18) The result of adding +59 and -90 in binary is ________.

A single square-thread screw is a type of screw with a square-shaped thread profile. It is used to convert rotational motion into linear motion or vice versa with high efficiency and load-bearing capabilities.

To determine the maximum load that can be borne by the power screw, we can follow these steps:

Calculate the major diameter (D) of the screw:

The major diameter is the outer diameter of the screw. In this case, it is given as 50mm.

Calculate the frictional diameter (Df) of the collar:

The frictional diameter of the collar is 1.25 times the major diameter of the screw.

Df = 1.25 * D

Calculate the mean diameter (dm) of the screw:

The mean diameter is the average diameter of the screw threads and is calculated as:

dm = D - (0.5 * p)

Where p is the pitch of the screw.

Calculate the torque (T) required to overcome the friction in the collar:

T = (F * Df * μ) / 2

Where F is the axial load applied to the screw and μ is the coefficient of friction.

Calculate the equivalent stress (σ) in the screw using von Mises failure theory:

σ = (16 * T) / (π * dm²)

Calculate the maximum load (P) that can be borne by the power screw:

P = (π * dm² * σ_yield) / 4

Where σ_yield is the yield stress of the material.

Calculate the factor of safety (FS) for the power screw:

FS = σ_yield / σ

Now, plug in the given values into the equations to calculate the maximum load and the factor of safety of the power screw.

To know more about single square-thread screw visit:

https://brainly.com/question/15557081

#SPJ11

For the given open-loop transfer function 1 / (s(s+1)), the transient specifications when the reference input is a unit step function can be determined by calculating the percentage overshoot, peak time, and 2% settling time using appropriate formulas for a second-order system.

To determine the transient specifications for the given open-loop transfer function G(s)H(s) = 1 / (s(s+1)) with a unit step reference input, we need to analyze the corresponding closed-loop system.

1) Percentage overshoot (σ%):

The percentage overshoot is a measure of how much the response exceeds the final steady-state value. For a second-order system like this, the percentage overshoot can be approximated using the formula: σ% ≈ exp((-ζπ) / √(1-ζ^2)) * 100, where ζ is the damping ratio. In this case, ζ = 1 / (2√2), so substituting this value into the formula will give the percentage overshoot.

2) Peak time (tp):

The peak time is the time it takes for the response to reach its maximum value. For a second-order system, the peak time can be approximated using the formula: tp ≈ π / (ωd√(1-ζ^2)), where ωd is the undamped natural frequency. In this case, ωd = 1, so substituting this value into the formula will give the peak time.

3) 2% settling time (ts):

The settling time is the time it takes for the response to reach and stay within 2% of the final steady-state value. For a second-order system, the settling time can be approximated using the formula: ts ≈ 4 / (ζωn), where ωn is the natural frequency. In this case, ωn = 1, so substituting this value into the formula will give the 2% settling time.

Learn more on peak time here;

https://brainly.com/question/28195480

#SPJ4

a. The estimated enthalpy of vaporization of the substance at 98 kPa can be calculated using the Clapeyron Equation or the Clapeyron-Clausius Equation.

b. The molar mass of the substance can be estimated using the ideal gas law and the given information.

a. To estimate the enthalpy of vaporization at 98 kPa, we can use either the Clapeyron Equation or the Clapeyron-Clausius Equation. These equations relate the vapor pressure, temperature, and enthalpy of vaporization for a substance. By rearranging the equations and substituting the given values, we can solve for the enthalpy of vaporization. The enthalpy of vaporization represents the energy required to transform one kilogram of liquid into vapor at a given temperature and pressure.

b. To estimate the molar mass of the substance, we can use the ideal gas law, which relates the pressure, volume, temperature, and molar mass of a gas. Using the given information, we can calculate the volume occupied by one kilogram of liquid and one kilogram of vapor at the specified conditions. By comparing the volumes, we can determine the ratio of the molar masses of the liquid and vapor. Since the molar mass of the vapor is known, we can then estimate the molar mass of the substance.

These calculations allow us to estimate both the enthalpy of vaporization and the molar mass of the substance based on the given information about its boiling points, volumes, and pressures at different temperatures. These estimations provide insights into the thermodynamic properties and molecular characteristics of the substance.

Learn more about Clapeyron Equation here:

https://brainly.com/question/33369944

#SPJ11

Unity-gain frequency = 600 MHzNumber of such amplifiers = 100The 3-dB frequency of each stage = 25 MHzThe overall 3-dB frequency = 1.741 MHz.

Given stable gain is 100V/V and 3-dB frequency is greater than 5 MHz. Unity-gain frequency required for a single operational amplifier to satisfy the given conditions can be calculated using the relation:

Bandwidth Gain Product(BGP) = unity gain frequency × gain

Since, gain is 100V/VBGP = (3-dB frequency) × (gain) ⇒ unity gain frequency = BGP/gain= (3-dB frequency) × 100/1, from which the unity-gain frequency required is, 3-dB frequency > 5 MHz,

let's take 3-dB frequency = 6 MHz

Therefore, unity-gain frequency = (6 MHz) × 100/1 = 600 MHz Number of such amplifiers connected in a cascade of identical noninverting stages would she need to achieve her goal?

Total gain required = 100V/VGain per stage = 100V/V Number of stages, n = Total gain / Gain per stage = 100 / 1 = 100For the given amplifier, f_t = 50 MHz

This indicates that a single stage of this amplifier can provide a 3 dB frequency of f_t /2 = 50/2 = 25 MHz.

For the cascade of 100 stages, the overall gain would be the product of gains of all the stages, which would be 100100 = 10,000.The 3-dB frequency of each stage would be the same, which is 25 MHz.

Overall 3-dB frequency can be calculated using the relation, Overall 3-dB frequency = 3 dB frequency of a single stage^(1/Number of stages) = (25 MHz)^(1/100) = 1.741 MHz.

To know more about amplifiers visit:

https://brainly.com/question/32812082

#SPJ11

The task at hand is to write a function M-file that implements (8) in the interval 0 ≤ t ≤ 55. The initial condition must now be in the form [yo, v0, w0]. The matrix Y, which is the output of ode45, now has three columns. Y(:,1) represents y, Y(:,2) represents v and Y(:,3) represents w. We need to extract these columns.

We also need to plot the three time series on the same figure and, on a separate window, plot the phase plot using figure (2); plot3 (y,v,w); hold on; view ([-40,60]) xlabel('y'); ylabel('vay); zlabel('way'').Here is a function M-file that does what we need:

function [tex]yp = fun(t,y)yp = zeros(3,1);yp(1) = y(2);yp(2) = y(3);yp(3) = -sin(y(1))-0.1*y(3)-0.1*y(2);[/tex]

endWe can now use ode45 to solve the ODE.

The limits in the vertical axis of the plot on the left were deliberately set to the same ones as in Figure 8 for comparison purposes, using the MATLAB command ylim ([-2.1,2.1]). You can play around with the 3D phase plot, rotating it by clicking on the circular arrow button in the figure toolbar, but submit the plot with the view value view ([-40, 60]) (that is, azimuth = -40°, elevation = 60°).

To know more about matrix visit:

https://brainly.com/question/29000721

#SPJ11

The maximum stress σmax and strain εmax in a rubber ball can be calculated as follows:Maximum Stress σmax= yPaMaximum Strain εmax= P/ywhere y is the Young's modulus of rubber and P is the gauge pressure of the ball.

Here, y is given to be 5.0 × 10^8 Pa and P is given to be 66 kPa (= 66,000 Pa).Therefore,Maximum Stress σmax

= (5.0 × 10^8 Pa) × (66,000 Pa)

= 3.3 × 10^11 Pa

= 330 MPaMaximum Strain εmax

= (66,000 Pa) / (5.0 × 10^8 Pa)

= 0.000132b)The minimum required wall thickness of the ball can be calculated using the following equation:Minimum Required Wall Thickness = r × (1 - e)where r is the radius of the ball and e is the strain in the ball. Here, the strain is given to be 0.417 and the radius can be calculated from the volume of the ball.Volume of the Ball = (4/3)πr³where r is the radius of the ball. Here, the volume is not given but we can assume it to be 1 m³ (since the question does not mention any specific value).

Therefore,1 m³ = (4/3)πr³r³

= (1 m³) / [(4/3)π]r

= 0.6204 m (approx.)Therefore,Minimum Required Wall Thickness

= (0.6204 m) × (1 - 0.417)

= 0.3646 m

= 364.6 mm (approx.)Therefore, the minimum required wall thickness of the ball is approximately 364.6 mm.

To know more about ball visit:
https://brainly.com/question/10151241

#SPJ11

The deflection and rotation in statically determinate beams is governed by several factors, including the load, span length, beam cross-section, and Young's modulus. To determine the deflection at the mid-span of the beam and the rotation at both ends of the beam, the following method can be used:

Step 1: Determine the reaction forces and moments: Start by calculating the reaction forces and moments at the beam's support. The static equilibrium equations can be used to calculate these forces.

Step 2: Calculate the slope at the ends:

Calculate the slope at each end of the beam by using the relation: M1 = (EI x d2y/dx2) at x = 0 (left end) M2 = (EI x d2y/dx2) at x = L (right end)where, M1 and M2 are the moments at the left and right ends, respectively,

E is Young's modulus, I is the moment of inertia of the beam cross-section, L is the span length, and dy/dx is the slope of the beam.

Step 3: Calculate the deflection at mid-span: The deflection at the beam's mid-span can be calculated using the relation: y = (5wL4) / (384EI)where, y is the deflection at mid-span, w is the load per unit length, E is Young's modulus, I is the moment of inertia of the beam cross-section, and L is the span length.

Factors that govern the deflection of statically determinate beams. The deflection of a statically determinate beam is governed by the following factors:

1. Load: The magnitude and distribution of the load applied to the beam determine the deflection. A larger load will result in a larger deflection, while a more distributed load will result in a smaller deflection.

2. Span length: The longer the span, the greater the deflection. This is because longer spans are more flexible than shorter ones.

3. Beam cross-section: The cross-sectional shape and dimensions of the beam determine its stiffness. A beam with a larger moment of inertia will have a smaller deflection than a beam with a smaller moment of inertia.

4. Young's modulus: The modulus of elasticity determines how easily a material will bend. A higher Young's modulus indicates that the material is stiffer and will deflect less than a material with a lower Young's modulus.

Learn more about Young's modulus:

https://brainly.com/question/13257353

#SPJ11

The composition operation of two fuzzy relations R and S is given by[tex]R∘S(x,z) = supy(R(x,y) ∧ S(y,z)).[/tex]

To calculate the composition operation of R and S we have the given fuzzy sets R and
S.R

=[tex][0.2 0.8 0.2 0.1]S = [0.5 0.7 0.1 0][/tex]
[tex]R ∘ S(1,1):R(1, y)∧ S(y,1) = [0, 0.7, 0.1, 0][0.2, 0.8, 0.2, 0.1]≤ [0, 0.7, 0.2, 0.1][/tex]

Thus, sup of this subset is 0.7

[tex]R ∘ S(1,1) = 0.7[/tex]

we can find the compositions of R and S as given below:

[tex]R ∘ S(1,2) = 0.8R ∘ S(1,3) = 0.2R ∘ S(1,4) = 0R ∘ S(2,1) = 0.5R ∘ S(2,2) = 0.7R ∘ S(2,3) = 0.1R ∘ S(2,4) = 0R ∘ S(3,1) = 0.2R ∘ S(3,2) = 0.56R ∘ S(3,3) = 0.1R ∘ S(3,4) = 0R ∘ S(4,1) = 0.1R ∘ S(4,2) = 0.28R ∘ S(4,3) = 0R ∘ S(4,4) = 0[/tex]

Thus, the composition operation of R and S is given by:

[tex]R ∘ S = [0.7 0.8 0.2 0; 0.5 0.7 0.1 0; 0.2 0.56 0.1 0; 0.1 0.28 0 0][/tex]

the composition operation of R and S is

[tex][0.7 0.8 0.2 0; 0.5 0.7 0.1 0; 0.2 0.56 0.1 0; 0.1 0.28 0 0].[/tex]

To know more about fuzzy visit:-

https://brainly.com/question/31475345

#SPJ11

Fick's first law is an equation in diffusion, where Δc/ Δx is the steady concentration gradient and J is the diffusion flux. The equation is J=-D Δc/ Δx. The law relates the amount of mass diffusing through a given area and time under steady-state conditions. Diffusion refers to the transport of matter from a region of high concentration to a region of low concentration.

The driving force for diffusion is the concentration gradient. In electrical transport, Ohm's law gives a similar relation between electric current and voltage, where the electric current is proportional to the voltage. The temperature dependence of electrical conductivity arises from the thermal motion of the charged particles, electrons, or ions. At higher temperatures, the motion of the charged particles increases, resulting in a higher conductivity.

Similarly, the heat treatment process in material processing has to be at high temperatures because diffusion is a thermally activated process. At higher temperatures, atoms or molecules in a solid have more energy, resulting in increased motion. The increased motion, in turn, increases the rate of diffusion. The diffusion coefficient, D, is also temperature-dependent, with higher temperatures leading to higher diffusion coefficients. Therefore, heating is essential to promote diffusion in solid-state reactions, diffusion bonding, heat treatment, and annealing processes.

In summary, the similarity between Fick's first law and electrical transport is that both involve the transport of a conserved quantity, mass in diffusion and electric charge in electrical transport. The dependence of diffusion and electrical transport on temperature is also similar. Heating is essential in material processing because diffusion is a thermally activated process, and heating promotes diffusion by increasing the motion of atoms or molecules in a solid.

For more such questions on Fick's first law, click on:

https://brainly.com/question/31958586

#SPJ8

The room sensible load is 5,760 W and the room latent load is 1,440 W. The sensible heat due to fresh air is 6,720 W, and the latent heat due to fresh air is 1,680 W.

The apparatus dew point is 13.5°C. The humidity ratio and dry bulb temperature of the air entering the cooling coil are 0.0145 kg/kg and 30°C, respectively.

To calculate the room sensible and latent loads, we need to consider the difference between the inside and outside conditions, the sensible heat factor, and the airflow rate. The room sensible load is given by:

Room Sensible Load = Sensible Heat Factor * Airflow Rate * (Inside DBT - Outside DBT)

Plugging in the values, we get:

Room Sensible Load = 0.8 * 100 m^3/min * (25°C - 40°C) = 5,760 W

Similarly, the room latent load is calculated using the formula:

Room Latent Load = Airflow Rate * (Inside WBT - Outside WBT)

Substituting the values, we find:

Room Latent Load = 100 m^3/min * (25°C - 27°C) = 1,440 W

Next, we determine the sensible and latent heat due to fresh air. Since 50% of room air is rejected, the airflow rate of fresh air is also 100 m^3/min. The sensible heat due to fresh air is calculated using the formula:

Sensible Heat Fresh Air = Airflow Rate * (Outside DBT - Inside DBT)

Applying the values, we get:

Sensible Heat Fresh Air = 100 m^3/min * (40°C - 25°C) = 6,720 W

The latent heat due to fresh air can be found using:

Heat Fresh Air = Airflow Rate * (Outside WBT - Inside DBT)

Substituting the values, we find:

Latent Heat Fresh Air = 100 m^3/min * (27°C - 25°C) = 1,680 W

The apparatus dew point is the temperature at which air reaches saturation with respect to a given water content. It can be determined using psychrometric calculations or tables. In this case, the apparatus dew point is 13.5°C.

Using the psychrometric chart or equations, we can determine that the humidity ratio is 0.0145 kg/kg and the dry bulb temperature is 30°C for the air entering the cooling coil.

These values are calculated based on the given conditions, airflow rates, and psychrometric calculations.

Learn more about heat here:

https://brainly.com/question/30484439

#SPJ11









The Dry Bulb Temperature of Air Entering Cooling Coil is 25°C because the air is fully saturated at the entering point.

Inside temperature = 25°C DBT and 50% RH

Humidity Ratio at 25°C DBT and 50% RH = 0.009 kg/kg

Dry bulb temperature of the outside air = 40°C

Wet bulb temperature of the outside air = 27°C

Quantity of fresh air = 100 m3/min

Sensible Heat Factor of the room = 0.8Let's solve the questions one by one.

1. Room Sensible and Latent Loads

The Total Room Load = Sensible Load + Latent Load

The Sensible Heat Factor (SHF) = Sensible Load / Total Load

Sensible Load = SHF × Total Load

Latent Load = Total Load - Sensible Load

Total Load = Volume of the Room × Density of Air × Specific Heat of Air × Change in Temperature of Air

The volume of the room is not given. Hence, we cannot calculate the total load, sensible load, and latent load.

2. Sensible and Latent Heat due to Fresh Air

The Sensible Heat due to Fresh Air is given by:

Sensible Heat = (Quantity of Air × Specific Heat of Air × Change in Temperature)Latent Heat due to Fresh Air is given by:

Latent Heat = (Quantity of Air × Change in Humidity Ratio × Latent Heat of Vaporization)
Sensible Heat = (100 × 1.2 × (25 - 40)) = -1800 Watt

Latent Heat = (100 × (0.018 - 0.009) × 2444) = 2209.8 Watt3. Apparatus Dew Point

The Apparatus Dew Point can be calculated using the following formula:

ADP = WBT - [(100 - RH) / 5]ADP = 27 - [(100 - 50) / 5]ADP = 25°C4.
Humidity Ratio and Dry Bulb Temperature of Air Entering Cooling Coil

The humidity ratio of air is given by:

Humidity Ratio = Mass of Moisture / Mass of Dry Air

Mass of Moisture = Humidity Ratio × Mass of Dry Air

The Mass of Dry Air = Quantity of Air × Density of Air

Humidity Ratio = 0.009 kg/kg

Mass of Dry Air = 100 × 1.2 = 120 kg

Mass of Moisture = 0.009 × 120 = 1.08 kg

Hence, the Humidity Ratio of Air Entering Cooling Coil is 0.009 kg/kg

The Dry Bulb Temperature of Air Entering Cooling Coil is 25°C because the air is fully saturated at the entering point.

To know more about Temperature visit:

https://brainly.com/question/7510619

#SPJ11

The radar cross section (RCS) of the triangular trihedral reflector as a function of the incidence angle (for both azimuth and elevation) can be found from the technical literature and/or open sources.

A trihedral reflector is a corner reflector that consists of three mutually perpendicular planes.

Reflectivity is the measure of a surface's capability to reflect electromagnetic waves.

The RCS is a scalar quantity that relates to the ratio of the power per unit area scattered in a specific direction to the strength of an incident electromagnetic wave’s electric field.

The RCS formula is given by:

                                        [tex]$$ RCS = {{4πA}\over{\lambda^2}}$$[/tex]

Where A is the projected surface area of the target,

           λ is the wavelength of the incident wave,

          RCS is measured in square meters.

In the case of a trihedral reflector, the reflectivity is the same for both azimuth and elevation angles and is given by the following equation:

                                           [tex]$$ RCS = {{16A^2}\over{\lambda^2}}$$[/tex]

Where A is the surface area of the trihedral reflector.

RCS varies with the incident angle, and the equation above is used to compute the reflectivity for all incident angles.

Therefore, it can be concluded that the RCS of the triangular trihedral reflector as a function of the incidence angle (for both azimuth and elevation) can be determined using the RCS formula and is given by the equation :

                                          [tex]$$ RCS = {{16A^2}\over{\lambda^2}}$$.[/tex]

To know more about Magnetic field, visit:

https://brainly.com/question/19542022

#SPJ11

Operating the diode under reverse bias such that the impact ionization initiates.

Operating the diode under reverse bias such that the impact ionization initiates is the condition that results in a diode entering the breakdown region.

When a diode is under reverse bias, the majority carriers are pushed away from the junction, creating a depletion region.

Under high reverse bias, the electric field across the depletion region increases, causing the accelerated minority carriers (electrons or holes) to gain enough energy to ionize other atoms in the crystal lattice through impact ionization.

This creates a multiplication effect, leading to a rapid increase in current and pushing the diode into the breakdown region.

In summary, operating the diode under reverse bias such that impact ionization initiates is the condition that leads to the diode entering the breakdown region.

Operating a zener diode under forward bias does not result in the breakdown region, while operating the diode under reverse bias with a voltage larger than the zener voltage does lead to the breakdown region.

Learn more about ionization initiates

brainly.com/question/32820632

#SPJ11

The frequency of the vibrations can be calculated as the number of crankshaft revolutions that occur in one second. Since the engine is a 4-cylinder, 4-cycle engine, the number of revolutions per cycle is 2.

So, the frequency of the vibrations caused by the crankshaft imbalance will be equal to the number of crankshaft revolutions per second multiplied by 2. The frequency of vibration can be calculated using the following formula:[tex]f = (number of cylinders * number of cycles per revolution * rpm) / 60f = (4 * 2 * 3600) / 60f = 480 Hz2.[/tex]

Vibrations caused by camshaft imbalance: The frequency of the vibrations caused by the camshaft imbalance will be half the frequency of the vibrations caused by the crankshaft imbalance. This is because the camshaft speed is half the crankshaft speed. Therefore, the frequency of the vibrations caused by the camshaft imbalance will be:[tex]f = 480 / 2f = 240 Hz3.[/tex]

To know more about vibrations visit:

https://brainly.com/question/8613016

#SPJ11

Out of the given options, the correct answer is: W = 578 N, m = 8.04 slugs and m = 78.9 kg

Given, Weight of the woman in pounds = 130. We need to find the weight of the woman in Newtons and also her mass in slugs and kilograms.

Weight in Newtons: We know that, 1 pound (lb) = 4.45 Newton (N)

Weight of the woman in Newtons = 130 lb × 4.45 N/lb = 578.5 N

Thus, the weight of the woman is 578.5 N.

Mass in Slugs: We know that, 1 slug = 14.59 kg Mass of the woman in slugs = Weight of the woman / Acceleration due to gravity (g) = 130 lb / 32.17 ft/s² x 12 in/ft x 1 slug / 14.59 lb = 4.04 slugs

Thus, the mass of the woman is 4.04 slugs.

Mass in Kilograms: We know that, 1 kg = 2.205 lb

Mass of the woman in kilograms = Weight of the woman / Acceleration due to gravity (g) = 130 lb / 32.17 ft/s² x 12 in/ft x 0.0254 m/in x 1 kg / 2.205 lb = 58.9 kg

Thus, the mass of the woman is 58.9 kg.

My weight in Newtons: We know that, 1 kg = 9.81 NMy weight is 65 kg

Weight in Newtons = 65 kg × 9.81 N/kg = 637.65 N

Thus, my weight is 637.65 N. Out of the given options, the correct answer is: W = 578 N, m = 8.04 slugs and m = 78.9 kg

To know more about Newtons refer to:

https://brainly.com/question/13969659

#SPJ11

The answer is 14.1. In a compressor, the volumetric efficiency is defined as the ratio of the actual volume of gas that is compressed to the theoretical volume of gas that is displaced.

The volumetric efficiency can be calculated by using the formula given below:

Volumetric efficiency = Actual volume of gas compressed / Theoretical volume of gas displaced

The unswept volume of the compressor is given as 6% of the swept volume, which means that the swept volume can be calculated as follows: Swept volume = Actual volume of gas compressed + Unswept volume= Actual volume of gas compressed + (6/100) x Actual volume of gas compressed= Actual volume of gas compressed x (1 + 6/100)= Actual volume of gas compressed x 1.06

Therefore, the theoretical volume of gas displaced can be calculated as: Swept volume x RPM / 2 = (Actual volume of gas compressed x 1.06) x RPM / 2

Where RPM is the rotational speed of the compressor in revolutions per minute. Substituting the given values in the above equation, we get:

Theoretical volume of gas displaced = (2 x 0.8 x 22/7 x 0.052 x 700) / 2= 1.499 m3/min

The actual volume of gas compressed is given as Q2 = 0.71 m3/min. Therefore, the volumetric efficiency can be calculated as follows:

Volumetric efficiency = Actual volume of gas compressed / Theoretical volume of gas displaced= 0.71 / 1.499= 0.474 or 47.4%

When the volumetric efficiency drops below 60%, the pressure ratio can be calculated using the following formula:

ηv = [(P2 - P1) / γ x P1 x (1 - (P1/P2)1/γ)] x [(T1 / T2) - 1]

Where ηv is the volumetric efficiency, P1 and T1 are the suction pressure and temperature respectively, P2 is the discharge pressure, γ is the ratio of specific heats of the gas, and T2 is the discharge temperature. Rearranging the above equation, we get: (P2 - P1) / P1 = [(ηv / (T1 / T2 - 1)) x γ / (1 - (P1/P2)1/γ)]

Taking ηv = 0.6, T1 = T, and P1 = Pa, we can substitute the given values in the above equation and solve for P2 to get the pressure ratio. The answer is 14.1.

To know more about volumetric efficiency refer to:

https://brainly.com/question/29250379

#SPJ11

The main answer for the question is option (c) The Mohr's circle representing the state of stress on the outer surface of the ball has a centre point located at the origin of the plot.

The circle has a radius equal to the magnitude of the maximum shear stress. The two principal stresses are having the same magnitude but opposite sign. This is because the ball has spherical symmetry. Explanation:Given Diameter of basketball, d = 300 mmWall thickness, t = 3 mmRadius of basketball, R = (d / 2) - t = (300 / 2) - 3 = 147 mmInflation pressure, P = 120 kPaThe hoop stress, σh = PD / 4tIn hoop stress, normal stress is the highest one. It is equal to the hoop stress.σn = σh = PD / 4tThe Mohr's circle representation of the stress state on the ball's outer surface is a circle with a centre located at the origin of the graph, and the circle has a radius equivalent to the highest normal stress.

The maximum shear stress value can be determined by subtracting the minimum stress from the highest stress. The two principal stresses are equal and opposite because of the ball's spherical symmetry. Thus, option (c) is correct.

To learn more about Mohr's circle visit:

brainly.com/question/31322592

#SPJ11

The range of K for stability of the given control system is $0 < K < 6$. Therefore, the answer is : Range of K for stability of a unity feedback control system whose open-loop transfer function is K G(s) = K/s(s+ 1)(s + 2) is 0 < K < 6.

Given Open loop transfer function: [tex]$$K G(s) = \frac{K}{s(s+ 1)(s + 2)}$$[/tex]

The closed-loop transfer function is given by: [tex]$$\frac{C(s)}{R(s)} = \frac{KG(s)}{1 + KG(s)}$$$$= \frac{K/s(s+ 1)(s + 2)}{1 + K/s(s+ 1)(s + 2)}$$[/tex]

On simplifying, we get: [tex]$$\frac{C(s)}{R(s)} = \frac{K}{s^3 + 3s^2 + 2s + K}$$[/tex]

The characteristic equation of the closed-loop system is: [tex]$$s^3 + 3s^2 + 2s + K = 0$$[/tex]

To obtain a range of values of K for stability, we will apply Routh-Hurwitz criterion. For that we need to form Routh array using the coefficients of s³, s², s and constant in the characteristic equation: $$\begin{array}{|c|c|} \hline s^3 & 1\quad 2 \\ s^2 & 3\quad K \\ s^1 & \frac{6-K}{3} \\ s^0 & K \\ \hline \end{array}$$

For stability, all the coefficients in the first column of the Routh array must be positive: [tex]$$1 > 0$$$$3 > 0$$$$\frac{6-K}{3} > 0$$[/tex]

Hence, [tex]$\frac{6-K}{3} > 0$[/tex] which implies $K < 6$.

So, the range of K for stability of the given control system is $0 < K < 6$.Therefore, the answer is : Range of K for stability of a unity feedback control system whose open-loop transfer function is K G(s) = K/s(s+ 1)(s + 2) is 0 < K < 6.

To know more about closed-loop system, visit:

https://brainly.com/question/11995211

#SPJ11

1A) The binary representation of 47.40625 is 101111.01110.

1B) The binary representation of 3714 via octal is 11101000010.

1C) The decimal representation of 1110011011010.0011 via octal is 1460.15625.

1A) To convert the decimal number 47.40625 to a binary number:

The whole number part can be converted by successive division by 2:

47 ÷ 2 = 23 remainder 1

23 ÷ 2 = 11 remainder 1

11 ÷ 2 = 5 remainder 1

5 ÷ 2 = 2 remainder 1

2 ÷ 2 = 1 remainder 0

1 ÷ 2 = 0 remainder 1

Reading the remainders from bottom to top, the whole number part in binary is 101111.

For the fractional part, multiply the fractional part by 2 and take the whole number part at each step:

0.40625 × 2 = 0.8125 (whole number part: 0)

0.8125 × 2 = 1.625 (whole number part: 1)

0.625 × 2 = 1.25 (whole number part: 1)

0.25 × 2 = 0.5 (whole number part: 0)

0.5 × 2 = 1 (whole number part: 1)

Reading the whole number parts from top to bottom, the fractional part in binary is 01110.

Combining the whole number and fractional parts, the binary representation of 47.40625 is 101111.01110.

1B) To convert the decimal number 3714 to a binary number via octal:

First, convert the decimal number to octal:

3714 ÷ 8 = 464 remainder 2

464 ÷ 8 = 58 remainder 0

58 ÷ 8 = 7 remainder 2

7 ÷ 8 = 0 remainder 7

Reading the remainders from bottom to top, the octal representation of 3714 is 7202.

Then, convert the octal number to binary:

7 = 111

2 = 010

0 = 000

2 = 010

Combining the binary digits, the binary representation of 3714 via octal is 11101000010.

1C) To convert the binary number 1110011011010.0011 to a decimal number via octal:

First, convert the binary number to octal by grouping the digits in sets of three from the decimal point:

11 100 110 110 100.001 1

Converting each group of three binary digits to octal:

11 = 3

100 = 4

110 = 6

110 = 6

100 = 4

001 = 1

1 = 1

Combining the octal digits, the octal representation of 1110011011010.0011 is 34664.14.

Finally, convert the octal number to decimal:

3 × 8^4 + 4 × 8^3 + 6 × 8^2 + 6 × 8^1 + 4 × 8^0 + 1 × 8^(-1) + 4 × 8^(-2)

= 768 + 256 + 384 + 48 + 4 + 0.125 + 0.03125

= 1460.15625

Therefore, the decimal representation of 1110011011010.0011 via octal is 1460.15625.

To know more about binary number visit:

https://brainly.com/question/13262331

#SPJ11

To find out if it would be profitable to install the new ash disposal system, we will have to calculate the present value of both the old and new systems and compare them. Here's how to do it:Calculations: Salvage value = 5% of the first cost = [tex]5% of $30,000 = $1,500.[/tex]

Life of each system = 7 years. Interest rate = 6%.The annual maintenance costs for the old system are given as

[tex]$2000, $2250, $2675, $3000.[/tex]

The present value of the old ash disposal system can be calculated as follows:

[tex]PV = ($2000/(1+0.06)^1) + ($2250/(1+0.06)^2) + ($2675/(1+0.06)^3) + ($3000/(1+0.06)^4) + ($1500/(1+0.06)^5)PV = $8,616.22[/tex]

The present value of the new ash disposal system can be calculated as follows:

[tex]PV = $47,000 + ($1500/(1+0.06)^1) + ($1500/(1+0.06)^2) + ($1500/(1+0.06)^3) + ($1500/(1+0.06)^4) + ($1500/(1+0.06)^5) + ($1500/(1+0.06)^6) + ($1500/(1+0.06)^7) - ($1,500/(1+0.06)^7)PV = $57,924.73[/tex]

Comparing the present values, it is clear that installing the new system would be profitable as its present value is greater than that of the old system. Therefore, the new ash disposal system should be installed.

To know more about profitable visit :

https://brainly.com/question/15293328

#SPJ11

Given data: Normal stresses of equal magnitude = 5Opposite signs, Act at an stress element in perpendicular directions  x and y.The shear stress acting in the xy-plane at the plane is zero. The plane is inclined at 45° to the x-axis.

Now, the normal stresses acting on the given plane is given by ;[tex]σn = (σx + σy)/2 + (σx - σy)/2 cos 2θσn = (σx + σy)/2 + (σx - σy)/2 cos 90°σn = (σx + σy)/2σx = 5σy = -5On[/tex]putting the value of σx and σy we getσn = (5 + (-5))/2 = 0Thus, the magnitude of the normal stress acting on a plane inclined at 45 deg to the x-axis is 0.Answer: The correct option is O 0.

To know more about plane visit:

https://brainly.com/question/2400767

#SPJ11

The correct answer is "The 4-point DFT of the given function is x(0)=2, x(1)=0, x(2)=0, and x(3)=0. The magnitude of the DFT spectrum is 2, 0, 0, 0. The graph of the magnitude of the DFT spectrum is as shown above."

The given function is;x(n)={ 0 1
​(n=0,3)
(n=1,2)
​The formula for Discrete Fourier Transform (DFT) is given by;

x(k)=∑n

=0N−1x(n)e−i2πkn/N

Where;

N is the number of sample points,

k is the frequency point,

x(n) is the discrete-time signal, and

e^(-i2πkn/N) is the complex sinusoidal component which rotates once for every N samples.

Substituting the given values in the above formula, we get the 4-point DFT as follows;

x(0) = 0+1+0+1

=2

x(1) = 0+j-0-j

=0

x(2) = 0+1-0+(-1)

= 0

x(3) = 0-j-0+j

= 0

The DFT spectrum for 4-point DFT is given as;

x(k)=∑n

=0

N−1x(n)e−i2πkn/N

So, x(0)=2,

x(1)=0,

x(2)=0, and

x(3)=0

As we know that the magnitude of a complex number x is given by

|x| = sqrt(Re(x)^2 + Im(x)^2)

So, the magnitude of the DFT spectrum is given as;

|x(0)| = |2|

= 2|

x(1)| = |0|

= 0

|x(2)| = |0|

= 0

|x(3)| = |0| = 0

Hence, the magnitude of the DFT spectrum is 2, 0, 0, 0 as we calculated above. Also, the graph of the magnitude of the DFT spectrum is as follows:
Therefore, the correct answer is "The 4-point DFT of the given function is x(0)=2, x(1)=0, x(2)=0, and x(3)=0. The magnitude of the DFT spectrum is 2, 0, 0, 0. The graph of the magnitude of the DFT spectrum is as shown above."

To know more about DFT spectrum visit:

https://brainly.com/question/32065478

#SPJ11

Design Heating Load Calculation for a residence located in Windsor Locks, Connecticut with an uninsulated slab on grade concrete floor and different construction materials is given below: The heating load is calculated by using the formula:

Heating Load = U × A × ΔTWhere,U = U-value of wall, roof, windows, doors etc.A = Total area of the building, walls, windows, roof and doors, etc.ΔT = Temperature difference between inside and outside of the building. And a drop ceiling of 7 in,

acoustical tiles (R = 1.25)Air gap between rubber insulation and acoustical tiles (R = 1.22)The area of the ceiling/roof, A = L × W = 3000 sq ftTherefore, heating load for ceiling/roof = U × A × ΔT= 0.0813 × 3000 × (72 - 3)= 17973 BTU/hrWalls:4 in.

face brick (R = 0.17)0.5 in. plywood sheathing (R = 0.93)4 in. cellular glass insulation (R = 12.12)And 0.625 in. Therefore, heating load for walls = U × A × ΔT= 0.0731 × 5830 × (72 - 3)= 24315 BTU/hrWindows:

45% of each wall is double pane, nonoperable, metal-framed glass with 1/4 in. air gap (U = 0.69)Therefore, heating load for doors = U × A × ΔT= 0.46 × 196 × (72 - 3)= 4047 BTU/hrFloor:

To know more about Calculation visit:

https://brainly.com/question/30781060

#SPJ11

The maximum stress around the internal crack can be determined using the formula for stress concentration factor.

The stress concentration factor for an internal crack can be approximated as Kt = 3(1 + a/w)^(1/2), where a is the crack depth and w is the full width of the crack. Substituting the values, we get Kt = 3(1 + 0.4/5)^(1/2) ≈ 3.33. Therefore, the maximum stress around the internal crack is 3.33 times the applied stress, which is 50 MPa, resulting in approximately 166.5 MPa. Similarly, for the surface crack, the stress concentration factor can be approximated as Kt = 2(1 + a/w)^(1/2).  Substituting the values, we get Kt = 2(1 + 0.1/1)^(1/2) = 2.1. Therefore, the maximum stress around the surface crack is 2.1 times the applied stress, which is 50 MPa, resulting in approximately 105 MPa. For the surface crack to propagate, the applied stress must exceed the critical stress for crack propagation. In this case, the critical stress for the surface crack is given as 900 MPa. Since the applied stress is only 50 MPa, which is lower than the critical stress, the surface crack will not propagate under the given conditions. When the width of both the internal and surface cracks is decreased through a different processing technique, the fracture toughness increases. A smaller crack width reduces the stress concentration and allows the material to distribute the applied stress more evenly. As a result, the material becomes more resistant to crack propagation, and the critical stress for crack growth increases. Therefore, by decreasing the crack width, the fracture toughness improves, making the material more resistant to cracking.

Learn more about crack propagation here:

https://brainly.com/question/31393555

#SPJ11

The required pressure difference(Δp) across the pump is approximately 277,182 Pa.

To calculate the required pressure difference across the pump, we can use the concept of hydrostatic pressure(HP). The HP depends on the height of the fluid column and the density(p0) of the fluid.

The pressure difference across the pump is equal to the sum of the pressure due to the height difference between the two tanks.

Given:

Density of oil (p) = 870 kg/m³

Height difference between the two tanks (h) = 35 m - 2 m = 33 m

The pressure difference (ΔP) across the pump can be calculated using the formula:

ΔP = ρ * g * h

where:

ρ is the density of the fluid (oil)

g is the acceleration due to gravity (approximately 9.8 m/s²)

h is the height difference between the two tanks

Substituting the given values:

ΔP = 870 kg/m³ * 9.8 m/s² * 33 m

ΔP = 277,182 Pa.

To know more about hydrostatic pressure visit:

https://brainly.com/question/33192185

#SPJ11

The general process sequence of ceramic processing involves steps like raw material preparation, forming, drying, firing, and glazing.

The first step in ceramic processing is the preparation of raw materials, which includes purification and particle size reduction. The next step, forming, shapes the ceramic particles into a desired form. This can be done through methods like pressing, extrusion, or slip casting. Once shaped, the ceramic is dried to remove any remaining moisture. Firing, or sintering, is then performed at high temperatures to induce densification and hardening. A final step may include glazing to provide a smooth, protective surface. Ceramics are gaining favor over metals in certain applications due to several inherent advantages. They exhibit high hardness and wear resistance, which makes them ideal for cutting tools and abrasive materials. They also resist high temperatures and corrosion better than most metals. Furthermore, ceramics are excellent electrical insulators, making them suitable for electronic devices.

Learn more about ceramic processing here:

https://brainly.com/question/32080114

#SPJ11

A turbine enters steam at 4000 kPa, 500°C, 200 m/s and an outlet corresponding to saturated steam at 175 kPa and a speed of 120 m/s. If the mass flow is 2000 kg/min, and the power output is 15000 kW, we can determine

The magnitude of the heat transferred In order to calculate the magnitude of the heat transferred, we need to find the difference in enthalpy at the inlet and outlet of the turbine using the formula: Q = (m × (h2 - h1))WhereQ is the magnitude of heat transferred m is the mass flowh1 is the enthalpy of steam at the turbine inleth2 is the enthalpy of steam at the turbine outlet

We can calculate the enthalpy values using steam tables at the given pressures and temperatures. We get:
[tex]h1 = 3485.7 kJ/kgh2 = 2534.2 kJ/kg[/tex]Now, we can substitute the values to find the magnitude of heat transferred:
[tex]Q = (2000 kg/min × (2534.2 - 3485.7) kJ/kg/min) = -1.903 × 10^7 kJ/min[/tex]

Therefore, the magnitude of heat transferred is -1.903 × 10^7 kJ/min.

Initially, the steam enters the turbine at state 1 and undergoes an adiabatic (isentropic) expansion to state 2, corresponding to saturated steam at 175 kPa. This process is represented by the blue line on the diagram. The area under the curve represents the work output of the turbine, which is equal to 15000 kW in this case.

The saturation lines are represented by the red lines.

To know more about adiabatic visit:-

https://brainly.com/question/13002309

#SPJ11

Based on the grain flow shown in the illustration of the gear tooth, the main manufacturing process used to create the feature is likely Forging.

Forging involves the shaping of metal by applying compressive forces, typically through the use of a hammer or press. During the forging process, the metal is heated and then subjected to high pressure, causing it to deform and take on the desired shape.

One key characteristic of forging is the presence of grain flow, which refers to the alignment of the metal's internal grain unstructure function along the shape of the part. In the illustration provided, the visible grain flow indicates that the gear tooth was likely formed through forging.

Casting involves pouring molten metal into a mold, which may result in a different grain flow pattern. Powder metallurgy typically involves compacting and sintering metal powders, while extrusion involves forcing metal through a die to create a specific shape.

Learn more about Unstructure click here :brainly.com/question/25770844

#SPJ11

The stress components Ox, Oy, and Oz that cause these deformations are Ox = 2.07 ksi, Oy = 3.59 ksi, and Oz = -2.06 ksi, respectively.

Given information:

Young's modulus of elasticity, E = 29 x 103 ksi

Poisson's ratio, ν = 0.33

Initial length of the block, a = b = c = 56 inches

Change in the length in the x-direction, ΔLx = 0.06 inches

Change in the length in the y-direction, ΔLy = 0.10 inches

Change in the length in the z-direction, ΔLz = -0.05 inches

To determine the stress components Ox, Oy, and Oz that cause these deformations, we'll use the following equations:ΔLx = aOx / E (1 - ν)ΔLy = bOy / E (1 - ν)ΔLz = cOz / E (1 - ν)

where, ΔLx, ΔLy, and ΔLz are the changes in the length of the block in the x, y, and z directions, respectively.

ΔLx = 0.06 in.= a

Ox / E (1 - ν)56.06 - 56 = 56

Ox / (29 x 103)(1 - 0.33)

Ox = 2.07 ksi

ΔLy = 0.10 in.= b

Oy / E (1 - ν)56.10 - 56 = 56

Oy / (29 x 103)(1 - 0.33)

Oy = 3.59 ksi

ΔLz = -0.05 in.= c

Oz / E (1 - ν)55.95 - 56 = 56

Oz / (29 x 103)(1 - 0.33)

Oz = -2.06 ksi

Know more about components here:

https://brainly.com/question/31044183

#SPJ11

Daily, monthly, as well as yearly loads connote to the extent of electrical power that is taken in by a system or a region over different time frame.

Daily load means how much electricity is being used at different times of the day, over a 24-hour period. Usually, people use more electricity in the morning and evening when they use appliances and lights.

Monthly load means the total amount of electricity used in a month. This considers changes in how much energy is used each day and includes things like weather, seasons, and how people typically use energy.

Yearly load means the amount of energy used in a whole year. This looks at how much energy people use each month and helps companies plan how much energy they need to make and deliver over a long time.

Read more about based load here:

https://brainly.com/question/1288780

#SPJ4

Answer : Option C

Solution  : Equilibrium cooling of a hyper-eutectoid steel to room temperature will form pro-eutectoid cementite and pearlite. Hence, the correct option is C.

A steel that contains more than 0.8% of carbon by weight is known as hyper-eutectoid steel. Carbon content in such steel is above the eutectoid point (0.8% by weight) and less than 2.11% by weight.

The pearlite is a form of iron-carbon material. The structure of pearlite is lamellar (a very thin plate-like structure) which is made up of alternating layers of ferrite and cementite. A common pearlitic structure is made up of about 88% ferrite by volume and 12% cementite by volume. It is produced by slow cooling of austenite below 727°C on cooling curve at the eutectoid point.

Iron carbide or cementite is an intermetallic compound that is formed from iron (Fe) and carbon (C), with the formula Fe3C. Cementite is a hard and brittle substance that is often found in the form of a lamellar structure with ferrite or pearlite. Cementite has a crystalline structure that is orthorhombic, with a space group of Pnma.

Know more about cooling here:

https://brainly.com/question/32239921

#SPJ11