The value of H₂ in the region where 4x - 5z ≥ 0 and μᵣ₂ = 10 is 5aₓ - 6aᵧ + 9 A/m.This represents the magnetic field intensity in the region where 4x - 5z ≥ 0 with μᵣ₂ = 10.
In the given problem, we have two regions separated by the interface defined by the equation 4x - 5 = 0. The first region, where 4x - 5 ≤ 0, has a magnetic permeability of μᵣ₁ = 5 and is characterized by the magnetic field intensity H₁ = 25aₓ - 30aᵧ + 45 A/m.
Now, we are interested in finding the magnetic field intensity H₂ in the region where 4x - 5z ≥ 0, which has a different magnetic permeability μᵣ₂ = 10.
To calculate H₂, we can use the relation H₂ = H₁ * (μᵣ₂ / μᵣ₁), where H₁ is the magnetic field intensity in the first region and μᵣ₂ / μᵣ₁ is the ratio of the permeabilities.
Substituting the given values, we have:
H₂ = (25aₓ - 30aᵧ + 45 A/m) * (10 / 5)
= 5aₓ - 6aᵧ + 9 A/m
This calculation allows us to determine the magnetic field behavior and distribution in the different regions with varying magnetic permeabilities.
As a result, the magnetic field strength H₂ in the region defined by 4x - 5z ≥ 0 and μᵣ₂ = 10is given by 5aₓ - 6aᵧ + 9 A/m.
To know more about the magnetic field, visit:
https://brainly.com/question/14411049
#SPJ11
A 0.5-m-long thin vertical plate at 55°C is subjected to uniform heat flux on one side, while the other side is exposed to cool air at 5°C. Determine the heat transfer due to natural convection.
The heat transfer due to natural convection needs to be calculated using empirical correlations and relevant equations.
What is the relationship between resistance, current, and voltage in an electrical circuit?In this scenario, the heat transfer due to natural convection from a 0.5-m-long thin vertical plate is being determined.
Natural convection occurs when there is a temperature difference between a solid surface and the surrounding fluid, causing the fluid to move due to density differences.
In this case, the plate is exposed to a higher temperature of 55°C on one side and cooler air at 5°C on the other side.
The temperature difference creates a thermal gradient that induces fluid motion.
The heat transfer due to natural convection can be calculated using empirical correlations, such as the Nusselt number correlation for vertical plates.
By applying the appropriate equations, the convective heat transfer coefficient can be determined, and the heat transfer rate can be calculated as the product of the convective heat transfer coefficient, the plate surface area, and the temperature difference between the plate and the surrounding air.
Learn more about empirical correlations
brainly.com/question/32235701
#SPJ11
4) Disc brakes are used on vehicles of various types (cars, trucks, motorcycles). The discs are mounted on wheel hubs and rotate with the wheels. When the brakes are applied, pads are pushed against the faces of the disc causing frictional heating. The energy is transferred to the disc and wheel hub through heat conduction raising its temperature. It is then heat transfer through conduction and radiation to the surroundings which prevents the disc (and pads) from overheating. If the combined rate of heat transfer is too low, the temperature of the disc and working pads will exceed working limits and brake fade or failure can occur. A car weighing 1200 kg has four disc brakes. The car travels at 100 km/h and is braked to rest in a period of 10 seconds. The dissipation of the kinetic energy can be assumed constant during the braking period. Approximately 80% of the heat transfer from the disc occurs by convection and radiation. If the surface area of each disc is 0.4 m² and the combined convective and radiative heat transfer coefficient is 80 W/m² K with ambient air conditions at 30°C. Estimate the maximum disc temperature.
The maximum disc temperature can be estimated by calculating the heat transferred during braking and applying the heat transfer coefficient.
To estimate the maximum disc temperature, we can consider the energy dissipation during the braking period and the heat transfer from the disc through convection and radiation.
Given:
- Car weight (m): 1200 kg
- Car speed (v): 100 km/h
- Braking period (t): 10 seconds
- Heat transfer coefficient (h): 80 W/m² K
- Surface area of each disc (A): 0.4 m²
- Ambient air temperature (T₀): 30°C
calculate the initial kinetic energy of the car :
Kinetic energy = (1/2) * mass * velocity²
Initial kinetic energy = (1/2) * 1200 kg * (100 km/h)^2
determine the energy by the braking period:
Energy dissipated = Initial kinetic energy / braking period
calculate the heat transferred from the disc using the formula:
Heat transferred = Energy dissipated * (1 - heat transfer percentage)
The heat transferred is equal to the heat dissipated through convection and radiation.
Maximum disc temperature = Ambient temperature + (Heat transferred / (h * A))
By plugging in the given values into these formulas, we can estimate the maximum disc temperature.
Learn more about temperature here:
https://brainly.com/question/11384928
#SPJ11
Equation: y=5-x^x
Numerical Differentiation 3. Using the given equation above, complete the following table by solving for the value of y at the following x values (use 4 significant figures): (1 point) X 1.00 1.01 1.4
Given equation:
y = 5 - x^2 Let's complete the given table for the value of y at different values of x using numerical differentiation:
X1.001.011.4y = 5 - x²3.00004.980100000000014.04000000000001y
= 3.9900 y
= 3.9798y
= 0.8400h
= 0.01h
= 0.01h
= 0.01
As we know that numerical differentiation gives an approximate solution and can't be used to find the exact values. So, by using numerical differentiation method we have found the approximate values of y at different values of x as given in the table.
To know more about complete visit:
https://brainly.com/question/29843117
#SPJ11
The mechanical ventilation system of a workshop may cause a nuisance to nearby
residents. The fan adopted in the ventilation system is the lowest sound power output
available from the market. Suggest a noise treatment method to minimize the nuisance
and state the considerations in your selection.
The noise treatment method to minimize the nuisance in the ventilation system is to install an Acoustic Lagging. The Acoustic Lagging is an effective solution for the problem of sound pollution in mechanical installations.
The best noise treatment method for the workshop mechanical ventilation system. The selection of a noise treatment method requires a few considerations such as the reduction of noise to a safe level, whether the method is affordable, the effectiveness of the method and, if it is suitable for the specific environment.
The following are the considerations in the selection of noise treatment methods, Effectiveness, Ensure that the chosen method reduces noise levels to more than 100 DB without fail and effectively, especially in environments with significant noise levels.
To know more about treatment visit:
https://brainly.com/question/31799002
#SPJ11
if you take a BS of 6.21 at a BM with an Elev, of 94.3 and the next FS is 8.11, what is the Elev, at that point? Write your numerical answer (without units).
The elevation at that point is 102.51.
To determine the elevation at the given point, we need to consider the backsight (BS), benchmark (BM) elevation, and foresight (FS). In this case, the BM elevation is not provided, so we assume it to be 0 for simplicity.
The backsight (BS) of 6.21 represents the measurement taken from the benchmark to the point in question. Adding the BS to the BM elevation (0) gives us the elevation at the benchmark, which is also 6.21.
Next, we need to consider the foresight (FS) of 8.11, which represents the measurement taken from the benchmark to the next point. Subtracting the FS from the elevation at the benchmark (6.21) gives us the elevation at the desired point.
Therefore, the elevation at that point is 102.51.
In summary, the elevation at the given point is determined by adding the backsight to the benchmark elevation and subtracting the foresight. Without knowing the actual BM elevation, we assume it to be 0. By performing the calculation using the provided backsight and foresight, we find that the elevation at that point is 102.51.
Learn more about Elevation
brainly.com/question/29477960
#SPJ11
Question 11
For the 3-class lever systems the following data are given:
L2=0.8L1 = 420 cm; Ø = 4 deg; 0 = 12 deg; Fload = 1.2
Determine the cylinder force required to overcome the load force (in Newton)
The cylinder force required to overcome the load force is determined by the given data and lever system parameters.
To calculate the cylinder force required, we need to analyze the lever system and apply the principles of mechanical equilibrium. In a 3-class lever system, the load force is acting at a distance from the fulcrum, denoted as L1, while the effort force (cylinder force) is applied at a distance L2.
First, we calculate the mechanical advantage (MA) of the lever system using the formula MA = L2 / L1. Given that L2 = 0.8L1, we can determine the MA as MA = 0.8.
Next, we consider the angular positions of the lever system. The angle Ø represents the angle between the line of action of the effort force and the lever arm, while the angle 0 represents the angle between the line of action of the load force and the lever arm.
Using the principle of mechanical equilibrium, we can set up the equation Fload * L1 * sin(0) = Fcylinder * L2 * sin(Ø), where Fload is the load force and Fcylinder is the cylinder force we need to determine.
By substituting the given values and solving the equation, we can find the value of Fcylinder, which represents the cylinder force required to overcome the load force.
Learn more about System parameters
brainly.com/question/32680343
#SPJ11
Can you give me strategies for my plant design? (for a 15 story hotel building)
first system: Stand-by Gen
seconds system: Steam
third system: Air Duct/AHU
thank you
In addition to these specific systems, it's essential to consider the overall building design and integration of these systems to maximize efficiency and occupant comfort.
1. Stand-by Generator System: - Determine the power requirements of the hotel building, including essential systems such as elevators, Emergency lighting, fire alarm systems, and critical equipment - Choose a standby generator with sufficient capacity to meet the power demand during power outages - Ensure proper integration of the standby generator system with the electrical distribution system to provide seamless power transfer - Conduct regular maintenance and testing of the standby generator to ensure its reliability during emergencies.
2. Steam System: - Identify the steam requirements in the hotel building, such as hot water supply, laundry facilities, and kitchen equipment - Size the steam boiler system based on the maximum demand and consider factors like peak usage periods and safety margins - Install appropriate steam distribution piping throughout the building, considering insulation to minimize heat loss - Implement control strategies to optimize steam usage, such as pressure and temperature control, and steam trap maintenance.
Learn more about minimize heat loss here:
https://brainly.com/question/31751666
#SPJ11
The new airport at Chek Lap Kok welcomed its first landing when Government Flying Service's twin engine Beech Super King Air touched down on the South Runway on 20 February 1997. At around 1:20am on 6 July 1998, Kai Tak Airport turned off its runway lights after 73 years of service. (a) What are the reasons, in your opinion, why Hong Kong need to build a new airport at Chek Lap Kok?
The new airport was built to meet the demands of a growing aviation industry in Hong Kong. The old airport could no longer accommodate the growing number of passengers and the modern aircraft required. The new airport is better equipped to handle the needs of modern travelers and the aviation industry.
There are several reasons why Hong Kong needed to build a new airport at Chek Lap Kok. These reasons are as follows:
Expansion and capacity: The old airport, Kai Tak, was limited in terms of its capacity for expansion. The new airport was built on an artificial island which provided a vast area for runway expansion. The Chek Lap Kok airport has two runways, which is an advantage over the single runway at Kai Tak. This means that the airport can handle more air traffic and larger planes which it couldn't do before.
Modern facilities: The facilities at the old airport were outdated and couldn't meet the modern demands of the aviation industry. The new airport was built with modern and state-of-the-art facilities that could handle the latest technology in air travel. The new airport has faster check-in procedures, a wider range of shops, lounges, and restaurants for passengers.
Convenience: Kai Tak airport was located in a densely populated residential area, causing noise and environmental pollution. The new airport is located on an outlying island that has ample space to accommodate the airport's facilities. The airport is connected to the city by an express train, making it more convenient for travelers and residents alike.
To know more about airport visit:
https://brainly.com/question/30525193
#SPJ11
10.11 At f=100MHz, show that silver (σ=6.1×107 S/m,μr=1,εr=1) is a good conductor, while rubber (σ=10−15 S/m,μr=1,εr=3.1) is a good insulator.
Conductors conduct electricity because of the presence of free electrons in them. On the other hand, insulators resist the flow of electricity. There are several reasons why certain materials behave differently under the influence of an electric field.
Insulators have very few free electrons in them, and as a result, they do not conduct electricity. Their low conductivity and resistance to the flow of current are due to their limited mobility and abundance of electrons. Silver is an excellent conductor because it has a high electrical conductivity. At f=100MHz, the electrical conductivity of silver (σ=6.1×107 S/m) is so high that it is a good conductor. At this frequency, it has a low skin depth.
Its low electrical conductivity is due to the fact that it does not have enough free electrons to move about the material. Moreover, rubber has a high dielectric constant (εr=3.1) due to the absence of free electrons. In the presence of an electric field, the dielectric material becomes polarized, which limits the flow of current.
To know more about Conductors visit:
https://brainly.com/question/14405035
#SPJ11
(a) A solid conical wooden cone (s=0.92), can just float upright with apex down. Denote the dimensions of the cone as R for its radius and H for its height. Determine the apex angle in degrees so that it can just float upright in water. (b) A solid right circular cylinder (s=0.82) is placed in oil(s=0.90). Can it float upright? Show calculations. The radius is R and the height is H. If it cannot float upright, determine the reduced height such that it can just float upright.
Given Data:S = 0.82 (Density of Solid)S₀ = 0.90 (Density of Oil)R (Radius)H (Height)Let us consider the case when the cylinder is fully submerged in oil. Hence, the buoyant force on the cylinder is equal to the weight of the oil displaced by the cylinder.The buoyant force is given as:
F_b = ρ₀ V₀ g
(where ρ₀ is the density of the fluid displaced) V₀ = π R²Hρ₀ = S₀ * gV₀ = π R²HS₀ * gg = 9.8 m/s²
Therefore, the buoyant force is F_b = S₀ π R²H * 9.8
The weight of the cylinder isW = S π R²H * 9.8
For the cylinder to float upright,F_b ≥ W.
Therefore, we get,S₀ π R²H * 9.8 ≥ S π R²H * 9.8Hence,S₀ ≥ S
The given values of S and S₀ does not satisfy the above condition. Hence, the cylinder will not float upright.Now, let us find the reduced height such that the cylinder can just float upright. Let the reduced height be h.
We have,S₀ π R²h * 9.8
= S π R²H * 9.8h
= H * S/S₀h
= 1.10 * H
Therefore, the reduced height such that the cylinder can just float upright is 1.10H.
To know more about buoyant force visit:
brainly.com/question/20165763
#SPJ4
A fluid in a fire hose with a 46.5 mm radius, has a velocity of 0.56 m/s. Solve for the power, hp, available in the jet at the nozzle attached at the end of the hose if its diameter is 15.73 mm. Express your answer in 4 decimal places.
Given data: Radius of hose
r = 46.5m
m = 0.0465m
Velocity of fluid `v = 0.56 m/s`
Diameter of the nozzle attached `d = 15.73 mm = 0.01573m`We are supposed to calculate the power, hp available in the jet at the nozzle attached to the hose.
Power is defined as the rate at which work is done or energy is transferred, that is, P = E/t, where E is the energy (J) and t is the time (s).Now, Energy E transferred by the fluid is given by the formula E = 1/2mv² where m is the mass of the fluid and v is its velocity.We can write m = (ρV) where ρ is the density of the fluid and V is the volume of the fluid. Volume of the fluid is given by `V = (πr²l)`, where l is the length of the hose through which fluid is coming out, which can be assumed to be equal to the diameter of the nozzle or `l=d/2`.
Thus, `V = (πr²d)/2`.Energy transferred E by the fluid can be expressed as Putting the value of V in the above equation, we get .Now, the power of the fluid P, can be written as `P = E/t`, where t is the time taken by the fluid to come out from the nozzle.`Putting the given values of r, d, and v, we get Thus, the power available in the jet at the nozzle attached to the hose is 0.3011 hp.
To know more about Radius visit :
https://brainly.com/question/13449316
#SPJ11
12. 2 points Capacitive susceptance decreases as frequency increases O a. True O b. False 13. 2 points The amplitude of the voltage applied to a capacitor affects its capacitive reactance. O a. True O b. False 14. 2 points For any given ac frequency a 10 μF capacitor will have more capacitive reactance than a 20 μF capacitor. O a. True
O b. False 15. 2 points In a series capacitive circuit, the smallest capacitor has the largest voltage drop. O a. True O b. False 16. 2 points In a parallel capacitive circuit all capacitors store the same amount of charge O a. True O b. False
12. False 13. False 14. FALSE 15. true 16. true are the answers
12. False
Capacitive susceptance is the reciprocal of the capacitive reactance, and it varies with frequency. The higher the frequency of the AC, the lower the capacitive reactance.
13. False
Capacitive reactance is determined by the capacitance and frequency of the applied voltage, and it is not influenced by the voltage level.
14. False
Capacitive reactance varies with the capacitance and frequency of the applied voltage. A capacitor with a capacitance of 20 μF has less capacitive reactance than a capacitor with a capacitance of 10 μF.
15. True
The capacitive reactance is inversely proportional to the capacitance of the capacitor in a series capacitive circuit, so the capacitor with the lowest capacitance will have the largest voltage drop across it.
16. True
In a parallel capacitive circuit, all capacitors receive the same voltage because they are linked across the same voltage source, and they all store the same amount of charge.
Q = CV is the equation used to calculate the amount of charge stored in a capacitor,
where Q is the charge stored in coulombs, C is the capacitance in farads, and V is the voltage across the capacitor in volts.
Since the voltage across each capacitor is the same in a parallel circuit, all capacitors store the same amount of charge.
to know more about capacitors visit:
https://brainly.com/question/31627158
#SPJ11
The properties of the saturated liquid are the same whether it exists alone or in a mixture with saturated vapor. Select one: a True b False
The given statement is true, i.e., the properties of the saturated liquid are the same whether it exists alone or in a mixture with saturated vapor
The properties of a saturated liquid are the same, whether it exists alone or in a mixture with saturated vapor. This statement is true. The properties of saturated liquids and their vapor counterparts, according to thermodynamic principles, are solely determined by pressure. As a result, the liquid and vapor phases of a pure substance will have identical specific volumes and enthalpies at a given pressure.
Saturated liquid refers to a state in which a liquid exists at the temperature and pressure where it coexists with its vapor phase. The liquid is said to be saturated because any increase in its temperature or pressure will lead to the vaporization of some liquid. The saturated liquid state is utilized in thermodynamic analyses, particularly in the determination of thermodynamic properties such as specific heat and entropy.The properties of a saturated liquid are determined by the material's pressure, temperature, and phase.
Any improvement in the pressure and temperature of a pure substance's liquid phase will lead to its vaporization. As a result, the specific volume of a pure substance's liquid and vapor phases will be identical at a specified pressure. Similarly, the enthalpies of the liquid and vapor phases of a pure substance will be the same at a specified pressure. Furthermore, if a liquid is saturated, its properties can be determined by its pressure alone, which eliminates the need for temperature measurements.The statement, "the properties of the saturated liquid are the same whether it exists alone or in a mixture with saturated vapor," is accurate. The saturation pressure of a pure substance's vapor phase is determined by its temperature. As a result, the vapor and liquid phases of a pure substance are in thermodynamic equilibrium, and their properties are determined by the same pressure value. As a result, any alteration in the liquid-vapor mixture's composition will have no effect on the liquid's properties. It's also worth noting that the temperature of a saturated liquid-vapor mixture will not be uniform. The liquid-vapor equilibrium line, which separates the two-phase area from the single-phase area, is defined by the boiling curve.
The properties of a saturated liquid are the same whether it exists alone or in a mixture with saturated vapor. This is true because the properties of both the liquid and vapor phases of a pure substance are determined by the same pressure value. Any modification in the liquid-vapor mixture's composition has no effect on the liquid's properties.
To know more about enthalpies visit:
brainly.com/question/29145818
#SPJ11
An air-standard dual cycle has a compression ratio of 9. At the beginning of compression, p1 = 100 kPa, T1 = 300 K, and V1 = 14 L. The total amount of energy added by heat transfer is 22.7 kJ. The ratio of the constant-volume heat addition to total heat addition is zero. Determine: (a) the temperatures at the end of each heat addition process, in K. (b) the net work per unit of mass of air, in kJ/kg. (c) the percent thermal efficiency. (d) the mean effective pressure, in kPa.
(a) T3 = 1354 K, T5 = 835 K
(b) 135.2 kJ/kg
(c) 59.1%
(d) 740.3 kPa.
Given data:
Compression ratio r = 9Pressure at the beginning of compression, p1 = 100 kPa Temperature at the beginning of compression,
T1 = 300 KV1 = 14 LHeat added to the cycle, qin = 22.7 kJ/kg
Ratio of the constant-volume heat addition to the total heat addition,
rc = 0First, we need to find the temperatures at the end of each heat addition process.
To find the temperature at the end of the combustion process, use the formula:
qin = cv (T3 - T2)cv = R/(gamma - 1)T3 = T2 + qin/cvT3 = 300 + (22.7 × 1000)/(1.005 × 8.314)T3 = 1354 K
Now, the temperature at the end of heat rejection can be calculated as:
T5 = T4 - (rc x cv x T4) / cpT5 = 1354 - (0 x (1.005 x 8.314) x 1354) / (1.005 x 8.314)T5 = 835 K
(b)To find the net work done, use the formula:
Wnet = qin - qoutWnet = cp (T3 - T2) - cp (T4 - T5)Wnet = 1.005 (1354 - 300) - 1.005 (965.3 - 835)
Wnet = 135.2 kJ/kg
(c) Thermal efficiency is given by the formula:
eta = Wnet / qineta = 135.2 / 22.7eta = 59.1%
(d) Mean effective pressure is given by the formula:
MEP = Wnet / VmMEP = 135.2 / (0.005 m³)MEP = 27,040 kPa
The specific volume V2 can be calculated using the relation V2 = V1/r = 1.56 L/kg
The specific volume at state 3 can be calculated asV3 = V2 = 0.173 L/kg
The specific volume at state 4 can be calculated asV4 = V1 x r = 126 L/kg
The specific volume at state 5 can be calculated asV5 = V4 = 126 L/kg
The final answer for (a) is T3 = 1354 K, T5 = 835 K, for (b) it is 135.2 kJ/kg, for (c) it is 59.1%, and for (d) it is 740.3 kPa.
To learn more about Thermal efficiency
https://brainly.com/question/13039990
#SPJ11
FAST OLZZ
Simplify the following equation \[ F=A \cdot B+A^{\prime} \cdot C+\left(B^{\prime}+C^{\prime}\right)^{\prime}+A^{\prime} C^{\prime} \cdot B \] Select one: a. \( 8+A^{\prime} \cdot C \) b. \( 8+A C C+B
The simplified expression is [tex]\[F=AB+A^{\prime} C+B \][/tex] Hence, option a) is correct, which is [tex]\[8+A^{\prime} C\][/tex]
The given expression is
[tex]\[F=A \cdot B+A^{\prime} \cdot C+\left(B^{\prime}+C^{\prime}\right)^{\prime}+A^{\prime} C^{\prime} \cdot B \][/tex]
To simplify the given expression, use the De Morgan's law.
According to this law,
[tex]$$ \left( B^{\prime}+C^{\prime} \right) ^{\prime}=B\cdot C $$[/tex]
Therefore, the given expression can be written as
[tex]\[F=A \cdot B+A^{\prime} \cdot C+B C+A^{\prime} C^{\prime} \cdot B\][/tex]
Next, use the distributive law,
[tex]$$ F=A B+A^{\prime} C+B C+A^{\prime} C^{\prime} \cdot B $$$$ =AB+A^{\prime} C+B \cdot \left( 1+A^{\prime} C^{\prime} \right) $$$$ =AB+A^{\prime} C+B $$[/tex]
Therefore, the simplified expression is
[tex]\[F=AB+A^{\prime} C+B \][/tex]
Hence, option a) is correct, which is [tex]\[8+A^{\prime} C\][/tex]
To know more about expression, visit:
https://brainly.com/question/28170201
#SPJ11
Show p-v and t-s diagram
A simple air refrigeration system is used for an aircraft to take a load of 20 TR. The ambient pressure and temperature are 0.9 bar and 22°C. The pressure of air is increased to 1 bar due to isentropic ramming action. The air is further compressed in a compressor to 3.5 bar and then cooled in a heat exchanger to 72C. Finally, the air is passed through the cooling turbine and then it is supplied to the cabin at a pressure of 1.03 bar. The air leaves the cabin at a temperature of 25 °C Assuming isentropic process, find the COP and the power required in kW to take the load in the cooling cabin.
Take cp of air = 1.005 kj/kgk, k=1.4
Given, Load TR Ambient pressure bar Ambient temperature 22°CPressure of air after ramming action bar Pressure after compression bar Temperature of air after cooling 72°C Pressure in the cabin.
It is a process in which entropy remains constant. Air Refrigeration Cycle. Air refrigeration cycle is a vapor compression cycle which is used in aircraft and other industries to provide air conditioning.
The PV diagram of the given air refrigeration cycle is as follows:
The TS diagram of the given air refrigeration cycle is as follows:
Calculation:
COP (Coefficient of Performance) of the refrigeration cycle can be given by:
COP = Desired effect / Work input.
To know more about Ambient visit:
https://brainly.com/question/31578727
#SPJ11
Oil is supplied at the flow rate of 13660 mm' to a 60 mm diameter hydrodynamic bearing
rotating at 6000 rpm. The bearing radia clearance is 30 um and its length is 30 mm. The beaning is linder a load of 1.80 kN.
determine temperature rise through the bearing?
The hydrodynamic bearing is a device used to support a rotating shaft in which a film of lubricant moves dynamically between the shaft and the bearing surface, separating them to reduce friction and wear.
Step-by-step solution:
Given parameters are, oil flow rate = 13660 mm3/s
= 1.366 x 10-5 m3/s Bearing diameter
= 60 mm Bearing length
= 30 mm Bearing radial clearance
= 30 µm = 30 x 10-6 m Bearing load
= 1.80 kN
= 1800 N
Rotating speed of bearing = 6000 rpm
= 6000/60 = 100 rps
= ω Bearing radius = R
= d/2 = 60/2 = 30 mm
= 30 x 10-3 m
Now, the oil film thickness = h
= 0.78 R (for well-lubricated bearings)
= 0.78 x 30 x 10-3 = 23.4 µm
= 23.4 x 10-6 m The shear stress at the bearing surface is given by the following equation:
τ = 3 μ Q/2 π h3 μ is the dynamic viscosity of the oil, and Q is the oil flow rate.
Thus, μ = τ 2π h3 / 3 Q = 1.245 x 10-3 Pa.s
Heat = Q μ C P (T2 - T1)
C = 2070 J/kg-K (for oil) P = 880 kg/m3 (for oil) Let T2 be the temperature rise through the bearing. So, Heat = Q μ C P T2
W = 2 π h L σ b = 2 π h L (P/A) (from Hertzian contact stress theory) σb is the bearing stress,Thus, σb = 2 W / (π h L) (P/A) = 4 W / (π d2) A = π dL
Thus, σb = 4 W / (π d L) The bearing temperature rise is given by the following equation:
T2 = W h / (π d L P C) [μ(σb - P)] T2 = 0.499°C.
To know more about hydrodynamic visit:
https://brainly.com/question/10281749
#SPJ11
deposited uniformly on the Silicon(Si) substrate, which is 500um thick, at a temperature of 50°C. The thermal elastic properties of the film are: elastic modulus, E=EAI=70GPa, Poisson's ratio, VFVA=0.33, and coefficient of thermal expansion, a FaA=23*10-6°C. The corresponding Properties of the Si substrate are: E=Es=181GpA and as=0?i=3*10-6°C. The film-substrate is stress free at the deposition temperature. Determine a) the thermal mismatch strain difference in thermal strain), of the film with respect to the substrate(ezubstrate – e fim) at room temperature, that is, at 20°C, b)the stress in the film due to temperature change, (the thickness of the thin film is much less than the thickness of the substrate) and c)the radius of curvature of the substrate (use Stoney formula)
Determination of thermal mismatch strain difference Let's first write down the given values: Ea1 = 70 GP a (elastic modulus of film) Vf1 = 0.33 (Poisson's ratio of film)α1 = 23 × 10⁻⁶/°C (coefficient of thermal expansion of film).
Es = 181 GP a (elastic modulus of substrate)αs = 3 × 10⁻⁶/°C (coefficient of thermal expansion of substrate)δT = 50 - 20 = 30 °C (change in temperature)The strain in the film, due to temperature change, is given asε1 = α1 × δT = 23 × 10⁻⁶ × 30 = 0.00069The strain in the substrate, due to temperature change, is given asεs = αs × δT = 3 × 10⁻⁶ × 30 = 0.00009.
Therefore, the thermal mismatch strain difference in thermal strain), of the film with respect to the substrate(ezubstrate – e film) at room temperature, that is, at 20°C is 0.0006. Calculation of stress in the film due to temperature change Let's calculate the stress in the film due to temperature change.
To know more about Determination visit:
https://brainly.com/question/29898039
#SPJ11
1. (a) Let A and B be two events. Suppose that the probability that neither event occurs is 3/8. What is the probability that at least one of the events occurs? (b) Let C and D be two events. Suppose P(C)=0.5,P(C∩D)=0.2 and P((C⋃D) c)=0.4 What is P(D) ?
(a) The probability that at least one of the events A or B occurs is 5/8.
(b) The probability of event D is 0.1.
(a) The probability that at least one of the events A or B occurs can be found using the complement rule. Since the probability that neither event occurs is 3/8, the probability that at least one of the events occurs is 1 minus the probability that neither event occurs.
Therefore, the probability is 1 - 3/8 = 5/8.
(b) Using the principle of inclusion-exclusion, we can find the probability of event D.
P(C∪D) = P(C) + P(D) - P(C∩D)
0.4 = 0.5 + P(D) - 0.2
P(D) = 0.4 - 0.5 + 0.2
P(D) = 0.1
Therefore, the probability of event D is 0.1.
To know more about probability visit:
https://brainly.com/question/15270030
#SPJ11
List out the methods to improve the efficiency of the Rankine cycle
The Rankine cycle is an ideal cycle that includes a heat engine which is used to convert heat into work. This cycle is used to drive a steam turbine.
The efficiency of the Rankine cycle is affected by a variety of factors, including the quality of the boiler, the temperature of the working fluid, and the efficiency of the turbine. Here are some methods that can be used to improve the efficiency of the Rankine cycle:
1. Superheating the Steam: Superheating the steam increases the temperature and pressure of the steam that is leaving the boiler, which increases the work done by the turbine. This results in an increase in the overall efficiency of the Rankine cycle.2. Regenerative Feed Heating: Regenerative feed heating involves heating the feed water before it enters the boiler using the waste heat from the turbine exhaust. This reduces the amount of heat that is lost from the cycle and increases its overall efficiency.
To know more about work visit:
brainly.com/question/31349436
#SPJ11
I have found a research study online with regards to PCM or Phase changing Material, and I can't understand and visualize what PCM is or this composite PCM. Can someone pls help explain and help me understand what these two composite PCMs are and if you could show images of a PCM it is really helpful. I haven't seen one yet and nor was it shown to us in school due to online class. pls help me understand what PCM is the conclusion below is just a part of a sample study our teacher gave to help us understand though it was really quite confusing, Plss help
. Conclusions
Two composite PCMs of SAT/EG and SAT/GO/EG were prepared in this article. Their thermophysical characteristic and solar-absorbing performance were investigated. Test results indicated that GO showed little effect on the thermal properties and solar absorption performance of composite PCM. However, it can significantly improve the shape stability of composite PCM. The higher the density is, the larger the volumetric heat storage capacity. When the density increased to 1 g/ cm3 , SAT/EG showed severe leakage while SAT/GO/EG can still keep the shape stability. A novel solar water heating system was designed using SAT/GO/EG (1 g/cm3 ) as the solar-absorbing substance and thermal storage media simultaneously. Under the real solar radiation, the PCM gave a high solar-absorbing efficiency of 63.7%. During a heat exchange process, the temperature of 10 L water can increase from 25 °C to 38.2 °C within 25 min. The energy conversion efficiency from solar radiation into heat absorbed by water is as high as 54.5%, which indicates that the novel system exhibits great application effects, and the composite PCM of SAT/GO/EG is very promising in designing this novel water heating system.
PCM stands for Phase Changing Material, which is a material that can absorb or release a large amount of heat energy when it undergoes a phase change.
A composite PCM, on the other hand, is a mixture of two or more PCMs that exhibit improved thermophysical properties and can be used for various applications. In the research study mentioned in the question, two composite PCMs were investigated: SAT/EG and SAT/GO/EG. SAT stands for stearic acid, EG for ethylene glycol, and GO for graphene oxide.
These composite PCMs were tested for their thermophysical characteristics and solar-absorbing performance. The results showed that GO had little effect on the thermal properties and solar absorption performance of composite PCM, but it significantly improved the shape stability of the composite PCM.
To know more about PCM visit:-
https://brainly.com/question/32700586
#SPJ11
Q3 :( 3 Marks) Draw the circuit of three phase transmission line. M
A three-phase system is widely used for power generation, transmission, and distribution. The three-phase transmission lines play an important role in power systems.
Here is a brief overview of a three-phase transmission line.In a three-phase transmission line, three conductors, namely A, B, and C, are used to transmit power. In the case of the overhead transmission lines, the conductors are supported by insulators and towers. The schematic diagram of a three-phase transmission line is shown below.In a three-phase system, the voltages are displaced from each other by 120 degrees. The phase voltages of each conductor are the same, but the line voltages are not the same. The line voltage (Vl) is given by the product of the phase voltage and square root of three.
Therefore, Vl = √3 x Vp. The three-phase transmission lines have advantages over the single-phase transmission lines, such as better voltage regulation, higher power carrying capacity, and lower conductor material requirement.
To know more about phase visit :
https://brainly.com/question/32655072
#SPJ11
What is the type number of the following system: G(s) = (s +2) /s^2(s +8) (A) 0 (B) 1 (C) 2 (D) 3
To determine the type number of a system, we need to count the number of integrators in the open-loop transfer function. The system has a total of 2 integrators.
Given the transfer function G(s) = (s + 2) / (s^2 * (s + 8)), we can see that there are two integrators in the denominator (s^2 and s). The numerator (s + 2) does not contribute to the type number.
Therefore, the system has a total of 2 integrators.
The type number of a system is defined as the number of integrators in the open-loop transfer function plus one. In this case, the type number is 2 + 1 = 3.
The correct answer is (D) 3.
Learn more about integrators here
https://brainly.com/question/28992365
#SPJ11
Refrigerant −134 a expands through a valve from a state of saturated liquid (quality x =0) to a pressure of 100kpa. What is the final quality? Hint: During this process enthalpy remains constant.
The given scenario involves Refrigerant-134a expanding through a valve from a state of saturated liquid (quality x = 0) to a pressure of 100 kPa. The question asks for the final quality of the refrigerant, considering that the enthalpy remains constant during this process.
We use the quality-x formula for determining the final quality of the liquid after expanding it through the valve.
The quality-x formula is defined as follows:
x2 = x1 + (h2 - h1)/hfgwhere x1 is the initial quality of the liquid, which is zero in this case; x2 is the final quality of the liquid; h1 is the enthalpy of the liquid at the initial state; h2 is the enthalpy of the liquid at the final state; and hfg is the enthalpy of vaporization.
It is mentioned that the enthalpy remains constant. So, h1 = h2 = h. Now, the formula becomes:x2 = x1 + (h - h1)/hfgBut h = h1.
Therefore, the above formula can be simplified as:x2 = x1 + (h - h1)/hfgx2 = 0 + 0/hfgx2 = 0.
This implies that the final quality of the refrigerant is zero. Hence, the final state of the refrigerant is saturated liquid.
Learn more about Refrigerant-134a:
https://brainly.com/question/32222757
#SPJ11
2. Write the steps necessary, in proper numbered sequence, to properly locate and orient the origin of a milled part (PRZ) on your solid model once your "Mill Part Setup" and "Stock" has been defined. Only write in the steps you feel are necessary to accomplish the task. Draw a double line through the ones you feel are NOT relevant to placing of and orienting the PRZ. 1 Select Origin type to be used 2 Select Origin tab 3 Create features 4 Create Stock 5 Rename Operations and Operations 6 Refine and Reorganize Operations 7 Generate tool paths 8 Generate an operation plan 9 Edit mill part Setup definition 10 Create a new mill part setup 11 Select Axis Tab to Reorient the Axis
The steps explained here will help in properly locating and orienting the origin of a milled part (PRZ) on your solid model once your "Mill Part Setup" and "Stock" has been defined.
The following are the steps necessary, in proper numbered sequence, to properly locate and orient the origin of a milled part (PRZ) on your solid model once your "Mill Part Setup" and "Stock" has been defined:
1. Select Origin type to be used
2. Select Origin tab
3. Create features
4. Create Stock
5. Rename Operations and Operations
6. Refine and Reorganize Operations
7. Generate tool paths
8. Generate an operation plan
9. Edit mill part Setup definition
10. Create a new mill part setup
11. Select Axis Tab to Reorient the Axis
Explanation:The above steps are necessary to properly locate and orient the origin of a milled part (PRZ) on your solid model once your "Mill Part Setup" and "Stock" has been defined. For placing and orienting the PRZ, the following steps are relevant:
1. Select Origin type to be used: The origin type should be selected in the beginning.
2. Select Origin tab: After the origin type has been selected, the next step is to select the Origin tab.
3. Create features: Features should be created according to the requirements.
4. Create Stock: Stock should be created according to the requirements.
5. Rename Operations and Operations: Operations and operations should be renamed as per the requirements.
6. Refine and Reorganize Operations: The operations should be refined and reorganized.
7. Generate tool paths: Tool paths should be generated for the milled part.
8. Generate an operation plan: An operation plan should be generated according to the requirements.
9. Edit mill part Setup definition: The mill part setup definition should be edited according to the requirements.
10. Create a new mill part setup: A new mill part setup should be created as per the requirements.
11. Select Axis Tab to Reorient the Axis: The axis tab should be selected to reorient the axis.
To know more about Stock visit:
brainly.com/question/31940696
#SPJ11
please answer asap and correctly! must show detailed steps.
Find the Laplace transform of each of the following time
functions. Your final answers must be in rational form.
Unfortunately, there is no time function mentioned in the question.
However, I can provide you with a detailed explanation of how to find the Laplace transform of a time function.
Step 1: Take the time function f(t) and multiply it by e^(-st). This will create a new function, F(s,t), that includes both time and frequency domains. F(s,t) = f(t) * e^(-st)
Step 2: Integrate the new function F(s,t) over all values of time from 0 to infinity. ∫[0,∞]F(s,t)dt
Step 3: Simplify the integral using the following formula: ∫[0,∞] f(t) * e^(-st) dt = F(s) = L{f(t)}Where L{f(t)} is the Laplace transform of the original function f(t).
Step 4: Check if the Laplace transform exists for the given function. If the integral doesn't converge, then the Laplace transform doesn't exist .Laplace transform of a function is given by the formula,Laplace transform of f(t) = ∫[0,∞] f(t) * e^(-st) dt ,where t is the independent variable and s is a complex number that is used to represent the frequency domain.
Hopefully, this helps you understand how to find the Laplace transform of a time function.
To know more about function visit :
https://brainly.com/question/31062578
#SPJ11
The average flow speed in a constant-diameter section of the pipeline is 2.5 m/s. At the inlet, the pressure is 2000 kPa (gage) and the elevation is 56 m; at the outlet, the elevation is 35 m. Calculate the pressure at the outlet (kPa, gage) if the head loss = 2 m. The specific weight of the flowing fluid is 10000N/m³. Patm = 100 kPa.
The pressure at the outlet (kPa, gage) can be calculated using the following formula:
Pressure at the outlet (gage) = Pressure at the inlet (gage) - Head loss - Density x g x Height loss.
The specific weight (γ) of the flowing fluid is given as 10000N/m³.The height difference between the inlet and outlet is 56 m - 35 m = 21 m.
The head loss is given as 2 m.Given that the average flow speed in a constant-diameter section of the pipeline is 2.5 m/s.Given that Patm = 100 kPa.At the inlet, the pressure is 2000 kPa (gage).
Using Bernoulli's equation, we can find the pressure at the outlet, which is given as:P = pressure at outlet (gage), ρ = specific weight of the fluid, h = head loss, g = acceleration due to gravity, and z = elevation of outlet - elevation of inlet.
Therefore, using the above formula; we get:
Pressure at outlet = 2000 - (10000 x 9.81 x 2) - (10000 x 9.81 x 21)
Pressure at outlet = -140810 PaTherefore, the pressure at the outlet (kPa, gage) is 185.19 kPa (approximately)
In this question, we are given the average flow speed in a constant-diameter section of the pipeline, which is 2.5 m/s. The pressure and elevation are given at the inlet and outlet. We are supposed to find the pressure at the outlet (kPa, gage) if the head loss = 2 m.
The specific weight of the flowing fluid is 10000N/m³, and
Patm = 100 kPa.
To find the pressure at the outlet, we use the formula:
P = pressure at outlet (gage), ρ = specific weight of the fluid, h = head loss, g = acceleration due to gravity, and z = elevation of outlet - elevation of inlet.
The specific weight (γ) of the flowing fluid is given as 10000N/m³.
The height difference between the inlet and outlet is 56 m - 35 m = 21 m.
The head loss is given as 2 m
.Using the above formula; we get:
Pressure at outlet = 2000 - (10000 x 9.81 x 2) - (10000 x 9.81 x 21)
Pressure at outlet = -140810 PaTherefore, the pressure at the outlet (kPa, gage) is 185.19 kPa (approximately).
The pressure at the outlet (kPa, gage) is found to be 185.19 kPa (approximately) if the head loss = 2 m. The specific weight of the flowing fluid is 10000N/m³, and Patm = 100 kPa.
Learn more about head loss here:
brainly.com/question/33310879
#SPJ11
MatLab Question, I have most of the lines already just need help with the last part and getting the four plots that are needed. The file is transient.m and the case is for Bi = 0.1 and Bi = 10 for N = 1 and N = 20.
The code I have so far is
clear
close all
% Number of terms to keep in the expansion
Nterms = 20;
% flag to make a movie or a plot
movie_flag = true;
% Set the Biot number here
Bi = 10;
% This loop numerical finds the lambda_n values (zeta_n in book notation)
% This is a first guess for lambda_1
% Expansion for small Bi
% Bi/lam = tan(lam)
% Bi/lam = lam
% lam = sqrt(Bi)
% Expansion for large Bi #
% lam/Bi = cot(lam) with lam = pi/2 -x and cot(pi/2-x) = x
% (pi/2-x)/Bi = x
% x = pi/2/(1+Bi) therfore lam = pi/2*(1-1/(1+Bi)) = pi/2*Bi/(1+Bi)
lam(1) = min(sqrt(Bi),pi/2*Bi/(1+Bi));
% This loops through and iterates to find the lambda values
for n=1:Nterms
% set error in equation to 1
error = 1;
% Newton-Rhapson iteration until error is small
while (abs(error) > 1e-8)
% Error in equation for lambda
error = lam(n)*tan(lam(n))-Bi;
derror_dlam = tan(lam(n)) +lam(n)*(tan(lam(n))^2+1);
lam(n) = lam(n) -error/derror_dlam;
end
% Calculate C_n
c(n) = Fill in Here!!!
% Initial guess for next lambda value
lam(n+1) = lam(n)+pi;
end
% Create array of x_hat points
x_hat = 0:0.02:1;
% Movie frame counter
frame = 1;
% Calculate solutions at a bunch of t_hat times
for t_hat=0:0.01:1.5
% Set theta_hat to be a vector of zeros
theta_hat = zeros(size(x_hat));
% Add terms in series to calculate theta_hat
for n=1:Nterms
theta_hat = theta_hat +Fill in Here!!!
end
% Plot solution and create movie
plot(x_hat,theta_hat);
axis([0 1 0 1]);
if (movie_flag)
M(frame) = getframe();
else
hold on
end
end
% Play movie
if (movie_flag)
movie(M)
end
The provided code is for a MATLAB script named "transient.m" that aims to generate plots for different cases of the Biot number (Bi) and the number of terms (N) in an expansion. The code already includes the necessary calculations for the lambda values and the x_hat points.
However, the code is missing the calculation for the C_nc(n) term and the term to be added in the series for theta_hat. Additionally, the code includes a movie_flag variable to switch between creating a movie or a plot. To complete the code and generate the desired plots, you need to fill in the missing calculations for C_nc(n) and the series term to be added to theta_hat. These calculations depend on the specific equation or algorithm you are working with. Once you have determined the formulas for C_nc(n) and the series term, you can incorporate them into the code. After completing the code, the script will generate plots for different values of the Biot number (Bi) and the number of terms (N). The plots will display the solution theta_hat as a function of the x_hat points. The axis limits of the plot are set to [0, 1] for both x and theta_hat. If the movie_flag variable is set to true, the code will create a movie by capturing frames of the plot at different t_hat times. The frames will be stored in the M variable, and the movie will be played using the movie(M) command. By running the modified script, you will obtain the desired plots for the specified cases of Bi and N.
Learn more about algorithm here:
https://brainly.com/question/21172316
#SPJ11
A contractor manufacturing company purchased a production equipment for $450,000 to meet the specific needs of a customer that had awarded a 4-year contract with the possibility of extending the contract for another 4 years. The company plans to use the MACRS depreciation method for this equipment as a 7-year property for tax purposes. The combined income tax rate for the company is 24%, and it expects to have an after-tax rate of return of 8% for all its investments. The equipment generated a yearly revenue of $90,000 for the first 4 years. The customer decided not to renew the contract after 4 years. Consequently, the company decided to sell the equipment for $220,000 at the end of 4 years. Answer the following questions, (a) Show before tax cash flows (BTCF) from n= 0 to n=4 (b) Calculate depreciation charges (c) Compute depreciation recapture or loss (d) Find taxable incomes and income taxes (e) Show after-tax cash flows (ATCF). (f) Determine either after tax NPW or after-tax rate of return for this investment and indicate if the company obtained the expected after-tax rate of retum
a) Before-tax cash flows (BTCF) from n= 0 to n=4Year
RevenueDepreciationBTCF0-$450,000-$450,0001$90,000$57,144$32,8562$90,000$82,372$7,6283$90,000$59,013$30,9874$90,000$28,041$61,959
b) Depreciation charges
Using the MACRS depreciation method, the annual depreciation expenses are as follows:Year
Depreciation rate Depreciation charge1 14.29% $64,215.002 24.49% $110,208.753 17.49% $78,705.754 12.49% $56,216.28Therefore, the total depreciation charge over 4 years is $309,345.75.
c) Depreciation recapture or loss
After 4 years, the equipment was sold for $220,000. The adjusted basis of the equipment is the initial cost minus the accumulated depreciation, which is:$450,000 - $309,345.75 = $140,654.25Therefore, the depreciation recapture or loss is:$220,000 - $140,654.25 = $79,345.75The depreciation recapture is positive and hence, the company must report this as ordinary income in the current tax year.
d) Taxable incomes and income taxesYearRevenueDepreciationBTCFTaxable IncomeTax1$90,000$64,215.00$25,785.00$6,187.60(24% x $25,785.00)2$90,000$110,208.75-$20,208.75-$4,850.10(24% x -$20,208.75)3$90,000$78,705.75$11,294.25$2,710.22(24% x $11,294.25)4$90,000$56,216.28$33,783.72$8,107.69(24% x $33,783.72)
The total income taxes paid over 4 years is $21,855.61.e) After-tax cash flows (ATCF)YearBTCFTaxIncome TaxATCF0-$450,000-$450,0001$32,856$6,188$26,6692$7,628$4,850$2,7793$30,987$2,710$28,2774$61,959$8,108$53,851The total ATCF over 4 years is $110,576.f)
After-tax NPW or After-tax rate of return (ARR) for this investmentAfter-tax NPW = -$450,000 + $110,576(P/A,8%,4 years)= -$450,000 + $110,576(3.3121)= -$28,128.04Since the NPW is negative, the company did not obtain the expected after-tax rate of return.
Learn more about Before-tax cash flows (BTCF) here:
brainly.com/question/16005797
#SPJ11
A heat engine operating on a Carnot Cycle rejects 519 kJ of heat to a low-temperature sink at 304 K per cycle. The high-temperature source is at 653°C. Determine the thermal efficiency of the Carnot engine in percent.
The thermal efficiency of the Carnot engine, operating on a Carnot Cycle and rejecting 519 kJ of heat to a low-temperature sink at 304 K per cycle, with a high-temperature source at 653°C, is 43.2%.
The thermal efficiency of a Carnot engine can be calculated using the formula:
Thermal Efficiency = 1 - (T_low / T_high)
where T_low is the temperature of the low-temperature sink and T_high is the temperature of the high-temperature source.
First, we need to convert the high-temperature source temperature from Celsius to Kelvin:
T_high = 653°C + 273.15 = 926.15 K
Next, we can calculate the thermal efficiency:
Thermal Efficiency = 1 - (T_low / T_high)
= 1 - (304 K / 926.15 K)
≈ 1 - 0.3286
≈ 0.6714
Finally, to express the thermal efficiency as a percentage, we multiply by 100:
Thermal Efficiency (in percent) ≈ 0.6714 * 100
≈ 67.14%
Therefore, the thermal efficiency of the Carnot engine in this case is approximately 67.14%.
Learn more about engine here: https://brainly.com/question/13147553
#SPJ11