Laser beam machining and water jet cutting are the following processes would be appropriate for cutting a narrow slot, less than 0.015 inch wide, in a 3/8- inch thick sheet of fiber-reinforced plastic. Hence option d and f is correct.
What is fiber reinforced plastic?Fiber reinforced plastic is defined as a polymer-based composite material that is strengthened by fiber support. Fiber-reinforced plastics (FRP) are composite materials that use glass or carbon fibers as reinforcement and polymer resins as a matrix.
Because laser cutting is a far less aggressive and abrasive process than water jet cutting, it is much more accurate. A laser can carefully and safely cut materials as thin as 0.006 inches, whereas water jet cutters can't handle cutting through surfaces smaller than 0.02 inches.
Thus, laser beam machining and water jet cutting are the following processes would be appropriate for cutting a narrow slot, less than 0.015 inch wide, in a 3/8- inch thick sheet of fiber-reinforced plastic. Hence option d and f is correct.
To learn more about fiber-reinforced plastic, refer to the link below:
https://brainly.com/question/11941367
#SPJ1
When a metal car is struck by lightning, the resulting electric field inside the car is.
Inside the automobile, there is no electric field.
What is the electric field inside the car like?It is safest to remain inside the car during an electrical storm since the metal body acts as a Faraday cage, containing no electrical field.There isn't an electric field inside the car as a result.Once a capacitor is fully charged, its overall electron content remains constant.There is absolutely no electric field inside of a conductor.Just outside of charges on a conductor's surface, where they begin or end, the electric field lines are perpendicular to the surface.To learn more about the electrical field refer to:
https://brainly.com/question/24317284
#SPJ4
which fields in an ip packet header are examined by netflow to determine whether or not a given packet is part of a flow? (select two.) answer header
Destination port, Layer 3 Protocol Type.
What is neflow?Around 1996, Cisco routers began to include a function called NetFlow that allowed users to record IP network data as it entered or left an interface. A network administrator can identify factors like the source and destination of traffic, the class of service, and the reasons for congestion by evaluating the data produced by NetFlow. Three primary parts make up a typical flow monitoring configuration (using NetFlow):Aggregating packets into flows, a flow exporter sends flow records to one or more flow collectors.The flow exporter sends data to a flow exporter, which the flow collector receives, stores, and pre-processes.Application for analysis: Examines received flow data in the context of traffic profiling or intrusion detection.To learn more about netflow, refer to
https://brainly.com/question/29511210
#SPJ4
technician a says that some dc motors use brushes. technician b says that an ac synchronous motor uses a permanent magnet rotor. which technician is correct?
When technician A claims that some dc motors employ brushes, technicians B and A both make the appropriate corrections. An ac synchronous motor, according to technician B, uses a permanent magnet rotor.
What applications do AC synchronous motors serve?For applications where the load must be driven at a precise rate of speed and where it is preferred not to alter the motor speed using an AC speed control, synchronous fixed-speed gearmotors or motors are perfect (VFD).
Which two main rotor types are employed in synchronous generators?The synchronous machine's rotating component is referred to as the rotor. It carries the twisting field. Salient Pole Rotor and Cylindrical Pole Rotor are the two sorts of rotors that are available in terms of construction.
To know more about synchronous motor visit:-
https://brainly.com/question/27189278
#SPJ4
Consider a unity-feedback control system with the open-loop transfer function G(s) = K/ (s(s^2+s+4)
A) Determine the value of the gain K such that the phase margin is 50∘?
B) What is the gain margin for this case?
A) The phase margin is given by PM = -tan-1 (ωc/ζ) - 180
where ωc is the critical frequency and ζ is the damping ratio.
For a phase margin of 50°, we have
-tan-1 (ωc/ζ) = -130°
or
ωc/ζ = tan 130°
Now, the damping ratio is given by
ζ = -log(GM)/(√π2 + log2(GM))
where GM is the gain margin.
Substituting for ζ in the above equation, we get
ωc = tan 130° × -log(GM)/(√π2 + log2(GM))
Solving for GM, we get
GM = exp(-tan 130° × √π2 + log2(GM))
Now, we can calculate the gain K from the open-loop transfer function G(s) = K/ (s(s2 + s + 4))
K = GM × (s2 + s + 4)
Substituting for GM, we get
K = exp(-tan 130° × √π2 + log2(GM)) × (s2 + s + 4)
Hence, the value of the gain K such that the phase margin is 50° is given by
K = exp(-tan 130° × √π2 + log2(GM)) × (s2 + s + 4).
B) The gain margin for this case is given by
GM = exp(-tan 130° × √π2 + log2(GM))
For more questions like Transfer function click the link below:
https://brainly.com/question/17438230
#SPJ4
traditional hydraulic and pneumatic control systems are being replaced by what types of systems to save in weight?
There is no proof that hydraulics is always more "efficient" in every circumstance, however it might be in some applications.
What would happen if a pneumatic system took the place of the hydraulic system? There is no proof that hydraulics is always more "efficient" in every circumstance, however it might be in some applications.It is "more efficient" to use hydraulics when:mobile tools for earth moving and construction .Presses for shaping metal,machinery for extrusion, especially plastics.Various lift types, such as elevators and platforms than pneumatic machineryAlternatively, pneumatics:work more quickly than hydraulics.yastmastmastmastmas, and can be utilized for applications requiring significantly higher precision.are significantly safer around processes involving food, drinks, and medicines.are safer in terms of substantially lower flammability and the risks of piping failures that go along with it.To learn more about hydraulic refer
https://brainly.com/question/857286
#SPJ4
8-33. Bar abc has a rectangular cross section of 300 mm by 100 mm. Attached rod db has a diameter of 20 mm. Determine the slope at a due to the loading. Consider only the effect of bending in abc, and axial force in db. E-200 gpa. D. O300 mm 20 kn 100 mm.
Answer: the answer is in the photo
Explanation:
assume it is important that the warping not exceed 0.5 mm. an engineer suggests that if the temperature is kept below the level computed in part (e), we can be sure that the warping will not exceed 0.5 mm. is this a correct conclusion? explain.
This is not the right conclusion, no. Temperature is one of many factors that might induce warping, but this is not the only one. Warping can also be influenced by other elements like humidity.
What is temperature ?
The physical concept of temperature indicates in numerical form how hot or cold something is. A thermometer is used to determine temperature. Thermometers are calibrated using a variety of temperature scales, which historically defined distinct reference points and calorimetry substances. As a result, maintaining the temperatures below the value calculated in part (e) is insufficient to ensure that the warping is not greater than 0.5 mm.
To know more about temperature
https://brainly.com/question/24746268
#SPJ4
explain how lead and lag indicators are used in a quality program to develop measurement systems, and link your response with the use of a sweatt model, as discussed during week 4.
A leading indicator anticipates future results and occurrences.
A trailing indicator evaluates whether the desired outcome was realised in the past.
Why lead and lag indicators used ?In performance evaluation and management, the terms "leading indicator" and "lagging indicator" have come to be considered standard language. However, the line separating the two can occasionally be a little blurry; some indications, for example, are a little of both.
If managers want to develop a precise picture of performance, they must ensure that both types of metrics are in place and grasp the differences between the two.
A leading indicator anticipates future results and occurrences.
A trailing indicator evaluates whether the desired outcome was realised in the past.
The goal of leading indicators is future prediction. In economics, the phrase "leading indicator" refers to a quantifiable economic factor that shifts before the economy begins to exhibit a certain pattern or trend.
To learn more about leading indicator refer to :
https://brainly.com/question/1357308
#SPJ4
technician a recommends backward flushing an oil cooler with solvent after repairing an engine that had damaged bearings. technician b says that servicing the oil cooler when bearings are damaged is unnecessary. who is correct?
Technician A is correct. Thus, recommends backward flushing an oil cooler with solvent after repairing an engine that had damaged bearings.
Antifreeze can cause contamination are improved oil viscosity or thickening of the oil (as witnessed), formation of gels and emulsions, formation of corrosive acids, premature filter plugging, and poor peripheral lubrication. The most general effect of high oil pressure is engine temperature, which ultimately makes the temperature of oil increase. Engine elements that are not functioning can also make an oil pressure increase. Low oil level refers to the most general cause of low pressure; it's also the easiest to fix. Oil changes are crucial, and between oil changes, it's just as a credential to check your motor's oil level regularly and add it as necessary.
Learn more about oil, here https://brainly.com/question/29530758
#SPJ4
draw the shear and moemnt diamgrams for the beam subjected to the concentrated loads. what are the values of the shear force and bending moment at x
Since the beam is symmetrical, the support reaction will be same i.e. VA = VC = 100 kN. shear force is zero & bending moment is zero
Share force is SFaleft=0Staright
100KNSFbleft=100KNSFbright=100-200
=-100KNSFcleft=-100KNSFcright=0
Bending moment is BMa=0Bmb
=100*5
=500KNBMc
=100*10-200*5=0
All the forces operating on either side of the section are added together algebraically to form the shear force. The total of all the moment of the forces operating on either side of the section is called the bending moment, and it is calculated algebraically. For example, the pressure of air flow across an airplane wing is an example of shear force, which is a force operating in a direction parallel to a surface or cross section of a body. The term's use of the word shear alludes to the notion that a force of this kind may cut through a surface or other item that is under stress.
Learn more about shear force here:
https://brainly.com/question/13195242
#SPJ4
tech a states that several types of superchargers are manufactured for use on vehicles. tech b states that the oldest version is the roots-style supercharger. who is correct?
Available superchargers include blowers or "turbochargers" powered by engines. The turbocharger is the most popular way of supercharging these engines, with the exception of a few small engines.
Exhaust gas expansion is used by turbochargers to pump combustion air into an engine. Another innovation in internal combustion engines of the piston type that boosts performance is the supercharger. It is an air compressor that raises the pressure or density of air that enters the combustion chamber of an engine to facilitate heavy duty operation. The roots style supercharger is the oldest type of supercharger and was first used as an industrial air-moving device in the early 1900s.
Learn more about engine here-
https://brainly.com/question/27162243
#SPJ4
What is the driving force for (a) heat transfer, (b) elec- tric current flow, and (c) fluid flow?
Answer:
A: mobile elecrons
B: electromotive force
c:bonds in the ions
isotropic point sources each emitting s neutrons/sec are placed in an infinite moderator at the four comers of a square of side a. compute the flux and current at the midpoint of any side of the square and at its center.
The flux and current at the midpoint of any side of the square and at its center are given by 16 x (s/a2) and 16 x (s/a) respectively.
The total flux at the midpoint of any side of the square is given by:
Flux = 4 x (s/a2)
The total current at the midpoint of any side of the square is given by:
Current = 4 x (s/a)
Flux and current at the center of the square
total flux at the center of the square is given by:
Flux = 16 x (s/a2)
The total current at the center of the square is given by:
Current = 16 x (s/a)
Therefore flux and current at the midpoint of any side of the square and at its center are given by 16 x (s/a2) and 16 x (s/a) respectively
For more questions like Flux click the link below:
https://brainly.com/question/29667955
#SPJ4
LetAandBbe regular languages. Is the set of strings of odd lengin fromAbeginning with 0 concatenated with the set of strings of even length fromBending with 0 a regular language (yes or no). Explain your answer sufficiently to convince me that you are correct.
By emphasizing our experience with a specific talent that the role requires, into specific detail about that experience and how you have previously used it.
By doing this, the hiring manager will get a chance to review some of your work and decide whether it meets their criteria for a candidate. Use a few of your strengths that are relevant to the job requirements as the foundation of your response to the question of what sets you apart from other applicants. These could be personal traits, professional abilities, areas of specialization, or other relevant experiences. This is a fantastic response because the interviewee highlights the success of the company and their contribution to this success while also referencing key skills from the job description.
Learn more about specific here-
https://brainly.com/question/19819958
#SPJ4
In which of the following areas does a WAN differ from an internetwork? (Choose all that apply.)
a. WANs use service providers for the network connection.
b. WANs can't transport Network-layer protocols.
c. WANs use serial communication technologies that can span miles.
d. WANs don't use
Option a is correct. The following area in which WAN differ from an internetwork is WANs use service providers for the network connection.
Wide area networks are telecommunications systems that cover a large geographic area (WAN). Wide area networks are commonly put up using leased telecom connections.
Wide area networks are used by businesses to transmit information to employees, students, clients, purchasers, and suppliers in different parts of the world. Governments and educational institutions also employ them. In essence, this method of communication makes it possible for a business to effectively do its regular activities wherever it is. The Internet might be categorized as a WAN.
A computer network that covers several continents, or even the entire planet, is often referred to as a WAN.
However, it may be best to view WANs as computer networking technologies used to transmit data over long distances in terms of the application of communication protocols and concepts.
To know more about WAN click here:
https://brainly.com/question/621746
#SPJ4
I need help with this problem
Answer:
good question but i cant solve
Explain on a structural basis the differences in the glass transition temperature of polyethylene ( =-140°C), polyvinylchloride (T-87 C), and polysityrene (Tg= 100 c)
The "glass transition" temperature is the point at which it happens. For instance, low-density polyethylene has a glass transition temperature, or Tg, of about 100°C.
He claims that the fact that the Tg of PVC/CF composite is higher (86.7 °C) than the Tg of pure PVC (76.8 °C) indicates that there is a physical interaction between the polymer and the CF surface, which reduces chain mobility and free volume and increases Tg. Pressure and free volume. Increased surrounding pressure causes a decrease in free volume, which ultimately results in increased Tg. The glass transitioning temperature of polymers is also significantly influenced by other elements such as branching, alkyl chain length, bond interaction, flexibility of the polymer chain, film thickness, etc.
Learn more about transitioning here-
https://brainly.com/question/28791143
#SPJ4
state whether stress increased or decreased pulse rate. which division of the ans caused this change?
This alteration was brought on by the sympathetic wing of the ans.
Which section of the ANS causes the heart rate to drop?When the body is at ease, resting, or eating, the parasympathetic nervous system is in charge of the digestion and rest response. In essence, it reverses the effects of sympathetic division following a stressful event. The parasympathetic nerve system speeds up digestion while slowing down breathing and heart rate.
What section of the autonomic nervous system is involved in stress response?Sympathetic nervous system: This system stimulates bodily functions that support you when you're in need, particularly during stressful or dangerous situations. The "fight-or-flight" reaction in your body is controlled by this system.
To know more about sympathetic visit:-
https://brainly.com/question/7495218
#SPJ4
some fiber optic communication systems use laser amplification to boost the intensity of light pulses passing through an optical fiber. a short segment of laser amplifier fiber is spliced into the main fiber so that the light pulses must pass through the laser amplifier fiber on their way to their destination. the light emerging from the laser amplifier fiber is much brighter than it was when it entered. one interesting aspect of the light emerging from the laser amplifier fiber is that it
In some fiber optic communication, the light emerging from the laser amplifier fiber is much brighter than it was when it entered. one interesting aspect of the light emerging from the laser amplifier fiber is that ithas the same color as the light entering the amplifier fiber.
What is Fiber amplifiers?
Fiber amplifiers are optical amplifiers that use optical fibers for laser gain. A glass fiber do*ed with rare earth ions such as erbium (EDFA = erbium-do*ed fiber amplifier), neodymium, ytterbium (YDFA), praseodymium, or thulium is typically used as the gain medium.
This active dopant is pumped (charged) with light from a laser, such as a fiber-coupled diode laser; in almost all cases, the pump light travels through the fiber core with the signal to be amplified. Raman amplifiers are a type of fiber amplifier that is not commonly used.
To learn more about Fiber Optics, visit: https://brainly.com/question/15741826
#SPJ4
technician a states the mil lamp is required to come on any time a dtc is stored in an ecu. technician b says the mil light is required to come on any time there is a failure that could cause the emissions of the vehicle to exceed 1.5 times the emission standards for that vehicle. who is correct?
Both technicians are correct as the statement made by both are true. Therefore, Option C is the correct option.
Who are technicians?Technicians are knowledgeable professionals who work in almost every industry. They are asked to service, install, replace, and repair a variety of systems and equipment. They are adept in the relevant knowledge, abilities, and methods required by their line of work, which includes the automotive, maintenance, HVAC, and pharmaceutical industries.
Technicians examine, analyze, and troubleshoot client systems and equipment. They perform tests and analyze the results to formulate sound advice on how to repair malfunctioning or damaged equipment. They will negotiate prices with suppliers and customers to obtain replacement parts when necessary during repairs.
Before beginning a job, they will offer time and material cost estimates as well as repair and replace damaged equipment. Some technicians draft reports, safety guidelines, and preventive maintenance schedules.
Learn more about technicians
https://brainly.com/question/18428188
#SPJ4
Which of the following are fundamental intuitions behind collaborative filtering? A) Similar users will rate the items similarly B) Similar users will not rate the items similarly C) Similar items will be rated similarly Answer choices Select only one option Only A and BOnly B and C Only A and C Only A
Option A is correct. Similar users will rate the items similarly are fundamental intuitions behind collaborative filtering.
A line segment's exact midpoint is the point that lies halfway between its two endpoints. It is therefore the average of the two endpoints, which is the average of the two x- and y-coordinates. Discover the endpoints' coordinates. As a result, the electric field along OB at midpoint O is 5.4 106 N C1. (b) At mid-point O, a test charge in the amount of 1.5 109 C is positioned. Line OA is the direction of the force. This is due to the fact that the charge applied at point B repels the negative test charge whereas point A attracts it.
Learn more about average here-
https://brainly.com/question/28439704
#SPJ4
let $o$ denote the centroid of triangle $abc$. let $m$ and $n$ be points on sides $ab$ and $ac$, respectively, so that $m$, $o$, and $n$ are collinear, and $am/mb
The solution is 4/9≤r<1/2.The total area that is bounded by a triangle's three sides is referred to as the triangle's area.
Find the solution ?The total area that is bounded by a triangle's three sides is referred to as the triangle's area.In essence, it is equal to 1/2 of the height times the base, or A = 1/2 b h.
AB→=b→,AC→=c→AM→=λ(b→)AN→=μ(c→)
Let G divides MN in the ratio K:1
So, K+1Kμ(c→)+λ(b→)=3b→+c→
⇒K+1Kμ=31K+1λ=31K=μλλ1+μ1=31A.M≥G.M2λ1+μ1≥λ1.μ1
⇒λμ
≥32
Now, Area△ABCArea△AMN=21∣∣∣∣∣(b→)×(c→)∣∣∣∣∣21λμ∣∣∣∣∣(b→)×(c→)∣∣∣∣∣
=λμ
using λ1+μ1=31
Ratio =3λ−13λ2
which has a maximum value 21
So option C is correct
To learn more about triangle's area refer
https://brainly.com/question/21735282
#SPJ4
which one of the four types of chip would be expected in a turning operation conducted at low cutting speed on a brittle work material: (a) continuous, (b) continuous with built-up edge, (c) discontinuous, or (d) serrated?
In a turning operation carried out at a slow cutting conditions on a brittle work material, discontinuous forms of chips would be anticipated.
what is speed?
An object's speed, also known as "v," is the amount by which its position changes over time or by how much it changes per unit of time, making it a scalar number. The instantaneous speed is the upper limit of the average speed as that of the duration of the time period approaches zero. The average speed of an item in a period of time is equal to the distance travelled either by object divided either by duration of the term. Velocity and speed are not the same thing.
To know more about speed
https://brainly.com/question/13943409
#SPJ4
a) Compute VL, iL, iZ and iR for the network of the figure if RL = 180 ohms.
b) Repeat part (a) if RL = 470 ohms.
c) Compute the value of RL that will establish maximum power conditions for the Zener diode.
d) Compute the minimum value of RL to ensure that the Zener diode is in the "on" state.
a) Here, VL = 9v, IL = 50mA, Ir = 50mA for the network of RL= 180 ohms.
b) If RL = 470 ohms, then VL = 10v, IL = 21.276mA, Ir = 45.45mA
c) The value of RL that will establish maximum power conditions for the Zener diode, R[tex]_{L_{(max)}}[/tex] = 1.83 kΩ
d) The minimum value of RL to ensure that the Zener diode is in the "on" state R[tex]_{L_{(min)}}[/tex] = 220 Ω
What is Zener diode?A Zener diode is a particular kind of diode made to consistently permit current to flow "backwards" (with inverted polarity) when a specific reverse voltage, called the Zener voltage, is reached.
A wide range of Zener voltages, some of which are even variable, are used in the manufacture of Zener diodes. The reverse conduction occurs in some Zener diodes with sharp, highly dopped p - n junctions and low Zener voltages; in these cases, the Zener effect, named after Clarence Zener, is caused by electron quantum tunneling in the small gap between the p and n regions.
Avalanche breakdown also occurs during the operation of diodes with higher Zener voltages, which have a more gradual junction.
Learn more about Zener diode
https://brainly.com/question/13800609
#SPJ1
TRUE/FALSE. circuit components that are connected in such a way that they provide different current paths are said to be connected in parallel.
It's TRUE that circuit components that are connected in such a way that they provide different current paths are said to be connected in parallel.
What is Circuit?
A circuit in electronics is a complete circular path through which electricity flows. A basic circuit is made up of a current source, conductors, and a load. The term circuit can be used broadly to refer to any fixed path through which electricity, data, or a signal can travel.
How electronic circuits function?
In an electronic circuit, electrons exit the power source, travel along conductors, perform work in a load, and then return to the power source. The electrons flow in a circular path, which is why it is called a circuit. Ohm's Law describes the relationship between electrical flow and load. Electrons in a circuit travel from the negative side of the power supply to the positive side.
To learn more about Circuit, visit: https://brainly.com/question/26111218
#SPJ4
A box with two gases separated by an impermeable membrane is in an environment with temperature T. The membrane can move back and forth, but the gases cannot penetrate the membrane. We will assume that equipartition applies to both gases, but gas A has an excluded volume. . UA-? NAkT + constant . UB-aNBkT +constant Keep in mind that the total box volume is constant, so VA + VB = constant. equilibrium value of VA m
The thermal effects caused by putting a cylindrical fiber in an inviscid, perfect gas that an auditory wave travels through are described.
The thermal effects caused by putting a cylindrical fiber in an inviscid, perfect gas that an auditory wave travels through are described. The thermal conductivities and heat capacity of the fibers and the gas are limited. There are established expressions for the temperature distribution in the material and the gas.
Pressure oscillations in the gas, which are brought on by an acoustic wave's passage, are what cause the temperature distribution. It has been discovered that a dimensionless parameter's relative value can help determine whether the solution should be based on exact or approximative equations. This parameter depends on the thermal conductivities, heat capacities, acoustic frequency, and fiber diameter of the gas and fiber.
To know more about fiber click here:
https://brainly.com/question/28631296
#SPJ4
1. Consider the supply contract problem scenario that we discussed in class (and in Chapter 4). That is, the seller (supplier) is MTO; the seller pays a fixed cost of $100,000 to produce, and its per unit production cost is $35; the buyer pays the seller $80 per item purchased, and sells the items, for which there is a demand, for $125; the residual price is $20. As discussed, the globally optimal solution which maximizes the combined expected profit, is for the buyer to purchase Q* = 16,000 items. This results in a combined expected profit of $1,014,500. Suppose that the buyer and seller do not share any information beyond that given in the following contract: Suppose that the buyer and seller have a revenue sharing contract with Chew being the new cost per unit for the buyer in exchange for x% revenue sharing. Suppose Chew = CM = 35. Does there exist a value of x that will both: yield both the maximum combined expected profit and equally split it between the buyer and the seller? If so, determine this value of x. If not, explain why no such value exists.
No, there is not a value of x that will yield both the maximum combined expected profit and equally split it between the buyer and the seller. This is because the maximum combined expected profit ($1,014,500) is not evenly divisible by two. Therefore, the buyer and seller cannot split the expected profit equally. The theory at play here is the game theory.
What are the basics of game theory in economics?The study of an intuitive decision in which the outcome for each respondent or "player" is influenced by the actions of everyone else is known as game theory. If you are a participant in such a game, you must analyze the actions of others before deciding on your course of action or "strategy."
The following framework is useful for considering a scenario in which game theory is applicable. Define the issue
2. Determine the important components. Differentiated goods, first-mover advantage, entrance and exit charges, variable costs, and so on are examples of key elements.
3. Create a model, such as a bimatrix or extended-form game.
4. Use the model to hone your intuition.
5. Create a plan that addresses all probable eventualities.
Learn more about Game Theory:
https://brainly.com/question/28463553
#SPJ1
A rocket launches with a constant acceleration of a all the way to outer space, straight up. You are not sure what a is, but it is relative small (between 2 ft/s2 and 10 ft/s?). Ignore compressibility effects. The atmosphere follows a standard temperature and pressure profile (so you can compute the density ratio directly from 0). a. As a function of a, at what altitude will the rocket experience maximum dynamic pressure q? b. What is that pressure as a function of a? c. How does the answer vary with acceleration?
The abbreviation "Maximum dynamic pressure" is Max Q. It occurs when the rocket or spacecraft is under "maximum mechanical stress" during the launch.
Which simply means that the rocket is experiencing significant physical pressure as a result of traveling through the atmosphere's air at a very high speed. After the rocket has been launched for around 60 seconds and has reached an altitude of 11 km, Max Q occurs. Max Q for the Space Shuttle happens at a similar altitude, about. The maximum dynamic pressure, or Max Q, is reached when the dynamic pressure reaches its greatest level due to the increasing velocity.
Learn more about stress here-
https://brainly.com/question/17252580
#SPJ4
A 50 mm diameter shaft is subjected to a static axial load of 160kN. If the yield stress of the material is 350MPa, the ultimate tensile stress is 400MPa and the fatigue limit (endurance limit) for R = -1.0 is 320 MPa, what is the amplitude of the largest fullyreversed bending moment that can be applied to this shaft so that fatigue does not occur?
The amplitude of the largest fully reversed bending moment that can be applied to this shaft so that fatigue does not occur is 3.2kNm.
What is Goodman line equation?The Goodman relation (also referred to as a Goodman diagram, a Goodman-Haigh diagram, a Haigh diagram, or a Haigh-Soderberg diagram) is an equation used to calculate the impact of mean and alternating stresses on the fatigue life of a material. It is a subfield of material failure theory in the field of materials science.A parabola known as the Gerber line and a straight line known as the Goodman line can both (conservatively) approximate a scatterplot of experimental data displayed on an amplitude versus mean stress plot.Planning is still impacted by this situation, which dates back to the 1946 court case Goodman v. Commissioner of Internal Revenue. The ruling's main point is that the decision of who should receive the proceeds belongs to the policy's owner.Find the attachment answer
Learn more about Goodman relation refer to :
https://brainly.com/question/29508996
#SPJ4
what's the maximum size branch circuit protection for a single motor load if the motor is 480v, 3 phase, 11a using non-time delay
A 5-hp, 230V, single-phase motor's branch-circuit short-circuit protection (dual-element fuse) cannot be greater than 50A. A 25-hp, 460V, 3-phase synchronous motor's branch-circuit short-circuit protection (inverse-time breaker) must be greater than 70A.
What size branch circuit overcurrent protection is required for a motor?For a single motor utilized in a continuous duty application, under 430.22, the motor branch-circuit conductors must have an ampacity of at least 125 percent of the motor full-load current rating.
What is the motor branch's maximum rating?This gadget can withstand a maximum rating of 60A. It must be size down to 60A so as not to exceed the calculated 61A. The discussion of single motor computations and the Code is now complete.
To know more about single-phase motor's visit:-
https://brainly.com/question/29357924
#SPJ4