The amplitude drops to one-quarter of the initial value after 102.7 oscillations.
λ=1/51⋅0.20slog(1/2)=−0.68s^-1
Using the previous result we can evaluate the amplitude as a function of time to obtain the elapsed time until the amplitude drops to one-quarter of its initial value,
1/4=Aeλt.
Solving for the time,
t=1/λlog(1/4)=20.4s
Comparing this result with the period,
t=102.7T.
The maximum displacement or distance made by a point on a vibrating body or wave relative to its equilibrium location is known as the amplitude in physics. It is equivalent to the length of the vibration path divided in half. Amplitude is the separation between the wave's resting position and its highest displacement. Frequency is the number of waves that cross a particular place in a second. Period—the length of time needed for a wave cycle to complete
Learn more about amplitude here:
https://brainly.com/question/9525052
#SPJ4
7. An engineer is investigating potential energy with two identical magnetic roller coaster cars on different sides of a center magnet that cannot move. To test her ideas, the engineer will move one car one space. Which movement will result in the largest increase in potential energy?.
The same change in potential energy will be produced by each of these actions because they all move a roller coaster car by the same amount of space.
What is potential energy, exactly?
Due to its position, an object has the ability to store energy. The bow has no energy stored when it assumes its normal position. The bow can yet store energy when its position is changed from its normal equilibrium position because of its position. Potential energy is the energy of position that a thing has stored inside it.
Because the train is moving against the magnetic pull, the potential energy is increased. However, because the magnets in the system are unchanged, the potential energy is unaffected. Engineer is testing two identical magnetic roller coaster vehicles on either side of a stationary center magnet.
To learn more about potential energy use link below:
https://brainly.com/question/14427111
#SPJ4
A 10.0 kg block is released from rest down a 30° ramp.
It slides 6.0m along the ramp against a frictional force
of 16N. What is its speed after sliding 6.0m along the ramp?
*SOLVE USING ENERGY
Answer:
6.298 m/s
Explanation:
[tex]F_{net} =ma[/tex]
[tex]F_F=u_k*F_N[/tex] friction force equation
[tex]ma=mgsin(x)-umgcos(x)[/tex]
We are given
[tex]m=10\\g=9.81\\F_F=16\\V_i=0[/tex]
[tex]umgcos(x)=F_F[/tex]
[tex]u*10*9.81*cos(x)=16[/tex]
[tex]u=0.18833036[/tex]
[tex]ma=mgsin(x)-umgcos(x)[/tex]
[tex]10*a=10*9.81*sin(30)-0.18833036*10*9.81*cos(30)[/tex]
[tex]a=3.305[/tex]
[tex]V_{f} ^{2} =V_{i} ^{2}+2ax[/tex]
[tex]V_{f} ^{2} =0 ^{2}+2*3.305*6[/tex]
[tex]V_f=6.298[/tex]
an 8.0-newton wooden block slides across a horizontal wooden floor at constant velocity. what is the magnitude of the force of kinetic friction between the block and the floor?
Answer:
2.4 n
Explanation:
The force of kinetic friction between the block and the floor is given by:
where
is the coefficient of kinetic friction
N is the normal reaction of the floor against the block
For a horizontal surface (as in this case), the normal reaction is equal to the weight of the block, so . For wood-wood contact, the coefficient of kinetic friction is approximately . Therefore, the force of kinetic friction between the block and the
A capacitor is charged and then made to discharge through a resistance. The time constant is Ï„. In what time will the potential difference across the capacitor decrease by 10%?
a. t ln 0.1
b. t in 0.9
c. t ln 10/9
d. t in 11/10
Answer:
Q = Q0 e^-t/RC = Q0 e^-t/T
Charge left on capacitor after time t where T is the time constant of the capacitor - R * C
Q / Q0 = .9 charge decreases by 10%
.9 = e^-t/T
ln .9 = -t / T = .10
Or t = -T * ln .9
When elapsed time t = -ln .9 * time constant
Two identical blocks are pushed up frictionless inclines as shown. Consider the portion of the motion of block 1 during which it moves a distance L1, and the portion of the motion of block 2 during which it moves a distance L2. Each block is displaced the same vertical distance Z.The hand pushes parallel to the incline with same magnitude of force FBH in both cases. Block 2 moves at a decreasing speed. Is the absolute value of the work done by the gravitational force on block 2 greater than, less than, or equal to the work done by the gravitational force on block 1? Explain.
The answers to these questions are:
The absolute value of the work done by hand on block 1 is less than the absolute value of the work done by the hand on block 2. The force by hand is the same on both blocks but the distance traveled by the block 1 along the incline (L2) is greater than the distance traveled by the block 1 ( L1).The absolute value of the work done by the gravitational force on block 1 is equal to the absolute value of the work done by the gravitational force on block 2. Both blocks travel the same height Z.The speed of block 2 increases. The net work done on block 2 is not zero as in the case of block 1. Hence the speed of the block increases.Therefore, Two identical blocks are pushed up frictionless .
To know more about friction, visit:
https://brainly.com/question/24338873
#SPJ4
Two charged particles repel each other with a force f. If the charge on only one of the particles is doubled and the distance between them is also doubled, then the force will be?.
The square of the distance between the two charges has an inverse relationship with the force's size. As a result, when the gap between two charges is doubled, the attraction or repulsion weakens and drops to one-fourth of its initial strength.
What is force?An object's push or pull is seen as exerting a force. The interaction of the objects produces push and pull.
An external force is an agent that has the power to alter the resting or moving condition of a body. It has a direction and a magnitude. The application of force is the location at which force is applied, and the direction in which the force is applied is known as the direction of the force.
A spring balance can be used to calculate the Force. Newton is the SI unit of force (N).
What are repulsion force?The interaction between two or more comparable or similar charges to produce force. Repulsion between similar charges occurs. Charges that resemble one another separate from one another. Chemical bonding involves repulsive forces.
Know more about charged particle:
brainly.com/question/18763828
#SPJ4
As you watch the video, notice that the size of the tidal bulges varies with the Moon's phase, which depends on its orbital position relative to the Sun. Which of the following statements accurately describes this variation?
Low tides are lowest at both full moon and new moon.
Low tides are highest at both full moon and new moon.
High tides are highest at full moon and lowest at new moon.
Low tides are highest at full moon and lowest at new moon.
High tides are highest at both full moon and new moon.
High tides are highest at first- and third-quarter moon.
The size of the tidal bulges increases as the Moon moves closer to the Earth in its orbit, when it is in the new moon or full moon phase, and decreases as it moves away from the Earth in its orbit, when it is in the first quarter or third quarter phase.
What is tidal bulges?
The fluid and moveable ocean water is drawn towards the moon by the gravitational influence between the moon as well as the Earth. The ocean closest to the moon experiences a "bulge" as a result, as the Earth rotates, the affected waters' locations shift. Imagine the moon as just a magnet drawing the water to it. The force of intertia, which tends to keep an object moving inside a straight line, opposes this motion of the water in the direction of the moon. Our oceans' motion is balanced by this, but since the gravitational pull seems to be stronger, the resulting force also creates our tides.
To learn more about tidal bulges
https://brainly.com/question/4168632
#SPJ4
a generator is connected to a resistor and a 0.027-h inductor in series. the rms voltage across the generator is 9.2 v. when the generator frequency is set to 180 hz, the rms voltage across the inductor is 3.2 v. determine the resistance of the resistor in this circuit.
The resistance of the resistor in this circuit is 82.31 Ohms
How to solve for the resistanceWe would first have to solve for the angular frequency
ω = 2π* f
f = 180 hz
= 2* 3.14 * 180
= 1130.4
Next we would have to solve for the Inductive reactance XL = ω* L
= 1130.4 * 0.027
= 30.52
The current is
3.2 v / 30.52
= 0.1048
Impedance Z = V/ I
9.2 v / 0.1048
= 87.79
To get the resistance we would have to use
Z² = (R² + XL²)
87.79² = R² + 30.52²
R² = 87.79² - 30.52²
= 7707.08 - 931.47
= 6775.6
R = √6775.6
= 82.31 ohms
Read more on resistor here : https://brainly.com/question/24858512
#SPJ1
Sound 1 has an intensity of 40.0 W/m^2 . Sound 2 has an intensity level that is 2.0 dB greater than the intensity level of sound 1.
What is the intensity of sound 2?
l2= ? W/m^2
The intensity level of sound 2 is 63.386 W/m².
Intensity of sound 1 = 40.0 W/m²
Intensity of sound 2 = 2.0 dB
We know that I₁ = 10⁻¹² W/m²
Intensity level of sound 2 =
= Using the equation of the sound level intensity
= Iₓ = 10log (I/I₁)
= Iₓ = 10 log(40/ 10⁻¹²)
= Iₓ = 136.02 dB
Given that intensity of sound 2 is greater than sound 1 by 2.0 dB
Thus,
= Iₙ = 136.02 + 2.0
= Iₙ = 138.02 dB
To calculate intensity of sound 2 =
= I₂ = 10log(Iₙ / 10⁻¹²)
= I₂ = 63.386 W/m²
To know more about Intensity of Sound:
https://brainly.com/question/12899113
#SPJ4
a bicycle wheel with radius 0.3 m rotates from rest to 3.1 rev/s in 5.7 s. what is the magnitude (in m/s2) of the total acceleration vector at the edge of the wheel at 1.2 s?
The magnitude of the total acceleration vector at the edge of the wheel at 1.2 s is 5.22 m/s².
Given that,
Radius of the wheel = 0.3 m
Initial angular velocity ω₀ = 0
It rotates 3.1 rev/s in 5.7s. Therefore, ω = 2*π*r = 2*π* 3.1 = 19.47 rad/s
We know that, ω = ω₀ + αt
where, α = angular acceleration
ω = Final angular velocity
t = time
α = 19.47/5.7 = 3.42 rad/s²
Total acceleration at any point will be a vector sum of tangential acceleration and centripetal acceleration
ω = ω₀ + αt
ω = 0 + 3.42* 1.2 = 4.11 rad/s
αc = ω² * r = 4.11² * 0.3 = 5.07 m/s²
Tangential acceleration αt = α * r
αt = 4.11 * 0.3 = 1.23 m/s²
α net = √(5.07² + 1.23²) = √(25.7049 + 1.5129) = 5.22 m/s²
Thus, the magnitude of total acceleration vector at the edge of the wheel is 5.22 m/s².
To know more about acceleration:
https://brainly.com/question/14369333
#SPJ4
i have no clue on what to do
Answer:
Explanation:
what are the multiple answers -.-?
a single conducting loop has a radius equal to and carries a current equal to what is the magnitude of the magnetic field on the line through the center of the loop and perpendicular to the plane of the loop
On a current loop, a uniform magnetic field has a net torque but no net force. Let's assume that the magnetic field is parallel to both sides of the loop's two sides and is in its plane. The force on the left and right sides of the loop, if it has width a, height b, and current I, is given by F = IbB. Due to the field's parallel alignment with those other sides, they are not subject to any force.
No net force exists because the two forces are acting in opposite directions, but there is a torque that tends to cause the loop to rotate about an axis that passes through its center. This axis's torque is given by:
τ = F (a/2) + F (a/2) = Fa = IabB.
The area vector is perpendicular to the plane of the loop, so = IAB. Another right-hand rule can be used to determine its direction: curl your right hand's fingers in the direction of the current, and point your thumb outward so that it faces the direction of the area vector.
To know more about magnetic field visit:-
https://brainly.com/question/14848188
#SPJ4
if a river has an average width of 15 m, an average depth of 5 m, and is flowing with a velocity of 2 m/s, what is its discharge?
According to the given statement a river has an average 3 * 10⁵ W is its discharge.
What is velocity definition with example?The scalar metric of speed and direction of motion is known as velocity. The speed that an object goes in one side is known as its velocity. Speed may be used to calculate both the vehicle speed traveling north just on main freeway and the velocity of a explosion bursting in space.
Briefing:Water's speed is 2 m/s.
Flow area = 5m x 15m = 75m²
Water has a density of 1000 kg/m³
The volume of water flowing per second in the continuity equation is written as v=Av.
Hence, mass of water m=vρ=Avρ
K.E. = 1/2 mv² = 1/2 Avρ²
K.E. = 1/2 Avρ³
ρ = 1/2 Avρ³
ρ = 1/2 * 75 * (2)³ * 1000
ρ = 3 * 10⁵ W
To know more about Velocity visit:
https://brainly.com/question/28738284
#SPJ4
the 5.2 kg mass and spring are moved to a frictionless 30 degree incline, and positioned so that he psring is parlelle to the incline. determine the spring's new dpslacement at equilibrium
The displacement would be approximately 2.83 meters.
What is displacement?
A displacement is indeed a vector in geometry as well as mechanics that has a length equal to the shortest distance between a point P's initial and final positions. It measures the length and angle of the net motion, or total motion, in a straight line from the starting point to the destination of the juncture trajectory. The translation that links the starting point and the ending point can be used to spot a displacement. The finishing position xf of the a point relative towards its initial position xi, or a physical location (resulting from of the motion), is another way to describe a displacement. The difference between both the final and initial positions can be used to define the corresponding displacement vector:
The spring's new displacement at equilibrium depends on the angle of the incline. Since the incline is 30 degrees, the displacement of the spring at equilibrium can be found by using the following equation:
Displacement = (mass * gravity * sin(incline angle)) / spring constant
In this case, the displacement would be (5.2 kg * 9.8 m/s2 * sin(30))/ spring constant. Plugging in the values we know, the displacement would be approximately 2.83 meters.
To learn more about displacement
https://brainly.com/question/14422259
#SPJ4
a 10 kg mass slides from an initial velocity of 20 m/s to rest over 30 m. what is the force of friction?
Force of friction is 0.167
What is friction?The force preventing sliding against one another of solid surfaces, fluid layers, and material components is known as friction.
What is importance of friction?Things can move more slowly and become immobile when there is friction. In a world without friction, more things would slide around, it would be challenging to keep shoes and clothing on, and it would be extremely challenging for people or cars to move or turn.
According to the given information :
Mass=10 kg
Initial velocity(u)=20m/s
F=−μN
ma=−μmg
a=−μg
Distance travelled force coming to rest=30m
v²−u²=2as
0²−u²=2as
−u²=−2μgs
μ=(10)²/2×10×30=1/6=0.167
μ=0.167
To learn more about friction:
https://brainly.com/question/28356847
#SPJ4
if an astronaut knocks a wrench off the outside of the space shuttle (while in space) while she is doing a repair job, the wrench will continue moving in the same direction. which of newton's laws of motion will the wrench demonstrate?
The Newton's first law is demonstrated over here.
If the wrench is thrown then that wrench will keep on moving in the space.
As we all no space has no gravity and since there is no gravity, hence, no force is applied on that body.
The wrench will move freely in the space and will continue to move in same direction until there is some external force is applied to stop or change its direction.
This shows that over here the Newton's first law is applied.
The Newton's first law states that the body will continue to be in the same state or motion and will not change until the external force is applied on it.
This Newton's first law is also known as law of inertia.
Therefore, the wrench will continue to move in the same direction under the influence of Newton's first law.
To know more about Newton's first law, refer: https://brainly.com/question/974124
#SPJ4
what is the difference between the pressure on the bottom of a pool and the pressure on the water surface?
Due to the weight of the water on the body that is submerged, the pressure is higher at the bottom and lower at the surface.
How does pressure change with ocean depth?Our bodies experience a 14.7 pound per square inch air pressure while we are at sea level. Since your body's internal fluids are also pushing outward with equal force, you cannot feel it.But if you go even a few feet under the surface of the water, something changes. The pressure in your ears is getting worse. The hydrostatic pressure, or the force a liquid exerts on an object per unit area, has increased, which is the cause of this. The pressure of the water pressing down on you increases the deeper you go under the water. As you descend, the pressure rises by one atmosphere for every 33 feet (10.06 meters).Numerous sea creatures can withstand high pressure with no problems at all. Because of their more flexible bodies, whales, for example, can withstand extreme pressure changes. The loose, bendable cartilage that holds their ribs together prevents their rib cage from collapsing at pressures that would easily snap our bones.In order to prevent rupturing, a whale's lungs can also safely collapse under pressure. As a result, sperm whales can now go in search of giant squid at depths of up to 7,000 feet.To Learn more About pressure refer to:
https://brainly.com/question/28012687
#SPJ4
a parallel-plate air capacitor of capacitance 245 pf has a charge of magnitude 0.148/lc on each plate. the plates are 0.328 mm apart. (a) what is the potential difference between the plates? (
The potential difference between the plates of a parallel-plate air capacitor of capacitance 245 pf has a charge of magnitude 0.148 μC on each plate is 604 V
Q = C V
Q = Charge
C = Capacitance
V = Potential difference
Q = 0.148 μ C
Q = 0.148 * 10⁻⁶ C
C = 245 pF
C = 245 * 10⁻¹² F
V = Q / C
V = ( 0.148 * 10⁻⁶ ) / ( 245 * 10⁻¹² )
V = 604 V
Voltage, also known as electric pressure, electric tension, or potential difference, is the difference in electric potential between two points. In a static electric field, it corresponds to the work needed per unit of charge to move a test charge between the two points.
Therefore, the potential difference is 604 V
To know more about potential difference
https://brainly.com/question/12198573
#SPJ4
A 2.00-kg rock has a horizontal velocity of magnitude 12.0 m/s when it is at point P in the figure (Figure 1). (a) At this instant, what are the magnitude and direction of its angular momentum relative to point O? (b) If the only force acting on the rock is its weight, what is the rate of change (magnitude and direction) of its angular momentum at this instant?
The rate of change (magnitude and direction) of its angular momentum at this instant is 115 kg m/s².
The rate of change of angular momentum is equal to the net torque acting on the rock. The only force acting on the rock is the weight of the rock that is, mg.
As torque is equal to the product of the tangential component of force (
and distance (r) from the axis of rotation to the line of force, the net torque acting on the rock is,
Here, r is the distance from point O to the line of force.
This torque is equal to the rate of change of angular momentum of the rock.
Calculation:-
torque = mgcosθ
τ = mgrcosθ
= 115 kg m/s²
The magnitude of angular momentum is 115 kg m/s².
Learn more about angular momentum here:-https://brainly.com/question/4126751
#SPJ4
if it takes a bike wheel 6 seconds to complete one revolution, what is the wheel's angular velocity? answer: degree/s.
The angular velocity of the wheel when the bike takes 6 s to complete one revolution is 0.33π
Time taken by the wheel = t = 6 s
Angle of the wheel = θ
= θ = 2π
Angular Velocity = ω =
= ω = angle / time taken
= ω = θ / t
= ω = 2π / 6
= ω = π/3
= ω = 0.33π
Angular velocity is how fast the rigid body rotates with respect to its centre of rotation and is independent to the choice of origin. It is the displacement of the object revolving with respect to the time taken by the object.
To know more about Angular Velocity :
https://brainly.com/question/16272235
#SPJ4
Oil is spilled from an oil rig in the Gulf of Mexico andspreads in a circle with the circumference changing at a rate of 40m/sec. How fast is the area of the spill increasing when thecircumference of the circle is 100Ï€ meters?
The area of the spill increasing when the circumference of the circle is 100π meters at a rate of 2000 sq. m/sec.
What is circumference ?In geometry, the perimeter of a circle or ellipse is its circumference. In other words, the circumference would equal the length of the arc if the circle were expanded up and straightened out to a line segment.
The term "perimeter" is most frequently used to describe the radius of any closed shape. The exact location of the circle, which corresponds to the edge of a disc, is also referred to as its circumference.
Given parameters:
circumference changing at a rate = 2π dr = 40m/sec.
the circumference of the circle is = 2πr = 100π meters
Hence, the rate of area of the spill increasing = 2πrdr
= 100π meters × 40m/sec/2π
= 2000 sq. m/sec.
Learn more about circumference here:
https://brainly.com/question/27812873
#SPJ1
170 students sit in an auditorium listening to a physics lecture. Because they are thinking hard, each is using 125 W of metabolic power, slightly more than they would use at rest. An air conditioner with a COPof 5.0 is being used to keep the room at a constant temperature. What minimum electric power must be used to operate the air conditioner?
The calculated power is P = 3500 W. Power can be defined as the amount of work completed in a given amount of time.
Watt (W), which is derived from joules per second (J/s), is the SI unit of power. Horsepower (hp), which is roughly equivalent to 745.7 watts, is a unit of measurement sometimes used to describe the power of motor vehicles and other devices.
There are n = 140 students in the auditorium overall.
Each pupil is using a metabolic power of p = 125 W.
To keep the temperature in the auditorium consistent, the air conditioner's coefficient of performance (COP) is listed as 5.
Let P represent the required minimum amount of electric power to operate the air conditioner.The fact that
np = P in COP
P = np/COP
= ( 140 x 125 ) / 5
= 3500 W
Learn more about power here-
https://brainly.com/question/27877700
#SPJ4
now the switch for coil 1 has been closed for a long time. which direction is the induced current in coil 2 through the current meter while the switch for coil 1 stays closed?.
This causes a force to be exerted on the electrons in coil 2, resulting in induced current flowing in the opposite direction.
What is force?
A force is indeed an influence that can alter an object's motion according to physics. A force may cause an object to mass to accelerate when it changes its velocity, such as when it moves away from rest. An intuitive way to describe force is as a push or even a pull. A force is a vector quantity because it has both direction and magnitude. It is calculated using the newton SI unit (N). Force is denoted by the letter F. (formerly P). The net force acting on an object seems to be equal to the speed that its momentum changes over time, according to Newton's second law in its original formulation.
The induced current in coil 2 will be in the opposite direction as the current in coil 1. This is because when the switch for coil 1 is closed, current will start flowing through coil 1. This will create a magnetic field around coil 1, which intersects with the magnetic field around coil 2. This causes a force to be exerted on the electrons in coil 2, resulting in induced current flowing in the opposite direction.
To learn more about force
https://brainly.com/question/12785175
#SPJ4
What are the total force and aboute preure on the bottom of a wimming pool 22m by 8. 5cm whoe uniform depth i 2m? what will be the preure againt the ide of the pool near the bottom?
19600N[tex]m^{2}[/tex] is the total pressure near the bottom of the pool as per the given data in the statement.
What is pressure?Pressure: The perpendicular force applied to surface of any object tending to be distributed per unit area is known as pressure.
According to the given data :
length of the pool = 22m
breadth of the pool =8.5 cm=0.085 m
depth =2 m
To find the pressure near the bottom of the pool we use the following formula
P=hpg, where h=height or depth, p= density of liquid and g= 9.8m/s
P=2*1000*9.8
P=19600N[tex]m^{2}[/tex]
Hence, 19600N[tex]m^{2}[/tex] is the total pressure near the bottom of the pool as per the given data in the statement.
To know more about the pressure visit.
https://brainly.com/question/14082296
#SPJ4
19600N[tex]m^{2}[/tex] is the total pressure near the bottom of the pool as per the given data in the statement.
What is pressure?Pressure: The perpendicular force applied to surface of any object tending to be distributed per unit area is known as pressure.
According to the given data :
length of the pool = 22m
breadth of the pool =8.5 cm=0.085 m
depth =2 m
To find the pressure near the bottom of the pool we use the following formula
P=hpg, where h=height or depth, p= density of liquid and g= 9.8m/s
P=2*1000*9.8
P=19600N[tex]m^{2}[/tex]
Hence, 19600N[tex]m^{2}[/tex] is the total pressure near the bottom of the pool as per the given data in the statement.
To know more about the pressure visit.
https://brainly.com/question/14082296
#SPJ4
The materials that made up the solar nebulacan be categorized into the four general types as follows. Rank these meals from left to right based on the dance in the solare forest to lowest ► View Available Hints Reet Help metals rock hydrogen compounds hydrogen and hellum gas Lowest abundance Highest abundance
The materials arranged in order lowest to highest abundance are as follows
Metals> Rocks> Hydrogen compounds >Hydrogen and Helium
The solar nebula begins as a thin gas of hydrogen and helium that is covered in little dust specks. The planets' building blocks are these little grains. Any gas cloud's development depends significantly on the movement of dust particles. These grains serve as the condensation nuclei on which matter accretes.
The solar nebula is composed of 98% light gases, including hydrogen and helium, which were created during the Big Bang. Next, 1.4% of hydrogen compounds, such as water, methane, and ammonia, were found. Finally, 0.4% of rocks, such as silicates, and 0.2% of metals, such as iron, nickel, and aluminum, were found.Due to the intense heat, only metals and rocks could condense in the nebula's interior, while hydrogen compounds, despite being more prevalent, could only do so in the cooler outer regions.
Click here to learn more about the solar nebula.
https://brainly.com/question/28715616
#SPJ4
A 1270 kg sedan has the same amount of momentum as a 3600 kg truck moving with a speed of 14 m/s what is the speed of the sedan
The speed of sedan is 39.68m/s.
What is momentum?By dividing a particle's mass by its speed, momentum is produced. Momentum is a vector quantity because it has both a direction and a magnitude. Isaac Newton's second law of motion states that the time rate of change of momentum is equal to the force acting on the particle. the laws of motion established by Newton.
Momentum = mass × velocity
Momentum of the truck = 3600 × 14
Momentum of the truck = momentum of sedan
3600 × 14 = 1270 × speed
Speed of sedan = 3600 × 14/1270
Speed of sedan = 39.68m/s.
To know more about momentum visit:
https://brainly.com/question/24030570
#SPJ1
PLEASE HELP WILL MARK BRAINLIEST IF YOU EXPLAIN HWK YOU GOT THE ANSWER!!!!
Answer:
A A A A. a. a a a a a a a
Explanation:
a is the answer
a boat is traveling at 54 knots in a direction of 48°. it encounters wind moving at 14 knots in a direction of 20°. what is the true velocity and direction of the boat? round to the nearest whole number.
The true velocity and direction of the boat is 67knots, 42degree.
Velocity is the directional pace of an item in motion as an indication of its rate of exchange in the role as determined from a selected frame of reference and as measured by way of a selected standard of time.
Average velocity is calculated by means of dividing your displacement (a vector pointing out of your initial role in your final position) through the entire time; the average pace is calculated by way of dividing the overall distance you traveled by means of the total time.
Calculation:-
velocity of boat = 54 knots
direction = 48°
wind speed = 14 knots
direction = 20°.
The true velocity and direction of the boat is 67knots, 42degree
Learn more velocity here:-
https://brainly.com/question/1844960
#SPJ4
Answer:
67 knots; 42°
Explanation:
I took the test and got it right:)
when a submarine dives to a depth of 120 m, to how large a total pressure is its exterior surface subjected? the density of seawater is about 1.03 g/cm3.
Data provided in the question:
Initial depth of the submarine, d = 120 m
Density of water, ρ = 1.03 kg/m³
Now,
Pressure due to water = ρgh
here,
g is the acceleration due to gravity = 10 m/s²
h = height of water above
So,
Increase in pressure = ρgD - ρgd
= ρg(D - d)
= 1.03 × 10 × (120)
= 1236 Pa
Therefore, the total pressure of the submarine is 1236 Pa.
To know more about pressure, refer: https://brainly.com/question/14640642
#SPJ4
Which state of equilibrium is a person in while running on a treadmill?
Answer: Dynamic equilibrium.
Explanation: When a person is running on a treadmill, they are in a state of dynamic equilibrium. Dynamic equilibrium occurs when a system is in constant motion and the forces acting on the system are balanced. In this case, the person is in motion (running on the treadmill) and the forces acting on them (gravity and the force of the treadmill belt) are balanced, allowing them to maintain their motion at a constant speed.