.To learn more about "Access Control List" (ACL) refer to:
https://brainly.com/question/13198620
#SPJ4
while examining a heavy, flat steel plate bolted to the oil pan rails and main bearing caps, technician a suggests it is used to stiffen the crankcase to reduce torsional twisting. technician b says the plate is used to prevent oil from splashing up onto the cylinder walls and causing high oil consumption. who is correct?
Technician a is correct because that he says claims that it is utilized to strengthen the crankcase in order to prevent torsional twisting.
Engine heat ultimately determines what temperature the oil reaches and is the most common cause of high oil pressure. Oil pressure can also increase due to malfunctioning engine parts. Low oil level is the most frequent and simplest to fix reason for low pressure. While regular oil changes are important, it's also crucial to regularly check your motor oil level and top it off as needed in between oil changes. A beam will twist when a torque is applied, and this is known as torsional twisting. It is applied methodically to screws, nuts, axles, drive shafts, etc., and is also produced more randomly under service conditions in car bodies, boats, airplane fuselages, bridges, springs, and many other structures and components.
Learn more about torsional twisting here:
https://brainly.com/question/14887736
#SPJ4
PSPICE 6.23 MULTISIM Assume that the initial energy stored in the inductors of Figs. P6.23(a) and (b) is zero. Find the equiva- lent inductance with respect to the terminals a, b. Figure P6.23 (a) 12 mH 24 mH 10 mH 520 mH 30 mH 15 mH 9 mH3 8 mH (b) 25 uH 18 uH 20 uH 60 uH 30 H 1) UH 312 pH 15 pH 38 pH
A mass moving at a certain speed is comparable to an inductor conducting current. In other words, a coil carrying current stores energy
In its magnetic field, which equals 1/2 Li2, just like a moving mass has kinetic energy = 1/2 mv2. Actually, the magnetic field produced by the current passing through the inductor is where this energy is kept. The energy is stored without being lost in a pure inductor, where it is released back into the circuit when the inductor's magnetic field collapses and the current through it is ramped down. The charge Q and voltage V between the capacitor plates are related to the energy U C U C stored in a capacitor because it is electrostatic potential energy.
Learn more about speed here-
https://brainly.com/question/28988558
#SPJ4
Which of the following is shared among threads? Select all that apply. file descriptors registers stack memory virtual address space
Every thread have its own stack, register, and PC, so only address space that is shared by all thread for a single process.
Why threads are important?The use of threads has a number of advantages. A thread is more effective. For a new thread, the operating system does not need to construct a new memory map (as it does for a process). In order to monitor the status of open files and increase reference counts on open file descriptors, it is not necessary to allocate new structures.Additionally, threading makes some programming styles simple. Although it is true that shared memory among threads increases the risk of problems, shared memory also makes it simple to communicate data among threads. All threads in a process can read from and write to the same global and static variables.To learn more about thread, refer to
https://brainly.com/question/28271701
#SPJ4
6 In the figure shown, shaft A, made of AISI 1010 hot-rolled steel, is welded to a fixed support and
is subjected to loading by equal and opposite forces F via shaft B. A theoretical stress concentration
Kts of 1.6 is induced by the 3 mm fillet. The length of shaft A from the fixed support to the connection
at shaft B is 1 m. The load F cycles from 0.5 to 2 kN.
a) For shaft A, find the factor of safety for infinite life using the modified Goodman fatigue failure
criterion.
b) Repeat part(a) using Gerber fatigue failure criterion.
Answer:
Explanation:
Calculate the factor of safety for infinite life using modified Goodman fatigue failure.
Tmax =16KfsTmax /πd^3
HB =200, r=3 mm, qs = 1
Kfs=1+qs(Kts-1)= 1+1(1.6-1) = 1.6
Calculate the maximum and minimum torque.
Tmax=2000(0.05) = 100 N. m
Tmin=500 /2000 (100)
Tmin= 25 N.m
Calculate the maximum and minimum shear stress on the shaft.
Tmax= 16(1.6)(100) (10-6) /π(0.02)3 = 101.9 MPa Tmax
Tmin=500 /2000 (101.9)
Tmin=7.4 N. m
Kb=(7.4/7.62) ^-0.107
Kb=0.59
Se=0.917(1.003)(0.59)(161.3) = 87.5 MPa
nf = 1/ (Ta/Se)+(Tm/Ssu)
=1 /(38.22/87.5)+(63.68/214.4)
= 1.36
b)
Calculate the factor of safety for infinite life using modified Gerber fatigue failure.
nf=1/2 (Ssu/Tm) ^2 Ta/Se [ -1+square root of 1+
(2Tm Se/Ssu Ta) ^2]
= 1/2 (214.4/63.68) ^2 (38.22/87.6) {-1+square root of 1+ [2(63.68) (87.5) /214.4 (38.22) ]^2
=1.70
= 25.46 MPa
Calculate the mean stress.
Tm = 1/2 (101.9+25.46)
= 63.68 MPa
Calculate the average stress.
Ta= 1/2
Ta= 1/2 (101.9-25.46)
=38.22 MPa
Ssu=0.67Sut
= 0.67(320)
= 214.4 MPa
Ssy = 0.577Sy
= 0.577(180)
= 103.9 MPa
Se = 0.504(320)
= 161.3 MPa
ka =57.7(320)-0.718
= 0.917
de = 0.370(20)
02-series deep-groove ball bearing is considered as an application with the inner ring rotating, with a design life of 25 kh at a speed of 350 rev/min. the radial load is 2.5 kn and an application factor of 1.2 is appropriate. the reliability goal is 0.90. find the catalog rating c10 with which to enter a bearing table and select an appropriate size bearing.
The reliability goal is 0.90 is reached with given perameter and chosen bearing is correct the C10 catalogue rating would be 14.
R=exp{-{525(3/25.50³-0.02/4.439}^1.483}
=exp{-{0.98/4.439}^1.483}
=exp(-0.106)
=0.919
So, the chosen bearing is correct.
A bearing is a part of a machine that reduces friction between moving parts and restricts relative movement to only that motion that is intended. A fixed axis rotation or free linear motion of the moving part are two examples of possible bearing designs. By controlling the normal force vectors acting on the moving parts, it may also be used to stop movement. To enable the desired motion, the majority of bearings reduce friction. Bearings can be divided into many different groups depending on the type of operation, the motions allowed, or the direction of the loads (forces) applied to the components.
Learn more about bearing here:
https://brainly.com/question/27914967
#SPJ4
water (10 oc) flows with a speed of 2 m/s through a horizontal run of pvc pipe. the length of the pipe is 50 m, and the pipe is schedule 40 with a nominal diameter of 2.5 inch. calculate: a) the pressure drop in kpa b) the head loss in meters c) the power in watts needed to overcome the head loss
The pipe is schedule 40 and has a nominal diameter of 2.5 inches. It is 50 meters long. Then pressure drop is 29.1kpa,Head loss is 2.967m and power is 176.986 watt.
a)Pressure drop = 32μVL/D²
=32*1.307*10⁻³*2*50/0.0119882
=29102.6 pascal
=29.1 Kpa
b)Head loss=p1-p2/pg=29.1*10³/999.7*9.81
=2.967 m
c)power=(p1-P2)q
=29.1*10³*6.082*10⁻³
Power =176.986 watt //watt is the unit of power
The difference in total pressure between two points on a network used to transport fluids is known as a pressure drop. When frictional forces acting on a fluid as it flows through the tube, brought on by the resistance to flow, occur, a pressure drop happens.
Learn more about pressure drop here:
https://brainly.com/question/15851784
#SPJ4
The automatic antenna tuner on the ft-dx10 is designed to ensure what ohm antenna impedence is presented?.
At amateur operating frequencies, the FTDX10 is designed for 50 Ohm resistive impedance.
What is meant by Impedance?Impedance is the sum of resistance and reactance. It was defined as anything that can obstructs the flow of electrons within the electrical circuit. As a result, it influences current generation in the electrical circuit. It could be found in all the possible circuit components and across all possible electrical circuits. Impedance is represented mathematically by the letter Z and has the unit ohm. It's a mix of resistance and reactance.
Z stands for impedance, which is an expression of the resistance to alternating and/or direct electric current that an electronic component, circuit, or system offers. Resistance and reactance are two independent scalar (one-dimensional) phenomena that make up the vector (two-dimensional) quantity known as impedance.
To learn more about Impedance refer to :
https://brainly.com/question/13134405
#SPJ4
when a given op-amp has a common-mode input of 1 v, the output of the device is 100 mv. when the device has a differential input of 2 mv, the output of the device is 10 v. what is the cmrr of the device'? 50,000,000 : 1 50,000 : 1 1000 : 1 5 : 1
The CMRR the device is 5 : 1. The CMRR can be meant as ratio between common model gain and differential model gain.
CMRR refers to the ratio of the common-mode gain with differential-mode gain. The example of CMRR happens when a differential input change of Y volts produces a change of 1 V at the output, and a common-mode change of X volts produces a similar change of 1 V, then the CMRR is X/Y.
Assume a common-mode input of 1 v, the output of the device is 100 mv is Y
Common mode gain = Vout/Vin
Common mode gain = 0.01/1 = 0.01
Differential mode gain = 1
Then,
CMRR = Common mode gain/ Differential mode gain
CMRR = 0.01/1 = 0.01
Assume when the device has a differential input of 2 mv, the output of the device is 10 v is Y
Common mode gain = Vout/Vin
Common mode gain = 10/2
Common mode gain = 5
Differential mode gain = 10/2-1 = 10
Then,
CMRR = Common mode gain/ Differential mode gain
CMRR = 5/10 = 0.5
Hence, ratio of the CMRR in device is
CMRR = 0.5/0.1 = 5 : 1
Learn more about the CMRR, here https://brainly.com/question/16807653
#SPJ4
Briefly explain how each of the following influences the tensile modulus of a semicrystalline polymer and why: (a) molecular weight (b) degree of crystallinity (c) deformation by drawing (d) annealing of an undeformed material (e) annealing of a drawn material
The molecular weight Increases, degree of crystallinity Decreases, deformation by drawing Increases, annealing of an undeformed material Increases, annealing of a drawn material Increases.
Molecular Weight: As the polymer's molecular weight rises, it does as well. Degree of crystallinity: As the degree of crystallinity of a semi-crystalline polymer grows, so does its tensile strength. Drawing-induced deformation: Drawing-induced deformation of a polymer results in a finely oriented chain structure, and the increased secondary interchain bonding structure increases the polymer's tensile strength. The tensile strength of the material also increases as a result of annealing an undeformed substance.
Learn more about tensile here-
https://brainly.com/question/13260444
#SPJ4
A uniform rod BC of mass 4 kg is connected to a collar A by a 250-mm cord AB. Neglecting the mass of the collar and cord, determine (a) the smallest constant acceleration aA for which the cord and the rod lie in a straight line, (b) the corresponding tension in the cord. 250 mm 400 mm 350 mm
(a) The smallest constant acceleration aA for which the cord and the rod lie in a straight line is, a[tex]_A[/tex] = 4.09 m/sec².
(b) The corresponding tension in the cord is, T = 42.5 N.
What is tension?The force transmitted through a rope, string, or wire when pulled by forces acting from opposite sides is referred to as tension. The tension force is applied along the entire length of the wire and exerts an equal amount of force on the bodies at each end.
Every physical object that comes into contact with another one applies some sort of force. Depending on the type of object, these contact forces have different names. You can refer to a force as tension if a rope, cable, or chain is one of the objects it is pulling on.
Ropes and cables are useful for exerting forces because they effectively transfer a force over a limited distance (e.g. the rope length). Because ropes cannot effectively push, tension must be considered the pulling force.
Learn more about tension
https://brainly.com/question/24994188
#SPJ4
a 220-v-rms, 60 hz, 3-phase y-connected induction motor draws 31.87 a at a power factor of 75% lagging. for all three phases, the total stator copper losses are 400 w, and the total copper losses are 150 w. the rotational losses are 500 w
It is possible to change the slip and speed at which the maximum torque occurs if the rotor resistance is raised in some way.
In the case of slip ring or wound rotor type motors, this can be accomplished by adding external resistance to the rotor circuit. This occurs when the rotor conductors are shorted-circuited and there is a transformer action between the stator winding and the rotor winding. The rotor experiences a strong current flow as a result. The starting torque is also impacted if the applied starting voltage is decreased in order to reduce this high starting current.
Learn more about Resistance here-
https://brainly.com/question/18238576
#SPJ4
a 220-v-rms, 60 hz, 3-phase y-connected induction motor draws 31.87 a at a power factor of 75% lagging. for all three phases, the total stator copper losses are 400 w, and the total copper losses are 150 w. the rotational losses are 500 w
If the rotor resistance is increased in any way, it is possible to alter the slip and speed at which the greatest torque occurs.
This may be done in the case of slip ring or wound rotor type motors, right?via rotor circuit's addition of external resistance. When the rotor conductors are shorted-circuit, a transformer-like effect between the stator winding and the rotor winding takes place.
As a result, a powerful current flow is felt in the rotor. If the applied beginning voltage is lowered in an effort to lower this high starting current, the starting torque is also affected.
To know more about induction motor visit:-
https://brainly.com/question/28852537
#SPJ4
historically, the average grade in chem 1015 is a b-/c . in order for an average student to earn an average grade, the average student would be expected to spend an average of 3 hour(s) a week on the course.
Students who specialize in a major field are better equipped to conduct in-depth research, analyze critically, and use discriminating judgment.
It makes the student ready for more difficult work, graduate school, or the job market right away. This concentration on the academic curriculum does not mean that other aspects of university life, including as social and athletic activities, public speaking and dramatic arts, music, art, public affairs, or other programs, did not contribute significantly to a student's personality development. The intended outcome of these degree programs is not a person who fits into society as it is or perceives their own vocation as being limited to the realm of the regular job, but rather a person who has been intellectually enhanced.
Learn more about concentration here-
https://brainly.com/question/27602071
#SPJ4
a vehicle is found to have multiple oil leaks. technician a says that all of the oil leaks should be repair. technician b says the pcv system should be tested first. who is correct?
Technician b says the pcv system should be tested first is correct.
What is pcv system?Vaccine Knowledge | PCV (Pneumococcal Conjugate Vaccine). MenB vaccination (Meningococcal B Vaccine)
Poor fuel economy is one of the indications of a faulty PCV valve. The precise ratio of the air and fuel mixture, which is necessary for proper combustion, will be thrown off by a broken PCV valve.
While not all vehicles have one, the majority do. If your vehicle has one, check the PCV valve (shown in Figure 8-5) to make sure it isn't blocked with sludge from impurities in the exhaust fumes or stuck in the wide-open position if your engine has been idling unevenly or if a malfunction indicator light comes on.
To learn more about pcv system refer to:
https://brainly.com/question/13812760
#SPJ4
a heating element operates on 115 v. if it has a resistance of 15.4 ohms, what current, in amps, does it draw?
The current is 7.46A. A stream of charged particles, such as electrons or ions, travelling through an electrical conductor or a vacuum is known as an electric current.
How to calculate current?Electric currents are streams of electrically charged particles, such as electrons or ions, moving through a conductor or a void. It is calculated as the net rate of electric charge flowing through a surface or into a control volume.Electric currents generate magnetic fields, which are used in motors, generators, inductors, and transformers. In typical conductors, they cause Joule heating, which ignites incandescent light bulbs. To transfer information via communications, time-varying currents produce electromagnetic waves.Current is obtained by merely dividing the magnitude of a charge by the measurement duration. Current can be calculated using the equation I = Q t, where I denotes current, Q denotes charge, and t denotes time.Given value
Voltage = 115v
Resistance = 15.4 ohms
Equation is Current = V / R
I = V / R
= 115V / 15.4Ω = 7.467532A
The current is 7.467532 amps
To learn more about current refer :
https://brainly.com/question/24858512
#SPJ4
use channel 1 of your oscilloscope to monitor the voltage vc across the capac- itor while using channel 2 to monitor the voltage vr across the resistor.
There are two ways to detect current using an oscilloscope, even though the majority of them can only directly measure voltage.
What is oscilloscope?
An oscillograph, which was the previous name for an oscilloscope, is a device that graphically displays electrical signals and illustrates how those signals change over time.
Through a sensor connection, a device that generates an electrical signal in response to physical stimuli like sound, light, and heat, it is able to measure these signals. A microphone, for instance, is a sensor that turns sound into an electrical signal.
Shunt resistors can be used as feedback devices in some power supply designs; measure the voltage dropped across one. An oscilloscope can be used to measure a time constant to determine the real capacitance of a device or the amount of dispersed capacitance in an electrical system.
From one peak to the next, count the horizontal divisions of your oscillating signal (i.e., peak to peak). The period of the signal is then calculated by multiplying the number of horizontal divisions by the time or division. The frequency of the signal can be calculated using the following formula: frequency=1/period.
Learn more about oscilloscope
https://brainly.com/question/29673956
#SPJ4
It's the law. Under New York law, you can get a citation for riding your bike while listening to music using headphones or earbuds in both ears. It is lawful, however, to listen to music with only one earbud keeping the other ear free.
Sensory deprivation. One of the main ways that people alert each other to danger on the road is through sound. Whether it's honking, yelling or ringing a bicycle bell, you're less likely to hear any of these warnings if you're listening to music putting you at higher risk of an accident.
Decreased attention. The more stimuli you have to contend with, the more difficult it is to dedicate your full attention to one particular task. If you get caught up in a song or story you're listening to while cycling, it can increase your distractibility which could have disastrous consequences.
The majority of cycling-related accidents involve a cyclist and a motor vehicle. Not surprisingly, the injuries a cyclist suffers in such collisions tend to be disproportionately serious and often fatal. Therefore, if you're cycling in traffic, foregoing the headphones can prove to be a life-saving decision.
Answer:s
Explanation:s
It's the law. Under New York law, you can get a citation for riding your bike while listening to music using headphones or earbuds in both ears. It is lawful, however, to listen to music with only one earbud keeping the other ear free.
Sensory deprivation. One of the main ways that people alert each other to danger on the road is through sound. Whether it's honking, yelling or ringing a bicycle bell, you're less likely to hear any of these warnings if you're listening to music putting you at higher risk of an accident.
Decreased attention. The more stimuli you have to contend with, the more difficult it is to dedicate your full attention to one particular task. If you get caught up in a song or story you're listening to while cycling, it can increase your distractibility which could have disastrous consequences.
The majority of cycling-related accidents involve a cyclist and a motor vehicle. Not surprisingly, the injuries a cyclist suffers in such collisions tend to be disproportionately serious and often fatal. Therefore, if you're cycling in traffic, foregoing the headphones can prove to be a life-saving decision.
how can the elevation of an intermediate turning point be calculated from the usual note format of differential levels?
By deducting the foresight rod reading from the instrument's height, the elevation is computed. The elevation reading of a site with unknown elevation is called a foresight.
How do you calculate elevation using differential leveling?If you are aware of A's elevation (E(A)), you can use the formula BS - FS + E to get B's elevation (E(B)) (A).
However, the instrument's height or the elevation of the line of sight directed from the level is determined by BS + E(A) = HI.
By deducting the foresight rod reading from the instrument's height, the elevation is computed. The elevation reading of a site with unknown elevation is called a foresight.
An intermediate location between benchmarks known as a turning point (T.P.) offers a temporary point of known elevation for a level circuit between two benchmarks that are far apart.
To learn more about elevation using different level refer to :
https://brainly.com/question/13768617
#SPJ4
high traffic volume allows more vehicles on the expressway due to the design of a) speed limits b) medians c) exits d) multiple lane roads
Answer:
d) multiple lane roads
Explanation:
High traffic volume allows more vehicles on the expressway due to the design of multiple lane roads. The correct option is d.
What is an expressway?Expressways are split, high-speed thoroughfares for through traffic with partially or completely restricted access.
Roadways that connect significant cities, villages, and other locations are referred to as highways, and they often feature four lanes to accommodate high-speed traffic.
However, an expressway is a high-speed route with limited access that has a number of infrastructure such access ramps and lane separators.
The term "highway" derives from elevated Roman highways that featured a mound or hill in the middle created by earth thrown from side ditches.
Because multiple lane highways are designed for high traffic volumes, there can be more vehicles on the expressway.
Thus, the correct option is d.
For more details regarding expressway, visit:
https://brainly.com/question/4371083
#SPJ2
consider the loading shown. note: this is a multi-part question. once an answer is submitted, you will be unable to return to this part. identify the equation of the elastic curve for the cantilever beam ab.
I is the section's second moment of area or moment of inertia. The following techniques can be used to determine the equation for the elastic curve of a beam.
The first and second derivatives of the function that represents the curve in terms of the Cartesian coordinates x and y are dydx and d2ydx2, respectively. Assuming that the longitudinal stresses on the fibers are within the elastic limit, the elastic curve of a beam is the curve formed by the intersection of the neutral surface with the side of the beam. The Bending Moment Equation's double integral is taken in order to perform the fundamental calculation. There are formulas for both cantilever beams and beams that are simply supported.
Learn more about stresses here-
https://brainly.com/question/17252580
#SPJ4
Technician A says low fluid level in the master cylinder reservoir indicates a leak in the system.
Technician B says for both drum and disc brakes, the friction material rotates with the wheel.
Who is right?
Select the correct option and click NEXT
O A only
B only
Both A and B
Neither A nor B
Technician A says the low fluid level in the master cylinder reservoir indicates a leak in the system. Technician B says for both drum and disc brakes, the friction material rotates with the wheel. Both A and B are correct.
What is a technician?A technician is a person who knows the technicality of machines and other things, They can repair these things.
These rubber rings prevent hydraulic fluid from escaping and keep it free of moisture and impurities. They also cause the piston to return to its off position, allowing the brake pads to disengage correctly when the brake pedal is released.
Therefore, the correct option is c, Both A and B.
To learn more about technicians, refer to the link:
https://brainly.com/question/19796461
#SPJ1
(20%) machining appears to play an important role in the manufacturing of this phone housing, but machining is a relatively slow process. can you explain why machining was chosen instead of sheet-metal forming or casting alone? list the major considerations and compare among all these processes to justify your answer.
No raw material is wasted during the metal forming process, and the product has higher mechanical qualities and is produced more quickly.
By using a wedge-shaped tool, machining is the removal of material in the form of chips. Metal plates, tubes, or solid round bars make up the material that is machined. On the other hand, metal flat sheets make up the material that goes through the fabrication process. Metal is heated in a furnace until molten before being cast. The metal is poured into a die, or mold, while it is still liquid, giving the metal the shape of the component.
Learn more about mechanical here-
https://brainly.com/question/20434227
#SPJ4
what would be considered a higher-than-normal tempertaure for a discharge gas line on a reciprocating compressor
Any compressor's discharge temperature cannot exceed 225 degrees F. if the discharge temperature rises above 225 degrees.
What temperature should a reciprocating compressor's discharge gas line be at?However, many compressor packages will contain components that limit discharge temperature to no more than 148.9°C (300°F). In general, it is advised to never exceed operating discharge temperatures of 176.7°C (350°F).
What are the likely reasons why the compressor discharge has an excessively high discharge pressure?The primary cause of high condensing pressure is high discharge pressure. High condensing pressure can be caused by insufficient condenser heat dissipation, condenser fouling, insufficient cooling air or water volume, and high cooling water or air temperature.
To know more about compressor visit :-
https://brainly.com/question/26581412
#SPJ4
Cognitive computing, which is also called _____ computing, aims to mimic the functioning of the human brain through greater interconnectivity among memory, processors, and communications.
a. hybrid memory
b. core
c. neurosynaptic
d. quantum
Answer: c
Cognitive computing, which is also called neurosynaptic computing, aims to mimic the functioning of the human brain through greater interconnectivity among memory, processors, and communications.
A cognitive chip or neurosynaptic chip is a type of computer processor that works more like a biological brain than a normal CPU.
Neurosynaptic chips are designed to operate like human brains on the hardware level, in contrast to cognitive computing and neural networks, which use software to simulate human thought and learning. Even if a normal computer is effective at processing language, mathematics, and data analytics, it can be labor-intensive for it to carry out tasks that even rudimentary biological brains are proficient at. These processes, which include pattern recognition, sensory processing, and learning, are more effectively performed by a neurosynaptic device. The neurosynaptic chip has the potential to change capabilities, particularly in mobile technologies where computation and power are constrained.
Learn more about operate here-
https://brainly.com/question/27960749
#SPJ4
use the myhill-nerode theorem to prove that the languages in exercise 1.29 (a and c), page 88 and problem 1.46 (b and c) page 90, are not regular. Aa. A1 = {01" 2" | n >0} b. 12 = {www w€ {a,b}*} Ac. Az = {a?" | n >0} (Here, a?" means a means a string of 2" a's.)
A string, often known as a word, is a limited collection of an alphabet's symbols.
Instances of strings over the letters "a, b" include "b, a" and "aabab," whereas "0, 10" and "001" are examples of strings over the letters "0, 1." A language is a collection of words written in an alphabet. As a result, (b + ab)* can be used to represent a string before the aa. Therefore, if a language string contains aa, the regular expression (b + ab) applies. *aa(b + ba)* The requirement is that every string created by the regular expression must have at least two a's, but there is no restriction on the quantity or placement of b's and c's. Therefore, (a+b+c)*. (a+b+c)*.
Learn more about placement here-
https://brainly.com/question/29229544
#SPJ4