Answer:
v’ =( [tex]\frac{1}{1+ \frac{M}{m} }[/tex] ) v
we see that the greater the difference, the more the sled slows down.
friction force
Explanation:
When the man pushes the sled he does work and the sled acquires a speed and as long as it is supplied with an energy equal to the work of the chipping force with the snow, the speed is maintained.
When he jumps on the sled, a collision occurs and the initial moment
p₀ = mv
is increased by the increase in mass
m_f= (m + M_{man} ) v '
In this case there is no longer any external force applied and the only external force is friction, which causes the sled to stop, even when it is small, but the significant reduction in speed is due to the increase in masses.
p₀ = p_f
mv = (m + M_{man}) v '
v ’= [tex]\frac{m}{m+M}[/tex] v
v’ =( [tex]\frac{1}{1+ \frac{M}{m} }[/tex] ) v
Therefore, we see that the greater the difference, the more the sled slows down.
The only forces that act on the sled with the man are the friction that is responsible for the decrease in speed and weight with the normal
A flat loop of wire consisting of a single turn of cross-sectional area 8.80 cm2 is perpendicular to a magnetic field that increases uniformly in magnitude from 0.500 T to 1.80 T in 1.10 s. What is the resulting induced current if the loop has a resistance of 2.20
Answer:
The magnitude of the induced current is 4.73 x 10⁻³ A.
Explanation:
Given;
number of turns, N = 1
cross sectional area of the loop, A = 8.8 cm² = 8.8 x 10⁻⁴ m²
change in magnetic field strength, ΔB = 1.8 T - 0.5 T = 1.3 T
change in time, Δt = 1.10 s
resistance of the loop, R = 2.2 ohm
The magnitude of the induced emf is calculated as;
[tex]emf = \frac{NA \Delta B}{\Delta t} \\\\emf = \frac{1 \times 8.8\times 10^{-4} \times 1.3}{1.10} \\\\emf = 1.04 \times 10^{-3} \ V[/tex]
The induced current in the loop is calculated as;
[tex]I = \frac{emf}{R} \\\\I = \frac{1.04 \times 10^{-3}}{2.2} \\\\I= 4.73 \times 10^{-4} \ A[/tex]
Therefore, the magnitude of the induced current is 4.73 x 10⁻³ A
200 Coulombs of charge passes through a point in a circuit for 0.6 minutes. what is the magnitude of the current flowing
Answer:
5.56 A
Explanation:
From the question,
Q = it.............. Equation 1
Where Q = charges, i = current, t = time.
Make i the subject of the equation
i = Q/t.............. Equation 2
Given: Q = 200 coulombs, t = 0.6 minutes = (0.6×60) seconds
Substitite these values into equation 2
i = 200/(0.6×60)
i = 5.56 A
Hence the magnitude of the current flowing through the circuit is 5.56 A
Which statement about oceans is incorrect?
A Evaporation occurs when water is warmed by the sun.
B Most evaporation and precipitation occur over the ocean.
C 97 percent of Earth's water is fresh water from the ocean.
D Water leaves the ocean by the process of evaporation.
An electron, moving toward the west, enters a uniform magnetic field. Because of this field the electron curves upward. The direction of the magnetic field is An electron, moving toward the west, enters a uniform magnetic field. Because of this field the electron curves upward. The direction of the magnetic field is downward. towards the west. upward. towards the south. towards the north.
Answer:
towards the north.
Explanation:
The uniform magnetic field has strength and direction in all points. The upwards motion of the field or he electronic curves will show a northern direction. Hence, the field can be created by taking the opposite magnetic in the two directions. The straight line of motion of the field will indicate the flow in the north direction. The magnetic field lines will remain parallel and stay uniform to poles.What happens when a moving object experiences no net force?
Answer:
An object with no net forces acting on it which is initially at rest will remain at rest. If it is moving, it will continue to move in a straight line with constant velocity. Forces are "pushes" or "pulls" on the object, and forces, like velocity and acceleration are vector quantities.
When an object is raised vertically, work is done against __________. What one word completes the sentence?
please help quickly!!
When an object is raised vertically, work is done against _gravitational force _________
What is gravitational force ?The force of attraction between all masses in the universe; especially the attraction of the earth's mass for bodies near its surface is called gravitational force .
On every body there is a force acting named gravitational force which attracts the body downward .
If a object / body is thrown up it always comes downward if only gravitational force is acting on it which act due to earth's gravity .
When an object is raised vertically, work is done against _gravitational force _________
learn more about gravitational force :
https://brainly.com/question/12528243?referrer=searchResults
#SPJ2
Why are dominant alleles always shown as capital letters?
Answer:
When writing a genotype, the dominant allele is usually represented by a capital letter, while the recessive allele has a lowercase letter.
Explanation:
Please mark me brainlest.
Answer:
Because in a punnett square, dominant alleles need to be differentiated from the recessive alleles, to do this, we write the dominant alleles as capital letters.
Explanation:
Yanni just turned one. He loves to play with his cars and trucks. He can also name the animals he sees in books.
In which stage of development is Yanni?
childhood
infancy
adolescence
adulthood
Missy Diwater, the former platform diver for the Ringling Brother's Circus had a kinetic energy of 15,000 J just prior to hitting the bucket of water. If Missy's mass is 50 kg, then what is her speed?
Answer:
24.5 m/s
Explanation:
KE=1/2mv^2
15000=1/2(50)v^2
30000=(50)v^2
600=v^2
sqrt600=v
v=24.5 m/s!!
What is the unique geological feature found on Mercury surface?
Answer:
The surface of Mercury has landforms that indicate its crust may have contracted. They are long, sinuous cliffs called lobate scarps. These scarps appear to be the surface expression of thrust faults, where the crust is broken along an inclined plane and pushed upward.
Explanation:
I hope this helps a little bit.
Joe has a mass of 110 kg. If Joe has to climb a 10 m ladder to get to the top of a chimney, how much work did do?
A 1000 kg truck moving at 2.0 m/s runs into a concrete wall. It takes 0.5 s for the truck to completely stop. What is the magnitude of force exerted on the truck during the collision?
Answer:
Momentum is given by
p
=
m
v
. Impulse is the change of momentum,
I
=
Δ
p
and is also equal to force times time:
I
=
F
t
. Rearranging,
F
=
I
t
=
Δ
p
t
=
0
−
20
,
000
5
=
−
4000
N
.
Explanation:
Momentum before the collision is
p
=
m
v
=
2000
⋅
10
=
20
,
000
k
g
m
s
−
1
.
Assuming the truck comes to a complete halt, the momentum after the collision is
0
k
g
m
s
−
1
.
The change in momentum,
Δ
p
, is initial minus final
→
0
−
20
,
000
=
−
20
,
000
This is called the impulse:
I
=
Δ
p
. Impulse is also equal (check the units) to force times time:
I
=
F
t
.
We can rearrange this expression to make
F
the subject:
F
=
I
t
=
Δ
p
t
=
−
20
,
000
5
=
−
4000
N
The negative sign just means the force acting is in the opposite direction to the initial momentum.
(This will be the average force acting during the collision: collisions are chaotic so the force is unlikely to be constant.)
Due to historical difficulty in delivering supplies by plane, one of your colleagues has suggested you develop a catapult for slinging supplies to affected areas, similar to the electromagnetic lift catapults used to launch planes from aircraft carriers. This catapult is located at a fixed point 400 meters away and 50 meters below the target site. The catapult is capable of launching the payload at 67 meters per second and an initial launch angle of 50 degrees. Using your knowledge of kinematics equations, determine whether this would be sufficient to deliver the payload to the drop site.
Answer:
Please see below as the answer is self-explanatory.
Explanation:
We can take the initial velocity vector, which magnitude is a given (67 m/s) and project it along two directions perpendicular each other, which we choose horizontal (coincident with x-axis, positive to the right), and vertical (coincident with y-axis, positive upward).Both movements are independent each other, due to they are perpendicular.In the horizontal direction, assuming no other forces acting, once launched, the supply must keep the speed constant.Applying the definition of cosine of an angle, we can find the horizontal component of the initial velocity vector, as follows:[tex]v_{avgx} = v_{o}*cos 50 = 67 m/s * cos 50 = 43.1 m/s (1)[/tex]
Applying the definition of average velocity, since we know the horizontal distance to the target, we can find the time needed to travel this distance, as follows:[tex]t = \frac{\Delta x}{v_{avgx} } = \frac{400m}{43.1m/s} = 9.3 s (2)[/tex]
In the vertical direction, once launched, the only influence on the supply is due to gravity, that accelerates it with a downward acceleration that we call g, which magnitude is 9.8 m/s2.Since g is constant (close to the Earth's surface), we can use the following kinematic equation in order to find the vertical displacement at the same time t that we found above, as follows:[tex]\Delta y = v_{oy} * t - \frac{1}{2} *g*t^{2} (3)[/tex]
In this case, v₀y, is just the vertical component of the initial velocity, that we can find applying the definition of the sine of an angle, as follows:[tex]v_{oy} = v_{o}*sin 50 = 67 m/s * sin 50 = 51.3 m/s (4)[/tex]
Replacing in (3) the values of t, g, and v₀y, we can find the vertical displacement at the time t, as follows:[tex]\Delta y = (53.1m/s * 9.3s) - \frac{1}{2} *9.8m/s2*(9.3s)^{2} = 53.5 m (5)[/tex]
Since when the payload have traveled itself 400 m, it will be at a height of 53.5 m (higher than the target) we can conclude that the payload will be delivered safely to the drop site.coefficient of viscosity of a glycerine is 8.4 poison explain
Answer:
coefficient of viscosity of 8.4 poison denotes that the tangential frictional force acting per unit area when divided by the velocity gradient as a result of streamline flow conditions gives 8.4.
Explanation:
Viscosity is defined as the extent to which a fluid can resist flow when a force is applied to it.
Now, coefficient of viscosity is the term in which viscosity is calculated. It is basically the tangential frictional force acting per unit area which is divided by the velocity gradient as a result of streamline flow conditions.
Thus, coefficient of viscosity of 8.4 poison denotes that the tangential frictional force acting per unit area when divided by the velocity gradient as a result of streamline flow conditions gives 8.4.
The local church is hosting a carnival which includes a bumper car ride. Bumper car A and its driver have a mass of 300 kg; bumper car B and its driver have a mass of 200 kg. Bumper car A has a velocity to the right of 2 m/s and bumper car B is at rest. At t = 0 s, bumper car A and B are separated by 10 m. Bumper car A accelerates at 1 m/s2 to a velocity of 4 m/s and continues at this constant speed until colliding with bumper car B.
Calculate the time required for bumper car A to travel the 10 m to collide with bumper car B.
Calculate the speed of bumper car A following the collision with bumper car B, which now has a velocity to the right of 3 m/s.
Is the direction of motion for bumper car A following the collision with bumper car B to the right, to the left, or is bumper car A at rest?
Is the collision elastic? Justify your answer.
Answer:
a. 20 s
b. 0 m/s
c. right
d.no its inelastic because when the car b was at rest and a was coming in at it, since b had no force what so ever car a swept it away with it moving to the right
Explanation:
im not sure though
By applying conservation of linear momentum, the answers are:
1. Time = 2 s
2. 3 m/s
3. same direction
4. Inelastic collision
COLLISIONThere are for types of collision. They are;
Elastic CollisionPerfectly elastic collisionInelastic collisionPerfectly Inelastic collisionGiven that a local church is hosting a carnival which includes a bumper car ride. Bumper car A and its driver have a mass of 300 kg; bumper car B and its driver have a mass of 200 kg. Bumper car A has a velocity to the right of 2 m/s and bumper car B is at rest. At t = 0 s, bumper car A and B are separated by 10 m. Bumper car A accelerates at 1 m/s2 to a velocity of 4 m/s and continues at this constant speed until colliding with bumper car B.
1. The time required for bumper car A to travel the 10 m to collide with bumper car B can be calculated by using first equation of linear motion.
V = U + at
Where
V = 4 m/s
U = 2 m/s
a = 1 m/[tex]s^{2}[/tex]
Substitute all the parameters into the formula
4 = 2 + t
t = 4 - 2
t = 2s
2. To calculate the speed of bumper car A following the collision with bumper car B, which now has a velocity to the right of 3 m/s, we will apply conservation of linear momentum
[tex]m_{1}u_{1}[/tex] = [tex]m_{1}v_{1}[/tex] + [tex]m_{2}v_{2}[/tex]
300 x 4 = 300V + 200 x 3
1200 = 300V + 300
300V = 1200 - 300
300V = 900
V = 900/300
V = 3 m/s
3. Since the final velocity of car A is positive, the direction of motion for bumper car A follows the collision with bumper car B to the right.
4. Since the both move at the same velocity, the collision inelastic.
Learn more about Collision here: https://brainly.com/question/25121535
1. What does the Work-Energy Theorem state?
Work is equal to the change in kinetic energy
Work is equal to the change in momentum
Work is equal to the change in impulse
Work is equal to the change in position
The Work-Energy Theorem states that Work is equal to the change in kinetic energy, which is the first option . This theorem is an essential principle in physics and mechanics, so first option is correct.
Work (W) is a measure of the energy transferred to or from an object by a force acting on it. It is defined as the product of the force applied to the object and the displacement of the object in the direction of the force. When a force does positive work on an object, it transfers energy to the object, increasing its kinetic energy. Conversely, when a force does negative work on an object (opposite to its direction of motion), it takes energy away from the object, decreasing its kinetic energy. So, first option is correct.
Learn more about the work-energy theorem here.
https://brainly.com/question/30560150
#SPJ6
What x rays travel at the speed of
When you are driving on the freeway and following the car in front of you, how close is too close? Let's do an estimation.
1. Pick a car model (preferably the one you drive, but can also be any car of your dream), and find its stopping distance at highway speeds (you can usually find this type of data online).
2. Assuming that the car in front of you suddenly does a hard brake. For simplicity, assume that its braking performance is about the same as yours. Then also assume a reasonable amount of reaction time on your part (the time delay between seeing the brake lights lit up and applying your own brake). In order for you not to run into the car your are following, what's the closest distance you need to keep between the two cars?
3. Redo the same calculation if the vehicle in front of you is a typical big-rig truck. Find its braking data online.
4. There is a rule of thumb which says that you must stay one car length behind the car in front of you for every 10 mi/h of driving speed. From your calculation, does this rule make sense?
Answer:
1) v= 90km/h d = 70 m, 2) x₁ = v t_r, x₁ = 6.25 m, 3) x₁=6.25 no change
4) x = 22 m
Explanation:
1) for the first part, you are asked to find the minimum safety distance with the vehicle in front
The internet is searched for the stopping distance for two typical speeds on the highway
v (km/ h) v (m/s) d (m)
90 25 70
100 27.78 84
the safe distance is this distance plus the distance traveled during the person's reaction time, which can be calculated with infirm movement
v = x / t_r
x₁ = v t_r
the average reaction time is t_r = 0.25s for a visual stimulus and t_r 0.17 for an auditory stimulus
therefore the safe distance is
x_total = x₁ + d
2) The distance is the sum of the distance traveled in the reaction
x₁ = v t_r
for v = 90 km / h
x₁ = 25 0.25
x₁ = 6.25 m
for v = 100 km / h
x₁ = 27.78 0.25
x₁ = 6.95 m
the total distance is
x_total = x₁ + d
for v = 90 km / h
x_total = 25 0.25 + 70
x_total = 76.25 m
this is the distance until the cars stop and do not collide
3) the stopping distance of a truck is
v = 90 km / h d = 100 m
in this case we see that the braking distance is much higher,
the safe distance is given by the distance traveled during the reaction, as the truck brakes slower than the car this distance does not change
4) let's analyze the empirical rule: maintain the length of a car for each increase in speed of v = 10 m / h = 4.47 m / s
for the car case at v = 90km / h = 25 m / s
according to this rule we must this to
x = 25 / 4.47 = 5.6 cars
each modern car is about 4 m long so the distance is
x = 22 m
we see that this distance is much greater than the reaction distance so it does not make much sense
a guitar string transmits waves at 509 m/s. to create a 491 Hz note, to what length should the guitar player shorten the string?
Answer:
Wavelength = 1.04 meters
Explanation:
Given the following data;
Speed = 509m/s
Frequency = 491Hz
To find the wavelength;
Wavelength = speed/frequency
Wavelength = 509/491
Wavelength = 1.04 meters
Therefore, the guitar player should shorten the length of the string to 1.04 meters.
Answer: 0.52
Explanation:
You are riding in the passenger seat of a car as it goes around a tight turn. You slide across the seat to the passenger side door. Which statement below properly describes what is happening? a. You are exerting a centripetal force on the door. b. The door and seat are exerting a centripetal force on you that balances the centrifugal force of the turn. c. The car seat exerts a centripetal force on you, but not enough to keep you in place, so the door exerts the rest. d. The centrifugal force is greater than the force of friction between you and the seat, so you slide outward.
Answer:
Explanation:
answer C looks good
there isn't really a "centrifugal " force. :/ when we are pushed "back" in a car seat.. it's not because there is a force pushing us backwards... but a force pushing us forwards.. just like when turning too, a force pushes us into the corner, not a force pushing out of the corner. :)
1. What is matter?
2. What are the three phases of matter?
3. Describe how gas particles move.
4. What is temperature?
5. The slower the particles, the ______________ the temperature.
6. A change in temperature causes what?
7. What is the difference between boiling and evaporation?
8. What is sublimation?
9. Name the three ways thermal energy is transferred.
10. Sunburn is an example of what?
11. Give an example of convection.
12. What is conduction?
13. What is the difference between conductors and insulators?
Answer:
1.matter is any substance that has mass and takes up space by having volume.
2.The three fundamental phases of matter are solid, liquid, and gas (vapour),
3.In gases the particles move rapidly in all directions, frequently colliding with each other and the side of the container. With an increase in temperature, the particles gain kinetic energy and move faster. ... In liquids, particles are quite close together and move with random motion throughout the container.
3.In gases the particles move rapidly in all directions, frequently colliding with each other and the side of the container. With an increase in temperature, the particles gain kinetic energy and move faster. ... In liquids, particles are quite close together and move with random motion throughout the container.
The following problem applies to questions 8 and 9: a glass window acquires a net negative charge on its surface after being cleaned. Particles of dust, which are usually charged positively, start accelerating toward the window. If a particle travels a distance of 1 meter before reaching the window, in a time duration of 10 sec, and if the mass of the particle is 1 micro-gram and the charge on the particle is 10-12 Coulomb, then the magnitude of the electric field intensity is Group of answer choices
Answer:
the magnitude of the electric field intensity is 20 N/C
Explanation:
Given the data in the question;
mass m = 1 micro gram = 1 × 10⁻⁹ kg
time duration t = 10 sec
distance s = 1 m
the charge on the particle q = 10⁻¹² Coulomb
force applied on a charged particle due to electric field E is;
F = Eq ------ equ 1
where q is the charge on the particle.
Also, force on a particle with mass m will be;
F = ma ------ equ
where a is acceleration
so F = ma = Eq
ma = Eq -------- equ 3
using kinetic equation
Distance = 1/2×at²
where a is acceleration and t is the time period
now lets consider that initial velocity is zero (0)
Here;
1 m = 1/2 × a × ( 10 s )²
1 m = a × 50 s²
a = 1 m / 50 s²
a = 0.02 m/s²
so, from equation 3
ma = Eq
E = ma / q
we substitute
E = (1 × 10⁻⁹ kg × 0.02) / 10⁻¹² Coulomb
E = 2 × 10⁻¹¹ / 10⁻¹²
E = 20 N/C
Therefore, the magnitude of the electric field intensity is 20 N/C
What is the weight of a 25 kg object on Earth with an acceleration due to gravity of 9.8m/s/s?
2.45 n
24.5 n
245 n
2450 n
Take 100 PONTS!!!!!! PLEASE I NEED HELP FAST. Just look The picture.
Answer:
i THINK it’s false. You don’t have to give me points ;-;
Explanation:
Answer:
i think false and true is spelt wrong lol
Explanation:
I want answer plzz??
Answer:
a=0.5g ms^-2
Explanation:
Let tension be T
acceleration be a
g be gravitational acceleration 9.81ms^-2
They share same T and a
by force diagram the net force on m:
T-2.1g=2.1a
net force on M:
6.3g-T=6.3a
solve:
(T-2.1g)/(6.3g-T)=2.1a/6.3a
3T+T=12.6g
T=3.15g newton
3.15g-2.1g=2.1a
a=0.5g ms^-2
3. A woman drove her car from home to her daughter's school. The odometre on her dashboard says she travelled 4.5 km to do this. She then immediately drove back home, using a different route, which was 5.5 km long. The whole journey took 30 minutes.
a. What distance did she travel?
b. What was her displacement?
C. What was her average speed during the journey?
Answer:
Look Below -->
Explanation:
a. She traveled 10 km, add 4.5 km + 5.5 km = 10 km (Distance is the total units travelled, so just add them all up :) )
b. Her displacement is 0 km because she went back home. (Displacement is the difference between the end and starting points)
c. 3 km/hr (30 minutes / 10 km)
The sun warms Earth through the process of _________
conduction
convection
insulation
radiation
what is the name for a force of gravity acting on an object
Answer:
Weight
Explanation:
We call it "Ralph" or "the object's weight".
Object A is moving due east, while object B is moving due north. They collide and stick together in a completely inelastic collision. Momentum is conserved. Object A has a mass of m A = 17.0 kg and an initial velocity of v 0A = 8.00 m/s, due east. Object B, however has a mass of m B = 29.0 kg and an initial velocity of v 0B = 5.00 m/s, due north. Find the magnitude and direction of the total momentum of the two-object system after the collision.
Answer:
pf = 198.8 kg*m/s
θ = 46.8º N of E.
Explanation:
Since total momentum is conserved, and momentum is a vector, the components of the momentum along two axes perpendicular each other must be conserved too.If we call the positive x- axis to the W-E direction, and the positive y-axis to the S-N direction, we can write the following equation for the initial momentum along the x-axis:[tex]p_{ox} = p_{oAx} + p_{oBx} (1)[/tex]
We can do exactly the same for the initial momentum along the y-axis:[tex]p_{oy} = p_{oAy} + p_{oBy} (2)[/tex]
The final momentum along the x-axis, since the collision is inelastic and both objects stick together after the collision, can be written as follows:[tex]p_{fx} = (m_{A} + m_{B} ) * v_{fx} (3)[/tex]
We can repeat the process for the y-axis, as follows:[tex]p_{fy} = (m_{A} + m_{B} ) * v_{fy} (4)[/tex]
Since (1) is equal to (3), replacing for the givens, and since p₀Bₓ = 0, we can solve for vfₓ as follows:[tex]v_{fx} = \frac{p_{oAx}}{(m_{A}+ m_{B)}} = \frac{m_{A}*v_{oAx} }{(m_{A}+ m_{B)}} =\frac{17.0kg*8.00m/s}{46.0kg} = 2.96 m/s (5)[/tex]
In the same way, we can find the component of the final momentum along the y-axis, as follows:[tex]v_{fy} = \frac{p_{oBy}}{(m_{A}+ m_{B)}} = \frac{m_{B}*v_{oBy} }{(m_{A}+ m_{B)}} =\frac{29.0kg*5.00m/s}{46.0kg} = 3.15 m/s (6)[/tex]
With the values of vfx and vfy, we can find the magnitude of the final speed of the two-object system, applying the Pythagorean Theorem, as follows:[tex]v_{f} = \sqrt{v_{fx} ^{2} + v_{fy} ^{2}} = \sqrt{(2.96m/s)^{2} + (3.15m/s)^{2}} = 4.32 m/s (7)[/tex]
The magnitude of the final total momentum is just the product of the combined mass of both objects times the magnitude of the final speed:[tex]p_{f} = (m_{A} + m_{B})* v_{f} = 46 kg * 4.32 m/s = 198.8 kg*m/s (8)[/tex]
Finally, the angle that the final momentum vector makes with the positive x-axis, is the same that the final velocity vector makes with it.We can find this angle applying the definition of tangent of an angle, as follows:[tex]tg \theta = \frac{v_{fy}}{v_{fx}} = \frac{3.15 m/s}{2.96m/s} = 1.06 (9)[/tex]
⇒ θ = tg⁻¹ (1.06) = 46.8º N of E
in a class where the number of girls is 36% of the total number,there are 48 boys.how many students are there in the class?
Answer:
There are 75 people in the class. The number of boys is 48 and the number of girls is 27. The percentage of girls is 36% of 75.
Explanation: