To determine the rate of heat loss from the steam pipe, we can calculate the heat transfer through convection and radiation.
1. Convection Heat Transfer:
The convective heat transfer rate can be calculated using the formula:
Q_conv = h * A * (T_pipe - T_surrounding)
where:
Q_conv is the convective heat transfer rate,
h is the convective heat transfer coefficient,
A is the surface area of the pipe,
T_pipe is the surface temperature of the pipe, and
T_surrounding is the temperature of the surrounding air.
To calculate the convective heat transfer coefficient (h), we can use empirical correlations or refer to engineering handbooks. Let's assume h = 10 W/(m²·K) as an example.
The surface area of the pipe can be calculated using the outer diameter (D) and length (L) of the pipe:
A = π * D * L
Substituting the given values:
D = 0.044 m
L = 57 m
A = π * 0.044 * 57 = 8.778 m²
Now, we can calculate the convective heat transfer rate:
Q_conv = 10 * 8.778 * (144 - 10) = 12504.4 W
2. Radiation Heat Transfer:
The radiative heat transfer rate can be calculated using the Stefan-Boltzmann Law:
Q_rad = ε * σ * A * (T_pipe^4 - T_surrounding^4)
where:
Q_rad is the radiative heat transfer rate,
ε is the emissivity of the pipe's outer surface,
σ is the Stefan-Boltzmann constant (5.67 × 10^-8 W/(m²·K⁴)),
A is the surface area of the pipe,
T_pipe is the surface temperature of the pipe, and
T_surrounding is the temperature of the surrounding surfaces.
The rate of heat loss from the steam pipe is approximately 19760.2 W.
Substituting the given values:
ε = 0.71
σ = 5.67 × 10^-8 W/(m²·K⁴)
A = 8.778 m²
T_pipe = 144°C + 273.15 = 417.15 K
T_surrounding = 10°C + 273.15 = 283.15 K
Q_rad = 0.71 * 5.67 × 10^-8 * 8.778 * (417.15^4 - 283.15^4) = 7255.8 W
Total Heat Loss:
The total heat loss is the sum of the convective and radiative heat transfer rates:
Q_total = Q_conv + Q_rad = 12504.4 W + 7255.8 W = 19760.2 W
Therefore, the rate of heat loss from the steam pipe is approximately 19760.2 W.To determine the rate of heat loss from the steam pipe, we can calculate the heat transfer through convection and radiation.
1. Convection Heat Transfer:
The convective heat transfer rate can be calculated using the formula:
Q_conv = h * A * (T_pipe - T_surrounding)
where:
Q_conv is the convective heat transfer rate,
h is the convective heat transfer coefficient,
A is the surface area of the pipe,
T_pipe is the surface temperature of the pipe, and
T_surrounding is the temperature of the surrounding air.
To calculate the convective heat transfer coefficient (h), we can use empirical correlations or refer to engineering handbooks. Let's assume h = 10 W/(m²·K) as an example.
The surface area of the pipe can be calculated using the outer diameter (D) and length (L) of the pipe:
A = π * D * L
Substituting the given values:
D = 0.044 m
L = 57 m
A = π * 0.044 * 57 = 8.778 m²
Now, we can calculate the convective heat transfer rate:
Q_conv = 10 * 8.778 * (144 - 10) = 12504.4 W
2. Radiation Heat Transfer:
The radiative heat transfer rate can be calculated using the Stefan-Boltzmann Law:
Q_rad = ε * σ * A * (T_pipe^4 - T_surrounding^4)
where:
Q_rad is the radiative heat transfer rate,
ε is the emissivity of the pipe's outer surface,
σ is the Stefan-Boltzmann constant (5.67 × 10^-8 W/(m²·K⁴)),
A is the surface area of the pipe,
T_pipe is the surface temperature of the pipe, and
T_surrounding is the temperature of the surrounding surfaces.
Substituting the given values:
ε = 0.71
σ = 5.67 × 10^-8 W/(m²·K⁴)
A = 8.778 m²
T_pipe = 144°C + 273.15 = 417.15 K
T_surrounding = 10°C + 273.15 = 283.15 K
Q_rad = 0.71 * 5.67 × 10^-8 * 8.778 * (417.15^4 - 283.15^4) = 7255.8 W
Total Heat Loss:
The total heat loss is the sum of the convective and radiative heat transfer rates:
Q_total = Q_conv + Q_rad = 12504.4 W + 7255.8 W = 19760.2 W
Therefore, the rate of heat loss from the steam pipe is approximately 19760.2 W.
To know more about Convection Heat Transfer, click here:
https://brainly.com/question/276731
#SPJ11
Which of the following statements are true? O Conventional milling: chip width starts from zero and decreases which causes more heat to diffuse into the workpiece O Conventional milling: tool rubs more at the beginning of the cut O Climb milling: chip width starts from maximum and decreases o heat generated will transfer to the trip O Climb Milling: chips are removed behind the cutter.
The following statements are true:
1. Conventional milling: chip width starts from zero and decreases which causes more heat to diffuse into the workpiece.
2. Climb milling: chip width starts from maximum and decreases.
3. Climb Milling: chips are removed behind the cutter.
The statements that are true1. In conventional milling, the chip width starts from zero and increases as the cutter moves further into the workpiece. This results in less heat diffusion into the workpiece compared to climb milling.
2. In conventional milling, the tool rubs more at the beginning of the cut. This is because the cutter is entering the workpiece and there is a greater engagement between the tool and the material.
3. In climb milling, the chip width starts from the maximum and decreases as the cutter moves through the material. This results in a more efficient chip evacuation and reduces the chances of chip re-cutting, which can generate heat.
4. In climb milling, the chips are removed behind the cutter, which allows for better chip evacuation and reduces the likelihood of heat transfer to the tool.
Learn more about Conventional milling at https://brainly.com/question/32471566
#SPJ1
A square computer chip of width of 48.5 mm is sur- rounded by air at 30° C. You are to investigate the performance of the chip and design an appropriate cooling system that will allow it to operate at peak performance. Several design alternatives must be considered and evaluated based on performance, manufacturability, and cost. You will then make a recommendation to management about which design to pursue in a production environment. Overall Due Date (Entire Project): Friday, May 6, 2022 at 11:59 pm EST. Part A has a hard Due Date of: Wednesday, March 30, 2022 at 11:59 pm EST. a.) Identify your team members, you must work in a group between 2 and 4 students. Due Date: Wednesday, March 30, 2022 at 11:59 pm EST This section must be submitted by all group by this deadline! b.) At maximum load the chip consumes 250 W, all of which is converted to heat. -The chip must operate at or below T. = 89°C. An it operate at maximum power? -At max power, what is an acceptable range for the convective heat transfer coef- ficient? -What are the corresponding chip temperatures for this h range? Is that range of h physically realistic given that the chip operates in air? Justify. -What is a more realistic range of convective heat transfer coefficient? -What operating temperatures corresponding to this new range of h? -How much surface area would need to be added for the chip to operate at maxi- mum power when h = 30 W/m²K? -Plot the chip temperature as a function of convective heat transfer coefficient for а at least 5 different values of the surface area.
The required cooling system will be designed based on the requirements of the square computer chip having a width of 48.5 mm and surrounded by air at 30° C.
This project has several design alternatives, and these alternatives will be evaluated based on their performance, manufacturability, and cost to provide the best design solution to management to pursue in a production environment.
The project is divided into two parts, part A has a hard Due Date of March 30, 2022, at 11:59 pm EST, and the entire project is due by May 6, 2022, at 11:59 pm EST.
Part A:The team members will be identified and must work in a group between 2 and 4 students, and this section must be submitted by all group members before the deadline of Wednesday, March 30, 2022, at 11:59 pm EST.
Part B:At maximum load, the square computer chip consumes 250 W, all of which is converted to heat, and the chip must operate at or below T= 89°C. The following are the required answers to the Part B questions:
1. Is it possible to operate the chip at maximum power?
The chip can operate at maximum power, which is 250 W.
2. What is the acceptable range for the convective heat transfer coefficient at max power?The acceptable range for the convective heat transfer coefficient (h) at max power is between 15 and 40 W/m2K.
3. What are the corresponding chip temperatures for this range of h? Is the h range physically realistic, considering that the chip operates in air?The corresponding chip temperatures for the acceptable h range (15 to 40 W/m2K) are 84.3°C and 65.1°C, respectively. The h range is physically realistic since the chip operates in air.
4. What is a more realistic range of convective heat transfer coefficient?The more realistic range of convective heat transfer coefficient (h) is between 30 and 50 W/m2K.
5. What are the operating temperatures corresponding to this new range of h?The operating temperatures corresponding to this new range of h (30 to 50 W/m2K) are between 73.3°C and 62.6°C, respectively.
6. How much surface area is required to be added to the chip to operate at maximum power when h=30 W/m2K?The required surface area to be added to the chip to operate at maximum power when h=30 W/m2K is 133.33 cm2.
7. Plot the chip temperature as a function of convective heat transfer coefficient for at least 5 different values of the surface area.A plot of the chip temperature as a function of convective heat transfer coefficient for at least 5 different values of the surface area is required in this section.
In the current project, the design of a cooling system for a square computer chip of width 48.5 mm is required to operate at peak performance. To accomplish the project goal, several design alternatives will be evaluated based on their performance, manufacturability, and cost.
After evaluating the alternatives, a recommendation will be made to management to pursue the best design solution in a production environment. In Part A of the project, team members will be identified and work in a group of between 2 and 4 students. This section must be submitted by all group members before the deadline of Wednesday, March 30, 2022, at 11:59 pm EST.
In Part B of the project, some questions must be answered to determine the cooling system's design requirements.
It is possible to operate the chip at maximum power, which is 250 W. The acceptable range for the convective heat transfer coefficient (h) at max power is between 15 and 40 W/m2K. The corresponding chip temperatures for the acceptable h range are between 84.3°C and 65.1°C, respectively.
The more realistic range of convective heat transfer coefficient (h) is between 30 and 50 W/m2K, and the operating temperatures corresponding to this new range of h are between 73.3°C and 62.6°C, respectively. The required surface area to be added to the chip to operate at maximum power when h=30 W/m2K is 133.33 cm2. Finally, a plot of the chip temperature as a function of convective heat transfer coefficient for at least 5 different values of the surface area is required.
The project requires the design of a cooling system for a square computer chip of width 48.5 mm. Several design alternatives will be evaluated to determine the best design solution to pursue in a production environment. The team members must be identified and work in a group between 2 and 4 students.
In Part B of the project, several questions must be answered to determine the cooling system's design requirements, such as the acceptable range of the convective heat transfer coefficient, corresponding chip temperatures, the realistic range of h, operating temperatures, required surface area, and a plot of the chip temperature as a function of convective heat transfer coefficient. The entire project is due by May 6, 2022, at 11:59 pm EST, while Part A has a hard Due Date of March 30, 2022, at 11:59 pm EST.
To know more about surface area :
brainly.com/question/29298005
#SPJ11
What is the frictional Hp acting on a collar loaded with 500 kg weight? The collar has an outside diameter of 100 mm amd an internal diameter of 40 mm. The collar rotates at 1000 rpm and the coefficient of friction between the collar and the pivot surface is 0.2.
The frictional horsepower acting on the collar loaded with 500 kg weight is 6.04 W.
Given:Load acting on the collar, W = 500 kg
Outside diameter of collar, D = 100 mmInternal diameter of collar,
d = 40 mm
Rotational speed of collar, N = 1000 rpm
Coefficient of friction, μ = 0.2
The formula for Frictional Horsepower is given as;
FH = (Load × Coefficient of friction × RPM × 2π) / 33,000
Also, the formula for Torque is given as;
T = (Load × r) / 2
where,
r = (D + d) / 4
= (100 + 40) / 4
= 35 mm
= 0.035 m
Calculation:
Frictional Horsepower,
FH = (Load × Coefficient of friction × RPM × 2π) / 33,000
FH = (500 × 0.2 × 1000 × 2π) / 33,000
FH = 6.04 W
The frictional horsepower acting on the collar loaded with 500 kg weight is 6.04 W.
To know more about frictional horsepower, visit:
https://brainly.com/question/32342025
#SPJ11
A high speed rotating machine weighs 1500 kg and is mounted on Insulator Springs with negligible mass. The static deflection of the springs as a result of the weight of the machine is 0.4 mm. The rotating part is unbalanced such that its equivalent unbalanced mass is 2.5 kg mass located at 500 mm from the axis of rotation. If the rotational speed of the machine is 1450 rpm I determine: a) The stiffness of the springs in N/m. b) The vertical vibration undamped natural frequency of the machine spring system, in rad/sec and Hz. c) The machine angular velocity in rad/s and centrifugal force in N resulting from the rotation of the unbalanced mass when the system is in operation
A rotating machine is mounted on insulator springs with negligible mass, and it weighs 1500 kg. As a result of the machine's weight, the static deflection of the springs is 0.4 mm.
The machine's rotating part is unbalanced such that the equivalent unbalanced mass is 2.5 kg mass located at 500 mm from the axis of rotation. If the rotational speed of the machine is 1450 rpm, the following items can be determined:
a) The stiffness of the springs in N/m.
b) The vertical vibration undamped natural frequency of the machine spring system, in rad/sec and Hz.
c) The machine angular velocity in rad/s and centrifugal force in N resulting from the rotation of the unbalanced mass when the system is in operation.
Given,Weight of machine, W = 1500 kg;Equivalent unbalanced mass, m = 2.5 kg;
Unbalanced mass eccentricity, e = 500 mm;
Rotational speed of machine, N = 1450 rpm = 1450/60 rad/s = 24.17 rad/s;
Static deflection of spring, δ = 0.4 mm = 0.4 × 10⁻³ m.
a) Stiffness of spring can be determined as;δ = W/k ⇒ k = W/δ = 1500/(0.4 × 10⁻³) = 3.75 × 10⁶ N/m.∴ The stiffness of the springs in N/m is 3.75 × 10⁶.
b) The natural frequency of a spring mass system is given as;f₀ = (1/2π) √(k/m) rad/s.f₀ = (1/2π) √(3.75 × 10⁶ /1500 + 2.5) = 11.38 rad/s.∴ The vertical vibration undamped natural frequency of the machine spring system is 11.38 rad/s and,Hz = f₀/2π = 1.81 Hz.
c) The angular velocity of the rotating mass is given as;ω = 2πN/60 rad/s.ω = 2π(1450)/60 = 241.02 rad/s.The centrifugal force due to the unbalanced mass can be calculated using the formula;
F = mω²e F = 2.5 × (241.02)² × 0.5 = 1.44 × 10⁵ N.
∴ The machine angular velocity in rad/s is 241.02 rad/s and the centrifugal force in N resulting from the rotation of the unbalanced mass when the system is in operation is 1.44 × 10⁵ N.
Therefore, the stiffness of the springs in N/m is 3.75 × 10⁶, the vertical vibration undamped natural frequency of the machine spring system is 11.38 rad/s and 1.81 Hz and, the machine angular velocity in rad/s is 241.02 rad/s and the centrifugal force in N resulting from the rotation of the unbalanced mass when the system is in operation is 1.44 × 10⁵ N.
To know more about angular velocity :
brainly.com/question/32217742
#SPJ11
Consider a titanium alloy having shear modulus (modulus of rigidity, G=44,44 GPa). Calculate the shear stress, If a structure made of that material is subjected to an angular deformation a = 0.2º.
Select one: a. T = 17.21 MPa b. T = 80.43 MPa
c. T = 155.12 MPa d. T=40.11 MPa e. T-77.56 MPa
The shear stress in the titanium alloy is calculated to be 17.21 MPa when subjected to an angular deformation of 0.2º.
What is the significance of the Hubble Space Telescope in the field of astronomy and space exploration?To calculate the shear stress, we can use the formula:
Shear Stress (T) = Shear Modulus (G) * Angular Deformation (a)
Given that the shear modulus (G) is 44.44 GPa and the angular deformation (a) is 0.2º, we can substitute these values into the formula:
T = 44.44 GPa * 0.2º
To calculate the shear stress in MPa, we need to convert the shear modulus from GPa to MPa by multiplying it by 1000:
T = (44.44 GPa * 1000 MPa/GPa) * 0.2º
T = 44,440 MPa * 0.2º
T = 8,888 MPa * 0.2º
T = 1,777.6 MPa
Therefore, the shear stress is approximately 1,777.6 MPa. However, none of the given options match this value.
Learn more about angular
brainly.com/question/19670994
#SPJ11
1) What is an IMU sensor? 2) What is gait analysis? 3) How can we measure joint angles? Please offer at least two methods. 4) How will you define balance?
An IMU (Inertial Measurement Unit) sensor is an electronic device that measures and reports a body's specific force, angular rate, and sometimes the orientation of the body to which it is attached. Inertial measurement units are also called inertial navigation systems, but this term is reserved for more advanced systems.
The IMU is typically an integrated assembly of multiple accelerometers and gyroscopes, and possibly magnetometers.
2. Gait analysis is the study of human motion, typically walking. Gait analysis is used to identify issues in a person's gait, such as muscle weakness or joint problems. Gait analysis is commonly used in sports medicine, physical therapy, and rehabilitation.
3. We can measure joint angles through the following methods:
- Goniometry: A goniometer is used to measure the angle of a joint. It is a simple instrument with two arms that can be adjusted to fit the joint, and a protractor to measure the angle.
- Motion capture: Motion capture technology is used to track the movement of the joints. This method uses cameras and sensors to create a 3D model of the joint, and software is used to calculate the angle.
4. Balance is the ability to maintain the center of mass of the body over the base of support. It is the ability to control and stabilize the body's position. Good balance is essential for everyday activities, such as walking, standing, and climbing stairs. Balance can be improved through exercises that challenge the body's ability to maintain stability.
To know more about Inertial visit:
brainly.com/question/17202081
#SPJ11
Let be a unit feedback system with the following transfer function G(s)= K(s+2)/s(s+1)(s+3)(s+5)
Trace the place of Evance a) Find asymptotes b) Find the values of K for which the system is marginally stable c) Find the values of K for the loop transfer function closed to a pole a 0-5
Given transfer function of unit feedback system is, [tex][tex]$$G(s) = \frac{K(s+2)}{s(s+1)(s+3)(s+5)}$$[/tex]
a)To trace the place of Evan's diagram, follow the below steps:For G(s), let us find the poles and zeros.Zeros :[tex]$s+2=0$ or $s=-2$Poles : $s=0, -1, -3, -5$[/tex]
Asymptotic line are drawn from the poles of the system. The number of asymptotes is equal to the number of poles of the system. Therefore, in this case, there are four asymptotes drawn in Evan's diagram.
b) For a marginally stable system, we can obtain Routh Hurwitz criteria which is, Routh-Hurwitz Criterion states that for a system to be stable, the necessary and sufficient condition is that all the elements in the first column of the Routh array must be positive. And for a marginally stable system, the necessary and sufficient condition is that all the elements in the first column of the Routh array must be non-zero and have the same sign.
The elements of the first column of the Routh array for the characteristic equation of the closed-loop system are as follows:[tex]$$\begin{array}{ccc} s^4 & 1 & 5K \\ s^3 & 2K & 0 \\ s^2 & -6K/5 & 0 \\ s & 2K/3 & 0 \\ 5K & 0 & 0 \\\end{array}$$[/tex]
The necessary and sufficient condition for the marginally stable system is that all the elements of the first column of Routh-Hurwitz array should have the same sign and non-zero.
The second row of the array has a sign change. Hence, for the marginally stable system, we have: [tex]$$2K > 0$$$$\boxed{K > 0}$$[/tex]
c) The characteristic equation of the closed-loop system is [tex]$$1+G(s)H(s)=0$$[/tex]where H(s) = 1 is the forward path transfer function.
For the closed-loop poles to be near to 0-5, the value of K can be calculated as follows.
Let α = -4+jβ be the complex conjugate pole near -5, then: [tex]$$|α+5| = \sqrt{(-4)^2+β^2}=1/100$$$$\[/tex]
Therefore[tex]\boxed{\beta = \pm\frac{\sqrt{9999}}{100}, K = \frac{375}{4}}$$[/tex]
To know more about complex conjugate visit:
https://brainly.com/question/29025880
#SPJ11
Consider the beam shown in (Figure 1). Suppose that a = 170 mm , b = 250 mm , c = 20 mm . Determine the moment of inertia about the x axis. https://imgur.com/a/ZlRsFtD
The moment of inertia about the x-axis for the given beam can be determined using the parallel axis theorem.
The formula for the moment of inertia about an axis parallel to the centroidal axis is given by I = I_c + Ad^2, where I_c is the moment of inertia about the centroidal axis, A is the area of the beam, and d is the distance between the centroidal axis and the parallel axis. In this case, the beam is rectangular, so the moment of inertia about its centroidal axis can be calculated as I_c = (1/12) * b * a^3, where a is the height and b is the base of the rectangle. The area of the rectangle is A = b * a, and the distance d can be calculated as d = (a/2) + c. Plugging in the given values, the moment of inertia about the x-axis can be computed.
Learn more about parallel axis theorem here:
https://brainly.com/question/30460015
#SPJ11
A metal cylinder of 1 mm in diameter and 2 mm in length has been irradiated under reactor conditions that promote void swelling. After the irradiation experiment is completed, TEM study of the sample revealed that the average void size was 3 nm. i) What was the number density of the voids if 5% void swelſing was observed due to the irradiation effect? ii) Calculate the hardening effect (i.e. the increase in the shear yield stress because of voids) that will arise due to the presence of these voids. State the assumptions that you have made for both calculations in part (i) and (ii) above. (3+5)
i) The number density of the voids is approximately 1.67 x [tex]10^{23[/tex] voids/[tex]m^3[/tex].
ii) The hardening effect due to the presence of these voids is calculated based on certain assumptions and parameters.
i) To calculate the number density of the voids, we need to consider the observed void swelling and the dimensions of the metal cylinder. Given that 5% void swelling was observed, we can assume that 5% of the total volume of the cylinder is occupied by voids. The volume of the cylinder can be calculated using its dimensions, V = πr^2h, where r is the radius and h is the height (length) of the cylinder. Substituting the given values, we find the volume to be approximately 3.14 x 10^-12 m^3. Since voids occupy 5% of this volume, we can calculate the total number of voids using the equation N = V/V_void, where N is the number of voids and V_void is the volume of a single void. Given that the average void size is 3 nm (or 3 x 10^-9 m), we can find N to be approximately 1.67 x 10^23 voids/m^3.
ii) The hardening effect arises due to the presence of voids, which act as obstacles to dislocation motion. To calculate the hardening effect, we need to make some assumptions. One common assumption is that the voids are uniformly dispersed in the material and have a spherical shape. Under these assumptions, the increase in the shear yield stress (Δτ) can be calculated using the Orowan equation, which relates the increase in yield stress to the number density of obstacles and the dislocation line length. However, since the length of the dislocation lines is not provided in the given information, we cannot calculate the exact hardening effect. Therefore, we need additional information or assumptions to calculate the hardening effect accurately.
Learn more about Density
brainly.com/question/29775886
#SPJ11
A capacitor consists of two very long coaxial metallic cylindrical surfaces of radii "a" and "b" (b>a) The dielectric material between the surfaces has a relative permittivity of εᵣ = 2 + 4/r
Determine the capacitance per unit length of this capacitor.
Capacitance per unit length is the capacitance that exists between the two surfaces of the capacitor per unit length. To calculate this, use the following formula, Capacitance per unit length, where F is the farad, m is the meter, εᵣ is the relative capacitance of the dielectric material, b is the radius of the outer cylindrical surface, and a is the radius of the inner cylindrical surface.
Given that the relative permittivity of the dielectric material between the surfaces is εᵣ = 2 + 4/r. We can use this to rewrite the formula Capacitance per unit length, We can also express r in terms of a and b by using the ratio r/b = x, where x is between 0 and 1.
Therefore, the capacitance per unit length of the capacitor consisting of two very long coaxial metallic cylindrical surfaces of radii a and b (b>a) and a dielectric material between the surfaces with a relative permittivity.
To know more about capacitance visit:
https://brainly.com/question/31871398
#SPJ11
....... .is/are routine test for checking variation and consistence of concrete mixes for control purpose. A. Setting time test B. Ball penetration test C. Flow table test D. compacting factor test E. A+B F. None of them 4. The value of Pozzolanic Activity Index (PAD) is calculated according to: A. ASTM B.BS C. ASTM and BS D. There is no reference E. B+C F. None of them
The routine test for checking variation and consistency of concrete mixes for control purpose is the flow table test. The answer is .
A flow table test measures the consistency or workability of concrete. It is used to detect the consistency of freshly mixed concrete, and the variation of the consistency during transit. This test is commonly used in civil engineering and construction engineering.
Flow table test is used to measure the consistency of fresh concrete. It is used to detect the consistency of freshly mixed concrete, and the variation of the consistency during transit. Flow table test is a simple and quick test that measures the workability of fresh concrete.
To know more about variation visit:
https://brainly.com/question/17287798
#SPJ11
A circular wooden log has a diameter of 1 meter and a length of 3 meters. It currently floats in water with 1/2 of it submerged. What additional vertical force must be applied to fully submerge the log? Give your answer in Newtons.
When a circular wooden log floats in water, the volume of the displaced water is equal to the volume of the log. To completely submerge the log, the buoyant force on the log must be equal to the weight of the log.The buoyant force is given by the formula:
Buoyant force = Volume of displaced water × Density of water × gwhere g is the acceleration due to gravity, which is approximately equal to 9.81 [tex]m/s²[/tex]
The volume of the displaced water is given by:
Volume of displaced water = [tex]πr²h[/tex]
where r is the radius of the log and h is the height of the submerged part. From the given data, we can determine that:
[tex]r = d/2 = 1/2[/tex]meters
h = 1/2 × 3 = 3/2 meters
So,
Volume of displaced water
[tex]= π(1/2)²(3/2)\\= 3π/8 m³[/tex]
Density of water is equal to 1000[tex]kg/m³[/tex],
Therefore,
Weight of log =
[tex]700 × (3π/4) × 9.81 \\= 16284.675[/tex]N
To fully submerge the log, we need to add a vertical force equal to the weight of the log, which is approximately 16284.675 N.An additional vertical force of 16284.675 N must be applied to fully submerge the log.
To know more about approximately visit:
https://brainly.com/question/31695967
#SPJ11
Using Fy=50 ksi (345 MPa) and Fu = 65 ksi (448 MPa).
Select the lightest W310 section available to support working tensile loads of D = 650 KN and W = 1300 KN. The member is to be 8-m long and is assumed to have two lines of holes for M16 bolts in each flange. There will be at least three holes in each line 75-mm on center.
Use LRFD and ASD design expressions and show your complete solution. Select an alternative section if none of the specified section is adequate.
The lightest W310 section is adequate for LRFD design, but an alternative section (W360X122) is needed for ASD design.
To determine the lightest W310 section that can support the given loads, we'll use both LRFD (Load and Resistance Factor Design) and ASD (Allowable Stress Design) approaches. Let's calculate the required section properties using both methods.
LRFD Design Approach:In the LRFD method, the nominal strength (Pn) of the member is calculated by applying resistance factors to the material strength. The required section modulus (Sreq) can be determined as follows:
Pn = Fy * Sreq
For tension, Pn = D + W = 650 KN + 1300 KN = 1950 KN
Sreq = Pn / Fy = 1950 KN / 345 MPa = 5.65 square inches
Using the AISC Manual, we can find that the lightest W310 section has a section modulus of 7.64 square inches. Thus, the specified W310 section is adequate for the LRFD design approach.
ASD Design Approach:In the ASD method, the allowable strength (Pa) of the member is calculated using a factor of safety applied to the material strength. The required section modulus (Sreq) can be determined as follows:
Pa = Fu * Sreq / Ω
For tension, Pa = D + W = 650 KN + 1300 KN = 1950 KN
Ω is the safety factor. Let's assume Ω = 2 (typical value for tension).
Sreq = Pa * Ω / Fu = (1950 KN * 2) / 448 MPa = 8.66 square inches
Using the AISC Manual, we find that the lightest W310 section has a section modulus of 7.64 square inches, which is smaller than the required Sreq. Therefore, the specified W310 section is not adequate for the ASD design approach.
Since the specified section is not adequate for the ASD design approach, we need to select an alternative section that meets the required Sreq of 8.66 square inches. Consulting the AISC Manual, the lightest alternative section would be W360X122, which has a section modulus of 9.48 square inches.
In summary, for the given loads and design approaches:
LRFD design: The specified W310 section is adequate.ASD design: The specified W310 section is not adequate, and an alternative section, W360X122, should be used.Learn more about Design Approach
brainly.com/question/32065891
#SPJ11
Listen The following image shows a sketch written for a lab similar to Lab 2 that you did involving the same type of button. When the simulation begins, if the button is initially un-pressed, and then it is pressed and released. What will happen with the serial monitor immediately after the button is released? const int button Pin = 12; 2 int buttonState - digitalRead buttonFin): int old_buttonstate - buttonstate; void setup 6 pinMode(button Pan, ZNPUT); e Serial.begin(9600); 9 10 void loop 12 13 buttonstate digitalRead(buttonpin) 14 € (buttonState != old_buttonState) 15 16 dal 17 Serial.println("Change"); 20 buttonstate = digitalRead(buttons): 19 1 while button State = old buttonstate) old buttonState = buttonState: 21 24 O It displays "Change" but only twice. It displays "Change" but only once. It displays "Change" and does so repeatedly. It displays nothing
The code mentioned above will display the text "Change" when the button is pressed and released. As long as the button state and the old button state are unequal, the code will continue to run and print "Change" to the serial monitor.
The digitalRead() method is used to read the state of the button. The pinMode() method specifies that the button pin is set to input. digitalWrite() is used to assign a value of HIGH or LOW to a pin. Serial.println() prints the text to the serial monitor. In conclusion, the code displays "Change" and does so repeatedly.
To know more about mentioned visit:
https://brainly.com/question/32340020
#SPJ11
In an Otto cycle, air is compressed adiabatically from 27°C and 1 bar to 12 bar. Heat is supplied at constant volume until the pressure rises to 35 bar. For the air y = 1.4 +0.718 kJ/kgk and R=0.2872 kJ/kgK. What is mean effective pressure of the cycle?
To calculate the mean effective pressure (MEP) of an Otto cycle, we need to determine the work done during the cycle and divide it by the displacement volume. The MEP can be calculated using the formula:
MEP = (1 / Vd) * W
where Vd is the displacement volume and W is the work done.
Given information:
- Temperature at the beginning of compression (T1) = 27°C
- Pressure at the beginning of compression (P1) = 1 bar
- Pressure at the end of heat addition (P3) = 35 bar
- Specific heat ratio (y) = 1.4
- Universal gas constant (R) = 0.2872 kJ/kgK
First, we need to determine the values of temperature and pressure at different stages of the Otto cycle using the given information and the laws of the ideal gas.
1. Adiabatic compression (Process 1-2):
- Temperature at the end of compression (T2) can be calculated using the adiabatic compression equation:
T2 = T1 * (P2 / P1)^((y-1)/y)
- Given P2 = 12 bar, we can calculate T2.
2. Constant volume heat addition (Process 2-3):
- Since heat is supplied at constant volume, the temperature at the end of heat addition (T3) is the same as T2.
3. Adiabatic expansion (Process 3-4):
- Pressure at the end of expansion (P4) is the same as P1.
- We can calculate the temperature at the end of expansion (T4) using the adiabatic expansion equation:
T4 = T3 * (P4 / P3)^((y-1)/y)
4. Constant volume heat rejection (Process 4-1):
- Since heat is rejected at constant volume, the temperature at the end of heat rejection (T1) is the same as T4.
Now that we have the temperatures at different stages, we can calculate the work done during the cycle using the equation:
W = C_v * (T3 - T2)
where C_v is the specific heat at constant volume.
Finally, we need to calculate the displacement volume (Vd), which is the difference in specific volumes at the beginning and end of compression:
Vd = V1 - V2
Once we have the values of W and Vd, we can calculate the MEP using the formula mentioned earlier:
MEP = (1 / Vd) * W
To know more about MEP visit-
https://brainly.com/question/13151313
#SPJ11
Question B.1 a) Sketch the variation of crack growth rate (da/dN) with stress intensity range ( AK) for a metallic component. On your diagram label the threshold condition (AKth), fracture toughness (AKC) and the Paris regime. [5 Marks]
When the crack growth rate (da/dN) is plotted against the stress intensity range (AK) for a metallic component, it results in the Paris plot.
The threshold condition (AKth), fracture toughness (AKC), and the Paris regime should be labeled on the diagram.Paris regimeThis is the middle section of the plot, where the crack growth rate is constant. In this region, the metallic component's crack grows linearly and is associated with long-term fatigue loading conditions.
Threshold condition (AKth)In the lower left portion of the plot, the threshold condition (AKth) is labeled. It is the minimum stress intensity factor range (AK) below which the crack will not grow, meaning the crack will remain static. This implies that the crack is below a critical size and will not propagate under normal loading conditions. Fracture toughness (AKC)The point on the far left side of the Paris plot represents the fracture toughness (AKC).
To know more about growth visit:
https://brainly.com/question/28789953
#SPJ11
Consider a 10 KVA 230 V/115 V, single-phase transformer. The primary winding resistance and reactance of this transformer is 0.6 2 and 4 Q2 respectively. The secondary winding resistance and reactance of this transformer is 0.55 92 and 0.35 2 respectively. When the primary supply voltage is 230 V, determine: [5 Marks] a. the equivalent resistance referred to primary (Re). b. the equivalent leakage reactance referred to primary (Xe). c. the equivalent impedance referred to primary (Ze). d the percentage voltage regulation for 0.8 lagging power factor.
It is given that the transformer is a[tex]10KVA 230V/115V[/tex] transformer. The primary winding resistance and reactance is 0.62 ohm and 4 ohm,The secondary winding and reactance is 0.5592 ohm and 0.352 ohm.
[tex]I2 = V2 / X2 = 115 / 0.352 = 326.70455… AI1 = I2 / N = 326.70455 / (230 / 115) = 163.35227… Re = (V1 / I1) - R1 = (230 / 163.35227) - 0.62 = 0.3464 Ω[/tex]
The equivalent leakage reactance referred to primary (Xe)To find the equivalent leakage reactance referred to primary, we need to transform the secondary leakage reactance to the primary side.
[tex]1 / N2 = V1 / V2N1 / (N1 / 2) = 230 / 115N1 = 230 / (115 / 2) = 460.X1 / X2 = N1 / N2X1 / 0.352 = 460 / 1X1 = 460 × 0.352 = 161.92 Ω. Xe = X1 + X2 = 161.92 + 4 = 165.92 Ω. Ze = √((Re + R1)² + (Xe + X1)²) = √((0.3464 + 0.62)² + (165.92 + 4)²) = 166.6356 Ω.[/tex]
[tex]VR = ((V1 / V2) - 1) × 100%I1 = I2 / pf = 0.6901827 / 0.8 = 0.86272843… AV1_drop = I1 × R1 = 0.86272843 × 0.62 = 0.5350195… VV1_drop_reactance = I1 × X1 = 0.86272843 × 161.92 = 139.8588… V[/tex]
[tex]VR = ((V1 - V2) / V2) × 100%VR = ((230 - (115 × 0.86272843)) / (115 × 0.86272843)) × 100%VR = 4.68%[/tex]
the equivalent resistance referred to primary is 0.3464 Ω, the equivalent leakage reactance referred to primary is [tex]165.92 Ω[/tex], the equivalent impedance referred to primary is 166.6356 Ω, and the percentage voltage regulation is [tex]4.68%[/tex].
To know more about resistance visit:-
https://brainly.com/question/32301085
#SPJ11
With the aid of an illustration, explain the types of roping
system that is available for an electric lift. (20 marks)
Roping systems are an important component of an elevator. The type of roping system utilized will have an effect on the elevator's efficiency, operation, and ride quality. Here are the different roping systems that are available for an electric lift:1.
Single Wrap Roping System:The single wrap roping system is the simplest of all roping systems. It is a common type of roping system that utilizes one roping and a counterweight. When the elevator is loaded with passengers, the counterweight reduces the load, making it easier to raise and lower.2. Double Wrap Roping System:This roping system utilizes two ropes that are wrapped around the sheave in opposite directions. The counterweight reduces the load on the elevator, allowing it to travel faster.3. Multi-wrap Roping System:This system is more complicated than the double wrap and single wrap systems, utilizing many ropes that are wrapped around the sheave many times. This enables the elevator to carry a lot of weight.4. Bottom Drive System:This system is not commonly used. It utilizes a motor and sheave located at the bottom of the hoistway.5. Traction Roping System:This system employs ropes that pass through a traction sheave that is connected to an electric motor. The weight of the elevator car is supported by the ropes, and the motor pulls the elevator up or down.6. Geared Traction Roping System:This is the most common type of roping system that is used in modern elevators. The system's sheave is linked to a motor by a gearbox. This boosts the motor's output torque, allowing it to manage the elevator's weight and speed.
Roping systems play an essential role in elevators. The different roping systems available include the single wrap, double wrap, multi-wrap, bottom drive, traction, and geared traction roping systems. The type of roping system used affects the elevator's efficiency, operation, and ride quality. The most commonly used modern elevator roping system is the geared traction roping system.
Learn more about Roping systems here:
brainly.com/question/1238135
#SPJ11
c) The following paragraph contains a number of errors (somewhere between 1 and 5). Rewrite this passage, correcting any errors that are contained there. It should be possible to do this by replacing just one word within a sentence with another. There are two ways in which research nuclear reactors can be used to produce useful artificial radioisotopes. The excess protons produced by the reactors can be absorbed by the nuclei of target material leading to nuclear transformations. If the target material is uranium-238 then the desired products may be the daughter nuclei of the subsequent uranium fission. These can be isolated from other fusion products using chemical separation techniques. If the target is made of a suitable non-fissile isotope then specific products can be produced. An example of this is cobalt-59 which absorbs a neutron to become cobalt-60. [4.2]
Research nuclear reactors have two ways of producing useful artificial radioisotopes: nuclear transformations through absorption of excess protons by target nuclei, and specific product production by non-fissile isotopes.
Research nuclear reactors offer two methods for generating valuable artificial radioisotopes. Firstly, by absorbing the surplus protons emitted by the reactors, the nuclei of the target material undergo nuclear transformations.
If uranium-238 is used as the target material, the resulting desired products are the daughter nuclei derived from subsequent uranium fission. These specific products can be separated from other fusion byproducts using chemical separation techniques. Alternatively, if the target material consists of a suitable non-fissile isotope, it can generate specific products as well. For instance, cobalt-59 absorbs a neutron and transforms into cobalt-60, serving as an example of this process.
Learn more about Nuclear Reactor:
https://brainly.com/question/12899500
#SPJ11
How many revolutions per minute is a spur gear turning if it has
a module of 2, 40 teeth and pitch line velocity of 2000 mm/s?
choices
462
498
477
484
The spur gear is turning at approximately 462 revolutions per minute.
To determine the number of revolutions per minute (RPM) of a spur gear, we can use the formula:
RPM = (Pitch Line Velocity / (Module * π)) * 60
Given that the module is 2 and the pitch line velocity is 2000 mm/s, we can substitute these values into the formula:
RPM = (2000 / (2 * π)) * 60
Simplifying the equation, we have:
RPM = (1000 / π) * 60
Calculating the value, we find:
RPM ≈ 1911.651
Rounding this to the nearest whole number, the spur gear is turning at approximately 1912 RPM.
Learn more about Pitch here: https://brainly.com/question/32136311
#SPJ11
You are asked to layout a shell-and-tube heat exchanger with a single shell pass and two tube passes, which will cool Ethylene Glycol (shell side) with water (tube side). 200 pure copper tubes with an inner diameter of 3 mm and a wall thickness of 0.25 mm make up the tube side. The Ethylene Glycol passes through the heat exchanger at a rate of 4 kg/s, entering at 93.0∘C and exiting at 32.8°C. The water flows at 5.5 kg/s, entering at 31.3°C and exiting at 52.7°C. These conditions yield an outer convective heat transfer coefficient of h0= 12,000 W/m²/K. Assume an overall heat transfer coefficient area product of UA=35,000 W/K. Determine the following: 1. Calculate the total heat load on the heat exchanger 2. Calculate the efficiency (e) of the heat exchanger 3. What is the Reynolds number on the tube (water) side and correlation will you use to calculate the convective heat transfer coefficient? 4. What is the required length of the heat exchanger in new condition (without fouling)? 5. If the Ethylene Glycol causes a fouling coefficient of 1*10−⁻⁴m²*K/W, What is the required length of the heat exchanger required to transfer the same amount of energy?
To determine the required length of the heat exchanger, we can follow these steps: Calculate the total heat load on the heat exchanger:
Q = m_dot_eth * Cp_eth * (T_in_eth - T_out_eth)
Calculate the Reynolds number on the tube (water) side and select the correlation for calculating the convective heat transfer coefficient:
Re = (m_dot_water * d_inner * ρ_water) / (A_cross_section * μ_water)
where Q is the heat load, m_dot_eth is the mass flow rate of Ethylene Glycol, Cp_eth is the specific heat capacity of Ethylene Glycol, T_in_eth is the inlet temperature of Ethylene Glycol, and T_out_eth is the outlet temperature of Ethylene Glycol.
Calculate the efficiency (e) of the heat exchanger: e = Q / (UA)
where UA is the overall heat transfer coefficient area product.
Calculate the Reynolds number on the tube (water) side and select the correlation for calculating the convective heat transfer coefficient:
Re = (m_dot_water * d_inner * ρ_water) / (A_cross_section * μ_water)
where m_dot_water is the mass flow rate of water, d_inner is the inner diameter of the tube, ρ_water is the density of water, A_cross_section is the cross-sectional area of the tube, and μ_water is the dynamic viscosity of water. Select an appropriate correlation based on the Reynolds number range.
Calculate the required length of the heat exchanger in new condition (without fouling):
L = Q / (h0 * A_outer)
where L is the length of the heat exchanger, h0 is the outer convective heat transfer coefficient, and A_outer is the outer surface area of the tubes.
Calculate the required length of the heat exchanger considering fouling:
L_fouling = L / (1 + fouling_coefficient)
where L_fouling is the required length of the heat exchanger considering fouling, and fouling_coefficient is the fouling coefficient.
Note: The specific values for density, specific heat capacity, and dynamic viscosity of the fluids will be required to perform the calculations.
Learn more about length here
https://brainly.com/question/14288250
#SPJ11
A1 m-diameter corrugated metal storm water pipe (n = 0.024) is flowing full with a discharge of 4 m/sec. Determine the friction head loss over a 100 m length Answer
The friction head loss over a 100 m length of A1 m-diameter corrugated metal storm water pipe (n = 0.024) flowing full with a discharge of 4 m/sec can be determined using the Darcy-Weisbach equation which is expressed as follows:
hf = f x (L/D) x (V^2/2g).
Where:
hf = friction head loss
f = friction factor
L = pipe length
D = pipe diameter
V = fluid velocity
g = acceleration due to gravity.
Assuming that the stormwater pipe is horizontal and that the flow is turbulent (i.e. Reynolds number is greater than 4000), the friction factor (f) can be obtained from the Moody chart by finding the intersection of the Reynolds number and the relative roughness of the pipe.
For a corrugated metal pipe, the relative roughness is typically in the range of 0.01 to 0.015. Using a value of 0.013, the Reynolds number can be calculated as follows:
Re = (VD)/ν Where:
ν = kinematic viscosity of water For water at 20°C, the kinematic viscosity is 1.004 x 10^-6 m2/sRe
= (4 x A1)/(0.013 x 1) x (1.004 x 10^-6)Re
= 3068.17.
To know more about friction visit:
https://brainly.com/question/28356847
#SPJ11
need this answered
4. Convert the following hexadecimal numbers into their denary equivalents: (a) \( \mathrm{C}_{16} \) (b) \( \mathrm{BD}_{16} \) Solution:
(a) The hexadecimal number C₁₆ is equal to 12 in decimal.
(b) The hexadecimal number BD₁₆ is equal to 189 in decimal.
(a) To convert a single-digit hexadecimal number to decimal, we simply take its corresponding decimal value. In this case, C₁₆ corresponds to 12 in decimal.
The hexadecimal number C₁₆ can be converted to its decimal equivalent as follows:
C₁₆ = 12 × 6⁰ = 12
Therefore, C₁₆ is equal to 12 in decimal.
(b) : To convert a multi-digit hexadecimal number to decimal, we multiply each digit by the corresponding power of 16 and sum the results. In this case, BD₁₆ corresponds to
BD₁₆ = 11 × 16¹ + 13 × 16⁰ = 189
which simplifies to 189 in decimal.
To know more about hexadecimal number visit:
https://brainly.com/question/13262331
#SPJ11
Question 6 (1 point) Listen If the rest of the sketch is correct, what will we see in the serial monitor when the following portion is executed (assuming there is no outer loop)? int x = 5; int y = 2; do { y = y + x; Serial.print(y); Serial.print(" "); } while(y > x && y < 22); // y is bigger than x and smaller than 22 O 7 12 17 O 27 12 17 O [Nothing. The program never enters this loop.] O 712 17 22
If the rest of the sketch is correct the thing that one see in the serial monitor when the following portion is executed is O 7 12 17
What is the loopA "do while" loop is a feature in computer programming that lets a section of code run over and over again until a certain condition is met. The do while method has a step and a rule.
Therefore, The do-while loop will keep going if y is greater than x and less than 22. At first, x equals 5 and y equals 2. The loop will run at least one time because the condition is true. In the loop, y gets bigger by adding x to it (y = y + x). This means that y becomes 7 the first time it's done.
Read more about serial monitor here:
https://brainly.com/question/33179222
#SPJ4
The outside dimensions of a component with no axial or cylindrical symmetry (e.g., an engine block) need to be manufactured to tight tolerances. Select an appropriate machining process. a Turning b Milling c Drilling d Planing
When it comes to machining a component with no axial or cylindrical symmetry, milling is an appropriate machining process to achieve tight tolerances.
Milling is a process where the cutting tool is rotated to remove material from the workpiece to achieve the desired shape and size. The cutting tool is fed in different directions to create slots, contours, and other complex features.
There are two types of milling operations, namely conventional milling and climb milling. Conventional milling is where the cutting tool rotates in the opposite direction as the direction of feed, and climb milling is where the cutting tool rotates in the same direction as the direction of feed.
To know more about tool visit:
https://brainly.com/question/31719557
#SPJ11
Fixture Inside Diameter = 49.29mm Air Inlet Area of Dryer = 61.65mm Elevation Difference Inlet/Outlet = 12.36mm Air exit temperature 35.15 °C Exit velocity = 4.9m/s Input Voltage = 240V Input Current=1.36A Average Temp. of Nozzle=25.5 °C Outside Diameter of Nozzle = 58.12mm Room Temperature = 23.5 °C Barometric Pressure = 101.325 Pa Length of Heated Surface = 208.70mm Density of exit air= 0.519 l/m^3 Mass flow rate=m= 0.157kg/s Change of enthalpy=317.14J This is A Simple Hairdryer Experiment to Demonstrate the First Law of Thermodynamics and the data provided are as seen above. Calculate the following A) Change of potential energy B) Change of kinetic energy C) Heat loss D) Electrical power output E) Total thermal power in F) Total thermal power out G) %error
The final answers for these values are: a) 0.00011 J, b) 0.596J, c) 1.828J, d) 326.56W, e) 150.72W, f) 148.89W, and g) 1.22%.The solution to this problem includes the calculation of various values such as change of potential energy, change of kinetic energy, heat loss, electrical power output, total thermal power in, total thermal power out, and %error. Below is the stepwise explanation for each value.
A) Change of potential energy= mgh= 0.157kg/s × 9.81m/s² × 0.01236m = 0.00011 J.
B) Change of kinetic energy= 1/2 × ρ × A × V₁² × (V₂² - V₁²) = 0.5 × 0.519 kg/m³ × 0.006406 m² × 0.076 × (4.9² - 0.076²) = 0.596 J.
C) Heat loss= m × cp × (t₁ - t₂) = 0.157 kg/s × 1.006 kJ/kg·K × (35.15 - 23.5) = 1.828 J.
D) Electrical power output= V × I = 240V × 1.36A = 326.56W.
E) Total thermal power in= m × cp × (t₂ - t_room) = 0.157 kg/s × 1.006 kJ/kg·K × (35.15 - 23.5) = 1.828 J.
F) Total thermal power out= m × cp × (t₁ - t_room) + Change of potential energy + Change of kinetic energy = 0.157 kg/s × 1.006 kJ/kg·K × (25.5 - 23.5) + 0.00011J + 0.596J = 148.89 W.
G) %error= ((Thermal power in - Thermal power out) / Thermal power in) × 100% = ((150.72W - 148.89W) / 150.72W) × 100% = 1.22%.
To learn more about kinetic energy
https://brainly.com/question/999862
#SPJ11
Tool life data received from a turning operation shows a tool life of 15 min at a velocity of 150 m/min, and tool life of 35 min at a velocity of 80 m/min.
Using this data, determine:
I. The n and C values in the Taylor tool life equation.
Using these n and C values from I, determine:
II. Tool life for a speed of 90 m/min, and
III. Cutting speed corresponding to a tool life of 25 min,
I. The Taylor tool life equation is represented by the following relation:
VTⁿ = C
Where V is the cutting speed, T is the tool life, n and C are constants.The tool life data received from a turning operation is:Tool life, T1 = 15 min at a velocity, V1 = 150 m/minTool life, T2 = 35 min at a velocity, V2 = 80 m/minThe Taylor tool life equation can be rearranged as: n = log (T2/T1) / log (V1/V2)
Substituting the values of T1, T2, V1, and V2 in the above equation we get:
n = log (35/15) / log (150/80)n
= 0.141II.
The tool life equation can also be represented as
: T = C/ V^n
To find the tool life for a speed of 90 m/min: Substituting n and C values in the above equation, we get:
T = C/ V^nT
= 15.09 minIII.
To find the cutting speed corresponding to a tool life of 25 min:
Substituting the n and C values in the Taylor tool life equation we get:
V = C/Tⁿ
Substituting the value of T = 25 min, n = 0.141, and C = 840 in the above equation we get:
V = 107.4 m/min
Therefore, the tool life for a speed of 90 m/min is 15.09 min and the cutting speed corresponding to a tool life of 25 min is 107.4 m/min.
To know more about Taylor tool life equation visit:
https://brainly.com/question/33289606
#SPJ11
Consider the steady, two-dimensional, incompressible velocity field given by ⃗ = (u, v) = (1.3 + 2.8x) + (1.5 - 2.8y) . Velocity measured in m/s. Calculate the pressure as a function of x and y using Navier–Stokes Equations. Clearly state the assumptions and boundary conditions.
The Navier-Stokes equations are used to describe the movement of a fluid and are used extensively in fluid dynamics. The equations are a set of partial differential equations that describe how a fluid moves, what forces are acting on it, and how these forces affect the motion of the fluid.
The equations are named after Claude-Louis Navier and George Gabriel Stokes who were among the first to derive them. The equations are used to solve for the velocity, pressure, and density of a fluid as a function of space and time.In this problem, we are given a steady, two-dimensional, incompressible velocity field given by ⃗ = (u, v)
= (1.3 + 2.8x) + (1.5 - 2.8y). We are asked to calculate the pressure as a function of x and y using the Navier-Stokes equations.
The flow is two-dimensional, which means that there is no flow in the z-direction.The flow is steady, which means that the velocity and pressure do not change with time.Boundary Conditions:At the boundary of the fluid, the velocity is zero. This is known as the no-slip condition.At the top and bottom of the fluid, the velocity is zero. This is known as the free-slip condition.At the inlet and outlet of the fluid, the velocity is known.
This is known as the Dirichlet condition.We can now write down the Navier-Stokes equations:ρ(Dv/Dt) = - ∇p + µ∇²vwhere ρ is the density of the fluid, v is the velocity vector, p is the pressure, µ is the dynamic viscosity of the fluid, and D/Dt is the material derivative.
This means that the density of the fluid is constant and does not change with timeThis is known as the no-slip condition.At the top and bottom of the fluid, the velocity is zero. This is known as the free-slip condition.At the inlet and outlet of the fluid, the velocity is known. This is known as the Dirichlet condition.
To know more about equations visit:
https://brainly.com/question/29538993
#SPJ11
A supermarket of dimensions 20m x 15m and 4m high has a white ceiling and mainly dark walls. The working plane is lm above floor level. Bare fluorescent tube light fittings with two 58 W, 1500mm lamps are to be used, of 5100 lighting design lumens, to provide 400 lx. Their normal spacing-to-height ratio is 1.75 and total power consumption is 140 W. Calculate the number of luminaires needed, the electrical loading per square metre of floor area and the circuit current. Generate and draw the layout of the luminaires. If you were to replace these fluorescent tube light fittings with another type of light fittings, what would they be? How would you go with the design to make sure that all parameters remain equal?
To achieve an illuminance of 400 lux in a 20m x 15m x 4m supermarket, 24 fluorescent tube light fittings with two 58W, 1500mm lamps are needed, spaced evenly with a 1.75 spacing-to-height ratio. The electrical loading is 0.47 W/m² and the circuit current is 0.64 A.
To calculate the number of luminaires needed, we first need to determine the total surface area of the supermarket's floor:
Surface area = length x width = 20m x 15m = 300m²
Next, we need to determine the total amount of light needed to achieve the desired illuminance of 400 lux:
Total light = illuminance x surface area = 400 lux x 300m² = 120,000 lumens
Each fluorescent tube light fitting has a lighting design lumen output of 5100 lumens, and we need a total of 120,000 lumens. Therefore, the number of luminaires needed is:
Number of luminaires = total light / lumen output per fitting
Number of luminaires = 120,000 lumens / 5100 lumens per fitting
Number of luminaires = 23.53
We need 24 luminaires to achieve the desired illuminance in the supermarket. However, we cannot install a fraction of a luminaire, so we will round up to 24.
The electrical loading per square metre of floor area is:
Electrical loading = total power consumption / surface area
Electrical loading = 140 W / 300m²
Electrical loading = 0.47 W/m²
The circuit current can be calculated using the following formula:
Circuit current = total power consumption / voltage
Assuming a voltage of 220V:
Circuit current = 140 W / 220V
Circuit current = 0.64 A
To generate a layout of the luminaires, we can use a grid system with a spacing-to-height ratio of 1.75. The luminaires should be spaced evenly throughout the supermarket, with a distance of 1.75 times the mounting height between each luminaire. Assuming a mounting height of 1m, the luminaires should be spaced 1.75m apart.
To know more about electrical loading, visit:
brainly.com/question/30437919
#SPJ11
H.W 1 A binary-vapour cycle operates on mercury and steam. Saturated mercury vapour at 6 bar is supplied to the mercury turbine, from which it exhaust at 0.08 bar. The mercury condenser generates saturated steam at 20 bar which is expanded in a steam turbine to 0.04 bar. (i) Find the overall efficiency of the cycle. (ii) If 50000 kg/h of steam flows through the steam turbine, what is the flow through the mercury turbine ? (iii) Assuming that all processes are reversible, what is the useful work done in the binary vapour cycle for the specified steam flow? (iv) If the steam leaving the mercury condenser is superheated to a temperature of 300°C in a superheater located in the mercury boiler, and if the internal efficiencies of the mercury and steam turbines are 0.85 and 0.87 respectively, calculate the overall efficiency of the cycle.
Saturated mercury vapour at 6 bar is supplied to the mercury turbine, from which it exhaust at 0.08 bar. The mercury condenser generates saturated steam at 20 bar which is expanded in a steam turbine to 0.04 bar.
Internal efficiencies of the mercury and steam turbines are 0.85 and 0.87 respectively. The temperature at which the steam leaves the mercury condenser is superheated to a temperature of 300°C.Flow of steam turbine, m1 = 50000 kg/h Part. The overall efficiency of the binary-vapor cycle is given as:
Efficiency of cycle = (useful work output / total heat supplied) x 100%Let the mass flow rate of mercury in the cycle be m2.The mass flow rate of steam in the cycle will be (m1 - m2).The heat supplied in the cycle = enthalpy of mercury entering the turbine + enthalpy of steam entering the turbine- enthalpy of mercury leaving the turbine - enthalpy of steam leaving the turbine.
To know more about Saturated visit:
https://brainly.com/question/30550270
#SPJ11