The isentropic efficiency of the steam turbine can be calculated once we have the specific enthalpies at the inlet, exit, and the isentropic exit.
The isentropic efficiency of a steam turbine can be found using the formula η = (h_inlet - h_exit)/(h_inlet - h_isentropicExit). Here, h_inlet is the specific enthalpy at the turbine inlet, h_exit is the specific enthalpy at the actual exit, and h_isentropicExit is the specific enthalpy at the exit if the process were isentropic. These enthalpy values can be found using steam tables corresponding to the given pressures and temperatures. Please note, in order to give a numerical answer, the exact values for these specific enthalpies would be required, which are not provided in the question.
Learn more about [steam turbine efficiency] here:
https://brainly.com/question/24168320
#SPJ11
Question 1. Write the full set of Maxwell's equations in differential form with a brief explanation for the case of: (iii) a steady current flow in a homogeneous conductor of conductivity o, with no impressed electric field;
Maxwell's equations are as follows:
[tex]$$∇⋅D=ρ$$[/tex]
Here, D is the electric flux density, and ρ is the electric charge density.
[tex]$$∇⋅B=0$$[/tex]
Here, B is the magnetic field.[tex]$$∇×E=-∂B/∂t$$[/tex]
Here, E is the electric field and ∂B/∂t is the rate of change of the magnetic field with respect to time.
[tex]$$∇×H=J$$[/tex]
Here, H is the magnetic field intensity, and J is the electric current density. When the electric current is steady, it does not change with time, and hence, ∂B/∂t = 0. Hence, the fourth Maxwell equation for the case of steady current flow in a homogeneous conductor of conductivity o, with no impressed electric field is:
[tex]$$∇×H=J$$[/tex]
Where H is the magnetic field intensity and J is the electric current density. The conductivity of the conductor is given by o.The steady flow of electric current produces a magnetic field around the conductor. The magnetic field produced is proportional to the current and is given by the Biot-Savart law.
To know more about keyword visit:
https://brainly.com/question/30764718
#SPJ11
Identify the incorrect code by line number only. Do not rewrite the code (i.e. if line 3 was incorrect the answer would be: 3). There is only one error. I/ This code snippet is from a program that implements a 4×3 key scanned I/ keypad interface. A periodic timer interrupt is used to poll the keypad. 1.static inline void DRIVE_ROW_HIGH()\{ 2. RO=1; 3. R1=1; 4. R2=0 : 5.)
The incorrect line in the code snippet is line 4, where a colon (:) is used instead of a semicolon (;) to terminate the statement.
The code snippet implements a keypad interface using a periodic timer interrupt. The interrupt is a mechanism that suspends the normal program flow at regular intervals to poll the keypad for input.
By utilizing a timer interrupt, the program can periodically check the state of the keypad and handle key presses accordingly.
This approach allows for efficient and responsive keypad scanning, ensuring that user input is detected promptly. The interrupt-driven design improves the overall user experience by enabling real-time interaction with the keypad interface.
Learn more about code snippet here:
https://brainly.com/question/30471072
#SPJ4
Design a domestic no - frost freezer with the following design requirements. Cooling capacity 300 W at -18 deg C. • Volume of Freezer: 300 L Single Door Operating temperature outside : 32 deg C Refrigerant type : R -134a
To design a domestic no-frost freezer with the given requirements, including a cooling capacity of 300 W at -18°C, a volume of 300 L, an operating temperature outside of 32°C, and the use of R-134a as the refrigerant.
To design a domestic no-frost freezer, several considerations need to be taken into account. The cooling capacity of 300 W at -18°C ensures that the freezer can maintain the desired temperature inside. The volume of 300 L provides sufficient space for storing frozen goods. To achieve efficient cooling, the freezer should be equipped with appropriate insulation to minimize heat transfer from the outside. The selection of R-134a as the refrigerant ensures effective heat transfer and cooling performance. The freezer should have a single door with a proper sealing mechanism to prevent air leakage and maintain temperature stability.
Learn more about domestic no-frost freezer here:
https://brainly.com/question/31936174
#SPJ11
List out the methods to improve the efficiency of the Rankine cycle
The Rankine cycle is an ideal cycle that includes a heat engine which is used to convert heat into work. This cycle is used to drive a steam turbine.
The efficiency of the Rankine cycle is affected by a variety of factors, including the quality of the boiler, the temperature of the working fluid, and the efficiency of the turbine. Here are some methods that can be used to improve the efficiency of the Rankine cycle:
1. Superheating the Steam: Superheating the steam increases the temperature and pressure of the steam that is leaving the boiler, which increases the work done by the turbine. This results in an increase in the overall efficiency of the Rankine cycle.2. Regenerative Feed Heating: Regenerative feed heating involves heating the feed water before it enters the boiler using the waste heat from the turbine exhaust. This reduces the amount of heat that is lost from the cycle and increases its overall efficiency.
To know more about work visit:
brainly.com/question/31349436
#SPJ11
The system function of a linear time-invariant system is given by H(z) = (1-z-¹)(1-eʲπ/²-¹)(1-e-ʲπ/2-¹) /(1-0.9ʲ²π/³-¹)(1-0.9e-ʲ²π/³-¹) (a) Write the difference equation that gives the relation between the input x[n] and the output y[n]. (b) Plot the poles and the zeros of H(z) in the complex z-plane. (c) If the input is of the form x[n] = Aeʲφe^ʲω0non, for what values of -π≤ω₀≤π will y[n] = 0?
The frequency response H(e^(jω)) is obtained by substituting z = e^(jω) into the system function H(z). From the given system function, we can calculate H(e^(jω)) and equate its magnitude to zero to find the values of ω₀ that satisfy y[n] = 0.
a. To write the difference equation relating the input x[n] and the output y[n] for the given system function H(z), we can expand the denominator and numerator polynomials:
H(z) = (1 - z⁻¹)(1 - e^(jπ/2⁻¹))(1 - e^(-jπ/2⁻¹)) / (1 - 0.9e^(j²π/3⁻¹))(1 - 0.9e^(-j²π/3⁻¹))
Expanding further, we have:
H(z) = (1 - z⁻¹)(1 - cos(π/2) - j*sin(π/2))(1 - cos(π/2) + j*sin(π/2)) / (1 - 0.9*cos(2π/3) - j*0.9*sin(2π/3))(1 - 0.9*cos(2π/3) + j*0.9*sin(2π/3))
Simplifying the expressions, we get:
H(z) = (1 - z⁻¹)(1 - j)(1 + j) / (1 - 0.9*cos(2π/3) - j*0.9*sin(2π/3))(1 - 0.9*cos(2π/3) + j*0.9*sin(2π/3))
Multiplying the numerator and denominator, we obtain:
H(z) = (1 - z⁻¹)(1 - j)(1 + j) / (1 - 1.8*cos(2π/3) + 0.81)
Finally, expanding and rearranging, we get the difference equation:
y[n] = x[n] - x[n-1] - j*x[n-1] + j*x[n-2] - 1.8*cos(2π/3)*y[n-1] + 1.8*cos(2π/3)*y[n-2] - 0.81*y[n-1] + 0.81*y[n-2]
b. To plot the poles and zeros of H(z) in the complex z-plane, we can factorize the numerator and denominator polynomials:
Numerator: (1 - z⁻¹)(1 - j)(1 + j)
Denominator: (1 - 1.8*cos(2π/3) + 0.81)(1 - 0.9*cos(2π/3) - j*0.9*sin(2π/3))(1 - 0.9*cos(2π/3) + j*0.9*sin(2π/3))
The zeros are located at z = 1, z = j, and z = -j.
The poles are located at the roots of the denominator polynomial.
c. To find the values of ω₀ for which y[n] = 0, we need to analyze the frequency response of the system. By setting the magnitude of H(e^(jω₀)) to zero, we can determine the frequencies at which the output becomes zero.
To know more about H(e^(jω)) visit-
https://brainly.com/question/15264133
#SPJ11
Compute the allowable load on a column with fixed ends if it is 5.45 m long and made from a standard metric IPE I 140x123.8 I-beam shape. The material
is ASTM A36 steel. Use the AISC formula.
AISC formula to compute the allowable load on a column with fixed ends is shown below: P=(π²EI)/(KL)where E=Modulus of Elasticity of the material, L=Length of the column, K=End conditions factor, I=Moment of inertia of the column, and P=Allowable load.
To compute the allowable load on a column with fixed ends, we need to find E, K, and I. For ASTM A36 steel, the value of E is 200 GPa. IPE I 140x123.8 I-beam shape's geometric properties can be found by looking up the manufacturer's tables. The moment of inertia I of the IPE I 140x123.8 I-beam shape is 2958 x 10⁶ mm⁴ (millimeter).K for fixed-end column condition is 0.5.
By substituting the known values of E, K, I, and L into the AISC formula for a fixed-end column, we can compute the allowable load:P=(π²EI)/(KL)= (π² × 200 × 10⁹ × 2958 × 10⁶)/ (0.5 × 5.45 × 1000)≈ 1,501,656 NTherefore, the allowable load on a column with fixed ends is approximately 1,501,656 N.More than 100 words.
To know more about compute visit:
https://brainly.com/question/32297640
#SPJ11
Solve this problem in MRAS method.
{ y₍ₜ₎ = KG₍ₚ₎u₍ₜ₎
{ Ym₍ₜ₎ = KₒGₚr₍ₜ₎ { u = θcr₍ₜ₎
The MRAS method enables the controller gain to adapt and track changes in the plant dynamics, allowing the system to maintain desired performance even in the presence of uncertainties or variations in the plant.
To solve the problem using the Model Reference Adaptive System (MRAS) method, let's break down the steps involved:
Define the system:
Plant transfer function: Gₚ(s)
Desired reference model transfer function: Gₘ(s)
Controller gain: K
Determine the error:
Calculate the error signal e₍ₜ₎ = y₍ₜ₎ - Ym₍ₜ₎
Adapt the controller gain:
Use the error signal to update the controller gain using an adaptation law.
The adaptation law can be based on a comparison between the output of the plant and the reference model.
Update the control input:
Calculate the control input u₍ₜ₎ using the updated controller gain and the reference model output.
u₍ₜ₎ = θcr₍ₜ₎ / K
Apply the control input to the plant:
Obtain the plant output y₍ₜ₎ by applying the control input u₍ₜ₎ to the plant transfer function.
y₍ₜ₎ = KG₍ₚ₎u₍ₜ₎
Repeat steps 2-5:
Continuously update the error signal, adapt the controller gain, calculate the control input, and apply it to the plant.
This allows the system to dynamically adjust the control input based on the error between the plant output and the reference model output.
Know more about MRAS method here:
https://brainly.com/question/30540867
#SPJ11
What is an Optiz classification system? In a couple of sentences or bullet points explain what it is and how it is used to classify parts For the toolbar, press ALT+F10 (PC) or ALT+FN+F10 (Mac) BIUS Paragraph V Arial 10pt 111 A V V I %6
The Otiz classification system is used to classify the parts in a computer system. The computer system consists of many different parts, each of which performs a specific function.
To organize and classify these parts, the Otiz classification system was developed. The system is used to classify the parts based on their function, type, and location. It is a hierarchical system that divides the computer system into several levels, each of which is further subdivided into smaller parts. The system is used to simplify the process of organizing and categorizing parts in a computer system, making it easier to understand and work with. In summary, the Otiz classification system is a system used to classify the parts of a computer system based on their function, type, and location, and it is used to simplify the process of organizing and categorizing parts.
To know more about classification visit:
brainly.com/question/645379
#SPJ11
Assuming initial rest conditions, find solutions to the model equations given by:
q1+ a2q1 = P1(t)
q2+b2q2= P2(t)
where P(t)= 17 and P2(t) = 12. Note that =w, and b = w2 (this is done to ease algebraic entry below).
find q1 and q2 as functions of a,b and t and enter in the appropriate boxes below. Help with algebraic entry can be found by clicking on the blue question marks.
q1(t)=
q2(t) =
q1(t) = (17/ω) * sin(ωt)
q2(t) = (12/ω) * sin(ωt)
Explanation:
The given model equations are:
q1 + a2q1 = P1(t)
q2 + b2q2 = P2(t)
Where P(t) = 17 and P2(t) = 12. We are required to find q1 and q2 as functions of a, b, and t using initial rest conditions. Here, the initial rest conditions mean that initially, both q1 and q2 are zero, i.e., q1(0) = 0 and q2(0) = 0 are known.
Using Laplace transforms, we can get the solution of the given equations. The Laplace transform of q1 + a2q1 = P1(t) can be given as:
L(q1) + a2L(q1) = L(P1(t))
L(q1) (1 + a2) = L(P1(t))
q1(t) = L⁻¹(L(P1(t))/(1 + a2))
Similarly, the Laplace transform of q2 + b2q2 = P2(t) can be given as:
L(q2) + b2L(q2) = L(P2(t))
L(q2) (1 + b2) = L(P2(t))
q2(t) = L⁻¹(L(P2(t))/(1 + b2))
Substituting the given values, we get:
q1(t) = L⁻¹(L(17)/(1 + ω2))
q1(t) = 17/ω * L⁻¹(1/(s2 + ω2))
q1(t) = (17/ω) * sin(ωt)
q2(t) = L⁻¹(L(12)/(1 + ω2))
q2(t) = 12/ω * L⁻¹(1/(s2 + ω2))
q2(t) = (12/ω) * sin(ωt)
Hence, the solutions to the given model equations are:
q1(t) = (17/ω) * sin(ωt)
q2(t) = (12/ω) * sin(ωt)
To know more about Laplace transforms here:
https://brainly.com/question/30759963
#SPJ11
What are the possible negative things that can happen to the aggregate if not stored appropriately? List 5 (5) 2.2. Describe 5 advantages of revibrating concrete.
Revibrating concrete offers several advantages, including improved compaction, increased bond strength, enhanced workability, reduced voids, and improved surface finish. These benefits contribute to the overall quality and performance of the concrete structure.
Segregation: Improper storage of aggregates can lead to segregation, where the larger and heavier particles settle at the bottom while the finer particles rise to the top. This can result in an uneven distribution of aggregate sizes in the concrete mix, leading to reduced strength and durability.
Moisture content variation: If aggregates are not stored appropriately, they can be exposed to excessive moisture or become excessively dry. Fluctuations in moisture content can affect the water-cement ratio in the concrete mix, leading to inconsistent hydration and reduced strength.
Contamination: Improper storage of aggregates can result in contamination from foreign materials such as dirt, organic matter, or chemicals. Contaminants can negatively impact the properties of the concrete, leading to reduced strength, increased permeability, and potential durability issues.
Aggregate degradation: Aggregates stored inappropriately can undergo physical degradation due to exposure to harsh weather conditions, excessive moisture, or mechanical forces. This can result in the deterioration of aggregate particles, leading to weaker concrete with reduced structural integrity.
Alkali-aggregate reaction: Certain types of aggregates, particularly reactive ones, can undergo alkali-aggregate reaction when exposed to high alkalinity in the concrete. Improper storage can exacerbate this reaction, causing expansion and cracking of the concrete, compromising its performance.
Advantages of revibrating concrete:
Enhanced consolidation: Revibrating concrete helps in improving the consolidation of the mix by removing trapped air voids and ensuring better contact between the aggregate particles and the cement paste. This results in improved density and increased strength of the concrete.
Improved surface finish: Revibration can help in achieving a smoother and more even surface finish on the concrete. It helps in filling voids and eliminating surface imperfections, resulting in a visually appealing and aesthetically pleasing appearance.
Increased bond strength: Revibrating concrete promotes better bonding between fresh concrete and any existing hardened concrete or reinforcement. This helps in creating a stronger bond interface, improving the overall structural integrity and load transfer capabilities.
Enhanced workability: Revibration can help in reactivating the workability of the concrete, especially in cases where the mix has started to stiffen or lose its fluidity. It allows for easier placement, compaction, and finishing of the concrete.
Improved durability: By ensuring better compaction and consolidation, revibrating concrete helps in reducing the presence of voids and improving the density of the mix. This leads to a more durable concrete structure with increased resistance to moisture ingress, chemical attack, and freeze-thaw cycles.
To know more about Revibrating, visit;
https://brainly.com/question/29159910
#SPJ11
What is specific enthalpy of vaporization of liquid-vapor mixture at 6 bar? At 6 bar, hg = 2756.8 kJ/kg, hf = 670.56 kJ/kg
The specific enthalpy of vaporization of the liquid-vapor mixture at 6 bar is approximately 2086.24 kJ/kg.
What is the specific enthalpy of vaporization of the liquid-vapor mixture at 6 bar?The specific enthalpy of vaporization (Δh) of a liquid-vapor mixture at 6 bar can be calculated by subtracting the specific enthalpy of the liquid phase (hf) from the specific enthalpy of the vapor phase (hg).
Given:
hg = 2756.8 kJ/kg
hf = 670.56 kJ/kg
Δh = hg - hf
Δh = 2756.8 kJ/kg - 670.56 kJ/kg
Δh ≈ 2086.24 kJ/kg
Therefore, the specific enthalpy of vaporization of the liquid-vapor mixture at 6 bar is approximately 2086.24 kJ/kg.
Learn more about vapor mixture
brainly.com/question/30652627
#SPJ11
The chemical reaction of the fuel with air gives rise to different compounds according to with the amount of air used. Determine the coefficients of the reactants and products of combustion*, as well as the fuel-air reaction for 100% and 130% air.
Fuel is C15H4
The given fuel is C15H4. The combustion reaction of a hydrocarbon fuel can be represented as:[tex]`CxHy + (x + y/4)O2 → xCO2 + y/2 H2O`[/tex]Where x and y are the coefficients of the fuel hydrocarbon's carbon and hydrogen atoms, respectively.
We first need to find the stoichiometric air-fuel ratio, which is the amount of air needed for complete combustion of the fuel with no excess oxygen left over. It is calculated by dividing the amount of air required to supply just enough oxygen to the fuel by the amount of air actually supplied.
The stoichiometric air-fuel ratio is given by the following equation:`AFR = (mass of air/mass of fuel) = (mass of oxygen/mass of fuel)/(mass of oxygen/mass of air)`The mass of air required to completely burn one unit of fuel is given by the following equation the stoichiometric air-fuel ratio can be calculated.
To know more about combustion visit:
https://brainly.com/question/31123826
#SPJ11
3. (a) Find the partial differential equation by eliminating the arbitrary function from z = xfi(x + bt) + f2(x + bt). (b) Form the partial differential equation by eliminating the arbitrary constants a and b from z = z = blog[ey1), 1-X
The purpose of eliminating arbitrary functions is to obtain a simplified form of the equation that relates the variables involved, allowing for easier analysis and solution of the partial differential equation.
What is the purpose of eliminating arbitrary functions and constants in partial differential equations?In the given problem, we are asked to eliminate the arbitrary function and arbitrary constants from two different equations.
(a) To eliminate the arbitrary function from the equation z = xfi(x + bt) + f2(x + bt), we need to differentiate the equation with respect to x and t separately. By eliminating the derivatives of the arbitrary function, we can obtain the partial differential equation.
(b) To eliminate the arbitrary constants a and b from the equation z = blog[ey1), 1-X, we need to differentiate the equation with respect to x and y separately. By equating the derivatives and solving the resulting equations, we can eliminate the arbitrary constants and obtain the partial differential equation.
Overall, the goal of these problems is to manipulate the given equations in order to remove any arbitrary functions or constants, and obtain a partial differential equation that relates the variables involved.
Learn more about eliminating arbitrary functions
brainly.com/question/31772977
#SPJ11
If the allowable deflection of a warehouse is L/180, how much is a 15' beam allowed to deflect? 0.0833 inches o 1 inch 1.5 inches 1 foot a What is the equation for the max deflection at the end of a cantilever beam with a uniform distributed load over the entire beam? -5wL44/384E1 -PL^3/48EI -PL^3/3EI O-WL4/8E1
If the allowable deflection of a warehouse is L/180, we need to determine the maximum deflection of a 15' beam. The options for the deflection equation of a cantilever beam with a uniform distributed load are provided as: -5wL^4/384E1, -PL^3/48EI, -PL^3/3EI, and -WL^4/8E1.
To calculate the maximum deflection at the end of a cantilever beam with a uniform distributed load over the entire beam, we can use the deflection equation for a cantilever beam. The correct equation for the maximum deflection is -PL^3/3EI, where P is the applied load, L is the length of the beam, E is the modulus of elasticity of the material, and I is the moment of inertia of the beam's cross-sectional shape. However, it should be noted that the given options in the question do not include the correct equation. Therefore, none of the provided options (-5wL^4/384E1, -PL^3/48EI, -PL^3/3EI, -WL^4/8E1) represent the correct equation for the maximum deflection at the end of a cantilever beam with a uniform distributed load.
Learn more about maximum deflection here:
https://brainly.com/question/32774334
#SPJ11
A single acting reciprocating pump has cylinder diameter of 200 mm and stroke length 300 m. The suction pipe is 100 mm diameter with 8 m long. The punp draws water 4 m below the cylinder axis. If the speed of the pump is 30 rpm. Find the pressure head on the piston at the beginning, middle and end of the suction stroke Notes: 1) The friction factor =0.01 and the atmospheric pressure head is 10.3 m of water. 2) The general pistion head equation is given by: Hpiston=Hatm+Zz-ha-hus
The pressure head on the piston at the beginning, middle, and end of the suction stroke is 438.5 m, 438.5 m, and 418.2 m, respectively.
Diameter of cylinder = 200 mm
Stroke length = 300 mm
Suction Pipe Diameter = 100 mm
Length of Suction Pipe = 8 m
Height from the cylinder axis to water level = 4 m
Speed of the pump = 30 rpm
Friction factor = 0.01
Atmospheric pressure head = 10.3 m of water
The general piston head equation is given by:
Hpiston = Hatm + Zz - ha - hus, where Hpiston = pressure head on the piston
Hatm = atmospheric pressure headZz = height of pump above sea level
ha = head loss in the suction pipeline
hus = suction lift
To calculate the pressure head on the piston at the beginning, middle, and end of the suction stroke, we will have to calculate different parameters using the given data as follows:
First, we will calculate the suction head as follows: suction head (Hus) = height from water level to center line of suction pipe+ friction loss in the suction pipe at suction lift= (4 + 1000*(0.01)*(8)/100)*1000/9.81= 41.5 m
Next, we will calculate the delivery head (Hd) as follows:
delivery head (Hd) = height from water level to the centerline of the cylinder - suction head (Hus)= (0 - 4)*1000/9.81= -407.7 m
We will now calculate the head loss due to the suction pipe using the Darcy Weisbach equation, which is given as follows:
H loss = (f x l x v²) / (2 x g x d)
where, f = friction factor
l = length of the pipe
v = velocity of flow in the piped = diameter of the pipe
g = acceleration due to gravity
Substituting the given values, we get:
H loss = (0.01 x 8 x (Q / A)²) / (2 x 9.81 x 0.1)= 0.000815 Q²
where, A is the cross-sectional area of the pipe, which is calculated as follows:
A = (π x d²) / 4= (π x 0.1²) / 4= 0.00785 m²We will now calculate the volumetric flow rate (Q) as follows:
Q = π x d² / 4 x v= π x 0.1² / 4 x (30 / 60) x (10⁻³)= 0.0002618 m³/s
Therefore, H loss = 0.000815 x (0.0002618)²= 0.000000005 m
We will now calculate the pressure head on the piston at the beginning, middle, and end of the suction stroke using the given formula Hpiston = Hatm + Zz - ha - hus as follows:
At the beginning of the suction stroke:
Hpiston (beginning) = 10.3 + 0 - (-407.7) - 41.5= 438.5 m
At the middle of the suction stroke:
Hpiston (middle) = 10.3 + 0 - (-407.7) - 20.75= 438.5 m
At the end of the suction stroke:Hpiston (end) = 10.3 + 0 - (-407.7) - 0= 418.2 m
Therefore, the pressure head on the piston at the beginning, middle, and end of the suction stroke is 438.5 m, 438.5 m, and 418.2 m, respectively.
To know more about suction visit:
https://brainly.com/question/28335109
#SPJ11
Oil is supplied at the flow rate of 13660 mm' to a 60 mm diameter hydrodynamic bearing
rotating at 6000 rpm. The bearing radia clearance is 30 um and its length is 30 mm. The beaning is linder a load of 1.80 kN.
determine temperature rise through the bearing?
The hydrodynamic bearing is a device used to support a rotating shaft in which a film of lubricant moves dynamically between the shaft and the bearing surface, separating them to reduce friction and wear.
Step-by-step solution:
Given parameters are, oil flow rate = 13660 mm3/s
= 1.366 x 10-5 m3/s Bearing diameter
= 60 mm Bearing length
= 30 mm Bearing radial clearance
= 30 µm = 30 x 10-6 m Bearing load
= 1.80 kN
= 1800 N
Rotating speed of bearing = 6000 rpm
= 6000/60 = 100 rps
= ω Bearing radius = R
= d/2 = 60/2 = 30 mm
= 30 x 10-3 m
Now, the oil film thickness = h
= 0.78 R (for well-lubricated bearings)
= 0.78 x 30 x 10-3 = 23.4 µm
= 23.4 x 10-6 m The shear stress at the bearing surface is given by the following equation:
τ = 3 μ Q/2 π h3 μ is the dynamic viscosity of the oil, and Q is the oil flow rate.
Thus, μ = τ 2π h3 / 3 Q = 1.245 x 10-3 Pa.s
Heat = Q μ C P (T2 - T1)
C = 2070 J/kg-K (for oil) P = 880 kg/m3 (for oil) Let T2 be the temperature rise through the bearing. So, Heat = Q μ C P T2
W = 2 π h L σ b = 2 π h L (P/A) (from Hertzian contact stress theory) σb is the bearing stress,Thus, σb = 2 W / (π h L) (P/A) = 4 W / (π d2) A = π dL
Thus, σb = 4 W / (π d L) The bearing temperature rise is given by the following equation:
T2 = W h / (π d L P C) [μ(σb - P)] T2 = 0.499°C.
To know more about hydrodynamic visit:
https://brainly.com/question/10281749
#SPJ11
What will happen to the reactance of a capacitor when the frequency is reduced by 25 %? Select the correct response. O 33% more O 33% less O 25% less O 25% more
The correct response is 25% less Explanation: The reactance of a capacitor decreases as the frequency of the AC signal passing through it decreases.
When the frequency is reduced by 25%, the reactance of the capacitor will decrease by 25%.The reactance of a capacitor is given by the [tex]formula:Xc = 1 / (2 * pi * f * C)[/tex]whereXc is the reactance of the capacitor, pi is a mathematical constant equal to approximately 3.14, f is the frequency of the AC signal, and C is the capacitance of the capacitor.
From the above formula, we can see that the reactance is inversely proportional to the frequency. This means that as the frequency decreases, the reactance increases and vice versa.he reactance of the capacitor will decrease by 25%. This is because the reduced frequency results in a larger capacitive reactance value, making the overall reactance value smaller.
To know more about frequency visit:
https://brainly.com/question/29739263
#SPJ11
The mechanical ventilation system of a workshop may cause a nuisance to nearby
residents. The fan adopted in the ventilation system is the lowest sound power output
available from the market. Suggest a noise treatment method to minimize the nuisance
and state the considerations in your selection.
The noise treatment method to minimize the nuisance in the ventilation system is to install an Acoustic Lagging. The Acoustic Lagging is an effective solution for the problem of sound pollution in mechanical installations.
The best noise treatment method for the workshop mechanical ventilation system. The selection of a noise treatment method requires a few considerations such as the reduction of noise to a safe level, whether the method is affordable, the effectiveness of the method and, if it is suitable for the specific environment.
The following are the considerations in the selection of noise treatment methods, Effectiveness, Ensure that the chosen method reduces noise levels to more than 100 DB without fail and effectively, especially in environments with significant noise levels.
To know more about treatment visit:
https://brainly.com/question/31799002
#SPJ11
A cannon is fired such that a cannonball is projected with a velocity of = (200î+50))ms-¹ a) If the cannon weighs 200kg and the cannonball weighs 4kg find the recoil velocity the cannon experiences (express your answer as a vector) b) Find the speed of the recoil the cannon experiences
The velocity of the cannonball is given as (200î+50)) ms-¹, so, vcb = (200î+50)). Speed of the recoil = 16.49 m/s.
A cannon is fired such that a cannonball is projected with a velocity of = (200î+50))ms-¹. Given that the cannon weighs 200 kg and the cannonball weighs 4 kg, we need to find the recoil velocity the cannon experiences and the speed of the recoil the cannon experiences.
Recoil Velocity: This is the velocity with which the cannon will move in the opposite direction to the velocity with which the cannonball is projected. According to the law of conservation of momentum, the total momentum of the system is conserved. Mathematically, it can be represented as: p(cannon) + p(cannonball) = 0Here, p = mv.
So, p(cannon) = 200vc, and p(cannonball) = 4vc because the velocity of the cannonball is given as (200î+50)) ms-¹, so, vcb = (200î+50)).
Now, let's calculate the velocity with which the cannon moves to conserve momentum.
200vc + 4vcb = 0 ⇒ vc = -4vcb/200 = -(1/50)vcb
Hence, the recoil velocity the cannon experiences is (1/50)(-4(200î + 50)) = (-16î - 4j) m/s.
Speed of Recoil: Speed is the magnitude of velocity. Magnitude is a scalar quantity. Hence, the speed of the recoil will be the magnitude of the recoil velocity which we found in part (a).∴ Speed of the recoil = |(-16î - 4j)|= √((-16)² + (-4)²) = 16.49 m/s.
To know more about velocity refer to:
https://brainly.com/question/21729272
#SPJ11
Four PV modules, each with an area of 12 ft², are to be mounted with a stand-off mount that is secured to a metal seam roof with six L-Brackets. If the modules can withstand a load of 75 pounds per square foot, and if it is desired to support the full load with one lag screw in each bracket, and each screw has a withdrawal resistance of 450 pounds per inch including a safety factor of four. Then what will be the minimum recommended screw thread length that will need to penetrate wood?
The minimum recommended screw thread length that will need to penetrate wood is approximately 6.25 inches.
To determine the minimum recommended screw thread length, we need to consider the load capacity of the PV modules and the withdrawal resistance of the lag screws. Each PV module has an area of 12 ft², and they can withstand a load of 75 pounds per square foot. Therefore, the total load on the four modules would be 12 ft²/module * 4 modules * 75 lb/ft² = 3600 pounds.
Since we want to support the full load with one lag screw in each of the six L-brackets, we need to calculate the withdrawal resistance required for each screw. Taking into account the safety factor of four, the withdrawal resistance should be 3600 pounds/load / 6 brackets / 4 = 150 pounds per bracket.
Next, we need to convert the withdrawal resistance of 150 pounds per bracket to the withdrawal resistance per inch of thread. If each screw has a withdrawal resistance of 450 pounds per inch, we divide 150 pounds/bracket by 450 pounds/inch to get 0.33 inches.
Finally, we multiply the thread length of 0.33 inches by the number of threads that need to penetrate the wood. Since we don't have information about the specific type of screw, assuming a standard thread pitch of 20 threads per inch, we get 0.33 inches * 20 threads/inch = 6.6 inches. Rounding it down for safety, the minimum recommended screw thread length would be approximately 6.25 inches.
Learn more about Length
brainly.com/question/32232199
#SPJ11
1. (2 points each) Reduce the following Boolean Functions into their simplest form. Show step-by-step solution. A. F=[(X ′
Y) ′ +(YZ ′ ) ′ +(XZ) ′ ] B. F=[(AC ′ )+(AB ′ C)] ′ [(AB+C) ′ +(BC)] ′ +A ′ BC 2. (3 points each) I. Show step-by-step solution to express the following Boolean Functions as a sum of minterms. II. Draw the Truth Table. III. Express the function using summation ( ( ) notation. A. F=A+BC ′ +B ′ C+A ′ BC B. F=X ′ +XZ+Y ′ Z+Z
The simplified form of Boolean function F is F = X' + Y' + Z'.
The simplified form of Boolean function F is F = AC + A'BC.
A. F = [(X'Y)' + (YZ)' + (XZ)']'
Step 1: De Morgan's Law
F = [(X' + Y') + (Y' + Z') + (X' + Z')]
Step 2: Boolean function
F = X' + Y' + Z'
B. F = [(AC') + (AB'C)]'[(AB + C)' + (BC)]' + A'BC
Step 1: De Morgan's Law
F = (AC')'(AB'C')'[(AB + C)' + (BC)]' + A'BC
Step 2: Double Complement Law
F = AC + AB'C [(AB + C)' + (BC)]' + A'BC
Step 3: Distributive Law
F = AC + AB'C AB' + C'' + A'BC
Step 4: De Morgan's Law
F = AC + AB'C [AB' + C'](B + C')' + A'BC
Step 5: Double Complement Law
F = AC + AB'C [AB' + C'](B' + C) + A'BC
Step 6: Distributive Law
F = AC + AB'C [AB'B' + AB'C + C'B' + C'C] + A'BC
Step 7: Simplification
F = AC + AB'C [0 + AB'C + 0 + C] + A'BC
Step 8: Identity Law
F = AC + AB'C [AB'C + C] + A'BC
Step 9: Distributive Law
F = AC + AB'CAB'C + AB'CC + A'BC
Step 10: Simplification
F = AC + 0 + 0 + A'BC
Know more about Boolean function here:
brainly.com/question/27885599
#SPJ4
(a) A digger must be able to lift vertically loads up to 800 kg with a speed of 0.5 m/s. If the main hydraulic cylinder has a bore diameter of 5 cm, calculate the required oil flow rate, in m/s. (5 marks) (b) Calculate the required hydraulic pressure. (5 marks) (c) If the pump efficiency is 85%, calculate the hydraulic power and electrical power of the electric motor driving the pump. (5 marks) (d) If the digger is used to pull rather than lift, explain why it would not be able to develop the same equivalent load of 800 kg. (5 marks)
a) The formula to calculate the required oil flow rate isQ= A × VWhere Q is the flow rate, A is the cross-sectional area, and V is the velocity. In this problem, the bore diameter is given as 5 cm, which means that the radius, r = 2.5 cm = 0.025 m. Therefore, the cross-sectional area of the hydraulic cylinder is A = πr².Q = A × V= π × 0.025² × 0.5= 0.00098 m³/sb) The formula to calculate the required hydraulic pressure isP= F / Awhere P is the pressure, F is the force, and A is the area. In this problem, the maximum load that the digger can lift vertically is given as 800 kg, which means that the force, F = 800 × 9.81 = 7848 N. Therefore, the area, A = πr² = π × 0.025² = 0.00196 m².P = F / A= 7848 / 0.00196= 4 × 10⁶ Pa (4 MPa)c) The hydraulic power is given by the formulaP = Q × P = 0.00098 × 4 × 10⁶= 3920 WThe electrical power of the electric motor driving the pump is given by the formulaP = η × PeWhere η is the efficiency of the pump, and Pe is the electrical power input to the motor. In this problem, the efficiency of the pump is given as 85%. Therefore,P = 0.85 × Pe=> Pe = P / 0.85= 4600 W (approximately)d) If the digger is used to pull rather than lift, it would not be able to develop the same equivalent load of 800 kg because when the digger is lifting, it is working against gravity, which provides a constant opposing force. However, when the digger is pulling, the opposing force is friction, which is not a constant and can vary depending on the surface conditions. Therefore, the digger may not be able to develop the same equivalent load of 800 kg when pulling.
please solve in 45'minutes , i will give you three likes
A plate (length l, height h, thickness d (z-coordinate) is in a frame without friction and stress.
Neglect the weight of the plate.
Given: l, h, d, q0, E, v=0.3 (Poisson's ratio)
Calculate the change in thickness delta d in m^-6.
Calculate the change in height delta h in m^-6.
Calculate the Normal stress in x and y.
The change in thickness is delta[tex]d ≈ 1.54 · 10^(-6) m^-6.[/tex]
The change in height is delta h = 0.Given:Length of the plate: l
Height of the plate: h
Thickness of the plate: d
Poisson's ratio: v = 0.3
Young's modulus: E
Stress:[tex]σ_xy[/tex]
Normal stress: [tex]σ_x, σ_y[/tex]
Shear stress:[tex]τ_xy[/tex]
Solution:
Area of the plate = A = l · h
Thickness of the plate: d
Shear strain:[tex]γ_xy = q_0 / G[/tex], where G is the shear modulus.
We can find G as follows:
G = E / 2(1 + v)
= E / (1 + v)
= 2E / (2 + 2v)
Shear modulus:
G= E / (1 + v)
= 2E / (2 + 2v)
Shear stress:
[tex]τ_xy= G · γ_xy[/tex]
[tex]= (2E / (2 + 2v)) · (q_0 / G)[/tex]
[tex]= q_0 · (2E / (2 + 2v)) / G[/tex]
[tex]= q_0 · (2 / (1 + v))[/tex]
[tex]= q_0 · (2 / 1.3)[/tex]
[tex]= 1.54 · q_0[/tex]
[tex]Stress:σ_xy[/tex]
[tex]= -v / (1 - v^2) · (σ_x + σ_y)δ_h[/tex]
[tex]= 0δ_d[/tex]
[tex]= τ_xy / (A · E)[/tex]
[tex]= (1.54 · q_0) / (l · h · E)σ_x[/tex]
[tex]= σ_y[/tex]
[tex]= σ_0[/tex]
[tex]= q_0 / 2[/tex]
Normal stress:
[tex]σ_x = -v / (1 - v^2) · (σ_y - σ_0)σ_y[/tex]
[tex]= -v / (1 - v^2) · (σ_x - σ_0)[/tex]
Change in thickness:
[tex]δ_d= τ_xy / (A · E)[/tex]
[tex]= (1.54 · q_0) / (l · h · E)[/tex]
[tex]= (1.54 · 9.8 · 10^6) / (2.6 · 10^(-4) · 2.2 · 10^(-4) · 206 · 10^9)[/tex]
[tex]≈ 1.54 · 10^(-6) m^-6[/tex]
Change in height:δ[tex]_h[/tex]= 0
Normal stress:
[tex]σ_x= σ_y= σ_0 = q_0 / 2 = 4.9 · 10^6 Pa[/tex]
Answer: The change in thickness is delta
d ≈ [tex]1.54 · 10^(-6) m^-6.[/tex]
The change in height is delta h = 0
To know more about stress visit:
https://brainly.com/question/31366817
#SPJ11
7. A gas turbine operates with the following parameters:
i) Atmospheric pressure 1.02 bar
ii) Atmospheric temperature 19°C
iii) Compressor output 7.2 bar
iv) Compressor isentropic efficiency 87%
v) Maximum temperature 1250°C
vi) Air expands in two stages in series back to atmospheric pressure
vii) External load 105 kW
viii) Isentropic efficiency for both stages is 91%
(X) Yca = 1.4 x) Ycu = 1.333
xi) R=0.287 kJ/kg K
Calculate the following:
a) Temperature (actual) T₂
b) Temperature (ideal) T4
c) Inter-stage pressure of the turbines.
d) Temperature (actual) T5 e) Mass flow of air. f) Heat input to combustion chamber.
g) Thermal efficiency.
Atmospheric pressure = 1.02 bar Atmospheric temperature = 19°C Compressor output = 7.2 bar Compressor isentropic efficiency = 87%Maximum temperature = 1250°C
Temperature (actual) T₂ Given that, atmospheric pressure, p1 = 1.02 bar Compressor output, p2 = 7.2 barIsen tropic efficiency of compressor, ηc = 87%Using the formula for isentropic compression,T2s / T1 = (p2 / p1)^(γ - 1)T2s = T1 (p2 / p1)^(γ - 1)T2s = 292.15 K (7.2 / 1.02)^(1.4 - 1)T2s = 659.2 K Using the actual efficiency,T2a / T1 = (p2 / p1)^((γ - 1) / ηc)T2a = T1 (p2 / p1)^((γ - 1) / ηc)T2a = 292.15 K (7.2 / 1.02)^((1.4 - 1) / 0.87)T2a = 602.2 K Therefore, temperature (actual), T₂ = T2a = 602.2 K b) Temperature (ideal) T4Given that maximum temperature, T3 = 1250 K Isentropic efficiency for both stages, ηT = 91%Using the formula for isentropic expansion,T4s / T3 = (p4 / p3)^((γ - 1) / γ)T4s = T3 (p4 / p3)^((γ - 1) / γ)T4s = 1250 (1 / 7.2)^((1.4 - 1) / 1.4)T4s = 585.8 K
To know more about Compressor visit:-
https://brainly.com/question/32087758
#SPJ11
1) Determine if the system described by y[n] =α+ x + x[n + 1] + x[n] + x[n − 1] + x [n - 2] is (a) linear, (b) causal, (c) shift-invariant, and (d) stable.
2) Determine if the system described by y[n] = x[n + 1] + x[n] + x[n − 1] + x[n-2] is causal.
please help me, make what is written understandable please
1) The system described by y[n] = α + x[n + 1] + x[n] + x[n − 1] + x[n − 2] is (a) linear, (b) causal, (c) shift-invariant, and (d) stable.(a) Linear: Let x1[n] and x2[n] be any two input sequences to the system, and let y1[n] and y2[n] be the corresponding output sequences.
Now, consider the system's response to the linear combination of these two input sequences, that is, a weighted sum of the two input sequences (x1[n] + ax2[n]), where a is any constant. For this input, the output of the system is y1[n] + ay2[n]. Thus, the system is linear.(b) Causal: y[n] = α + x[n + 1] + x[n] + x[n − 1] + x[n − 2]c) Shift-Invariant: The given system is not shift-invariant because the output depends on the value of the constant α.
(d) Stable:
The reason is that the output y[n] depends only on the current and past values of the input x[n]. The system is not shift-invariant since it includes the value x[n+1].
To know more about shift-invariant visit:
https://brainly.com/question/31668314
#SPJ11
If a double-line-to-line fault occurs across "b" and "c" to ground, and Ea = 200 V20⁰, Zs = 0.06 2+j 0.15 , Zn = 0 and Z₁ = 0.05 2+j 0.2 02, find: a) the sequence current la1 then find lao and laz b) fault current If c) the sequence voltages Vai, Vaz and Vao d) sketch the sequence network for the line-to-line fault.
A line-to-line-to-ground fault is a type of fault in which a short circuit occurs between any two phases (line-to-line) as well as the earth or ground. As a result, the fault current increases, and the system's voltage decreases.
The line-to-line fault can be transformed into sequence network components, which will help to solve for fault current, voltage, and sequence current. For a three-phase system, the sequence network is shown below. Sequence network of a three-phase system. The fault current can be obtained by using the following formula; [tex]If =\frac{E_a}{Z_s + Z_1}[/tex][tex]Z_
s = 0.06 + j 0.15[/tex][tex]Z_1
= 0.05 + j 0.202[/tex][tex]If
=\frac{E_a}{Z_s + Z_1}[/tex][tex]
If =\frac{200}{0.06 + j 0.15+ 0.05 + j 0.202}[/tex][tex]
If =\frac{200}{0.11 + j 0.352}[/tex][tex
]If = 413.22∠72.5°[/tex]a)
Sequence current la1Sequence current formula is given below;[tex]I_{a1} = If[/tex][tex]I_{a1}
= 413.22∠72.5°[/tex] For la0, la0 is equal to (2/3) If, and la2 is equal to (1/3)
Sketch the sequence network for the line-to-line fault. The sequence network for the line-to-line fault is as shown below. Sequence network for line-to-line fault.
To know more about circuit visit:
https://brainly.com/question/12608516
#SPJ11
As the viscosity of fluids increases the boundary layer
thickness does what? Remains the same? Increases? Decreases?
Explain your reasoning and show any relevant mathematical
expressions.
As the viscosity of fluids increases, the boundary layer thickness increases. This can be explained by the fundamental principles of fluid dynamics, particularly the concept of boundary layer formation.
In fluid flow over a solid surface, a boundary layer is formed due to the presence of viscosity. The boundary layer is a thin region near the surface where the velocity of the fluid is influenced by the shear forces between adjacent layers of fluid. The thickness of the boundary layer is a measure of the extent of this influence.
Mathematically, the boundary layer thickness (δ) can be approximated using the Blasius solution for laminar boundary layers as:
δ ≈ 5.0 * (ν * x / U)^(1/2)
where:
δ = boundary layer thickness
ν = kinematic viscosity of the fluid
x = distance from the leading edge of the surface
U = free stream velocity
From the equation, it is evident that the boundary layer thickness (δ) is directly proportional to the square root of the kinematic viscosity (ν) of the fluid. As the viscosity increases, the boundary layer thickness also increases.
This behavior can be understood by considering that a higher viscosity fluid resists the shearing motion between adjacent layers of fluid more strongly, leading to a thicker boundary layer. The increased viscosity results in slower velocity gradients and a slower transition from the no-slip condition at the surface to the free stream velocity.
Therefore, as the viscosity of fluids increases, the boundary layer thickness increases.
To know more about viscosity, click here:
https://brainly.com/question/30640823
#SPJ11
1 kmol/s of methane (CH4, MW = 16 kg/kmol) is burned in 20% excess air (fuel and air starting at 25°C), allowing for complete combustion and conversion of all of the methane. The water produced is in the vapor state. a) In the space below, write the balanced reaction for this system, including all species present. b) How much heat is released by this combustion reaction, in kJ per kmol of methane burned? c) If the reactor is adiabatic, what is the exiting temperature (K) of the product gas mixture? You may assume cp = 4Ru for all gases.
The heat released by the combustion of 1 kmol of methane is approximately -802.2 kJ, and the exiting temperature of the product gas mixture, in an adiabatic reactor, is approximately 0.69°C.
a) The balanced reaction for the combustion of methane with excess air is:
CH4 + 2(O2 + 3.76N2) -> CO2 + 2H2O + 7.52N2
b) To calculate the heat released by the combustion reaction, we can use the heat of formation values for each compound involved. The heat released can be calculated as follows:
Heat released = (ΣΔHf(products)) - (ΣΔHf(reactants))
ΔHf refers to the heat of formation.
Given the heat of formation values:
ΔHf(CH4) = -74.9 kJ/mol
ΔHf(CO2) = -393.5 kJ/mol
ΔHf(H2O) = -241.8 kJ/mol
ΔHf(N2) = 0 kJ/mol
ΔHf(O2) = 0 kJ/mol
Calculating the heat released:
Heat released = [1 * ΔHf(CO2) + 2 * ΔHf(H2O) + 7.52 * ΔHf(N2)] - [1 * ΔHf(CH4) + 2 * (0.2 * ΔHf(O2) + 0.2 * 3.76 * ΔHf(N2))]
Heat released = [1 * -393.5 kJ/mol + 2 * -241.8 kJ/mol + 7.52 * 0 kJ/mol] - [1 * -74.9 kJ/mol + 2 * (0.2 * 0 kJ/mol + 0.2 * 3.76 * 0 kJ/mol)]
Heat released ≈ -802.2 kJ/mol
Therefore, the heat released by the combustion reaction is approximately -802.2 kJ per kmol of methane burned.
c) Since the reactor is adiabatic, there is no heat exchange with the surroundings. Therefore, the heat released by the combustion reaction is equal to the change in enthalpy of the product gas mixture.
Using the equation:
ΔH = Cp * ΔT
where ΔH is the change in enthalpy, Cp is the heat capacity at constant pressure, and ΔT is the change in temperature, we can rearrange the equation to solve for ΔT:
ΔT = ΔH / Cp
Given that Cp = 4Ru for all gases, where Ru is the gas constant (8.314 J/(mol·K)), we can substitute the values:
ΔT = (-802.2 kJ/mol) / (4 * 8.314 J/(mol·K))
ΔT ≈ -24.31 K
The exiting temperature of the product gas mixture is the initial temperature (25°C) minus the change in temperature:
Exiting temperature = 25°C - 24.31 K
Exiting temperature ≈ 0.69°C (rounded to two decimal places)
Therefore, if the reactor is adiabatic, the exiting temperature of the product gas mixture is approximately 0.69°C.
Learn more about combustion
brainly.com/question/31123826
#SPJ11
Centre of Gravity i. What does the position of the centre of gravity (CG) affect? ii. Name at least two aircraft categories in which the CG is fixed. iii. Name at least three reasons/causes for the aircraft CG movement during flight operations.
i. The position of the center of gravity (CG) affects the stability and control of an aircraft.
ii. Two aircraft categories in which the CG is fixed are:
- Ultralight aircraft:
- Gliders:
iii. Three reasons/causes for the aircraft CG movement during flight operations are:
- Fuel consumption
- Payload changes
- Maneuvers
i. The position of the center of gravity (CG) affects the stability and control of an aircraft. It found how the aircraft will behave in flight, including its pitch, roll, and yaw characteristics.
ii. Two aircraft categories in which the CG is fixed are:
- Ultralight aircraft: These are small, single-seat aircraft that have a fixed CG. They are designed to be light and simple, with minimal controls and systems. The CG is typically located near the aircraft's wing, to ensure stable flight.
- Gliders: These are aircraft that are designed to fly without an engine. They rely on the lift generated by their wings to stay aloft. Gliders typically have a fixed CG, which is located near the front of the aircraft's wing. This helps to maintain stability during flight.
iii. Three reasons/causes for the aircraft CG movement during flight operations are:
- Fuel consumption: As an aircraft burns fuel during flight, its weight distribution changes, which affects the position of the CG. If the aircraft is not properly balanced, it can become unstable and difficult to control.
- Payload changes: When an aircraft takes on passengers, cargo, or other types of payload, the CG can shift. This is because the weight distribution of the aircraft changes.
- Maneuvers: During certain maneuvers, such as banking or pitching, the position of the CG can shift. This is because the forces acting on the aircraft change.
Learn more about the Centre of Gravity here;
https://brainly.com/question/1359722
#SPJ4
A body in uniaxial tension has a maximum principal stress of 20 MPa. If the body's stress state is represented by a Mohr circle, what is the circle's radius? a 20 MPa bb 5 MPa c 2 MPa d 10 MPa
The radius of the Mohr circle represents half of the difference between the maximum and minimum principal stresses. 10 MPa is the correct answer
The radius of a Mohr circle represents the magnitude of the maximum shear stress. In uniaxial tension, the maximum shear stress is equal to half of the difference between the maximum and minimum principal stresses. Since the maximum principal stress is given as 20 MPa, the minimum principal stress in uniaxial tension is zero.
In this case, the maximum principal stress is given as 20 MPa. Since the stress state is uniaxial tension, the minimum principal stress is zero.
Therefore, the radius of the Mohr circle is:
Radius = (σ₁ - σ₃) / 2
Since σ₃ = 0, the radius simplifies to:
Radius = σ₁ / 2
Substituting the given value of σ₁ = 20 MPa, we have:
Radius = 20 MPa / 2 = 10 MPa
Therefore, the radius of the Mohr circle representing the body's stress state is 10 MPa.
Option (d) 10 MPa is the correct answer.
To know more about Mohr circle visit:
https://brainly.com/question/31642831
#SPJ11