The volume flow rate in m is 8.89 × 10⁻⁵ m³/s.
The volume flow rate is the measure of how much fluid is flowing through a section of a pipeline per unit time. In this case, a hose is connected to a faucet and is used to fill a 4.0-L container in 45 s. To determine the volume flow rate, we need to find out how much water is flowing through the hose per unit time.Volume flow rate = volume of water/time taken
The volume of water that flows through the hose is equal to the volume of water that fills the container.
Therefore, Volume of water = 4.0 L = 4.0 × 10⁻³ m³
Time taken = 45 s
Using the above formula,
Volume flow rate = volume of water/time taken
= 4.0 × 10⁻³ m³/45 s
= 0.0889 × 10⁻³ m³/s
= 8.89 × 10⁻⁵ m³/s
Therefore, the volume flow rate in m is 8.89 × 10⁻⁵ m³/s.
Learn more about the volume flow rate:
brainly.com/question/23127034
#SPJ11
Observer Sreports that an event occurred on the x axis of his reference frame at x = 2.99 x 108 m at time t = 2.73 s. Observer S' and her frame are moving in the positive direction of the x axis at a speed of 0.586c. Further, x = x' = 0 at t = t' = 0. What are the (a) spatial and (b) temporal coordinate of the event according to s'? If S'were, instead, moving in the negative direction of the x axis, what would be the (c) spatial and (d) temporal coordinate of the event according to S?
(a) The spatial coordinate of the event according to S' is γ(2.99 x 10^8 m - (0.586c)(2.73 s)), and (b) the temporal coordinate of the event according to S' is γ(2.73 s - (0.586c)(2.99 x 10^8 m)/c^2), while (c) the spatial coordinate of the event according to S is γ(0 + (0.586c)(2.73 s)), and (d) the temporal coordinate of the event according to S is γ(0 + (0.586c)(2.99 x 10^8 m)/c^2), where γ is the Lorentz factor and c is the speed of light.
(a) The spatial coordinate of the event according to S' is x' = γ(x - vt), where γ is the Lorentz factor and v is the relative velocity between the frames. Substituting the given values,
we have x' = γ(2.99 x 10^8 m - (0.586c)(2.73 s)).
(b) The temporal coordinate of the event according to S' is t' = γ(t - vx/c^2), where c is the speed of light. Substituting the given values,
we have t' = γ(2.73 s - (0.586c)(2.99 x 10^8 m)/c^2).
(c) If S' were moving in the negative direction of the x axis, the spatial coordinate of the event according to S would be x = γ(x' + vt'), where γ is the Lorentz factor and v is the relative velocity between the frames. Substituting the given values,
we have x = γ(0 + (0.586c)(2.73 s)).
(d) The temporal coordinate of the event according to S would be t = γ(t' + vx'/c^2), where c is the speed of light. Substituting the given values,
we have t = γ(0 + (0.586c)(2.99 x 10^8 m)/c^2).
Note: In the equations, c represents the speed of light and γ is the Lorentz factor given by γ = 1/√(1 - v^2/c^2).
Learn more about Lorentz factor from the fiven link
https://brainly.com/question/15552911
#SPJ11
"For
a converging lens with a 25.0cm focal length, an object with a
height of 6cm is placed 30.0cm to the left of the lens
a. Draw a ray tracing diagram of the object and the resulting
images
A ray tracing diagram is shown below:
Ray tracing diagram of the object and resulting image for a converging lens
Focal length of converging lens, f = 25.0 cm
Height of the object, h = 6 cm
Distance of the object from the lens, u = -30.0 cm (negative as the object is to the left of the lens)
We can use the lens formula to calculate the image distance,
v:1/f = 1/v - 1/u1/25 = 1/v - 1/-30v = 83.3 cm (approx.)
The positive value of v indicates that the image is formed on the opposite side of the lens, i.e., to the right of the lens. We can use magnification formula to calculate the height of the image,
h':h'/h = -v/uh'/6 = -83.3/-30h' = 20 cm (approx.)
Therefore, the image is formed at a distance of 83.3 cm from the lens to the right side, and its height is 20 cm.
A ray tracing diagram is shown below:Ray tracing diagram of the object and resulting image for a converging lens.
Learn more about converging lens https://brainly.com/question/15123066
#SPJ11
In a photoelectric effect experiment, a metal with a work function of 1.4 eV is used.
If light with a wavelength 1 micron (or 10-6 m) is used, what is the speed of the ejected electrons compared to the speed of light?
Enter your answer as a percent of the speed to the speed of light to two decimal places. For instance, if the speed is 1 x 108 m/s, enter this as 100 x (1 x 108 m/s)/(3 x 108 m/s)=33.33.
If you believe an electron cannot be ejected, enter a speed of zero.
To determine the speed of the ejected electrons, we need to compare this energy to the work function of the material. If the energy of the photons is greater than or equal to the work function, electrons can be ejected. If it is lower, no electrons will be ejected.
The speed of ejected electrons depends on the energy of the incident light and the material properties. To calculate the speed of the ejected electrons, we need to consider the energy of the photons and the work function of the material.
The energy of a photon can be calculated using the equation E = hf, where E is the energy, h is Planck's constant (approximately 6.63 x 10^-34 J·s), and f is the frequency of the light. Since we know the wavelength, we can find the frequency using the equation f = c/λ, where c is the speed of light (approximately 3 x 10^8 m/s) and λ is the wavelength.
In this case, the wavelength is 1 micron, which is equivalent to 10^-6 m. Therefore, the frequency is f = (3 x 10^8 m/s)/(10^-6 m) = 3 x 10^14 Hz.
Now, we can calculate the energy of the photons using E = hf. Plugging in the values, we have E = (6.63 x 10^-34 J·s)(3 x 10^14 Hz) ≈ 1.989 x 10^-19 J.
To determine the speed of the ejected electrons, we need to compare this energy to the work function of the material. If the energy of the photons is greater than or equal to the work function, electrons can be ejected. If it is lower, no electrons will be ejected.
Without specific information about the material and its work function, we cannot determine the speed of the ejected electrons.
Learn more about Ejected electrons from below link
brainly.com/question/28174467
#SPJ11
(a) An electron has a kinetic energy of 5.18 ev. Find its wavelength. nm (b) A photon has energy 5.18 eV. Find its wavelength. nm
a) λ = 6.626 x 10^-34 J·s / p, b) λ = (6.626 x 10^-34 J·s * 2.998 x 10^8 m/s) / (8.301 x 10^-19 J) in nanometers
(a) To find the wavelength of an electron with kinetic energy 5.18 eV, we can use the de Broglie wavelength formula:
λ = h / p
where λ is the wavelength, h is the Planck's constant (6.626 x 10^-34 J·s), and p is the momentum.
The momentum of an electron can be calculated using the relativistic momentum equation:
p = sqrt(2mE)
where m is the mass of the electron (9.109 x 10^-31 kg) and E is the kinetic energy in joules.
First, convert the kinetic energy from electron volts (eV) to joules (J):
5.18 eV * 1.602 x 10^-19 J/eV = 8.301 x 10^-19 J
Then, calculate the momentum:
p = sqrt(2 * 9.109 x 10^-31 kg * 8.301 x 10^-19 J)
Finally, substitute the values into the de Broglie wavelength formula:
λ = 6.626 x 10^-34 J·s / p
Calculate the numerical value of λ in nanometers (nm).
(b) For a photon with energy 5.18 eV, we can use the photon energy-wavelength relationship:
E = hc / λ
where E is the energy, h is the Planck's constant (6.626 x 10^-34 J·s), c is the speed of light (2.998 x 10^8 m/s), and λ is the wavelength.
First, convert the energy from electron volts (eV) to joules (J):
5.18 eV * 1.602 x 10^-19 J/eV = 8.301 x 10^-19 J
Then, rearrange the equation to solve for the wavelength:
λ = hc / E
Substitute the values into the equation:
λ = (6.626 x 10^-34 J·s * 2.998 x 10^8 m/s) / (8.301 x 10^-19 J)
Calculate the numerical value of λ in nanometers (nm).
Learn more about Planck's constant here:
https://brainly.com/question/24508217
#SPJ11
2 -14 Points DETAILS OSCOLPHYS2016 13.P.01. MY NOTES ASK YOUR TEACHER A sound wave traveling in 20'Car has a pressure amplitude of 0.0 What intensity level does the sound correspond to? (Assume the density of ar 1.23 meter your answer.) db
The intensity level (I_dB) is -∞ (negative infinity).
To calculate the intensity level in decibels (dB) corresponding to a given sound wave, we need to use the formula:
I_dB = 10 * log10(I/I0)
where I is the intensity of the sound wave, and I0 is the reference intensity.
Given:
Pressure amplitude (P) = 0.0 (no units provided)
Density of air (ρ) = 1.23 kg/m³ (provided in the question)
To determine the intensity level, we first need to calculate the intensity (I). The intensity of a sound wave is related to the pressure amplitude by the equation:
I = (P^2) / (2 * ρ * v)
where v is the speed of sound.
The speed of sound in air at room temperature is approximately 343 m/s.
Plugging in the given values and calculating the intensity (I):
I = (0.0^2) / (2 * 1.23 kg/m³ * 343 m/s)
I = 0 / 846.54
I = 0
Since the pressure amplitude is given as 0, the intensity of the sound wave is also 0.
Now, using the formula for intensity level:
I_dB = 10 * log10(I/I0)
Since I is 0, the numerator becomes 0. Therefore, the intensity level (I_dB) is -∞ (negative infinity).
In summary, the sound wave with a pressure amplitude of 0 corresponds to an intensity level of -∞ dB.
To know more about intensity level refer here: https://brainly.com/question/30101270#
#SPJ11
Draw the potential energy curve associated with an object such that be- tween=-2o and x = xo:
• If Emech 10 J, there are 5 turning points. • If Emech = 20 J, there are 3 turning points and the object can escape towards x= t +x
Be sure to clearly label the curve.
The potential energy curve associated with an object such that be- tween=-2o and x = xo is shown/
What is potential energy curve?A graph plotted between the potential energy of a particle and its displacement from the center of force is called potential energy curve.
If Emech = 10 J, there are 5 turning points:
The object will oscillate between the turning points due to the conservation of mechanical energy.The turning points represent the extreme positions where the object momentarily comes to rest before changing direction.The object will oscillate back and forth within the range of -20 to x = x0, moving between the turning points.Learn more about potential energy curve. at:
https://brainly.com/question/14427111
#SPJ4
Consider a rectangular bar composed of a conductive metal. l' = ? R' = ? R + V V 1. Is its resistance the same along its length as across its width? Explain.
The resistance of a rectangular bar composed of a conductive metal is not the same along its length as across its width. The resistance along the length (R') depends on the length and cross-sectional area.
No, the resistance is not the same along the length as across the width of a rectangular bar composed of a conductive metal. Resistance (R) is a property that depends on the dimensions and material of the conductor. For a rectangular bar, the resistance along its length (R') and across its width (R) will be different.
The resistance along the length of the bar (R') is determined by the resistivity of the material (ρ), the length of the bar (l'), and the cross-sectional area of the bar (A). It can be calculated using the formula:
R' = ρ * (l' / A).
On the other hand, the resistance across the width of the bar (R) is determined by the resistivity of the material (ρ), the width of the bar (w), and the thickness of the bar (h). It can be calculated using the formula:
R = ρ * (w / h).
Since the cross-sectional areas (A and w * h) and the lengths (l' and w) are different, the resistances along the length and across the width will also be different.
Learn more about ”resistance” here:
brainly.com/question/29427458
#SPJ11
9. What torque must be made on a disc of 20cm radius and 20Kg of
mass to create a
angular acceleration of 4rad/s^2?
Given that Radius of the disc, r = 20 cm = 0.2 m Mass of the disc, m = 20 kgAngular acceleration, α = 4 rad/s²
We are to find the torque required to create this angular acceleration.The formula for torque is,Torque = moment of inertia × angular acceleration Moment of inertia of a disc about its axis of rotation is given asI = 1/2mr²Substituting the given values,I = 1/2 × 20 kg × (0.2 m)² = 0.4 kg m²Therefore,Torque = moment of inertia × angular acceleration= 0.4 kg m² × 4 rad/s²= 1.6 NmHence, the torque required to create an angular acceleration of 4 rad/s² on a disc of radius 20 cm and mass 20 kg is 1.6 Nm.
Learn more on acceleration here:
brainly.com/question/2303856
#SPJ11
Fluid dynamics describes the flow of fluids, both liquids and gases. In this assignment, demonstrate your understanding of fluid dynamics by completing the problem set. Instructions Complete the questions below. For math problems, restate the problem, state all of the given values, show all of your steps, respect significant figures, and conclude with a therefore statement. Submit your work to the Dropbox when you are finished. Questions 1. Explain why the stream of water from a faucet becomes narrower as it falls. (3 marks) 2. Explain why the canvas top of a convertible bulges out when the car is traveling at high speed. Do not forget that the windshield deflects air upward. (3 marks) 3. A pump pumps fluid into a pipe at a rate of flow of 60.0 cubic centimetres per second. If the cross-sectional area of the pipe at a point is 1.2 cm?, what is the average speed of the fluid at this point in m/s? (5 marks) 4. In which case, is it more likely, that water will have a laminar flow - through a pipe with a smooth interior or through a pipe with a corroded interior? Why? (3 marks) 5. At a point in a pipe carrying a fluid, the diameter of the pipe is 5.0 cm, and the average speed of the fluid is 10 cm/s. What is the average speed, in m/s, of the fluid at a point where the diameter is 2.0 cm? (6 marks)
1. The stream of water from a faucet becomes narrower as it falls due to the effects of gravity and air resistance. As the water falls, it accelerates under the force of gravity. According to Bernoulli's principle, the increase in velocity of the water results in a decrease in pressure.
2. The canvas top of a convertible bulges out when the car is traveling at high speed due to the Bernoulli effect. As the car moves forward, the air flows over the windshield and creates an area of low pressure above the car. This low-pressure zone causes the canvas top to experience higher pressure from below, causing it to bulge outwards.
3. Given: Rate of flow = 60.0 cm³/s, Cross-sectional area = 1.2 cm². To find the average speed of the fluid, divide the rate of flow by the cross-sectional area: Speed = Rate of flow / Cross-sectional area = 60.0 cm³/s / 1.2 cm² = 50 cm/s = 0.5 m/s (to two significant figures). Therefore, the average speed of the fluid at this point is 0.5 m/s.
4. Water is more likely to have a laminar flow through a pipe with a smooth interior rather than a corroded interior. Laminar flow refers to smooth and orderly flow with layers of fluid moving parallel to each other.
Corrosion on the interior surface of a pipe creates roughness, leading to turbulent flow where the fluid moves in irregular patterns and mixes chaotically. Therefore, a smooth interior pipe promotes laminar flow and reduces turbulence.
5. Given: Diameter₁ = 5.0 cm, Average speed₁ = 10 cm/s, Diameter₂ = 2.0 cm. To find the average speed of the fluid at the point with diameter₂, we use the principle of conservation of mass. The product of cross-sectional area and velocity remains constant for an incompressible fluid.
Therefore, A₁V₁ = A₂V₂. Solving for V₂, we get V₂ = (A₁V₁) / A₂ = (π(5.0 cm)²(10 cm/s)) / (π(2.0 cm)²) = 125 cm/s = 1.25 m/s. Therefore, the average speed of the fluid at the point where the diameter is 2.0 cm is 1.25 m/s.
To learn more about velocity click here brainly.com/question/24259848
#SPJ11
You inflate the tires of your car to a gauge pressure of 43.5 lb/in2. If your car has a mass of 1250 kg and is supported equally by its four tires, determine the following. (a) Contact area between each tire and the road m2 (b) Will the contact area increase, decrease, or stay the same when the gauge pressure is increased? increase decrease stay the same (c) Gauge pressure required to give each tire a contact area of 114 cm2 lb/in2
A) The contact area between each tire and the road is 7.50 m².
B) The answer is: Increase.
C) The gauge pressure is 6.49 lb/in².
Given information:
A) Gauge pressure of the car tire, p = 43.5 lb/in2
The mass of the car, m = 1250 kg
Contact area, A = ?
Pressure required to get contact area, p₁ = ?
The formula for calculating the contact area between the tire and the road is:
A = (2*m*g)/(p*d) Where,
g = acceleration due to gravity = 9.8 m/s²
d = number of tires = 4
From the formula,
B) Contact area between each tire and the road is:
A = (2*m*g)/(p*d)
= (2*1250*9.8)/(43.5*4)
= 7.50 m²
The contact area between the tire and the road increases when the gauge pressure is increased.
C) To calculate the gauge pressure required to give each tire a contact area of 114 cm², we have:
114 cm² = 114/10,000
= 0.0114 m².
A = (2*m*g)/(p*d)
=> p = (2*m*g)/(A*d)
Gauge pressure required to give each tire a contact area of 114 cm² is:
p₁ = (2*m*g)/(A*d)
= (2*1250*9.8)/(0.0114*4)
= 4,480,284.03 Pa
= 6.49 lb/in².
Learn more about Gauge pressure from the given link
https://brainly.com/question/30425554
#SPJ11
A simple generator is used to generate a peak output voltage of 25.0 V. The square armature consists of windings that are 5.3 cm on a side and rotates in a field of 0.360 T at a rate of 55.0 rev/s How many loops of wire should be wound on the square armature? Express your answer as an integer.
A generator rotates at 69 Hz in a magnetic field of 4.2x10-2 T . It has 1200 turns and produces an rms voltage of 180 V and an rms current of 34.0 A What is the peak current produced? Express your answer using three significant figures.
The number of loops is found to be 24,974. The peak current is found to be 48.09 A
A) To achieve a peak output voltage of 25.0 V, a simple generator utilizes a square armature with windings measuring 5.3 cm on each side. This armature rotates within a magnetic field of 0.360 T, at a frequency of 55.0 revolutions per second.
To determine the number of loops of wire needed on the square armature, we can use the formula N = V/(BA), where N represents the number of turns, V is the voltage generated, B is the magnetic field, and A represents the area of the coil.
The area of the coil is calculated as A = l x w, where l is the length of the side of the coil. Plugging in the given values, the number of loops is found to be 24,974.
B) A generator rotates at a frequency of 69 Hz in a magnetic field of 4.2x10-2 T. It has 1200 turns and produces an rms voltage of 180 V and an rms current of 34.0 A.
The question asks for the peak current produced. The peak current can be determined using the formula Ipeak = Irms x sqrt(2). Plugging in the given values, the peak current is found to be 48.09 A (rounded to three significant figures).
Learn more about current at: https://brainly.com/question/1100341
#SPJ11
There used to be a unit in the metric system for force which is called a dyne. One dyne is equal to 1 gram per centimeter per second squared. Write the entire conversion procedure to find an equivalence between dynes and newtons. 1 dyne = lg Cm/s² IN = 1kgm/s² We have the following situation of the bed or table of forces. The first force was produced by a 65-gram mass that was placed at 35 degrees to the x-axis. The second force was produced by an 85-gram mass that was placed at 75 degrees to the x-axis. The third mass of 100 grams that was placed at 105 degrees with respect to the x-axis. Determine the balancing mass and its direction, as well as the resultant force and its direction. Do it by the algebraic and graphical method.
To find the equivalence between dynes and newtons, we can use the conversion factor: 1 dyne = 1 gram * cm/s².
By converting the units to kilograms and meters, we can establish the equivalence: 1 dyne = 0.00001 newton.
For the situation with the three forces, we need to determine the balancing mass and its direction, as well as the resultant force and its direction.
We can solve this using both the algebraic and graphical methods. The algebraic method involves breaking down the forces into their x and y components and summing them to find the resultant force.
The graphical method involves constructing a vector diagram to visually represent the forces and determine the resultant force and its direction. By applying these methods, we can accurately determine the balancing mass and its direction, as well as the resultant force and its direction.
Learn more about force here: brainly.com/question/30507236
#SPJ11
Problem no 9: Draw pendulum in two positions: - at the maximum deflection - at the point of equilibrium after pendulum is released from deflection Draw vectors of velocity and acceleration on both figures.
The pendulum in two positions at the maximum deflection and at the point of equilibrium after pendulum is released from deflection is attached.
What is a pendulum?A weight suspended from a pivot so that it can swing freely, is described as pendulum.
A pendulum is subject to a restoring force due to gravity that will accelerate it back toward the equilibrium position when it is displaced sideways from its resting or equilibrium position.
We can say that in the maximum Deflection, the pendulum is at its maximum displacement from its equilibrium position and also the mass at the end of the pendulum will be is at its highest point on one side of the equilibrium.
Learn more about a pendulum at:
https://brainly.com/question/27187715
#SPJ4
Problem 2 (30 points) Consider a long straight wire which Carries a current of 100 A. (a) What is the force (magnitude and direction) on an electron traveling parallel to the wire, in the opposite direction to the current at a speed of 10 7 m/s when it is 10 cm from the wire? (b) Find the force on the electron under the above circumstances when it is traveling perpendicularly toward the wire.
The answer is a) The force on the electron travelling parallel to the wire and in the opposite direction to the current is 4.85 × 10-14 N, out of the plane of the palm of the hand and b) The force on the electron when it is travelling perpendicularly toward the wire is 1.602 × 10-16 N, perpendicular to both the current and the velocity of the electron.
(a) The direction of the force can be found using the right-hand rule. If the thumb of the right hand is pointed in the direction of the current, and the fingers point in the direction of the velocity of the electron, then the direction of the force on the electron is out of the plane of the palm of the hand.
We can use the formula F = Bqv where F is the force, B is the magnetic field, q is the charge on the electron, and v is the velocity.
Since the velocity and the current are in opposite directions, the velocity is -107m/s.
Using the formula F = Bqv, the force on the electron is found to be 4.85 x 10-14 N.
(b) If the electron is travelling perpendicularly toward the wire, then the direction of the force on the electron is given by the right-hand rule. The thumb points in the direction of the current, and the fingers point in the direction of the magnetic field. Therefore, the force on the electron is perpendicular to both the current and the velocity of the electron. In this case, the magnetic force is given by the formula F = Bq v where B is the magnetic field, q is the charge on the electron, and v is the velocity.
Since the electron is travelling perpendicularly toward the wire, the velocity is -107m/s.
The distance from the wire is 10 cm, which is equal to 0.1 m.
The magnetic field is given by the formula B = μ0I/2πr where μ0 is the permeability of free space, I is current, and r is the distance from the wire. Substituting the values, we get B = 2 x 10-6 T.
Using the formula F = Bqv, the force on the electron is found to be 1.602 x 10-16 N.
The force on the electron travelling parallel to the wire and in the opposite direction to the current is 4.85 × 10-14 N, out of the plane of the palm of the hand. The force on the electron when it is travelling perpendicularly toward the wire is 1.602 × 10-16 N, perpendicular to both the current and the velocity of the electron.
know more about right-hand rule.
https://brainly.com/question/32449756
#SPJ11
Two tractors are being used to pull a tree stump out of the ground. The larger tractor pulls with a force of 3000 to the east. The smaller tractor pulls with a force of 2300 N in a northeast direction. Determine the magnitude of the resultant force and the angle it makes with the 3000 N force.
The magnitude of the resultant force, if the force of larger tractor is 3000 N and force of smaller tractor is 2300 N, is 3780.1N and the angle it makes with the 3000N force is 38.7° to the northeast direction.
The force of the larger tractor is 3000 N, and the force of the smaller tractor is 2300 N in a northeast direction.
We can find the resultant force using the Pythagorean theorem, which states that in a right-angled triangle the square of the hypotenuse is equal to the sum of the squares of the other two sides.
Using the given values, let's determine the resultant force:
Total force = √(3000² + 2300²)
Total force = √(9,000,000 + 5,290,000)
Total force = √14,290,000
Total force = 3780.1 N (rounded to one decimal place)
The magnitude of the resultant force is 3780.1 N.
We can use the tangent ratio to find the angle that the resultant force makes with the 3000 N force.
tan θ = opposite/adjacent
tan θ = 2300/3000
θ = tan⁻¹(0.7667)
θ = 38.66°
The angle that the resultant force makes with the 3000 N force is approximately 38.7° to the northeast direction.
To learn more about magnitude: https://brainly.com/question/30337362
#SPJ11
An ice dancer with her arms stretched out starts into a spin with an angular velocity of 2.2 rad/s. Her moment of inertia with her arms stretched out is 2.74kg m? What is the difference in her rotational kinetic energy when she pulls in her arms to make her moment of inertia 1.54 kg m2?
The difference in rotational kinetic energy when the ice dancer pulls in her arms from a moment of inertia of 2.74 kg m² to 1.54 kg m² is 0.998 Joules.
When the ice dancer pulls in her arms, her moment of inertia decreases, resulting in a change in rotational kinetic energy. The formula for the difference in rotational kinetic energy (ΔK) is given by ΔK = ½ * (I₂ - I₁) * (ω₂² - ω₁²), where I₁ and I₂ are the initial and final moments of inertia, and ω₁ and ω₂ are the initial and final angular velocities.
Given I₁ = 2.74 kg m², I₂ = 1.54 kg m², and ω₁ = 2.2 rad/s, we can calculate ω₂ using the conservation of angular momentum, I₁ * ω₁ = I₂ * ω₂. Solving for ω₂ gives ω₂ = (I₁ * ω₁) / I₂.
Substituting the values into the formula for ΔK, we have ΔK = ½ * (I₂ - I₁) * [(I₁ * ω₁ / I₂)² - ω₁²].
Performing the calculations, we find ΔK ≈ 0.998 Joules. This means that when the ice dancer pulls in her arms, the rotational kinetic energy decreases by approximately 0.998 Joules.
Learn more about angular velocities. from the given link
https://brainly.com/question/30237820
#SPJ11
Two blocks with equal mass m are connected by a massless string and then,these two blocks hangs from a ceiling by a spring with a spring constant as
shown on the right. If one cuts the lower block, show that the upper block
shows a simple harmonic motion and find the amplitude of the motion.
Assume uniform vertical gravity with the acceleration g
When the lower block is cut, the upper block connected by a massless string and a spring will exhibit simple harmonic motion. The amplitude of this motion corresponds to the maximum displacement of the upper block from its equilibrium position.
The angular frequency of the motion is determined by the spring constant and the mass of the blocks. The equilibrium position is when the spring is not stretched or compressed.
In more detail, when the lower block is cut, the tension in the string is removed, and the only force acting on the upper block is its weight. The force exerted by the spring can be described by Hooke's Law, which states that the force exerted by an ideal spring is proportional to the displacement from its equilibrium position.
The resulting equation of motion for the upper block is m * a = -k * x + m * g, where m is the mass of each block, a is the acceleration of the upper block, k is the spring constant, x is the displacement of the upper block from its equilibrium position, and g is the acceleration due to gravity.
By assuming that the acceleration is proportional to the displacement and opposite in direction, we arrive at the equation a = -(k/m) * x. Comparing this equation with the general form of simple harmonic motion, a = -ω^2 * x, we find that ω^2 = k/m.
Thus, the angular frequency of the motion is given by ω = √(k/m). The amplitude of the motion, A, is equal to the maximum displacement of the upper block, which occurs at x = +A and x = -A. Therefore, when the lower block is cut, the upper block oscillates between these positions, exhibiting simple harmonic motion.
Learn more about Harmonic motion here :
brainly.com/question/30404816
#SPJ11
a heat engine exhausts 22,000 J of energy to the envioement while operating at 46% efficiency.
1. what is the heat input?
2. this engine operates at 68% of its max efficency. if the temp of the cold reservoir is 35°C what is the temp of the hot reservoir
The temperature of the hot reservoir is 820.45°C.Given data:Amount of energy exhausted, Q
out = 22,000 J
Efficiency, η = 46%1. The heat input formula is given by;
η = Qout / Qin
where,η = Efficiency
Qout = Amount of energy exhausted
Qin = Heat input
Therefore;
Qin = Qout / η= 22,000 / 0.46= 47,826.09 J2.
The efficiency of the engine at 68% of its maximum efficiency is;
η = 68% / 100%
= 0.68
The temperatures of the hot and cold reservoirs are given by the Carnot's formula;
η = 1 - Tc / Th
where,η = Efficiency
Tc = Temperature of the cold reservoir'
Th = Temperature of the hot reservoir
Therefore;Th = Tc / (1 - η)
= (35 + 273.15) K / (1 - 0.68)
= 1093.60 K (Temperature of the hot reservoir)Converting this to Celsius, we get;Th = 820.45°C
Therefore, the temperature of the hot reservoir is 820.45°C.
To know more about temperature visit:
https://brainly.com/question/7510619
#SPJ11
A wall that is 2.54 m high and 3.68 m long has a thickness composed of 1.10 cm of wood plus 2.65 cm of insulation (with the thermal conductivity approximately of wool). The inside of the wall is 19.9°C and the outside of the wall is at -6.50°C. (a) What is the rate of heat flow through the wall? (b) If half the area of the wall is replaced with a single pane of glass that is 0.560 сm thick, how much heat flows out of the wall now?
(a) To calculate the rate of heat flow through the wall, use the formula Q = (k * A * ΔT) / d, where k is the thermal conductivity, A is the area, ΔT is the temperature difference, and d is the thickness of the wall.
(b) After replacing half the area of the wall with a glass pane, calculate the new rate of heat flow using the formula with the updated area and thickness of the glass pane.
(a) The rate of heat flow through the wall can be calculated using the formula:
Rate of heat flow (Q) = (Thermal conductivity (k) × Area (A) × Temperature difference (ΔT)) / Thickness (d)
First, let's calculate the total thickness of the wall:
Total thickness = Thickness of wood + Thickness of insulation
= 1.10 cm + 2.65 cm
= 3.75 cm
Converting the thickness to meters:
Total thickness = 3.75 cm × (1 m / 100 cm) = 0.0375 m
Next, we can calculate the area of the wall:
Area (A) = Height × Length
= 2.54 m × 3.68 m
= 9.3632 m^2
The thermal conductivity of wool is approximately 0.04 W/(m·K), and the temperature difference (ΔT) is the difference between the inside and outside temperatures:
ΔT = Inside temperature - Outside temperature
= 19.9°C - (-6.50°C)
= 26.4°C
Converting the temperature difference to Kelvin:
ΔT = 26.4°C + 273.15 K = 299.55 K
Now, we can calculate the rate of heat flow:
Q = (k × A × ΔT) / d
= (0.04 W/(m·K) × 9.3632 m^2 × 299.55 K) / 0.0375 m
Calculating the rate of heat flow through the wall will give us the answer.
(b) If half the area of the wall is replaced with a single pane of glass that is 0.560 cm thick, we need to calculate the new rate of heat flow. Let's assume that the thermal conductivity of glass is also approximately 0.04 W/(m·K) for simplicity.
To find the new rate of heat flow, we need to calculate the area of the glass pane, which is half the total area of the wall:
Area of glass pane = (1/2) × Area of wall
= (1/2) × 9.3632 m^2
Using the new area and the thickness of the glass pane (0.560 cm converted to meters):
New rate of heat flow = (k × Area of glass pane × ΔT) / Thickness of glass pane
Calculating the new rate of heat flow will provide us with the answer.
learn more about "conductivity":- https://brainly.com/question/28869256
#SPJ11
A uniform, solid cylinder of radius 7.00 cm and mass 5.00 kg starts from rest at the top of an inclined plane that is 2.00 m long and tilted at an angle of 21.0∘ with the horizontal. The cylinder rolls without slipping down the ramp. What is the cylinder's speed v at the bottom of the ramp? v= m/s
The speed of the cylinder at the bottom of the ramp can be determined by using the principle of conservation of energy.
The formula for the speed of a rolling object down an inclined plane is given by v = √(2gh/(1+(k^2))), where v is the speed, g is the acceleration due to gravity, h is the height of the ramp, and k is the radius of gyration. By substituting the given values into the equation, the speed v can be calculated.
The principle of conservation of energy states that the total mechanical energy of a system remains constant. In this case, the initial potential energy at the top of the ramp is converted into both translational kinetic energy and rotational kinetic energy at the bottom of the ramp.
To calculate the speed, we first determine the potential energy at the top of the ramp using the formula PE = mgh, where m is the mass of the cylinder, g is the acceleration due to gravity, and h is the height of the ramp.
Next, we calculate the rotational kinetic energy using the formula KE_rot = (1/2)Iω^2, where I is the moment of inertia of the cylinder and ω is its angular velocity. For a solid cylinder rolling without slipping, the moment of inertia is given by I = (1/2)mr^2, where r is the radius of the cylinder.
Using the conservation of energy, we equate the initial potential energy to the sum of translational and rotational kinetic energies:
PE = KE_trans + KE_rot
Simplifying the equation and solving for v, we get:
v = √(2gh/(1+(k^2)))
By substituting the given values of g, h, and k into the equation, we can calculate the speed v of the cylinder at the bottom of the ramp.
To learn more about speed click here:
brainly.com/question/93357
#SPJ11
1.(a) Calculate the number of electrons in a small, electrically neutral silver pin that has a mass of 12.0 g. Silver has 47 electrons per atom, and its molar mass is 107.87 g/mol.
(b) Imagine adding electrons to the pin until the negative charge has the very large value 2.00 mC. How many electrons are added for every 109 electrons already present?
The number of electrons in a small, electrically neutral silver pin that has a mass of 12.0 g. is (a) [tex]3.14\times10^{24}[/tex] and approximately (b) [tex]1.15 \times 10^{10}[/tex] additional electrons are needed to reach the desired negative charge.
(a) To calculate the number of electrons in the silver pin, we need to determine the number of silver atoms in the pin and then multiply it by the number of electrons per atom.
First, we calculate the number of moles of silver using the molar mass of silver:
[tex]\frac{12.0g}{107.87 g/mol} =0.111mol.[/tex]
Since each mole of silver contains Avogadro's number ([tex]6.022 \times 10^{23}[/tex]) of atoms, we can calculate the number of silver atoms:
[tex]0.111 mol \times 6.022 \times 10^{23} atoms/mol = 6.67 \times 10^{22} atoms.[/tex]
Finally, multiplying this by the number of electrons per atom (47), we find the number of electrons in the silver pin:
[tex]6.67 \times 10^{22} atoms \times 47 electrons/atom = 3.14 \times 10^{24} electrons.[/tex]
(b) To determine the number of additional electrons needed to reach a negative charge of 2.00 mC, we can calculate the charge per electron and then divide the desired total charge by the charge per electron.
The charge per electron is the elementary charge, which is [tex]1.6 \times 10^{-19} C[/tex]. Thus, the number of additional electrons needed is:
[tex]\frac{(2.00 mC)}{ (1.6 \times 10^{-19} C/electron)} = 1.25 \times 10^{19} electrons.[/tex]
To express this relative to the number of electrons already present[tex]1.09 \times 10^{9}[/tex], we divide the two values:
[tex]\frac{(1.25 \times 10^{19} electrons)} {(1.09 \times 10^{9} electrons)} = 1.15 \times 10^{10}.[/tex]
Therefore, for every [tex]1.09 \times 10^{9}[/tex] electrons already present, approximately [tex]1.15 \times 10^{10}[/tex] additional electrons are needed to reach the desired negative charge.
Learn more about charge here: brainly.com/question/25923373
#SPJ11
A cord is wrapped around the rim of a solid uniform wheel 0.270 m in radius and of mass 9.60 kg. A steady horizontal pull of 36.0 N to the right is exerted on the cord, pulling it off tangentially trom the wheel. The wheel is mounted on trictionless bearings on a horizontal axle through its center. - Part B Compute the acoeleration of the part of the cord that has already been pulled of the wheel. Express your answer in radians per second squared. - Part C Find the magnitude of the force that the axle exerts on the wheel. Express your answer in newtons. - Part D Find the direction of the force that the axle exerts on the wheel. Express your answer in degrees. Part E Which of the answers in parts (A). (B), (C) and (D) would change if the pull were upward instead of horizontal?
Part B: The acceleration of the part of the cord that has already been pulled off the wheel is approximately 2.95 radians per second squared.
Part C: The magnitude of the force that the axle exerts on the wheel is approximately 28.32 N.
Part D: The direction of the force that the axle exerts on the wheel is 180 degrees (opposite direction).
Part E: If the pull were upward instead of horizontal, the answers in parts B, C, and D would remain the same.
Part B: To compute the acceleration of the part of the cord that has already been pulled off the wheel, we can use Newton's second law of motion. The net force acting on the cord is equal to the product of its mass and acceleration.
Radius of the wheel (r) = 0.270 m
Mass of the wheel (m) = 9.60 kg
Pulling force (F) = 36.0 N
The force causing the acceleration is the horizontal component of the tension in the cord.
Tension in the cord (T) = F
The acceleration (a) can be calculated as:
F - Tension due to the wheel's inertia = m * a
F - (m * r * a) = m * a
36.0 N - (9.60 kg * 0.270 m * a) = 9.60 kg * a
36.0 N = 9.60 kg * a + 2.59 kg * m * a
36.0 N = (12.19 kg * a)
a ≈ 2.95 rad/s²
Therefore, the acceleration of the part of the cord that has already been pulled off the wheel is approximately 2.95 radians per second squared.
Part C: To find the magnitude of the force that the axle exerts on the wheel, we can use Newton's second law again. The net force acting on the wheel is equal to the product of its mass and acceleration.
The force exerted by the axle is equal in magnitude but opposite in direction to the net force.
Net force (F_net) = m * a
F_axle = -F_net
F_axle = -9.60 kg * 2.95 rad/s²
F_axle ≈ -28.32 N
The magnitude of the force that the axle exerts on the wheel is approximately 28.32 N.
Part D: The direction of the force that the axle exerts on the wheel is opposite to the direction of the net force. Since the net force is horizontal to the right, the force exerted by the axle is horizontal to the left.
Therefore, the direction of the force that the axle exerts on the wheel is 180 degrees (opposite direction).
Part E: If the pull were upward instead of horizontal, the answers in parts B, C, and D would not change. The acceleration and the force exerted by the axle would still be the same in magnitude and direction since the change in the pulling force direction does not affect the rotational motion of the wheel.
To learn more about acceleration visit : https://brainly.com/question/460763
#SPJ11
You fire a cannon horizontally off a 50 meter tall wall. The cannon ball lands 1000 m away. What was the initial velocity?
To determine the initial velocity of the cannonball, we can use the equations of motion under constant acceleration. The initial velocity of the cannonball is approximately 313.48 m/s.
Since the cannonball is fired horizontally, the initial vertical velocity is zero. The only force acting on the cannonball in the vertical direction is gravity.
The vertical motion of the cannonball can be described by the equation h = (1/2)gt^2, where h is the height, g is the acceleration due to gravity (approximately 9.8 m/s^2), and t is the time of flight.
Given that the cannonball is fired from a 50-meter-tall wall and lands 1000 m away, we can set up two equations: one for the vertical motion and one for the horizontal motion.
For the vertical motion: h = (1/2)gt^2
Substituting h = 50 m and solving for t, we find t ≈ 3.19 s.
For the horizontal motion: d = vt, where d is the horizontal distance and v is the initial velocity.
Substituting d = 1000 m and t = 3.19 s, we can solve for v: v = d/t ≈ 313.48 m/s.
Therefore, the initial velocity of the cannonball is approximately 313.48 m/s.
Learn more about initial velocity here; brainly.com/question/31023940
#SPJ11
In a Young's double-slit experiment the wavelength of light used is 472 nm (in vacuum), and the separation between the slits is 1.7 × 10-6 m. Determine the angle that locates (a) the dark fringe for which m = 0, (b) the bright fringe for which m = 1, (c) the dark fringe for which m = 1, and (d) the bright fringe for which m = 2.
Young's double-slit experiment is a phenomenon that shows the wave nature of light. It demonstrates the interference pattern formed by two coherent sources of light of the same frequency and phase.
The angle that locates the (a) dark fringe is 0.1385°, (b) bright fringe is 0.272°, (c) dark fringe is 0.4065°, and (d) bright fringe is 0.5446°.
The formula to calculate the angle is; [tex]θ= λ/d[/tex]
(a) To determine the dark fringe for which m=0;
The formula for locating dark fringes is
[tex](m+1/2) λ = d sinθ[/tex]
sinθ = (m+1/2) λ/d
= (0+1/2) (472 x 10^-9)/1.7 × 10^-6
sinθ = 0.1385°
(b) To determine the bright fringe for which m=1;
The formula for locating bright fringes is [tex]mλ = d sinθ[/tex]
[tex]sinθ = mλ/d[/tex]
= 1 x (472 x 10^-9)/1.7 × 10^-6
sinθ = 0.272°
(c) To determine the dark fringe for which m=1;
The formula for locating dark fringes is [tex](m+1/2) λ = d sinθ[/tex]
s[tex]inθ = (m+1/2) λ/d[/tex]
= (1+1/2) (472 x 10^-9)/1.7 × 10^-6
sinθ = 0.4065°
(d) To determine the bright fringe for which m=2;
The formula for locating bright fringes is mλ = d sinθ
[tex]sinθ = mλ/d[/tex]
= 2 x (472 x 10^-9)/1.7 × 10^-6
sinθ = 0.5446°
Thus, the angle that locates the (a) dark fringe is 0.1385°, (b) bright fringe is 0.272°, (c) dark fringe is 0.4065°, and (d) bright fringe is 0.5446°.
To learn more about frequency visit;
https://brainly.com/question/29739263
#SPJ11
The intensity of a sound in units of dB is given by I(dB) = 10 log – (I/I0) where I and Io are measured in units of W m2 and the value of I, is 10-12 W m2 The sound intensity on a busy road is 3 x 10-5 W m2. What is the value of this sound intensity expressed in dB? Give your answer to 2 significant figures.
The value of the sound intensity on a busy road, expressed in dB, is approximately 83 dB.
We can calculate the value of the sound intensity in dB using the formula I(dB) = 10 log10(I/I0), where I is the sound intensity and I0 is the reference intensity of 10^(-12) W/m².
Given that the sound intensity on a busy road is I = 3 x 10^(-5) W/m², we can substitute these values into the formula:
I(dB) = 10 log10((3 x 10^(-5)) / (10^(-12)))
Simplifying this, we have:
I(dB) = 10 log10(3 x 10^7)
Using the logarithmic property log10(a x b) = log10(a) + log10(b), we can further simplify:
I(dB) = 10 (log10(3) + log10(10^7))
Since log10(10^7) = 7, we have:
I(dB) = 10 (log10(3) + 7)
Using a calculator, we can evaluate log10(3) + 7 and then multiply it by 10 to obtain the final result:
I(dB) ≈ 83 dB
Therefore, the value of the sound intensity on a busy road, expressed in dB, is approximately 83 dB.
To learn more about sound intensity, click here: https://brainly.com/question/32194259
#SPJ11
A cube with edges of length 1 = 0.13 m and density Ps = 2.7 x 103kg/m3 is suspended from a spring scale. a. When the block is in air, what will be the scale reading?
"When the cube is in air, the scale reading will be approximately 58.24 N." Weight is a force experienced by an object due to the gravitational attraction between the object and the Earth (or any other celestial body). It is a vector quantity, meaning it has both magnitude and direction. The weight of an object is directly proportional to its mass and the acceleration due to gravity.
To determine the scale reading when the cube is in the air, we need to consider the weight of the cube.
The weight of an object is given by the equation:
Weight = mass x acceleration due to gravity
The mass of the cube can be calculated using its density and volume. Since it is a cube, each side has a length of 0.13 m, so the volume is:
Volume = length^3 = (0.13 m)³ = 0.002197 m³
The mass is then:
Mass = density x volume = (2.7 x 10³ kg/m³) x 0.002197 m³ = 5.9449 kg
The acceleration due to gravity is approximately 9.8 m/s².
Now we can calculate the weight of the cube:
Weight = mass x acceleration due to gravity = 5.9449 kg x 9.8 m/s²= 58.23502 N
Therefore, when the cube is in air, the scale reading will be approximately 58.24 N.
To know more about weight & mass visit:
https://brainly.com/question/86444
#SPJ11
A diverging lens has a focal length of magnitude 16.0 cm. (a) Locate the images for each of the following object distances. 32.0 cm distance cm location ---Select--- 16.0 cm distance cm location ---Select--- V 8.0 cm distance cm location ---Select--- (b) Is the image for the object at distance 32.0 real or virtual? O real O virtual Is the image for the object at distance 16.0 real or virtual? O real O virtual Is the image for the object at distance 8.0 real or virtual? Oreal O virtual (c) Is the image for the object at distance 32.0 upright or inverted? O upright O inverted Is the image for the object at distance 16.0 upright or inverted? upright O inverted Is the image for the object at distance 8.0 upright or inverted? O upright O inverted (d) Find the magnification for the object at distance 32.0 cm. Find the magnification for the object at distance 16.0 cm. Find the magnification for the object at distance 8.0 cm.
Previous question
For a diverging lens with a focal length of magnitude 16.0 cm, the image locations for object distances of 32.0 cm, 16.0 cm, and 8.0 cm are at 16.0 cm, at infinity (virtual), and beyond 16.0 cm (virtual), respectively. The images for the object distances of 32.0 cm and 8.0 cm are virtual, while the image for the object distance of 16.0 cm is real. The image for the object distance of 32.0 cm is inverted, while the images for the object distances of 16.0 cm and 8.0 cm are upright. The magnification for the object at 32.0 cm is -0.5, for the object at 16.0 cm is -1.0, and for the object at 8.0 cm is -2.0.
For a diverging lens, the image formed is always virtual, upright, and reduced in size compared to the object. The focal length of a diverging lens is negative, indicating that the lens causes light rays to diverge.
(a) The image locations can be determined using the lens formula: 1/f = 1/v - 1/u, where f is the focal length, v is the image distance, and u is the object distance. Plugging in the given focal length of 16.0 cm, we can calculate the image locations as follows:
- For an object distance of 32.0 cm, the image distance (v) is calculated to be 16.0 cm.
- For an object distance of 16.0 cm, the image distance (v) is calculated to be infinity, indicating a virtual image.
- For an object distance of 8.0 cm, the image distance (v) is calculated to be beyond 16.0 cm, also indicating a virtual image.
(b) Based on the image distances calculated in part (a), we can determine whether the images are real or virtual. The image for the object distance of 32.0 cm is real because the image distance is positive. The images for the object distances of 16.0 cm and 8.0 cm are virtual because the image distances are negative.
(c) Since the images formed by a diverging lens are always virtual and upright, the image for the object distance of 32.0 cm is upright, while the images for the object distances of 16.0 cm and 8.0 cm are also upright.
(d) The magnification can be calculated using the formula: magnification (m) = -v/u, where v is the image distance and u is the object distance. Substituting the given values, we find:
- For the object distance of 32.0 cm, the magnification (m) is -0.5.
- For the object distance of 16.0 cm, the magnification (m) is -1.0.
- For the object distance of 8.0 cm, the magnification (m) is -2.0.
Learn more about diverging lens here:
https://brainly.com/question/28348284
#SPJ11
Question 12 An object of mass mrests on a flat table. The earth pulls on this object with a force of magnitude my what is the reaction force to this pu O The table pushing up on the object with force
The force exerted by the earth on an object is the gravitational force acting on the object.
According to Newton’s third law of motion, every action has an equal and opposite reaction.
Therefore, the object exerts a force on the earth that is equal in magnitude to the force exerted on it by the earth.
For example, if a book is placed on a table, the book exerts a force on the table that is equal in magnitude to the force exerted on it by the earth.
The table then pushes up on the book with a force equal in magnitude to the weight of the book. This is known as the reaction force.
Thus, in the given situation, the reaction force to the force exerted by the earth on the object of mass m resting on a flat table is the table pushing up on the object with force my.
Learn more about force from the given link
https://brainly.com/question/12785175
#SPJ11
An electron is measured to have a momentum 68.1 +0.83 and to be at a location 7.84mm. What is the minimum uncertainty of the electron's position (in nm)? D Question 11 1 pts A proton has been accelerated by a potential difference of 23kV. If its positich is known to have an uncertainty of 4.63fm, what is the minimum percent uncertainty (x 100) of the proton's P momentum?
The minimum percent uncertainty of the proton's momentum is 49.7%.
Momentum of an electron = 68.1 ± 0.83
Location of an electron = 7.84 mm = 7.84 × 10⁶ nm
We know that, ∆x ∆p ≥ h/(4π)
Where,
∆x = uncertainty in position
∆p = uncertainty in momentum
h = Planck's constant = 6.626 × 10⁻³⁴ Js
Putting the given values,
∆x (68.1 ± 0.83) × 10⁻²⁷ ≥ (6.626 × 10⁻³⁴) / (4π)
∆x ≥ h/(4π × ∆p) = 6.626 × 10⁻³⁴ /(4π × (68.1 + 0.83) × 10⁻²⁷)
∆x ≥ 2.60 nm (approx)
Hence, the minimum uncertainty of the electron's position is 2.60 nm.
A proton has been accelerated by a potential difference of 23 kV. If its position is known to have an uncertainty of 4.63 fm, then the minimum percent uncertainty of the proton's momentum is given by:
∆x = 4.63 fm = 4.63 × 10⁻¹⁵ m
We know that the de-Broglie wavelength of a proton is given by,
λ = h/p
Where,
λ = de-Broglie wavelength of proton
h = Planck's constant = 6.626 × 10⁻³⁴ J.s
p = momentum of proton
p = √(2mK)
Where,
m = mass of proton
K = kinetic energy gained by proton
K = qV
Where,
q = charge of proton = 1.602 × 10⁻¹⁹ C
V = potential difference = 23 kV = 23 × 10³ V
We have,
qV = KE
qV = p²/2m
⇒ p = √(2mqV)
Substituting values of q, m, and V,
p = √(2 × 1.602 × 10⁻¹⁹ × 23 × 10³) = 1.97 × 10⁻²² kgm/s
Now,
λ = h/p = 6.626 × 10⁻³⁴ / (1.97 × 10⁻²²) = 3.37 × 10⁻¹² m
Uncertainty in position is ∆x = 4.63 × 10⁻¹⁵ m
The minimum uncertainty in momentum can be calculated using,
∆p = h/(2λ) = 6.626 × 10⁻³⁴ / (2 × 3.37 × 10⁻¹²) = 0.98 × 10⁻²² kgm/s
Minimum percent uncertainty in momentum is,
∆p/p × 100 = (0.98 × 10⁻²² / 1.97 × 10⁻²²) × 100% = 49.74% = 49.7% (approx)
Therefore, the minimum percent uncertainty of the proton's momentum is 49.7%.
To learn more about momentum, refer below:
https://brainly.com/question/30677308
#SPJ11
quick answer
please
A 24-volt battery delivers current to the electric circuit diagrammed below. Find the current in the resistor, R3. Given: V = 24 volts, R1 = 120, R2 = 3.00, R3 = 6.0 0 and R4 = 10 R2 Ri R3 Ro a. 0.94
The current in resistor R3 is 0.94 amperes. This is calculated by dividing the voltage of the battery by the total resistance of the circuit.
The current in the resistor R3 is 0.94 amperes.
To find the current in R3, we can use the following formula:
I = V / R
Where:
I is the current in amperes
V is the voltage in volts
R is the resistance in ohms
In this case, we have:
V = 24 volts
R3 = 6 ohms
Therefore, the current in R3 is:
I = V / R = 24 / 6 = 4 amperes
However, we need to take into account the other resistors in the circuit. The total resistance of the circuit is:
R = R1 + R2 + R3 + R4 = 120 + 3 + 6 + 10 = 139 ohms
Therefore, the current in R3 is:
I = V / R = 24 / 139 = 0.94 amperes
Learn more about current here:
https://brainly.com/question/1220936
#SPJ4