Answer:
211.2 kg:m/s
Explanation:
Mark brainily
where is a positive constant and is the acceleration due to gravity, is a model for the velocity of a body of mass that is falling under the influence of gravity. Because the term represents air resistance, the velocity of a body falling from a great height does not increase without bound as time increases. Use a phase portrait of the differential equation to find the limiting, or terminal, velocity of the body. Explain your reasoning.
Answer:
[tex]v_{T}[/tex] = [tex]\frac{b}{m}[/tex] g
Explanation:
For this exercise we use Newton's second law
∑ F = m a
where they relate it is
a = dv / dt
v = dx / dt
in this case we have two forces: the weight of the body and the friction of the air
fr -W = m a
there are several ways to approximate the friction force in a fluid, if the velocity of the body is low we can use
fr = b v
for high speeds, higher power speed terms are entered
we substitute
b v - m g = m dv / dt
[tex]\frac{dv}{dt}[/tex] = [tex]\frac{b}{m}[/tex] v -g
We can see that as the speed increases, we reach the point that the term on the right is zero, at this point there is no acceleration, therefore the speed is constant and is called the terminal velocity.
0 =[tex]\frac{b}{m} \ v_T[/tex] -g
[tex]v_{T}[/tex] = [tex]\frac{b}{m}[/tex] g
the constant b is given by the conditions of the air, pressure, density and temperature
A 5 kg block rests on a rough horizontal table. A rope is
attached to the block and is pulled with a force of 11N to the
left. As a result, the block accelerates at 2 m/s2. The coefficient
of kinetic friction between the block and the table is (round
to the nearest hundredth)
Answer:
Approximately [tex]0.02[/tex] (assuming that [tex]g = 9.81\; \rm N \cdot kg^{-1}[/tex], and that the block was initially moving to the left.)
Explanation:
Apply Newton's Second Law to find the net force on this block.
Mass of this block: [tex]m = 5\; \rm kg[/tex].
Acceleration of this block: [tex]a = 2\; \rm m \cdot s^{-2}[/tex].
[tex]\begin{aligned}\text{Net force} &= m \cdot a \\ &= 5\; \rm kg \times 2\; \rm m \cdot s^{-1} = 10\; \rm N\end{aligned}[/tex].
The block is moving and accelerating towards the left. Hence, friction (which opposes motion) would be towards the right and would be opposite to the direction of the [tex]11\; \rm N[/tex] pulling force.
Therefore, the expression for the net force on this object would be:
[tex](\text{Net force} ) = (\text{Pulling force}) - (\text{Friction})[/tex].
[tex]10\; \rm N = 11\; \rm N - (\text{Friction})[/tex].
Hence:
[tex]\text{Friction} = 11\; \rm N - 10\; \rm N = 1\; \rm N[/tex].
The question states that this table is horizontal. Weight of the block (downwards) and normal force from the table (upwards) are the only two forces on this block in the vertical direction. Hence, the magnitude of the normal force on this block would equal to that of the weight of the block:
[tex]\begin{aligned} |\text{Normal force}| &= |\text{Weight}| \\ &= m \cdot g \\ &= 5 \; \rm kg \times 9.81\; \rm N \cdot kg^{-1} = 49.05\; \rm N\end{aligned}[/tex].
Calculate the constant of kinetic friction between this block and the table:
[tex]\begin{aligned}\mu_{\text{k}} &= \frac{\text{Friction}}{\text{Normal force}} \\ &= \frac{1\; \rm N}{49.05\; \rm N} \approx 0.02\end{aligned}[/tex].
Which choices describe advantages of wind energy over fossil fuels?
Select all that apply.
doesn't emit pollutants
renewable
freely available
O releases carbon dioxide instead of carbon monoxide
The advantages of wind energy over fossil fuels are that it does not emit pollutants, it is a renewable source of energy and it is a freely available source of energy.
What is wind energy?
The process that describes the generation of wind power or the mechanical power using the flow of wind itself, is known as wind energy.
Following are the advantages of wind energy over fossil fuels -
Free source of fuel.One of the cleanest forms of energy.Advance technologies are used for its extraction.Does not disrupt any sort of farmland operations.It is a clean fuel source and does not emit pollutants.It is a renewable source of energy.Thus, we can conclude that the advantages of wind energy over fossil fuels are that it does not emit pollutants, it is a renewable source of energy and it is a freely available source of energy.
Learn more about wind energy here:
https://brainly.com/question/26117202
How is the chemical bonding within a molecule of carbon dioxide (CO2) different from the chemical bonding within a crystal of iron (Fe)?
A.
In an iron crystal, the atoms are joined by sharing electrons. In carbon dioxide, atoms of carbon and oxygen are held together by freely moving electrons.
B.
In a carbon dioxide molecule, atoms of carbon and oxygen are joined by sharing electrons. In an iron crystal, the atoms are held together by freely moving electrons.
C.
In an iron crystal, the atoms are joined by their opposite electrical charges. In carbon dioxide, atoms of carbon and oxygen are held together by freely moving electrons.
D.
In a carbon dioxide molecule, atoms of carbon and oxygen are joined by their opposite electrical charges. In an iron crystal, the atoms are held together by freely moving electrons.
Answer:
I'ts B
Explanation:
:p
The chemical bonding within a molecule of carbon dioxide (CO2) different from the chemical bonding within a crystal of iron (Fe) in a carbon dioxide molecule, atoms of carbon and oxygen are joined by sharing electrons. In an iron crystal, the atoms are held together by freely moving electrons. Therefore, option B is correct.
What is chemical bonding ?The term chemical bonding is defined as the formation of a chemical bond between two or more atoms, molecules, or ions to form a chemical compound.
There are three main types of chemical bonding that are ionic bonding, covalent bonding, and metallic bonding.
The chemical bonding within a molecule of carbon dioxide (CO2) different from the chemical bonding within a crystal of iron (Fe) because in a carbon dioxide molecule, atoms of carbon and oxygen are joined by sharing electrons. In an iron crystal, the atoms are held together by freely moving electrons.
Thus, option B is correct.
To learn more about the chemical bonding, follow the link;
https://brainly.com/question/12907148
#SPJ2
What is the velocity of a car that travels from mile marker 32 on I-10 to mile marker 312 on I-10 in a time of 2 hours and 45 minutes? SYW!
Answer:
101.81818 MPH
Explanation:
does the sabre-tooth currirulum still exist at present?give examples of your evidence
Answer: Should the sabre tooth curriculum really exist at the moment? As far as I am concerned, the sabre tooth program should remain, because our school system needs to help people know how to do complex activities on their own and we let them do activities that will help them develop their brains as well as their skills.
Great schools promote better teaching because they have the most experience of teaching practice and are accountable for executing the instruction in the classroom. Teacher engagement is also vital for the effective and substantive implementation of the curriculum.
Sources: files.eric.ed.gov and James Kennedy Monash
A 2 kg melon is balanced on your bald uncle’s head. His son, Throckmorton, shoots a 50 g (0.05kg) arrow at it with a speed of 30 m/s. The arrow passes through the melon and emerges with a speed of 18 m/s. Find the speed of the melon as it flies off the man’s head.
Answer:
The speed of the melon as it flies off the man’s head is 0.3 m/s.
Explanation:
Given;
mass of the melon, m₁ = 2 kg
initial speed of the melon, u₁ = 0
mass of arrow, m₂ = 0.05 kg
initial speed of the arrow, u₂ = 30 m/s
final speed of the arrow, v₂ = 18 m/s
let v₁ be the final speed of the melon as it flies off the man's head.
Apply the principle of conservation of linear momentum;
m₁u₁ + m₂u₂ = m₁v₁ + m₂v₂
2(0) + 0.05 x 30 = 2v₁ + 0.05 x 18
1.5 = 2v₁ + 0.9
2v₁ = 1.5 - 0.9
2v₁ = 0.6
v₁ = 0.6 / 2
v₁ = 0.3 m/s
Therefore, the speed of the melon as it flies off the man’s head is 0.3 m/s.
Part A Every force has one and only one 3rd law pair force. Every force has one and only one 3rd law pair force. true false Request Answer Part B The two forces in each pair act in opposite directions. The two forces in each pair act in opposite directions. true false Request Answer Part C The two forces in each pair can either both act on the same body or they can act on different bodies. The two forces in each pair can either both act on the same body or they can act on different bodies. true false
Answer:
Explanation:
Part A
Every force has one and only pair force , according to 3 rd law
It is true , the pair force has equal magnitude .
Part B
The two forces in each pair act in opposite directions.
It is true .
The pair forces are equal and act in opposite direction .
Part C
The two forces in each pair can either both act on the same body or they can act on different bodies.
It is false .
The two forces in each pair can not act on same body . They act on different bodies , bodies which are undergoing mutual interaction.
Consider the sections of two circuits illustrated above. Select True or False for all statements. After connecting c and d to a battery, the current through R3 always equals the current through R4. Rcd is always less than or equal to R3. After connecting a and b to a battery, the voltage across R1 always equals the voltage across R2. Rab is always less than or equal to R1.
Answer:
Follows are the solution to the given question:
Explanation:
In this question the missing file of the circuit is not be which is defined in attached file please find it.
In Option 1, this statement is true because the current is on [tex]R_3 \ and \ R_4[/tex], that is the same.
In option 2, this statement is false because [tex]Rcd=R_3+R_4[/tex] therefore it implies that Rcd is always larger then [tex]R_3[/tex].
In option 3, this statement is true because the voltage of [tex]R_1 \ and \ R_2[/tex] is always equal.
In option 4, this statement is true because [tex]Rab= \frac{1}{(\frac{1}{R1}+\frac{1}{R2})}=\frac{R1R2}{(R1+R2)}. \frac{R2}{(R1+R2)}[/tex]is always smaller then 1 therefore,[tex]R_1 \times (\frac{R2}{(R1+R2)})[/tex] is always equal to R1.
explain the principle of N-type semiconductor
Answer:
Explanation:
An N-type semiconductor is a type of material used in electronics. It is made by adding an impurity to a pure semiconductor such as silicon or germanium. The impurities used may be phosphorus, arsenic, antimony, bismuth or some other chemical element. They are called donor impurities
Select the correct answer.
A car is moving at a constant speed along a straight line. Which statement is true about the forces acting on the car?
ОА.
The net force acting on the car from all directions is zero.
o
B.
The net force acting on the car is greater than the car's weight.
O c.
The net force acting on the car is in the direction of the car's motion.
OD.
The net force acting on the car is in the opposite direction of the car's motion.
Answer:
ОА.
The net force acting on the car from all directions is zero.
Explanation:
Constant speed along a straight line
It means constant magnitude of velocity without chainging direction
It means constant velocity. Which means acclecration is zero
By Newton's second law:
[tex]F=ma[/tex]
Net force is also zero
A cylindrical pulley with a mass of 4.4 kg, radius of 0.816 m and moment of inertia 1 2 M r2 is used to lower a bucket with a mass of 3.1 kg into a well. The bucket starts from rest and falls for 2.9 s. r M m What is the linear acceleration of the falling bucket
Answer:
5.85 m/s²
Explanation:
Mass of pulley (M) = 6.8 kg, mass of bucket (m) = 1.5 kg, radius of pulley (r) = 0.816 m, acceleration due to gravity (g) = 10 m/s².
Let the tension exerted on the pulley be T and the angular acceleration be α,
The angular acceleration (α) = a / r; where a is the linear acceleration.
mg - T = ma
T = m(g - a)
Also, for the disk:
Tr = Iα
I = moment of inertia = 0.5Mr²
m(g - a)r = 0.5Mr²(a/r)
m(g - a)r = 0.5Mra
2m(g - a) = Ma
2mg - 2ma = Ma
Ma + 2ma = 2mg
a(M + 2m) = 2mg
a = 2mg / (M + 2m)
Substituting:
a = 2(3.1 kg)(10 m/s²) / (4.4 + 2(3.1))
a = 5.85 m/s²
A ball is Thrown Upward with An initial velocity of 30 m/s , How high does it rise from the ground when the ball reaches the highest Point ? And how long does it take to fall down to half of its height
Answer:
The maximum height reached by the ball is 45.92 mTime taken to fall down to half of its height is 2.2 sExplanation:
Given;
initial velocity of the ball, u = 30 m/s
final velocity of the ball at the highest point, v = 0
The maximum height reached by the ball is calculated as;
v² = u² - 2gh
where;
h is the maximum height reached by the ball
0 = 30² - (2 x 9.8)h
19.6h = 900
h = 900 / 19.6
h = 45.92 m
Time taken to fall to half of its height is calculated as;
when falling down, the final velocity v becomes the initial velocity = 0.
Apply the following kinematic equation;
h = ut + ¹/₂gt²
h = 0 + ¹/₂gt²
h = ¹/₂gt²
where;
h = 45.92 m is the maximum height reached
half of h = 45.92 / 2 = 22.96 m
22.96 = ¹/₂gt²
[tex]t = \sqrt{\frac{2h}{g} } \\\\t = \sqrt{\frac{2\times 22.96}{9.8} }\\\\t = 2.2 \ s[/tex]
a. Describe the big bang theory. (1 point) b. Match each model of the universe with the future it predicts. (1 point) A. Closed B. Flat C. Open _____ The universe will stop expanding but will not collapse. _____ The universe will continue to expand forever. _____ The universe will stop expanding and then collapse back to its point of origin. c. Match each observation to the conclusion it supports in the big bang theory. (1 point) A. Light from other galaxies is shifted toward the red end of the spectrum. B. Cosmic background radiation appears uniform across the sky. C. The amount of helium in the universe matches predictions. _____ Nucleosynthesis of light elements occurred shortly after the expansion of the original ball of energy. _____ The universe is expanding. _____ The universe began from a single point.
Answer:
A)
The Big Bang is the earliest known event in the observable Universe, its earliest known phase of evolution, and the name of the model for this process. According to this scenario, the Big Bang took place around 13.800 million years ago, when the known Universe emerged from very dense and hot matter. This theory is based on observations showing that space is expanding from an initial state where all the matter in the universe had a very high density and temperature, to a more cold and stable one.
B)
A. Closed. The universe will stop expanding and then collapse back to its point of origin.
B. Flat. The universe will stop expanding but will not collapse.
C. Open. The universe will continue to expand forever.
why all traveller prefer to travel easily in the morning and night and not when the sun is hot
Answer:
Travelers prefer to travel in morning because arthat time the temperature ️ is not too hot and they can easily travel here and there without any problem. and they also prefer to travel in night because moderate temperature ....
magnitude of the normal force exerted by en in the figure below. What is the
A suitcase of mass mis resting on an inclined plane
?
Answer:
B
Explanation:
Reason is that the suitcase is exerted downward and when it moves downward the equation is mgsin tita
A ball is thrown up into the air. The time that it takes to go up equals
Answer:
The time it takes the ball to rise equals the time it takes to fall.
Explanation:
because what goes up at some point must come down
A rock accelerated 4.8 m/s² as it was kicked with a force of 1.79 Newtons. What was the mass of the rock?
2.68 kg
0.37 kg
6.59 kg
3.01 kg
An uncharged capacitor and a resistor are connected in series with a switch and a 12 V battery. At the instant the switch is closed, the voltage across the resistor is
Answer:
V = 12 V
Explanation:
Since a capacitor can't change the voltage between its plates instantaneously, this means that just after the switch is closed, the voltage through the capacitor is zero.So, the current that flows in this moment is the same that would flow in a series circuit with only one resistor connected to the battery.Applying KVL to the circuit (neglecting the presence of the capacitor which can be replaced by a short circuit just after closing the switch), the voltage through the resistor must be equal to the one of the battery, i.e., 12 V.A glass optical fiber is used to transport a light ray across a long distance. The fiber has an index of refraction of 1.520 and is submerged in ethyl alcohol, which has an index of refraction of 1.361. What is the critical angle (in degrees) for the light ray to remain inside the fiber
Answer:
θ = 63.5º
Explanation:
When a ray of light strikes the separation surface between two transparent media with different index of refraction, part of the light remains in the first medium, and part transmits to the second one , according to the Snell's Law, as follows:[tex]sin \theta_{i}* n_{i} = sin \theta_{r}* n_{r} (1)[/tex]
where θi = angle of incidence (with the normal to the surface)
θr = angle of refraction (with the normal to the surface)
ni = index of refraction of denser medium = 1.520
nr = index of refraction of less dense medium = 1.361
When the angle of refraction is equal to a right angle, this means that the light is parallel to the surface, and remains within the first medium completely.The angle of incidence for this particular angle, is called the limit angle, and is the principle of operation of fiber optics, which are composed by a strand of glass, surrounded with another material, which index of refraction is lower than the fiber's, preventing light to go outside the fiber.In our case, replacing ni, nr, and θr = 90º in (1), we get:[tex]sin \theta_{i}* 1.520 = 1* 1.361 (2)[/tex]Solving for sin θ₁ :[tex]sin \theta_{i} = \frac{1.361}{1.520} = 0.895 (3)[/tex]
⇒ θi = sin⁻¹ (0.895) = 63.5º
why is a simple cell importable
A battery connected to two wires in parallel. Both wires are made of the same material and are of the same length, but the diameter of wire A is twice the diameter of wire B.
True or False for the following:
1) The resistance of wire B is four times as large as the resistance of wire A.
2) The power dissipated in wire A is 16 times the power dissipated in wire B.
3) The voltage drop across wire B is larger than the voltage drop across wire A.
4) The resistance of wire B is twice as large as the resistance of wire A.
5) The current through the battery is five times larger than the current through wire B.
Answer:
true 1
2 is false 2. 3 . 4. 5
Explanation:
For this exercise, let's calculate the different parameters and analyze the corresponding statements.
the resistance of each wire
R = ρ [tex]\frac{L}{A}[/tex]
wire B.
has a diameter of d₀
therefore its radius is r₀ = d₀ / 2
the area is A = pi r₀²
A = π d₀²/ 4
we subtitle
Ro = ρ [tex]\frac{L \ 4}{\pi d_o^2}[/tex]
R_b = R₀
wire A
the diameter is d = 2d₀
therefore the radius is r = d/2
r = d₀
resistance is
R_a = ρ [tex]\frac{L}{\pi d_o}[/tex]
R_a = 4 R₀
when examining the answers
1 is true
4 is false
Now let's calculate the power
P = V I
V = I R
P = V² / R
as they indicate that the cables are connected in parallel, the voltage in them is the same, therefore the potency depends on the resistance
wire B
P = V² / R_b
P_b = V² / R₀
wire A
P_a = v² / R_a
P_a = V² / 4R₀
P_a = ¼ P_b
2 is false
in a parallel circuit the waves are the same therefore
3 False
ohm's law is
V = I r
I = V / R
wire B
I_b = V / R_b
I_b = V / Ro
wire
I_a = V / R_a
I_a = V / 4 Ro
I_a = ¼ I_a
5 is false
You are traveling on a plane trip from Washington, D.C. to Cleveland, Ohio and the plane uses 1,260 MJ/passenger trip. If you made the trip by car it would take 18 gallons/passenger trip. There are 142 MJ in a gallon of kerosene, a type of jet fuel. How many gallons of kerosene does it take to make the trip by plane?
Answer:
8.87 gallons of kerosene
Explanation:
Step 1: Given and required data
Energy to travel by plane per passenger trip: 1,260 MJ/passenger tripEnergy per gallon of kerosene: 142 MJ/galStep 2: Calculate how many gallons of kerosene it takes to make the trip by plane
We can calculate the amount of kerosene required by combining the factor provided in Step 1.
1 gal/142 MJ × 1,260 MJ/passenger trip = 8.87 gal/passenger trip
8.87 gallons of kerosene are required to make the trip by plane.
what is the combination of two or more simple machine
Answer:
compound machineExplanation:
A compound machine is a combination of two or more simple machines.
BRAINLIEST? plz
The blocks are forced together, compressing a spring between them by a distance x; (the force constant of the spring is k) then the system is released from rest on a level, frictionless surface. The spring, which has negligible mass, is not fastened to either block and drops to the surface after it has expanded. What is the speed that block A acquired, vA
Answer:
v =[tex]\sqrt{\frac{k}{m} }[/tex] x
Explanation:
For this exercise let's use the important topic of conservation of energy
starting point. Spring compression point
Em₀ = K_e = ½ k x²
final point. When the spring is not compressed
Em_f = K = ½ m v²
as they indicate that there is no friction, the energy is conserved
Em₀ = Em_f
½ k x² = ½ m v²
v =[tex]\sqrt{\frac{k}{m} }[/tex] x
A hamster eats a carrot before using its hamster wheel. The hamster wheel is connected to a generator which powers a light bulb.
Mechanical → Chemical → Radiant → Electrical
Chemical → Mechanical → Electrical → Radiant
Chemical → Mechanical → Thermal → Electrical
Mechanical → Electrical → Thermal → Radiant
Answer: Chemical → Mechanical → Electrical → Radiant
Explanation:
First, the Hamster eats the carrot, then the hamster is getting chemical energy.
Now the hamster starts using his wheel, then he "transforms" the chemical energy into mechanical energy.
Now the mechanical energy is connected to a generator, this means that the mechanical energy (the rotation of the wheel) is being converted into electrical energy.
And we know that there is a light bulb powered by this electrical energy, then we have electrical energy being transformed into radiant energy.
Then the correct option is:
Chemical → Mechanical → Electrical → Radiant
10/12
11.
You drive the 10 miles to the mall at an average speed of 40 mph. On
the way home, you hit severe traffic and had to drive at an average
speed of 10 mph. What is your average speed for the trip?
HELP PLZ
If an object has a mass of 1.5 KG what is the force of gravity on it?
Which choice describes a concern with wind energy?
O may harm bird and bat populations
o negative impact on river ecosystems
O turbines are cheaply made
O could interfere with pollen distribution
A concern which is related to the wind energy is that these could interfere with the pollen distribution. Thus, the correct option is D.
What is Wind energy?Wind power or wind energy is mostly used in the wind turbines to generate electricity. The wind power is a popular, sustainable, renewable energy source which has a much smaller impact on the surrounding environment than that of burning fossil fuels.
Some disadvantages of wind energy include noise and visual pollution, wind power is not a remote power, and the effects or impact on the environment including interference with the pollen distribution.
Therefore, the correct option is D.
Learn more about Wind energy here:
https://brainly.com/question/29293441
#SPJ6
What causes an electromagnet to create a magnetic field?
A.The Earth's magnetic field.
B.The poles are attracted to each other.
C.The iron is wrapped with a coiled wire.
D.There is a current flowing through the wire.
Answer:
D
Explanation:
Have a great day ;)