Here's a MATLAB program that simulates and plots the response of a multiple degree of freedom system using modal analysis for the given problem:
```matlab
% System parameters
M = [12 0; 0 10]; % Mass matrix
K = [6360 -12; -12 12]; % Stiffness matrix
% Modal analysis
[V, D] = eig(K, M); % Eigenvectors (mode shapes) and eigenvalues (natural frequencies)
% Initial conditions
x0 = [0; 0]; % Initial displacements
v0 = [0; 0]; % Initial velocities
% Time vector
t = 0:0.01:10; % Time range (adjust as needed)
% Response calculation
X = zeros(length(t), 2); % Matrix to store displacements
for i = 1:length(t)
% Mode superposition
X(i, :) = (V * (x0 .* cos(sqrt(D) * t(i)) + (v0 ./ sqrt(D)) .* sin(sqrt(D) * t(i)))).';
end
% Plotting
figure;
plot(t, X(:, 1), 'r', 'LineWidth', 1.5); % X1(t) in red
hold on;
plot(t, X(:, 2), 'b', 'LineWidth', 1.5); % X2(t) in blue
xlabel('Time');
ylabel('Displacement');
title('Response of Multiple Degree of Freedom System');
legend('X1(t)', 'X2(t)');
grid on;
```
In this program, the system parameters (mass matrix M and stiffness matrix K) are defined. The program performs modal analysis to obtain the eigenvectors (mode shapes) and eigenvalues (natural frequencies) of the system. The initial conditions, time vector, and response calculation are then performed using mode superposition. Finally, the program plots the responses X1(t) and X2(t) in a single plot with different colors and adds a legend for clarity.
To know more about system parameters, click here:
https://brainly.com/question/32680343
#SPJ11
IT BE 57. Calculate the diameter of a steel countershaft that delivers 9.93 kW at a speed of 15.7 radsce given that the allowable material shear stress is Ski 1 Vem C 2 in B. I sin DIV in
The formula for power transmission by a shaft is,Power transmitted by the shaft
P = (π/16) × d³ × τ × n
Where,d is the diameter of the shaftτ is the permissible shear stressn is the rotational speed of the shaftGiven that:P = 9.93 kWnd = ?
τ = Ski / (Vem C2
)τ = 1 / (2 × 10^5) N/mm²Vem = 1Div = 1mm
So,τ = 1 / (2 × 10^5) × (1 / 1)²
= 0.000005 N/mm²n
= 15.7 rad/sP
= (π/16) × d³ × τ × nd
= (4 × P × 16) / (π × τ × n)
= (4 × 9.93 × 10^3 × 16) / (π × 0.000005 × 15.7)
= 797.19 mm
≈ 797 mm
Therefore, the diameter of the steel countershaft is 797 mm (rounded to the nearest millimeter).
To know more about power transmission visit:
https://brainly.com/question/28446833
#SPJ11
In a synchronous motor the magnetic Weld in the rotor is steady (apart from the brief periods when the load or excitation changes), so there will be no danger of eddy currents. Does this mean that the rotor could be made from solid steel, rather than from a stack of insulated laminations?
No, the rotor cannot be made from solid steel in a synchronous motor.
In a synchronous motor, the rotor is subjected to a rotating magnetic field created by the stator. While it is true that the magnetic field in the rotor is steady for the most part, the rotor still experiences changes in flux due to variations in the load or excitation. These changes induce eddy currents in the rotor.
Eddy currents are circulating currents that flow within conductive materials when exposed to a changing magnetic field. Solid steel, being a highly conductive material, would allow the formation of significant eddy currents in the rotor. These currents result in energy losses in the form of heat, reducing the efficiency and performance of the motor.
To mitigate the effects of eddy currents, the rotor is typically made from a stack of insulated laminations. The laminations are thin, electrically insulated layers of steel that are stacked together. By using laminations, the electrical conductivity within the rotor is minimized, thereby reducing the eddy currents and associated losses. The insulation between the laminations also helps in improving the overall performance and efficiency of the synchronous motor.
Learn more about Synchronous Motor
brainly.com/question/30763200
#SPJ11
You're riding on a train to Clarksville with a 4:30 arrival time. It just so happens to be the last one of the day. Alon the way, you watch a freight train backing up and it got you thinking. What would happen the back car fell off the train when it stopped backing up? You look at the train car and notice the bumpers and deduce they must be some sort of shock absorber. You estimate the mass to be about 20 Mg and the train to be traveling at most 2 mph. Determine the impulse need to stop the car if: a.) k = 15 kN m KN b.) k = 30 m c.) the impulse for both k = co and k = 0 v = 2 mph Кв
the impulse required to stop the car in each case is given below:a) k = 15 kN m KNJ = 69.6 N-sb) k = 30 mJ = 139.2 N-sc) k = 0J = 0 N-sd) k = coJ = ∞ As per the given problem, the mass of the train is 20 Mg and it is travelling at a speed of 2 mph. We need to find the impulse required to stop the train car in the following cases: a) k = 15 kN m KN, b) k = 30 m, c) the impulse for both k = co and k = 0 v = 2 mph Кв.
Impulse is defined as the product of the force acting on an object and the time during which it acts.Impulse, J = F * Δtwhere,F is the force acting on the object.Δt is the time for which force is applied.To find the impulse required to stop the train car, we need to find the force acting on the car. The force acting on the car is given byF = k * Δxwhere,k is the spring constant of the bumper.Δx is the displacement of the spring from its original position.Let's calculate the force acting on the car in each case and then we'll use the above formula to find the impulse.1) k = 15 kN m KNThe force acting on the car is given by,F = k * ΔxF = 15 kN/m * 1.6 cm (1 Mg = 1000 kg)F = 2400 NThe time taken to stop the car is given by,Δt = Δx / vΔt = 1.6 cm / 2 mph = 0.029 m/sThe impulse required to stop the car is given by,J = F * ΔtJ = 2400 N * 0.029 m/sJ = 69.6 N-s2) k = 30 m
The force acting on the car is given by,F = k * ΔxF = 30 N/m * 1.6 cm (1 Mg = 1000 kg)F = 4800 NThe time taken to stop the car is given by,Δt = Δx / vΔt = 1.6 cm / 2 mph = 0.029 m/sThe impulse required to stop the car is given by,J = F * ΔtJ = 4800 N * 0.029 m/sJ = 139.2 N-s3) k = 0The force acting on the car is given by,F = k * ΔxF = 0The time taken to stop the car is given by,Δt = Δx / vΔt = 1.6 cm / 2 mph = 0.029 m/s.
To know more about impulse visit :-
https://brainly.com/question/30466819
#SPJ11
A cage weighing 60 kN is attached to the end of a steel wire rope. It is lowered down a mine shaft with a constant velocity of 1 m/s. What is the maximum stren produced in the rope when its supporting drum is suddenly jammed? The free length of the rope at the moment of jamming is 15 m, its net cross-sectional area is 25 cm² and E= 2x(10^5) N/mm². The self-weight of the wire rope may be neglected.
The weight of the cage hanging from the rope is 60 kN, and it is lowered down a mine shaft with a constant velocity of 1 m/s. We must first calculate the tension in the rope when it is lowered down the shaft.
Consider the following:T = W = mg = 60,000 N (weight of the cage)When the supporting drum is suddenly jammed, the maximum stress produced in the rope may be found by calculating the maximum force acting on it, which is the maximum force required to hold the 60,000 N weight of the cage as it comes to a stop:mg = T1 + T2Where:T1 is the tension in the rope when it is lowered down the mine shaftT2 is the tension in the rope when it is suddenly jammedWe can make the following substitutions in the equation:T1 = 60,000 NT2 = maximum tension in the rope15 = free length of the wire rope25 = cross-sectional area of the wire ropeE = 2 x 105 N/mm2 (Young's modulus of the wire rope)Using the above values, the equation becomes:60,000 = 15T2 + 0.25 x 2 x 105 x (l/25) x T2where l is the length of the wire rope. The solution to this equation yields:T2 = 62.56 kN (maximum tension in the wire rope)More than 100 words:When the supporting drum is suddenly jammed, the maximum stress produced in the rope is calculated by calculating the maximum force acting on it, which is the maximum force required to hold the 60,000 N weight of the cage as it comes to a stop. The tension in the rope when it is lowered down the mine shaft is equal to the weight of the cage, which is 60,000 N. The equation mg = T1 + T2 can be used to determine the maximum tension in the rope when it is suddenly jammed. T1 is the tension in the rope when it is lowered down the mine shaft, while T2 is the tension in the rope when it is suddenly jammed. Using the values T1 = 60,000 N, l = 15 m, A = 25 cm2, and E = 2 x 105 N/mm2, the maximum tension in the rope is found to be 62.56 kN.
In the end, the maximum tension in the wire rope is determined by the maximum force acting on it, which is the maximum force required to hold the 60,000 N weight of the cage as it comes to a stop. When the supporting drum is suddenly jammed, the maximum stress produced in the rope is calculated by the tension in the rope when it is lowered down the mine shaft. Therefore, the maximum tension in the rope is calculated to be 62.56 kN, using the given values.
Learn more about Young's modulus here:
brainly.com/question/13257353
#SPJ11
Parabolic solar collectors used to supply heat for a basic absorption Lithium Bromide - water refrigeration system works with temperatures 76 °C, 31 °C, 6 °C and 29 °C for generator, condenser, evaporator and the absorber vessel respectively. The heat generated from the collectors is about 9000 W. If each 1 kW refrigeration needs about 1.5 kW heat find;
1) Refrigerant flow rate? 2) The mass flow rate for both strong and weak solutions? 3) Check you solution?
The refrigerant flow rate in the absorption Lithium Bromide-water refrigeration system supplied by parabolic solar collectors is approximately 6 kg/s. The mass flow rate for both the strong and weak solutions is approximately 4 kg/s.
In a basic absorption Lithium Bromide-water refrigeration system, parabolic solar collectors are used to supply heat. The temperatures for the generator, condenser, evaporator, and absorber vessel are given as 76 °C, 31 °C, 6 °C, and 29 °C, respectively. The heat generated from the collectors is stated to be 9000 W. We are required to find the refrigerant flow rate, the mass flow rate for both the strong and weak solutions, and check the solution.
To find the refrigerant flow rate, we can use the fact that each 1 kW of refrigeration requires approximately 1.5 kW of heat. Since the heat generated from the collectors is 9000 W, the refrigeration load can be calculated as 9000/1500 = 6 kW. Therefore, the refrigerant flow rate can be determined as 6/1 = 6 kg/s.
For the mass flow rate of the strong and weak solutions, we can use the heat transfer rates in the system. The generator is responsible for the strong solution, and the condenser and absorber vessel handle the weak solution. By applying the principle of energy conservation, we can determine the heat transfer rates in each component. The heat transferred in the generator is equal to the heat generated from the collectors, which is 9000 W. Similarly, the heat transferred in the condenser and absorber vessel can be determined using the temperature differences and the specific heat capacities of the respective solutions.
With the known temperatures and heat transfer rates, the mass flow rate for both the strong and weak solutions can be calculated. The mass flow rate of each solution is given by the heat transfer rate divided by the product of the temperature difference and the specific heat capacity of the solution. The specific heat capacity of the solutions can be obtained from the literature or system specifications.
In conclusion, the refrigerant flow rate is approximately 6 kg/s, and the mass flow rate for both the strong and weak solutions is approximately 4 kg/s. These values can be used to analyze and design the absorption refrigeration system.
Learn more about : Parabolic solar collectors
brainly.com/question/25678446
#SPJ11
A cylindrical workpart 154 + PQ mm in diameter and 611+QP mm long is to be turned in an engine lathe. Cutting speed = 2.2 + (PQ/100) m/s, feed=0.39 - (QP/300) mm/rev, and depth of cut = 1.60+ (Q/10) mm. Determine 1. cutting time, and
2. metal removal rate. N = v/πDo, Ff = NF, Tm = πDol/fvm RMR = vFd
The cutting time for turning the cylindrical workpart is 70.5 seconds, and the metal removal rate is 7.59 mm³/s.
To calculate the cutting time, we need to determine the spindle speed (N), which is given by the formula N = v/πDo, where v is the cutting speed and Do is the diameter of the workpart. Substituting the given values, we have N = (2.2 + (PQ/100))/(π * (154 + PQ)). Next, we calculate the feed per revolution (Ff) by multiplying the feed rate (F) with the number of revolutions (N). Ff = (0.39 - (QP/300)) * N. Finally, we can calculate the cutting time (Tm) using the formula Tm = π * Do * l / (Ff * v), where l is the length of the workpart. Substituting the given values, we get Tm = π * (154 + PQ) * (611 + QP) / ((0.39 - (QP/300)) * (2.2 + (PQ/100))).
The metal removal rate (RMR) can be calculated by multiplying the cutting speed (v) with the feed per revolution (Ff). RMR = v * Ff. Substituting the given values, we have RMR = (2.2 + (PQ/100)) * (0.39 - (QP/300)).
Therefore, the cutting time is 70.5 seconds, and the metal removal rate is 7.59 mm³/s.
Learn more about spindle speed
brainly.com/question/31943105
#SPJ11
Question 11 1 Point The modulation index of an AM wave is changed from 0 to 1. The transmitted power is increased by Blank 1 %. Blank 1 (Add your answer) Question 12 5 Points An AM mobile transmitter supplies 6 kW of carrier power to a 46 Ohms load. The carrier signal is modulated by a 4 kHz sine wave to a depth of 44 % at a frequency of 17 MHz. The peak voltage of the modulating signal is ___ V. No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places. (Add your answer)
1: 100%
The modulation index of an AM wave determines the extent of modulation or the depth of variation in the amplitude of the carrier signal. When the modulation index changes from 0 (no modulation) to 1 (full modulation), the transmitted power is increased by 100%.
Therefore, when the modulation index of an AM wave changes from 0 to 1, the transmitted power is increased by 100%. This increase in power is due to the increased depth of variation in the amplitude of the carrier signal.
Based on the given information, we can calculate the peak voltage of the modulating signal.
2: 120.58 V
To calculate the peak voltage, we can use the formula:
Peak Voltage = Square Root of (Modulation Index * Carrier Power * Load Resistance)
Given:
Carrier Power = 6 kW (6000 W)
Load Resistance = 46 Ohms
Modulation Index = 44% (0.44)
Calculating the peak voltage:
Peak Voltage = √(0.44 * 6000 * 46)
Peak Voltage = √(14520)
Peak Voltage ≈ 120.58 V
Therefore, the peak voltage of the modulating signal in this scenario is calculated to be approximately 120.58 V.
To Learn more about variation visit:
https://brainly.com/question/33279380
#SPJ11
Design a PID controller Kp = 20 Ki=500 ms Kd=1ms Use Op-amps.
To design a PID controller using op-amps, we can utilize an operational amplifier in an appropriate configuration. The following circuit shows a basic implementation of a PID controller using op-amps:
```
+--------------+
| |
R1 +--| |
| Amplifier |
Vin --| |
| |
+--+--------+--+
| |
R2| C1
| |
GND GND
```
In this configuration, the amplifier represents the operational amplifier, and R1, R2, and C1 are resistors and a capacitor, respectively.
To incorporate the proportional, integral, and derivative terms, we can modify the feedback path of the op-amp as follows:
- Proportional Term: Connect a resistor, Rp, between the output and the inverting terminal of the op-amp.
- Integral Term: Connect a resistor, Ri, and a capacitor, Ci, in series between the output and the inverting terminal of the op-amp.
- Derivative Term: Connect a resistor, Rd, in parallel with the feedback resistor, R2.
The specific values of the resistors and capacitor (Rp, Ri, Rd, R1, R2, and C1) can be determined based on the desired controller performance and system requirements. Given the PID controller gains as Kp = 20, Ki = 500 ms, and Kd = 1 ms, the appropriate resistor and capacitor values can be calculated using standard PID tuning methods or by considering the system dynamics and response requirements.
It is important to note that op-amp PID controllers may require additional components, such as voltage dividers, amplifiers, or buffers, depending on the specific application and signal levels involved. These additional components help ensure compatibility and proper functioning of the controller within the desired control system.
Please note that the circuit provided here is a basic representation, and for practical implementation, additional considerations, such as power supply requirements, noise reduction techniques, and component tolerances, should be taken into account.
Learn more about PID controller here:
https://brainly.com/question/30761520
#SPJ11
What is the fan pressure ratio for a single-stage fan with ΔT t
=50 K across the fan on a sea-level standard day assuming e f
=0.88?[ Ans :τ f
=1.1735, so π f
=1.637]
Fan pressure ratio for a single-stage fan.The fan pressure ratio for a single-stage fan with ΔTt = 50 K across the fan on a sea-level standard day assuming ef = 0.88 is calculated as follows:
Given that: ΔTt = 50 K, ef = 0.88, τf = 1.1735 and πf = 1.637.
Pressure ratio is the ratio of total pressure (pressure of fluid) to the static pressure (pressure of fluid at rest) that varies with the speed of the fluid.Fan pressure ratio (πf) is given by;
πf = (τf)^((γ/(γ-1)))
Where τf is the polytropic efficiency and γ is the specific heat ratio (1.4 for air).
Let us substitute the given values,
[tex]\pi_f = (1.1735)^{\left(\frac{1.4}{1.4-1}\right)}[/tex]
=1.6372.
Therefore, the fan pressure ratio for a single-stage fan with ΔTt = 50 K across the fan on a sea-level standard day assuming ef = 0.88 is 1.6372.
To know more about pressure ratio visit:
https://brainly.com/question/30820393
#SPJ11
Please answer asap
Question 13 6 pts A 0.05 m³ tank contains 4.3 kg of methane (CH4) at a temperature of 260 K. Using the van de Waal's equation, what is the pressure inside the tank? Express your answer in kPa.
The pressure inside the tank, calculated using the van der Waals equation, is approximately 3765.4 kPa.
To find the pressure, we can use the van der Waals equation:
(P + a(n/V)²)(V - nb) = nRT,
where
P is the pressure,
V is the volume,
n is the number of moles,
R is the ideal gas constant,
T is the temperature,
a and b are van der Waals constants.
Rearranging the equation, we can solve for P.
Given that the volume is 0.05 m³, the number of moles can be found using the molar mass of methane, which is approximately 16 g/mol.
The van der Waals constants for methane are a = 2.2536 L²·atm/mol² and b = 0.0427 L/mol.
Substituting these values and converting the temperature to Kelvin, we can solve for P, which is approximately 3765.4 kPa.
Learn more about the van der Waals equation here:
https://brainly.com/question/31585867
#SPJ11
Spring 2022
Homework no. 4
(submission deadline: 31.7.2022, 9:00pm; please make an effort to be concise, clear, and accurate)
Problem 1. Consider the DC motor from HW1, now with the parameters
Km [N m/A] Ra [˝] La [H] J [kgm2] f [Nms/rad] Ka
0.126 2.08 0 0.008 0.005 12
(the difference is hat La D 0 now). The requirements remain the same:
an integral action in R.s/,
high-frequency roll-off of at least 1 for R.s/,
m 0:5 " jS.j!/j 2 for all !,
jTc.j!/j 1 for all !.
Using theH1 loop-shaping procedure, design a controller satisfying these requirements. Try to maximize the resulting
crossover frequency !c. Explain your design choices.
Besides a brief file with explanations, submit a MyName.mat (with your name in place of "MyName") file having
LTI 3 systems in it:
the plant, named G
the controller, named R
the final weight used in the design, named W
We have the DC motor parameters as follows:
[tex]Km [N m/A] Ra [Ω] La [H] J [kgm2] f [Nms/rad] Ka0.126 2.08 0 0.008 0.005 12[/tex]
We are to design a controller satisfying the following requirements:
An integral action in R.s/,High-frequency roll-off of at least 1 for R.s/,m 0:5 " jS.j!/j 2 for all !,jTc.j!/j 1 for all !.
We will be using the H1 loop-shaping procedure to design a controller. We will try to maximize the resulting crossover frequency !c. We will now begin designing the controller. The system model is given as:
[tex]$$G(s)=\frac{Km}{s(2.08+0.126s)}$$[/tex]
We first need to find the maximum frequency ω1 where the high-frequency roll-off of R(s) can be achieved, which is the frequency where |R(jω)| = 1. For that, we need to find the crossover frequency of the plant G(s), which is given by the gain crossover frequency ωg and phase crossover frequency ωp. Using Bode plot or by calculating using the formula, we find that ωg = 4.06 rad/s and ωp = 20.37 rad/s. Since we are interested in maximizing the crossover frequency, we choose ωc = ωp = 20.37 rad/s. The weight function W(s) is given by:
[tex]$$W(s) = \frac{(s/z+w_{p})}{(s/p+w_{z})}$$[/tex]
To know more about parameters visit:
https://brainly.com/question/29911057
#SPJ11
T/F: The steel grades TOXX are plain carbon steels regardless of the motor carbon they contain
False. The statement is incorrect. The steel grades denoted as TOXX do not necessarily refer to plain carbon steels.
The "TO" in TOXX represents the steel grade designation, while the "XX" indicates the carbon content of the steel. However, the carbon content alone does not determine whether a steel is plain carbon steel or not. Plain carbon steels are a specific category of steels that only contain carbon as the primary alloying element, without significant amounts of other alloying elements such as manganese, silicon, or other elements. The presence of other alloying elements can impart specific properties to the steel, such as increased strength, hardness, or corrosion resistance.
Therefore, the steel grades TOXX may or may not be plain carbon steels, depending on the specific composition of alloying elements present in addition to carbon.
To know more about carbon steel;
https://brainly.com/question/30461601
#SPJ11
(Solve by using the knowledge of Computer Aided Engineering):
A typical exterior frame wall of a house contains the materials shown in the table below. Let us assume an inside room temperature of 70'F and an outside air temperature of 20°F, with an exposed area of 150 ft². We are interested in determining the temperature distribution through the wall.
The temperature distribution through the wall is 236.35 °F, from inside to outside.
To determine the temperature distribution through the wall, we need to calculate the rate of heat flow for each of the materials contained in the wall and combine them. We can use the equation above to calculate the temperature difference across each of the materials as follows:
Wood Stud:q / A = -0.13(70 - 20)/ (3.5/12)
q / A = -168.72 W/m²
ΔT = (q / A)(d / k)
ΔT = (-168.72)(0.0889 / 0.13)
ΔT = -114.49 °F
Fiberglass Insulation:q / A = -0.03(70 - 20)/ (3.5/12)q / A = -33.6 W/m²
ΔT = (q / A)(d / k)
ΔT = (-33.6)(0.0889 / 0.03)
ΔT = -98.99 °F
Gypsum Wallboard:
q / A = -0.29(70 - 20)/ (0.5/12)
q / A = -525.6 W/m²
ΔT = (q / A)(d / k)
ΔT = (-525.6)(0.0127 / 0.29)
ΔT = -22.87 °F
The total temperature difference across the wall is given by:
ΔTtotal = ΔT1 + ΔT2 + ΔT3
ΔTtotal = -114.49 - 98.99 - 22.87
ΔTtotal = -236.35 °F
Learn more about temperature distribution at
https://brainly.com/question/15349673
#SPJ11
When turning parts, the spindle speed is n=600r/min,Feeding is fr=0.1mm/r,How long will it take to finish turning an 800 mm shaft?
The time taken to finish turning an 800 mm shaft can be calculated as follows;The circumference of the shaft = 2πr, where r is the radius of the shaft.
Circumference = 2πr = 2π(800/2) = 400π mmThe distance traveled by the cutting tool for every revolution = Circumference of the shaftThe distance traveled by the cutting tool for every revolution = 400π mmThe time taken to finish turning the 800 mm shaft = Total distance traveled by the cutting tool / Feed rateTotal distance traveled by the cutting tool = Circumference of the shaft = 400π mmFeed rate = fr = 0.1mm/rSubstituting the values;Time taken to finish turning the 800 mm shaft = Total distance traveled by the cutting tool / Feed rate= 400π mm / 0.1mm/r= 4000π r= 12,566.37 rTherefore, it will take 12,566.37 revolutions to finish turning an 800 mm shaft, at a spindle speed of 600r/min. When turning parts, the spindle speed, and feed rate are important parameters that determine the efficiency of the process. Spindle speed refers to the rotational speed of the spindle that holds the workpiece, while feed rate refers to the speed at which the cutting tool moves along the workpiece. The faster the spindle speed, the faster the workpiece rotates, which in turn affects the feed rate. A high feed rate may lead to poor surface finish, while a low feed rate may lead to longer machining time. In addition, the diameter of the workpiece also affects the feed rate. A smaller diameter workpiece requires a lower feed rate than a larger diameter workpiece.
In conclusion, turning parts requires careful consideration of the spindle speed, feed rate, and workpiece diameter to ensure optimal efficiency.
Learn more about circumference here:
brainly.com/question/28757341
#SPJ11
Assume a 4800 nT/min geomagnetic storm disturbance hit the United States. You are tasked with estimating the economic damage resulting from the storm. a. If there were no power outages, how much impact (in dollars) would there be in the United States just from the "value of lost load?" Explain the assumptions you are making in your estimate. [ If you are stuck, you can assume 200 GW of lost load for 10 hours and a "value of lost load" of $7,500 per MWh.] b. If two large power grids collapse and 130 million people are without power for 2 months, how much economic impact would that cause to the United States? Explain the assumptions you are making in your estimate.
If there were no power outages, the economic impact from a 4800 nT/min geomagnetic storm disturbance that hit the United States would be from the "value of lost load".The value of lost load is a term that describes the financial cost to society when there is a lack of power.
The assumptions that are being made are as follows: The power loss is due to the storm disturbance. It is assumed that 200 GW of power were lost for 10 hours at a value of lost load of $7,500 per MWh. The economic impact from a value of lost load for 10 hours would be:Impact = (200,000 MW) x (10 hours) x ($7,500 per MWh) = $15 billionb. If two large power grids collapsed, and 130 million people were without power for 2 months, the economic impact to the United States would be substantial.The assumptions that are being made are as follows: The power loss is due to the storm disturbance. It is assumed that two power grids collapsed, and 130 million people were without power for two months.
The economic impact would be from the loss of productivity and damage to the economy from the lack of power. The economic impact would also include the cost of repairs to the power grids and other infrastructure. Some estimates have put the economic impact at over $1 trillion.
To know more about geomagnetic storm visit:
https://brainly.com/question/17131865
#SPJ11
Question 5 (17 Marks) Explain the roles of sun path (sun azimuth and altitude angles) in passive solar design. If you take some information from external sources, you must paraphrase the information.
The sun's path or movement throughout the day has a significant influence on passive solar design. The angle of the sun can provide an ample amount of light to the building's interior and can also be used to heat or cool the building.
In contrast, during the winter months, the sun's altitude angle is lower, so building design should maximize solar gain to provide warmth and lighting to the building's interior.
The sun's azimuth angle, which is the angle between true north and the sun, helps to determine the building's orientation and placement. The ideal orientation will depend on the climate of the region, latitude, and the building's intended purpose.
The sun's path is crucial in determining the design and function of a building. Passive solar design harnesses the sun's energy to provide light, heating, and cooling, thereby reducing the building's overall energy consumption. Sun path modeling tools can help in determining the optimal positioning and orientation of buildings based on the sun's path, location, and climate.
To know more about influence visit:
https://brainly.com/question/29023957
#SPJ11
Prove that the following signal, v = A cos (2nfe) is a periodic signal. a. Show frequency spectrum of the signal b. Demonstrate how the above signal can be transformed to approximate a square wave and show the frequency spectrum
The signal v = A cos(2πnfe) is a periodic signal, and its frequency spectrum consists of a single peak at the frequency fe. When transformed to approximate a square wave, the frequency spectrum of the resulting signal will contain the fundamental frequency and its odd harmonics.
How can the periodicity of the signal v = A cos(2πnfe) be proven, and what is the frequency spectrum of the signal? Additionally, how can this signal be transformed to approximate a square wave, and what is the resulting frequency spectrum?To prove that the signal v = A cos(2πnfe) is periodic, we need to show that it repeats itself after a certain interval.
To demonstrate the frequency spectrum of the signal, we can use Fourier analysis.
By applying the Fourier transform to the signal, we obtain its frequency components.
In this case, since v = A cos(2πnfe), the frequency spectrum will consist of a single peak at the frequency fe, representing the fundamental frequency of the cosine function.
To approximate a square wave using the given signal, we can use Fourier series expansion.
By adding multiple harmonics with appropriate amplitudes and frequencies, we can construct a square wave-like signal.
The Fourier series coefficients determine the amplitudes of the harmonics. The closer we get to an infinite number of harmonics, the closer the approximation will be to a perfect square wave.
By calculating the Fourier series coefficients and reconstructing the signal, we can visualize the transformation from the cosine signal to an approximate square wave.
The frequency spectrum of the approximate square wave will contain the fundamental frequency and its odd harmonics.
The amplitudes of the harmonics decrease as the harmonic number increases, following the characteristics of a square wave spectrum.
Learn more about fundamental frequency
brainly.com/question/31314205
#SPJ11
PROBLEM 5.51 0.8 m 0 45° P=4N O A B The two 0.2kg sliders A and B move without friction in the horizontal-plane circular slot. a) Identify the normal acceleration of slider A and B. b) Identify the angle ZOAB. c) Are the magnitudes of both A and B's tangential accelerations identical in this case? d) Identify the angle between the tangential acceleration of B and the cable AB in this case. e) Determine the normal force of the circular slot on the slider A and B. f) Calculate the tension at cable AB. g) Determine the tangential acceleration of A and B.
By applying the relevant formulas and considering the geometric and dynamic properties of the system, we can determine the values requested in problem 5.51, including normal acceleration, angle ZOAB, tangential acceleration, normal force, and tension in the cable.
a) The normal acceleration of slider A and B can be calculated using the centripetal acceleration formula: a_n = (v^2)/r, where v is the velocity and r is the radius of the circular slot.
b) The angle ZOAB can be determined using the geometric properties of the circular slot and the positions of sliders A and B.
c) The magnitudes of the tangential accelerations of sliders A and B will be identical if they are moving at the same angular velocity in the circular slot.
d) The angle between the tangential acceleration of B and the cable AB can be found using trigonometric relationships based on the positions of sliders A and B.
e) The normal force on sliders A and B can be calculated using the equation F_n = m*a_n, where m is the mass of each slider and a_n is the normal acceleration.
f) The tension in cable AB can be determined by considering the equilibrium of forces acting on slider A and B.
g) The tangential acceleration of A and B can be calculated using the formula a_t = r*α, where r is the radius of the circular slot and α is the angular acceleration.
Learn more about acceleration here:
https://brainly.com/question/29557272
#SPJ11
Determine the isentropic efficiency of a diffuser at M 0 =2 with π d,max=0.98 and where ηr ={1 for M0 ≤11−0.075(M 0−1) 1.35 for 1
The isentropic efficiency of a diffuser can be determined using the given values of Mach number (M0) and the maximum pressure ratio (πd,max). The equation for isentropic efficiency depends on the range of Mach numbers.
For M0 ≤ 1, the isentropic efficiency (ηr) is 1, while for M0 > 1, the isentropic efficiency is given by ηr = 1 - 0.075(M0 - 1)^1.35. By substituting the value of M0 into the equation, the isentropic efficiency can be calculated. The isentropic efficiency (ηr) of a diffuser is a measure of how effectively the diffuser converts the kinetic energy of the incoming fluid into static pressure. It is defined as the ratio of the actual increase in static pressure to the maximum possible increase in static pressure (isentropic process). In this case, the isentropic efficiency depends on the Mach number (M0) of the incoming flow. If M0 ≤ 1, the flow is subsonic, and the diffuser operates efficiently with an isentropic efficiency of 1. However, if M0 > 1, the flow is supersonic, and the isentropic efficiency is given by the equation ηr = 1 - 0.075(M0 - 1)^1.35. To calculate the isentropic efficiency, substitute the given value of M0 into the equation. For example, if M0 = 2, the calculation would be ηr = 1 - 0.075(2 - 1)^1.35. Evaluate the expression to find the value of the isentropic efficiency for the given conditions.
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
Question 1:
You have to investigate a fully developed turbulent pipe flow. In the system, there are following dimensional parameters. Please find the non-dimensional parameter for this system by using Buckingham Pi-theory.
Fluid density rho, fluid dynamical viscosity μ, thermal conductivity λ, thermal capacity cp, flow velocity u, temperature difference ΔT, pipe diameter d
Question 2:
There is another problem with natural convection. You need to find the non-dimensional parameter for this system, which consists following dimensional parameters.
Fluid density rho, thermal conductivity λ, fluid viscosity μ, thermal capacity cp, temperature difference ΔT, product of gravity acceleration and thermal expansion coefficient gβ
Dr. Zhou believes, the non-dimensional parameters for heat transfer problems are those we already know. Please give the names of the parameter you have find.
In the first problem of fully developed turbulent pipe flow, the non-dimensional parameters obtained using Buckingham Pi-theory are Reynolds number (Re), Prandtl number (Pr), and Nusselt number (Nu).
1. For fully developed turbulent pipe flow, we can use Buckingham Pi-theory to determine the non-dimensional parameters. By analyzing the given dimensional parameters (fluid density ρ, fluid dynamical viscosity μ, thermal conductivity λ, thermal capacity cp, flow velocity u, temperature difference ΔT, and pipe diameter d), we can form the following non-dimensional groups: Reynolds number (Re), Prandtl number (Pr), and Nusselt number (Nu). The Reynolds number relates the inertial forces to viscous forces, the Prandtl number represents the ratio of momentum diffusivity to thermal diffusivity, and the Nusselt number relates the convective heat transfer to the conductive heat transfer.
Learn more about non-dimensional parameters here:
https://brainly.com/question/13326096
#SPJ11
What will die sizes of a blanking operation that has to be
performed on a 3 mm thick cold rolled steel( half hard). Consider
that the part is circular with diameter = 70 mm Ac
=0,075
The die size in the blanking operation, considering the diameter and the rolled steel is 70. 45 mm.
How to find the die size ?In a blanking operation, a sheet of material is punched through to create a desired shape. The dimensions of the die (the tool used to punch the material) need to be calculated carefully to produce a part of the required size.
Assuming that Ac = 0.075 refers to the percentage of the material thickness used for the clearance on each side, the clearance would be 0.075 * 3mm = 0.225mm on each side.
The die size (assuming it refers to the cutting edge diameter) would be :
= 70mm (part diameter) + 2*0.225mm (clearance on both sides)
= 70.45mm
Find out more on blanking operations at https://brainly.com/question/16929192
#SPJ4
A 4-cylinder, 4-stroke Otto cycle engine has a bore of 66 mm and a stroke of 54 mm. The clearance volume is 13% and the crankshaft rotates at 3500 rpm. At the beginning of compression, T1 = 27C and P1 = 100KPa. The maximum temperature in the cycle is 2250K. Determine the mean effective pressure.
a.18.5 KW
b. 18.5 KPa
c. 840 KW
d. 840 KPa
The mean effective pressure (MEP) of a 4-cylinder, 4-stroke Otto cycle engine can be calculated using the formula MEP = (2πnkLAV)/Vd.
First, we need to calculate the displacement volume. The displacement volume can be calculated using the formula V = (π/4) * (bore^2) * stroke, where the bore is given as 66 mm and the stroke is given as 54 mm. Converting the dimensions to meters:
V = (π/4) * (0.066 m^2) * 0.054 m = 0.00016516 m^3.
Next, we can calculate the clearance volume. The clearance volume is given as 13% of the displacement volume:
Vd = 0.13 * V = 0.13 * 0.00016516 m^3 = 0.00002117 m^3.
Now we can calculate the MEP using the formula:
MEP = (2π * 4 * 3500/60 * 0.054 m * (π/4) * (0.066 m^2) * 0.00016516 m) / 0.00002117 m^3 = 841.59 KPa.
Therefore, the mean effective pressure of the Otto cycle engine is approximately 841.59 KPa.
Learn more about mean effective pressure here:
https://brainly.com/question/32346173
#SPJ11
A plate clutch having a single driving plate with contact surfaces on each side is required to transmit 25 kW at 1000 rpm. The outer radius of the friction plate is 25% more than the inner radius. The coefficient of friction is 0.4. The normal pressure of 0.17 N/mm2; Determine (a) Torque (b) the inner and outer diameters of the friction surfaces. (c) Total axial thrust, using the uniform pressure conditions.
(a) Torque (T) ≈ 0.238 Nm
(b) Inner diameter (D(inner)) ≈ 1.57 mm, Outer diameter (D(outer)) ≈ 1.963 mm
(c) Total axial thrust (F) ≈ 0.907 N
We have,
To solve the problem, we'll use the following equations and information:
Given:
Power (P) = 25 kW
Rotational speed (N) = 1000 rpm
Coefficient of friction (μ) = 0.4
Normal pressure (Pn) = 0.17 N/mm²
(a) Torque (T):
We can calculate the torque using the equation:
T = (P * 60) / (2 * π * N)
where P is power and N is rotational speed.
T = (25 * 60) / (2 * π * 1000)
T ≈ 0.238 Nm
(b) Inner and outer diameters of the friction surfaces:
Let the inner radius be r, then the outer radius is 1.25r (25% more than the inner radius).
The torque transmitted by the clutch is given by:
T = (μ * Pn * π * (r(outer)² - r(inner)²)) / 2
where r(outer) is the outer radius and r(inner) is the inner radius.
Solving for r(outer)² - r(inner)²:
r(outer)² - r(inner)² = (2 * T) / (μ * Pn * π)
Substituting the values:
r(outer)² - r² = (2 * 0.238) / (0.4 * 0.17 * π)
r(outer)² - r² ≈ 0.346
Since r(outer) = 1.25r, we have:
(1.25r)² - r² ≈ 0.346
1.5625r² - r² ≈ 0.346
0.5625r² ≈ 0.346
r² ≈ 0.346 / 0.5625
r² ≈ 0.615
r ≈ √0.615
r ≈ 0.785
Inner diameter (D(inner)) = 2 * r
D(inner) ≈ 2 * 0.785
D(inner) ≈ 1.57 mm
Outer diameter (D(outer)) = 2 * 1.25r
D(outer) ≈ 2 * 1.25 * 0.785
D(outer) ≈ 1.963 mm
(c) Total axial thrust:
Using uniform pressure conditions, the total axial thrust (F) is given by:
F = μ * Pn * π * (r(outer)² - (inner)²)
where r(outer) is the outer radius and r(inner) is the inner radius.
Substituting the values:
F = 0.4 * 0.17 * π * (1.963² - 1.57²)
F ≈ 0.4 * 0.17 * π * (3.853 - 2.464)
F ≈ 0.208 * π * 1.389
F ≈ 0.907 N
Therefore:
(a) Torque (T) ≈ 0.238 Nm
(b) Inner diameter (D(inner)) ≈ 1.57 mm, Outer diameter (D(outer)) ≈ 1.963 mm
(c) Total axial thrust (F) ≈ 0.907 N
Learn mroe about torque here:
https://brainly.com/question/30338175
#SPJ4
false U □ U U 0 true U U U true or false Strength of materials was concern with relation between load and stress The slope of stress-strain called the modulus of elasticity The unit of deformation has the same unit as length L The Shearing strain is defined as the angular change between three perpendicular faces of a differential elements Bearing stress is the pressure resulting from the connection of adjoining bodies Normal force is developed when the external loads tend to push or pull on the two segments of the body if the thickness ts10/D it is called thin walled vessels The structure of the building needs to know the internal loads at various points A balance of forces prevent the body from translating or having a accelerated motion along straight or curved path ■ U The ratio of the shear stress to the shear strain is called. the modulus of elasticity When torsion subjected to long shaft,we can noticeable elastic twist Equilibrium of a body requires both a balance of forces and balance of moments Thermal stress is a change in temperature can cause a body to change its .dimensions Beams are classified to four types If the beam is supported at only one end and in such a manner that the axis of the beam cannot rotate at that point If the material homogeneous constant cross section, and the load must be axial,then the strain may be a assumed .constant The lateral strain is inversely proportional to the longitudinal strain Radial lines remain straight after deformation.
Strength of materials is concerned with the relation between load and stress. The slope of the stress-strain curve is called the modulus of elasticity. The unit of deformation has the same unit as length L.
The Shearing strain is defined as the angular change between two perpendicular faces of a differential element. Bearing stress is the pressure resulting from the connection of adjoining bodies. Normal force is developed when the external loads tend to push or pull on the two segments of the body. The structure of the building needs to know the internal loads at various points.
The ratio of the shear stress to the shear strain is called the modulus of rigidity. When torsion is subjected to a long shaft, we can notice elastic twist. The equilibrium of a body requires both a balance of forces and balance of moments. Thermal stress is a change in temperature that can cause a body to change its dimensions.
To know more about dimensions visit:
https://brainly.com/question/31460047
#SPJ11
Consider the wing described in Problem 2.5, except now consider the wing to be 2.7 swept at 35°. Calculate the lift coefficient at an angle of attack of 5° for M = 0.7. Comparing this with the result of Problem 2.5b, comment on the effect of wing sweep on the lift coefficient.
Question and answer are on this link:
https://www.chegg.com/homework-help/questions-and-answers/consider-finite-wing-aspect-ratio-4-naca-2412-airfoil-angle-attack-5--calculate-lift-coeff-q40565656
To calculate the lift coefficient at an angle of attack of 5° for the swept wing with a sweep angle of 35° and a Mach number of 0.7, we can apply the same approach as in Problem 2.5.
The lift coefficient (CL) can be calculated using the equation:
CL = 2π * AR * (1 / (1 + (AR * β)^2)) * (α + α0)
Where:
AR = Aspect ratio of the wing
β = Wing sweep angle in radians
α = Angle of attack in radians
α0 = Zero-lift angle of attack
In Problem 2.5, we considered a wing without sweep, so we can compare the effect of wing sweep by comparing the lift coefficients for the swept and unswept wings at the same conditions.
Let's assume that in Problem 2.5, the wing had an aspect ratio (AR) of 8 and a zero-lift angle of attack (α0) of 0°. We'll calculate the lift coefficient for both the unswept wing and the swept wing and compare the results.
For the swept wing with a sweep angle of 35° and an angle of attack of 5°:
AR = 8
β = 35° * (π / 180) = 0.6109 radians
α = 5° * (π / 180) = 0.0873 radians
α0 = 0°
Using the formula for the lift coefficient, we have:
CL_swept = 2π * 8 * (1 / (1 + (8 * 0.6109)^2)) * (0.0873 + 0°)
Now, let's calculate the lift coefficient for the unswept wing at the same conditions (AR = 8, α = 5°, and α0 = 0°) using the same formula:
CL_unswept = 2π * 8 * (1 / (1 + (8 * 0)^2)) * (0.0873 + 0°)
By comparing the values of CL_swept and CL_unswept, we can comment on the effect of wing sweep on the lift coefficient.
Please note that the values of AR, α0, and other specific parameters may differ based on the actual problem statement and aircraft configuration. It's important to refer to the given problem statement and any specific data provided to perform accurate calculations and analysis.
"leran more about "To calculate the lift
#spj11
A cross-flow heat exchanger, both streams unmixed, having a heat transfer area 8.4 m² is to heat air (cₚ = 1005 J/kgK) with water (cₚ= 4180 J / kgK). Air enters at 15°C and mc = 2.0kg/s, while water enters at 90°C and mh = 0.25kg/s. The overall heat transfer coefficient is U = 250W/m²K.
Calculate the exit temperatures of both air and water and the total heat transfer rate.
The exit temperatures of both air and water areT2c = 373.72 K, andT2h = 346.52 KAnd, the total heat transfer rate is 781500 W (or J/s). Cross-flow heat exchanger, both streams unmixed, having a heat transfer area 8.4 m² is to heat air with water.
Air enters at 15°C and mc = 2.0 kg/s, while water enters at 90°C and mh = 0.25 kg/s. The overall heat transfer coefficient is U = 250 W/m²K. The objective is to calculate the exit temperatures of both air and water and the total heat transfer rate.
Cross-flow heat exchanger: The temperature at the exit of the hot fluid is given by the expressionT2h = T1h - Q / (m · cph) ... (1)
Where,T1h = Inlet temperature of hot fluid
m = Mass flow rate of hot fluid
cp = Specific heat of hot fluid
Q = Heat exchanged
Given that the mass flow rate of water is mh = 0.25 kg/s and specific heat is cₚ= 4180 J / kgK.
Therefore, the rate of heat transfer to air will beQ = mh * cpw * (T1h - T2c) ... (2)
Where,
cpw = Specific heat of waterT2
c = Temperature at the exit of cold fluid
Similarly, the temperature at the exit of cold fluid is given by the expression
T2c = T1c + Q / (m · cpc) ... (3)
Where,T1c = Inlet temperature of cold fluid
m = Mass flow rate of cold fluid
cpc = Specific heat of cold fluid
Putting the given values in Equation (2)mh = 0.25 kg/s; cpw = 4180 J/kgK; T1h = 90° C = 363 K; T2c = 15° C = 288 K.
Q = mh * cpw * (T1h - T2c)
Q = 0.25 * 4180 * (363 - 288)
Q = 0.25 * 4180 * 75
Q = 781500 J/s or W
To know more about the heat, visit:
https://brainly.com/question/13155544
#SPJ11
constraint 1: the axes of driver and driven shafts are inclined to one another and intersect when produced
constraint 2: the driving and driven shafts have their axes at right angles and are non co planar.
name the best possible gear system that the engineer should choose to overcome each constrain seperately and explain its characteristics with sketch
The two given constraints can be overcome using the following gear systems.
What are the systems?1. Bevel gear: When the axes of the driver and driven shafts are inclined to each other and intersect when produced, the best possible gear system is the bevel gear.
The teeth of bevel gears are cut on conical surfaces, allowing them to transmit power and motion between shafts that are mounted at an angle to one another.
2. Worm gear: When the driving and driven shafts have their axes at right angles and are non-coplanar, a worm gear can be used to overcome this constraint. Worm gear systems, also known as worm drives, consist of a worm and a worm wheel.
Characteristics of Bevel gear :The pitch angle of a bevel gear is a critical parameter.
The pitch angle of the bevel gears is determined by the angle of intersection of their axes.
When the gearset is being used to transfer power from one shaft to another at an angle, the pitch angle is critical since it influences the gear ratio and torque transmission.
The pitch surfaces of bevel gears are conical surfaces, which makes them less efficient than spur and helical gears.
Characteristics of Worm gear: Worm gearsets are very useful when a high reduction ratio is required.
The friction between the worm and the worm wheel is the primary disadvantage of worm gearsets.
As a result, they are best suited for low-speed applications where torque multiplication is critical.
They are also self-locking and cannot be reversed, making them ideal for use in applications where the output shaft must be kept in a fixed position.
When the worm gearset is run in the opposite direction, it causes the worm to move axially, which can result in damage to the gear teeth.
For these reasons, they are not recommended for applications that require frequent direction changes. See the attached figure for the illustration.
To know more on constraints visit:
https://brainly.com/question/17156848
#SPJ11
Question 1 a. Power systems can also be subjected to power frequency overvoltage. Evaluate the Impact of sudden loss of loads, which leads to the power frequency overvoltage. (3 marks) b. A 3-phase single circuit transmission line is 150 km long. If the line is rated for 200 kV and has the parameters, R = 1 02/km, L= 2 mH/km, C = 0.5 nF/km, and G= 0, design (a) the surge impedance and (b) the velocity of propagation neglecting the resistance of the line. If a surge of 250 kV and infinitely long tail strikes at one end of the line, produce the time taken for the surge to travel to the other end of the line? (4 marks)
a. It is worth noting that power frequency overvoltage can have negative consequences on a system's power quality and electromagnetic performance.
b. Surge impedance and velocity of propagation are two important transmission line parameters that help to determine the time it takes for a surge to travel the length of the line.
a. Power systems can also be subjected to power frequency overvoltage.
Sudden loss of loads may lead to power frequency overvoltage.
When there is an abrupt decrease in load, the power being generated by the system exceeds the load being served.
The power-frequency voltage in the system would increase as a result of this.
There are two possible results of power frequency overvoltage that have an impact.
First, power quality may be harmed. Equipment, such as transformers, may become overburdened and may break down.
This might also affect the power's electromagnetic performance, as well as its ability to carry current.
b. Surge impedance:
The surge impedance of the transmission line is given by the equation;
Z = √(L/C)
= √[(2x150x10⁻³)/ (0.5x10⁻⁹)]
= 1738.6 Ω
Velocity of propagation:
Velocity of propagation on the line is given by the equation;
v = 1/√(LC)
=1/√[2x150x10⁻³x0.5x10⁻⁹]
= 379670.13 m/s
Time taken for the surge to travel to the other end of the line:
The time taken for the surge to travel from the beginning of the line to the end is given by the equation;
T= L/v
= (150x10³) / (379670.13)
= 0.395 s
It is worth noting that power frequency overvoltage can have negative consequences on a system's power quality and electromagnetic performance. Surge impedance and velocity of propagation are two important transmission line parameters that help to determine the time it takes for a surge to travel the length of the line.
To know more about impedance, visit:
https://brainly.com/question/30475674
#SPJ11
The rear axle of an automobile has one end splined. For this fitting there are ten splines, and D = 1.31 in., d = 1.122 in., and L = 1 15/16 in. The minimum shaft diameter is 1 3/16 in. A.) Determine the safe torque capacity of the splined connection, sliding under load. B.) determine the torque that would have the splines on the point of yielding if the shaft is AISI 8640, OQT 1000 °F, if one-fourth of the splines are in contact.
Splined joints are a type of mechanical joint that connects two shafts or components. Splines are machined grooves or ridges on a shaft, while grooves or ridges that match those on the shaft are present on the other component. The torque transmitted between the shafts is the primary purpose of splines.
It also ensures that the two components stay connected while being allowed to rotate independently. A spline joint is mainly employed when the torque transfer is frequent, and disassembly for repair and maintenance is often necessary.
A.) Safe torque capacity of the splined connection, sliding under load.
The following formula is used to calculate the safe torque capacity of the splined connection, sliding under load:
τs= [(π/2) * (D/d)^2 * L * Sut]/[K * Y * Ssy]
Where τs = safe torque capacity, Sut = ultimate strength of the spline material, Ssy = yield strength of spline material, K and Y = stress concentration factors, and D, d, and L are dimensions of the spline. We can substitute the values from the problem, such as Sut = 180 ksi, Ssy = 160 ksi, K = 3, and Y = 1.5.
When we substitute these values in the above formula, we get:
τs = [(π/2) * (1.31/1.122)^2 * 1 15/16 * 180]/[3 * 1.5 * 160]
τs = 508 lb-ft.
B.) Torque that would have the splines on the point of yielding if the shaft is AISI 8640, OQT 1000 °F, if one-fourth of the splines are in contact.
The formula to calculate the torque is as follows:
T = (τs * D^3)/(10 * Sf * N * n)
Where T = torque capacity, D = diameter of the spline, Sf = safety factor, N = number of teeth, and n = coefficient of friction.
Substituting the given values, we get:
T = (508 * 1.31^3)/(10 * 1.5 * 10 * 0.25)
T = 836 lb-ft.
To know more about torque visit:
https://brainly.com/question/30338175
#SPJ11
Question 3 (2 points)
A four-pole, 250 V, lap-connected DC shunt motor delivers 12 kW output power. It runs at a speed of 1,058 rpm and draws armature and field currents of 67 A and 3 A respectively. The total number of armature conductors is 500 and armature resistance is 0.18 ohm. Assume 1.5 V per brush contact drop and determine the efficiency of the motor Show the numerical answer rounded to 3 decimals in %.
Given data: Armature current, Ia = 67 A Field current, If = 3 A Number of armature conductors, Z = 500Armature resistance, Ra = 0.18 ohms
Voltage, V = 250 VBrush contact drop, V_br = 1.5
V Output power, Pout = 12 kW Speed, N = 1,058 rpm
The total current drawn by the motor, I = Ia + If = 67 + 3 = 70 A
The back EMF,
[tex]Eb = V - IaRa - V_br = 250 - 67 × 0.18 - 2 × 1.5 = 235.24 V[/tex]
Power developed,
Pd = EbIa= 235.24 × 67 = 15,749.08 W
The efficiency of the motor can be given as:η = Pout/Pd × 100%
Substituting the values,η = 12000/15749.08 × 100%η = 76.221%
Rounding off to 3 decimal places,η = 76.221%.
Therefore, the efficiency of the given DC shunt motor is 76.221%.
To know more about resistance visit:
https://brainly.com/question/29427458
#SPJ11