Which statements about rainbows are true? Choose more than one answer.

Magnitude of the charge on each bead is calculated as 14.7 nC

In physics, charge is a characteristic of unit of matter that expresses the extent to which it has more or fewer electrons than protons.

As, F = kΔL, where F is the force, k is the spring constant, and ΔL is the change in length of the spring.

Given mass is 2.6 gm and unstretched length is 4.0 cm .

So, F = mg = 2.6g * 9.8 m/s^2

ΔL = 5.1 cm - 4 cm = 1.1 cm

Hence, k = F/ΔL = (2.6*9.8)/(0.011) = 469.09 N/m

ΔL = 4.4 cm - 4 cm = 0.4 cm

F = kΔL = 469.09 N/m * 0.4 cm = 187.63 N

As we know, q = F/E

q = 187.63 N / (1/(4π8.85410^-12)) = 1.4710^-8 C

So, the magnitude of the charge on each bead is 1.4710^-8 Coulombs, or 1.4710^-8 * 10^9 = 14.7 nC

To know more about charge, refer

https://brainly.com/question/28548981

#SPJ4

4.1) Resistance of the 6.2 V, 4.5 W lamp at its working potential difference (pd) is about 9.   4.2) The emf of the battery is 6.2V.

The energy used between two points in a circuit is called potential difference, therefore it is measured between two points either side of component.

4.1)To calculate the resistance of the lamp;

resistance = pd / current

pd is the potential difference across the circuit and current is the flow of electricity through circuit.

Given, potential difference across the lamp is 6.2 V and the power of the lamp is 4.5 W,

So, Power = pd x current

4.5W = 6.2V x current

current = 4.5W / 6.2V

Hence, current = 0.726 A

resistance = pd / current

resistance = 6.2 V / 0.726 A

resistance = 8.56 ohm, approximately 9 ohm

4.2 The emf of battery is the maximum potential difference of the battery, when no current is flowing through circuit. In this case, emf of the battery is the same as terminal pd across the battery which is 6.2V. So the emf of the battery is 6.2V.

To know more about potential difference, refer

https://brainly.com/question/24142403

#SPJ1

The impulse is equal to the average net external force times the length of time it takes for that force to act, as shown by the equation.

To learn more about  impulse refer

https://brainly.com/question/2193212

#SPJ1

Journalists frequently misinterpret research studies in their media articles in a number of ways. Such practices can lead to inaccurate and potentially harmful messages about scientific research.

Misinterpretation of research studies occurs in several ways:

First, journalists may inaccurately represent the findings of a study, either by overstating its conclusion or by misinterpreting its results. For example, they may suggest that a study shows a causative relationship between two variables when the actual findings only show a correlation.

Second, journalists may fail to provide enough context for readers to understand the research. This includes not providing enough information about the study sample and design, as well as failing to explain the statistical methods used in the analysis.

Third, journalists may selectively report on research studies, emphasizing those that are most sensational or that support a particular narrative. By omitting certain study results, they may give an incomplete picture of the research at hand.

Finally, journalists may report on studies that contain weak or unreliable evidence. This is particularly problematic when the research is based on a small sample size or uses methods that are not well-validated.

In summary, journalists are prone to misrepresenting research studies by giving an incomplete account of the findings, failing to provide adequate context, selectively reporting on studies, and relying on unreliable evidence. Such practices can lead to inaccurate and potentially harmful messages about scientific research.

Learn more about research studies:

https://brainly.com/question/9266703

#SPJ4

In order to determine the average normal stress at points D and E, we need to know the applied loading and the cross-sectional areas of the pipe and rod at these points.

It is assumed that pipe AB and solid rod BC form a built-up shaft that is subjected to an axial load, represented by P. The average normal stress at point D, which is located on the pipe, can be calculated by:

σD = P/A

Where A is the cross-sectional area of the pipe at point D. The cross-sectional area of the pipe can be calculated by:

A = π/4 * (D_o^2 - D_i^2)

Where D_o is the outer diameter of the pipe and D_i is the inner diameter of the pipe

The average normal stress at point E, which is located on the rod, can be calculated by:

σE = P/A

Where A is the cross-sectional area of the rod at point E. The cross-sectional area of the rod can be calculated by:

A = π/4 * D_r^2

Where D_r is the diameter of the rod

Therefore, by substituting the given values into the above equations we can calculate the average normal stress at points D and E.

Learn more about Stress here: https://brainly.com/question/29488474

#SPJ4

The velocity of the log relative to the river is 3.04 km/182 min = 0.017 km/min.

Velocity is a vector quantity that describes the rate and direction of the movement of an object or particle. It is composed of two components: speed and direction.

The speed of the river is constant and is denoted by v. Therefore, the velocity of the motorboat is v + u, where u is the speed of the motorboat relative to the river.
When the person travels 1.52 km upstream, the total distance covered by the motorboat is 1.52 km x (v + u). This is also the distance covered by the log during the same period of time.
The time taken by the person to travel upstream is 91 min. Therefore, the total time taken by the motorboat to cover the round trip (upstream + downstream) is 182 min.
The total distance covered by the motorboat during the round trip is 3.04 km x (v + u). Since the same log is seen again, the distance covered by the log during the round trip is also 3.04 km.
Therefore, the velocity of the log relative to the river is 3.04 km/182 min = 0.017 km/min.

To learn more about velocity
https://brainly.com/question/24445340
#SPJ4

Answer:

  about 792 J

Explanation:

You want the mechanical energy lost by a 65.2 kg base runner who slides into second base from a speed of 4.93 m/s, reaching the base with a speed of 0.

The runner's kinetic energy is ...

  KE = 1/2mv²

  KE = 1/2(65.2 kg)(4.93 m/s)² = 792.33974 J

As the runner slides into second base, his speed decreases to zero, so all of his kinetic energy is lost to friction.

The energy lost to friction is about 792 J.

The average velocity of the marble based on the image is 2.75 m/s.

The ratio of the change in position or displacement (x) and the time periods (t) during which the displacement happens is known as average velocity.

Mathematically;

where;

The change in the displacement of the marble, ∆x = 7 m - (-4) m

The change in the displacement of the marble, ∆x = 11 m

The change in time, ∆x = 8/2 seconds

The change in time, ∆x = 4 seconds

The average velocity of the marble = 11 m / 4 seconds

The average velocity of the marble = 2.75 m/s

Learn more about average velocity at: https://brainly.com/question/28668011

#SPJ1

The appropriate values into the equation: E = (500 kg) (9.81 m/s2) (change in height between A and C).

An equation is a mathematical statement that expresses the relationship between two or more variables. It is composed of algebraic expressions, including constants, coefficients, variables, and operators, arranged in a particular order.

The energy loss due to friction from A to C can be calculated using the equation E = mgh, where m is the mass of the car (500 kg), g is the acceleration due to gravity (9.81 m/s2), and h is the change in height between points A and C.
Assuming that the track is level between A and C,
then the change in height is zero and the energy loss due to friction is also zero. If, however,
the track is not level and there is a change in height between A and C,
then the energy loss due to friction can be calculated by plugging in the appropriate values into the equation: E = (500 kg) (9.81 m/s2) (change in height between A and C).

To learn more about equation
https://brainly.com/question/26408808
#SPJ4

The fraction of its initial kinetic energy lost can be estimated to be 0.10 to 0.20.

Initial kinetic energy is the energy possessed by an object due to its motion. It is the energy of an object before any other external forces, such as gravity, friction, or air resistance, act upon it. Kinetic energy is a scalar quantity, meaning it has magnitude but not direction.

The fraction of kinetic energy lost will depend on the nature of the collision and the amount of energy dissipated. Generally, it is estimated that about 10% to 20% of the initial kinetic energy is lost in a collision. Therefore, the fraction of its initial kinetic energy lost can be estimated to be 0.10 to 0.20.

To learn more about initial kinetic energy
https://brainly.com/question/13026615
#SPJ4

The ball takes 1.62 seconds to return to the ground after reaching its  maximum height  As a result, the ball is in the ground for

1.5 seconds + 1.62 seconds, which is 3.12 seconds.

The student  throws the ball with the initial velocity vi=15m/s

The final velocity of the ball is [tex]v_{f} =0 \\[/tex] The gravitational acceleration is g=10m/[tex]s^{2}[/tex]

Let the maximum height the ball reached is  s

Using the equation of motion,

[tex]v_{f} ^{2} -v_{i} ^{2} =2gs-(15)^2[/tex]=11.25m

Consequently, the ball traveled 11.25 meters from student height till it began to fall to the ground. Identify the time t right now.Taken by ball to reach the height 11.25 musing the equation of motion

[tex]v_{f} =v_{i}+gt_{o}=15+(-10) t_{t} =1.5sec[/tex]

As a result, the ball reaches its highest point in 1.5 seconds.

Given that the girl's hand was 2 meters above the ground. Consequently, the ball travels the distance before touching the ground.

11.25m + 2m = 13.25m

Using the equation of motion

[tex]S=v_{i} t+\frac{1}{2} gt^{2}[/tex]

S=13.25m, [tex]v_{i} =0[/tex], g=10m/[tex]s^{2}[/tex]

Substitute the values,

[tex]13.25=0 +\frac{1}{2} (10)t^{2}[/tex]

t=[tex]\sqrt\frac{13.25}{5}[/tex]

t=1.62sec

The time taken by ball to return to ground from maximum height is 1.62 sec.

Hence, The ball remains in ground before it hits the ground is 1.5 sec + 1.62 sec = 3.12 sec

Learn more about maximum height

brainly.com/question/6261898

#SPJ4

999mm is added to 100m, we get​ 100999m.

A unit conversion is defined as the same property as a different unit of measurement such that time can be expressed in minutes instead of hours, while distance can be expressed in miles to kilometers or feet or lengths which can be converted to any other measurement.

In the above given information,

We have two numbers which are 999mm and 100m

So, we have to convert 100m into mm.

we know, 1cm=10mm

                     1m=100cm=100×10=1000mm

100m will be=100×1000=100000mm

Now, after adding 999m with 100000mm,

999mm+100000mm =100999mm

Hence, when 999mm is added to 100m we get 100999m.

Learn more about conversion of units, here:

https://brainly.com/question/19420601

#SPJ1

In 2.90 seconds, a train can accelerate from 10.0 m/s to 15.0 m/s, and this train accelerates at a rate of 1.94 ms2/m/s2.

At the start of the trip, the train picks up speed as it accelerates. In the middle of the journey, it remains the same (where there is no acceleration). When the train comes to a stop, it gets smaller as it slows down.

Distance traveled by the train as a percentage of time is its speed. The time it takes for two trains to cross each other is determined by the length of the trains, say lengths a and b, and the speeds of the trains, x and y, respectively.

In 2.90 seconds, a train can accelerate from 10.0 m/s to 15.0 m/s, and this train accelerates at a rate of 1.94 ms2/m/s2.          

To learn more about acceleration refer to:

https://brainly.com/question/460763

#SPJ1

The four different forms of speed are as follows: uniform speed. variable rate Typical rate.

To learn more about speed refer to:

https://brainly.com/question/13943409

#SPJ1

It will take 91.125 sec (approximately 1 min and 30 sec) to complete the process using a hot pot with a power rating of 600 watts.

The process of converting 150 pieces of ice at -15 degrees Celsius into liquid water at 50 degrees Celsius is an endothermic process, meaning that heat is absorbed by the system. To represent this process in an energy-interaction diagram, we would start with the initial state of the ice at -15 degrees Celsius, with the horizontal axis representing the amount of energy absorbed by the system (in joules) and the vertical axis representing the temperature. As heat is added to the system, the temperature of the ice will increase, and the energy absorbed by the system will also increase. The process will continue until the ice has completely melted and reached a temperature of 50 degrees Celsius, at which point the energy absorbed by the system will reach its maximum value.

The amount of heat added to the system to complete this process can be calculated using the formula:

Q = mcΔT

where Q is the heat added (in joules), m is the mass of the ice (in kilograms), c is the specific heat capacity of ice (about 2.1 J/gC), and ΔT is the change in temperature (50 - (-15) = 65 degrees Celsius). The heat absorbed by the system is therefore calculated as follows:

Q = 150 pieces × 0.02 (kg/piece) × 2.1 (J/g*C) × 65(C) = 54675 J

It will take 91.125 sec (approximately 1 min and 30 sec) to complete the process using a hot pot with a power rating of 600 watts.

The process of converting 150 pieces of ice at -15 degrees Celsius into liquid water at 50 degrees Celsius is an endothermic process, meaning that heat is absorbed by the system. To represent this process in an energy-interaction diagram, we would start with the initial state of the ice at -15 degrees Celsius, with the horizontal axis representing the amount of energy absorbed by the system (in joules) and the vertical axis representing the temperature. As heat is added to the system, the temperature of the ice will increase, and the energy absorbed by the system will also increase. The process will continue until the ice has completely melted and reached a temperature of 50 degrees Celsius, at which point the energy absorbed by the system will reach its maximum value.

The amount of heat added to the system to complete this process can be calculated using the formula:

Q = mcΔT

where Q is the heat added (in joules), m is the mass of the ice (in kilograms), c is the specific heat capacity of ice (about 2.1 J/gC), and ΔT is the change in temperature (50 - (-15) = 65 degrees Celsius). The heat absorbed by the system is therefore calculated as follows:

Q = 150 pieces × 0.02 (kg/piece) × 2.1 (J/g*C) × 65(C) = 54675 J

To find out how long it will take to complete the process using a hot pot with a power rating of 600 watts, you can use the formula:

time (in seconds) = energy (in joules) / power (in watts)

time = 54675 J / 600 W = 91.125 sec (approximately 1 min and 30 sec)

To know more about endothermic process, visit:

https://brainly.com/question/29555731

#SPJ4

Symmetry: According to the problem the charge on the larger ring is 4q.

Symmetry is a type of balanced arrangement of parts or elements of a whole. It is a fundamental concept in mathematics, art, and nature. Symmetry can be seen in everyday objects, such as a human face, a butterfly, a snowflake, and a fingerprint.

This is because of the symmetry of the system. The electric field due to the smaller ring at point P is the same as the electric field due to the larger ring at point P, since the distance from point P to the center of both rings is the same. Since the charge on the smaller ring is q, the charge on the larger ring must also be q in order to produce the same electric field. Since the larger ring has four times the area of the smaller ring, the charge on the larger ring must also be four times that of the smaller ring, which is 4q.

To learn more about Symmetry
https://brainly.com/question/26275735
#SPJ4

Answer:

A pH meter that reads 0.5 off or a calculator that rounds incorrectly would be the source of instrumental errors.

Answer:

Hi ??? what is your question

Respect to the ultimate strength, determine the total load p=294k that can be supported by the pad.

What is meant by strength?

σ U =50ksi

n=3.5

σ allow = nσ /U = 50ksi/3.5 =14.29ksi

d=4.5in.

t=0.4in.

[tex]d_{0}[/tex] =d−2t=3.7in.

A= π/4 [tex](d^{2} -d^{2} _{0})[/tex] = π/4[[tex](4.5in.)^{2} (3.7in.) ^{2}[/tex] ]=5.152[tex]in.^{2}[/tex]

P 1 = allowable load on one pier

P 1 =σ allowA =(14.29ksi)(5.152[tex]in.^{2}[/tex])=73.62k

Total load P = [tex]4P_{1}[/tex]=294k

To learn more about strength refer to

https://brainly.com/question/26998713

#SPJ4

Elements are most simply made up of atoms. A pure element will only have one type of atom, for example, a pure chunk of gold will only have gold atoms, making it chemically pure.

Two identical atoms bonded chemically, most frequently by covalent bonds, to form a molecule. Halogens are typically diatomic molecules; for example, chlorine is known as Cl2.

A pure substance is made up of various elements that have been chemically combined. Ionic chemicals that are connected by ionic bonds are the most common way to observe this. Please remember that a compound is not the same as a mixture! Keep in mind that a combination is not linked chemically.

to know more about molecules, compounds and pure substances, see

https://brainly.com/question/475709

https://brainly.com/question/26487468

https://brainly.com/question/18634105

To determine the magnitude of the applied force, normal force, and friction force, we can use the equations of motion.

The applied force (Fa) is the force that Marsha exerts on the box. It can be determined by the equation:

Fa = ma

where m is the mass of the box (12 kg) and a is the acceleration of the box (which is zero, since the box is moving at a constant velocity).

The normal force (FN) is the force exerted on the box by the surface it is sliding on, perpendicular to the surface. It can be determined by the equation:

FN = mg

where g is the acceleration due to gravity (9.8 m/s^2).

The friction force (Ff) is the force exerted on the box by the surface it is sliding on, parallel to the surface. It can be determined by the equation:

Ff = μFN

where μ is the coefficient of kinetic friction between the box and the surface (0.70).

So,

Fa = 12 * 0 = 0 N (since acceleration is zero)

FN = 12 * 9.8 = 117.6 N (perpendicular to the surface)

Ff = 0.7 * 117.6 = 82.32 N (parallel to the surface)

So the magnitude of applied force is 0 N, normal force is 117.6 N, and friction force is 82.32 N

Learn more about : friction force
https://brainly.com/question/24386803

The free-fall and oscillation sections, which is [tex]$3.02 \ s + 2.01 \ s = 5.03 \ s$[/tex].

Oscillation sections are sections of a waveform that repeat themselves over a certain period of time. This period of time is known as the oscillation period and is typically measured in seconds or milliseconds.

The time interval between the bungee jumper leaving the bridge and reaching the bottom of her motion can be found by summing the time intervals associated with the free-fall and oscillation sections of the motion.
The time interval associated with the 15.0 m free-fall can be found using the equation for the time it takes an object to fall a given distance, which is:
[tex]$t_{fall} = \sqrt{\frac{2d}{g}}$[/tex]
where d is the distance fallen and g is the acceleration due to gravity, which is [tex]9.81 m/s$^2$.[/tex]
Therefore, the time interval associated with the free-fall can be calculated as follows:
[tex]$t_{fall} = \sqrt{\frac{2 \cdot 15.0 \ m}{9.81 \ m/s^2}} = 3.02 \ s$[/tex]
The time interval associated with the 26.0 m of oscillation can be found using the equation for the period of a simple harmonic oscillator, which is:
[tex]$T = 2 \pi \sqrt{\frac{m}{k}}$[/tex]
where $m$ is the mass of the object and k is the spring constant.
In this case, the mass of the object is 64.0 kg, and the spring constant is the force of gravity acting on the jumper, which is [tex]$mg = 64.0 \ kg \cdot 9.81 \ m/s^2 = 628.64 \ N/m$[/tex]
Therefore, the time interval associated with the oscillation can be calculated as follows:
[tex]$T = 2 \pi \sqrt{\frac{64.0 \ kg}{628.64 \ N/m}} = 2.01 \ s$[/tex]
The total time interval between the bungee jumper leaving the bridge and reaching the bottom of her motion is the sum of the time intervals for the free-fall and oscillation sections, which is [tex]$3.02 \ s + 2.01 \ s = 5.03 \ s$[/tex].

To learn more about harmonic oscillator
https://brainly.com/question/26114128
#SPJ4

The area of contact between the block and the surface is 50 m².

A body's mass is an inherent quality. Before the discovery of the atom and particle, it was widely considered to be tied to the amount of matter in a physical body.

The measure of matter in a particles or object is represented by the dimensionless quantity mass (symbolised m). The kilogramme is the International System's (SI) preferred unit of mass (kg).

Pressure is defined as force applied on a body per unit area. Pressure is the force perpendicularly applied to an object's surface per unit area over which that force is distributed. Gauge pressure is the pressure in relation to the outside pressure. There are many different units used to express pressure.

Given,

mass(m) = 50kg

pressure (p) = 10N/m²

Taking,

g= 10 m/s²

p= mg/A⇒ 10= 50 × 10/A∴

A= 500/10 = 50 m²

To know more about pressure, visit :

brainly.com/question/28012687

#SPJ1

the input force by the output force 2. by adjusting the force's necessary application direction 3. 3N4. W=△E5.

Direction can refer to the way something moves, the way you must go to get somewhere, the way something is beginning to take shape, or the direction you are facing. When you turn right rather than left, that is an illustration of direction.

Your direction perception refers to your capacity to generally understand where you are or which course to go, even if you're in a strange environment. He quickly got lost due to his weak sense of direction. If you claim someone

To know more about direction visit:

https://brainly.com/question/13899230

#SPJ1

According to Newton's law of cooling, the rate of cooling is inversely related to the temperature differential between the object and its surroundings. For this, the equation is:

dT/dt = k (T - Ts) (T - Ts)

where T is the object's temperature, Ts is the environment's temperature, and k is the cooling constant. where dT/dt is the rate of change in temperature.

This equation can be used to calculate the cooling constant k for the cup of tea. We know that the temperature started off at 95 degrees Celsius, dropped to 75 degrees Celsius, and took 5 minutes to cool down.

95 - 75 = 20, dT/dt = k (20), dT/dt = k (20) *(1/5), and dT/dt = 4k.

Then, we can determine how long it will take for the temperature to cool to the desired level by using this cooling constant and the target temperature (35°C).

35 - 75 = -40\s-40 = 4k(t) (t)

t = -40 / 4k

We are unable to solve for t since we lack the value for k. But if we assume that the cooling rate is comparable to the rate we currently know, we can come up with an estimate. If we assume that the rate of cooling is constant, we can calculate how long it will take for the tea to cool from 75 to 35 degrees by using the rate of cooling from 95 to 75 degrees.

t = -40/20 equals 2 minutes.

It would take around 2 minutes to cool the tea from 75c to 35c under the assumption of similar cooling rate.

To learn more about newton's law of cooling:

https://brainly.com/question/13748261

#SPJ4

The rules of energy conservation and angular momentum conservation ensure that any rotating, collapsing cloud will finish up as a spinning disk.

Momentum is defined in Newtonian physics as the product of an object's mass and velocity. It is a vector quantity with magnitude and direction. Momentum is a measure of mass in motion: how much mass is involved in how much movement. It is commonly denoted by the sign p. Momentum is clearly defined as the measure of an object's kinetic energy. In layman's terms, momentum is the product of mass and velocity. Complete response: Simply said, momentum is concerned with the quantity of motion. It can also be referred to as the preserved quantity.

Here,

The laws of energy and angular momentum conservation guarantee that any rotating, collapsing cloud will end up as a spinning disk.

To know more about momentum,

https://brainly.com/question/22418297

#SPJ4

The current in each of the single wires being the same in an electric circuit with a single wire connected to three branches that contain resistors and then connecting back to a single wire is explained by the conservation of charge.

Conservation of charge states that total charge in an isolated system remains constant. In electric circuit, charge flows through circuit in the form of electric current. Therefore, amount of charge flowing into any point in the circuit must be equal to the amount of charge flowing out of that point.

This means that current flowing into a branch in the circuit must be equal to the current flowing out of that branch. As the current in the single wire connected to the three branches is the same, current flowing into and out of each branch must also be the same, as per the conservation of charge principle.

To know more about electric circuit, refer

https://brainly.com/question/2969220

#SPJ4

Answer:

In physics, the amount of work done on an object is the product of the force applied to the object and the distance over which the force is applied, also known as the force's displacement. Mathematically, it is represented as W = F * d.

Explanation:

If the total number of joints in a simple truss is three, the total number of members in the truss is three.

In engineering, a truss is a structural member made of straight pieces of metal or wood that are joined together to form a series of triangles that lie in a single plane. Roofs, bridges, and towers are the most common structures that use trusses. Truss structures are classified into three types: simple, planar, and space frame. Various truss varieties have been developed over the years within these three basic types. A framework is made up of straight members joined at their ends to form a truss structure. Trusses can support both moving and stationary loads. Trusses are commonly used in roof supports, bridges, and other similar structures.

Here,

m=2j-3

j=3

m=2*3-3

m=3

The total number of members in the truss is 3 if the total number of joints in a simple truss is three.

To know more about truss,

https://brainly.com/question/12937335

#SPJ4

The angle its final velocity makes with the horizontal is 60⁰.

The time taken for the particle to travel through the 0.9 m radius is calculated by applying the following equation.

t = ( 2v sin (θ) ) / g

where;

t = ( 2 x 0.55 x sin 30 ) / ( 9.8 )

t = 0.056 s

The final vertical velocity is calculated as follows;

Vy = Vi + gt

Vy = ( 0.55 x sin 30 ) + (9.8 x 0.056 )

Vy = 0.82 m/s

The final horizontal velocity is calculated as follows;

Vx = V cos (30)

Vx = 0.55 m/s  x  cos ( 30 )

Vx = 0.48 m/s

The angle made with the horizontal is calculated as;

θ = arc tan ( Vy / Vx )

θ = arc tan  ( 0.82 / 0.48 )

θ = 59.7⁰ ≈ 60⁰

Learn  more about angle of projection here: https://brainly.com/question/4275218

#SPJ1